CATHODE RAY TOMES

Gravitar ST-206-01 1st Printing Backdoor Sheet

Gravitar (version 3) (Atari, 1982) · Backdoor Sheet · 1 pages · original scan

Page 1

Self-Test Procedure

Instruction Test Passes

  • Set the self-test switch to on. While holding the FIRE but- The screen shows the self-test display. RAMs, ROMs, and three ton down, press t-player start.* integrated circuits are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Seif: Test Procedure.
  • Activate control panel and coin switches, ‘As you activate the switches, you should hear a beep and the proper 0 should change to 1. If the test fails, refer to Chapter 2, Self-Test Procedure.

Each frame comer should be within %4-inch of each display bezel corner. If the test fails, refer to Chapter 2, Self-Test Procedure, Screen 2.

  • Observe the white frame at the sides of the screen.

“All credits are cancelled when you enter self-test

SWITCHSWITCH AT 4SWITCHSWITCHSWITCH ATD4 = SWITCH
TOGGLE8(Coinmodes)TOGGLE1TOGGLES(Gameplay)© TOGGLE1

FRAME

SELFTEST ‘SWITCH

FOR TECHNICIANS ONLY

RIGHT COIN SWITCH AT P10/11 Leciaiaaaai (Special options) LEFT COIN MECHANISM

COIN SWITCH

‘START SWITCH @ player)

SHIELDITRACTOR (Player 1)

START SWITCH

SHIELDITRACTOR FIRE ROTATE RIGHT ROTATE LEFT (1 player)

(Player 2)(Player 1)(Player 1)(Player 2)

FIRE ROTATE RIGHT ROTATE LEFT THRUST (Player 2) (Player 2) (Player 1) (Player 1)

Self-Test Display

NO. OF CREDITS PER COIN FOR GAME DIFFICULTY RIGHT COIN MECHANISM

NO. OF CREDITS *. we NO. OF CREDITS

FOR EACH PUSH OF 5 PER COIN FOR

UTILITY COIN SWITCHimeLEFT COIN MECHANISM

eee BONUS ADDER SRESS START AND FIRE

FOR TEST ““~.__ INSTRUCTION FOR SELF-TEST OR TO ERASE SCORES OR TIMES

SHIPS PER GAME————+ OOOoooo0g-———————_ NO. OF GAMES PLAYED

C Oooo: a ee AVERAGE COCKTAIL CABINET GAME TIME

Operator Information Display

The Operator information Display, shows game statistics. You may also erase game scores and times. To see this display, set the self-test switch to on.

To erase game times: To erase game scores and times: ‘PLAYER START until display 1. Push 1-PLAYER START until display

reads PRESS START 1 AND FIRE TOreads PRESS START 1 AND FIRE TOreads PRESS START 1 AND FIRE TO
CLEAR SCORES.CLEAR TIMES.CLEAR TIMES AND SCORES.
2. Press both FIRE and 1-PLAYER START.2. Press both FIRE and /-PLAYERSTART.2. Press both FIRE and 1-PLAYER START.
3. The word ERASING flashes on the3. The word ERASING flashes on the3. The word ERASING flashes on the
screen until the entire table is erased.screen until the entire table is erased.screen until the entire table is erased.
Walt until the word ERASING disap-Wait until the word ERASING disap-Wait until the word ERASING disap-
pears before going on with other tests.pears before going on with other tests.pears before going on with other tests.

To erase game scores:

4.Push‘PLAYER START until display1.Pu

To end the Operator information Display, set the self-test switch to off.

Game Play Options

This table contains the switch settings for options relating to game difficulty, language, bonus, and ships. The switches are on the game PCB at location D4, and are accessible when the game PCB is mounted in place.

Settings of &Toggle Switch on Gravitar game PCB (at D4)

876643924Option
OnOnNo bonus
OffOffBonus ship every 10,000 points
OnOffBonus ship every 20,000 points
OffOnBonus ship every 30,000 points

} H

=¢On=Easy game play <
38of§Hard game play
offoff3 ships per game
OnOff4 ships per game
OffOn5 ships per game
OnOn6 ships per game

“<Manutacturer’s recommended settings

Important Note to Operators: If the operation, maintenance and service manual, schematic package or video display manual was not included in this game when you unpacked it, contact your distributor to get a free copy. (All ATARI manuals for coin-operated games also include complete illustrated parts lists.) ST-206-01 ‘1st printing

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. To perform the self-test, set the self-test switch to on. Then simultaneously press the 1-player start and FIRE buttons. To end the self-test, set the self-test switch to off.

UTILITY PANEL

COIN SWITCH

COIN COUNTER: OPTION SWITCHES

Pron @ at

SWITCH AT BA SELF-TEST KEY LOOP (Game Pico) Swit i SWITCH AT D4

VOLUME CONTROL (Gare Fay) (To increase, POWER ONOFF swinct) SWITCH AT Pto/tt turn clockwise) (Special Options)

Game Switch Locations

Game options are preset at the factory and shown by the < symbols. However, you may change the ‘settings to suit your individual needs.

Game Price

This table contains the switch settings for options relating to game price, coin mechanism multipliers, and bonus play. The switches are on the game PCB at location 84 and are accessible when the game PCB is mounted in place.

The coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin,

The multipliers (toggles 446) determine how much each coin mechanism will be worth to the game's logic. The coin door has two mechanisms. To verify option switch settings, power the game off and then on again. Set the self-test switch to on and verify the settings on the self-test screen. Then set the self-test switch to off.

Options

The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. Therefore, if you have a2 OM/1 DM coin door, you may want to set the left multiplier at x2 and the Fight multiplier at x1.

You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players ‘who deposit four successive quarters, then press the start switch, can receive a bonus play. The bonus feature encourages players to insert more money than just the minimum $.25 required for one game All coins must be inserted before pressing the start switch.

Settings of 8-Toggle Switch on Gravitar PCB (at B4)

6531
874Option
OffOnFree play
OnOn1 coin for 2 credits
OfOff1 o0In for 1 credit
OnOff2 coins for 1 credit
onoffRight coin mechanism x1 <
OnOffRight coin mechanism x 4
OffOnRight coin mechanism x 5
OnOnRight coin mechanism x 6

® off ATARI '

ofofOff
OffOnOff
OnOnOff

Off Of = On

OnOffOn
OffOnOn
OnOnOn

Left coin mechanism x 1 << Left coin mechanism x 2 No bonus coins <4 For every 4 coins inserted, logic adds 1 more coin

For every 4 coins inserted, logic adds 2 more coins For every 5 coins inserted, logic adds 1 more coin For every 3 coins inserted, logic adds 1 more coin No bonus coins

No bonus coins

“<< Manufacturer's recommended settings

Special Options

Settings of 4-Toggle Switch on Gravitar PCB (at P10/11)

4321Option

On Credits counted on one coin counter. Off Credits counted on two separate coin counters