CATHODE RAY TOMES

ESwat

Cyber Police ESWAT (set 4, World) (FD1094 317-0130) (Sega, 1989) · Manual · 26 pages · 18 sections · original scan

Page 1

@ Installation/Owners Manual

420-0008U

Page 2

ESWAT Conversion

by:

@ SEGA Enterprises, Inc, (US.A.)

2149 Paragon Drive San Jose, California 95131 Phone Number (408) 435-0201 FAX Number (408) 435-0294

» AKit for. | :

Upright Cabinet with Horizontal Monitor

The Federal Communication Commission requires the verification of game . - kits. This game kit will meet these requirements when installed in accordance” with the instructions in this Manual and using only components and materials supplied with this kit.

Page 3

Table of Contents

Introduction 2.0. eee eee eee aeee I Handling and Installation Precautions ...................0..-- 1 Prevention of Counterfeiting and Conversion Labeling ............ I Precautions Concerning the Place of Installation ................ 1 System Requirements 2.0.00... 0.000 ccc ce cee eee ees 2 Tools Required 0... cece eee e ce eeeees 3 Cabinet Preparation .. 000.0 cee eee eens 3 Kit Component Verification... 2.2.00 0.00000. cece cece eee 4 installation Procedure «2... eee ee eee 5. Monitor Bezel ... 22.0... eee eee 5 License Seal .. 2... ee eee 5 Side Decal 2... ce ccc eee eee . 5 Marquee Plex... 2... 2... ee ee eee ee 5 Control Panel... ce eee eee eee 5 Service Switch Assembly .........0.2..00.0..0.0...0.2000- 6 Harness Installation ........0 0.0.0.0... 000 e cee cee eee 7 Interface Board Installation .......0....0... 20.0000. ee eae 8 Cabinet 115 VAC System Grounding ...................... 9 Cabinet System Checkout ............2.0.02.0 0.02 -0-00- 9 ESWAT Printed Circuit Board Installation .................. 9 Logic Board and Complete System Checkout ............... 9 In Case of Difficulty... 0... eee 11 Figured ee eee eee ees i3 Figure ce cee eee eee nae 14 Figure 3 cece cece eee eens 15 Figure4 2 ee eee eee ne 15° Figure 5 oe eee eee eee ee 16 Figure 6 20 eee cee eee ees 17 Figure Foo. cc ete eee 17 Figure Bo... cece eee 18 Figure? 20. ne eae 18 Figure 10 2.0... ccc eee ee cece ceeeeeees i8 Figure 1] ..... De eee ees eels meee ee seb wwe tet eee 19 Figure 12 ce ee eens 19 Figure 13. ee ee eee cece e eevee 20 Switch Setting Sheet .......0 0.000.002.0020 cece eee beeeeee 21 Schematic Diagram... 2. eee eee 22

Page 4

Introduction

SEGA ENTERPRISES, LTD., supported by its high electronic technology of . Large Scale Integration. microprocessors, etc. and a wealth of experience, has , for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S AND KIT INSTALLATION manual is intended to provide detailed comments together with all the neccessary information covering the operation and installation of electronic assemblies, electromechanical assemblies, control assemblies, and spare or replacement parts for the ESWAT coin operated game. This manual is intended for those who have knowledge of electricity and technical expertise in video games. Carefully “read the enclosed information before starting the kit installation or troubleshooting procedures.

Handling and Installation Precautions

During installation: = 1. Be sure to remove power plug when working on the machine.

  • Be sure all connections and harness routing are secure.
  • Make sure all grounding connections are secure and properly affixed.
  • Do not use any fuse that does not meet the specified rating.

Prevention of Counterfeiting and Conversion Labeling

‘ prevent counterfeit and unauthorized conversions, the following label is supplied with all authorized SEGA kit products. When handling such goods, be sure to locate and confirm the label. It is used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards.

ee nee ee eth fe aie ie ie lle aii aie le le all> lhe ler

Et 5g ee

Precautions Concerning the Place of Installation

The ESWAT CONVERSION KIT is intended to be installed in an indocr game cabinet. Absolutely do not install it outdoors. When installed indoors the following places mentioned below should be avoided to ensure proper operation and usage: Places subject to rain or water leakage, or condensation due te humidity In the proximity of an indoor swimming pool and/or shower Places subject to direct sunlight Places subject to heat sources from heating units, hot air, etc. Vicinity of highly flammable/volatile chemicals or hazardous materials Sloped surfaces Vicinity of antidisaster facilities such as fire exits and fire extinguishers Places subject to any type of violent impact Dusty environment

Page 5

Miscellaneous: i

+5 volts at 6 amps +12 volts at 2 amps Overvoltage protected at +5.8 volts Current limit set at 8 amps Input voltage 90 VAC to 135 VAC 60 Hz

  • If a switching power supply is used: « Current rating of 6 amps
  • Frequency attenuation of the following: 15 MHz -5 MHz 1.0 MHz 5.0 MHz 10.0 MHz 30.0 MHz 40db 65db 65db 55db 50db 50db
  • [fa linear power supply is used:
  • Current rating of 5 amps « Frequency attenuation of the following: «15 MHz 5 MHz 1.0 MHz 5.0 MHz 10.0 MHz 30.0 MHz

Line Fuse: Speaker: On/Off Switch: tsolation Transformer: Coin Door: Coin Meter. Power Cord: Color Monitor: édb 19db 28db 42db 45db ~ Sob @ 4 amp 120 VAC 8 ohms 10 watt 6 amp 120 VAC 115 VAC primary, 115 VAC secondary, 100 watts Dual coin acceptors +5 Voit DC Three conductor with ground

Video input | volt to 5 volt peak-to-peak positive polarity Sync TTL negative polarity separate horizontal and vertical Horizontal frequency 15.750 KHz Vertical frequency 60 Hz Video bandwidth 12MHz or greater Horizontal mounted Recommended size 19 inch

©

Page 6

Tools Required

Cabinet Preparation

Pwo

wn Drill Hole cutter 1-3/16* Phillips screw driver Flat blade screw driver Small flat blade screw driver Scissors Sand paper Paint X-acto knife Woed patch ene 2 @ © @ @ @ @ @

Remove oki PCB, and all existing game harnesses. Remove and disassemble the control panel. . Remove any side decals, moniter bezel, and marquee. Using sandpaper and/or paint thinner, clean and smooth the cabinet for paint preparation. Use wood patch to fill any knicks or flaws in the cabinet. . Paint cabinet if required. Wipe down and vacuum cabinet as necessary.

NOTE: You are building a new game, not just changing an old one. A nice, clean, and new Icoking conversion not only earns better, but lasts longer.
Page 7

oR Kit Component Verification ‘ Verify each component with the kit list provided to assure your kit is complete. If any part is missing after the inventory is taken, please contact your distributor,

  • and provide to them the following information: |. Kit serial number
  • Part number and description of missing item/s
  • Date received . Kit List Part Number Quantity Description
0002-00002#6 x 3/8 Phh Phil ek
0002-00014#6 x 3/4 P/H Phil “AB SMS
0312-00248#1024 x 1 3/4 Carr/Bolt Black
0502-00248#1024 Hexnut
0612-0024&#10 Split Lock Washer
0692-0024&#10 Flat Washer 1/2 OD
2112-00002Wire Nut #18 x 2
252-0006UIMonitor Bezel ESWAT
420-0008U]Manual ESWAT;
421-5801-102ILicense Seal ESWAT
4212-0001I(Kit) Serial # Sticker
423-0037U1ESWAT Marquee Plex
423-0045U2Side Decal, ESWAT
- 423-0038UiESWAT Control Panel! Overlay
423-0008-01IControl! Panel Clear Plex~
423-0035)1ESWAT Label Sheet (See List)) Py

(I) Test. Service, Volume Sticker {2} Joystick Stickers {2) Special Weapons Stickers

  • Jump Stickers :
  • Shoot Stickers {1} Start | Player Sticker (Ll) Start 2 Player Sticker
  • FCC Sticker (Kit}
4750-0049lVolume Control 100 Ohm 10 Watt
5090-50282PB Spst Switch Momentary
5091-0001-012Joy Stick 8 Way (Spring Type)
5091-0004-012PB Spst Control Panel (Red)
5091-0004-022PB Spst Control Panel (White]
5091-0004-032PB Spst Control Panel (Blue)
5091-0004-042PB Spst Control Pane! (Yellow)
6010-0043|Knob, ’s* Shaft
833-7164-02 °]ESWAT Game—PCB
9992-000064" Tie Wrap
KRO-I1721lService Switch Bracket
JAM-0000]JAMMA HARNESS
$25-0003U1Interface Board
5091-0015-018Pal Nut
5091-001 5-028Leaf Switch
5091-001 5-03&Universal Adaptor
S$25-0004U!Service Switch Hamess®
Page 8

r ) installation Procedure Monitor Bezel E.

+

License Seal 2.

Side Decal 3.

Marquee Plex 4.

Control Panel 5.

© :

12. “nT,

Locate MONITOR BEZEL (252-0006U). Measure the size of existing monitor bezel or the required size to fit and cut cardboard monitor bezel to size. (see figure 1)

Locate ESWAT LICENSE SEAL (421-5801-102) and place seal as shown of in figure I. Install Monitor Bezel on game cabinet. Note: Verify that the License Seal will be visible when the bezel is installed on game cabinet.

Locate ESWAT SIDE ART (423-0045U). Install on the left and right side panels of the cabinet {see figure 1). Note: A mixture of slightly soapy water can be used on the cabinet to position the artwork as desired. A squeegee may be used to remove any wrinkles in the artwork if scapy water is used.

Locate ESWAT MARQUEE PLEX (423-0037U). Measure the size of existing marquee plex or required size to fit and trim the marquee plex to size. Install on cabinet. (see figure 1}

Locate ESWAT CONTROL PANEL OVERLAY (423-0038U}. Measure the size required and cut the control panel overlay to fit the existing control panel.

Define the location of the player push buttons and joystick{s) on the contro] panel. (see figure 2)

Cut holes in control panel to locate buttons and joystick(s). See template

for button and joystick. (see figure 3)

Install the “ONE PLAYER START” label and the “TWO PLAYER START” labe] on the control panel overlay. isee figure 2}

install player control button labels, Special Weapons, Shoot and Jump on the control panel overlay. (see figure 2)

Install the JOYSTICK label(s} on the contro] panel overlay. {see figure 2)

Locate the CONTROL PANEL CLEAR PLEX (423-0008-01} and cut holes into the plex to match the holes cut into the control panel. Then trim as required to protect the contrel panel overlay and labels. Note: this clear plex overlay can be used to protect unused holes in the control panel from player punctures. (see figure 2) Install YELLOW buttons (5091-0004-04) in the “SPECIAL WEAPONS” locations. (see figure 2)

Install RED buttons (5091-0004-01) in the “SHOOT™ locations. (see figure 2)

wt

Page 9

Service Switch Assembly

  • Install BLUE buttons (5091-0004-03) in the “JUMP” locations. (see figure 2)
  • Install WHITE buttons (5091-0004-02) in | PLAYER START and 2? PLAYER START locations. (see figure 2)
NOTE: When buttons are securely placed and tightened in the control panel assembly, a small amount of clear RTV Silicone may be placed on two ox three areas of the lock-nut to keep the switches from being unscrewed from the top of the panel. (see figure 3)
  • Locate the JOYSTICK{S) (5091-0001-01). This Package consists of the following six components. a. Preassembled joystick(s) base assembly with microswitches . Exing c. Black knob & shaft d. 2" Dia. washer ©. Actuator plastic f. Pivot cone The final assembly of the joystick(s) must be performed after the joysticks) base assembly is mounted on the control panel. Locate the following: a. #10-24 X | 3/4 Carr/Bolt Black (0312-0024) (8 ea} b. #10-24 Hexnut (0502-0024) (8 ea) c. #10 Flat Washer 1/2" OD (0692-0024) (8 ea} d. #10 Split Lock Washer (0612-0024) - (Sea) Use the above components to secure the Joystick base assembly to the controi panel. (see figure 2)

The final assembly of the joystick(s) is performed by: a. Placing the 2* Dia. washer over the Black knob & shaft. b. Install the Pivot cone on the shaft. c. Install the Black knob & shaft assembly through the joystick{s} base assembly on the control panei. d. Install the Actuator micro/switch on the shaft. e. Install the E-+ing on the shaft to secure the assembly.

  • Locate SERVICE SWITCH BRACKET {KRO-1721)} and install two PUSH _ BUTTON SPST SWITCH MOMENTARY (5090-5028) into bracket as shown in figure 4.
  • Locate VOLUME CONTROL 100 OHM 10 WATT (4750-0049) and install into service switch bracket as shown in figure 4. . ;
  • Locate TEST. SERVICE, VOLUME STICKER and place on the service switch bracket as shown in figure 4.
Page 10

oR r . 20. Locate KNOB 1/8" SHAFT (6010-0043) and install on shaft of volume control 100 ohm i watt as shown in figure 4. Py 21. Install the Service Switch Assembly using 2 ea #6 x 3/8 PIH PHIL TEK screws (0002-0000) in the cabinet at either of the following locations {see figure 5):

  • On top of the steel enciesure for the Cash Box, inside the cain door.
Note: The TEK screws have a drill point and will drill through the steel enclosure. » Inside to the left of the coin docr, mounted to the wood cabinet.

Harness Installation = 22. Locate the JAMMA HARNESS (JAM-0000) and install as shown in figure 5. Use the provided (6 ea) 4" TIE WRAP (9992-0000) to secure the harness. ;

  • Connect the hamess te the POWER SUPPLY as follows: (see figure 6) a. +5 volt source. {Pins 3, 4, C, D of Jamma Harness} b. +12 volt source. {Pins 6, F of Jamma Harness) c. GND source. (Pins B, 27, e, 28, f of JAMMA HARNESS)
  • Connect the harness to the COIN DOOR as follows: (see figure 7.) a. Connect the wire to coin chute 2 acceptor microswitch COMMON terminal. (Pin T of Jamma) b. Connect the wire to coin chute 1 acceptor micreswitch COMMON terminal. (Pin 16 of Jamma) “a c. Connect the wire te coin chute 1 and 2 acceptor microswitch NOR-

r MALLY OPEN terminal. (Pin A of JAMMA)

d. Also connect Pin A JAMMA, to one side of each lamp on the coin door. e. Connect 4-5 valts from the power supply to the other side of each lamp on the coin door.

  • Connect the harness to the COIN METER by using two WIRE NUTS {2112-0000}. (see figure 8} Note: Some coin meters have an internal diode.
Page 11

oR r . 20. Locate KNOB 1/8" SHAFT (6010-0043) and install on shaft of volume control 100 ohm i watt as shown in figure 4. Py 21. Install the Service Switch Assembly using 2 ea #6 x 3/8 PIH PHIL TEK screws (0002-0000) in the cabinet at either of the following locations {see figure 5):

  • On top of the steel enciesure for the Cash Box, inside the cain door.
Note: The TEK screws have a drill point and will drill through the steel enclosure. » Inside to the left of the coin docr, mounted to the wood cabinet.

Harness Installation = 22. Locate the JAMMA HARNESS (JAM-0000) and install as shown in figure 5. Use the provided (6 ea) 4" TIE WRAP (9992-0000) to secure the harness. ;

  • Connect the hamess te the POWER SUPPLY as follows: (see figure 6) a. +5 volt source. {Pins 3, 4, C, D of Jamma Harness} b. +12 volt source. {Pins 6, F of Jamma Harness) c. GND source. (Pins B, 27, e, 28, f of JAMMA HARNESS)
  • Connect the harness to the COIN DOOR as follows: (see figure 7.) a. Connect the wire to coin chute 2 acceptor microswitch COMMON terminal. (Pin T of Jamma) b. Connect the wire to coin chute 1 acceptor micreswitch COMMON terminal. (Pin 16 of Jamma) “a c. Connect the wire te coin chute 1 and 2 acceptor microswitch NOR-

r MALLY OPEN terminal. (Pin A of JAMMA)

d. Also connect Pin A JAMMA, to one side of each lamp on the coin door. e. Connect 4-5 valts from the power supply to the other side of each lamp on the coin door.

  • Connect the harness to the COIN METER by using two WIRE NUTS {2112-0000}. (see figure 8} Note: Some coin meters have an internal diode.
Page 12

+

Interface Board Installation 26.

27.

28.

30. e Connect the hamess to the CONTROL PANEL as follows:

a. Route and connect the daisy chained wire to the terminal of the PLAYER PUSH BUTTONS and JOYSTICK as shown in figure 9. b. Connect the control panel hamess wires as follows: (figure 10)

[AMMA PIN # TO PLAYER 1 JOYSTICK UP 18 TO PLAYER | JOYSTICK DOWN 19 TO PLAYER i JOYSTICK RIGHT 21 TO PLAYER ! JOYSTICK LEFT 20 TO PLAYER 1 SHOOT 23 TO PLAYER I SPECIAL WEAPONS 22 TO PLAYER | JUMP 24 TO PLAYER | START 17 TO PLAYER 2 JOYSTICK DOWN Ww TO PLAYER 2 JOYSTICK UP ¥ TO PLAYER 2 JOYSTICK RIGHT . ¥ TO PLAYER 2 JOYSTICK LEFT x TO PLAYER 2 SHOOT ; a TO PLAVER 2 SPECIAL WEAPONS Zz TO PLAYER 2 JUMP - b TO PLAYER 2 START U

Connect the TV. Monitor as shown in figure 11,

Connect the routed speaker wires to the speaker. Check the routi ng for security. .

CAUTION!!: Do not connect the ESWAT PCB Direct to the Jamma Hamess as permanent, severe damage will occur to the PCB.

Locate the Sega to Jamma INTERFACE BOARD ($25-0003U ) and connect by inserting the card edge connector into the Jamma harness. (Note proper orientation figure 13).

Connect the SERVICE SWITCH HARNESS (S25-0004U) to the 9 pin con hector on the INTERFACE BOARD neti ng proper cnentation of connector. Route the SERVICE SWITCH HARNESS to the SERVICE SWITCH ASSY and connect as follows:

a. Connect the Service Switch Hamess Pin | to the ieft outside pin of the Volume Control 100 Chm 10 watt Rheostat (4750-0049). b. Connect the Service Switch Harness pin 2 to the right outside pin of the Volume Control 100. Ohm 10 watt Rheostat. c. Connect the Service Switch Harness Pin 4 to the center pin of the Volume Control 100 Ohm 10 watt Rheostat. d. Connect the Service Switch Harness pin 5 to one side of the “TEST” Momentary Push Button Switch (5090-5028). ©. Connect the Service Switch Harness pin 6 to the other side of the “TEST” Momentary Push Button Switch. : f. Connect the Service Switch Hamess pin 7 to one side of the “SERV. ICE” Momentary Push Button Switch (5090-5028). 0)» g. Connect the Service Switch Harness pin 8 to the other side of the fe “SERVICE” Momentary Push Button Switch.

Page 13

ee el

ge . is

Cabinet 115 VAC_3].Locate the GROUND lead (green) of the 115 volt input power Line [see

r System Grounding figure 12). This must be connected to all components of the

game system. This is a safety requirement for the players’ protection. This AC GROUND must be of #18 AWG wire cr larger. (see figure {2 for the proper routing of the wire] ;

Cabinet System Checkout 32. Apply power to cabinet system and check for the following voltages. If any voltage is incorrect. remove power and correct problem before proceeding any further. a. +5 Volts on pins 3.4.C, and D of the 56 pin PCB connector. (Interface Connector) b. +12 Volts on pins 5 and E of the 56 pin PCB connector. c. No voltage present on any other pins of the 56 pin PCB connector.

  • Check that the monitor has power. This can be accomplished by obserying the glow of the filament inside the neck of the picture tube.
  • Check that the Marquee lamp has power.
  • Check that the system ON/OFF switch functions properly.
WARNING: PROCEED ONLY IF THE ABOVE CHECKS ARE CORRECT
ESWAT Printed36.Connect the Logic PCB. to the INTERFACE BOARD by inserting the PC.B.

Circult Board installation edge connector into the 56 pin connector on the INTERFACE BOARD. e (NOTE: Proper orientation of each board is “Component Side Up")...

  • See the ESWAT SWITCH SETTING SHEET on page 21 of this manual. Place this sheet on the inside of the game so that it is visible when the back door is removed or opened. This will allow the DIP SWITCH OP- TIONS to be handy when service or changes in options are required.
  • Instail the logic PCB inside the cabinet (see figure 5}. Use (4 ea} #6 x 3/4 P/H PHIL “AB” SMS (0002-0001) to secure the PCB through its mounting feet.

NOFE: The proper orientation of the connector {see figure 13). If not connected properly, the system will not function and damage can occur to the PCB. ; ty

Logic Board and39.Apply power to the system and observe that the logic PCB functions. If a

Complete System Checkout video picture is not present proceed to “IN CASE OF DIFFICULTY” portion of this manual. When corrected, return to this pcint and continue.

Page 14

& 7

  • Press the TEST BUTTON te enter the test menu. Individual tests can be . entered by moving the Joystick. Press the test switch again to enter the ~ test : . * Memory test: ‘ ‘Tests all main program Rom and Ram accessible by the main CPU. ‘= input test: ‘Tests all player inputs.
  • Sound test: ‘Ests all sounds. Move the Joystick UP or DOWN to select Sound category and move RIGHT or LEFT to select individual sounds, Press AF
;sTACK to test.

© CRT test: . Displays color bar and grid size.so monitor adjustment can be made for color, focus, size, etc.

  • Dip switch test: Shows current Dip Switch settings. (Dip Switches may be changed in i this mode with power on.) . * Back-up RAM clear: Enables erasure of all bookeeping information, high scores, etc. « Exit: {Press test when arrow lines with this to exit to normal game mode.) Bookkeeping: Shows ail coin credit in data and displays high/low scores, etc.
  • Set up game options as shown in figure 14. ¢: | a. DIP SWITCH | on PCB sets up the number of coins per credit | b. DIP SWITCH 2 on PCB sets up the following:
1 Credit to Start- Set to ON-10N
|Advertise Sound- Set to ON-2 ON
|Game Difficulty- Set to NORMAL- 3.4.5.6, 7, 8 OFF
|42.Functionally test the game by:

} a. VERIFY that coin drops register proper credit/s and the COIN METER OPERATES. . , b. VERIFY that the proper number of lives is given for each CREDIT. c. VERIFY that the JOYSTICK MOVES the player left, right. and down, d. VERIFY that each SPECIAL WEAPONS BUTTON functions. ©. VERIFY that each JUMP BUTTON functions. f. VERIFY that each SHOOT BUTTON functions.

  • Locate the Kit SERLAL NUMBER STICKER and FCC STICKER. Install these stickers on the rear of the game cabinet. {see figure |}

CONVERSION IS COMPLETE | .

Page 15

In Case of Difficulty

No Raster/No Video . —Check A.C. line cord —Check line fuse —Check monitor brightness —Check power switch and/or interlock switch —Check all solder connections on fine filter and transformer —Check for proper orientation of the 56 pin PCB connector

’ Raster/No Video —Check all PCB to monitor connections —Check power supply voltage on PCB No Videof Game sounds can be heard —Check monitor brightness —Check all PCB to monitor connections

Incorrect colors —Monitor needs degaussing —Check for proper wiring between PCB and monitor —Check moniter adjustment and adjust if necessary

Wavy picture . ; —Check moniter ground is properly connected to monitor ~Be certain sync inputs are properly connected to moniter —Check horizontal hold adjustment

Yertical rollfHorizontal roll/Horizontal tear —Check horizontal and/or vertical hold adjustments —Check for proper wiring of sync from PCB to monitor, No sound —Check volume control potentiometer adjustment —Check for + 12 volts on edge connector of PCB —Check wiring from PCB to speaker —Check speaker for low resistance between the “+” and “—“ tabs

Bad sound _Check wiring to speaker for bad solder connections, —Check sound with another speaker No switch input Check ground connection te switch/es —Check wiring between PCB and switch/es for proper connection —Check switch/es with an ohmeter to verify proper operation

Switch operates incorrect function - . ~Check wiring between PCB and switches for proper orientation —Check wiring for shorts between switch inputs

Neo coin meter : —Check wiring to coin meter —Check that +5 voits is on "+" side of meter —Verify a +5 volt meter is used When coin switch is made and meter pulses. the screen blanks out and/or game resets —Verify that a meter with a diode is used ~If no diode is built in meter a 1N4004 can be used across the meter. Cathode to "+" side of meter and anode to “—” side of meter

Page 16

ILLUSTRATIONS

Page 17

JOY STKK ASSEMBLY

P DIA WASHER

FLAT WASHER

jurase—__| r RECOMMENDED PANEL LAYOUT

CUNTROL PANEL TOP VIEW

| PLAYER 1 START PLAYER 2 START ) SPECIAL WEAPONS SPECIAL WEAPONS: ~ 26 6 2 eo C 6o JUMP SHOOT JUMP OTS TICK

SUGGESTED LAYOUT “al HiILe SIZES (TOP VIEW? 276" 276" 158° | CeP START) | IP START) i CENTER A) fe E = MS< sHoor /— s CP wO¥ST 10S, 34 2e a JOYSTICK nook ump

Page 18

1.56"

, Figure 3 e

JAMIMA L TO SPEAKER TO S6Pb TO SPEAKER TO 56P 24

TG S6P 22 TO56P 23 ~

TO SEF f

ASSEMBLY AND WRC ON SWIOH BRACKET

@ _ Figure 4 SERVICE TSI VOLUME

Page 19

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 20

TERMINAL LAYOUT MAY BE DIFFERENT ON YOUR POWER SUPPLY

Figure 6

+ {0 Power surety +H

WIRING FOR COIN CHUTE DOOR iui

@ | Figure 7

Page 21

. “LA wee NUT

uel TO POWER SUPPLY +5V

em METER CND TO 56P 8 (Jamma)

WIRING FOR COIN METER T

Figure & 1!

CONTROL PANEL REAR VIEW

GROUND ROUTING

Figure 9

PLAYER 2 START SIGNAL ROUTING

Page 22

5.

COLOR

ua) |

Figure 11

  • N mm

Mi

a FLIER =| I)

WIRING OF AC LINE GROUND

LIGHT

Figure |2

Page 23

COO COOEOCOCL

Lt) C CAME BOARD —

COMPONENT SIDE TO SEGA PCB

: INTERFACE BOARD

_ TO JAMMA HARNESS

Page 24

+i COW METEA1 ONOF USED 1P SP WEAPON 1P SHOOT 1? UMP ONOT USED} 1P DOWN

1PUP +P RIGHT 1PLEFT (NOT LISED) INOT LISED) {HOT USED) IMOT USED) CONT

CON

TEST

_ SERVICE SPEAKER (+) cars s (NOT LISED}

COIMMETER 1 COM LOCKOUT 1 (NGT USED) COW METER 2 CON LOCKOUT 2

SPEAKER [-) AUDIOVGAND)

VIDEO GREEN

WIDEO SYMC

SERVICE

Ter SPEAMEA (+} MONITOR AUDED +} . VIDEO RED

VIDEO BLUE

vl HORIZONTAL en s COIN 1

1P STAT

1PUP 1P DOWN IPLEFT

IP RIGHT

1P PUSH 1

1P PUSH2

1° PUSHS

1P RESERVED

IP RESERVED

GND

GND a a MOSOOGODEOSOSO0000R0uo Ni

OF Se 171-5358

B-TYPE

O0

DIP Sw

DIP SW2

Switch Setting Sheet

Page 25

Sees rrazee emany-“"! to nt ‘aan eesti! H ; “aera-E- paket ae ewe A OZR OU

nae ADP aT See neserexer ey Wow’ .

AIHJeaLNT gas

LUMSS owvog ST W31S45 yas

Page 26

® |.) oe cos Lage! ag! ag rae oe SEGA TO JAMMA INTERFACE ADAPTOR.

TO SEGA PCB