CATHODE RAY TOMES

China Gate

China Gate (US) (Technos Japan (Taito / Romstar license), 1988) · Manual · 19 pages · 29 sections · original scan

Page 1

ROMSTAR ‘nc.

CHINAGATE"

INSTALLATION MANUAL

Romstar, Inc. 22857 Lockness Ave., Torrance, CA 90501 Phone (213) 539-2744 Fax (213) 539-3626

Licensed From Taito America Corp.

All Rights Reserved ©1988

Page 2

WARRANTY, REPAIR AND RETURN POLICY THIS POLICY WILL REMAIN IN EFFECT FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHSE FROM ROMSTAR. UPON EXPIRATION OF THIS ONE YEAR PERIOD, ROMSTAR WILL CONSIDER P.C.B. REPAIRS ON A BOARD—TO—BOARD BASIS, BUT IS NOT RESPONSIBLE FOR REPAIR OR REPLACEMENT.

  • *45 DAY FULL PARTS WARRANTY.

2 *60 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).

3, MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR

RETURNS.

  • ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS

WARRANTY.

(*ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR)

RETURN MERCHANDISE AUTHORIZATION — (RMA)

L ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.

2 ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #}.

3, ALL PC BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL BE

SUBJECT TO A MINIMUM CHARGE OF $40.00.

  • ROMSTAR WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.
  • ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WILL BE ISSUED.

6 ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY ROMSTAR WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).

  • FORANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.

ANY QUESTIONS CONCERNING THESE POLICIES SHOULD BE DIRECTED TO DENNIS SABLE, TECHNICAL MANAGER OR SHAWN ZENKER, OPERATIONS OFFICER.

Page 3

Installing Your

CHINAGATE

New Game Package

Table of Contents

New Gane Package Contents’ ys joven Meese Pe ReIA Tela bie aosys 60:9 bee. ale 04 oe ae 2 Power and’ Monitor Requirements, 2... cjejereresied soe sn ees nr ceesiecescseanscesenee Zi FeCtONYSELUNOS'. . . srremersiere ous xinkeisl ie RMON bes] 9.2 vslayers 06 syeueceropere wpvnarandle 3 Recommended Tools.and, SUpples vce came ttle yet Lilslelsic6i0.5 salelale Bhs vo diessld oles ob 6 a 4 [AStallation Procedures! <1, [Rane amen hice ee 5 teat us Sealers iis aif 5 COM Meter Diagram 5 ...-<4.cm soso rere em rpnet ure cers eisiatelery «ict viele Hie vind nerve oe old 10 MORICOF SYNC TDS...» . » i+: .ccgtaueee ter MRE eberetts et sts Sieve sucje'sys oyacermnersiiraee N COntral Panel: POsitionlag, ..<.SrepeeM rete ee etaesserelacets oles 45.6 sivlelsla.ere ole oigle-ciuloelell 12 DID SW DIAGF) j-co:t savewp vader nent ate erctetese here> cielacere onbMoysiecel iano afb dloalaiare oye 13 If’ Gase ORD RICHIEY, «1.2 Ae wnaretepeietet a eee Wlciajaareremnorfeo t0 os a <agse wb tur gubtlnigiee 14 Main! Harness: Connections... ci. vain sesitys sie ojerriererereinie 0.0 java inie 01 wooveresie 10 gine

Page 4

CHINAGATE NEW GAME PACKAGE CONTENTS

DESCRIPTION PART # || DESCRIPTION 1 Main Printed Circuit Board (PCB) 5501 || 4 White Player Button 1 Monitor Bezel 5508 || | Marquee 1 PCB Feet Assembly 0524 |! 1 Control Panel Overlay 1 Connecting Wire Harness (Jamma) 0215 1 Plex Control Cover 2 Eight-Way Joystick 0210 |} | Set Side Graphics 8 Player Button Assemblies 1 Set Play Instructions & Function Labels 2 Red Player Button 0229 1 Installation Manual 2 Blue Player Button 0233

Note: Replacement accessories available through your exclusive Romstar distributor

POWER REQUIREMENTS MONITOR REQUIREMENTS

7 amp minimum Horizontal Mount Raster Scan 1 amp minimum Negative Composite Sync | amp minimum

Page 5

ROMSTAR ‘inc.

Invites You To Use

OUR PHONE OR FAX NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER ROMSTAR GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS.

ROMSTAR, INC. 22857 LOCKNESS AVENUE * TORRANCE, CALIFORNIA 90501

TECH. DEPT. PHONE (213) 539-2744 FAX (213) 539-3626

  • FACTORY SETTING PLEASE SET THE CHINAGATE PCB AS FOLLOWS:

COIN 1 1 COIN —1 PLAY OFF /OFF/OFF COIN 2 1 COIN —1 PLAY OFF/OFF /OFF TV-SCREEN UPRIGHT ON DIFFICULTY NORMAL OFF /OFF DEMO SOUND NO SOUND ON

GAME TIME LITTLE BIT SHORT 55 ON/OFF # MEN 2 OFF/OFF

Page 6

Before You Get Started. . .Stop!

Does your new game package include all listed parts? (Is it complete?)

  • _Isthe game you have chosen to transform able to supply all the required voltages for the new game?
Note: Some games, (i.e. Ms. Pac Man, Galaxian, etc.) regulate their voltages on the main PC.B. This makes the existing power supply inefficient. These games will require a change in power supply for your new game. Many game supply houses can offer you a switching regulated power supply for a relatively low cost.
  • Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
  • Do you have the necessary tools? (See the recommended tool list)

Caution

F.C.C. Regulation Compliance Operation of this equipment in a residential area is likely to cause interference

  • in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4" © 7/16" Drill Bits 1/4” Plex Bit 1-3/16"” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw ; Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own Painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Nights Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” © 3/16" Masking Tape 3 1/2" OR 4" Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 7

Installation Procedures

Something To Think About

Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into anew game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is ... anew game ata very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of a new game package. The mew game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game

Remove the following:

1.Main logic board{s)4.Monitor Bezel
2.Control panel5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 8

Time To Install Your New Goodies

Before You Start. ..Remember DO NOT Do This Work With The Power On!

Logic P.C.B. Cage Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32"). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C __ Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.

Note: Leave the cage cover off until you have attached the entire wire harness and have tested the game for proper operation.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Page 9

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. ..CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires

Connect the designated wires to the coin switches and meter.

  • Youcan connect your door lamps to the unused -5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the contro! panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. W/hen you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, board cage, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Page 10

Time to Apply Power:

  • Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED)
  • Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board
NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker.
  • How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative). If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one I.C. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs.

HORIZONTAL SYNC INPUT FROM P.C.B. S vec (OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR

NOT USED

GROUND

B) Now how's your picture? © It it centered?

  • Is it too bright or dim? Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Dip switch 2 on switch bank A should solve your problems.
Page 11

Control Panel Assembly

1.

2. Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We fee! that yournew game investment is well worth protecting. . .and the control panel is the first Place to show wear and tear.

  • You will need to cut this piece to size. Use the control panel as a template. ¢ Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass pane! protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, piace the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easter: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel. Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time ... Don’t forget this is going to be anew game.

Page 12

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc.

  • Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet).
  • Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing.
  • Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

  • Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.
  • Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can't get a coin into it.
  • Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking.
  • Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . Are all the player controls working? Are the game sounds present? Is the volume level proper? __* Are tne dip switches-set properly? Well, that’s about it. Good Luck.

Coin Meter Diagram

To attach a coin meter, use following diagram:

+5VDC +12VDC METER or +24VDC f i

DIODE (IN4004)

COIN SWITCH TO MAIN HARNESS COIN ° OR COIN DIODE (IN4004) COUNTER

  • OUTPUT SWITCH GROUND
Page 13

Star Tech Tips We are grateful to Star Tech Journal for allowing us to publish the following excerpts from their ‘journal.

  • Monitor Sync Ifyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going. CURE 1: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two Power pins so that they are parallel to the top surface of the new !.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.) HORIZONTAL SYNC INPUT FROM PCB. 5. Vcc SVOC (PIN 14) {OR COMPOSITE SYNC INPUT) SOLDER TO. HORIZONTAL SYNC OUTPUT TO MONITOR EXISTING CHIP (OR COMPOSITE SYNC OUTPUT)
  • VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR

FIG.2

GND |PIN 7)

FIG.1

CURE 2: Used for Wells-Gardner Video-Sync boards with Positive sync connections only. (Vertical mount board 85x140B. -

Cut the traces on the solder side of the board between input pins 5 & 6to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a IN4148 diode - cathode to the emitter of the MPSAS6 and anode to the base. (See Fig. 3) RED] © GREEN2 © BLUE & GND4 © FIG.3 VERES HORIZ 6 2201

CUT TRACES — at MPSAS6

IN4148

Page 14
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.

IN4148 NEG: SYNC INPUT

To Ov Orano FIG.4 2 1 GND BLUE GREEN RED = = = OH ViOhm@m-O: OF 6 5 4 3 2 1

IN4148

CURE 3; Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from \W/102 to either J2 or J3. CURE 3: For Wells-Gardner K4600 series monitors Replace C356 (4 7uf 25V) on the Horizontal (vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.

Control Panel Positioning

2P 8-WAY 1.P

ATTACK

JUMP

ce] 1 PLAYER 2 PLAYER

Page 15

DIP SWATCH SETTINGS

DIP SWITCH 1

w * Al ee '* Coln-1 A S 1 Coin—1 Play 1 Coin — 2 Plays 1 Coin — 3 Plays 1 Coin — 4 Plays 1 Coin — 5 Plays 2 Coins — 1 Play 3 Coins — | Play 29/2) 9/2/9/219 2/2} Q19/219/919 J/2/ 2/2) 9/39/19 4 Coins — I Play

  • Coln-2 S___1Coin—1 Play 1 Coin — 2 Plays 1 Coin — 3 Plays 1 Coin — 4 Plays 1 Coin — 5 Plays 2 Coins — 1 Play 3 Coins — 1 Play 9|219/9/ 212/913 9} 2/2/2/F/91919 4 Coins — | Play
  • TVSCREEN Table type use A S Upright type use
  • Screen Invert Normat ig Invert
  • Degree of Difficulty OFF A $ ‘Normal OFF Easy Not too easy ON Difficult
  • Sound for Demonstration OFF _| A ‘Sound s No Sound
  • Game Time Normal 60 : Long 70 A Little Bit Short 55 g}2/$/9 219/218 Short SO
  • Number of Characters A Ss ra 212/919 ad =| elu

‘S = STREET LOC.

Page 16

CHECKPOINTS IN CASE OF DIFFICULTY PROBLEM / CAUSE-CURE No Raster/No Video

  • Check A.C. line cord ~ Check line fuse
  • Check monitor brightness
  • Check power switch and/or interlock switch ~ Check all solder connections on line filter and transformer
  • Check for proper orientation of the PCB connector

Raster/No Video

  • Check all PCB to monitor connections
  • Check power supply voltage on PCB

No Video/Game sounds can be heard ~ Check monitor brightness

  • Check all PCB to monitor connections

Wrong colors ~ Monitor needs degaussing

  • Check for proper wiring between PCB and monitor
  • Check monitor adjustment and adjust if necessary

Wavy picture

  • Check monitor ground is properly connected to monitor
  • Be certain sync inputs are properly connected to monitor
  • Check horizontal hold adjustment

Horizontal/Vertical Roll

  • Check horizontal and/or vertical hold adjustments
  • Check for proper wiring of sync from PCB to monitor

No sound

  • Check for -5 volts on edge connector of PCB ~ Check volume control potentiometer adjustment ~ Check for +12 volts on edge connector of PCB ~- Check wiring from PCB to speaker ~- Check speaker for low resistance between the “+” and “-" tabs

Bad sound ~ Check wiring to speaker for bad solder connections

  • Check sound with another speaker

No switch input

  • Check ground connection to switch/es
  • Check wiring between PCB and switch/es for proper connection
  • Check switch/es with an ohmmeter to verify proper operation

Switch operates incorrect function ~ Check wiring between PCB and switches for proper orientation

  • Check wiring for shorts between switch inputs

No coin meter

  • Check wiring to coin meter
  • Check that +5 volts is on “+” side of meter
  • Verify a +5 volt meter is used

When coin switch is made and meter pulses, the screen blanks out and/or game resets

  • Verify that a meter with a diode is used ~ If no diode is built in meter a IN4004 can be used across the meter. Cathode to +” side of meter and anode to “-” side of meter
Page 17

ROMSTAR JAMMA HARNESS PLEASE REFER TO MAIN HARNESS

VERSIONS 1 - 4 PIN-OUT FOR PINS Z, a, b, 22, 23, & 24.

JAMMA GE.BK JAMMA CA.BLU

+5VDC +5VDC +5VDC +5VDC +5VDC +5VDC +5VDC

+5VDC +12VDC

Post

Red Coin Counter 2

Coin Lockout

Black Speaker (-)

N/A Green Video Green White Video SYNC comeing) Pink Service Switch Yellow Tilt Switch Orange Coin 2 Gray 2P Start Green 2P Up Blue 2P Down Violet 2P Left Yellow 2P Right

Red Orange +12VDC

Coin Counter 1

Speaker (+) N/A Video Red Video Blue Video Ground Test Switch Coin 1 IP Start Brown IP Up Green IP Down Blue IP Left Violet IP Right Yellow Red Orange +12VDC

Coin Counter 1

Speaker (+) N/A Video Red Video Blue Video Ground N/A Coin IP Start Gray IP Up Violet 1P Down Blue IP Left Green IP Right Yellow Orange Red Brown N/A Blue N/A Blue Ground Black Ground Black

+12VDC

Coin Counter 2

Speaker (-) N/A Video Green Video SYNC jcompmesi N/A N/A SRVC Switch 2P Start 2P Up 2P Down 2P Left 2P Right

IN [le [inf ola lo C[msUlOlwiulri[ralx |a[S]Z Jo |e ju |r [D> |S Se

N/A N/A Ground Ground Wire color / Stripe color Wire color/Stripe color

N/A N/A Ground Ground N/A N/A Ground Ground

Clm/UlOlwiul/ria}s< }a}S/2 Jo [a Ju |e JD ]> |B |x |> IN| wlaolulo] ele >|N{wlolulole |

NOTE: Please refer to manual harness pinout for pins
Page 18

JAMMA DA.BK JAMMA SK.GR

Red Red

White

Yellow

Red Red

Red Red

Green

Brown/White | Coin Counter 2 Red/Black Coin Lockout White/Black Speaker (-) T Coin Counter 1 Bm/Wht Coin Lockout Red/Blk Speaker (+) White Coin Counter 2 Coin Lockout Speaker (-) Ground Light Green Video Green Gray/White | Video Sync icorones: Coin Counter 1 Brown

Coin Lockout Speaker (+) White

Audio Video Red Pink Video Blue Sky Blue Video Ground Black N/A Orange Coin Violet/White IP Start | Black/White IP Up Brown/White IP Down Red/White IP Left Orange/White IP Right Yellow/White Green/White Blue/White

HIN|[ mle ]mloln|alo

IN] {e}inloln}aolo

Green Video Green Gray Video SYNC compres Red/Bik Service Switch Tilt Switch Wht/Bik Coin 2 Wht/Gry 2P Start Wht/Vio 2P Up Wht/Blu 2P Down Wht/Gm 2P Left Whr/Yel 2P Right

Wht/Ora ‘Wht/Red Video Red Red Video Blue Blue Video Ground Black Test Switch Brown Coin 1 White IP Start Gray 1P Up Violet IP Down Blue IP Left Green IP Right Yellow Orange Red Brown Blu/Wht Red/Wht Ground Black Ground Black Wire color / Stripe color Wire color/Stripe color Violet Service Switch Gray N/A +: Coin 2 Wht/Bik 2P Start Brown/Black 2P Up Red/Bik 2P Down Orange/Biack 2P Left Yellow/Black 2P Right Green/Black Blue/Black

al, <lmfUlofwlu}ri[r{x|o}S]Z lo a ju |r |D]> |B x |>|N] wlaolvlo]el- N/A N/A Ground Ground N/A NA Ground Ground

<lalUlolwiulr[afx}o}S/Z Jo fa jo |r JD ]> |B |x ]> [IN| wlolulolel—

NOTE: Please refer to manual harness pinout for pins
Page 19

Black JAMMA Hamess — Da. 1 CUINAGATE

Solder Side Ground Ground Red +5VDC Red White Yellow +12VDC Post Brn/Wht Coin Counter 2 Red/Blk Coin Lockout Wht/Blk Speaker (-) Ground Ground +5VDC soc | -5VDC White +12VDC Yellow Post —

Coin Counter 1 Brn/Wht Coin Lockout Red/Blk Speaker (+) White Ol OINIO) Wm) el win] —

Video Red Red Video Blue Blue

Video Ground Black

Brown Video Green

Video SYNC (compra) Red/Blk Service Switch

Coin 1 IP Start IP Up Violet Down | —_—éBlue IP Left Green IP Right Yellow 1 P ATTACK Orange 1 P JUMP Red 1 P MAGIC P. Brown Blu/Wht Red/Wht Ground Black Ground Black Wht/BIk Coin 2 2P Start

2P Up Wht/Blu 2P Down Wht/Grn 2? Left Wht/Yel 2P Right Wht/Ora 2P ATTACK Wht/Red 2P JUMP Wht/Bm 2P MAGIC P. Gm/Wht Yel/Wht Black Black Wire color/Stripe color >| alala}ola|N| «|x| €}<] Cl} alu) a} 2} 2) eS} er] xa] e} zr] a} m/ ola) a] >