CATHODE RAY TOMES

Hammerhead

Hammerhead (Innovative Concepts in Entertainment Inc.) · Document · 23 pages · 36 sections · original scan

Page 1

OWNERS AND SERVICE MANUAL

INNOVATIVE CONCEPTS IN ENTERTAINMENT INC. 10123 MAIN STREET, CLARENCE, NY 14031 SERVICE: 1-716-759-0360 FAX: 1-716-759-0884 E-MAIL: service@icegame.com

Page 2

TABLE OF CONTENTS

INTRODUCTION |... esses eeesssteesseeesseeeesees PAGE 3

GAME FEATURES GAME PLAY

INSTALLATION... cecscetseecesenesesserssesesersneenes PAGE 4

BEFORE YOU BEGIN INSTALLATION

PROGRAMMING OPTIONS .........:ececeeereeeees PAGE 5 & 6

INTRODUCTION USING THE PROGRAMMING OPTIONS

MAINTENANCE ..........0..00e es eeseee cesses eerste eeeeees PAGE 7

QUICK TROUBLESHOOTING .......... eee PAGE 8

GAME REPAIR.............0:cceceeseeee cesses eee eeeeeeeeees PAGE 9 - 11

OPERATIONAL BACKGROUND TROUBLESHOOTING PHILOSOPHY MECHANICAL REPAIR

PARTS LISTINGS |... eee ee ee eee teres PAGE 12

SCHEMATICS... eee eee cette ceeeeeeneeees PAGE 13-15

WIRING DIAGRAMS .......... 0. eee eee PAGE 16-25

Page 3

INTRODUCTION

GAME FEATURES

Thank you for purchasing the new Hammerhead" game from I.C.E. This new “WACKY” game utilizes all the proven technology of it’s predecessor Smack-n—Alien. ICE has taken out the cost but not the quality, giving the customer a fresh look with full reliability.

Game cabinetry is stylish, yet bright. The game has been designed to be either a back-to-back centerpiece or a wall unit that will enhance the look of any location. Thick 16 gauge metal panels and marine grade water resistant plywood make the game extremely durable. The boat bow is made of a special high impact styrene that is easy to maintain. The distortion printed marquee is made of .187 PETG. This is back printed, which will prevent the customer from damaging the printing. The PETG is more durable than acrylic and therefore will withstand impact better. Electronics and sounds are the state of the art in digital technology. Robust design ensures a long trouble free life for your game. The game is very flexible with its programming options to allow it to be tailored to most locations easily.

GAME PLAY

The object of the game is to hit as many sharks as possible in the time allowed. (Note: the player must try to hit the sharks that are in the up position to score points) The player does not get penalized for missing a shark. The high score for the day will be displayed for all new players to try and match.

(NOTE: There is a bonus shark, the shark that pops up before game play starts. If a player hits that on he will be awarded one extra point.)

Page 4

INSTALLATION

BEFORE YOU BEGIN

WARNING: WHEN INSTALLING THIS GAME, A

GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USEA GROUNDED RECEPTACLE COULDALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WARRANTY.

HAVE A QUALIFIED ELECTRICIAN CHECK YOU'RE A.C. RECEPTACLE TO BE SURE THE GROUND IS FUNCTIONING PROPERLY.

TOOLS NEEDED

The game normally comes fully assembled and ready for use.

If however, you need to disassemble or reassemble the marquee to the game for any reason, all that is needed is a 5/32 security Allen wrench.

The game comes ready to play with just a few simple things to keep in mind.

  • When installing the game, be sure you use a grounded A.C. outlet. If necessary, have it checked to be sure the ground is good.

THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE.

Make sure the game is level after installation. It is necessary to make sure the game is level so the game will work properly.

Place the game into its final location and use the adjusting

CAUTION: CHECK THAT THE A.C. VOLTAGE RATING ON THE BACK OF THE GAME MATCHES THE A.C. VOLTAGE OF YOUR LOCATION.

THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE.

TO OPERATE THE GAME AT VOLTAGES OTHER THAN THOSE IT WAS DESIGNED FOR, PLEASE CONTACT OUR SERVICE DEPARTMENT FOR VOLTAGE CONVERSION INFORMATION.

Plug the game into the A.C. outlet and turn on power to the game. The switch for the game is located on a power module on the outside rear of the game.

It is now time to program your game&&..

Page 5

PROGRAMMING

INTRODUCTION

The Hammerhead" game is extremely flexible from a programming standpoint. This allows the customer to “fine tune” the game to his or her exact needs.

This section will describe in detail each of the programming options and how they work.

PLEASE READ THIS SECTION THOROUGHLY BEFORE CALLING OUR SERVICE DEPARTMENT. MOST QUESTIONS. REGARDING SET-UP AND OPERATION WILL BE FULLY EXPLAINED HERE.

HOW TO USE THE PROGRAMMING OPTIONS

PROGRAMMING BUTTON - Use this button to enter and exit the programming mode. Press this button once to enter the mode, and once again to exit the mode.

SELECT BUTTON - Use this button to scroll through and “step” through the various options.

ADVANCE BUTTON - Use this button to “change” the value of a particular option.

TICKET RESET BUTTON - Use this button to “reset” ticket counter.

PROGRAMMING BUTTON

SELECT BUTTON

ADVANCE BUTTON ma

Page 6

OPTION DEFAULT

PROGRAMMING

MIN / MAX DEFINITION

Volume adjustment

coins per credit switch 1

# of coin 1’s per credit switch 2 number of seconds per game

difficulty (lower = easier)

tickets just for playing

hits per tickets

ticket cap per game

minutes between attract mode

attract mode type

factory reset

NOTE: After the factory reset has been selected, the programming button must be pressed twice to exit.
Page 7

MAINTENANCE

GENERAL MAINTENANCE

This game has been designed to be as trouble and maintenance free as possible.

With this in mind the only basics are to keep the game clean. Below are the main areas to take care of with specific directions.

MARQUEE

The MARQUEE should be cleaned with a soapy water solution if covered with water-based dirt such as food products. After cleaning with soapy water, polish with a commercial plastic polish or a spray furniture polish. These have lubricating oils that condition the plastic and keep it shiny and clear looking. Never use regular glass cleaners as the ammonia in them actually damages the plastic and dulls it.

Any deep scratches can be reduced or eliminated with a scratch removing polish and buffing wheel.

CABINET

The cabinet plastic and decals can be cleaned with soapy water or spray furniture polish. DO NOT use any alcohol or petroleum based cleaners as they could damage the plastic or printed parts.

COIN MECHANISMS

The coin mechanisms should be cleaned periodically, as they will accumulate dirt, which will cause the coins to stick.

Remove the coin mech and clean them in a dish detergent solution and a stiff brush. Dry thoroughly and re-install.

TICKET DISPENSERS

The biggest problem ticket dispensers have is ticket dust blocking the optical detectors. It is a good idea to occasionally use compressed air to remove the dust from the dispensers.

SHARK HEAD

The sharks should be cleaned with a soapy water solution. Be sure to wring the sponge out before cleaning. Excess water may drip onto coil bed assembly and cause permanent damage.

LUBRICATION

We do not recommend the use of any lubrication anywhere on the game.

The only moving parts on the game are the sharks. If you notice any sticking or binding of the sharks check the following.

  • Dirt on the solenoid shafts - Remove the solenoid shafts, clean with isopropyl alcohol. Finish wiping clean with a good grade of spray polish only.
  • Wear - If excessive solenoid body wear is noted, replace the solenoid coil.
Page 8

QUICK TROUBLESHOOTING

GAME WILL NOT TAKE OR ADD MONEY CORRECTLY + Micro switch not working or returning properly. Check and repair or replace as necessary.

  • Bad Harnessing or connector. Check w/ohm meter and repair as necessary.
  • Game programming set incorrectly. Check programming option and re-program if necessary. Bad Main P.C. Board. Check and repair or replace as necessary.

SHARKS WILL NOT POP UP DURING GAME PLAY

  • Opto Sensor is not working properly. Test and replace as necessary.
  • — Reflective foil is not properly in place. Reapply foil correctly. + Bad harnessing or connector. Check w/ohm meter and repair as necessary. + Bad Main P.C. Board. Check and repair or replace as necessary.

GAME HAS NO SOUND + Bad speaker. Check w/ohm meter for 4 or 8—ohm load. If not within this range, replace. + Volume level set incorrectly. Check volume level in programming, and adjust if necessary. + Bad Harnessing or connector. Check w/ohm meter and repair as necessary. + Bad Main P.C. Board. Check and repair or replace as necessary

TICKET DISPENSER DOES NOT WORK OR WORKS IMPROPERLY

  • Bad ticket dispenser. Repair or replace as necessary. Bad harnessing or connector. Check w/ohm meter and repair as necessary. Bad Main P.C. Board. Check and repair or replace as necessary. Game out of tickets. Add tickets Optical sensor on ticket dispenser dirty. Remove paper fuzz and debris with a soft brush.

NO FLORESCENT LIGHTING

  • Bulb burned out. Replace bulb. + Electronic ballast bad. Replace ballast. + Harness bad or harness unplugged. Check w/ohm meter and plug in, repair or replace as necessary. + NoA.C. power to the game or Main fuse bad. Check fuse and A.C. power.

TICKETS OR HIGH SCORE DISPLAY Don’t WORK PROPERLY + Bad Display P.C. Board. Repair or replace Display board

  • Bad Main P.C. Board. Repair or replace Main board. + Bad display harnessing. Repair as necessary.

CAN’T ENTER OR EXIT PROGRAMMING OR OTHER ADJUSTMENT MODES + Bad programming or adjustment buttons. Replace buttons. Check harnessing.

  • Bad Main P.C. Board. Repair or replace Main board.
Page 9

GAME REPAIR

WARNING: ALWAYS REMOVE POWER TO

THE GAME BEFORE ATTEMPTING ANY

SERVICE, UNLESS NEEDED FOR SPECIFIC TESTING FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.

OPERATIONAL BACKGROUND

The HAMMERHEAD" game has been manufactured with modular design in mind. Almost everything in the game can be EASILY removed for servicing. This makes it much easier for the repairman as he / she can work in a quieter less distracting environment away from the Game Room floor. The game relies on 1 coil bed assembly which can be remove from the game very easily.

Coin and low ticket sensing are done with conventional micro switches. In all areas of critical importance, optical sensors were developed specifically, and optimized for their particular application.

All P.C. Boards are made of premium quality board material and use time proven components to assure you of the most reliable designs possible.

We have put forth our best efforts and tested this game extensively to assure the best possible performance under the widest variety of operating conditions. We are ALWAYS however interested in our customers input for product improvement. If you have any questions or comments please feel free to contact our service department.

|.C.E. SERVICE DEPARTMENT 716-759-0360

NORMAL BUSINESS HOURS ARE:

MONDAY - FRIDAY, 8:00 AM TO 5:00 PM

TROUBLESHOOTING PHILOSOPHY

To find problems with the game, always first check what should be obvious. See that the game is plugged in, and that all of the fuses on the game are good. This includes the fuse that is located INSIDE the power module.

Next, check to see that all of the connectors are firmly seated and that none of the wires have been pulled out of them.

When trying to find out if specific components are bad or not. This will help you to know if you have a problem with a specific component, or maybe a problem with either the wiring or the Main P.C. Board.

Use extreme caution when using probes or voltmeters if the game is powered up. If doing continuity checks, it is important to disconnect the harnessing at both ends, as attached they may yield erroneous results.

If a P.C. Board is suspected as the cause of a problem, check to see that all of the components on the board are firmly attached. Pay special attention to any socketed devices.

If light bulbs are suspected, swap them with a bulb that is known to work to narrow the problem down to either a bulb or P.C. Board.

Page 10

GAME REPAIR

REPLACEMENT & REPAIR COIL BED PARTS REPLACEMENT

Service the coil bed as follows: COIL BED SERVICING Remove all the shark heads from the coil bed. To To remove the coil bed: remove sharks, turn the coil bed over so that the coil bed is resting on the shark heads. Remove

  • Remove the 4 bolts that hold the boat bow on to the Allen head screw from the shaft. Cut the wire the cabinet. The bolts are located on the tie and remove the locking pin. Pull the shark underside of the playfield, on the left & right sides heads through the coil bed. of the game. a

CUT WIRE TIE & REMOVE PIN = = ¥ 5

= Unplug the Sensor PCB Assembly. Remove the two

  • Remove the 6 bolts holding the coil bed in Nylok nuts holding the coil cap. position as shown in the photo below.

NE Disconnect the wires to the coil & remove. Assemble in reverse order.

Page 11

GAME REPAIR

MARQUEE BULB / DISPLAY BOARD SERVICE

To replace a light bulb:

Remove the square drive screws on the rear of the marquee, that attach the lamp mounting panels. Start with the side that looks like the light is out.

/ ae Display Board follow the directions below:

CAUTION: Be sure that the power has been disconnected before attempting to unplug the Display Boards.

Remove the security Allen bolts around the perimeter of the marquee. Using a Phillips screwdriver, remove the four screws that hold the board in place.

‘ Fl aa-~

Repeat the previous steps to remove the second display.

IF YOU HAVE ANY QUESTIONS OR COMMENTS, PLEASE CONTACT OUR SERVICE DEPARTMENT AT:

716-759-0360 MON. THRU FRI. 8AM-5PM EST

Page 12

PARTS LISTING

Parts denoted with * indicate available as part of ELECTRONIC / ELECTRICAL a specially discounted spares kit.

WS2034X Main PCB

WS2032X Display Boards

MECHANICAL PARTS 2205 Fuse, MDQ6 (6 Amp Slo Blo)

2315 Fuse, MDQ3 (3 Amp Slo Blo)

an Low Ticket Micro Switch Bw250X PLL Bulb Socket Assembly FP1004 Leg Leveler Mounting Bracket HR1019 Leveler Foot

1024Ticket BinDECALSANDGRAPHI

1026 Bracket, Low Ticket Switch Mounting C. Ss G cs

AR2007 Speaker, 6” x 9” Bw2017 PLL Bulb Retaining Clip

Bw2018PLL Bulb SupportWS7003BOAT DECK DECAL

WS7005 FRONT DECAL

pasFan, DO12NoltWS7112RIGHT SIDE DECAL

CC2027 Power Cord, 20 ft. WS7110 LEFT SIDE DECAL

5101XMech Holder Assemblyws7027MARQUEE (BACK DROP
BW8284XWorkhorse 6 Ballast, (WH6—120-L)Wasicetoao ()

8312" Bulb, PL-L 40W/41/RS/IS Fluorescent

HH5005 Ticket Dispenser WS4011 Shark Head

WA4010 Mallet

175 Immonex Mech. 1026 Low Ticket Switch 2289 Reset Button 8212 Flashing LED (Low Ticket) CG2027 Power Cord 9’ 2364 Coil Bed Fan WA1054 Limiting Pin 8312 Light Bulb MZ8284X —_—_ Ballast Workhorse 6 WS7027X Marquee Vacuum Form WS3004 Boat Cleat

WS8444xX = Jewel Light Assembly WSg9001 Service Manual

WS2011X Shark Head Assembly

Page 13

4 3 2 1

P2 PI keY | 10 [KEY KEY | 10 | key

To Display BoardGround|g[BLACKBLACK | 9 | GroundTo Display Board

BLACK BLACK

Ground|88 | Ground

KEY KEY

SX]Z Porownieaprownired] 2 | Ko
peik|6[brownierownlred]& | DCLK
DATA)8Srown/ahie‘prowntinie]© | © DATA
DLATCH]|4ORANGEORANGE4 | DLATCH
12 VDC|33 | 12 VDC

ORANGE ORANGE

12 VDC|2KEY2 | 12 VDC
keY|7[KEYKEY 4 | KEY

10 PIN AMP HOUSING #2291 CONTACT PIN #2201 PINS 1, 7, AND 10: KEY PLUG #2239 10 PIN AMP HOUSING #2291 CONTACT PIN #2201 PINS 1, 7, AND 10: KEY PLUG #2239

Tme HAMMERHEAD pescnprion #W'S2051AX - DISPLAY PLENAME: _WS.VSD INTERCONNECT HARNESS Peaey MARTIN

DATE7/9/01REVISED8/15/01PAGE10F 10

4 3 2 1

Page 14

4 1

To Main Board Pt

Po KEY a KEY | 40] Key Ground | 1 [BLACK BLACK | 9 | Ground BLACK BLACK Ground | 2 8 | Ground KEY KEY KEY| 3 Porownvred brownired] 2 | KEY pata | 2 [prownigreen Brownigreen] 6 | PCLK To Display Board Brown/white Browniwhite DLATCH | 6 4 | DLATCH ORANGE ORANGE 12 voc | 7 | ORANGE CANGE] 3 | 12 voc 12 voc | 8 New| 2 | 12v0C L ev | Key 8 PIN AMP HOUSING #2405 CONTACT PIN #2201 PINS: KEY PLUG #2239 10 PIN AMP HOUSING #2291 CONTACT PIN #2201 PINS 1, 7, AND 10: KEY PLUG #2239,

TITLE HAMMERHEAD:

DESCRIPTION #WS2051X - DISPLAY HARNESS. FILENAME WS.VSD.

DRAWN BY MMARTIN

DATE 7/9/01 REVISED 8/15/01 PAGE 20F 10

Page 15

4 2 1

#650 a sso SiH Feser pa 110 “ bes ADV ‘oo LH [72d 110

To Mainboard P7 39" #650

PTTicket Reset | 1[vislevbrownviolet/orownPAA 10 =x.
Program | 2 [Wvidletred_violet/redoz #050
Select | 3 [vidlevorangeViolevorangeJA s10
Advance | 4 violet/yellowviolet/yellow4

Ground | 5 black black #650 #27145 PIN IDC ho ah PRG "10

TM HAMMERHEAD

pesoniprion # WS2052X - PROGRAMMING cee WS.VSD HARNESS DRAWNBY — MMARTIN

DATE7/9/01REVISED8/15/01PAGE3 OF 10

4 2 1

Page 16

Jewel 6| Jewel 5| Jewel 3| Jewel 2|

Jewel 1

187 187

#6514651 #20097), p#2909 #290971 #2909 #2909, 187 187.187 & Jewel 4|

#2909 zh ean yen ean rane sang agen

#651 651 ser pp ser #6517 651 #651 #651 #651 eS1 #651 #651 iad aii iad aii a “ye wae

Jewel Al

Jewel G

Jewel Dj

Jewel &| Jewel F|

#29097 #2909 #2909) 187 187.187

#651 #651 #651 187 ” oY f Jewel B|

#651 y#2009 #2909;

{ #651 #651 #651 #651 #651 #651 ine san yon sane ine ame gre

#651 651 i ‘87 a ‘er pier sin “9

Jewel 1 4 [white/brown Jewel 2] | 2 [white/red Jewel 3| | 3 | White/orange Sewel 4| | 4 [white/vellow ‘Jewel 5| | 5 | White/areen Jewel 6 6 white/blue cae ——— 12 VDC 8 rena’ FILENAME WS.VSD ewes . DESCRIPTION #WS2053X - JEWEL LIGHT HARNESS DRAWNBY — MMARTIN 9 PIN PLUG #2292 ‘SPLIT PIN #2100 = = _ — ewe 4 3

Page 17

To Main Board

Right Speaker - Right Speaker +

Left Speaker - Left Speaker + To Right Speaker brown/white oq #659T

#6537 250 + red/white

P41 7 | brown/white > [tediwhite

4 [brown/gray 5 [tedaray 5 PIN AMP HOUSING #2419 CONTACT PIN #2201

brown/gra)

redigray To Left Speaker

#6597

wesst —_| 250 +

TITLE HAMMERHEAD

DESCRIPTION #WS2054X - SPEAKER HARNESS: FILENAME, WS.VSD

DRAWN BY MMARTIN

DATE 7/9101 REVISED 8/15/01 PAGE 5 OF 10

Page 18

ACL EARTH GND ACN =

2 }GREEN #8173 - 3 COND. SVT 2 | EARTH GND WHITE WHITE] 3 | acn 3 SPIN GAP #2288] 3 [AC FEMALE #2102 3 PINPLUG #2206 SOLID PIN #21008

TITLE HAMMERHEAD.

FILENAME WS.VSD DESCRIPTION #WS2056X - MARQUEE HARNESS. DRAWN BY MMARTIN

DATE 7/9/01 REVISED 8/15/01 PAGE 6 OF 10

4 2

Page 19

12 VDC. Lockout Coil Ground Coin In 1 Coin In 2 Ground onaons orange * 2 orange, #650

black __ #650

gray/yellow black gray/brown orange 7 #651 gray/red a 187

black gray/yellow #651

6 PIN AMP HOUSING #2044 CONTACT PIN #2201 oD 127

#6537

#6537

#6537

#6537 To Coin Lamps

To Coin Lamps

To Lockout Coils

To Lockout Coils

To Coin Switch 1

To Coin Switch 2

TITLE HAMMERHEAD:

DESCRIPTION #WS2057X - COIN DOOR HARNESS FILENAME WS.VSD

DRAWN BY MMARTIN

DATE 7/9/01 REVISED 8/15/01 PAGE 7 OF 10

Page 20

4 2 1

12voc | 7LORANGE\violetblueAN.+ Senge
Ticket Sense | 2[violevblueBLACK + black]5 | GNDTo Ticket
Ticket Run | 3[violetiwhitevioledwhite]3IT RunDispenser
Ground | 4[BLACKORANGE + orange]4|. ioypcSP

4PIN AMP HOUSING #2429 4 PIN MLX CAP #2158 CONTACT PIN #2201 FEMALE PIN #2176 PINS 2 & 4: 20-14 AWG FEMALE PIN #8177

aloes1+ t2v0cRED FLASHING LED #8212
violevgreen!2|T OutWITH LED HOLDER #1017

2 PIN MOLEX HOUSING #2089 MINI KK PIN #2074

violetigreen or #651 187 To Low Ticket black -— ygaq Switch N 187

TITLE HAMMERHEAD

FILENAME WS.VSD DESCRIPTION #WS2058X - TICKET DOOR HARNESS DRAWNBY = MMARTIN.

DATE7/9/01REVISED8/15/01Pace8 OF 10

4 2 1

Page 21

2 1

P3 [RED ____ TAN/BLACK. ORANGE Lance _y, [OgaNGe __

Shan t| 2 [REDIBLAGK > &gov | « [YeLLow>
Shark 4| 3 -ORANGE/BLACK iy, 5,30voc|5 }GREEN

Shark 3} 4 LYELLOW/BLACK 43 30 voc | 6 -BLUE Shark 5 | 5 [GREENIBLACK _y, 56 30 voc | 7 Shark 6| 6 |BLUEBLACK dys 4g 30 voc | 8 6 PIN AMP HOUSING #2944 30 VDC | 9 CONTACT PIN #2201 9 PIN AMP HOUSING #8136

CONTACT PIN #2201

PS Switch 8| 1 Switch 7 | 2 Hlow/bl Pa a 7 g ey Ground | 1 }black —_____» ay Switch 5 | 5 [vetowareen ___y 95

Ground | 2 | black _______y» a4Switch 4}6ee aang42
Ground | 3 }black _______y 3Switch 3 | 7}vereNorenge:50
Ground | 4Switch 2]8Pee57
Ground | 5Switch 1 | g[Yellow/brown’56

5 PIN AMP HOUSING #2419 9 PIN AMP HOUSING #8136

CONTACT PIN #2201 CONTACT PIN #2201

PIN 4: KEY PLUG #2239

P6 12VDC | 1

221012 | sretroun7
Jewel 2]4[uhite/red54
Sewel 3|5[white/orange46
Jewel 4]6white/yellow38
f OGSonJewel 5|7.[White/green21
PAT ATATATATOTATaEJewel 6]8white/blue>13
2 000000007"12 voc | 10 }orange_dys
2OCOOOOCOCO’s12 voc | 11 }orange_ds gg
OOOC00000yavpc | 12 [orangegg

#8 QOOOO0000 # 12 PIN AMP HOUSING #8428 53 Q0OO0O00008 CONTACT PIN #2201 8000083

nme HAMMERHEAD 63 PIN CIRCULAR PLUG #8111 FEMALE PIN #8112 pescniprion #WS2059X - MAIN TO COIL BED FILENAME _WS.VSD CLAMP #8110 HARNESS DRAWNBY MMARTIN

DATE 7/9/01 REVISED 8/15/01 PAGE 9 OF 10 2 1

Page 22

TAN/BLACK TAN/BLACK #2909 2 87

63qBROWNBROWN_cq#esaT

CN 80 black black pp #851 a1 187 56 <Yellow/brownl ellow/brown — yeag

RED/BLACK, RED/BLACK #2909 see OO 7 RED RED _saq#653T es A SHARK SOL @)

A SHARK SW

B SHARK SOL @) YELLOW/BLACK YELLOW/BLACK __7)#2909 43 € M137 D SHARK SOL @ 44 @VELLOW YELLOW rq #6537 OO 880 24 «black lack gay 51 7 D SHARK SW jellow/white 42 <ellow/white #649

GREEN/BLACK GREEN/BLACK _p,)#2909 s—eew.rho eM 87 GREEN E SHARK SOL G) GREEN #653T 27 GREEN ____|_GREEN 46s black gp #651 black ppp #651 = ie7 a 87 B SHARK SW E SHARK SW

57 ¢yollowlredyellowired «sag25 ¢yellowlareenyellow/areen 5s goa

“WS 187 S167

51<QBANGEIBLACK | ORANGE/BLACK ,ay#200019¢BLUEIBLACKBLUE/BLACK72909
OOOO87OOOODD87
52 <q ORANGEORANGE-eqiosar© SHARK SOL @19«BLUEBLUEpaprssorF SHARK SOL G
<250black ppp #651.250black ppp #651
"8"CG SHARK SW"7SHARK SW
50 <vellow/orangeellow/orange ,—. 4e4917 <2ellow/blueellow/blue
61<white/brownwhite/orown[Fae 4

54 «White/red white/red | 5 | jewel 2

46 White/orangewhite/orange | 3 | Jewel 3£00001SHARK COIL
38.wiite/yellowwhite/yellow|4 | Jewel4aé6 PER GAME
<wwhite/greenwhite/greensie,O0C000O#654WHITE
21 << hite/blnitciblue]©|vewelS — To Jewel Lights1300000000 12$5 (a
33 uniteroivewhite/biue | § | \ewei 6700000000”
73% OOOOO0O00002a> 22AWG
22 «orangeorange | g | 12 voc44QQ0000000%71N4004‘2400 TURNS
39 orangeorange|g | 12 voc5 000000004&spn
9 PIN CAP #2551KESOOO0000s3¢
FEMALE PIN #21022O9 20054651 phy

187 WHITE/BLACK

63 PIN CIR.RECEP.PNL. MT. #8113 4<«—_“+_ MALE PIN #8114 7 blue Te HAMMERHEAD

FILENAME WS.VSD +#2364- DESCRIPTION #WS2060X - COIL BED HARNESS 12 VOLT DC FAN ORAWN8Y — MMARTIN

DATE7/9101REVISED8/15/01PAGE10 0F 10
4321
Page 23

Warranty

|.C.E warrants all components in the HAMMERHEAD" game to be free of defects in materials and workmanship for a period of 90 days from the date of purchase. Furthermore, all MAIN P.C. BOARDS are warranted for 180 days.

This warranty does not cover items damaged due to normal wear and tear, subjected to abuse, improperly assembled by the end user, modified, repaired, or operated in a fashion other than that described in the service manual.

If your HAMMERHEAD" game fails to conform to the above-mentioned warranty, |.C.E.'s sole responsibility shall be at its discretion to repair or replace any defective component with a new or remanufactured component of equal to or greater O.E.M. specification.

|.C.E. will assume no liability whatsoever, for costs associated with labor to replace defective parts, or travel time associated therein.

|.C.E.'s obligation will be to ship free of charge, replacement parts by U.P.S. Ground, U.S. mail, or other comparable shipping means. Any express mail or overnight shipping expense is at the cost of the purchaser.

Products will be covered under warranty only when:

The serial number of the game with the defective parts is given.

The serial number of the defective part, if applicable, is given.

Defective parts are returned to I.C.E., shipping pre—paid, in a timely fashion, if requested by I.C.E.

A copy of the sales receipt is available as proof of purchase upon request of I.C.E.

|.C.E. distributors are independent, privately owned and operated. In their judgment, they may sell parts or accessories other than those manufactured by I.C.E. We cannot be responsible for the quality, suitability, or safety of any non-I.C.E. part, or any modification, including labor, which is performed by such a distributor.