Monte Carlo TM-149 1st Printing
Monte Carlo (Atari, 1979) · Technical Manual · 84 pages · 45 sections · original scan
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
GAME SERIAL NUMBER LOCATION
The same number is also stamped on the chassis of the TV monitor, game PCB, and Regulator/Audio II PCB. Please mention this number whenever call- Your game’s serial number is stamped on a plate on the outside of the game. | ing your distributor for service.
SERIAL NUMBER LABEL ay
TV MONITOR
REGULATOR AUDIO II PCB |
GAME PCB
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
) Published by
lj ATARIINC
AT, ARI 1265 Borregas Avenue
P.O. Box 427 Sunnyvale, California 94086
Copyright © 1980 by Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Lithographedin the USA. 4d ] + W2120¢ Communications Company
Table of Contents
1 Location Setup A. New Parts B. Game!nspection 3 C. Game Installation. . 3
- Voltage Selection 3
- Interlock and Power On/Off Switches .............0.. 0c eee eee 4 D. Self-Test Procedure . . 4 —& GamePlay ..... . 9
- Attract Mode ..... cece eee eee e tenn eee 9
- Ready-to-Play Mode . 9
- Play Mode 9
2 Maintenance and Repair A. Cleaning B. Fuse Replacement... 13 C. Opening the Control Panel ... a 13
- Steering Wheel Maintenance and Repair . 13
- LED Switch Replacement.......... 13
- Gear Shifter Maintenance and Repair 13 D. TV Monitor Replacement.............. . 16 E. Printed Circuit Board Replacement . 17 F. Fluorescent Tube Replacement . . . 18 G. Foot Pedal Maintenance and Repair . 19 H. Coin Door Repairs ... as . 20 |. Game Operation. ....6 2.00.00. cece eee eee eee nee 22
3 Illustrated Parts Lists
List of Illustrations
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5
Figure 6 Figure 7 Figure 8 Figure 9 Figure 10
Figure 11 Figure 12 Figure 13 Figure 14 Figure 15
Figure 16 Figure 17 Figure 18 Figure 19A Figure 19B
Figure 19C Figure 20A Figure 20B Figure 20C Figure 20D
Figure 21 Figure 22 Figure 23 Figure 24 Figure 25
Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Overview of Game ... 1... eect ete 2 Installation Requirements . 3 Power Supply ........... 4 Interlock and Power On/Off Switches . 5 Location of Self-Test Switch, Volume Control and Option Switches . 6
Self-Test Procedure 7 Option Switch Settings . 8 Opening the Contro! Panel ........ 2.2... c cee eee eee eee 12 Steering Wheel Maintenance and Repair . 14 LED Switch Testing and Replacement ........... 0.000 cece eee 14
Gear Shifter Maintenance and Repair . .. . 15 TV Monitor Removal . - 16 PCB Replacement . 17 Fluorescent Tube Replacement . cece nett eee en eeeeene 18 Foot Pedal Maintenance and Repair eggs tO Seaway Z 19
Removing Coin Mechanism... ......0. 0.0. e cece eee teen eee 20 Switch and Trip Wire Replacement . 24 Coin Door Lamp Replacement. . 22 Monte Carlo wiring Diagram + 24 Coin Door Wiring Diagram... .. 6... 6c eee eee cece eens 25
Fluorescent Light Wiring Diagram Steering PCB Schematic Diagram . Power Supply Schematic Diagram . Regulator/Audio Il PCB Schematic Diagram ween ene ee ee 29 Game PCB Schematic Diagram... 0.2.6.6... ccc c eee eee 30
Final Assembly 44 Control Panel Assembly . 46 Game PCB Assembly......... . 47 Regulator/Audio Il PCB Assembly . 52 Steering Wheel Assembly ..........- 0.0. c cee eee ee eee eee ees 54
Gear Shifter Assembly (‘‘H” Pattern) . 56 Foot Pedal Control.............- . 58 Type B Power Supply Assembly . . 60 Fluorescent Light and Speaker .... . 62 New Coin Door (2 or 3 Mechanisms) . 64
If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.
WEST and CENTRAL U.S.A.
Parts for ail Atari Customers. Sales and Service
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103
(Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii (408) 745-2900
= From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A.
Sales and Service Only
Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347
(Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey es (201) 469-5993
= From anywhere else in this area toll-free (800) 526-3849
Location Setup
A. New Parts
The Monte Carlo™ game has five new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: Color TV Monitor. Made especially to Atari specifications, the 19-inch monitor has been color-converged at the factory. All convergence adjustments are cemented and locked in place, to prevent accidental changes. This helps provide higher reliability for the service technician. Isolation Transformer. The color TV monitor chassis in this game does not contain an isolation transformer. Atari has mounted an isolation transformer on the floor of the cabinet to protect operators. If you service this color TV on a test bench, you must isolate the line voltage! (See instructions on pages 16 and 17.)
ATTRACTION PANEL SPEAKER
—\ ed
REGULATOR’ AUDIO II PCB
GAME PCB
COIN DOOR
KN
FOOT PEDAL CONTROL POWER ON/OFF SWITCH
POWER SUPPLY ISOLATION TRANSFORMER am)
Figure 1 Overview of Game
@ Foot Pedal Assembly. This redesigned control will universally fit Monte Carlo and ali future games with foot pedal controls. It functions more smoothly and quietly because the hinge is built to tighter tolerances; the whole control is also more compact and less expensive to replace than the old style. In addition, the control’s switch actuator is stronger—it is now a flat blade, not a thin wire. @ New Coin Door. This door will accomodate two or three mechanisms, and up to four coin counters. Its triple-arm locking bar provides added security. For greater ease of access, the self-test switch is now mounted on the door, rather than inside the cabinet. Also, for simpler maintenance the door’s coin mechanisms require no adjustments. @ Regulator/Audio || PCB. This slightly redesigned printed-circuit board has two additional voltage regulators for games using 2708 EPROM memory chips. The board’s new + 12V and —5V regulators are both mounted on the heat sink. Otherwise this board is the same as past Regulator/Audio PCBs.
These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is
mentioned, you will see this symbol: a
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
[boot NOTE reine | Do not plug the game in yet!
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ = Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!
@ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets. @ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Game PCB, Regulator/Audio Il PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, contro! panel and TV monitor for secure mounting. For the safety of players, be certain that all green ground wires are secured at their terminations.
C. Game Installation
Figure 2 Installation Requirements
Power 125 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64x99 cm (25% x39 in.) Game Height 179 cm (70% in.)
- Voltage Selection
Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.
Line Voltage Range Voltage Selection Plug Color
86-104 VAG (95) Black 100-125 VAC (110) | Orange 190-220 VAC (205) Green 210-240 VAC (220) Red
ON/OFF AND INTERLOCK SWITCH
VOLTAGE \
SELECTION POWER-SUPPLY
PLUGS CHASSIS
Figure 3 Power Supply
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door or panel is opened. The power on/off switch is installed in a recessed area above the foot pedal.
Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. Plug the AC line power cord into an AC outlet. Close the access panel and coin door. @ Set the power on/off switch to the on position. Within approximately 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door.
cs @ If the results of the previous step are satisfactory, the interlock switches are operating properly. li the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary.
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.
To run the self-test, follow the instructions outlined in Figure 6.
POWER ON/OFF SWITCH
SAFETY INTERLOCK SWITCH
Figure 4 Interlock and Power On/Off Switches
Monte Cario™
VOLUME CONTROL
VOLUME INCREASE: TURN CLOCKWISE
OPTION SWITCHES (total of 12)
Figure 5 Location of Self-Test Switch, Volume Control and Option Switch
Instruction
- Set self-test switch to on position (see Figure 5).
- Activate the switches in all of the following controls:
- Gas pedal
- Ist, 2nd, 3rd gears
- Track select button
- Start button
- Steering wheel (left and right movement)
- All coin trip wires
- Slam switch
- Set the self-test switch to off position. For diagnostic procedures, see schematic drawings. Figure 6 Self-Test Procedure
Result if Test Passes Game displays the following in the lower right corner of the TV monitor screen:
RAM 1 OK RAM 20K
ROM OK
A very short skid sound is produced, and track select and start buttons light up in unison when each switch is opened and closed. Note: activating the coin trip wires during self-test will not increment the coin counters, so your accounting will still be accurate. Result if Test Fails RAM 1 Test: Screen shows “garbage” (scrolling sideways) and you hear a constantly repeated series of 8 crashes and/or skids. Crash sound(s) during any of the first four tones: bad RAM at L3 or its associated circuitry. Crash sound(s) during any of the last four tones: bad RAM at K3 or its associated circuitry. Crash sound during all eight tones: address line problems. Self-test will always stop here until you replace the proper RAM.
No skid sound is produced, and track select/ start buttons don’t light up when control or switch is activated. This indicates a bad switch, loose harness wires or connectors, or a bad steering PCB on the steering wheel control.
To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessibie when the game PCB is mounted in place.
When changing the options, verify proper results on the TV monitor display during self-test. A switch toggle in the on position Figure 7 Option Switch Settings
is indicated by a 1 for that switch on the TV monitor display. A switch in the off position is indicated by the number 0 (see example given at bottom of this figure). All switch settings are displayed on the monitor exactly as you view the corresponding switches on the game PCB, with toggles #1 on the right and toggles #4 and #8 on the left.
Toggle Settings of 8-Toggle Switch on Game PCB 7 6
| 5 | 4 | 3 | 2 | 1 |
Option
Off Off Off On
On Off On On Free play 1 coin* for 1 play 1 coin* for 2 plays 2 coins* for 1 play
On Off
On On Bonus Level (bonus = 40 fuel units): No bonus Liberal Moderate Conservative
Off On Off On Off Off On On Time (always equals 90 fuel units): 1 minute per play 1¥2 minutes per play 2 minuies per play 2¥2 minutes per play
Ott On Off On Off Off On On English language French language Spanish language German language
- Note: In the U.S. and Germany only, a “coin” is defined as 25¢ or 1 DM. If your game also has $1, 2 DM or 5 DM mechanisms, you must set the center and right coin mechanism multipliers as per your choice.
Toggle Settings of 4-Toggle Switch on Game PCB Option 2 1
| u | Off | off |
| N | off | On |
| U | On | off |
| Ss | On | On |
E D Off On Right coin mech x 1 Right coin mech x 4 Right coin mech x 5 Right coin mech x 6
Center coin mech x 1 (Both settings are for left Center coin mech x 2 mech, if a 2-mech door)
Self-test will display the following at the bottom of the screen (zeroes and ones may vary from this example). The 0 = off. and 1 = on. Toggle #8 —_,_ 0 0 1 0 0
Toggle #4 oO 0 1 U ~— 1 0 1 ™ Toggle #1
Toggle #1
E. Game Play
Atari’s Monte Carlo™ is a one-player video game that simulates driving in a grand prix race. Various video-display phrases indicate score, time elapsed (“FUEL”), speed, and which track was selected at the beginning of the game (eight different ones tanging from easy to hard). Players drive the grand prix car thru the streets, while spectators observe from the side. Bales of hay, cola stands, trees, and bushes also line the roadway.
Four computer-controlled cars provide challenge: they pass the player's car at high speed and may cause it to skid or even crash. However, the computer cars are not infallible and may aiso skid or crash occasionally. Realistic engine revving, screeching tires and crash sounds accompany game play.
The Monte Carlo™ game has four possible modes of operation: Attract, Ready-to-Play, Play, and Self- Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled and the high score today is zeroed.
- Attract Mode
The attract mode begins when power is applied to the game, after a play mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the TV monitor displays a simulated game with the computer cars zipping by and the player's car in the center of the screen. In addition, this mode shows the last player’s score, the high score today for the current track being displayed, and the score required for bonus play.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a game. It ends when the START pushbutton is pressed. When this mode begins, the messages SELECT TRACK and PUSH START flash at the bottom of the screen. At this point the player may choose from eight tracks that vary in difficulty, by repeatedly pushing the TRACK SELECT pushbutton (the numbers 1 thru 8 will appear in the lower right corner of the screen). The monitor pictures are otherwise the same as those shown in the attract mode.
- Play Mode
The play mode begins when the START pushbutton is pressed. The mode ends when the player's fuel has run out, including any earned for bonus play. After pressing the START button, the game will set the player’s car behind the checkerboard start line, 90 fuel units are granted, and the steering wheel, gear shifter and accelerator are immediately enabled. Note that regardless of the operator option setting for game time, players will always be granted 90 fuel units, to make all Monte Carlo games appear equal in game length.
As the player rounds the turns, he or she is permitted to drive somewhat off the road without crashing. However, this will cause a screeching sound and will slow down the car. Touching an obstacle on the side, such as a tree or bale of hay, will, however, Cause a crash. To continue, you must straighten out the car, shift into first gear and accelerate back onto the roadway.
Bottlenecks and hairpin curves in the road provide added challenge to the player, in addition to the computer cars that constantly pass by. Scoring is automatically calculated: each track has many invisible checkpoints that players must drive over, in order to increment their scores.
When the fuel reaches “0”, the computer checks the score and compares it with the bonus level (operator-adjustable to three levels, or can be eliminated entirely). If this score has been achieved, then extra time of 40 fuel units is instantaneously awarded. All colors are reversed: the dark road turns light and the landscape turns dark. (Game play goes on continuously while all this is happening.)
In addition, six beeps notify the player of achieving this bonus level. Only one bonus play per game is granted, i.e., another bonus cannot be earned on top of the first bonus.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect.money from the cash box. Just looking at a game will not tell you if the foot pedal, steering wheel or gear shifter controls, LED switches or coin door switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the steering wheel, foot pedal, and gear shifter—for details see this chapter.
Maintenance and Repair
GEAR SHIFTER
STEERING PCB
STEERING WHEEL
Figure 8 Opening and Removing Parts from the Control Panel
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.
B. Fuse Replacement
This game contains six fuses—all on or near the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Chapter 3 of this manual: the single fuse mounted on the floor of the cabinet and the five fuses on the power supply are all described in Figure 28. See the color TV monitor manual, TM-148, for the monitor fuse data.
C. Opening the Control Panel
Prior to repairing or replacing any item on the control panel or prior to removing the TV monitor, unplug the game. Then open the coin door.
Reach through the opening and remove both sets of carriage bolts, wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 8).
Lift up on the control panel and swing it down towards you. The three different types of controls (steering wheel, gear shifter, and LED switches) on this panel are now easily accessible for maintenance or repair. Figure 8 also provides details on how to remove the three controls.
- Steering Wheel Maintenance and
Repair
Lubrication Depending on usage, your game’s steering wheel will need lubrication approximately every 3 to 6 months. To do so, open the control panel as described previously. Refer to Figure 9 and unplug the harness connector on the small steering printedcircuit board (PCB). Then remove the hex nut on the end of the wheel, along with the large washer and toothed wheel. Pull the steering wheel out of the control panel {towards the floor).
Apply a light coat of Shell Alvania #EPRO lithiumbased lubricant (Atari part no. 78-1707) to the friction-producing surfaces of both white bearings—Figure 9 shows these areas in detail.
Then reassemble the steering wheel in the control panel, making sure the notches in the bearings, housing, and toothed hub all match up. Be certain that the hub can spin freely in the slot of the optical coupler on the PCB! Carefully plug the connector back onto the smali PCB, but do not exert too much pressure, or you will break the board. Close the control panel.
Probably the only repair this control would normally require is replacement of the steering PCB. Simply remove the two small cross-recessed screws and split lock washers that mount this board onto the black housing (the toothed hub must be off first). Replace the board, mount the hub, large washer and hex nut back on the shaft, and then plug the harness connector onto the PCB.
- LED Switch Replacement
The light-emitting-diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to R x 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ = If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in Figure 10.
- Gear Shifter Maintenance and
Normal maintenance involves lubricating two parts in the shifter every three to six months (this requires removing the control). First open the control panel as described previously in Figure 8. Then
Steering PCB Replacement
OPTICAL COUPLER
LUBRICATE HERE LUBRICATE HERE
Lubrication o— sreerine pce
coun LIGHT-EMITTING CONTACT DIODE (L.E.0.)
CONTACTS SWITCH BUSHING
y. ~~~ NORMALLY OPEN § WY (N.0.) CONTACT \ NORMALLY CLOSED NYLON (N.C.) CONTACT ‘SPACER L.E.D SWITCH: TO REMOVE TURN COUNTERCLOCKWISE
+ Remove all wires from the faulty switch. + Turn the switch counterclockwise while holding the cone-shaped nut on the out- { NO. side of the control panel. o—— procedures ——e———e SINGLE-POLE DOUBLE-THROW (SPOT) SWITCH WITH INTERNAL LED
- Reconnect the harness wires. Figure 10 LED Switch Testing and Replacement
LUBRICATE HERE
Figure 11 Monte Cario™
LUBRICATE HERE
Gear Shifter Maintenance and Repair
unplug the ‘“quick-disconnect” connectors on the shifter’s three switches.
From the inside of the control panel, remove the four flat and lock washers and four screws that mount the gear shifter onto the panel and the gearnumbers bezel. Then open up the shifter assembly by removing the six split lock washers and screws (see Figure 11).
Lubricate the spherical part of the handle and the H-pattern recess of the black detent, as shown in Figure 11. Use only Dow Corning silicone compound #5 (Atari part no. 78-16002) on these surfaces. Reassemble the gear shifter control and reinstall it in the control panel. Reconnect the harness wires as follows, making sure the right colors go to each switch: Black wires—one terminal on each switch (doesn’t matter which terminal) White/brown wire—1st gear White/black wire—2nd gear White/red wire—3rd gear
Repairs on the gear-shifter control would probably only involve replacement of switches. When removing a switch, be careful not to lose the small
Disassemble in the order indicated. (Circled numbers match the steps in Section D.)
Figure 12 TV Monitor Removal
If you should need to remove the television monitor, follow steps 1 thru 4 as listed on this page. Refer to Figure 12 above. rivet that sits above the white switch actuator. Note: the flat head of the rivet must always face towards the switch actuator.
D. TV Monitor Replacement
- Open the access panel. Be sure the game is unplugged from its wall outlet!
- If Color Monitor: Unp\ug the harness connectors as follows: one is a 2-pin connector in the harness, the other is a 6-pin connector on the monitor's printed-circuit board.
4. DANGER
The color TV monitor does not contain an hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor. isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the color monitor on a test bench, you must isolate the monitor from AC voltage with an isolation transformer.
If B&W Monitor: Unplug the 12-pin harness connector on the rear of the TV monitor chassis. Be extremely careful and never touch the red anode wire or the high-voltage tube on the rear of the monitor! Then unscrew the green ground wire that is attached to the TV monitor chassis. Also unplug the harness connector for the fluorescent light (located at the left side of the cabinet’s rear opening). Remove the wing nuts and washers underneath the wood television shelf. (This hardware is atiached to the metal “L” brackets.) Carefully slide the TV monitor chassis, still on its wood shelf, out towards the rear of the game. After replacing a monitor, be sure to run the self-test. To Change from Color to B&W Monitor: Buy the larger cardboard bezel and install it. Buy the black-and-white TV assembly and install it; plug other 12-pin connector into its chassis. Reattach ground wire. Remove isolation transformer; buy shorting plug and install it where transformer connector used to be. (B&W monitor will not work if you leave transformer connected.) To Change from B&W to Color Monitor: Buy the smaller cardboard bezel and install it. Buy the color TV assembly and install it; plug the other 2-pin and 6-pin connectors into it. Reattach ground wire. Remove the small monitor shorting plug. Buy the isolation transformer and install it; Plug its harness connectors together. The isolation transformer is mandatory with the color TV—for your own safety and for the safety of all players.
E. Printed Circuit Board Replacement
You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio Il PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:
1. 2. Open the access panel. Locate the securing screw and fiber washer that hold down the PCB in its slots, and remove them. If you are removing the game PCB, first remove the two tie wraps that fasten the edge connecior to the game PCB. Then unplug the edge con-
REGULATOR’ AUDIO It PCB
GAME PCB
Figure 13 PCB Replacement
nector from the game PCB. If you are removing these controls, refer to the schematic drawings the Regulator/Audio I! PCB, simply disconnect DP-149-01 and -02. the five small harness connectors on this board.
4. Carefully siide either PCB straight out of its F FI T
slots. Be careful not to twist the board, as this
may loosen connections or components. Re- ° uorescent ube
place or repair as required.
5. Reinstall the PCB, making sure that the connec- Replacement tor will probably damage your game and will WARNING
tors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connec-
yoid the warranty. If you drop a fluorescent tube and it
- Replace the securing screws and fiber washers ae : in the PGB. If reinstalling the game PCB, secure caer tector toes ta Heateitee lass the edge connectors with tie wraps. Close and Use care when replacing any fluorescent lock the rear access panel. tube.
- Check that the operation of the game is correct by performing the self-test. This is especially To replace the white fluorescent tube behind the
Figure 14 Fluorescent Tube Replacement
LUBRICATE HERE
i | FOOT PEDAL
ACTUATOR BLADE/BRACKET
SWITCH
MOUNTING PLATE I SPACER a.
RUBBER — ,
FENDER WASHER a @
Figure 15 Foot Pedal Maintenance and Repair
- Tilt the top of the attraction panel towards you, G. Foot Pedal Mainthen lift it up and out of the bottom retainer.
3. Remove the two Y-shaped connectors from the tenance and Repair
ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you. =? 7 The only maintenance required on this newly designed foot pedal control is lubrication. Every 3 to lec 6 months, or whenever the pedal becomes squeaky, in vigorously—you may break it, causing an im- you should apply a small amount of Dow Corning plosion! Molykote G-n paste to the wearing surfaces of the
- Close up the game by following Section F in steel pin. Also apply this lubricant to the flat surreverse order. faces around the pin holes on the pedal.
- Replace with a new tube. Do not snap the tube
See Figure 15 for details on how to remove the pedal from the wood enclosure and exactly where to lubricate it.
The most likely repair would be replacing the switch; perhaps the spring or the blue temperedsteel actuator may also break from abuse. Again, refer to Figure 15 for details on how to replace these (. items.
H. Coin Door Repairs
The new Atari coin door has been totally redesigned, as described on page 3 of this manual. For ease of maintenance, the coin door mechanisms require no adjustments. For plastic mechs, use only hot soapy water to clean them: boiling water is not needed nor even recommended, as this would soften the plastic.
To remove any mechanisms, or to replace the small lamps, switches or trip wires, follow the illustrations and instructions given in Figures 16 through
- To obtain part numbers for ordering purposes, refer to the detailed exploded drawing of the coin door and parts list in Figure 30.
COIN MECHANISM
STUDS
@ Open coin door. To clean or replace a mechanism, locate the black spring clip above the coin switch, Pull this clip towards you, then swivel it up 90°. @ Push the mechanism towards the right, then pull it out. @ When reinserting the mechanism, be certain that no wires get caught up in it. Align the mechanism between the top and bottom pairs of vertical tabs in the inner door panel. @ Push the part of the mechanism closest to you to the left, so both of its round studs slip into the curved notches on the inlet and return chutes. © Tur the black spring clip down again to secure the mechanism in place.
SPRING CLIP
Figure 16 Removing Coin Mechanism
@ Remove the plastic switch cover by squeezing together its two prongs (just underneath the switch). Tilt the bottom edge of the cover out to the right while pulling down on it. Unplug the quick-disconnect wires on the switch and lockout coil. Use a longer-style 4” socket wrench, so you won't damage the trip wire, and remove both nuts that ‘secure the coin return chute onto the inner panel. @ Now hold the return chute subassembly together in one hand, and replace the defective switch. @ The trip wire can be replaced by carefully prying up the black internal-tooth retainer with a small fiat screwdriver. Then remove the wire from the brasscolored stud. @ Be sure to replace the wire with another of the proper color (four are available, depending on coin denomination). li the new wire is loose when placed on the stud, squeeze the stud’s two halves together with a pair of pliers to secure the wire. Then replace the retainer. @ Make certain that the wire projects thru the entire width of the coin slot: otherwise no credits will be granted, even for genuine coins. The wire’s normal rest position is against the top of the curved slot. SWITCH COVER
QUICK-DISCONNEC’ WIRES T
TRIP WIRE
SWITCH QUICK-DISCONNECT RETAINER WIRES
Figure 17 Switch and Trip Wire Replacement
COIN INLET CHUTE
LAMP BRACKET
@ Remove the screw that secures the lamp and its “2” bracket fo the coin inlet chute. ®@ Replace the burned-out bulb. Then mount the lamp holder bracket back on the coin inlet chute.
Figure 18 Coin Door Lamp Replacement
I. Game Operation
Monte Carlo™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the contro! panel, foot pedal and coin door. These inputs are processed by the game PCB and output to the TV monitor, loudspeaker, Regulator/Audio II PCB, and control panel.
The Regulator/Audio {| PCB performs two functions: first, it regulates the + 10 VDC from the power supply to +5 VDC, the 6.3 VAC is regulated to —5 VDC, and 25 VAC is regulated to + 12 VDC, Second, it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio || PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.
The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4, and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply Chassis.
Figures 19A thru 19C are the wiring diagrams that show the electrical connections of the Monte Carlo game. Figures 20A thru 20D are the schematic diagrams of the Monte Carlo game.

This page is a drawing, shown as the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
INTERLOCKS, ne [Hoe fiw 7 ser
Ie
| a | _ | ba | COLOR |
3 MONITOR
| FoR ELUORESCENT LiGHT | Ps | ONLY |
Wrgiee DING IEAM See e2ese3-) 7
| ; | TRAD NeTA | aA |
| us | 6 | (SOLATION TRANS |
SPEAKER lo
1 S207 |
| 2 | =, | a | |
| 3 | Soren | |? | BLACK & |
| 4 | AONY | a | WHITE |
| 5 | one | S | MONITOR |
—+tel —— ONLY
| ene] $ | ance Peer | ° |
| a | ISOLATION TRANSE | ra |
only | ae
| wir! | 8 | eh | w | J |
re i {2|
| — | Guy | ~ |
aa " — aq
| ——=. | — | a | \ ot | oF |
| 4 | — | WEN] oo oo on oi | SLACK B WHITE | |
| cn | ee | | tip | Se oe 0) giz pag | MONITOR ONLY |
\SVAc 22
| Saka | a) | cook | ah |
an MONITOR |
| Trep | eae | Bh |
2\5 1 3/4 oy, 22 Mm sie eh)
| eK | | | i | f | = | — | F=S57 | | TRACK | 1 |
j
| w/eK | | v | wisk |S) | wv a aR | Select | | | |
| wien | | | \ | aK | 1 | gnc! | I |
| wir | | i | \ | or NOX | cla | H | |
| wioR} 2 | 1 | woStL ts suwerer | wiler | WSR | ls | |
| wir | lo | Lee | | | |||
| wi | | | sre | pend | =>: | ||
| wien |° | sr | [oo] | 383 | al | START | i |
| ’ | ! | WIGN 5 | mR | |||
| wie | |) | Lo | wisn | | ra\t | to ie | 1 |
| + tty | I | NG | ||||
| 7 | res | ° | vat | ah 4 | wistINSRs. lex | | |
| a? | l | Lees | Lsxfo seal! |
" we
| w|i.) | [osu | fon | | | ot | | |
eo of \
| P24 S24 | wily. 40 °? | i |
- ‘oo! STEERING | P50. i
| NOT | ae | = | — | = | = | —-- |
AX THE TRIAD _NuTHA
aA TRANSFORMEI: 1S AN ALTERNATE FOR THE STANCOR Paeee.
FOR GAMES sQUIPPEO WITH ADOSOSS=xx COIN Sook SEE COIN SODR WARING DIAGRAM CBO4SOI~S1 AND con SOSR ADAPTER HAGNESS ASSY/ WIRING DiAGRAM AOSSS19-O1. NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issved, and neither receipt nor possession thereof conters or transfers any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any Tight to reproduce this drawing or any part thereof. Except for manufacture by verdors of Atari, Inc,, and for manvtacture under the corporation's writ ten license, no right to reproduce this drawing is granted or ‘the subject matter thereof unless by written agreement with or written permission from the corporation.
LEFT com sw (wed CENTER CON Sw (WO) RiouT COM Sw (NO, Teor swircn SLAM Switem Sw eNO toy 9c] LEFT Com LocKour cor! CENTER COIN Woe KeUT coc] = con LockaUT epi (NOT USED) NOTICE TO ALL PERSONS RECEIVING THIS (NOT USED) DRAWING: CONFIDENTIAL: Reproduction forbidden without RIGHT com METER the specific written permission of Atarl, Inc., nov oc| Sunnyvale, CA. This drawing is only conditionally issued, and neither receiptnor possession thereot_ CENTER Cos METER conters or transfers any right in, or license to use, rove the subject matter of the drawing or any design of eer com METER technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ ten license, no right to reproduce this drawing is granted or the subject matter thereof unless by Written agreement with or written permission from tovoc, eavac! G3BVAC COMMON
cnasss ono [| wey on aieK
iby), Siu F ervers wilaR. eR perrere wi JBN fen on Pervary mibK Ty
{
a gar sae _ es “wig | | + * 1
- -
Stam ~
a.
A Ces) «iQ, ws wien Dios wou Qjwe TS L ra kignt came cenreR une ser mee
vet fo stad een
| 2 | > | >| | |||
| 2 | 3 | ar | 3| | m7 | (BRI BU |
i¥ wiSK7ENT— RIGHT COM METER
| ag opie | cease poe | | | ote fe |
| Secor, | Ss. | coe Lae |
A 2
| g | a | yl |
| 3 | 3 | > |
| wo. | wo. | we. |
5 P
| 8) | be | abe | ah. | ||
| 3LI | our coms | 3D | enven com | BLT | eer com |
| BEneS | ce | pape | lex |
Sa LEFT com weTer
RiGnt CoN MECH CENTER CON MECH CesT CON Geen
Figure 19B Coin Door Wiring Diagram
oo 1 en cn [DALLAST N EVAG ae
Wx ~*~ SPLICE (5 PLCS)
Figure 19C Fluorescent Light Wiring Diagram
GROUND
Figure 20A Steering PCB Schematic Diagram
TRANSFORMER
B ne i 7 | a [2] wax
| voutace | of | | [3]w | | | cH | ; |
SELECTION [ R : Mbt
| seem | [a[SN/v | BN | UBY | 9/65 yae lay | ||
| SHOWN | | | s | ANY! 95v | ‘lg | os | POWER, |
k TO i 3 i = PCB | 3 sv | BY OuT
sv ouT
AC INPUT
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the ‘specilic. written permission of Atar, Inc. Sunnyvale, CA” This drawing i only conditionally issued, and neither receipt nor possession thereof Confers or transfers any right in or icense to use, the subject matter of the drawing or any design oF technical information shown thereon, nor any
Tight to reproduce this drawing or any part thereat
Except for manufacture by vendors of Atari, Inc., nd for manufacture under the corporation's wit. ten leense, no right to reproduce {ns drawing Is Granted’ or the Subject malter thereol unless by Gritien agreement with or witten permission frort the corporation
Figure 20B Power Supply Schematic Diagram
10.3 voe UNAEG
Qs N3055 cas ry ANae NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any fight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ ten license, no right to reproduce this drawing Is granted or the subject matter theraot unless by written agreement with or written permission from the corporation.
fb sv ate JT
peg fe i
+10 asvoc
Bee low
i
\ 1 | 2002Av B22 CM 100.01 | | B13 7 maaan |
pA i 220 ct | R28 Sau t i Ve / a R20 a19 i
sn a -
Figure 20C Regulator/Audio Il PCB Schematic Diagram
Diagnostics
The Monte Carlo™ diagnostics are a subsection of the self-test procedure. Start the series of 13 diagnostics by first entering the self-test. Then simultaneously hoid slam switch on coin door closed while pressing START button. Letter A will appear on the screen below last digit of option switch display—meaning Test A is in progress. This letter increments with each press of START button. To advance to next test, press START button. To freeze the screen image during any test, put the gear shifter into 1st gear (exception: image will not be frozen in Tests G and M). To unfreeze the image, shift into any other gear or “neutral.”
Test A, Horizontal Playtield Scrolling Playfield characters and colors are displayed scrolling smoothly. Test B, Vertical Playfield Scrolling Test C, Player Car Rotation Car in center of screen rotates clockwise (playfield will be blanked out). Test D, Drone Car Vertical Scrolling The drone or computer-controlled car will scroll across the screen. Test E, Drone Car Horizontal Scrolling Test F, Drone Car Rotation and Colors The drone car rotates clockwise and jumps to all 4 corners of the screen while rotating. After each complete revolution, its color will change (4 colors in all). Test G, Video Invert and Beeper Sound The solid background will alternate between normal and a lighter value of grey or a lighter color. The beeper sound will go on and off. Test H, Player Car Motor Frequency This sound will start at a high frequency or pitch and gradually go to a low frequency, then repeat. (You will also hear the player car sound in Tests I, J, K, and L.) Test I, Drone Car Motor Frequency Test J, Drone Car Motor Loudness This sound will start at a high volume and gradually go to silence, then repeat. Do not adjust the volume control during this test. Test K, Skid Sound Test L, Crash Sound Test M, Convergence Pattern The convergence pattern is used to adjust color convergence on games with color monitors. For instructions on how to converge your monitor, refer to the service manual for this color TV, TM-148. Do not attempt to perform any color TV adjustments unless you are a qualified technician!
Push the START switch one more time to return game to self-test. Then set self-test switch to “off” to return to the attract mode.
e Te
Fray Fe +i2v +sense [2i + 3 Ro, 8 ie9 32 v]pasv cio Chins 35,38,82 ik (PuLLuP) loo T (BYPASS) ? +u sv 7 7 8 re POWER INPUT «Ll... 2,038, 36, 3] a 148-50) -sv “sv (BYPASS) > i in 1 +5VRET es 212 14.34.37 Ale Mice L “Tre if (ByPaS5) (ROWS 2,4, 1,10)
sense [22]
Figure 20D Game PCB Schematic Diagram
Pee
| ef | * | ob |
2)> 4, 8 o ia teu <_tH
| wf | 3% [5 | Tee |
ews + : cre ai : ri Rete oy z Is
Peis Pe
. SYNC
Oo ts0¢ PRI bre ° ls
| + | Pos 2 | SYNCH |
ce $7* gf : a z 3 BRD
Re 250" —tSo!2 TSeH (soe PRO ap 19 bs
| ef? | |; | aap | de | t | |||||
| oan | mo | TONE | >, | | | ~ | be | Boe | PEs | eee |
2 a
| uf | e874 cle | af | este [a | cP | aaa | |
| ica | ae | ad | CS ee | eT | Usreaa cofS—sler | sigan cof'> |
| ry | 1 | cx COUNTER | 2heq COUNTER | |||
| if | ‘aaaa ac apc | GA 08 acaD Cc | ||||
| FRO | BL Atte, | sep | Buu |
PRO PRO
Bo SYNe. Boe] Lfo2 fc al 2223 338
| tia | ge | FRSS | 3838 |
5 cS Es
syne — So av —[So-2 ized C08
'S/qy
| rey | —Hae | X® | Of |
2), 200 34 upc ——
| ev | AS SNE Ito | av | rad |
We — 2194 cozsiay] 2.
| 4 | i" | ee | |
| ee | Cee | YeLANK | a—[Sot_wv |
| 4y——az | VECANK | {S06 |
é wv
| Sia | ob | re |
| = | Ae | NOTICE TO ALL PERSONS RECEIVING THIS |
cet DRAWING a] vsene, CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sing, Sunnyvale, GA. This drawing is only conditionally issued, and neither receipt nor possession thereot conlers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any fight to reproduce this drawing or any part thereot Excepi for manufacture by vendors of Atari, Inc. and for manufacture under the corporation's writ ten license, no Fight to reproduce this drawing is, granted of the subject matter thereo! unless by written agreement with or written permission trom the corporation
MICROPROCESSOR
as
ala
maur Aa
az cz 90-609! AN (Aca)
Fa i user 20} P8219 sas
| b2 | 1s | stg |
7 abe
| amped | <2} py fu | aw | |
| Reser | co | ~ | |
| sro f2 | elf | 2 | earo |
Nar
“
es saio—— S02 — axe > sit pee FO 4) 5%
| alte | a | vsudls | as |
! ©
| 2 | , | wl | © | | | as |
1B Ba
| ulsarssr |, | asi | at _fy | 7 | as |
2 x Shs para ©
| eur | wf | af | 2 | ||
| 24 | Jaa OR | Nie | ‘s | zk | BAS |
| 2unz | Isp | asf | 2 | gas |
s
| 1S | |; -® 4 | Me | ||
| a2 | - | Baa | ||
| as | aft | “| -3—— | }*$— | eat |
| ai — | ae pO | « p | 2 | aad |
a Tp,
| Ba | A | — +5 |
10K HOLANK +
| dw | van | : | . |
2 48 lop tT. ipo
| ae | lew | OH? | co, | PO | any |
| ao) | Be | wd | |||
| 27 | GDi2] 6 | 4 2S | ape |
NOTICE TO ALL PERSONS RECEIVING THIS fac) DS da ob
| FIDENT | DRAWING | f | Tse | 28 | oo | | | Pe | aps |
CONI VAL: Reproduction forbidden without T
| the specific written permission of Atari, Ine. | . ~® | Fee coda, | 745 | Lee) | ang |
‘Sunnyvale, GA This drawing is only conditionally a
| issued, and neither receipt nor possession thereot | D> | djs{_ | AMPBO“D | & gy | ||
| confers or transfers any right in, or license to use, | 3 | i | aps. | ||
| the subject matter of the drawing or any design or | Da | Reva | |||
| technical Information shown thereon, nor any | 30 | Cw. | ata) | ||
| Tight to reproduce this drawing or any part thereot. | ls | A | eo | ||
| Except tor manufacture by vendors of Atari, Inc., | (30) | DE | |||
| and for manufacture under the corporation's writ: | 32. | 2 | wo], | a | spr |
{en license, no right to reproduce this drawing is oe
| fanted or | the subject matter thereof unless b) | c® | oY | |
| frritten agreement with or written permission from | ps fo | fl, | A | Be |
the corporation. Dine Ta OGOSOC ra aim 00 [09 [oor BAI3 -
Figure 20D Game PCB Schematic (Continued)
MEMORY MAP
ADDRESS: rw aaa FUNCTION HEXADECIMAL[ATS AA AID AIZ AT? A10 AQ AB AT AG AS Ad Ad A? Ai_AO| [D7 DS DS Da D3 D2 Di DO
| 2000-00F F | 0 0 0 | A AA KR A AD | D D BD D D D D 1 | PAGE ZERO RAM | ||
| ‘0FE.003F | 0 0 0 | oO | AAA AAA | DD DD D DO 0 D | ALPHANUMERICS | |
| (0800-08F F | eo 4 | AARARARA | D 2 DD D DB D D | PLAYFIELO RAM | ||
| 1000 | o 1 0 0 | oo G | w}/b D D BD D D D 0 | PLAYFIELD VERT FOS | ||
| 1020 | o 1 0 0 | oof | w/D DBD 0 D D D D 6G | PLAYFIELD HORIZ POS | ||
| 1040 | o 10 0 | o 1 0 | w | DRONE CRASH RESET | |
| 1060 | 0 10 0 | oo. 4 | w | CAR CRASH RESET | |
| 1080 | 0 1 0 0 | 1 0 0 | w | DRONE COLOR 2, CAR ROTATION | |
| 1080 | 0 100 | 10 4 | w | STEER RESET | |
| 16C0 | 0 1 00 | 1406 | w | WATCHDOG RESET | |
| 10E0 | 0 100 | yo 4 | w | SKID RESET | |
| 1400 | o 1014 | 0 0 0 | w]D D D Db D D DD | MOTOR SOUNDS | ||
| 1420 | o 104 | 60 4 | wjo DDO | CRASH SOUNDS, | |
| 1440 | o 401 | 0 10 | w | SKID SOUND ON | |
| 4460 | 0 104 | oo 14 | w|bD D 0 D DB D D__D | DRONE HORIZ POS | ||
| 1480 | o 104 | 1+ 0 0 | w]o p 0 D OD D © OD | DRONE VERT Pos | ||
| 1400 | o 104 | 10 4 | wo | DD DB DD | DRONE COLOA 1, ROTATION | |
| 1460 | o1o041 | 4100 | w]D DD | COIN COUNTERS (L.C.R.—1 = ON) | |
| 14co | o 404 | + 100 | w | D | ATTRACT (= ATTRACT) |
| s4co | o 104 | 1400 | w | D | TRACK SEL LAMP (0= ON) |
| 14¢0 | o 104 | + 100 | w | D | START LAMP (= ON) | |
| 14E0 | o 1041 | yor ot | wd | D | VIDEO INVERT (1 =ON) BEEPER (0=ON) |
| 14E0 | o 104 | w | D © D0 | DRONE MOTOR LOUONESS | ||
| 1800 | o 11 0 | o o O]R/D | START SW (1 = ON) | ||
| 1800 | 01 100 | a | > | ‘st GEAR (1 = ON) | |
| 1800 | o 4100 | o 0 off | D | CAR CRASH IN (1= CRASH) | |
| +1800 | o 110 | 0 0 ofR | D | ORONE CRASH IN (= CRASH) | ||
| 1801 | o 410 | oo 1fRrlo | SLAM SW ( | ||
| 1801 | o 140 | oo 1]R | D | 2nd GEAR ( | |
| 1802 | oy 10 | 0 1 olr|o | TEST SW(1 = | ||
| 1802 | or 1 0 | o 1 oR | D | ged GEAR (1 = ON) | |
| 1803 | ot 1 0 | oO 1 t/R]D | COIN SW (LEFT) ( | ||
| 1803 | o 110 | o + atR | . | TRACK SEL SW ( | |
| 1804 | o 1 4 0 | 1 0 o|plo | COIN SW (CENTER) (1 = OM | ||
| 1804 | o 1 1 0 | 1 0 9]R | o | GAS SW (1=ON) | |
| 1805 | o 110 | 1 0 1/8 |o | COIN SW (RIGHT) (1 = ON) | ||
| 1805 | 0119 | 10 44R | > | VBLANK (1'= TRUE) | |
| 1806 | o 110 | 1 1 ofafo | STEER FLAG (0= TRUE) | ||
| 1806 | o 110 | + 1 0[R | D | STEER DIR | |
| 1807 | o 110 | +1 a/R ]o | ‘CAR SKID (1= ON) | ||
| 1807 | o 110 | +1 a]R | D | DRONE SKIO (1 = ON) | |
| 1600 | ota | o oR | Cr) | OPTION | |
| ico | oor 4 | o ofR | DD | OPTION | ||
| 1601 | o1 14 | o 1fR | d © | option | ||
| 1c02 | 044 7 | 1 OR | DD | OPTION | ||
| 1003 | o1 44 | voa]e | DD J OPTION | ||
| 2000-3F FF | 1 A AA A A A AAA A A A A[A]D _D DDD _D_D_D | |8KPROGRAMROMIPROM |
{Sx oe 2 fico gas
Ale
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., By ‘Sunnyvale, GA. This drawing is only conditionally mike issued, and neither receipt nor possession thereof
| sais —3 | aa | conters or transfers any right | in, or license to use, |
| “ | 2 | Perv | the subject matter of the drawing or any design or |
| an —4I5 | 2p Beran | technical information shown thereon, nor an |
bh? zom3L right to reproduce this drawing or any part thereo!
| Baio —Fla | bie | . | Except for manutacture by vendors of Atari, Inc., |
sh’ — aomzm and for manufacture under the corporation's writ:
| abS— | zoe | ten license, no right to reproduce this drawing is |
Pa granted or the subject matter thereot unless by ap4— aon written agreement with or written permission from os the corporation.
| or | vz | ib2— komo |
L342 ght aor
| : | [econ _*} | ADDRESS DECODER | |||
| a | a | AND MEMORY | |||
| ware | — | =e | |||
| me | sb | pave | 1 | ||
| i | J | “ | |||
| gay | —Bic | SP. | say | —3| | |
| aro —4la | 1b*— | SKIDRESE | sae | 4 | Sure |
| sas —5]y, | “py | bas | __ | om |
sp&_ sTeeRRESeT DRROT abit carror CAVPOS 3p4f— canensurer BRAPOS 2b34— pacasnmer SKIDSND
| 7 | p21 puptoms | CRASHEND | |
| saz | gb! | pypLoap | MOTOREND | |
| Door | 9 | v | MOTORSND |
Te >+_ WATCHDOGRESET
| osu | + | “4 | + |
=5v
| say | + | t | t |
Bato
| ae | bE) | Prep ut | ||||||||||
| ola: | fee | ie [see | lis far | mre | fetes | pe | fie|ar | fae | fav | fe | oar | dae |
| ie coe | Ap tsy | [Ro <s3 | Recs3 | [wee vas | so vee | BD NBS | [SD VE | |||||
| luSo,<Cibay — fevdo) cider | fos Gear | favbo) Cede | ||||||||||
| Cn | ae | ces | urel | ue | Mt | n/p | ||||||
| ossretcamee forspes(ancelloxsres (erietl]ossiow saat) | wa | @ | a yratizen) | |oscira¢2n |
ga[earerdevom [osstea area) sera) aoa) [ose tisciroe) | O2877'2708)| 225778 (2198)] 022 772@708) |o2s778(2708) ea a9
| paa— | = | + - | Ae |
ss a Bae. Ae ens as Sea aa a3 3 Baz az Bal fat
| BAO. | 4 | iad | te |
27 a
| De | fs | be |
| 25 | 5 | og |
Bal coy’
| o: | = | 3 | a | ||||
| De | i | oz | |||||
| DI | 2 | Db | |||||
| tse, | ae | ot | ar | r | ™* | ||
| (rates | (Pawiest | Gores |_ eines | rom es | rom os | fos cs | Pom cs | |
| prcisp2o | Tey wy ze | ry 35 | iy 20 | ry To | eGHNLO | GIO | pa aT |
| row J | xowaT | xowe J | noma | | xomm el | ram | wom] | aa | |||
| roa | Rome | ROM | Rome | ||||
| re | Te | +> |
STEERFLAG.
STEERG
SWITCH AND
STEERING INPUTS
tov
Bsr Peae ir . os oes = steera [s}— Pos dD. of steeapin 1aoub tT (S14 2 x8. ese iS94 als PP Tei a. > > rr
ese
ote
orexrara STEERFLAGcor fo + a 807
come [a ty
come [9 vest |e
Stam [a starr [le
470x PL Tecoma > Te, conc >——1 Te, come S>—__} tev Te,sTaaT >I
Ll Satiye = 3] 313 ax UAele
aeSeS TEEROIR VSTARR as [F TRACZSEL [o aro [i ano [a Tat [x]
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, andneither receipt nor possession thereof confers or transters any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any Tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc. and for manufacture under the corporation's writ: ten license, no right \o reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission trom the corporation.
+5y
sw, cS) ars lone
| dips | 4) | & | |e |
aps
| Pal | Ts | 2} | - | bo | aoe |
at 7
| gle | 4 | 2} | 48387 | bp | gos |
| al | nN | J | io | aoa |
ee) 4 Yooh T ort
ekanes a a
4 |e a hice
- Eber 09 {2 eps ala 8
| st | be | 4 | ees |
ir ‘
| “| | ve | 4 | ee Seu | |
| 7 | it | + | Mh | |
| = | 7 | 7 | = | Lace |
| i | Mo | —+ | 3) 203 |
: ort”
CREE s rr >
| cARe | appt | 4s | al, 7 gfe | |
| cary | é | B | a> | |
| 2 | Elpeaecs | Sale | cae | |
| wee | 8 | a] Sesi74| | ||
| STS | emne | ce | a | caRcesuIN, |
e a
aR9 pRekewesr | q
| DRONE2 — | 12, | “ | 9 | 3 * | ale |
| Ls3e | 0} | t | ul | © isi |
PeeTTSo — gwwe—2{en- DRERSHIN, s UIs
‘5 }jopay>
Ciao.
| 2 Joien Jo
so. toh
PFLOZ gs
| Pritbt | 43)2 | 4} | 2laer | ||
| ceash | #1] | Tio | cua: | ee | ape |
| = | cope | & |
PRIS NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specilic written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof Confers or transfers any right in. of license to use, the subject matter of the drawing or any design of technical information shown ‘hereon, or any {ight to reproduce this drawing or any part thereo! Exceot for manufacture by vendors of Alati, Ine., and for manufacture under the corporation's written license, no right to reproduce this drawing 1s, granted or ‘the subject matter thereof unless by written agreement with or written permission from the corporation
‘ Ka: cancrsmin +] 2 apy pReAsHin —@ b> “ape S307 aie a2
OPTION AND CRASH DETECTOR INPUTS
Figure 20D Game PCB Schematic (Continued)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Monte Cario™
| en | 2s | pete |
2 mOLANK * 4
PEWNDO
+8 <r rm
me
g 3 PLAYFIELD AND AiMe—Sfas Ss 2 ALPHANUMERIC:
| AS | Ae ae | oa | fis far | fae |
| An? tas ES | Rete | [we vee | | | |
| wis | -3]ea BS | vos (va | ||
| —al* | be | Ee | oe |
av—4fas we ayaa 2
| “| | pa | a |
Waal a 44 —S]ao 3
| et cea | 2 | i | ||
| ot | Poa | as S | consrS | |
| eves | —4 | as | maa | 2 |
| evee | as 5 | fae | 3 | |
| evr | a | i | 3 | |
| Pvpe. | ny | oh | bs lob | = |
| Pues | Ao | ear ert | ||
| a5.> | fo | «|, | oe | | |
| 3 | De | />—$2}a | ||
| 3 | os| | c | we | es |
| go | Co | ae | 77] soe | |
| 5 | pa | ITH? | sures | |
| oy | | | 7 | ¢ | |
| 8 | DI | 3/5 |
2 2
| ca: | 4 | i |
| fram es | dom es | | |
fang rs
| eRDPS | + | ai |
40, as pos —42f>o% cor
| we | Ku | pce, | 4 |
va] 22°71 | g07009
| 1] | 5 | won |
an oon wan ware ase are
| 1 | as | 5 | ee | |
| a | an | ps 87 | pelt — reer | |
| 1 | a | 7 | Ld | weer |
| al | counter” | | | ||
| Ao | pa | at} ceasncone | ||
| te | wt | ae |
A Joo is
| is | eo | yoshi | — eo | , |
10 > ory Ce
| B | 22 | pas |
voi oe aro)
| - | aa | por tS] | » 1202) | ooo | ||
| vos | ope, | poo | fed}, | 2 [28 | pee | |
| NOTICE TO ALL PERSONS RECEIVING THIS | Hos | poz | pos | 22], | 5 pel) | aos |
| DRAWING | yee | =P! | yo }* uszes? | hoe | ||
| CONFIDENTIAL: Reproduction forbidden without | varie | ae | poe, | OO | a | aoa. |
| the specific written permission of Atari, Inc., | . | pos LSI, (Sta) a | ap | |||
| Sunnyvale, GA" This drawing is oaly conditionally | L___ | ber | Oat | NS | fie Gay 2? | |
| Issued, and neither receipt nor possession thercot | ia|* | xeva | eas | |||
| conters or transfers any right in, or license to use, | PDI | 15 | a fe | @D) | ||
| the subject matter of tne drawing or any design or | OT | 3 | p=) 0 |
technical information shown thereon, nor any zal Tight to reproduce this drawing or any part thereot +12 Except for manufacture by vendors of Ataf, Inc. eee and for manufacture under the corporation's writ: {en license, ro right to reproduce this drawing is granted or the Subject "matter thereot unless by written agreement with of written permission from the corpe‘ation RAW
AUDIO TERSHEND,
Boe
Ros
Boa
+sy Us
CRASH
oa, [> ASKS, cease
CRASAL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction (orbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA, This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, {the subject matter of the drawing or any design of echnical information shown thereon, nor any fight to reproduce this drawing or any part thereo! Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is Granted or the subject matter thereof unless by written agreement with or written permission from the corporation, +BY xrvencr
4 Pa ® %
| Vos | oS | —'de | ayes | [So | +sy |
zhesse| ae] c2 airy ee] ida counres aed (GA 08 3 9d ew hel Ts |e 1 B ies MoTA
om —
ites ““aol®
| Bor | ae | al | WOES INVERT |
| god | icp | sof2— | Beeper |
al? re Sls
| BOS | shPsne[,__ | bOUPS | |
| Boz | lo | Lovee | |
| BDI | cpp | 3 So | eet |
| aod | pa | Loug |
a RR
sroror 8 motor?
—Marore morers --moToR+ 2—moroes
| Bo | af | — moroee, | |
| ee | p> | a | morori |
a ale Fs Rd a
Figure 20D
Game PCB Schematic (Continued)
(be
hea 10 ; a9 oP AUD
| Is | Hee | 52 |
ls
Ie BO, oe rarer’ e, [Poy sf) oy TSo2 < [et 2 — seretcr 5 Fad the Saar >
2 a> ls vee
| Ls | sao | gaz | 679 | |
| ia | ED | nears | Bane | |
| le | consis | wee) | ||
| 9 | Bee | eas | ||
| sas ote | ¢ | ae | ete | |
| RES | galt | rae | ee | ees |
| an | ceasng | ea | eas |
° case —_ | cess, —— S18 — “YY TERS 198 fae Je se, S88 moray ——p ye 22 we FIP woronaupe tev ao cups wou
- 2 fot — arrancr 280 to ‘si bows “ ce
ess Love soraRs AAA a eae ale mores, : a sapToRe Ww cunt eat mover Ag? car, 7 ass 22M sl coy tH motor aur Aone Noon, pats 1st ea
BAN
MoroR Auoz —
MOTOR AUD TST, a 22, 25% yy 4 eos Loves
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any tight in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor an) Tight to reproduce this drawing or any part thereo! Except for manufacture by verdors of Atari, inc., and for manufacture under the corporation’s writ: ten license, no right to reproduce this drawing is granted or the subject matter thereot unless. by Written. agreement with or written permission from the corporation.
supa,
{TJ aver 2 ovr
asv
alsl3 Pewado— Yas al al 8
prcowr2 —!}a °, oxcougs —Yan nt ie 3PL >—<r RED compu S eReen CART Bas el S 61 79, BLU CARI Baa ye af paonez—4Jas y= °*P 5 prone; az Re OFT T] RED 6 eo tel GREEN ~t 2 5 1 +o] sve Fes
aisiyoco eas hae LAA TP, BI ID Vie oboe HBLANK Prue YECENR ee
MSYNC,
SING
VIDEO AND COIN COUNTER OUTPUTS
BOT we L
pa] aw vio
@] viorer I
[as anode],
Boe Bos
Bb —
Bre.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally. issued, and neither receipt nor possession thereof confers or transfers any right In, or license to use, {he subjgc! matter of the drawing or any design of echnical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manutacture under the corporation's writ: {en license, no right to reproduce this drawing is, Granted or the subject matter thereo! unless by written agreement with or written permission from the corporation. TRACK SEL LAMP,
START LAMP
Figure 20D Game PCB Schematic (Continued) CON CENTRE
COIN CNTRE
COIN CNTRR
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your game. Please note that, for simplicity, common hardware has been deleted from some of these parts lists. This includes screws, nuts, bolts, washers, etc.
The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00thru 99-, then 000598- thru approximately 110000-.
When ordering parts from your distibutor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Illustrated Parts Lists
19" Color Monitor or A035662.01 for 23” B&W Monitor Fluor. Lt. & Speaker— See Figure 29 | yp 002728-01 a 005419-01 ‘ 007882-02
000268-02
‘A035663-01 19” Color Monitor Assy. or A035664-01 23" B&W Monitor Assy.
035438-01
Control Panel Assy.— Reg/Audio ll PCB Assy.— See Figure 22 See Figure 24
‘A030169-02 Game PCB Assy.— See Figure 23 006870-01
034536-02 ‘A021700-01 ec
03579801 \ for B&W Monitor Only New Coin Door— See Figure 30 009992-01
Foot Pedal Control— ‘See Figure 27
A034631-01
NOTICE TO ALL LORE RECEIVING THIS A035791-01 oF -02 CONFIDENTIAL: Reproduction forbidden without for Color Monitor only the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally (A033016-01 or \ issued, and eliner receipt nor possession thereat Type B Power Supply— Confers or transfers any right inca; Neeneto use, ¥Pe eee Figure 2 ‘03395801 {ho subject matter of the Grawing or any design of ig technical information shown thereon, nor any ight to reproduce this drawing ot any part thereot Except for manufacture by vendor's of Atari, Inc, A035659-01 and for manufacture under the corporation's writ: {en license, no right to reproduce this drawing is, Granted or the subject matter thereol unless by written agreement with or written permiston from Figure 21 Final Assembly A035656-xx B and A035667-xx B
Figure 21 Final Assembly Parts List
Part No. Description
Control Panel Assembly—see Figure 22 Game PCB Assembly—see Figure 23 Regulator/Audio Il PCB Assembly—see Figure 24 Foot Pedal Control—see Figure 27 Type B Power Supply Assembly—see Figure 28 Fluorescent Light and Speaker—see Figure 29 New Coin Door—see Figure 30
A021700-01 Coin Box Assembly (3 holes) A030169-02 Volume Control/Bracket Assembly
| A030268-01 | Coin Box Assembly | (2 holes) |
| A033016-01 | Strain Relief Power Cord | (domestic) |
OR
| A033958-01 | Strain Relief Power Cord | (German) |
A034631-01 On/Off Switch Assembly ‘A035659-01 Access Panel Assembly AS A035663-01 19" Color TV Monitor Assembly (includes wood shelf) A035664-01 23” Black-and-White TV Monitor Assembly (includes wood shelf)
| A035791-01 or -02 | Isolation Transformer | (for color monitor only) |
| A035793-01 | Monitor Shorting Plug | (for b&w monitor only) |
DP-149-01 Monte Carlo™ Schematic Drawings, Sheet 1 DP-149-02 Monte Carlo Schematic Drawings, Sheet 2 TM-149 Monte Carlo Operation, Maintenance, Service Manual TM-148 Instruction and Service Manual for GO7-901 R.G.B. Color Monitor
| 68-002 | \nterlock Switch | (two per game) |
70-304 18” 15-Watt Cool White Fluorescent Lamp 71-2114 Panel Cartridge Lock Mechanism (for access panel) 7507017 Spacer for Mounting Printed-Circuit Boards
| 78-24012 | 5” Beaded Nylon Tie Wrap | (for Game PCB edge connector) |
79-3210 Single-Pole Fuse Block, with %” x 1/32" Tab 000268-02 Interlock Switch Mounting Bracket 002728-01 Control-Panel Mouniing Bracket 005419-01 Speaker Grille 006870-01 Coin Box Bracket 00788202 interlock Switch Cover 009992-01 Or/Off Switch Cover 034515-01 Upper Retainer Strip 034516-01 Lower Retainer Strip 034536-02 Foam Vibration Damper 035438-01 Molded Dashboard 035509-01 Attraction Panel with Graphics 035634-02 Monitor Shield without Graphics (smoke color) 035635-01 Monitor Shield with Graphics
| 035661-01 | Cardboard Bezel | (for 19" color monitor) |
| 035662-01 | Cardboard Bezel | (for 23” black-and-white monitor) |
035723-01 Product Identification Label 035753-01 Graphics Panel with “GO” Design
Gear Shifter Assy.— See Figure 26
85-22F114 Steering Wheel Assy.— See Figure 25
85-22F 112
035512-0t
003137-01
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any tight to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted of the subject matter thereof unless by Written agreement with or written permission from mecopeats Figure 22 Control Panel Assembly A035657-01 A Parts List 005889-01
75-07054
033127-01
005255-01
Part No, Description
Steering Wheel Assembly—see Figure 25 Gear Shifter Assembly—see Figure 26 62-039 SPDT Momentary Pushbutton Switch, with Red Cap and Light-Emitting Diode 75-010S #10 Plain Flat Regular-Pattern Stee! Washer 75-040S #10 Steel Split Lock Washer 75-07054 Flat Nylon Washer, 0.470" inside diameter x 0.968” outside diameter x 0.075” thick 85-22F112 #10-24 x 3%” Pan-Head Phillips Self-Threading Type F Steel Machine Screw 85-22F114 #10-24 x 7/8” Pan-Head Phillips Self-Threading Type F Steel Machine Screw 000567-01 Metal Backup Plate for Steering Wheel 003137-01 Wood Backup Panel for Steering Wheel 005255-01 Shift Bezel ("H” Pattern) 005889-01 Wood Backup Panel for Gear Shifter 033127-01 Black Molded Switch Bushing 035512-01 Control Panel with Graphics
Figure 23 Game PCB Assembly A035675-01 and -02 A
Figure 23 Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
10-5225 2.2M Ohm, +5%, %W Resistor (R44, 50) 19-315254 250K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 89) 21-101103 .01 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C80, 81) 21-101104 -1uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C78, 79)
| 24-250105, | 1 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C47, 88) |
| 24-250106 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C86) |
| 24-250107 | 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C3, 10, 54) |
24-250225 2.2 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C57) 24-250475 4.7 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C76, 77) 27-250102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C13) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C51, 52, 55, 56) 27-250224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C83-85) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1, 2, 4-9, 11, 12, 14-46, 48-50, 53, 58-75, 82, 87, 89) 31-1N914 75V 1N914 Switching Diode (CR1, 2)
| 33-2N3644 | Type 2N3644 PNP 25V Transistor | (Q1, 6, 7) |
34-2N3643 Type 2N3643 NPN Switching Transistor (Q2) 34-2N6044 Type 2N6044 NPN Darlington Transistor (Q3-5)
| 37-LM324 | Type LM324 Integrated Circuit | (C10) |
| 37-4066 | Type 4066 Integrated Circuit | (A10) |
| 37-556 | Type 556 Timer Integrated Circuit | (C9) |
| 37-74LS00 | Type 74LS00 Integrated Circuit | (F3, F8) |
| 37-74LS02 | Type 74LS02 Integrated Circuit | (H3, N8, Ad) |
| 37-74LS04 | Type 74LS04 Integrated Circuit | (R2, A5, N7) |
| 37-74LS08 | Type 74LS08 Integrated Circuit | (F7, P8, J9) |
| 37-74LS10 | Type 74LS10 Integrated Circuit | (C7, M7, D/E9) |
37-74LS14 Type 74LS14 Integrated Circuit (E3, R10) 37-74LS20 Type 74LS20 Integrated Circuit (C5, P5, L7)
| 37-74LS27 | Type 74LS27 Integrated Circuit | (A8) |
| 37-74LS32 | Type 74LS32 Integrated Circuit | (J3, B7, D7) |
| 37-74LS42 | Type 74LS42 Integrated Circuit | (H2, J2, J7, K7) |
| 37-74LS74 | Type 74LS74 Integrated Circuit | (P2, P3, R3, R5, R8, R9) |
| 37-74LS86 | Type 74LS86 Integrated Circuit | (M5, N5, R6, C/D8, A9) |
| 37-74LS92 | Type 74LS92 Integrated Circuit | (A/B9, B/C9) |
| 37-74LS95, | Type 74LS95 Integrated Circuit | (N4) |
| 37-74LS109 | Type 74LS109 Integrated Circuit | (B3, B5, C8, D9) |
| 37-74LS153 | Type 74LS153 Integrated Circuit | (A7, R7, L9) |
| 37-74LS157 | Type 74LS157 Integrated Circuit | (K2, L2, B4, KS, L5) |
| 37-74LS163A | Type 74LS163A Integrated Circuit | (M2, N2, P4, R4, H4, J4, H5, J5) |
37-74LS164 Type 74LS164 Integrated Circuit (E/F9, F/H9)
| 37-74LS174 | Type 74LS174 Integrated Circuit | (F4, L4, B8, D/E8, L8, M8, F10) |
| 37-74LS175 | Type 74LS175 Integrated Circuit | (M3, J8) |
| 37-74LS191 | Type 74LS191 Integrated Circuit | (D4, £4, D5, E5) |
| 37-74LS244 + | Type 74LS244 Integrated Circuit | (B1) |
| 37-74LS245 ¢ | Type 74LS245 Integrated Circuit | (E2, K4, J6) |
| 37-74LS251 | Type 74LS251 Integrated Circuit | (N9, P9) |
| 37-74LS273 § | Type 74LS273 Integrated Circuit | (A6, P7, H8) |
| 37-74LS367 | Type 74LS367 Integrated Circuit | (F2, K8) |
| 37-74166 | Type 74166 Integrated Circuit | (FS) |
| 37-7425 | Type 7425 Integrated Circuit | (C4) |
| 37-7437 | Type 7437 Integrated Circuit | (C3) |
| 37-7496 | Type 7496 Integrated Circuit | (D3) |
| 37-9316 | Type 9316 Integrated Circuit | (H7) |
t This item may be substituted by part no. 37-74LS241, a type 74LS241 Integrated Circuit (B1) $ This item may be substituted by part no. 37-8304B, a type 8304B Integrated Circuit (E2, K4, J6) § This item may be substituted by part no. 37-74LS374, a type 74LS374 Integrated Circuit (A6, P7, H8)
Figure 23 Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
37-MV5053, Type MV5053 Light-Emitting Diode (CR3)
| 41-3003 | 100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke | (L1-L13) |
62-001 SPST Pushbutton Switch (SW1)
| 66-114P1T | 4Station Single-Throw, Oual-Inline-Package Bit Switch | (SW3) |
| 66-118P1T | 8-Station Single-Throw, Dual-Inline-Package Bit Switch | (SW2) |
73-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2) 81-4302 Nylon Snap-In Fastener
| 90-102 | 12.096 MHz, + 005%, Crystal | (¥1) |
90-6001 Microprocessor (C2) 90-7019 Random-Access Memory (K3, L3, K6, L6) 009114-01 Prograrnmable Read-Only Memory—Sync (N93) 020670-01 Test Point
| 03577801 | Programmabie Read-Only Memory—Alphanumerics | (M4) |
035785-01 Programmable Read-Only Memory—Grey Levels and Color Video (E7)
| 110000-104 | 100 Ohm, +5%, ‘4W Resistor | (R63, 64) |
| 110000-102 | 1K Ohm, +5%, YW Resistor | (R9-13, 16-19, 21, 23, 24, 32, 40, 76-78) |
| 110000-103 | 10K Ohm, +5%, %4W Resistor | (R1, 8, 29-31, 33-38, 57-62, 85, 87, 90, 91, 94-96, 99-102) |
| 110000-104 | 100K Ohm, +5%, %W Resistor | (R105) |
| 110000-105 | 1M Ohm, +5%, %W Resistor | (R6, 43, 49, 81, 86) |
| 110000-122 | 1.2K Ohm, +5%, Y4W Resistor | (R22) |
| 110000-151 | 150 Ohm, + 5%, %4W Resistor | (R27) |
| 110000-153 | 15K Ohm, +5%, %4W Resistor | (R5, 93) |
| 110000-182 | 1.8K Ohm, +5%, %4W Resistor | (R25, 26) |
| 110000-222 | 2.2K Ohm, +5%, %4W Resistor | (R41, 54) |
| 110000-223 | 22K Ohm, +5%, %W Resistor | (R103, 106) |
| 110000-224 | 220K Ohm, +5%, %4W Resistor | (R45, 48) |
| 110000-271 | 270 Ohm, +5%, %W Resistor | (R14, 15) |
| 410000-273 | 27K Ohm, «5%, %4W Resistor | (R92) |
| 110000-331 | 330 Ohm, + 5%, %W Resistor | (R2, 4, 53) |
| 110000-332 | 3.3K Ohm, +5%, %W Resistor | (R82) |
110000-333 33K Ohm, +5%, %4W Resistor (R97) 110000-334 330K Ohm, +5%, %W Resistor (R84)
| 110000-392 | 3.9K Ohm, +5%, %4W Resistor | (R42) |
110000-471 470 Ohm, +5%, %4W Resistor (R3, 28, 51, 52, 65-75)
| 110000-473 | 47K Ohm, +5%, YW Resistor | (R104) |
| 110000-474 | 470K Ohm, +5%, %4W Resistor | (R46, 47) |
| 110000-563 | 56K Ohm, + 5%, %4W Resistor | (R7) |
| 110000-681 | 680 Ohm, +5%, %4W Resistor | (R83) |
110000-683 68K Ohm, +5%, %4W Resistor (R79, 80)
| 110000-821 | 820 Ohm, +5%, %4W Resistor | (R20) |
| 110000-822 | 8.2K Ohm, +5%, 4W Resistor | (R39) |
110000-823 82K Ohm, +5%, %4W Resistor (R98)
For remaining memory components and their part numbers, see list below.
Th Monte Carlo
Figure 23 Game PCB Assembly, continued Parts List
(Locations Shown in Bold) Memory Components and Their Equivalents
| If PROM is bad, self-test will | -01 P.C. Boards | -02 P.C. Boards | If ROM is bad, self-test will |
display the following: (PROMs) (ROMs) display the following:
G
| 03576701 | C1 | 03576301 | C1 | GH _ | (If self-test portion of this |
| H_ | (If self-test portion of this | chip is bad, bottom area of screen | |||
| chip is bad, bottom area of screen | 035771-01 | J/K1 | shows garbage and test pattern |
shows garbage and test pattern will scroll sideways.) will scroll sideways.)
| E | 035768-01 | DIE1 | 035764-01 | DIE | EF |
| F | 03577201 | 1 | |||
| c | 035769-01 | F1 | 035765-01 | F1 | cD |
| D | 03577301 | M1 | |||
| A | 035770-01 | H1 | 035766-01 | H1 | AB |
035774-01 NIP1
| Incomplete test pattern of people, | 035776-01 | E6 | 03577501 | E6 | Incomplete test pattern of people, |
cola stands, trees, bushes, hay cola stands, trees, bushes, hay
| bales, Atari copyright notice, etc. | 035777-01 | H6 | bales, Atari copyright notice, etc. |
(for the correct test pattern see (for the correct test pattern see Figure 6). Figure 6).
| Incomplete red player car (in | 03578101 | M6 | 035779-01 | M6 | Incomplete red player car (in |
center of screen). For correct test center of screen). For correct test
| pattern see Figure 6. | 03578201 | P6 | pattern see Figure 6. | ||
| Incomplete computer car (labeled | 03578301 | BE | 035780-01 | B6 | incomplete computer car (labeled |
number ‘‘0”). For correct test pat- number “0”). For correct test pat-
| tern see Figure 6. | 035784-01 | D6 | tern see Figure 6. |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ROS BI Scees Rey vous Ss
‘(aa a
a
%
pe ® x
ek nse &
eH
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without tne specitic written permission of Atari, Inc... Sunnyvale, CA. This drawing is oniy conditionally issued, and either receipt for possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical intormation shown thereon, nor any right to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, Ine., and for manutacture under the corporation's writien license, no right to repro duce Ihis drawing is granted of the subject matter thereof unless by writlen agreement with or written ermigsion from the corporation.
Figure 24 Regulator/Audio Il PCB Assembly A035435-03 A
Figure 24 Regulator/Audio Il PCB Assembly - Parts List
Part No. Description (Reference Designations and Locations in Bold)
12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 19-100P 1015, -1 Ohm, + 3%, 7W Wirewound Resistor (R24)
| 19-315102 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot | (R8) |
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C1, 4, 12) |
| 24-250478 | 4700 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C29) |
24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23)
| 27-250102 | .001 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C2, 7, 16) |
| 27-250103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C5, 6, 14, 15) |
| 27-250104 | .1 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C3, 11, 20, 21, 27, 28) |
| 27-250224 | .22 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C8, 17) |
| 29-006 | 1 uf Tantalum 36V Capacitor | (C24) |
31-A14F S50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-12)
| 31-1N4001 | SOV Silicon Rectifier 1N4001 Diode | (CR2, 3) |
33-TIP32 PNP Power Transistor, Type TIP32 (Q2)
| 34-2N3055 | NPN Silicon Transistor, Type 2N3055 | (Q3) |
| 34-2N3904 | NPN Silicon Transistor, Type 2N3904 | (Q4, 6) |
| 37-LM305 | 5V Linear Voltage Regulator | (Q1) |
| 37-TDA2002A | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
| 37-7812 | + 12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | —5V Voltage Regulator, Type 7905 | (Q9) |
52-004 Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire with .3" Centers 72-1608C #6-32 x ¥2" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x 4" Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
| 78-16014 | Thermally Conductive Compound | (Q2, 5, 7-9) |
79-58306 6-Position Connector Receptacle (J6, J9) 79-58308 9-Position Connector Receptacle (J7)
| 79-58346, | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 110000-010 | 1 Ohm, + 5%, %4W Resistor | (R10, 19) |
| 110000-100 | 10 Ohm, + 5%, %4W Resistor | (R11, 20) |
110000-101 100 Ohm, + 5%, %W Resistor (R4, 12, 22)
| 110000-102 | 1K Ohm, + 5%, %W Resistor | (R27, 28) |
110000-103 10K Ohm, + 5%, ¥sW Resistor (R13, 14) 110000-271 270 Ohm, + 5%, YW Resistor (R1)
| 110000-330 | 33 Ohm, + 5%, %4W Resistor | (R3) |
| 110000-392 | 3.9K Ohm, + 5%, %4W Resistor | (R6) |
110000-752 7.5K Ohm, + 5%, %4W Resistor (R7)
| 110001-221 | 220 Ohm, + 5%, YW Resistor | (R9, 21) |
| 122000-225 | 2.2 uf Tantalum 35V Capacitor | (C31) |
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atatl, Inc, Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot 72.9580 confers or transfers any right in,o° license to Use, the subject matter of the drawing or any design of technical information shows thereon, nor an Tight 10 reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc, and for manufacture under the corporation's wrt: fen license. no right to reproduce this drawing is Granted or the subject matter tnereot unless by Written agreement with or written permission fromm the corporation
75:07002
“ . SY = 85:22F206
75-990505S.
Figure 25 Steering Wheel Assembly A000598-08 U
Figure 25 Steering Wheel Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold) A009060-02 Steering Printed-Circuit Board Assembly, consisting of the following eight items:
| 10-5331 | 330 Ohm, +5%, %W Carbon Composition Resistor | (R10-13) |
| 10-5392 | 3.9K Ohm, +5%, %W Carbon Composition Resistor | (R14, 15) |
| 10-5471 | 470 Ohm, +5%, %W Carbon Composition Resistor | (R7, 8) |
27-250104 -luf 25V Radial-Lead Ceramic-Disc Capacitor (C2) 29-046 10uf 20V Axial-Lead Tantalum Capacitor (C1) 34-2N3643 Type 2N3643 NPN Silicon Transistor (Q1, 2) 79-58005 10-Position Header Connector 030369-01 Radial Optical Coupler 72-7512 #¥%-20 x %" Fillister-Head Slotted Machine Screw 72-9580 #%-20 x 5" Truss-Head Slotted Machine Screw 75-042 #2 Corrosion-Resistant Steel Split Lock Washer 75-055 #¥% Internal-Tooth Steel Lock Washer 75-07002 Steel Flat Washer, .281” inside diameter x 1.25” outside diameter x .059" thick 75-990505S #%-20 Self-Locking Prevailing-Torque Shallow-Pattern Steel Hex Nut 76-091010 5/8” Inside Diameter Dual-Shouldered Keyed Nylon Journal Bearing 76-092020 1%” Inside Diameter Dual-Shouldered Keyed Nylon Journal Bearing 78-40104 10” Steering Wheel 85-22F206 #256 x 3/8” Pan-Head Phillips Type F Self-Tapping Machine Thread Screw 000599-02 Atari-Logo Cover 000605, Housing 000606 Shaft 000616 Hub Light
Detail of Steering PCB Assembly, A009060-02, Rev. C:
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific wrilten permission of Atari, inc... Sunnyvale, CA. “This drawing is only conditionally issued, and neither receipt for possession thereot confers or lranslers any ight in, oF license to use, the subject, matter of the drawing oF any design oF technical infor mation shawn therean, nor any night to reproduce this, drawing of any part thereo!. Except for manufacture by vendors of Alar, Ine. and for manulacture under the corporation's written license, no right to repro duce this drawing is granted or the subject maiter thereot unless by written agreement with or written permission trom the cciporation EEWING BD
‘al
5800! Traces shown are ™ 7 on opposite side.
000610
78-3002003
76-11375S
000609-01
85-22F608
78-16002 (2 PLACES)
Me
73-7C0307S (pen fe
75-044 NOTICE TO ALL PERSONS RECEIVING THIS RAWING CONFIDENTIAL: Reproduction forbidden without the specific wiitlen permission of Atari, Inc.. Sunnyvale, CA. This drawing 's only conditionally issued, and neither receipt nor possession thereat confers. or transters any right in, oF license to use, the subject ‘matter of the drawing o1 any design or technical infor- ‘mation shown thereon, nat any right o teproduce this, drawing or any part thereot. Except for manulacture 65-0214 by vendors of Alani, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted 9° the subject matter 85-22F 412 thereof untess by writen agreement with or wren permission from the corporation 75-046
Figure 26 Gear Shifter Assembly (“H” Pattern) A000608-03 Ss
Figure 26 Gear Shifter Assembly Parts List
Part No. Description
000610 Shifter Handle 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 73-7C0307S Steel Flat Flange-Head Solid-Shank Rivet, 3/32”-Diameter Shank x 3/16"-Diameter Head x 7/16"-Long Shank 75-044 #4 Internal-Tooth Steel Split Lock Washer 75-046 #6 Internal-Tooth Steel Split Lock Washer 76-11375S 38” Diameter Bearing-Grade Steel Ball 78-16002 Dow Corning Silicone Compound #5 78-3002003 Spring 85-22F412 #4-40 x 34” Pan-Head Phillips Self-Threading Type F Steel Machine Screw 85-22F608 #6-32 x V2” Pan-Head Phillips Self-Threading Type F Steel Machine Screw 000609-01 Gear Shifter Housing (two of these required per gear shifter) 000611 Shift Detent
034740-01
034747-01
65-011C
A034749.01
75-054
034746-01
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reprodteten forbidden without 09556-01 75-035C the specific written permission of Atati, inc. ‘Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, 75-040 the subject matter of the drawing or any design ot tectinical information shown thereon, nor any right to reproduce this drawing or any part thereol- Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing Is granted or the subject matter thereof unless by H 75-9118 written agreement with or written permission from the corporation:
Figure 27 Foot Pedal Control A0347 48-01 A A034741.01
Figure 27 Foot Pedal Control Parts List
Part No. Description
A034741-01 Foot Pedal Base with Bolts A034749-01 “L” Bracket with Actuator Blade 65-011C Single-Pole Double-Throw Low-Force Miniature Switch 72-1412S #4-40 x 34" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 73-3001 Carbon Spring Steel External Retaining Ring, for %” shaft diameter 75-035C #% Plain Flat Wide-Pattern Corrosion-Resistant Steei Washer 75-040 #10 Stainless-Steel Split Lock Washer 75-054 #4 Zinc-Plated Steel Internal-Tooth Lock Washer 75-5128N #10-24 x 134” Round-Head Square-Neck Nickel-Plated Steel Carriage Bolt 75-911S, #10-24 Standard Hex-Pattern Cadmium-Plated Steel Machine Nut 75-9148 #4-40 Standard Hex-Pattern Cadmium-Plated Stee! Machine Nut 78-1709 Dow Corning Molykote G-n Paste Lubricant 000592-01 Spring 003546-01 Rubber Stop 034740-01 Foot Pedal 034746-01 Metal Spacer 034747-01 Pivot Pin
79-4411004 (at F1 thru F5)
A006886-01 AezTSee A009266.01 72-1810S 75-0188 75-048 75-9188
A007444-01
72-1810S 7 41-2003 75-048 75-918S 46-2012501
29-053 46-2022502
46-2038001
72:1810S 75-048 75-918S
78-70501SC
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without tne Specific written permission of Atari, Inc.. Sunnyvale, CA. This drawing Is only conditionally issued, and neither receipt nor possession therect confers or ‘ransters any righ in, oF license to use, the subject matter of the drawing of any design or tectinical inforation shown thereon, nor any right fo repreduce this, drawing or any part thereof, Except for manvlacture ‘ay vendors of Alari, Inc., and for manufacture under the corporation's written license, no right to 1eproduce this drawing is granted or the subject matter thereof unless by writien agreement with or writen permission from the corporation.
A006555-01
Figure 28 Type B Power Supply Assembly A007197-01 K
Figure 28 Type B Power Supply Assembly A007197-01 K Parts List
Part No. Description (Reference Designations in Bold) A006555-01 Rectifier P.C. Board Assembly A006858-01 Voltage Selection Plug (95V—Black) A006858-02 Voltage Selection Plug (110V—Orange) A006858-03 Voltage Selection Plug (205V—Green) A006858-04 Voltage Selection Plug (220V—Red) A006886-01 Type B Transformer Termination Assembly A007192-01 Power Switch Termination A007444-01 Power-In Harness A009266-01 Power Supply Base Assembly 29-053 26,000 uf 15V Electrolytic Capacitor 41-2003 5-Amp Power Line Filter 46-2012501 2¥2-Amp, 125-Volt Slow-Acting Type 3AG Fuse (F3, F4) 46-2013002 3-Amp, 250-Volt Slow-Acting Type 3AG Fuse (F1*, F2*) 46-2022502 2¥2-Amp. 250-Volt Slow-Acting Type 3AG Fuse (F6*) 46-2038001 8-Amp, 125-Volt Normal-Acting Type 3AG Fuse (F5) 72-1810S #8-32 x 5/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 75-018S #8 Flat SAE-Standard Zinc-Plated Steel Washer 75-048 #8 Zinc-Plated Steel Split Lock Washer 75-918S #8 Standard Cadmium-Plated Steel Machine Hex Nut 78-70501SC 2" Diameter Capacitor Mounting Bracket 79-4411004 Panel-Mounted Non-Indicating 3AG Cartridge-Type Fuse Post *NOTE: Fuses F1, F2, and F6 are not part of this power supply assembly and must be purchased separately. They have been listed here for your convenience.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionaily issued, and neither receipt nor possession thereot confers or transfers any right in, of license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any fight to reproduce this drawing or any part thereof Except for manufacture by vendors of Alar, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corporation.
Fiuorescent Lamp— See Figure 21 for Part Number
99-11008 99-11009
Figure 29 Fluorescent Light and Speaker A035658-01
Parts List A 99-11011
035835-01
79-561816P
Part No. Description
48-009 8” 8-Ohm 8-Watt High-Fidelity Speaker 79-561816P_ Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥%2" Clamp 035835-01 Y-Lead Connector
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc., Sunnyvaie, CA. This drawing is only 99-10103 Conditionally issued, and neltner receipt nor possession thereo! confers or transfers any right in, of license to use, the subject mat- 75-948S, ter of the drawing or any design or technical inlormation shown 910098. thereon, nor any right to repraduce this drawing or any part ihereat Except for manufacture by vendors of Alari, Inc., and for manufac ture under the corporation's written license, no right to reproduce Ihnis drawing is granted or the subject matter thereot uniess by writlen agreernent with ar written permission from the corporation 99-10071
eS 75-1408S NN al 99-10095
COIN INLET CHUTE | 99-1097
70-11-47
99-10080
99-10081
75-9448 99-10105 j t COIN MECHANISM SEE PARTS LIST (71-12xxxx) / 99-0102 65-441 72-9603S COIN RETURN 99-10065 SWITCH WIRE CHUTE 9910068 J SEE PARTS LIST a= iar (99-1075 thru sin 99-10074 -1N4002 COIN SWITCH ASSY. as PART OF 99-10047 SEE PARTS LIST 99-1008 99-10082 (99-1042 thru 75-14128 99-1045)
Figure 30 New Coin Door 71-40XXXX
REJECT BUTTON COVER SEE PARTS LIST (99-10055 thru 99-10059) PRICE PLATE
COIN RETURN BUTTON ASSY ‘SEE PARTS LIST oe
SEE PARTS LIST (99-1070, 99-10083 éa10 (99-0012 thru 99-10022) thru 99-0092) -10074
99.10062 72-JA1405B COIN DOOR ONLY SEE PARTS LIST : (89-10009 thru 99-1010) 99-10054 \<™~ \ 72-HA1404C
99-10094 SS
PART OF 99-10074
75-5520B
99-10061 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any fight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for mantacture unde the corporation's wait ten license, no right to reproduce this drawing is Granted or the subject matter thereof unless by 75-915S. Written agreement with or written permission from the corporation. 72-JA1405B 99-10066
99-10051
Figure 30 New Coin Door 71-10XXXX
~~ Figure 30 New Coin Door, continued Parts List
Part No. Description
31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism
71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C. #4x%4" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16" Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75-915S, #'%4-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-944S #4-40 Polymer self-locking steel hex nut 75-948S #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x 2" Slotted pan-head steel machine screw 75-1412S #4-40x34” Slotted pan-head steel machine screw 75-5520B #%4-20x114" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043, Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire)
Figure 30 New Coin Door, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085, German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105, Anti-penny-flip bar
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ee
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm U Distributor C) Operator
Address O Other
City State Zip
TM-149 1st printing
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEF
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States
Second fold
aBpa sip ade
Cut along this line
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BN Ra BE Ren Ren Been Rees 2
WARRANTY
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller’s other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is perfomed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © © s © s « CY SRE ES SAS SS AES
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427
SUNNYVALE, CALIFORNIA 94086 9g
® 408/745-2000 ¢ TELEX 35-7488 ATARI sere comnncsion conn