Q-Bert Instruction Manual (4-83)
Q*bert (US set 1) (Gottlieb, 1982) · Instruction Manual · 44 pages · 45 sections · original scan
Gottlieb
AMUSEMENT GAMES
Q*BERT (GAME GV-103A) INSTRUCTION MANUAL
TABLE OF CONTENTS
SEC. PAGE [B INSTALLATION ....... 0.00.00. 06 00 00c ccc cec eee eeees 1 i INITIALIZATION. .......... 0.0.0.0. 0 cece cece cee eee es 3 Il. GAME OPERATION IV. GAMEPLAY AND SCORING ...................... 4 V. SOUND/SPEECH ..........0. 600.000 eeeee eee 6 Vi. GAME ADJUSTMENTS/OPTIONS ................ 6 Vil. BOOKKEEPING AND SELF TEST ................. 7 Vill. GENERAL INFORMATION .................. ee 9 IX. THEORY OF OPERATION..................0002-0-. " X. | WIRING AND SCHEMATIC DIAGRAMS .......... 12 XI PARTS INFORMATION WELLS GARDNER MONITOR, _ SERVICE AND OPERATION MANUAL (Attached)
“WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”
NOTICE WARRANTY INFORMATION IS LOCATED ON THE INSIDE BACK COVER.
FOR SERVICE, CALL TOLL FREE: 1-800-323-9121; (ILLINOIS) 1-800-942-1620
I. INSTALLATION
MA-216 Ag SOUND/SPEECH ASSY.
GAME ADJUSTMENT SWATCHES (PART OF Al LOGIC BOARD}
ON/OFF SWITCH
on oe
PLAYER SWITCHES c22458 ICAL} JOYSTICK
MA-300 SERVICE PANEL
| STEP/TEST SELECT TEST | VOLUME | COIN |
SWITCH SWITCH = CONTROL METER
COIN CHUTE COIN CHUTE COIN CHUTE FRONT DOOR #2, UGHTS #l INTERLOCK
| MA-375 | 3 | Fa | BRIDGE | FS, | 2 |
BOTTOM PANEL = MONITOR 9VAC RECTIFIERS ISVAC 63V AC
| ASSY. | FUSE | FUSE | FUSE | FUSE |
COIN SWITCH, #
COIN SWiTCH #2
IL. INSTALLATION
A. SET—UP
- Carefully inspect the exterior of the game for any damage which might have occurred during shipment.
- Unlock and open the rear cabinet door.
- Check that all plug in connectors are seated firmly. The connectors are keyed so they will only go in one way.
- Remove the binding strap from the line cord, and install the line cord plate in the groove provided {see photo).
- Cabinet levelers (2) are stored within the cash box for shipping purposes. Install and adjust as necessary.
LINE CORD PLATE
CHECK-OUT
- Check that all cables are free of moving parts.
- Check for any loose wires.
- Check for loose solder or foreign matter on switches and power supply assemblies.
- Be certain all fuses are seated firmly.
- Be sure transformer wiring corresponds to the supply voltage.
- Refer to section VI to make ali the necessary game adjustments.
- Reassemble the game.
- Plug the line cord into a properly grounded 3-wire receptacle ONLY! Cc CONTROL PANEL REMOVAL
2.
3. . Unplug the game.
Unlock and open the coin chute door.
Reach in through the coin chute door and remove the wing nut and flat washer from each of the two carriage bolts which secure the control panel to the game. Remove the carriage bolts.
. Pull the contro! panel back, grasp it at the front edge as far back as it will go (approximately 4”).
. Raise the front of the contro! panel approximately one inch above its supports and lift the entire assembly high enough to disconnect plug A9J2/A9P2.
. Remove the entire control pane! assembly from the game.
. The Joystick and leaf-switches are now accessible for removal or cleaning.
MONITOR REMOVAL . Unplug the game.
. Perform the control panel assembly removal procedure {Section C).
. Remove the outside shield, glass and monitor mask and put them aside in a secure place.
. Unlock and open the rear cabinet door.
- NOTE: The color monitor contains HIGH VOLTAGES delivering LETHAL quantities of energy. Do not attempt to service the Monitor until you have shorted the anode Plug on the picture tube to ground.
. Disconnect the video plug AI7J1, the monitor power supply plug Al2J3/A12P3 and the ground wire from the monitor chassis. . From the rear of the game, remove the one nut and one washer from each of the four carriage bolts used to secure the monitor to the platform.
. Remove the monitor from the rear of the game, being careful to clear all cables from the CRT neck.
. For reassembly, reverse the above procedure.
fl. INITIALIZATION, Ill. GAME OPERATION
I. INITIALIZATION
TURN GAME ON B. The playing field cycles through the follow Immediately, the coin chute lamps and the 1. High Game to Date screen
speaker marquee lamp will turn on. 2 Instruction Set
- Game Play Cycle AFTER A TEN SECOND DELAY A. The attract mode appears on the screen.
I. GAME OPERATION
| A. | GAME START | Cc. | SECOND PLAYER |
- Insert coins into coin chute. 1. Additional player is indicated by
| a. Coin chute tune is played. | 4 | the words “PLAYER 2” and a zero |
| b. Total credits are displayed on screen. | ‘ | in the second piayer’s display. |
- Press one or two player button to start game.
| a. Demonstration scene displayed | D. | “Q* BERTS”/EXTRA “Q*BERTS” |
OM SCREEN: 1. Each player will begin with three
b. Total Credits are decreased by one. “QsBert” lives. (Dependent on
c. Game initializes. Option/Parameter settings.)
- Extra “Q»Berts” are earned by
| B. | FIRST PLAYER | achieving certain score levels. |
1, The first player's score displays a zero. (Dependent on Option/Parameter
- The other player's display will be blank. settings.)
IV. GAME PLAY AND SCORING
HOW TO PLAY
The object of the “Q*Bert” game is to change the color of the top of the cubes to the designated color by hopping onto them. When all the cubes in the pyramid have been changed to the designated color, the screen will advance to the next Round, with “OxBert” starting back on the top cube. At the beginning of each Level, there will be a short demonstration cycle with the “Q*Bert” character hopping around four cubes to explain to the player the play action of each Level. Each Level consists of four Rounds.
The game play starts with the player-controlled “QxBert” character appearing at the top of the pyramid. The joystick will move “Q*Bert” from cube to cube by hopping in any of four diagonal directions. “Q»Bert” can move anywhere on the
pyramid, but jumping off will kill him. Hopping on
the rotating disk will take “Q-Bert” back to the top of the pyramid. In the first two Rounds “QxBert” will have to avoid touching the red and purple balls. These deadly objects drop randomly onto the second-from-the-top level and bounce downwards. The red balls will fall off the bottom but the purple ball will stop at the bottom and hatch into “Coily”, the snake which chases “Q+Bert”. To destroy the snake, lure him to the
edge, then jump unto a disk. The disk will take
“Q*Bert" back to the top and “Coily” will fall off, awarding 500 points.
Starting at the third Round, other characters come into play. The green characters or objects are safe to hop onto and will award points. All other Objects are deadly to touch. In the third Round the red balls will stop falling, but two purple characters, “Ugg” and “Wrong-Way”, will appear at the lower portion of the pyramid and travel sideways and upwards. They will not chase “QxBert” but will move randomly to get in “Q»Bert’s” way. In the third Round and every Round after, based on an internai timer, a green ball will appear and bounce down from the top of the pyramid. Hopping “Q*Bert” onto the green ball will award 100 points, and freeze all the characters on the screen for a few seconds, but “QxBert” will still be able to move to complete the color changes.
During the third Round of play, two green characters, “Slick” and “Sam”, will appear, based on the interna! timer. They will drop onto the second level from the top and hop randomiy downwards. If they hop onto a cube that “Q*Bert” has already changed the color of, the cube will change to a different color, to thwart “QsBert". Hopping “O*Bert” onto “Slick” or “Sam” will stop them and award 300 points.
Throughout the remaining Rounds, all the characters and objects will appear in random combinations with increasing speed.
To add variety to the game, the disks will change positions every Round, and in the higher Levels the number of disks will change. (See Round Progression Chart.}
During Level Two, the play action will increase in difficulty from changing the Cubes to one color, to changing the coior of the cubes twice. This means that each cube would have to be hopped on twice to change the pyramid to the designated color, completing the Round.
Starting at Level Three and for all remaining Rounds, and Levels, the play action will become more difficult. The object remains to change the cubes to the designated color, but if “OQ*Bert” hops on any cube, that cube will change color. So even if the cube has been changed to the designated color, it will change again. There are also Bonus points awarded at the end of each Round for successfully completing the Round. The Bonus for the completion of the First Round is 1,000 points. This Bonus will progressively increase each Round by 250 points to a maximum o7 5,000 points at Level Five.
CONTROL PANEL INSTRUCTIONS
Goal: Change the tops of all cubes to a new color by hopping onto them.
© Joystick moves “Q*Bert” from cube to
cube. Hopping onto a disk will take you
back to the top. © All green objects are safe to hit. All other objects are deadly.
@ Destroy the snake by leading him to the edge, then jumping on a disk. © Stay on pyramid! Only jump off to use a disk.
IV. GAME PLAY AND SCORING
ROUND PROGRESSIONS
The following chart lists round progressions for “Q»*Bert”.
Commencing with Level V all characters will appear in each subsequent round. The number of disks and the Round Completion Bonus will remain the same value for the rest of the game. The characters and play action will gain more speed with each increased level of play.
ROUND COMPLETION BONUS
ROUND DISKS CHARACTERS ON SCREEN
Red Balls, Coily Red Balls, Coily Coily, Green, Ball. Ugg/Wrong way, Slick/Sam Red Balls, Coly, Green Ball, Slick/Sam Coily, Green Bali, Ugg/Wrong Way, Slick/Sam Colly, Green Ball, Ugg/Wrong Way, Slick/Sam Red Balls, Coily, Green Ball, Slick/Sam Red Balls, Coily, Green Ball, Ugg/Wrong Way, Slick/Sam Red Baills, Coily, Green Ball, Slick/Sam BUNS LEVEL |
LEVEL Hi eWN= LEVEL I!) | Coily, Green Ball, Ugg/Wrong Way, Slick/Sam BUNA Red Bails, Red Bails, Colly, Green Bali, Ugg/Wrong Way, Slick/Sam Coily, Green Ball, Ugg/Wrong Way, Slick/Sam Red Balls, LEVEL IV euoolwurelNNWww/ NNN
BUNS Red Balts, Red Balls, Red Balls, Coily, Green Ball, Slick/Sam Coily, Green Ball, Ugg/Wrong Way, Slick/Sam Coily, Green Ball, Slick/Sam Coily, Green Ball, Ugg/Wrong Way, Slick/Sam
LEVEL V RWNH In Level V all characters will appear in each Round
LEVEL VI THRU LEVEL IX wuunluoon All characters will appear in each Round in Level VI thru Level IX
SCORING
© Luring “Coily” off the edge Scores 500 points and clears pyramid of characters
© Hopping onto “Slick” or “Sam” Scores 300 points
© Hopping onto Green Ball Scores 100 points and freezes characters but not “O«Bert’” ® Changing cubes to designated color Scores 25 points
® Changing cubes to intermediate color (in Level Il or Up) Scores 15 points
© Unused disks Scores 50 points
® Round Completion Bonus See Round Progression Chart
WHO'S WHO and WHAT'S WHAT
w ‘color Hopping on
Qsbert Slick takes Q.bert back tothe top
V. SOUND/SPEECH, VI. GAME ADJUSTMENTS / OPTIONS
V. SOUND/SPEECH
ATTRACT MODE
OCCURENCE SPEECH
“HELLO, I'M TURNED ON” When game is powered up.
GAME MODE
OCCURENCE
When “Q*Bert” is killed. When the characters “Slick/Sam” and “Ugg/Wrong Way” are present.
When player has finished entering his initials on high score table. SPEECH
(Garbled Nonsense Speech)
“BYE, BYE”
Vi. GAME ADJUSTMENTS/OPTIONS
A. CONTROL BOARD SWITCH ADJUSTMENTS DEMONSTRATION MOOE* : =. INFINITE LIVES NORMAL PLAY SWITCH 1
ATTRACT PLAY «NO SOUND =. SOUND
NORMAL/FREE cose. FREE PLAY . NORMAL GAME
GAME MODE <=» COCKTAIL sees UPRIGHT
- NOT USED
_—_________ NOT USED
IN DEMONSTRATION MODE THE PLAYER WILL HAVE INFINITE LIVES AND CAN PROGRESS THROUGH THE ROUNDS BY HITTING EITHER START BUTTON. SOUND ADJUSTMENTS The audio output is controlled by the potentiometer mounted on the service panel assembly (located inside the coin mechanism door).
Turning the potentiometer counter-clockwise will decrease the volume. Turning it clockwise will increase the volume.
MONITOR ADJUSTMENTS Normally, few if any adjustments are required for proper monitor operation. However, after any major repairs to the monitor chassis refer to the attached monitor manual.
Vil. BOOKKEEPING AND SELF TEST
BOOKKEEPING
The battery back-up bookkeeping functions of QsBert (GV-103) are contained in Self Test steps 3 and 4. These are in addition to the electromechanical coin counter located inside the front door panel. Every time a coin is inserted into a coin slot, the counter is energized, incrementing the count.
SELF TEST
The self-test consists of six functions which may be used to identify problems in the video system and to change program parameters. The self-test mode is entered by setting the self-test toggle switch located inside the cash door to “TEST”. A selection of available tests is displayed on the monitor. To return to the GAME mode at any time, the operator needs only to set the toggle switch back to “GAME”.
Selection of tests is done with the push button switch labled “SELECT”. Upon entering the test mode, a flashing arrow points to the first test selection. Momentarily depressing the “SELECT” button will advance through each selection one by one. When the arrow is pointing to the desired test, the operator may begin that test by pressing the “SELECT” button and holding it down until the test appears on the screen. Once a test has been selected, the operator can return to the selection list by holding down the select switch until it re-appears. The eight tests are as follows:
- MONITOR ADJUSTMENT Four patterns can be displayed on the screen for adjusting monitor color, brightness, contrast and convergence. The patterns are: Color bars, a cross-hatch, a gray scale, and a dot pattern. By momentarily pressing the select switch, the operator may cycle through the four patterns.
- DIP SWITCHES A functional description of the eight Dip Switches located on the Logic Board Assy. is displayed. Changing any switch will cause an immediate update of the description displayed on the screen.
- DISTRIBUTIONS Selecting this test will first display a distribution option. The distributions can be reset to zero by pressing either start button, and then pressing the SELECT button momentarily. Following the latter, a cleared distribution screen will be displayed; or the distribution screen can be viewed without clearing it by pressing the SELECT button momentarily when in this test mode. The distribution screen will show three categories of counts — 1) Level/Round; 2) Time;
- Score. These categories, used with the coin meter count, can be used to derive the game percentages and averages.
The categories are presented in three vertical pairs of columns displaying the level of category and the number of players to attain that level. The left category is a list of the Levels and Rounds up to Level 3, Round 4. Next to each Level/Round is the number of players to reach that Level/Round. The middle two columns are a list of game durations in 45 second increments and the number of players to last that long next to it. The right two columns are a category of piayers scores in increments of 3000 points and the number of players to attain that score level.
At the bottom of each category will be displayed the number of players to go beyond the defined levels. The number of players in each category level are independent of the other categories, so each player will be listed once each for Level, Time and Score. The number of players in each category level are given in 4 digit values only, so the distribution table should be reset every two weeks or so to insure that meaningful information will be contained in it.
- OPTIONS/PARAMETERS This test will allow the operator to view and change all game options on one screen. During this test the screen will display seven operator adjustable options. Pressing the “SELECT” button momentarily will advance the arrow to the next option desired. When the arrow is pointing to the appropriate option, the
Vil. BOOKKEEPING AND SELF TEST
Operator can then adjust that option by pressing either of the control panel start buttons, to select the desired value for each option. A. Reset High Score Table — Pressing either start button will reset all 23 high scores to random values and initials starting at 3000 Points for No. 1. B. Factory Preset — Using this option will reset all the following options to the factory recommended levels: 1 Coin/! Credit, 3 Lives, Normal Difficulty, Ist Extra Life at 8000 Points, Each additional life at each subsequent 14000 Points. C. Coin/Credit Combinations — Pressing either Start button will cycle thru three coin combinations:
- 1 coin = 1 play
- | coin = 2 play
- 2 coin = 1 play D. Lives Per Game — Pressing either Start button will cycle thru three choices; 3 Lives Per Game, 4 Lives Per Game, 5 Lives Per Game.
E. Difficulty — Two choices may be selected with either Start button; Normal or Hard.
F. 1st Extra Life — There are six choices, from 6000 Points to 11000 Points, that will be displayed by pressing either Start button. Any value can be chosen to award the first extra life by stopping on that choice and then selecting the next option. G. Each Additional Life — There are six choices, from 12000 Points to 17000 Points, that will cycle thru by pressing either Start button. Any value can be selected to award additional lives at each subsequent Point level chosen.
MEMORY For each RAM memory chip; a green check (v} or red (x) appears signaling that the chip is good or bad respectively. For each ROM memory chip, a check sum is displayed. If you have a suspect ROM, refer to your distributor for the correct check sum number.
SWITCHES A colored square is displayed for each player button. Pressing a button causes the appropriate square to change color. For each coin mechanism, a digit is displayed {initially 0). Inserting a coin into a coin chute will increment the appropriate value without affecting the coin meter.
SOUND TEST After selecting this test a count will appear on the screen representing the various sounds that are produced by the Q-Bert game. There will be 36 different sounds produced and the screen count will stop at 41. Pressing either Start button will suppress all sound output and speed up the count so a particular sound can be sought out and checked.
OBJECT PRIORITY Visual inspection must be used to determine the priority of two or more objects occupying the same area of the screen; that is, which objects appear to be in front of others and which are behind.
A total of 62 identical objects are placed on the
screen in 4 rows. Each object overlaps another such that the first object appears to be in front, and succeeding objects appear to be placed behind all previous ones. When this display is completed, the procedure is repeated such that each new object appears to be in front of all the previous ones.
Vill. GENERAL INFORMATION
A. PRINTED CIRCUIT BOARDS ARE DESIGNATED AS FOLLOWS:
AI Logic Board Assy.
A3 Power Supply Assy.
AG Sound/Speech Assy.
A8 Filter Board
B. WIRE COLORS ARE SHOWN AS NUMBERS:
O Black 5 Green
1 Brown 6 Blue
2Red 7 Purple
3 Orange 8 Slate
4 Yellow 9 White
For example, 688 is a BLUE- SLATE-SLATE striped wire.
C. FUSES
BOTTOM PANEL
| Fl | Primary Power | 4 Amp SLO-BLO |
| F2 | 6.3 VAC | 3 Amp SLO-BLO |
F3 Monitor 2 Amp SLO-BLO
| F4 | 9 VAC | 10 Amp SLO-BLO | |
| FS | 15 VAC | 1 Amp SLO-BLO | |
| Fo | Knocker | +30VDC | 1 Amp SLO-BLO |
POWER SUPPLY ASSY. {A3)
| Fil | +SVDC Source | 5 Amp SLO-BLO | |
| F21 | Sound/Speech Assy. | +30VDC | 12 Amp SLO-BLO. |
| F31 | Sound/Speech Assy. | +12VDC | Ye Amp SLO-BLO. |
| F32 | Sound/Speech Assy. | -12VDC | % Amp SLO-BLO |
| F41 | Coin Meter | +20VDC | 1 Amp SLO-BLO. |
VIN. GENERAL INFORMATION
POWER SUPPLY SPECIFICATIONS
LOCATION PROTECTION
Logic Board Assy. Voltage adjustable. GAmps over-voltage protection and fused for over-current protection. Sound/Speech Board 1.5Amps fused for over-current protection. The reference for this circuit is a 1N5363 +30VDC Zener controlling the base of an emitter follower pass transistor.
+12VDC -12VDC Sound/Speech Board 100 milliamps fused for over-current protection. The plus and minus 12 volts supplies are the 7812 and 7912 IC regulators respectively. Coin Meter +20VDC Full wave rectified unfiltered voltage, fused for over-current protection.
Coin Chute Lights +4.5VDC Full wave rectified unfiltered voltage, fused for over-current protection. IOOVAC or NISVAC, GOHZ Monitor and Marquee \solated, fused AC voltage.
IX. THEORY OF OPERATION
INTRODUCTION The character based graphics system designated GG-IIl has two main subdivisions. The first subdivision is the Central Processor Unit (CPU) which has three partitions: a. Microprocessors b. Memory c Input and Output ports (I/O)
The Intel 8088 microprocessor is used and 32K bytes of memory is reserved for programming space and has 5 input ports and 5 output ports. The second subdivision is the video state machine which generates and controls the video signal to the monitor. The state machine has three partitions: a. System Clock (CLK) b. Foreground generator (FGND) c_ Background generator (BGND)
The system clock ts driven by a 20MHZ crystal, divided down for a SMHZ dot clock.
All inputs and outputs including the video control and general purpose |/O are memory-mapped, {i.e. everything within the system can be addressed in a single segment of 64K addresses as memory).
The video control unit is divided into an “objectoriented” foreground driver and “character-oriented” background driver. The screen resolution is 256 pixels horizontally, and 240 lines vertically for both foreground and background. The CPU communicates with the foreground driver and background driver by writing data into the designated memory areas in a certain format The foreground is designed to display moving objects on the screen with a minimum overhead to the processor. The game programs will only have to specify the vertical and horizontal! position and the object select number to the foreground driver. The background video supplements the foreground with relatively static figures on the screen. The CPU specifies all the character positions on the screen with desired “character ” patterns.
A 5MHZ system clock drives a 9 bit horizontal dot counter and an 8 bit vertical line counter. The horizonta! counter counts from O to 255 during active scan line and 256 to 317 during horizontal bianking time. When the horizontal counter reaches 317, the horizontal counter resets to 0. At the beginning of the horizontal blanking time (horizontal counter = 256) it increments the vertical counter. The vertical counter counts from 0 to 239 during active vertical scan time and 240 to 255 during vertical blanking time.
The battery backup system supports two battery RAM'‘s that store all of the bookkeeping functions. The battery is maintained at a +3.6V reference by a trickle charge supplied on the logic board regulated by a current limiting resistor. If the AC power to the game is interrupted, the battery allows the RAM’s to store the data contained in the Distrubutors table and the Options/Parameters screen. X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
TABLE OF CONTENTS
PAGE
LOGIC BOARD ASSY. (A1) COMPONENT LOCATION AND PARTS LIST ........... 0.0205 s ese eee ee 13 SCHEMATIC DIAGRAM (SHEET 1 OF 3) . .. 16 SCHEMATIC DIAGRAM (SHEET 2 OF 3) . 18 SCHEMATIC DIAGRAM (SHEET 3 OF 3)
POWER SUPPLY ASSY. (A3) COMPONENT LOCATION AND PARTS LIST SCHEMATIC DIAGRAM
SOUND/SPEECH ASSY. (AG) COMPONENT LOCATION AND PARTS LIST .. SCHEMATIC DIAGRAM
PRIMARY POWER/FILTER BOARD/ INTERCONNECTION DIAGRAM .......... 2.2.05 0200s cece eet 30
LOGIC BOARD ASSY. {A1),
MISCELLANEOUS ELECTRONIC
REFERENCE
Batt C1-Ci6
C25, C26
C27 C3134
cst C52 ‘ALL UNMARKED CAPACITORS ‘ALL POLARIZED UNMARKED CAPACITORS, D2 fog Det ar-a4 81-087 RI-RIG R37, R3B R39
R89, RIO
R100 RIO} RI02 R103 RI04 SIP 1, SIP 2, SIP 4 SIP 71, SIP 72, SIP 73 X-TALI XTAL 51 PARTS LIST
COMPONENTS
DESCRIPTION
Battery, 3.6V Capacitor, 0.1 UF SOV AX. CR. +80%-20% Capacitor, 100 UF, 25V EL-AX Capacitor, 0.1 UF SOV AX. CR. +80%-20% Capacitor, 100 UF. 25V EL-AX Capacitor, 0.1 UF, SOV AX. CR +80%- 20% Capacitor, 100 PF, 100V CMD 5% Capacitor, 0.1 UF, IOV CMD 5%
01 UF, 50V AX. CR. +80%-20%
10 UF, 25V AX. TANT. 10% Diode, 1N4454 Diode. 14733 Diode, 1N4148 Transistor, 2N6044 Transistor, MPSA70 Resistor, 470 OHM, 5% ‘AW Resistor, 330 OHM, 5% AW Resistor, 130 OHM, 5% ”W Resistor, 270 OHM, 5% YAW Resistor, 510 OHM, 5% /4\W/ Resistor, 130 OHM, 5% “WW Resistor, IK OHM, 5% “W Resistor, 330 OHM, 5% VW Resistor, 1K OHM, 5% “WW Resistor, 560 OHM, 5% /4W Resistor, 1K OHM, 5% WW Resistor, 1K OHM, 5% AW Resistor, 1k OHM, 5% AW Resistor, IK OHM, 5% AW Resistor, IK OHM, 5% ”\W Resistor, 820 OHM, 5% %W Resistor, 100 OHM, 5% AW Resistor, 15 OHM, 5% AW Resistor, 180 OHM. 5% V4W/ Resistor, 15 OHM, 5% AW Resistor, 180 OHM, 5% “W Resistor, 15 OHM, 5% YAW Resistor, 160 OHM, 5% AW Resistor, IK OHM, 5% 14W Resistor, 2k OHM, 5% “AW Resistor, 1K OHM, 5% vA Resistor, 470 OHM, 5% '4W Resistor, 240 OHM, 5% ‘AW Resistor, 2K OHM, 5% “AW Resistor, 1K OHM, 5% AW Resistor, 470 OHM, 5% AW Resistor, 240 OHM, 5% %W Resistor, 2K OHM, 5% “WW Resistor, 1K OHM, 5% '4W Resistor, 470 OHM, 5% '4W Resistor, 240 OHM, 5% 1«W Resistor, Dip. 4.7K, 9 Pin Resistor. Dip. 1K, 9 Pin
Crystal, 15 MHZ Crystal 20 MHZ Dip Switch 20 Pin Dip Socket 22 Pin Dip Socket 24 Pin Dip Socket 28 Pin Dip Socket 40 Pin Dip Socket X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
LOGIC BOARD ASSY. (A1), COMPONENT LOCATION
D E i F S
ar
t LLU
aeaseHaReagal
13 14
A, AI RRRELSERE
Ay
G2, 3, GS LOGIC BOARD ASSY. [A1}, PARTS LIST (CONT.)
INTEGRATED CIRCUITS
| DESCRIPTION | PART | REFERENCE | DESCRIPTION |
No.
| Logie Board Assy | Mas7a | G7 | 74157 Quad 2-npit mutiplexer |
| 8204 CLK Orher | xoa7e | 8 | 741574 Dual D-ype fp Nop |
| 741502 Quad Dinput“NOR’ gate XO428 | GF | 745157 Quad 2-nput multplexer | |
| 7416 Syrerronous &-bit counter | XO-192 | GIO | 7415245 Octal bus vascener |
| 7a1S377 Ocal -D" Fp Flop | X097 | Gil | 7418376 Ocal O-ype Mp Nop |
| 088 CPU | x0490 | © Gi2 | 7A1SIS7 Quad 2-input mbps |
| 7415373 Octal D-ype tip fp | -XO445. | GIB. GH, GIS | 7489 64-bit RAM |
| 7A1S367 Hex 3state bufer | —-XO444 | Gib, GIT | PALSI74 Hex D fp fop |
| 741508 Quad 2input “AND” gate X0-86 | HZ, HB, KA | 745189 64-bit RAM | |
| 74HCIB8 Decoder/éemuiplerer | XO-190 | HS, HE | 7416 Synchronous presetable |
| 7415139 Dual of decoder | XO-419 | ‘inary counter | |
| 7415138 I of 8 dedocer | 50-437 | HT. HO,H8, MIO. 741SI57 Quod 2inpue mutipleer | |
| 7415240 Octal Bufler/ine diver | X09) | HI | 7815260 Dus Sanput “NOR” gate |
| 7415373 Ocal Deype tip op | XO-485—HIZ | 7415298 Ovad 2-port register | |
| 741S245 Ocal Bus vansceiver— | XO-79 | HIB | 7A1SI57 Quod 2rput mutpleer |
| PAM g etisiPs | xoi) | HF | 4781500 Quad 2input |
| RAM | 6164 | XOu81 | “NANO” gate | |
| RAM 221282 | xO19 | HIS | 741530 8 input “NANO” gate |
| RAM 321282 | xO | HIG, HIT | 741586 Dual 2input excise |
| ROM 9 2764 aK x8 EPROM | —_XO-489 | “OR gate |
ROM 1 2768 OK xB EPROM — XO489 I 2 3,
| ROM 22764 8K x8 EPROM | XO489 | 5, 6 | 745189 64-bit RAM |
| 7ALSIB9 Dual of 4 Decoder | XO-419 | 741504 Hex inverter |
741532 Quad 2-input “OR” gate 7408 Quad 2 input “AND” gate
| 74157 Quad 2-input multiplexer | XO-118 | 93422 256 x 2 bpolar RAM |
| 7A1S374 Octal ype lip top | 0-96 | 7A1S02 Quad 2ingut “NOR” gate |
| 7415264 Ocal uterine crver_ | XO? | JA1S74 Dual O-ype tip flop |
7418157 Quad 2input mitipererXO-390 7407 Hex buter/arver
| 7aLS86 Quad 2-nput exh | XO-435 | 741530 8 input "NAN" gate |
“OR gate ‘7ASI6! Synchronous presetable
| 7415283 4Di binary ful adder | XO-95 | RY | ety |
74S161 Syrerronous presetable XO-488 yp fp Hop binary counter 0 2764-3 8k x B EPROM
| 93419 64 x9 pola RAM | X99 | FGI 2764-3 8K x8 EPROM, |
7415283 40: Brat full adder XO-95 FG2 2764-3 8K x8 EPROM
| 741530 Banput “NANO” | x0-432 | FG3 2764-3 BK x8 EPROM | |
| 401 Kx8 RAM | x03 | 7515157 Quad 2anput mutiperer | |
| 7a1S245 Octal Bus Transceiver | XO-79 | 7415260 Dual Spat | |
| 4801 1K x8 RAM | x0.193 | "NOR" gate | |
| 27B2A(BGBI4K xB EPROM | —-xO-485 | KIB | 741532 Quad 2-input “OR” gate |
| 2732A/9GI)4K x8 ROM | —-xO-485— | KF | erty |
74186 Quad 2inputexchsve x
| “or oem | 455 | as | 74504 Hes inverter |
| 7415273 Bie register | xo | Ki | 741S20 Dual 4-nput |
741520 Dual 4aeput (NAND" gate XO-430 "NANO" gate
| 7415283 4-it binary ful adder | XO-95 | KIT | 74SI6t Synchronous presetale |
| 7ALS32 Quad 2inpur "OR gate | XO-433 | binary counter | |
| 741504 Hex verter | ZOMG | 415, 15,17 | —4LSI66 OIE regiter |
| 74SI61 Syrchronous presetable | XO-488LIO | 741574 Dual tip flop | |
| binary counter | ur | 741520 Dual input | |
| 741586 Quad 2inpur excuse | XO-435 | “NANO gate | |
| “OR gate | u2 | ZALSI6t Synchronous presetable |
binary counter
| 741SIS7 Quad 2input mubploer | X0-390 | U3 | 74574 Dual Deype pos. edge |
‘ALSI6I Srctronous presetable XO-440 tg fip op (TL ony)
| binary Counter | ua | 74504 Hex verter |
PART No. xons xo43 xo-14 xO-79 x06 0-390 xo-88 xO-442 xo-89 0-488
0-390 x03 x08 0-390 x0427
x0-432 xO-435
xo-89 xO-418 xO-433 xO-408 0-100 x0-428 xO-434 0-384 xo432 xO-488
x0-58 x0-489 x0-489 x0-489 0-489 0-390 xo93
0-433 xO-86
x0400 0430
xo-488
xo3m x04 0-430
x0-440
xo-a7
x0-400 X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
D880 Regu)
Sy uae Pieou API AML zl Fo ln fee *] Vee [WR Vee SCRATCH PAD MEMORY a)
bees te
WR Vee Wimal =e] é
ahs b g i FROM Bt-17 «VERT BANE, 2g ssv-£8} Bs
Bs e $ g
SorsEL, FROM 67-104 CORSE > Rom a5-3 « SoSRSEEL ts 2 Feom 6-7 «28S8E ty 5 Fea 26-9 -ERSEE > 5. eetn 84-3 «WT 6 Feo 84-74-2211 10 Fon 48-5 ARIZ BLIP > 29 ¢ Romig ga NEB ELOP Ts 3 ream hice ALB PRON! 2g FROM APE 4
+ i a . woe ADDRESS BUS
Joo Joo
| Veo FEST MN ag) | whe | ae | AB | ara Bus—_4 |
| ae | ag | Sh | ater | |
| clk | AG | le | weessea fs | 38 |
ag ep uaten 5
| EB | era | 4 |
BS eK ca
| weser | [2 | ro | |||
| aoe | He | fo Xx | 1 | oe | =i |
| weawy | a | THC | ile | ||
| nH | tte taten? | Sebi | a | ig | |
| Be | ht | peresrs | Sas | ane | PROGRAM MEMORY |
| a | wo | a | Ae | ||
| RS | ia | rc | lar |
NMt isf alk. ina He LDA $59 wat ben Pe
wre B A
| oo | ra | fe | ||
| pei | ettsv DC | " | off | n |
CSauRee) wales A
Ee 78 bane —-
} ad 8: L 3 . aire xe) Ci
| weit | + | th | Fa)2 | 9 | T |
| ee | ile: | Bry Sebe | —o |
3 falas BU Ey
| & | was | ear |
wake Har cane
| : | e | isonet ab |
| 18 | 2-f | a ama |
fiifiih a2 cg) Wekekr eke lies ke
| y | So | BiG | aft | Hips | 87 | |
| ‘ | A | ai | 14 | |||
| Hi | an | Seb | eperek za | |||
| ¥ | wa | Ta | ||||
| 18 | Ki | FFF | Pt oven | re) a | aw | a |
| 8 | set | Sfmuen | Hef, | 4s | ||
| 4 | crolen les eg | = | sul, BIO ¢ | 3 | —_ | |
| 4169. | FP | Levels eo | YT | Ae | ||
| Kg | CP) oe | ATE | TPH 15 yg MD ah ¢ | |||
| & | Cye | TROCKBALL INPUT | 76 Sec |
OM BS cy INTERFACE BOARD col 1 ee ASSY. oprowaty To ra/e4-10
| i | ay! | SOCKET |
| sled Z arexs)
| esteege | fez} | 3c | ain | a | |
| 2 | Stora: | A | bo | He | oi |
| ea | [oes | es BIZ | |||
| i | Spee | g | fo | ar BOER | |
| i | borer | ee | Fons eho | ||
| 2 | pean | aes | ie atSeahe | ||
| f | Stease | co | |||
| ec | =m | ec | =o |
ESEEIP ae Y ove ewtren GFN) 1p PS, FROM AlPI-b -VESTSING | 5 12, FROM AlPi-d #VOE2 GND 1 1g
et
me
i ans STS Terk a cae, BAe e- KNOCKER, Phan apie «HOR SXNELS 1g Avr eam a1prage SSP —— ts ALPE From Apieiee eS 17 Fon aiese 28 1S 18 “16 AIPI-G
as One
DESIGNATIONS PI THRU PE AEE INDICATED FOR REFERENCE ONLY.
LOGIC BOARD ASSY. (A1}, SCHEMATIC DIAGRAM, SHEET 1 OF 3
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS A |g ADDRESS BUS _ D a7 DATA BUS C13, CA C15, COLORRAM
| 2 | Fore ving 3 | "5 | pet | age |
| Four vb} 4 | is | wesiro | ||
| Fore Woks | Ree | = | ||
| eae Ves 1 | react verte | © | bec |
A e
| Tor ice vint | yet EM val | s |
Back vibe 5 70] % Bickvos al" wo | RED R91 worse ose be mesar0 ae
| H5¢H | La | 15 | |
| inde BUFFER | igo | es | |
| 2apRESS | us | P | |
| 3 | eountre | HTraavAlO | a5 |
| LINE ADDRESS. | PARALLEL | ; | t |
ae,
| opeyh | JumPeR | S85 | "| areen | |
| praery (ale | OPTION FOR | Sa | a | |
| raLS02 | Sener. | iB | ||
| rg | Ine Line | eee | ||
| lat Burren | 3 | Miser | ||
| E | wep | qpet | 285 | |
| st | it | ry | se22, | BRR |
a
| aR | bad | Say | ie | ene |
re] RAZ IF] ° Discuaaie Grohe
| te! | UNTER, | gore | ao | BLE, |
| 200NS | Reo | PSA | ||
| UNTER | : | gee | eyos7 #88, |
a 2 THR Sena OAL
| — | aus sire | on | ||||
| uN | pene erie: | oft | a | TAN ADDRESS BUS | ||
| = | raise | L206 3 | song oft | a | — | |
| Ke tHru KB | BRAZ to] | SBR 74) | gf 2280 | ane ¥W | OsRAe—T | |
| a | os | oTeas—e | ||||
| TRTORELE_2_Laton oux} | b | RAB FOREGROUND ORTEGT ROMA | He aa | ee She yyy 01 FEEL | pasir | ie 2 |
| HHS 11] | BERAG 4 | 13 BRO3 | * | |||
| ae | cones 3)* | bed STS | wea |
as aE
| peRAG 2 | bel ES | {oseas 4] | — | |||
| = | AG | 05] | OTRAQ 23. | ROT | ||
| Beryl, | oe S22 | OSEAIO te | ||||
| 1 | Ee | BBRAL 281 45, | 17 BROT. | LoTRatl 19} | ||
| J8_— | erpiRecowaL | Bee | m1 | Back vid | ||
| T4LS32 |, BUFFER. | 22 Bilge | -Zeala 2] | as | x | ||
| = | P | we Oe | iS Giz. | Ack VID. | ||
| iran | fey Jeo Lit | se taisisr “4 | ||||
| BENE | ; | el2de13. | 25K ya 2 BACK VD 2, | |||
| E10-11 | BACKEROUND | es | le | |||
| - | Meta | ChaRaeTeR | Ce | Creeres | ||
| ey | 8 | ci | FI5 | et sires | ||
| BACKeROUND | RAM | ——- | ||||
| Segre | REEL] | “BOTRWR/ ornate | ~ | | |||
| eas 9| | = | wes. | 2 ors | SHON J4 | osama 3: | wee |
, x se
| THEE 1g | TERR | ser], | frame | af arr |
fare at
| ; | We 2] Prgister Yop eee | Tikae | pro7|"" Lio | oxeats 370, | |
| a | aaa Jaz 2 MOK yg 9 BERT | peor | vast @ | |
| 5 | rege | oe | 2h cux, | somwe It |
> TEA K1,K2,K3, ses 1}
| ‘degect Rom | rea | seBw. | lan | oon, |
aobRess eArenes
7 LOGIC BOARD ASSY. (A1), SCHEMATIC DIAGRAM, SHEET 3 OF 3 21 22 23
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
| POWER SUPPLY ASSY. {A3), COMPONENT LOCATION | a | ae | a | —S—_—_—_— | FF | sens = sr | ses | eee | — | a |
| 2N5879 | HS, TO=3 | ¢-t5¥ OC (SOURCE) | S16 | a |
100n H
| tan [RI [RIS | IN4734A | }— + 515 | ||
| 2000 | cls | ser I | H | 5 |
cn
| 36 | z | TIP31B | w25w | lol? | MCR68-! | 3.8y, 5% | T | id |
| -nvoct | slut | wl | t | |||||
| vif* | loout | - | i | Ri | rT | |||
| 33 A | 4b C32 | 16V | 50V | 470n | H | = | ||
| bas | esl | Ww | | cee |
hota 200 H
| pas. | rv} | TL431 | + | = | esw | MVS752 yw | jo s=E>»> |
| cn | vet | + | TO-92 | . | ah | ; | = |
| a | Mal | R18 | | __ancS. |
a5 ‘
| ce | RIG | i | KEY, | 14 |
seen] Lsg
| + | 2 | ——> | ||||
| cr a+ | e2t | -—-+}+>7 | ||||
| £ | ci 4h | HS. To-3 | * | i | ||
| Ae | R22 | Ts | ||||
| $3 | 22 | sk | N3 O55, | C23 | Lt | ‘55 |
. + T
| 2: | +4evoc] | 7” | aus | Ley | |
| Ze | c22 | ' | |||
| ake t | [2200uF | Sov | i | ||
| som s | 024 | lal | | ira | ||
| 82 3 | Pe | 28, | IN53633, | Ts | r |
| Ce | ex R21 | p26 | t+-—> 2 | ||
| Le | Tere | 30V, 5% | i | ||
| oE | 5w | is, | |||
| F3t eat | - | Sa | an ii |
“\y IN
| Fal | 38. | pos | - |
IASB. P3
| D4t | 032 | 1 | —— | ae ’ |
| 1N4004 | 68 | +30V DC (SOURCE) | 6 | |
| al | 4N4004 | + | +19.3V Lm | > |
| (ay | L | +12v Dc (SOURCE) | ||
| p42 | R31 | 470uf | 2uf | i>4 |
| 1N4004 | 034 | med | 16V | f |
| B33 7500. | 38v 7 | uy | ins |
c3r in
| + | L | i | ||
| 035 | 7 | : | i | 4 |
POWER SUPPLY ASSY. (A3), PARTS LIST ave7e? i
| 44 IN4004 | KEY, | 2 |
REFERENCE DESCRIPTION PARTNO. REFERENCE DESCRIPTION PARTNO. '
| Power Supply Asx. | MA-430 | 2 | Connector, 1 PN | 0-531 | imse0 | H | ||||
| cn, C32, C42 | Capacitor, 01 mid. SOV | xO-229 | Pa | Connector, 7 PIN, | 0-526 | AUDIO GND | -19.3v DC | IN} MLP- | ~12v Dc (souRCE) | _! |
| cara | Capacitor, 1OOUF, 16V | 30-235 | Ps | Connector, 6 PIN | x0372 | +> 3 | ||||
| 3.023 | Capector O1UF. 100V | xOos | on | Stansston PNP, 2NS879 | xO323 | 7500 | Ter | Tot | ual | t |
| Cis, C33,c43—_Capacitor,02UF. 16V | x0-205 | az | Transistor. NPN, TP3I8 | X06! | i | 38V | (7912) | ! | ||
| C21. C22 | Capactor, 22000. 75 | xO32 | a2 | Transistor, NPN, 2N3055 | x0-301 | R4 | - | ' | ||
| C31 Cat | Capacitor, 470UF, 35V | XO-284 | Rit | Resistor, 470 OHM, 5% YW | xO-55 | cal | GND | t | ||
| on, 025 | RI | Resistor, 100 OFM, 5% 1W | x0.137 | = | t | |||||
| 035, D#3 | Diode, Light Emitting MV-5752_XO-270 | RIB, RIG | Resistor, 12 OHM, 5% | xo-138 | 043 | aw | NOTE: | t | ||
| pz | Diode, Zener, 5 6V, 556 IW, | 0-255 | 5 | Resistor, 200 OHM, S% uw | XO143 | Mv5752 | ALL RESISTORS ARE +5% | Hl | ||
| INS734A | RIG | Resistor, 180 OHM 5% YW | —-XO-2E | ' | ||||||
| 2-024 | Diode, INS401 | x0-263 | RI? | Resistor 100 OHM, 5% 4W = XO-28 | + | ! | ||||
| 026 | Diode, Zener, 30V, 5% SW, | x0-273 | a | Resistor, 20 OHM 596 YW | xO-29 | mE oOV Oe | H | |||
| 1N53638 | R21, R22 | Resistor, L8KOHM, 5% 2W- | XO-135 | — >i | ||||||
| 031-034, 036 | R23 | Resistor, 200 OHM, 5% SW | XO-133 | |||||||
| DSI D4Z,.083 | Diode, IN4004 | x0.254 | 31 Rat | Resistor 750 OHM, 556 1W/ | x0:1%6 | |||||
| fi | Fuse, 6% AMP SLO-810 | ea | scett | Siicon Controle Rectifier | xOr31 | |||||
| Fi | Fuse, 2 AMP SLO-BLO | a7 | ut | Diode, Programmable Zener T431_XO-272 | eee | —_ | —_— | |||
| 31, 632 | Fuse, “AMP SLO-BL0 | a5 | U3i | Volage Rego 12M 307 30473 | ||||||
| Fai | Fuse, AMP SLO-BLO | Eve | ust | Voltage | Regulator I2V. | LM 320 | X0-130 | |||
| m | Comer 4 PN | fs87 | val | xenon 100 nM | xO | POWER SUPPLY ASSY. (A3), SCHEMATIC DIAGRAM |
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
SOUND/SPEECH ASSY. (A6), COMPONENT LOCATION
sisroses ma
8-20887. T
[=
REFERENCE
cL 4, CB C15, C16,C19 20,21, C23 C25, C26 €28-C30, C33 42, C44 carc32 ar 3, C38-c41 C4, C24
C45, C46
i cra 1.03 a2 RI, RA, RS RIL RIZ R2, RB R6, RIB ROA, R7, R23-R30 RB, RBA, RIG R68 R9 R10 SOUND/SPEECH ASSY. (A6), PARTS LIST
DESCRIPTION
Sound/Speech Assembly Capacitor, 0.1UF, 25V
Capacitor, .047UF, 25V Capacitor, 4.7UF, 35V Capacitor, 47UF, SOV Capacitor. 100PF Capacitor, 300PF Capacitor, 1UF, 50V_ Capacitor, 470UF, 35V Capacitor, 33PF Capacitor, .01 UF, 100 Diode, IN4 148 Diode, Zener, 1NS225B Transistor, NPN, 2N2222A Transistor, PNP, 2N2907A Resistor, 5.6K ohm, 5%, YAW
Resistor, 2K ohm, 5%, JW Potentiometer, 10K Resistor, 10K ohm, 59%, YAW Resistor, 1K ohm, 5%, JW Resistor, L8K ohm, 5%, YAW Resistor, 22K ob, $%, iW Resistor, 15K obm, 5%, YW PART NUMBER
MA216 XO-248
XO-222 x0-291 XO-2 10 XO-223 XO-283 XO-217 X0-284 XO-277 0-202 xO-261 XO-269 X0-320 XO-321 XO-19
XO-8 XO-108 XO-18 xO x0-37 xO27 xO-20 REFERENCE DESCRIPTION
RIS, R16 Potentiometer, 10K ohm R18, R21 Resistor, 100K ohm, 5%, AW R22 Resistor, 2K ohm, 5%, AW R31 Resistor, 68K ohm, 5%, JW RPI, RPZ Resistor, Dip sB1 Switch, Dip swt Switch, Momentary Pushbutton ul Ic, 7414 U2 IC, SN741S74N U3 CPU, R6502- 13 ut IC, SN74LS 138N US, U6 EPROM, 2716 U7-U9, UI, UIB IC, SN74LS75 ul0 IC, SN74LS02N ui IC, SN7407N uns IC, Inverter, SN74LSO5N ule ‘Voice Chip, SCO1 UIs RRIOT, R6532-18 ute IC, SN74LSO4N vuI7 IC, SN74LS30N U19, 20 Converter, PMI, 1408A-6P 21, U22 IC, UM74 ICP U23 IC, Uvi379s u24 IC, Dual Comparitor, LM 193 25 Inverter, 7404 7] Crystal, 3.57954SMHZ Socket 22 Pin Dip Socket 24 Pin (2) Socket 40 Pin (2), PART NUMBER
XO-109 xO-45 XO-14 x0-189 XO-168 0-505 XO-515 X0-397 XO0-434 XO-360 X0-437 PRB, XO-3%4 x0-428 xo-384 XO-411 xO468 X0-361 X04 18 x0-432 x04 16 X0-393 XO-395 X0-396 x0-402 XO-456 x0-467 x0-529 X0-530 #/0 AGPI ‘ap S1 20 uie-13, s¢ 10 u1e-1 | {ip $80 vies)
- 3, LMla3 RESO2 #1 Lamp DRIVER | CPU
INTERFACE peg
JUMPER CONNECTIONS E16-E17, Maz
- LLEGEND WITHIN GATES. INDICATES SCHMITT TRIGGER, S.WITH THE EXCEPTION OF EL,EZ,E3 AND E1G,E17, E183 SOLID’ JUMPERS USE6 with ZING PROMS. DASHED JUMPERS USED WITH 2732 PROMS. , Ba
ng
Rw Ele-€18, 2Myz, fe Ee C17 vida 221 612 NMI fo RS
ALR sam 63
ABIZ. ABIS TING ADDRESS BUS
I> u15-36
Jur J, 65
DATA BUS 68 O4UF tv ey
oR
23 ¢ 561-8
FROM TCT. RPL-44 BFR
P/O AGPI 7 +5V
Tiev r Te a
+Lese “REG. TS vat Aso — 25} Lar Ed} ANALOG 2a) VE RTER,
Sense Bv,i0% AMR 6|
ce SSS he PREP
SPARES +5v 4v
628 629 Oive wie | Poker ro F * r41804 |t4 &
| Bag | md | 13,84 | Aspire |
| BM | pat | ul | se sr | |
Aas + |] se, ase paz PO oc} . . al | [se
| a | eee | hi | stu | ||
| ioe | ws | At | i | ~FeTT | Tso |
2 | .
| DIGITAL, | DIGITAL | AS | PAS |
To to
| ANALOG | ANALOG, | Es |
| conveRrER| | cOWERTER | Zi |
Fa 23) a
-hy —s
VOLUME, iS Cat :
K .0470F Hislals [6
Ne
| Rie | 032 | BE | | | <rUF |
0,8 auor0 OUT Pt vows a vas am AMPA ~ 7407 Wa R LEVEL SHIFT 70u3-6 «——*4]
SOUND/SPEECH ASSY. (A6), SCHEMATIC DIAGRAM
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
XI. PARTS INFORMATION
TABLE OF CONTENTS
PAGE
SPEAKER/MARQUEE ASSY. ....
ILLUMINATION ASSY. ...........----..05+ 34
CONTROL PANEL ASSY. ...............+.- 35
SERVICE PANEL ASSY....................- 36
BOTTOM PANEL ASSY. ................... 37
CABINET PARTS..............-.. 0000s eens 38
CABINET PARTS...............6..002 000s 39
»{
2 3
ITEM ~—sC«DESCRIPTION
illumination Assy. Starter Ballast (60 HZ) Lamp. Fluorescent Cable Assy. Speaker Assy. Cable Assy. Speaker
Speaker Gritl
Marquee, Lexan (Screen) Svanewswna » PARTS INFORMATION
SPEAKER/MARQUEE ASSY. AND ILLUMINATION ASSY.
4 5
PART NO.
MA-376 EL-69 EL-70 lA4 MA-364 MA-377 MA-318 EL-83 B-20931 DE-3
XI. PARTS INFORMATION
CONTROL PANEL ASSY.
2,3 4
TEM ~—— DESCRIPTION PART NO.
| 1 | Control Panel Assy. | MA-374 |
| 2. | Short Button {2} | A-21970 |
| 3. | Button Holder and Switch (2) | A-21971 |
| 4 | Joystick | C-22458 |
| 5 | Cable Assy, | MA-382 |
| 6. | Lexan Overlay | DE+ |
XI. PARTS INFORMATION
SERVICE PANEL ASSY.
ITEM ~—— DESCRIPTION.
2. 3. A 5. 6. Service Panel Assy. Cable Assy. ‘Switch (Push Button) Switch (Toggle) Volume Controt Cain Meter PART NO.
MA-300 MA-316 EL-57 EL-85, XO-104 EL-84
XI. PARTS INFORMATION
BOTTOM PANEL ASSY.
EGRIS wenguawn- DESCRIPTION
Bottom Panel Assy. Transformer Capacitor, 50, OOOUF, 25V Resistor, 200 OHM, 5%, 2W Fuse, 3 AMP, SLO-BLO Cable Assy. (Secondary) Fuse, 1 AMP, SLO-BLO- Fuse, 10 AMP
Bridge Rectifier (2
Fuse, 2 AMP, SLO-BLO- Fuse, 4 AMP, SLO-BLO. Service Outlet une Filter
Cable Assy. (Primary)
PART NO.
MA-375 C-21931 xO-141 XO-142 EL-9 MA-314 ELS EL-23 EL-42 EL-7 EL-33 A18133 EL-50, MA-363
CABINET PARTS
NOT SHOWN
| ITEM | DESCRIPTION | PART NO. | ITEM | ~—s—éD’iESCRIPTION | PART NO. |
| 1 | Vent Chanrel (1) | D-21754 | "1 | Shield, Bottom | C-22633 |
| 2 | ‘On-Off Switch | EL-56 | 2. | Clip Bracket, Shield | B-22631 |
| 3. | Switch Plate | A-223% | 13, | Line Cord | B+15357 |
| 4. | Cable Assy. Master Electronics | ~MA-397 | 14. | Cover Plate, Line Cord | A-21955 |
| 5. | Interconnect Cable | MA-398 | 15. | Cable Assy. High Voltage | MA-360 |
| 6. | Back Door | D-21896 | 16. | Knocker Assy. | MA-384 |
7 Master Electronic Board MA394 7, Fuse, 1 AMP, SLO-BLO EL
8. Rear Door Lock MH-0 18. Interlock Switch EL-66
| 9. | Anchor Piate, Lock | MH-1 | 19. | Cover, Interlock Switch | A-21888 |
| 1o. | Shield, Top | €-22632 | 38 |
ANaWN- DESCRIPTION
Top Glass (Screened) Monitor Filter Glass Monitor Mask Monitor Cable Assy., Front Door Interlock Switch
XI. PARTS INFORMATION
CABINET PARTS
PART NO.
SGI D-22465 D-22463 C-22462 MA-365, EL46
ITEM DESCRIPTION
7. 8. 9.
10. Cover, Interlock Switch 3” Leg Adjuster (2) Decal (Right) Decal (Left) Lexan Overlay [Screen] PART NO.
A-21888 MH-21 DE4 DE4 DE-2
SERVICE NOTES
wells-Gardner elecTRONICS Wen SConPoRATION
19” IN LINE COLOR MONITORS
MODELS
19K 4901 19K 4906
19K4951 19K4956
wells-Gardner electronics
CORPORATION 2701 NORTH KILDARE AVENUE CHICAGO, ILLINOIS 60639
WARNINGS
- Power Up Warning— An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing or testing is performed since the chassis and the heat sink are directly connected to one side of the AC line which could present a shock hazard. Before servicing is performed, read all the precautions labelled on the CAT and chassis.
- [X-RAY RADIATION WARNING NOTICE |
- High Voltage— This monitor contains HIGH VOLTAGES derived from power supplies capable of delivering LETHAL quantities of energy. Do not attempt to service until all precautions necessary for working on HIGH VOLTAGE equipment have been observed.
- CRT Handling— Care must be taken not to bump or scratch the picture tube as this may cause the picture tube to implode resulting in personal injury. Shatter proof goggles must be worn when handling the CRT. High voltage must be completely discharged before handling. Do not handle the CRT by the neck.
- | PRODUCT SAFETY NOTICE
AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.
For replacement purposes, use the same type or specified type of wire and cable, assuring the positioning of the wires is followed (especially for H.V. and power supply circuits), Use of alternative wiring or positioning could result in damage to the monitor or in a shock or fire hazard.
PERFORMANCE AND OPERATING DATA
- Apply a suitable power source to the monitor through an isolation transformer.
- Apply a suitable signal source to the monitor PCB by means of P201 and P202
- Set Up Controls. Ali controls are preset at the factory. but may be adjusted to suit program material, 1.0 Supply Voltage 108 VAC-132 VAC. Frequency 50 Hz-60 Hz
3.0 Service Set-Up Controls MAIN PC BOARD 3.8 Horizontal Width Coil, L352 3.9 Black Level Control, VR201 3.1 Vertical Hold Controt, VR301 ; . ie 3.2. Vertical Size Control, VR303 aia tread i a 3.3 Horizontal Hold Control, VR351 3.4 Vertical Raster Position Adjustment NECK PC BOARD Jumper (3 positions) 3.11 Video Drive Controls, Red VR401 3.5 Horizontal Raster Position Adjustment Green VR402 Jumper (3 positions) 3.12 CRT Cut Off Controls, Red VR403 3.6 Screen Control (Part of H.V. Unit, T352) Green VR404 3.7 Focus Control (Part of H.V. Unit, T352) Blue VR405
SERVICE INSTRUCTIONS
1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level {the black portion of the picture just extinguished). 2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.
- 3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. 4.0 FOCUS Adjust the Focus control, tocated on the HV unit(T352), for maximum over-all definition and fine picture detail. 5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.
6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. "7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”. 8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R" or "L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.
«REO 19° RIVE GRN DRIVE REO CUTOFF GRN CUTOFF’ BLU CUTOFF
NEG H SYNC
BLU crn HORIZ HOLO
RED BLK LEVEL
HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT
FIGURE 1
INSTALLATION AND SERVICE INSTRUCTIONS
1.0 DEGAUSSING The monitor is equipped with an automatic degaussing circuit. However, if the CRT shadow mask has become excessively magnetized, it may be necessary to degauss it with a manual coil. Do not switch the coil OFF while the raster shows any effect from the coil.
2.0 COLOR PURITY AND VERTICAL CENTERING ADJUSTMENT 2.1. For best results, it is recommended that the purity adjustment be made in the final monitor location. If the monitor will be moved, perform this adjustment with it facing west or east. The monitor must have been operating 15 minutes prior to this procedure. 2.2 Set the converger assembly on the CRT neck with the center line (of the Purity Adjustment Magnet) over the gap between grids no. 3 & 4. (See Figures 2 & 6) 2.3. Make certain that the magnetic ring-pairs are in their correct positions before starting procedure. This produces a zero-correction state and helps facilitate adjustments. 2.4 Vertical raster position adjustment jumper must be in position “C" (center). 2.5 Remove the R-G-B signal from the monitor. 2.6 Turn the Green Cut off Control (VR404) on the Neck Board fully CW. (See Fig. 3) 2.7 Turn the Red and Blue Cut off Controls (VR403 & VR405) fully CCW. 2.8 Pull the Deflection Yoke backward so that the Green belt will appear. (See Fig. 4) 2.9 Decrease the horizontal width of the raster. if necessary, in order to be able to see the right and left edges of the raster. 2.10 Move the two Purity Magnets with respect to each other in order to center the raster on the screen and the Green belt on the raster horizontally 2.11 Push the Deflection Yoke forward gradually and fix it at the place where the Green screen becomes uniform throughout. 2.12 Turn the Cut off and Drive Controls and confirm that each color is uniform. 2.13 If the color is not uniform, re-adjust it moving the Purity Magnets slightly. 2.14 Decrease the vertical size of the raster, if necessary, such that the top and bottom raster edges can be seen. “GaP (GRIDS NO. ‘3AND 4)
PURITY ADJ. RED/BLUE ADy. RED/ BLUE ON GREEN ADy.
REO/BLUE REO/BLUE ON GREEN 2 o'clock 10 o'cLock
REAR CONCENTRIC VIEW CONVERGER ASSY. SHOWN IN ZERO CORRECTION POSITION
PURITY PURITY
9 O'CLOCK 3 O'CLOCK INDIVIDUAL
TAB ROTATION FIGURE 2
Rai2 Rant R410
TP47R
VR4Ot
vRao2 GREEN ORIVE
| vraos—7 | vraoa | “vr4o3 |
| BLUE | GREEN | REO |
| CUTOFF | CUTOFF | CUTOFF |
FIGURE 3
NECK BOARD
WEDGE if GREEN BELT
FIGURE 4
2.15 Rotate the Purity Magnets as a pair (without changing the angle of one magnet relative to the other) in order to center the raster on the screen vertically. 2.16 Readjust the raster to the desired vertical size. 2.17 Turn all three cut off controls fully counterclockwise (CCW). Slowly turn up (CW) the Red cutoff control untila Red raster is just barely visible. 2.18 Slowly turn up the Green and Blue cutoff controls such that their associated colors, mixing with the Red, results in a White or Gray raster. 2.18 Confirm that the white or throughout the screen. 2.20 Insert a wedge temporarily as shown in Fig. 4 and adjust the angle of the Deflection Yoke. 3.0 STATIC CONVERGENCE ADJUSTMENT
4Pole Magnets and 6-Pole Magnets are for static convergence.
3.1 Across hatch signal should be connected to the monitor. 3.2 A pair of 4-Poie Convergence Magnets is provided and adjusted to converge the blue and red beams. (See Fig. 6) When the Pole opens to the left and right 45° symmetrically, the magnetic field maximizes. Red and blue beams move to the left and right.(See Fig. 5) Variation of the angle between the tabs adjusts the convergence of red and blue vertical lines. 3.3. When both 4-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of the red and blue horizontal tines is adjusted. 3.4 A pair of 6-Pole Convergence Magnets is also provided and adjusted to converge the magenta (red + blue) to green beams. (See Fig. 6). When the Pole opens to the left and right 30° symmetrically, the magnetic field is maximized. Red and blue beams both move to the left and right (See Fig. 5). Variation of the opening angle adjusts the convergence of magenta to green vertical lines. 3.5 When both 6-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of magenta to green horizontal lines is adjusted.
FIGURE 6 GREEN GUN IS THE CENTER GUN. CONVERGE THE RED AND BLUE. THEN CONVERGE RED AND BLUE ON GREEN.
gray coior is uniform | VERTICAL 4-POLE, CONVERGENCE |MAGNETS BLUE 6 RED
3.2
\__ SLIDE MAGNETIC RING TABS TOWARD OR AWAY FROM EACH OTHER
4-POLE HORIZONTAL CONVERGENCE |MAGNETS
BLUE 6 RED [owe
= REO
ROTATE BOTH MAGNETIC RINGS TOGETHER
VERTICAL 6-POLE i >) CONVERGENCE |MAGNETS ( ' “ON GREEN GRN | iREO/BLU
3.4 :
SLIDE MAGNETIC RING TABS TOWARD OR AWAY FROM EACH OTHER, HORIZONTAL | 6-POLE a, CONVERGENCE [MAGNETS BLUE & RED ON GREEN
ROTATE BOTH MAGNETIC RINGS TOGETHER
REPEAT 3.2 @ 3.3 IF ALL LINES ARE NOT CONVERGED AT CENTER 5827 FIGURE 5
ANODE CONTACT
Log PoLe CONVERGENCE MAGNETS ] PONVEReENE! 4 POLE CONVERGENCE MAGNETS MAGNET ASS ~— PURITY CENTERING MAGNETS { \ —~ DEFLECTION YOKE
RUBBER WEDGES
4.0 PRECISE ADJUSTMENT OF DYNAMIC CONVERGENCE (See Fig. 7, 8 and 9)
4.2
4.3 Feed a cross hatch signal to the monitor. Insert a wedge temporarily and fix the Deflection Yoke so as to obtain the best circumference convergence (See Fig. 8 and 9)
2)
3)
4)
5)
6) Tilting the angle of the yoke up and down adjusts the crossover of both vertical and horizontal red and blue lines. See Fig. 8 (a) and (b). Tilting the angle of the yoke sideways adjusts the parallel convergence of both horizontal and vertical lines at the edges of the screen. See Fig. 9 (a) and (b). Use three rubber wedges (tapered rubber wedges are used for a purpose). The position of each rubber wedge is shown in Fig. 7. Do NOT force the permanent wedges in. They are to be inserted until they just make contact with the yoke—after the yoke has been positioned. Fix the three permanent rubber wedges with chloroprene rubber adhesive. After the adhesive has dried enough to hold the wedges in place, carefully remove the temporarily installed wedge.
UPPER \
RGB UNDER BGR
vow TEMPORARILY INSTALLED WEDGE
RUBBER WEDGE
YOKE
FIGURE 7
UPPER
cRT
BGR UNDER
(b) o oon
crt screen '°) wert RUBBER WEDGE CRT SCREEN INSERT RUBBER WEDGE
FROM UPPER SIDE FROM LOWER SIDE
, \ BR Yr Ll FIGURE 8
t 4 -
(b) CRT SCREEN INSERT RUBBER WEDGE CRT SCREEN INSERT RUBBER WEDGE
FROM LEFT SIDE FROM LOWER SIDE FIGURE 9
5.0 WHITE BALANCE
5.1
5.2 5.3
5.4
5.5
5.6
5.7 Reter to Fig. 2 and do the following in subdued light. Ground the R/G/B inputs. Set the R/G drive controls to their mechanical centers. Set the screen and R/G/B cutoff controls to minimum (fully CCW). Connect a jumper wire between TP301 and TP302 (iocated on the MAIN PCB) Slowly turn up (CW) the screen control until the first colored line becomes just barely visible. That coler which has just appeared is referred to as the “lead” color. Do NOT turn its associated cutoff control—it must remain fully CCW. Connect a DC oscilloscope to the collector of the lead color's output transistor (Q401, Q402, or Q403) on the Neck PCB at TP47Rh, TP47G, or TP47B. 5.8
5.9
5.10
5.11 §.12 Adjust the black level control (VR201) to obtain the waveform shown in Fig. 10. Readjust the screen control such that the colored line is just barely visible. Slowly turn up the two remaining cutoff controls such that their associated colors, mixing with the lead color, results in a white or gray line. Remove the jumper wire. Adjust the Black Level Control for a dim raster. Touch up the two trailing cutoff controls (NOT the lead cutoff control) for best gray uniformity. Adjust the Black Level Control for a bright rasier. Adjust the R/G drive controls, if necessary for best neutral white. Repeat steps 5.12 and 5.13 until good tracking of white balance is achieved.
BLANKING PULSES
FIGURE 10 140V
O-voc
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A* on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Ref. No. | Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| Ra01 | 203X8500-645 | 1K Ohm, 5%, 1!4W Carbon | R369 | 203X5602-329 | 680K Ohm, 5%, 1/2W Comp. | |
| R202 | 203x6500-523, | 30 Ohm, 5%, 1/4W Carbon | R370 | 203X€501-002 | 33K Ohm, 5%, 1/4W Carbon | |
| R203 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R971 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide | |
| R204 | 203X6700-227 | 100 Ohm, 5%, 1/2W Carbon | R972 | 203X9101-119 | 12K Ohm, 5%, 1W Metal Oxide | |
| R205 | 203X6700-424 | 270 Ohm, 5%, 1/2W Carbon | R375 | 203X8700-763 | 6.8K Ohm, 5%, V/2W Carbon | |
| R208 | 203X8500-540 | 390 Ohm, 5%, 1/4W Carbon | RI76 | 203x9104-404 | 270 Ohm, 5%, 2W Metal Oxide | |
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203X6500-447 | 180 Ohm, 5%, 1/4W Carbon | |
| R208 | 203x6500-540 | 380 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R209 | 340X2201-834 | 200 Ohm, 5%, 1/4W Carbon | R79 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R210 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R380 | 203X6500-865 | 8.2K Onm, 5%, VW Carbon | |
| Ratt | 340X2201-934 | 200 Ohm, 5%, 1!4W Carbon | R381 | 203x6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | |
| R214 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R383 | 203x9014-387 | 150 Ohm, 5%, 1W Metal Oxide | |
| R215, | 203x6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R216 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204X 1700-535 | 150 Ohm, 5%, 1SW Metal Oxide | |
| R217 | 203x6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014-267 | 47 Ohm, 5%, 1W Metal Oxide | |
| R218 | 203x6500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon | |
| R219 | 203X6501-126 | 100K Ohm, 5%, 14W Carbon | R506 | 203X9104-105 | 15 Ohm, 5%, 2W Metal Oxide | |
| R220 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R607 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | |
| R221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Garbon | DwROT | 204X1625-058 | 3.3 Onm, 5%, tow WW | |
| R222 | 203%6500-762 | 3.3 Onm, 5%, 1/4W Carbon | R704 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | |
| R224 | 203x6500-169, | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2 Carbon | |
| R225 | 203X6500-169 | 10 Ohm, 8%, 1/4W Carbon | R201 | 204x2070.072 | 2K Ohm-B Semi-Fixed | |
| R226 | 203X6500-169, | 10 Ohm, 5%, 1/4W Carbon | R301 | 204X2070-084 | 5K Ohm-B Semi-Fixed | |
| 227 | 203X6501-044 | 47K Ohm, 5%, 1/4W Carbon | R303 | 204X2070-055 | 500 Ohmi-B Semi-Fixed | |
| R228 | 203X6500-645 | 1K Ohm, 5%, V/4W Carbon | Raat | 204x2070-072 | 2K Ohm-B Semi-Fixed | |
| R229 | 203X6700-421 | 270 Ohm, 5%, 1i2W Carbon | R352 | 204X2070-072 | 2K Ohm-B Semi-Fixed | |
| R230 | 203X6500-863 | B.2K Ohm, 5%, 1/2W Comp. | ||||
| R231 | 203X6500863 | 8.2K Ohm, 5%, | 1/2W Comp. | |||
| 232 | 203X6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R233 | 203X6500-468 | 180 Ohm, 5%, 1/4W Carbon | ||||
| F234 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | CAPACITORS | |||
| R235 | 340x2820-934 | 82 Ohm, 5%, 1/4W Carbon | C201 | 203X0014-088. | 1000 uF, 16V, Electrolytic | |
| R236 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | C202 | 202X7200-084 | 330 pF, 500V, Ceramic | |
| 301 | 203X6500-508 | 270 Ohm,5% , 1/4W Carbon | C203 | 202X7200.043 | 220 pF, 500V, Ceramic | |
| R302 | 203X6500-863 | 8.2K Chm, 5%, 1/4W Carbon | 204 | 202X7200.043, | 220 pF, 800V, Ceramic | |
| R303 | 203X6800-863 | 8.2K Ohm, 5%, 14W Carbon | C205 | 203X0014-076 | 470 uF, 16V, Electrolytic | |
| R304 | 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | 206 | 203X1810-149 | 0.1 uF, 125V Mylar | |
| R305 | 203x6500842, | 6.8K Ohm, 5%, 1/4W Carbon | C207 | 349X2232-109 | (022 uF, 100V Mylar | |
| F306 | 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | C301 | 203X0014-065 | 390 uF, 50V Electrolytic | |
| R307 | 203x6500-825, | 5.6K Chm, 5%, 1/4W Carbon | C302 | 203X1600-563 | 0.033 UF, 50V Mylar | |
| R309 | 203X6500-965 | 22K Ohm, 5%, 1/4W Carbon | C303 | 203X0629-037 | 3.3 uF, SOV Electroiytic | |
| F310 | 203X6500-988 | 39K Ohm, 5%, 1/4\ Carbon | 6304 | 203X 1600-266 | 0.068 pF, SOV Mylar | |
| R311 | 203x6500-762, | 3.3K Ohm, | 5%, 1/4W Carbon | C306 | 203X0412-012 | 2.2 uF. 16V Tantal |
| 7312 | 203X9014-741 | 4.7K Ohm, | 5%, 1/4W Carbon | 307 | 203x 1600-634 | 0.033 UF, SOV Mylar |
| R313 | 204 1450-537 | 1K Ohm, 5%, 5W Carbon | C308 | 203X0025-174 | 3.3 uF, 50V Electrolytic | |
| R314 | 203X6500-481 | 220 Ohm, 5%, 1/AW Carbon | C309 | 203x1207-100 | 0.068 UF, 100V PP | |
| R315 | 203X6500-169 | 19 Ohm, 5%, 1/4W Carbon | 310 | 203X0629-061 | 10 uF, 100V Electrolytic | |
| R316 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | cant | 203X0041-025 | 10 uF, 160V Electrolytic | |
| Rat? | 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | C312 | 202X7050.248 | 4000 pF, 500V Ceramic | |
| R318 | 203X6500-540 | 390 Ohm, 5%. 1/4W Carbon | C313 | 203X0040-052 | 47 uF, 160V Electrolytic | |
| R319 | 203X6500-645, | 1k Ohm, 5%, 1/4W Carbon | C314 | 203X1201-265 | 0.033 uF, 200V PP | |
| R320 | 203x6501-002 | 33K Ohm, 5%, 1/4W Carbon | 0315 | 203x0629-023 | 1 uF, 50V Electrolytic | |
| R921 | 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | C351 | 203x0629-023, | 1 UF, 50V Electrolytic | |
| Ra22 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | C352 | 203X0619-045 | 47 UF, 25V Electrolytic | |
| R951 | 203X8500-886 | 10K Onm, 5%, 4 Carbon | C353 | 203X1190-015 | 0.0082 pF, SOV Mylar-PP | |
| F352 | 203X6800-785 | 3.9K Ohm, 5%, 1i4W Carbon | C354 | 203X0619.045 | 47 uF, 25V Electrolytic | |
| F353 | 203X6501-088 | 68K Ohm, 5%, 1/4W Carbon | C355 | 203X1600-366 | 0.0068 pF, 50V Mylar | |
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483, | 0.01 uF, 500V Ceramic | |
| FO55 | 203X9205-143 | 6.8K Ohm, 5%, 3W Metal Oxide | 0359 | 202X8065-606 | 100 pF, 500V Ceramic | |
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366 | 0.0033 pF, 500V Ceramic | |
| R360 | 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| R361 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| R362 | 203X9014-645 | 1.8K Ohm, 5%, 1W Metal Oxide | AxC363 | 203X1270-911 | 8700 pF, 1.5 KV PP | |
| RIGS | 204X 1527-751 | 3.9K Ohm, 5%. 7W Metal Oxide | C365 | 203X1201-265 | 0.33 uF, 200V PP | |
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/AW Carbon | C366 | 203xX0019-026 | 22 uF, 25V Electrolytic | |
| R365 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8065-162 | 6 pF, 500V Ceramic | |
| R367 | 203x6500-886 | 10K Ohm, 5%, 1/4W Carbon | 368 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| R368 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | ca72 | 203X1207-125 | 0.1 uF, 100V PP |
P.C. BOARD LAYOUT
TOP VIEW
be Oem Gen ea " ‘]
a et ee = = cae INT. FACE: my eed ‘VERT. OUT “
Pwa-o8a BOTTOM VIEW
FIGURE 11 MAIN P.C. BOARD.
P.C. BOARD LAYOUT
TOP VIEW
BOTTOM VIEW
FIGURE 12 NECK PC. BOARD
MAIN BOARD (CONT)
| Ret. No. | Pert No. | Description | Ref. No. + | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 380 | 202X7200.087 | 470 uF, 500V Ceramic | 2206 | 200X3181-523 | Transistor (NPN) 28C1815GR |
| A.C501 | 203x 1810-149 | 0.1 uF, 125V Mylar | Q207 | 200x3181-523, | Transistor (NPN) 25C1815GR |
| 4 0502 | 202X7050-282 | 1500 pF, 500V Ceramic | 208 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| 4c503 | 202X7810-214 | 2200 pF, 125V Ceramic | 209 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| Ac50S | 202K7810-214 | 2200 pF, 125V Ceramic | 210 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| C505 | 203X0220.075 | 560 uF, 200V Electrolytic | Q301 | 200X3181-523 | Transistor (NPN) 28C1851GR |
| C506 | 203X0040-034 | 22 uF, 160V Electrolytic | Q302 | 200X3207-306 | Transistor (NPN) 28C20731-8GL2 |
| 0507 | 203X0041-057 | 47 uF, 160V Electrolytic | 2303 | 200X3207-306 | Transistor (NPN) 25C2073LBGL2 |
| 701 | 203X0019-092 | 4000 uF, 25V Electrolytic | Q351 | 200X3248-217 | Transistor (NPN) 25C24828K |
| 702 | 203X0634-061 | 10 uF, 100V Electrolytic | 352 | 200X4589-802 | Transisior (NPN) 2508888 |
| 703 | 202X7050-248 | 1000 pF, 500V Ceramic | aw eet | 200X2300-033 | IC HA11423, |
| Ic501 | 200X2600-183 | IC STR381 |
SEMICONDUCTORS
| 0203 | 201X2010-159 | Diode, 182076-27 | ||||
| D204 | 201X2010-159 | Diode, 1$2076-27 | TRANSFORMERS & COILS | |||
| 0205 | 201X2010-159 | Diode, 152076-27 | L351 | 201%47 10-134 | Coll, (RF Choke) | |
| 208 | 201X2010.159 | Diode, 18207627 | L352 | 201X5000-083 | Coil, Horiz. Size | |
| D207 | 201X2010-159 | Diode, 18207627 | £701 | 811X0004-007 | Colt, Adg. | . |
| D208 | 2012010158 | Diode, 18207627 | 351 | 202X1300-080 | Transformer, Hor. Drive | |
| 209 | 201X2010-159 | Bicde isonre a7 | AK T352 | 200X9720-301 | HV-Unit M11 | |
| 0301 | 201X2010-165 | Diode, S881 | ||||
| 302 | 201X2010-159 | Diode, 1$2076-27 | MISCELLANEOUS | |||
| D303 | 201X2010-159 | Diode, 1S2076-27 | AFS501 | 204X7120-073, | Fuse, 4 Amp. 125V | |
| D304 | 201X2120-009 | Diode, RH:IV | J402 | 206X5008-632 | Recep W Wire 3P-M-BG | |
| 0305 | 201%2120.009 | Diode. RH-IV | P201 | 204X9600-466 | Plug, PW 3P-J | |
| D306 | 201X2010-159 | Diode, 1S2076-27 | P202 | 204X9601-477 | Plug, PWB 6P-Q | |
| D501 | 201X3120-216 | Diode, RM-1AV | P401 | 204X9600-298 | Plug, PWB 4P-B | |
| 0502 | 201X3120-216 | Diode, RM-1AV | P501 | 204X9600.249 | Plug, PWB 2P-B | |
| 40503 | 201X3120-216 | Diode, RM-1AV | P60 | 204X9600-304 | Plug, PWB 4P-C | |
| D504 | 201X3120-216 | Diode, RM-1AV | TH501 | 201X0100-112 | Thermistor | |
| D505 | 201X3120-216 | Diode, RM-1AV | ||||
| D506 | 201X3120-216 | Diode, RM-1AV | ||||
| D701 | 201x2190.234 | Diode, RU-2V | FINAL ASSEMBLY PARTS | |||
| D702 | 201X2120-009 | Diode, RH-1V | A 88X0198-506 | 19VLTP22 Pix Tube | ||
| Q201 | 200x3181523 | Transistor (NPN) 2SC1815GR | 205X9800-158 | Lateral/Purity Assembly | ||
| Q202 | 200X3181-523 | Transistor (NPN) 2SC1815GR | AW 202X1111-201 | Yoke Deflection | ||
| 203 | 200X4056-260 | Transistor (PNP) 25A562.Y-TM | 204x9301-255 | CRT Socket | ||
| 0204 | 200X4056-260 | Transistor (PNP) 2SA562.Y-TM | 291X5004-262 | Automatic Degaussing Coil Unit | ||
| 0205 | 200X4056-260 | Transistor (PNP) 25A582-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| Rot | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | cao1 | 202X7050-269 | 4200 pF, S0O0V Ceramic | |
| R402 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C402 | 202X7050-248 | 1000 pF, 500V Ceramic | |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248 | 4000 pF, 500V Ceramic | |
| R404 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 1500 pF. 1.5KV Ceramic | |
| R405 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| R408 | 2oaxe00061 | 820 Onm, 5% 1/4W Carbon | ||||
| R407 | 203x6000-7: | 470 Ohm, 5% 1/4W Carbon | ||||
| ad | 203X6000-98 | 270 Ohm, 8% AW Carbon | SEMICONDUCTORS | |||
| Lies | 203x6000-661 | 820 | Ohm, 5% 1/4W Carbon | Qao1 | 200X3206-800 | Transistor (NPN) 28C2068LB |
| R410 | 209x9104-824 | 18K Ohm, 5% 2W M.O. Forming | Ga02 | 700%2206.800 | sraneetor (NPN) 26C2068LB | |
| ma | 203X9104-824 | 18K Ohm, 5% 2W M.O. Forming | 2403 | 200X3206-800 | Transistor (NPN) 2SC2068LB | |
| R412 | 203X9104-824 | 48K Ohm, 5% 2W M.O. Forming | ||||
| R413 | 203X6000-998, | 2.7K Ohm, 5% 1/2W Comp. | ||||
| Roig | 203X6000.998 | 2.7K Ohm, 5% 1/2W Comp. | ||||
| R415 | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | MISCELLANEOUS | |||
| Rate | 203X9105-154 | 2.2 Ohm, 5% 2W Metai Oxide | 401 | 206x5000:296 | REGEF WWiredP-e |
. 2 204X9600-254 Plug, PWB 3P-A
| RA19 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | bpp | 9. | |
| R420 | 203X€500-741 | 2.7K Ohm, 5% 1/4W Carbon | a | aoesoony est | Piva: Ein teD |
. P701 204X9601-020 BAPE
| R42 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon |
| R401 | 204x2115-014 | 500 Ohm, -B Semi-Fixed |
| vRao2 | 204X2115-014 | 500 Ohm, -B Semi |
| R403 | 204X21 15-006, | 5K Ohm, -B Semi-Fixed |
| R404 | 204X2115-006 | 5K Ohm. -B Semi-Fixed |
| R405 | 204X21 15-006 | 5K Ohm, -B Semi-Fixed |
TYPICAL DC VOLTAGES
TERMINAL COLLECTOR | BASE | EMITTER TRANSISTOR NO.
15.4 14.0 15.5
41.4
DO NOT MEASURE
1.C. 501 PIN NO. | VOLTAGE 1 163 2 130 3 0 4 132 1.C. 301 PIN NO. OMPNANRWN = VOLTAGE
Power Supply Voltage and Symbols symbol | voltage Op.
® 16V ing Circuit
Vert. Ose. Syne Blanking CRT Cut-Off
Horiz. Ose. Horz. Drive Horz. Output Vert. Output ry) 130V PROTECTION
@ 175 Video Output PARTS LIST.
Q351 COLLECTOR
| AVIDIV 200uSECIDIV | 20ViDIV 10USECI/DIV | O.5IDLV SMSECIDIV |
JP31,06 COUPLED 402-3 BOTTOM LIN!
| 2V/DIV 200MSECIDIV | SVIDIV 20uSECIDIV | OSIDIV 20u SECIDIV |
LC. 901, PIN 3 F LC. 301, PIN 15
usa
1VIDIV SMSECIDIV 1VIDIV 20u SEC/DIV 1VIDIV 10USECIDIV
p82 TP-31, AC COUPLED
20VIDIV SMSEC/DIV 1V/DIV 200uSEC/DIV
1.6. 201, PIN 13 NEGATIVE SIDE OF C303 F
AVDIV 200uSEC/DIV 1VOIV 2MSECIDIV 2VIDIV SMSECIDIV X-RAY RADIATION PRECAUTION:
THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION
FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE
EGAUSSING COIL 19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956
20: Boieigy/ce. Be se ie. vt ane % 18 vay id 2SC\815GR/¥ aes] =e a Bees i | Lr
36! OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. if the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.
9401 9 402, 0408, REO-OUT GREEN OUT _SLUE OUT 28C2068.8/L88K 2SC2068L8/LBEK 25C2068L.098K 2SCIEBVCLVE 28CIBISBvCLVC 2SCIBIABVC/CVE
(were)
ae arciacie naeryaaae
é 356. £380, S58 9352
| Q35i | J | 280869 | if | | |
| HoRoRIve | ? yee | eehone | | |
28C24828K ape iO™ | @SC2EIOBK
=a sync AMP vosc Hose 8" f HAUa23 y
pe a @
503 ~cs0a 22008. 725) 30g Se ges
0305 nour [HOR.CENTERING] H.V.UNIT, 7352
K4901D, K4906D, K49510 5833 K4956B
SERVICE NOTES
15 462 0.G.& Co.11-82 16 WGEC SERIES 194900 69x1197 190,
D. Gottlieb & Co. warrants to
‘tems listed in the following sch ig
machine will for the applicable periods set forth In the ‘schedule -omputed from the initial date of purchase from an authorized D. Gottlieb & Co. distributor, be free of defects in “materials and workmanship:
SCHEDULE
GAME ITEM WARRANTY PERIOD
Pinball All Electronic 90 days
Pinball-Video All. Electronic 90 days Gunes Circuit
Gad ‘Cage 90 days
Television 30 days Monitor 7 All Electroni 90 days Printed Circuit Boards Television 30 days Monitor
arranty does not apply to any parts dareagee In the course of natal ) Or
all D. Gottlieb & Co.be jiabiel apd oe I ‘other losses incurred e tion with the purchas' ‘operation f D. Gottlieb & Co. machines or components thereof. The leg teste card with each D. Gottlieb : & Co. factory-wired machine | must | be fillec ain Warranty to be effective. ie Limited | Warranty applies only to machines so. registered,
THIS LIMITED | /ARRANTY 'S IN LIEU OF ANY INCLUDING ANY IMPLIED \ CHANTABI OR FITNESS, AND OF ANY OTHER OBLIGATION ON THE PART OF THE SELLER AND AMUSEMENT GAMES D. GOTTLIEB & CO.
Gottlieb
AMUSEMENT GAMES
165 W Lake Street Northlake. IL 60164 (312)562+7400 Telex 72+8463