CATHODE RAY TOMES

Super Masters

Super Masters (SEGA Enterprises, LTD., 1989) · Manual · 16 pages · 16 sections · original scan

Page 1

OWNER’S MANUAL

Page 2
  • Super Masters

TABLE OF CONTENTS

Introduction to the Owner’s Manual. . Handling Precautions . Prevention of Counterfeiting and Conversion . Precautions Conceming the Place of Installation . Disk Installation Name of Parts . Adjustment of the Service Switcl . Servicing the Power Supply Unit and Fuse . P.C. Board Assembly . Servicing the Floppy Disk.......... . Drawing of P.C. Board Assembly . P.C. Board Component Locations . Monitor Adjustments and Game Board Servicing . Adjustment Instruction Switch Setting Sheet. = SCSI AMNAWNEH CeIdraANWavNNE

SPECIFICATIONS

INSTALLATION SPACE : 31 in, x 27 in. HEIGHT : 73 in, POWER : 225W CRT. : 19" MONITOR MR WEIGHT : 300 Ibs.

NOTE
  • Descriptions herein contained may be subject to improvement changes without notice.

INTRODUCTION TO THE OWNER’S MANUAL

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the SUPER MASTERS, a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.” UP WN my oO EG go g > g aeeaunnee BONES i

Page 3

1, HANDLING PRECAUTIONS When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. + Be sure to turn the power off before working on the machine. « To insert or pull out the plug quickly is dangerous. + Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where so specified. + Do not use any fuse that does not meet the specified rating.

  • Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous. + For protection of the disk, please remove from machine prior to Telocation.

Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.

  • PREVENTION OF COUNTERFEITING AND CONVERSION

LABELLING ! To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.

ORIGINAL SEAL LICENSE SEAL The following seal is put on the The following seal is put on the machines manufactured by kits , such as the printed circuit boards, SEGA. of SEGA products.

SEGA

ORIGINAL SEAU

LICENSE SEAL

16391 4d ae

a qa a

COPYRIGHT NOTICE This SEGA product has the copyright notice as follows:

© SEGA 1989 This signifies that this work was disclosed in 1989 and is the property of SEGA ENTERPRISES, LTD. yoo

Page 4
  • Super Masters
  • PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION The SUPER MASTERS is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage: Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. ]

Places subject to heat sources from heating units, etc., or hot air. j

Vicinity of highly inflammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. * Places subject to any type of violent impact. i Dusty places. eee eee ese

Page 5
  • DISK INSTALLATION
IMPORTANT _

INSTALLATION INSTRUCTIONS

SUPER MASTERS contains a revolutionary new memory system for video games. This memory system is a Floppy Disk System which is housed in the RF Cage. This system allows Sega to give you more memory at a cost effective price.

To insure that no damage occurs to this delicate system during transit, we have packaged the Floppy Disk separately which must be installed upon receipt of the game. Please follow the listed instruction for the installation of the disk.

DISK INSTALLATION

  • Open Coin Door and remove Cash Box.
  • Open Cash Box and remove Floppy Disk. (NOTE: It is housed in a plastic protection cover.)
  • Reach thru the Coin Door opening and unlatch the two spring latches which hold the Control Panel securely to the game. These latches are located on the left and right, inside of the Control Panel Assembly.
  • Once the two latches are unlocked, open the Control Panel and pull out the drawer for access to the PCB RE Cage. (Note: Be sure not to over-extend the drawer.)

5, Remove the cover of the PCB RF Cage by removing the four sheet metal screws.

  • Remove the two screws securing the base of the PCB Assembly.
  • Lift the front side of the PCB Assembly. This will allow access to the disk drive, which is located underneath the PCB.
  • Remove the disk from the plastic protection case and install it into the disk drive label side up with the metal cover protection slide installed first. The disk should slide in and snap down to indicate that it is securely inserted.
  • Replace the two screws that you removed in Step #7 to secure the Wooden PCB base to the RF Cage. 10, Replace the lid of the RF Cage using the four sheet metal screws that were removed from the assembly in Step #6.
  • Push the drawer back into place, and close and latch the Control Panel.
  • Apply power to the game and verify proper operation. This completes the Drive Assembly.
  • For protection of the disk, please remove it from the machine prior to relocation.
Page 6

° Super Masters

~ 5. NAME OF PARTS

PLAYER 1 CONTROL PLAYER 2 DISC.

CONTROL PLUG

DISC. PLUG

Za 56 PIN

Z EDGE SIDEWALL AUDIOVVIDEO [CONNECTOR © HARNESS DISC. PLUG

COIN FRONT HARNESS DISC. PLUG SPEAKER f SS

SIDEWALL AC AND GROUND MONITOR

  • DISC. PLUG Mee CONNECTORS

MONITOR

MONITOR P.C. BOARD

SIDEWALL AUDIO/VIDEO COIN HARNESS DISC. DOOR PLUG

COIN

DOOR COIN FRONT

Disc. HARNESS DISC. PLUG

COIN COUNTER

  • COUNTER DISC.
Page 7
  • ADJUSTMENT OF THE SERVICE SWITCH

The layout as shown below can be viewed by opening the coin chute door.

OPERATING INSTRUCTIONS

TEST SWITCH

VOLUME CONTROL .. Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the game).

. For operating this switch, see SELF-TESTING.

Potentiometer Adjustment

Page 8

a Super Masters

sy 7. SERVICING THE POWER SUPPLY UNIT AND FUSE

Power Supply Assembly

  • P.C. BOARD ASSEMBLY
Page 9
  • SERVICING THE FLOPPY DISK ~

REMOVE THE LID of the SHIELD CASE. Remove the sheet metal and pull out the game board unit in a manner so that both ends of it will meet the shield case. Open the FDD (Floppy Disk Drive) LID by taking off the 2 (M3 x 8) SCREWS when replacing the FLOPPY DISK. _

Page 10

NOT REQUIRED FOR

DIP SW1

837-6443

FDD BD SYSTEM 24

834-6570-05D

MAIN BD SYSTEM 24 SUPER MASTERS

610-0198

FLOPPY DISK DRIVE UNIT

HL-4203 FDD COVER

DS3-5000-05D ! GAME SOFT SUPER MASTERS

  • DRAWING OF PC ASSEMBLY
Page 11

Super Masters :

11, PC BOARD COMPONENT LOCATIONS

SEGA® 837-6442 SYSTEM 24 © SEGA 1987 MADE IN JAPAN

MAIN BD SY 24

I¢1 _Ic2 1G3 Ic4

sw sw2 CN UCN6 CN7 CNB RV1 RV2 EPROM (IC MB27C1000-15) EPROM (IC MB27C1000-15) FOR SYSTEM TC. 68000 IC SECURITY CPU 68000 OR IC 68000 FOR GAME PROGRAM

DIP SW 3 DATA COMMUNICATION CONNECTOR RESERVE POWER CONNECTOR INPUT (SOUND) CONNECTOR HEADPHONE OUTPUT CONNECTOR MAIN SOUND VOLUME HEADPHONE SOUND VOLUME

Page 12
  • Super Masters

i) 12. MONITOR ADJUSTMENT AND GAME BOARD SERVICING

Monitor Adjustment

ic)

Page 13
  • ADJUSTMENT INSTRUCTION SWITCH SETTING SHEET

SUPER MASTERS .

(834-6570-05D) COIN/CREDIT OPTION SWITCH SETTING

1 CREOIT 2 CREDITS 9 CREDITS 4 CREDITS 9 CREDITS 6 CREDITS 1 CREDIT 1 CREDIT 1 CREDIT

1 CREDIT 2 CREDITS S CREDITS 4 CREDITS

1 CREDIT 3 CREDITS

{CREDIT 2CREDITS S.CREDITS CREDITS @ CREDITS

1 CREDIT 2CREDITS 3 CREDITS SCREDITS

1 CREDIT CREDITS 2COINS OFF BARE BD NO. 171-5553, 171-5553-01

gu

DIP SW2

DIP SW 1 SYSTEM 24

MONITOR

HORIZONTAL

PIN ASSIGNMENT

COMPONENT SIDE SOLDER SIDE GND GNO +8 +8 48V +8 +12V +12V COIN METER 1 COIN METER 2 ~ (NOT USED) (NOT USED} ANGLE LEFT (NOT USED} CLUB SELECT (NOT USED) ANGLE RIGHT {NOT USED) . STANCE SFI FCT {NOT USED) SWING DO (NOT USED) SWING D1 (NOT USED) - SWING D2 (NOT USED) SWING D3 (NOT USED)

.SWING D4(NOT USED)
ueSWING D5(NOT USED)-
eeu(NOT USED}(NOT USED)

(NOT USED) (NOT USED) CIA 3440 ~ cont 1P START COIN 2 2P START

TEST(NOT USED)_

SERVICE (NOT USED)

whoowine Gare over.BLUECMP. SYNC~~
1 credit 2 bala. If piayer makes par or better, he gets one ball (Life).GNDGND
LOSE BALL |wore than pr ho wl ona a ball Bas canbe held to 2 bal@NnDGND-

H he runs out of balls, Game over. ‘tr GAME DIFFICULTY = EASY1<EASY2<E ASY3<NORMALcHARD1 <HARD2<HARDS<HARDS

Page 14

~ 14, PARTS LIST

PART NUMBER DESCRIPTION QTy

117-5123 200-5090-MR 390-5120 390-5120-1 420-0009U 421-5800-105 421-6709 421 7209-01 423-0040U 423-0041U 423-0042U 423-0043U 423-0044U 475-0049 509-0004-01 509-0004-02A 509-0004-02B 509-0004-04 509-5028 560-5126 600-5661 600-5672-01 ; a 600-5837 600-5849-04 601-0043 601-0420 601-6073 610-0198 610-0244 834-6570-05D 839-0207 DS3-5000-05D HL-4102 HL-4104 HL-4203 HL-4204 HL-4205 HL-4206 KRO-1721 739902400 800300200 800302000 800800600 801100600 851101000 861100800 880300300 880300500 880300600 880301400 ~~ 880302900 890300100 890300300 991200900 991701400 NAME PLATE, ELEC SPEC MONITOR, 19" FRONT MED RES LAMP, FLUOR FIXTURE, FLUOR MANUAL, SUPER MASTERS ORIGINAL SEAL, SUPER MASTERS STICKER, SVC. INST. STICKER, FDD COVER MARQUEE PLEX, SUPER MASTERS MONITOR CARD, SUPER MASTERS OVERLAY, CTRL PNL, SUPER MASTERS DECAL, SIDE (L), SUPER MASTERS DECAL, SIDE (R), SUPFR MASTERS RHEOSTAT, 100 OHM 10W BUTTON, RED BUTTON, ONE PLAYER BUTTON, TWO PLAYER BUTTON, YELLOW SWITCH, PB MOMENTARY TRANSFORMER, 160P1 CONN, FE 4PX2 ASSY, FEM/FL CA 34P CONN, JST 16P & 9P WIRE HARN 56P, SUPER MASTERS KNOB, 1/8" FILTER. AC LINE RUBBER GROMMET ASSY, FDD UNIT ASSY, CLUB, SUPER MASTERS. GAME PCB, SYS 24 SUPER MASTERS FILTER BOARD, GF GAME SOFT, SUPER MASTERS W/SEC SHIELD LID SHIELD CASE FOD COVER FDD LID SASH RUBBER 110 FDD BASE BRACKET, SERVICE SWITCH WIRE HARNESS, SUPER MASTERS PLATE, LATCH SLANT DRAWER ENCLOSURE, COIN HOUSING PANEL, CTRL HS2 PATTERN M BRACKET, MARQUEE BEZEL, HS1 HS2 PLEX, MNTR 23-11/16 X 23-11/16 HOLDER, FUSE FUSE, 5 AMP 250V SPEAKER, 5” X 7" AMP 8H F12 FOS SWITCH, ON/OFF POWER SUPPLY, 11 AMP LEVELER, LEG LATCH, HC227 ASSY, SLANT DRAWER ASSY, MONITOR FRAME BaP San Pe SC EC ey

a, -13-

Page 15
  • SCHEMATIC DIAGRAM
Page 16

SEGA ENTERPRISES, INC. (USA) 2149 Paragon Drive San Jose, CA 95131 Gov 310° Tel. (408) 435-0201 ye @SEGA 1989