CATHODE RAY TOMES

Knockout Service Manual

Triple Punch (set 1) (K.K. International, 1982) · Document · 23 pages · 10 sections · original scan

Page 1

SERVICE

|IMANUAL

Page 2

TABLE OF CONTENTS

PAGE

I. INTRODUCTION: F.C.C. User Information 1.0... cece cece eee e teen cence ene teen en eeee 1 Game Playing Instructions ......ccecceeee eee enter eens teense tees eseetaas 2

Il. SPECIFICATIONS:

Installation .... cece cece cece eee eee enna tte ee eee eee ee ent tees 3

Electrical Requirements . .3 Power SUPPLY wc cece ccc cece cee eee e eee eee eee eee eee n ene ete enone 3

III. OPERATION:

Routine Maintenance & Service ... cece cece cee ence eee e eect een ee eneene 4

Trouble SHOOting 20... cece cece eee ete e ence eee nent ee een eneneeeees 4 Trouble Shooting Diagram (Fig. 4) ....... cece cece cette eee ee ee eeeeee ees 5

IV. GENERAL Cabinet: Diagram: (Fig. 1) cssvessceccteseansvevvweret sense sctes seceeeees Parts List for Cabinet Diagram ... Cabinet Cross-Section (Fig. 2) Parts List for Cabinet Cross-Section ........ cece eee cece eee e eens ence 9 Control Panel - Exploded View (Fig. 3) Parts List for Control Panel ............

Parts List for Shindengen Power Supply Monitor Service Information ......... cece cece eee e eee eee e eee nee aeee Wiring Harness Diagram

Page 3

“SONSUTAYTLNI FHL LOFYYOD OL G3YINDIY Jd AWW SFBNSWAW YIASLVHM ANWL OL Q3yINOIY 3d TIM 3SN3dX3 NMO SIH LV YISN FHL JSVI HOTHM NI JONIYIINIL -NI 3SMVO OL AVANIT SI WaeW TWILNSGISIY VY NI LNAWdINDI SIHL JO NOTLVYSd0 “FONFYISNTINI HONS LSNIVOV NOILIILOYd JISVNOSWIY JGTAOUd OL GAN9ISIG auv HOTHM “S31NY °9°9°d JO GT LuWd 40 C Luvdans OL LNYNSYNd JONVITdWOd Os G3LSIL NIad LON SWH LI “NOTLWINDFY Ad GALLIWYSd ATIYVYOdWAL SY “SNOTLVOINOWNOD OIGVY HLIM JONSYS4NSLNI 3SNVI AWW LNAWdINDI STHL *T¥ANYW SNOTLONULSNI JHL HLIM JONVGNOIIV NI G3SA ONY GATIVLSNI LON JI *A9USNA AONSNDIYS OLGVY SLVIGWY NWO ONY S3SN ‘S3LWY3N3D LNAWdINDI SIHL SONINGYM NOILWWYOANT Y3SN °9°9°4

Page 4

KNOCK-OUT PLAYING INSTRUCTIONS

You are the Painter. Paint the road by moving the painter with the control lever.

When you paint one complete square, square changes its color and you get score.

Broom moves to erase your painting.

Gorilla and Ghost move randomly to capture you.

Fire turns down at every corner.

Hit one, two, three punches timingly to knock out Gorilla, Broom, and Ghost. Then a rescue car appears to help them to recover. If you knock out the other one while the rescue car is working, you get higher score.

20,000 points gives you another Painter.

Page 5

INSTALLATION

Your game was shipped from the factory in ready-to-play condition.

A brief inspection is suggested before the machine is removed from the

carton. If there is damage to the shipping carton, contact the freight

carrier for claim purposes. External damage could indicate possible

damage to the cabinet and/or electronic components.

After the carton has been satisfactorily inspected, remove the

machine from the shipping carton.

Examine the interior of the game for disconnected wires, cables,

or harnesses. Make sure the electronic (CPU, EPROM, etc.) devices are

securely mounted in their sockets, etc. Record the game serial number

since it will be required for reference and servicing.

ELECTRICAL REQUIREMENTS

Unless otherwise specified, this game is set to operate at 110

volts AC.

Power supply chassis schematic information and parts list are in-

cluded in this manual.

POWER SUPPLY

For most efficient operation of this game, the power supply should

be set so that the voltage on the board is +5.0 volts, + 0.1 volts. To

check this, place a meter across +5.0 volts and ground at the edge

connector. If necessary, adjust the screwdriver control on the power

supply so the meter reads between 4.9 and 5.1 volts.

Page 6

ROUTINE MAINTENANCE & SERVICE

Because of the solid state electronic circuitry, this equipment

should require very little maintenance and only occasional adjustments.

However, it is necessary to take measures to insure this.

TROUBLESHOOTING:

If the game is not functioning properly, check the following items:

Is the fuse intact? (Always use fuse of the designated rating). If the replaced fuse opens again, this indicates another component is defective.

Are there any poor connections (connectors) or open circuits? Special care must be taken to ensure connectors are firmly inserted. Problems due to faulty contacts can exhibit various symptoms.

NOTE: Always turn off the power when inserting or removing the connectors.

If a normal picture does not appear when the power switch is on, reset of the control circuit may be necessary. Check this by turning the power supply switch on and off several times.

When checking counters, switches, etc. with a tester, always disconnect the I.C. board edge connector first.

The video monitor has been properly adjusted before shipping.

Occasionally minor adjustments are necessary. See monitor specifications

and schematics for technical information. Adjustment controls for the

monitor are located at the rear of the monitor.

This machine should be serviced only by a qualified technician.

Do not make any adjustments on this machine while the power js on.

Page 7

TROUBLE SHOOTING

Coin meter does not register. Game will not start when coin is inserted

No . . 1 ~ -]| Is coin switch normal?

Replace coin switch

Yes

Repair wiring Is volume control inside rear service door turned down?

Is there an open in the circuit?

[turn up the

volume control

appear across the coin meter terminals? ~~ F i ‘ v Speaker faulty ives

Is the volume control normal?

Replace volume ontrol

Is there an open in the circuit? t

\

\No {No

Replace coin vv P.C. Board faulty. | Reeue

Yes

| No V. Printed Circuit Board faulty (FIGURE 4)

Page 8

‘Loe een eee

(FIG.1) CABINET

Page 9

oN OD oO fF PART NO.

93-006

92-004

93-005

92-005

92-001

92-001

92-002

92-002-A

91-050

91-051

93-057

91-002

91-003

05-500

91-058

93-001

93-007 PARTS LIST FOR CABINET (Fig. 1)

DESCRIPTION

Header top mounting bracket

Silk screened header

Header bottom mounting bracket

Vinyl trim

Viewing glass

Silk screened monitor overlay

Right hand side decal

Left hand side decal

White Button

Red Button

4-Way joystick with 8-Way option

Coin door assembly

Cash box

Wood cabinet assembly

A.C. line cord harness

Leg leveler (4)

Speaker screen

Page 10

(FIG.2) CABINET CROSSECTION.

Page 11

N

u PARTS LIST FOR CABINET CROSS-SECTION (Fig. 2)

PART NO.

91-062

93-014

91-061

93-008

92-004

91-006

92-001

91-001

93-003

91-057

91-056

91-004

91-002

91-003

91-008

91-005

A - vertical

B - horizontal A or B

AorB DESCRIPTION

Power switch assembly

Incandescent lamp assembly

Incandescent lamp - 25 watts

Vent

Header - plexiglass

Speaker, 5" round, 8 watt, 8 ohm

Viewing glass

19" color monitor assembly

Control panel assembly

Intertock switch

Line filter

Power supply, switching regulator

Coin door assembly

Cash box assembly

Printed circuit board assembly

Isolation transformer

Page 12

may TF ae (FIG.3) EXPLODED VIEW OF CONTROL PANEL.

Page 13

PART NO.

91-050

93-057

91-051

92-003

93-003

93-011

91-052

91-053 PARTS LIST FOR CONTROL PANEL (Fig. 3)

DESCRIPTION

White Button

4-Way Joystick with 8-Way option

Red Button

Control panel overlay

Control panel (sheet metal)

Control panel hinge

Button switch assembly

Pal nut

Page 14

PARTS LIST FOR SHINDENGEN POWER SUPPLY

Transformer, single phase, 2A VA Choking coil, 1.6 mH, 1.5A Choking coil, SF-T8-50S-03 Choking coil, SF-HP-2A-03

Diode, S4Vb40 (bridge type) 28C2504 2SD467 (B) 2SC460 (B) 2SA673 (B) Integrated Circuit, RM723DC or HA17723G-02

Photo coupler, PS2001 watt,

watt,

watt, watt,

watt,

watt,

watt, watt, 18 Ohm.

47K Ohm.

15 Ohm.

56 Ohm.

100 Ohm.

470 Ohm.

0.56 Ohm.

0.82 Ohm.

1/4 watt, 22 Ohm. 1/4 watt, 33 Ohm. 1/4 watt, 68 Ohm. 1/4 watt, 330-470 Ohm. 1/4 watt, 220 Ohm. 1/4 watt, 270 Ohm. 1/4 watt, 330 Ohm. SYMBOL DESCRIPTION

Tl

Li

L2, L4 L3

D1 Diode, V19G D2 Diode, VO6C D3, Dé Diode, 181588 D4 Diode, S15S3 D5, D7 Diode, 5SH1M D12, D13 Diode, F113B 014 Diode, F113B RF1 Ql Transistor, Q2 Transistor, Q3 Transistor, Q4 Transistor, 1€1

PCl

R1 Resistor, 2 R8, R9 Resistor, 2 R3, 1-4 Resistor, 2 R4 Resistor, 1 R12 Resistor, 1 R28 Resistor, 1 R7 Resistor, 1 R26 Resistor, 1

R23 Resistor, R10 Resistor, R27 Resistor, R2 Resistor, R22 Resistor, R21 Resistor, R6 Resistor,

Rll Resistor, 1/4 watt, 68 Ohm. USAGE

PPP BP HEN DMYMHP NYY HEP NH

Pee ee ee eee eee eH

Page 15

Parts List (Cont.) Shindengen Power Supply

SYMBOL DESCRIPTION

R20 Resistor, 1/4 watt, 470 Ohm. R17 Resistor, 1/4 watt, 680 Ohm. R19 Resistor, 1/4 watt, 800 Ohm. R18 Resistor, 1/4 watt, 1.2K Ohm. RS Resistor, 1/4 watt, 10K Ohm. R16 Resistor, 1/4 watt, 220K Ohm. R29 Resistor, 3 watt, 27 Ohm. R39 Resistor, 1/4 watt, 4.7K Ohm. R38 Resistor, 1/4 watt, 5.6 K Ohm. R24 Resistor, 1/4 watt, 330 Ohm. R25 Resistor, 1/4 watt, 150 Ohm. RV1 Variable Resistor, RJ-6P501 C1, C2 Capacitor, ECK-DA1102E C3-1,-2 Capacitor, 160VSN100 c9,C10 Capacitor, SM10VB-2200 Cll, C23 Capacitor, SM10VB-2200 €12,C13,C15 Capacitor, SL25VB-10 C27 Capacitor, SL25VB-10 €18,C19,C20 Capacitor, SM35VB-1000 C26 Capacitor, SM35VB-1000 €21,C22,C€25 Capacitor, SM16VB-1000 c5 Capacitor, DMY21H472K C6 Capacitor, DMY21H C14, C16 Capacitor, DMY21H222K c4 Capacitor, CM20XC511K5 38 Capacitor, MDD22G473K C5-2 Capacitor, DMY21H222K

Fl, F2 Enclosed type fuse, 3A USAGE

PREP MEP RFP WHE WE WNNHNHNHE EP EP eee eee eee

IX}

Page 16

MONITOR SERVICE INFORMATION

K4600 IMPORTANT SERVICE SAFETY INFORMATION

WARNING: An Isolation transformer must be used between the AC supply and the AC plug of the monitor botore ser vicing or testing is performed since the chassis and the heat-sink are directly connected to one side of the AC line which could present a shock hazard. The chassis of the monitor should never be connected to the ground. Belore servicing ts performed, read all the precautions labelled on the CRT and chassis.

X-RAY RADIATION WARNING NOTICE

WARNING: PARTS WHICH INFLUENCE X-RAY RADIATION IN HORIZONTAL DEFLECTION, HIGH VOLTAGE CIR- CUITS AND PICTURE TUBE ETC. ARE INDICATED BY (4) IN THE PARTS LiST FOR REPLACEMENT PURPOSES. USE ONLY THE TYPE SHOWN IN THE PARTS LIST.

PRODUCT SAFETY NOTICE

WARNING: FOR CONTINUED SAFETY REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH MANUFACTURER RECOMMENDED PARTS. THESE PARTS ARE IDENTIFIED BY SHADING AND BY ( a ) ON THE SCHEMATIC DIAGRAM,

AVERTISSEMENT: POUR MAINTENIR LE DEGRE OE SECURITE DE L'APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST GRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

For replacement purposes, use the same type or specified type of wire and cable, ensuring that the positioning of the wires is followed (especially for H.V. and power supply circuits). Use of alternative wiring or positioning could result in damage to the monitor or in a shock or fire hazard. The picture tube used, employs integral implosion protection and should be replaced with a tube of the same type number for continued safety. When handling the CRT, shatter-proot goggles must be worn after completely discharging the high voltage circuit. Do not lift the picture tube by the neck.

PERFORMANCE AND OPERATING DATA

Apply a suitable power source to the monitor through an isolation transformer.

  • Apply a suitable signal source to the monitor PCB by means of P205.
  • Set up Controls. All controls are preset at the factory, but may be adjusted to suit program material.

1.0 Supply

Voltage 108 VAG - 132 VAC

Frequency 50 Hz -60 Hz

Note: Apply supply voltage through an isolation transformer with 1 Amp. capability.

2.0 High Voltage (EHT)

For 19"'V models 25.5 + 0.8 K.V. at 0 Beam

Note: Condition for above 1(beam) = 0 AC. = 120V
Page 17
  • Service Set-Up Controls

G. Screen Control = VR406 H. Video Drive Controls - Red Drive = VR401 Green Drive = VR402 |. CRT Cut Off Controls - Red Cutoff = VR403 Green Cutoff = VR404 Blue Cutoff = VR405

SERVICE INSTRUCTIONS

A.V. Adjustment VR501 set for 127V OC B. Vertical Size Cont = VR302 C. Vertical Hold Cont = VR301 D. Horizontal Hold Cont = VR351 €. Horizontal Width Cont = L702 F. Focus Control = VR702

FOCUS Adjust the Focus control (VR702), located on the HV unit (1701), for maximum over-all definition and fine picture detail.

+127V ADJUSTMENT (See Fig. 1) The + 127V adj. contro! (VR501) is adjusted at the factory. However, if readjustment should be required, proceed as follows.

  • Operate monitor for at least 15 minutes at 120V AC line.
  • Connect Positive lead of V.T.V.M. to blue lead of TR502 negative lead to chassis ground.
  • Adjust VR501 to obtain + 127V reading.
  • After adjustment VR501 must be locked with a sealing varnish. VR501 +B Ad) i

Emitter

Chassis Ground

FIGURE 1 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention. If however when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper biack level! (the black portion of the picture just extinguished). VERTICAL SIZE (HEIGHT) The vertical height control is a screw-driver adjustment. Location of this control is shown in Fig. 3. This control must be adjusted slowly, if necessary. until the picture or test pattern attains the correct vertical proportions CIRCUIT PROTECTION A3.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.

HORIZONTAL OSC. ALIGNMENT (See Fig. 2) A warm-up period of at least five minutes should be allowed before alignment is carried out. Set VR351 to center position. Adjust L351 after grounding R328 plug. (TP32 of Vert/Horiz. P.C. Board) through a 1uF/50V capacitor. Adjust L351 to obtain normal picture. After adjustment, remove 1uF/50V capacitor

5OV/1uF

Chassis Ground A328 (6P Plug for PC Board Side} TP32

wast Hang to 4@ y Cabinet Sie

FIGURE 2

Heat Sink Ass y Auddio/Power (MV-3)

Vea Honz Board (QJ 21 Sewce hp S PL Board ~ Service Ty NW Holter YR402 Blue Drive Contiol Ae R801 Red Drive Control

  • /— yRa0S Blue Cut a8

7 Off Convo! ~ ¥R404 Green Cut OW Control jg --- vA403 Red Cut ‘ ‘olf Control VA301; vy

J V Hold! vR302 V Size,

R406 Screen Control VA35° Pepe Nawk Board OG?

FIGURE 3

Page 18

INSTALLATION AND SERVICE INSTRUCTIONS

COLOR PURITY AND VERTICAL CENTERING ADJUSTMENT

For best results, it is recommended that the purity adjustment be made in the final monitor location. If the monitor will be moved, perform this adjustment with it facing west or east. The monitor must have been operating 15 minutes prior to this procedure and the faceplate of the CRT must be at room temperature. The monitor is equipped with an automatic degaussing circuit. However, if the CRT shadow mask has become excessively magnetized, it may be necessary to degauss it with manual coil. Do not switch the coil OFF while the raster shows any effect from the coil. Purity Magnets are used for Color Purity and V Centering Adjustment. Purity Adjustment procedure is as follows.

  • Remove R-G-B signal from monitor.
  • Turn Green Cut off Control (VR404) on the Neck Board fully CCW. Turn Red and Blue Cut off Controt (VR405) fully CW. 3, Pull the Deflection Yoke backward so that the Magenta belt will appear. (See Fig. 4)
  • Move the two Purity Magnets and bring the Magenta belt to the mechanical center of the screen (See Fig.
  • The vertical center position should be set VRS to —5/64" (—2 mm) as shown in Fig. 6. Insert service tip “‘N” on Neck circuit board to “S” on Vert./Horiz. circuit board (See Fig. 13). To check, use the Green raster at low intensity. Be sure to return the service tips to their original positions for the next check.
  • Push the Deflection Yoke forward gradually and fix it at the place where the Magenta screen becomes uniform throughout.
  • Turn Cut off Control, and Drive Control and confirm that each color is uniform.
  • If the color is not uniform, re-adjust it moving Purity Magnets slightly.
  • Move a pair of Purity Magnets at the same time (do not change the angle of the pair), and adjust the vert. center to center of screen.
  • Obtain the three colors and confirm whether white uniformity is balanced.
  • Insert the temporary wedge as shown in Fig. 5 and adjust the angle of Deflection Yoke.

STATIC CONVERGENCE ADJUSTMENT

A recently deveioped Deflection Yoke and Electron Guns construction has been used on this equipment in combination with In-Line Guns and Black Stripe Screen to make a barrel-type magnetic-field distribution for vertical deflection and a pin-cushion-type magnetic field for horizontal deflection with which a_ self-converging system can be obtained. This type is different from conventional unity-magnetic field distribution type deflection yoke. 4-Pole Magnets and 6-Pole Magnets are employed for static convergence instead of a Convergence Yoke.

  • A cross hatch signal should be connected to the monitor.
  • A pair of 4-Pole Convergence Magnets are provided and adjusted to converge the blue and red beams. When the Pole opens to the left and right 45° symmetrically, the magnetic field maximizes. Red and blue beams move to the left and right oppositely (See Fig. 7-a and 7-b). Variation of the angle between the tabs adjusts the convergence of red and blue vertical lines. When the both 4-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of the red and blue horizontal lines is adjusted.
  • A pair of 6-Pale Convergence Magnets are also provided and adjusted to converge the magenta (red + blue) to green beams. When the Pole opens to the left and right 30° symmetrically, the magnetic field is maximized. Red and blue beams both move to the left and right (See Fig. 8-c and 8-d). Variation of the opening angle adjusts the convergence of magenta to green vertical lines. When both 6-Pole Convergence Magnet Tabs are rotated as a pair the convergence of magenta to green horizontal lines is adjusted.

PRECISE ADJUSTMENT OF DYNAMIC CONVERGENCE (See Fig. 10 and 11)

  • Feed a cross hatch signal to the monitor.
  • Insert the temporary wedge and fix Deflection Yoke So as to obtain the best circumference convergence (See Fig. 10 and 11).
NOTE: The temporary wedges may need to be moved during adjustments.
  • Insert three rubber wedges to the position as shown in Fig. 9 to obtain the best circumference convergence.
NOTE: 1)_ Tilting the angle of the yoke up and down adjusts the crossover of both vertical and horizontal red and blue lines. See Fig. 10 (a) and (b).
  • Tilting the angle of the yoke sideways adjusts the parallel convergence of both horizontal and vertical lines at the edges of the screen. See Fig. 11-a and b.
  • Use three rubber wedges (thick and thin rubber wedges are used for a purpose).
  • The angle of each rubber wedges are shown in Fig. 9.
  • After three rubber wedges have been inserted, pull out the temporary wedge.
  • Fix the rubber wedges with chloroprene rubber adhesive.
Page 19

INSTALLATION AND SERVICE INSTRUCTIONS

BLACK AND WHITE TRACKING (With R/G.B. inputs grounded) 4.

  • Set Black Level Controi (VR201) to mid point. 5s
  • Set Red and Blue Drive Controls (VR401 & VR402) to their mechanical center.
  • Set the G2 Screen Controi (VR406) and the 3 Cut-off Controls (VR403, VR404, & VR405) to minimum

Temporary Wedge

Magenta Beit

FIGURE 4 FIGURE 5

N

S

4.Pole Magnets and the Movement of Beams

FIGURE 7

~17- (ccw). Slowly turn up G2 screen control until the first taint color appears. Slowly turn up the other two color cut-off controls in turn to match the first. ° Remove ground from R/G/B/ inputs. Adjust Red and Blue Drive Controls (VR401 & VR402) for white screen.

Mechanica Center

  • ——|-t vas ct “p58 Green Beam ‘mm

FIGURE 6

6-Pole Magnets and the Movement of Beams

FIGURE 8

Page 20

INSTALLATION AND SERVICE INSTRUCTIONS

/~ Temporary Wedge

[Detlection Yoke

FIGURE 9

acAr \ RGB

R—Bi8R
GGcRTyG.G
B aeRk°| RB

RGB A oer | BGR —_ we

  • 0) CRT Screen Insert Rubber Wedge CRT Screen trom Upper Side

FIGURE 10

CRT Screen insert Rubber Wedge CRT Screen trom Left Side

FIGURE 11 \ cRT Upper

CRT

Under

insert Rubber Wedge from Lower Side

/ a

Insert Rubber Wedge from Lower Side

Page 21

INSTALLATION AND SERVICE INSTRUCTIONS

R406 Screen

VR: Sue VR403 Red Cut Off

vagor VR404 Green Cut OIF V Hog vr4o1 R351 B \ VR405 Blue Cut Off A-Orve H Hold | Ef) R352 \ vasoe

™ ~

VERT./HORIZ. BOARD |M.

FIGURE 12

ANODE CONTACT

(675mm = gle

  • 6 POLE CONVERGENCE MAGNETS INVERGENt ~ 4 POLE CONVERGENCE MAGNETS | ee, penta ~ * PURITY CENTERING MAGNETS: | . . L

DEFLECTION YOKE

= RUBBER WEDGES

FIGURE 13. PICTURE TUBE NECK COMPONENTS LOCATION

Page 22

PART SIDE

UNIV. PIN FUNCTION

  • + 5V

2P Left 2P Right 2P Up 2P Down 2P Shoot

2P Start 1P Start Mon Green Mon Red Mon Blue Mon Sync +12V Ground Ground NN PHONON MANY mo any KNOCKOUT

COLOR PIN PIN

WHT/RED 1 A 2 B 3 Cc 4 D 5 E 6 F 7 H 8 J 9 K

Qrange 10 L Wht/Yel 11 M Green 12 N

Red13Pp
Blue14R

White 15 S Violet 16 T Wht/gray17 U

Blk18.v
NOTE: SHORT TOGETHER PLAYER 1 & 2=FUNCTIONS

Coin/4 Credits "738 0 nD» 0 » 7s " TABLE UPRIGHT 6 Persons 5 u a" 0

AUTOMATIC PLAY MODE TEST GAME Hee SW1 N/U

SOLDER SIDE

COLOR FUNCTION

WHT/Red + BV

WHT/Blue 1P Right WHT/Vio 1P Left Yellow 1P Up Brown 1P Down Wht/Brn 1P Shoot

Yellow Service Wht/Org Coin 1 Wht/Blk Coin Ctr.

Gray Speaker

Gray Ground Blk Ground

DIP SWITCH SETTINGS

SW2 SW3 SW4 — SW5

off off on off off on on on off _ on off on off on SW6 SW7 SW8

off off on on off on off on UNIV. PIN

(17)

25)

(11)

12) (21)

Page 23

UNIVERSAL HARNESS

Assigned Color Coded

Pin #WireFunctionConnector

Power Supply:

Monitor: J3-10Pin

5RedTV Red1
6GreenTV Green2
7BlueTV Blue3
8WhiteSync Y10
9Wht/GrySync H9
10BlackGround for Mon4

Speaker: J4-2Pin

11GrayAudio1
12GrayAudio Ground2

Cein Assembly: J1-9Pin

13BlackGround1
14BlackGround2 - To SPS
15Wht/OrgCoin Switch3
16Violet+ 12 Volts4 - To SPS
17Wht/Red+ 5 Volts5 - To SPS
18Wht/Grn- 5 Volts6 - To SPS
19YellowTest7
20Wht/B1kCoin Counter8

Control Panel: J2-12Pin

21BlackGround1
22Orange1P Start2
23White/Yellow2P Start3
24White/VioletLeft4
25White/BlueRight5
26YellowUp6
27BrownDown7
28White/BrownFire(1)8
29White/BlackBomb(2)9

30,31 White/B1k/Brn (Function 3,4) 10,11