CATHODE RAY TOMES

Indy 800 TM-026

Indy 800 (Atari/Kee, 1975) · Technical Manual · 96 pages · 39 sections · original scan

Page 1

‘4 "INDY BOO

Service

©1975 ATARI, INC.

Page 2

In no event shall Seller be liable for loss of profits, loss of use,

incidental or consequential damages.

incidental or consequential damages EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN

CONTRACT BETWEEN SELLER AND WHICH

This document is and contains confidential trade secret information of

Atari, Inc.

This document is loaned under confidential custody for the sole

purpose of ion, maintenance and

Page 3

Warranty, Table of Contents

Section 1 General Maintenance Information

1-1

1-2

1-3

1-4

1-5

Section 2

2-1

2-2

2-3

2-4

2-5

2-6

2-7

2-8

Section 3

3-2

3-4

Section 4 Introduction

New Machine Set-up Procedure

New Machine Checkout

Coin Acceptor

General Machine Maintenance

Circuit Description

General System Description

SYNC Printed Circuit Board

Score Printed Circuit Board

Coin Control Printed Circuit Board

Car Printed Circuit Board

Power Supply Printed Circuit Board

Operator Adjustments & Instructions

Service and Troubleshooting

Customer Service Information

Test Equipment Required Minimum Equipment Optional Equipment Logic Types and Functions

Schematics, Drawings and Parts Lists Page

Inside Front Cover

1-1

1-1

1-1

1-2

1-3

2-1

2-5

2-8

2-10

2-13

2-19

2-19

2-21

3-1

3-2

3-2

3-3

Page 4
  • GENERAL MAINTENANCE INFORMATION

1-1. INTRODUCTION

The Atari Indy 800 game consists of a cabinet, TV monitor, printed circuit boards (PCBs), interconnecting wiring, and various cabinetmounted circuit components. Except for a schematic, no information about the TV monitor is presented in this manual. The TV monitor is a GE 25" color unit. TV circuit malfunctions can be solved using standard TV troubleshooting techniques. However, the PCB computer requires troubleshooting techniques that may be unfamiliar to the average technician. Therefore, the troubleshooting information in this manual is dedicated to the PCBs and their associated cabinet circuitry.

1-2. NEW MACHINE SET-UP PROCEDURE

Before turning this machine on, inspect it carefully for any damage which may have occurred during shipment. Inspect both interior and exterior of the machine for any obvious damage to the cabinet or internal components. Check for cracked or broken cabinet parts, assemblies pulling loose, broken or disconnected wires, or foreign objects shorting electrical connections. After the machine has been plugged in and turned on, perform the checkout procedure.

1-3. NEW MACHINE CHECKOUT

As each new machine leaves the factory, every component and subassembly is carefully checked for proper operation. However, since parts may have been damaged or adjustments changed during shipping, the following checkout procedure must be repeated prior to placing the machine on location:

  • Inspect both the exterior and interior of the machine for obvious shipping damage such as cracked or broken cabinet parts, subassemblies broken loose, etc.
  • Carefully inspect the interior of the machine to see that all solder joints, slip-on connectors, and plug-in type connectors are firmly seated. Pay particular attention to the PCB edge connector and the fuses. Also check the connections to the coin switch, the TV monitor, the interlock switches, and all other Molex-type connectors.
  • Plug the machine in, and pull out the white actuator shafts of the interlock switches if the rear door is open. Inspect the cathode ray tube image for a steady and sharp picture that exhibits the proper levels of brightness and contrast.

1-1

Page 5
  • Insert several old and new coins into the coin acceptor. No genuine coin should be rejected, and each coin insertion should step the coin counter one digit. Depress the coin rejector button to make sure that the linkage is operating smoothly.
  • Coin insertion should start the game. Check for proper game sequence, making sure that all aspects of the game are functioning correctly.
  • The interlock switch must turn off the entire machine when the rear door is opened.

1-4. Q-530 COIN ACCEPTOR: OPERATION, ADJUSTMENT & MAINTENANCE

All coin acceptors leave the factory adjusted for maximum performance. If, however, more critical adjustments are desired, or if the unit has been completely disassembled for service, the following adjustment procedure is suggested. If the coin acceptor has been removed from the machine, place it in a vertical position on a level surface. If the acceptor is still mounted on the coin door, place the coin door in a vertical position on a level surface.

  • Kicker and Separator

a. Set the acceptor with the back of the unit facing you in the test position. b. Loosen the screws holding the kicker (1) and the separator (3) and move both the kicker (2) and the separator (4) as far to the right as they will go. Tighten the screws. ec. Insert several test coins (both old and new) and note that

some are returned by striking the separator. d. Loosen the separator screw and move the separator a slight amount to the left. Tighten the screw. e. Insert the test coins again and, if some of them are still returned, repeat Step d until all the coins are accepted. f. Loosen the kicker screw and move the locker as far to the

left as it will go. Tighten the screw. g- Insert the test coins and note that some are returned.

h. Loosen the kicker screw and move the kicker a slight amount to the right. Tighten the screw. i. Insert the coins again and, if some are still returned, repeat Step h until all the coins are accepted. j. Be sure that both screws are tight after the adjustments have been made.

1-2

Page 6
  • The Magnet Gate

a. Set the acceptor with the front of the unit facing you in the test position.

b. Turn the magnet gate adjusting screw (2) out or counterclockwise

until none of the coins will fit through. c. With a coin resting in the acceptor, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. d. Test this adjustment using several other coins, both old and new, and if any of them fail to pass the magnet gate, repeat Step ¢ until all the coins are accepted. e. Fix the magnet gate in this position with a drop of glue or Loctite, if necessary.

  • Acceptor Maintenance

Depending on the environment in which the acceptor is used, periodic preventive maintenance should be performed. The mainplate (5) may be cleaned with any household cleaner. Thorough rinsing and drying are necessary to remove deposits and/or film. Remove all metal particles from the magnet by guiding the point of a screwdriver or similar tool along the edges of the magnet. You will notice that the particles will cling to the point of the tool. Remove the transfer cradle (9) and the undersize lever (10) and clean the bushings and the pivot pins. A pipe cleaner is an effective cleaning tool. Apply powdered graphite or pencil lead to the pivot pins and bushings and reassemble. Spray the entire unit lightly with wo-uc® , a iubricant.

1-5. GENERAL MACHINE MAINTENANCE

Due to its solid-state circuitry, your machine will require very little maintenance other than periodic cleaning, lubrication and TV monitor adjustment. The cabinet and plexiglass screen may be cleaned with any non-abrasive household cleaner. The coin acceptor and the rejector linkage should be sprayed lightly once every three months with wo-4o® or a silicone lubricant. The potentiometer shafts must never be lubricated in any way. The TV monitor is adjusted only when the CRT picture is distorted, or if the contrast or brightness appear to be out of adjustment.

Page 7

KICKER SCREW KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRADLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING UPPER GATE PIVOT SPRING

GATE PIVOT PIN

WIPER LEVER SPRING WIPER LEVER WIPER

e Se few bine

COIN MECHANISM ~ EXPLODED

Page 8
  • CIRCUIT DESCRIPTION

2-1. GENERAL SYSTEM DESCRIPTION

  • The Indy 806 electronics system consists of the following components:
Part/Assy No.Qty.DescriptionSectionPage
A0031821Syne PCB2-22-5
A0031701Score PCB2-32-8
A0031841Coin control PCB2-42-10
A0030008Car PCB2-52-13
A0031991Backplane PCB2-12-4
A0031911Power Supply PCB2-62-19
A0006078Steering PCB2-12-4
A0031931Remote panel PCB2-42-11
92-013125" color TV monitor—---
Harness §& controls---——-

The sync, score, coin control, and eight individual car boards are housed in a card rack within the game. These PCBs are interconnect-~

ed by the backplane circuit board which is located at the rear of the card rack. The backplane board also provides edge connectors for interfacing with the other system components through the harness. Figure I-A shows the locations of the various boards and connectors within the card rack. The car numbers, colors, and steering wheel locations as well as locations of the card rack and power supply are shown in Figure I-B.

  • Basic functional description of each PCB a. Sync PCB This includes the system clock, the video sync counters, and timing function generators, the race track video, the score checkpoints, score video windows, and the ORing circuitry for detection of collisions with other cards. The master

audio volume control is also located on this board.

2-1

Page 9

2-2

From Remote Panel

and to Television

Power

Ce for Cars 1-4 Monitor

J1 J2

Master Audio

Volume Switch

C Score Board

Car Board 4 (

Car Board 1 (Blue. ar Board 2 (Red)

) Car Board 3 (White) Light Blue) ce I/o I/O for Cars 5-8

J4

  • S&F

Car Board 5 (Green)

Coin Control Board Car Board 6 (Yellow) Car Board 7 (Peach) Car Board 8 (Purple)

Figure I-A: Indy 800 Card Rack Layout (Front View)

Page 10

Figure I-B: Indy 800 Cabinet, Location of Car Controls and Electronics

Page 11

Score PCB This includes all the circuitry necessary for detecting, counting, and displaying the score for each car. It also senses which car has the highest score and causes that score to blink. Finally, it contains the video outputs to the TV (except sync) and the TV calibration function circuit.

Coin control PCB

This monitors all coin inputs. It generates the reset and enable for each car in both the attended (with remote panel) and unattended (coin input, automatic) modes. The game timer and game tum-off circuitry are also included on this board.

8 identical car PCBs

These control each of the individual cars. Each board contains

all the circuitry necessary to rotate, move, and produce the video and audio for one car when enabled. The skid, collision, and crash detectors are also on this board.

Backplane board This has no electronic components and serves only as an interface between the various components of the entire system.

Power supply PCB This is the source of the unregulated power supplies for the digital and analog circuitry of the other boards. The relays and drivers for the coin mechanism lockout coils are also located on this board.

Steering PCBs These are mounted on the backside of the steering wheel assemblies. The boards use optical sensing to produce two signals in quadrature, which may be decoded into rate and direction of rotation.

Remote panel This is simply a switch board which is used to control the game in the attended mode of operation. Individual car enables, a master enable, and a start button are provided. When the remote panel is disconnected, the game automatically reverts to the unattended or automatic mode.

Page 12

2-2. THE SYNC PRINTED CIRCUIT BOARD

The sync PCB has circuitry to produce the following functions:

  • System CLOCK and video countdown chain.
  • COMP SYNC signal to TV monitor. Race track video.
  • Score CHECKPOINTS.
  • SCORE WINDOW.
  • OTHER CARS signal for each car.
  • +5 volts power for steering boards.
  • Miscellaneous timing signals to other logic.
  • MASTER VOLUME CONTROL signals.

The system CLOCK runs at 14.3 MHz. The horizontal countdown chain A¥ Bu, Cu (9316s) divides this basic frequency by 908 for each video line (15.76 KHz). The vertical countdown chain D4, D4 (7493), E3 (74107) divides the line rate by an additional 263 for a video frame (60 Hz).

The horizontal counter starts at 116 (binary 0001110100) and counts to 1024 (1111111111). The horizontal sync pulse (HSYNC) begins at count 256 and is 64 clock pulses wide (4.47 .sec). This is dome at C3-9 (7474) where the rising edge of 256H clocks a low through to Q, which is set back to a high 64H later by B3-11 (7400).

The vertical counter counts from zero (binary 000000000) to 262 (100000110), at which time D3-12 (7410) goes low. At the next rising edge of 512H, this low is clocked through to C3-5 (7474). VRESET then resets the vertical counters to zero and the cycle begins again after VRESET is cleared again one line later. The vertical sync pulse (VSYNC) comes from an R/S flip flop, D3-1 (7202). It begins with VRESET and is 4s lines long (290 sec).

The race track signal (RT) is generated by feeding sync counter signals into a 1K ROM, F4 (003189). The 4-bit output is multiplexed to a single line by F3 (74153) and is gated by 512H and by a signal to produce "dots" from A3-8 (7420).

Similarly, the score CHECKPOINTS come from a 256=bit ROM, E5 (003188) which is addressed with functions from the sync counters. The three

lowest-order data outputs of this ROM are used to generate the score windows in which the score video will be shown. This generation is

2-5

Page 13

accomplished in some random logic including Al (7400), Bl (7486), and finally out of C1-8 (7420).

COMP RESET CLOCK is a signal which drives the car reset circuitry on the coin control board. It is a signal that occurs at horizontal count 544 through 1024 on one line out of every 12. Dl (74107) is hooked up as a divide-by-3 counter to produce a 4~line signal every 12 lines. B2 (7400) is hooked up as an R/S flip flip to produce the proper horizontal timing. These are ANDed together along with 1V and 2V signals to produce the

required signal at Cl-6 (7420).

BOUNDS is a signal that represents a horizontal boundary. It goes to the car reset circuitry on the coin control board. Any car found coincident with this signal is out of bounds and will be reset back to the starting line.

FLASH is a 4-bit (250 ysec) squere wave used to make the score of the leader blink.

16V > 32H is a timing signal used in the generation of the score video. It is a digit select signal that multiplexes the high- and low-order digits of the score.

The OTHER CARS signals are a three-level ORing of every car except the one to which the signal is sent. They are used on the car boards to detect collisions between cars.

¥CLOCK is a two-pulse signal during horizontal syne on each line (except those lines from 256V until the end of VSYNC). It is used to clock the

vertical-motion counters on the car boards.

MASTER VOLUME signals choose one of four possible volume levels for all

cars.

See Figure II-A for a diagram of the syne functions, race track, etc., as oriented on the TV screen.

2-6

Page 14

2-7 = coer 77Z5 eoccee WY) ¥° eccce

Window- (8 Places) \ -Pt. eco eee e \

e e e

° e *8 o8

ee eh X

: te

A ©

l

64v-——_—_l OL SLE 28y@__ A Sev —I : : H

Ch. Pt. O08 06 00 00 OOO OOCCE

secceee

Figure II-A: Sync PCB Functions

Page 15

2-3. THE SCORE PRINTED CIRCUIT BOARD

The score circuit board includes several subcircuits that detect, count, and display the score as well as detect the leader. Each car has 6 bits of score arranged in two digits of 3 bits each. The three least signi~ ficant bits (nC, nB, nA, where n = car number) represent an even decimal digit from zero to 8 and are the signals from the divide-by-5 outputs of a 7490 decade counter. The three most significant bits (nF, nE, nD) are the outputs of a divide~by-8 counter configuration and they represent a decimal digit from zero to 7. Thus, the score for each car runs from 00 to 78, counting by twos.

Score is detected by sensing that the car crosses a series of "checkpoints" in a certain sequence. These checkpoints are generated on the sync board and are located at appropriate places along the race course (see sync board, Section 2). The detection of coincidence between car and checkpoints in the proper sequence is provided by a 9312 IC, an eight-input multiplexer, The circuit is shown in Figure III-A. Depending on the least significant digit (3 bits) of score, the next checkpoint to be crossed is selected.

From the score counters, the score bits are time-multiplexed in another stage of six 9312s so that each score is present at the output of the multiplexers when it is to be displayed on the screen. This time-multiplexed score information is then fed into two circuits -- the leader detector circuit and the seven-segment decoder.

The leader detector circuit operates as follows (see Figure III-B). At the start of a game, all of the score counters and the latches K2 (74175) and H2 (74174) are reset. H2 contains the high score bits and K2 contains a code telling which car first achieved that score. At each video frame all the scores are compared to the highest score by comparing the multiplexed score bits (A through F) with the outputs of H2. This comparison is made in the digital comparators J2 and F2 (7485). When the incoming score exceeds the previous high score, an output of the comparator is gated with some sync signals in C6 (7410) to avoid race conditions. The resulting signal clocks H2 and K2 to store the new highest score and new-leader code.

2-8

Page 16

Least Significant Score Bits ch. Pt. Sw wu

76543219 sa" INPUTS

9312

CARN

Figure III-A: Score Detection Circuit

Fr NO LEADER LEADEL 101

CraDeR £02

LEADER 1D>

x PrP OOF F OO XK FoF OF ORO *K ooo oceco coo Uannr ® own bw

*No-leader condition is present only at start of game.

Figure III-B: Leader Detector Circuit

Page 17

The time-multiplexed score is further multiplexed into two digits in Hl (9322) and this information is fed into a seven-segment decoder, Fl (7448). A digital comparator, L2 (7485), is used to make the score of the leader blink by exciting the blanking input of Fl when the LEADER I.D. code matches the time-multiplexed sync signals (256H, 64V, 128V).

Four 74153s (Al, Bl, Dl, El) and three 9312s (A2, B2, C2) are the function generators that translate the multiplexed seven-segment data into score video information. El and Bl form the seven-segment characters for scores 1, 2, 5, and 6. £1 (74153) forms the vertical segments b, c, e, and f. Bl (74153), together with a blanking signal from B2 (9312), forms the horizontal segments a, d, and g. These are ORed in Cl (7432): Cl-11 has the video for scores 1 and 2; Cl-8 has the video for scores 5 and 6. Similarly, Dl (74153) forms the vertical segments for scores 3, 4, 7, and 8, and Al (74153) and A2 (9312) produce the horizontal segments. These are again ORed in Cl (7432): Cl-6 has the video for scores 3 and 4; Cl-3 has the video for scores 7 and 8. These separ~ ate video signals are remultiplexed in C2 (9312), where the score window from the sync board is used to gate the information through at the proper time.

This composite score video signal is then demultiplexed in D6 (9301) into eight separate score video signals. These signals are then ORed with the car signals in E6 and F6 (7408), ANDed with the video function SIGNAL, and sent out to the television as video information. There is sane slight additional circuitry that creates video test and alignment functions on the white video output line (car 3). These functions are: normal operation, all-white screen, all-black screen (no video), and a dot pattern for convergence adjustment. They may be selected by attaching the appropriate jumper as shown on the schematic.

2-4. COIN CONTROL PRINTED CIRCUIT BOARD

The coin control circuit board contains the circuitry for the following funetions:

  • Coin detection and credit latches.
  • Game control, game timer.
  • Car reset circuitry.

2-10

Page 18

The heart of the coin detection and credit latch circuitry is the LM339 quad analog comparator. This device is used to sense a proper coin input and to latch and register credit for that coin until the end of the game. Normally open and normally closed coin inputs are brought into an inverter latch where the coin signal is debounced.

When the coin switch is closed, the 0.1 pe capacitor on the non-inverting (+) terminal of the LM339 is discharged through a 68K resistor. If the switch is closed for more than 12 msec, the voltage at the non-inverting terminal of the 1M339 will go negative with respect to the inverting (-) terminal voltage (ref. Voltage). When this occurs, the output of the 1M339 changes state. Through positive feedback, this state is latched into the comparator. If the coin switch is closed for less than 6 msec, the capacitor will not discharge sufficiently to allow the output of the LM339 to change state. Between 6 and 12 msec, the latching may or may not take place, depending on device tolerances. The typical duration of coin pulse needed to toggle the latch is 10 msec. At the end of the game, or in case of a power or static interrupt, the REF voltage at the inverting (-) comparator input is pulled low. The output again goes high, and the 0.1 pf capacitor is quickly recharged through a diode.

The game control circuitry determines which cars are enabled in all modes of operation. There are three basic modes of operation:

  • Unattended (automatic).
  • Attended with coin inputs, remote start.
  • Attended with remote enable and start.

In the attended mode, the remote panel is not used. In the first attended mode the start button on the remote panel is used, but the enable switches are not (they should all be turned to the "off" position). The second attended mode assumes manual collection of money by the attendant. The lockout coil switch on the power supply board should be turned to "off" so that no money can be put into the machine. The attendant then enables any or all of the cars by turning the appropriate switches on the remote panel and pushing the start button.

2-11

Page 19

The coin board determines whether it is in the attended or unattended

mode by seeing if the remote panel is connected to it. If the remote panel is connected, then the REMOTE signal will be low (provided by a grounded jumper in the remote connector). Otherwise REMOTE will be high or pulled up. This signal goes to a 9322 quad two-input multiplexer (D2) that selects the proper control functions for required mode of operation.

In the unattended or automatic mode of operation, if any coin has been put into the machine, CREDIT is high (from CREDIT 1, IC C5, 7430). When CREDIT goes high, the game counters Kl, Jl (7493s) start counting. After eight pulses from the 1 SEC oscillator, Ll (555), the PLAY 1 latch H1-10 and K1~13 (7402) changes state and the game starts.

If the game is in the play mode and car n has credit (Qn is high), then ATTRACT n will go low (ICs H4 and F4, 7400). This enables the controls on car n so that it may be driven. During the eight-second waiting period, the SCORE RESET signal is driven low by C2-8 (7410). At the end of the game, after 128 pulses from the one-second clock, the END GAME latch H1-4 (7402) produces a pulse to reset the credit latches.

In the attended mode, the START signal clocks the CREDIT 2 flip flop at C3-11 (7474). If any coin latches are set or remote enable switches are in the "on" position, CREDIT and PLAY will go high. The score will be reset by the START signal. At the end of the game, the END GAME latch (H1) will reset the CREDIT 2 flip flop (C3) through C2-4 (7410).

The car reset circuitry resets each car at the start of the game and if it travels out of bounds. COMP RESET CLOCK shifts a series of high signals through the 8-bit parallel out-shift register, C4 (74164). As the high signal ripples through the shift register on consecutive pulses from COMP RESET CLOCK, the individual car reset clocks (CRC 1 through CRC 8) are produced. These are used to clock the car reset flip flops A3, A4, B3, B4Y (7474s). If coin switch n is closed or if car n is out of bounds, the set input of car reset flip flop n will be pulsed low, and CAR RESET n will go high. If the game has credit but car n does not, then the D-input to the reset flip flop will be held high and CAR RESET n will be continuously clocked high by CRC n. As long as the CAR RESET signal is high, carn will disappear. Then credit for carn is established, CAR RESET n will be clocked low, and the car will reappear at the starting line.

2-12

Page 20

2-5. CAR PRINTED CIRCUIT BOARD

The car board contains the following circuits:

  • Car steering processor.
  • Car acceleration processor.
  • Car motion counters.
  • Car video processor.
  • Crash and collision detection.
  • Sound synthesis and power amp.

The steering processor is a two-stage up/down counter (E2 and F2, 74193s) with decoding circuitry in front (E3, 7474, and El, 7300) and the skid detector (C1, 7400) and latch (D1, 7475) after. When the circuit is enabled (attract goes low), the decoder circuitry translates a quadrature signal from the steering board into direction and rate of turn information -- see Figure V-A). VIC on E3-13 (7474) serves as a maximum turning vate signal.

When there is a collision between cars, El-6 (7400) forces the car to turn for the duration of the COLLISION signal at the maximum turning rate. The red LEDs on the outputs of H4-10, 12 (7414) serve only as visual indicators of the operation of the quadrature signal from the steering board. E2 and F2 (74193s) divide the rotation pulses of the decoder circuit by 128. The last five bits of this division become the rotation code R4-RO* that represents a specific car orientation. Binary 00000 is straight up; the count continues clockwise through 32 consecutive positions up to binary 11111, which is just left of straight up. The skid latch Dl (7475) contains the direction code* of the car or D4-D1 (the lowest-order direction bit is RO).

*The rotation code R4u-RO tells in which direction the car is pointed; the direction code D4-Dl, RO tells the direction of motion.

2-13

Page 21

ATTRACT [iq] ATTRACT

6(@7}E COLLISION 3 ics vic FROM GES 0 STEERING qe

STEERING A (H4-11)

STEERING B (H4-13)

RATE (E3-8) 1 I

DIRECTION (E3-5)

RIGHT CLOCK (El-11) a

LEFT CLOCK (E1-3) | rc] i

Figure V-A: Steering Decoder Circuit with Sample Waveforms

Page 22

This code differs from the rotation code only when the car is in a skid. The skid condition is determined by Cl (7400). If the car is at quarterspeed or greater when the brake is depressed, or if the car collides with another car, a skid condition exists, and SKID goes low to latch the last rotation into Dl.

The acceleration processor consists of some preprocessing circuitry (D3, 74153) to create acceleration and deceleration pulses, an up/down counter (C2, 74193) to count these pulses and keep track of the speed, anda cir cuit (D2, 7485) that translates this speed information into speed pulses in the GO signal.

With only the gas pedal depressed, the car will accelerate at the rate of one unit per 16 frames (signal from C3-6, 7420 gated with 8F at D3-4). With no pedal depressed or with only the brake depressed, the car will decelerate at the rate of one unit per eight frames. With both gas and brake pedals depressed, the car will decelerate one unit per 16 frames. The up/down counter, C2 (94193) with a fifth stage Al-5 (7407), counts these acceleration units. At speed 14 (binary 11110), C3-8 (7420) gates out any further acceleration pulses and maximum speed is attained. At speed zero, in the attract mode, or after a crash into the pylons, the STOP signal resets the counter outputs to zero. The digital comparator D2 (7485) compares the speed code (SPEED 5-SPEED 1) against frame bits (1F-16F) from Bl (7493) and Al-3 (74107). The result is shown in Figure V-B.

The motion circuit operates on the principle of the Atari patented "slipping counter" method of moving objects on a raster scan display (patent no. 3793483). The motion counters count in parallel with the sync counters on the sync board. In order to move vertically, the vertical motion counter K3 (9316), L3 (9316), and J1-5 (74107) is forced to count short (up) or long (down) with respect to the syne vertical counter. Similarly, the horizontal motion counter H3, J2, H2 (9316s) causes horizontal motion by counting short (left) or long (right) with respect to the sync horizontal counter.

Each frame in which the GO signal is high causes the motion counters to make a unit move in the direction specified by the direction code (D4-D1, RQ). To move faster, GO is high more often. A table of approximate sine/

Page 23

Frame Signals

(STOP)

Signal for all Speeds

(FULL SPEED) iF

2F

4F

SF

16F

wo ODI DAUR WN KR

ll

Figure V-B: GO Signal (Speed Pulses)

2-16

Page 24

cosine values for the 32 different directions is contained in a PROM

(K4, 003187). This motion code goes to the motion counters when GO enables the PROM. The horizontal motion code is gated with VRESET in F3 (7402). This limits the long or short count to one line of the frame. A table of the horizontal and vertical motion codes for all 32 directions, as seen at the load inputs of H3 and K3 (9316s), is given in Table V-C. The horizontal counter is clocked at the system clock rate of 14.318 MHz.

In order to maintain the same amount of motion resolution vertically as well as horizontally, the vertical motion counter is clocked by VCLOCK. This signal is two pulses per line and is gated out during vertical sync so that the vertical motion counter requires one less stage. Using the terminal count outputs of the counters, a car window is formed of 16 clock pulses by 8 lines.

The video processor uses line, column, and rotation information to address video information in a 4K ROM, K2 (003186). Further colum information from the horizontal motion counter is used to multiplex the ROM outputs to a single line from L2 (9312). This video is then clocked into J1-3 (74107) to remove edge effects and race problems. The result is the car video information.

When the car collides with another car, Ll (555) produces a half-second pulse during which the car will skid and spin. If the car crashes into the pylons, a low pulse is made at CRASH (H1-8), 7400). This signal

stops the car and triggers the crunch sound. CRASH SEQ remains low and

prevents further crashes until the car is no longer in contact with the

pylons.

The sounds that are synthesized are the MOTOR SOUND, HORN, CRUNCH (crash), and SCREECH (skid). The MOTOR SOUND is produced by performing a D/A conversion on the speed code (SPEED 5-SPEED 1), and using the result to drive a current source that controls the oscillation frequency of B3 (S55). This frequency is divided by both 6 and 4 and various divisions are mixed. The HORN is a 760-Hz signal gated by the horn button input. CRUNCH is made by gating noise from a noise source (D5-1, 1M324) with a discrete one-shot, triggered by CRASH. The SCREECH sound is formed by an op amp (D5-14, LM324) configured as a free-running multivibrator. This oscillator is also perturbed by the noise source to give it a

Page 25

VERTICAL INPUTS (K3) DCBA a) P= 2) e > a = = =x Za = Zo Oo Na pe a oO = ud a ao oO =z S2 = i «, Se any = aa

COP KK OPK OPK ORK RK OOOF KK Oe RK Orr OrrrO COFRK KK OOOK- KK OOOO OCOCOCORK KK GOOR-KK KO mR OCOCCCCOOR RRR RRR rrr eRe RK RK OODCOOCOrF Perr rr KK RK CODCOD ODOCOOCOCOOCOOCOOR rR eR eee OPP OPK RK OOOR KK ORK Or RK Or KK OOOrKKOrFer Orr K-COC09D0COOOFrRK K-OOORKRK-RK HK OCOOrrr HOO H-SODDDDDDCCODO COR RRR RR RK OOORP Ere Re SSDDDOCDDCDDDD GOOD OOOCOCOF KK COOCOO Or Or Or O- OF OF Or OrOr OF ORF OF ORF OK oF or COr-K- 00K OOK RK OOF RK OOF RK OOF RK OOF KOOrer SCOOOP KKK OOOO RK RK KEK OOOOR RK RK OOOOR Ree ed el el lee hh Nd ed el le ell ed SSSCSCDDDCDCOCDCOCOCOCOOOR RR RR RR RRR eee eRe

1000 0100 STOP CODE

UNIT MOTION CODES INTO MOTION COUNTERS TABLE V-C:

2-18

Page 26

"gritty" quality, and it is turned on and off by the SKID signal F4-8 (7406); the sounds are then mixed, buffered, and fed into a digitally controlled four-position master attenuator. The audio volume trimpot should be adjusted so that with the horn turned on, the signal at D5-8 (LM324) is 0.75 volt peak to peak. Finally, the audio signal is amplified by the LM380 power amp.

2-6. POWER SUPPLY PRINTED CIRCUIT BOARD

The power supply board has the circuitry for the unregulated supplies and for driving the coin mechanism lockout coils.

The unregulated supplies are both full-wave center-tap rectified configurations. The +9V supply may vary from 7.5V to nearly 11V, depending on line voltage at the transformer primary and the load current. It supplies the power for the +5V regulators on the logic PCBs. The +20V supply may vary from 8V to 22V, again depending on line and load conditions. It supplies power for the audio electronics on the car boards and for the lockout coil drivers.

The lockout coil driver should be active when the [On signal is high, i.e., when carn has credit. This turns transistor Qn on, powers the coil of relay Kn, and applies 20V to the lockout coil on coin mechanism n (activating the coil disengages the lockout function). The diode across the relay coil shorts inductive spikes of turn-off. The diode from the emitter of the transistor to ground increases noise immunity by raising the turn-on voltage of the transistor. The 100-ohm resistor from the relay coil to +20V is a current limit resistor to limit the dissipation in the relay and the transistor.

2-7, OPERATOR ADJUSTMENTS AND OPERATING INSTRUCTIONS

  • Adjustments

There are several adjustments available to the operator. These are: a. Master volume switch (sync PCB). b. Game time adjustment (coin control PCB). c. Lockout coil power switch (power supply PCB). The master volume switch adjusts the overall audio volume level to one of four possible levels. It is located on the syne PCB as shown in Figure I-A. Clockwise adjustment decreases volume; counterclockwise

2-19

Page 27

adjustment increases the sound level. All of the car PCBs have their own separate volume controls. These are preset at the factory for balanced output levels and should be changed only by service personnel making repairs or adjustments to the car PCBs.

The game timer potentiometer is located on the coin control PCB in the upper corner near the front of the card rack. It adjusts the length of the game from approximately 75 seconds to nearly three minutes. Game time is increased by turning the pot downward or clockwise as seen from the front of the card rack.

The lockout coin power switch is located near the edge connector of the power supply PCB. If switched to the "off" position, all of the coils will go into the coin lockout mode, and the machine will not accept coins. This feature is useful in applications where an attendant collects payments manually and uses the remote panel to control the game. In order to use the coin mechanisms in the machine, this switch must be in the "on" position and power must be on.

  • Operating instructions

The unattended or automatic mode: after insuring that the machine is properly assembled and secure, apply power by inserting the power plug into a 105-125 VAC, 60-cycle, three-pronged or grounded receptacle rated for at least 5 amperes (600 watts). It will take a few minutes for the TV monitor to warm up. The game should come on in the attract mode (no sound or car motion). A coin in any slot will increment that coin

counter, cause the lockout coil to engage, and reset that car to the starting line. After approximately eight seconds, the game will start (sound will come on and the cars may be driven). All cars that have not received credit will disappear from the TV screen. The eight-second delay allows all players to deposit their money before the game starts. Any player depositing money after the game starts will also get his car reset to the starting line and may play for the remainder of the game. The lockout coil power switch must be on, and the remote panel must be disconnected for this mode of operation.

Page 28

The attended mode or using the remote panel; with power off (power cord disconnected), remove the side access panel. Guide the remote panel cable through the power cord outlet hole and into the machine. Connect the cable to the mating connector coming from the main harness just left of the card rack. If the coin mechanisms are to be used, the lockout coil power switch should be in the "on" position; it should be off if money will be collected manually. Put the access panel back into place. After insuring that the game is properly assembled and secure and that all toggle switches on the remote panel are in the “off" or downward position, apply power of 105-125 VAC, 60 cycles, 5 amperes, third terminal grounded.

If the coin mechanisms are used for money collection, the game will per-

form as in the automatic mode, except that to start the game the start button on the remote panel is used. All toggle switches on the remote panel should be in the "off" position at all times in this mode.

If money is collected manually, the cars for which payment has been received are enabled by toggling the appropriate switches on. Optionally, if all cars are to be enabled, the master switch in the center of the remote panel may be switched on. The game may be stopped at any time by disabling all the cars -- if a restart is desired or if a con~test for a certain number of laps is desired. To start a game after setting the switches to their proper positions, push the "start" button.

2-8. SERVICE AND TROUBLESHOOTING

Indy 800 is sold with spare circuit boards for all boards in the card rack and one spare steering PCB. When inserting circuit boards into the card rack, take the following steps to insure that the game will not be damaged:

  • Be certain that the board is the proper type for that position and that it is not reversed. See Figure T-A for location of board types. Heatsinks should always be at the top of the board and to the right.
  • Be certain that the board is inserted straight into position in the card guides.
Page 29
  • Pushing gently, wobble the board slightly until it begins to seat into the connector. If it does not begin to seat, recheck steps 1 and 2 and check for warpage of the board. Correct any problem.

4, Applying firm, constant pressure, push the board into place until it is seating fully. The front edge of the board should be flush with adjacent circuit boards. DO NOT use fast, jerky motions, as this could damage the backplane board or the edge connector.

When removing boards, always use the card ejector tool provided with the game. Hook the bolt of the tool into the hole in the uppermost corner of the circuit board. Using the frame of the card rack as a pivot, pull gently up to disengage the card from the backplane (see Figure VIII-A). Remove the ejector tool and pull the card out by hand.

When troubleshooting, the short description of each board in Section 1 should be a great help in quickly locating a problem. Replacing the suspect circuit board with a replacement gives quick verification of the source of the problem. To fix a circuit board, refer to the schematic and technical description provided in this manual. Repair of circuit boards should be attempted only by qualified technical personnel with proper equipment. As an additional aid to maintenance, the system has been designed so that all eight car PCBs are interchangeable. Also, removing one car board will only disable that car, without affecting any others.

Page 30
  • CARD GUIDE

CARD RACK RAIL

CARD EJECTOR TOOL

PRINTED CIRCUIT BOARD PULL OUT

GENTLY

HOOK END OF BOLT INTO HOLE

FIGURE VIII-A USE OF THE CARD EJECTOR TOOL

Page 31
  • CUSTOMER SERVICE INFORMATION

3-1. TEST EQUIPMENT

In order to test any Atari PCB, some items such as the logic probe are absolutely essential. Others are desirable and will make the test procedure easier but are not absolutely essential. Some of these instruments are available from the Atari Customer Service

Department and these are: the Kurz-Kasch 520 Logic Probe, the Atari Video Probe and the Hewlett-Packard 10529A Logic Comparator. Other instruments that are very useful are the HP 10526T Logic Pulser and the Tektronix 465 Oscilloscope. These items are available through your local electronics supply house.

3-2. REQUIRED MINIMUM EQUIPMENT

The following items are absolutely essential to perform the test procedures presented in this manual:

  • Logic Probe: The logic probe is an instrument designed for checking the outputs of integrated circuits. The Kurz-Kasch Logic Probe, Model No. LP-520, which is available through the Atari Customer Service Department or most large electronics supply houses, is recommended. This logic probe indicates if a signal is logic high, logic low, or changing from one state to another. Consult the operating instructions included with the probe for further details about its operation.
  • Video Probe: The video probe is a very simple but extremely useful device and consists of two test clips, a length of rubber-coated, test lead wire, and a 4.7K, %-watt carbon resistor. Video probes may be obtained from the Atari Customer Service Department or, if necessary, they can be assembled from standard components available at all electronics supply houses.

3-1

Page 32

3-3. OPTIONAL EQUIPMENT

It is possible to find 90% cf the possible PCB computer malfunctions without the following items. However, if a complete set of troubleshooting equipment is desired, Atari reconmends:

  • Hewlett-Packard 10529A Logic Comparator The Hewlett-Packard 10529A Logic Comparator is used to verify correct IC operation. This device simply clips onto in-circuit ICs and instantly displays any logic state difference between the in-circuit test IC and the reference IC in the comparator. Logic differences for each pin of a 14 or 16 dual in-line package are indicated by a lamp on the comparator. If the logic comparator is purchased from the Atari Customer Service Department, it is shipped with 20 preprogrammed reference PCBs. If the device is purchased elsewhere, these PCBs must be specially programmed.
  • Hewlett-Packard 10526T Logic Pulser The Hewlett-Packard 10526T Logic Pulser is used to stimulate incircuit ICs so that they are driven to their opposite states. This device is available from the Atari Customer Service Department or can be obtained from most large electronics supply houses.
  • Tektronix 465 Oscilloscope The Tektronix 465 Oscilloscope is used for viewing various wave forms and should be ordered from Tektronix. Consult the manufacturer's

operating instructions for details on oscilloscope operation.

3-2

Page 33

3-4. LOGIC TYPES AND FUNCTIONS

TYPE FUNCTION

7400 QUAD 2-INPUT NAND GATE

7402 QUAD 2-INPUT NOR GATE

7404 HEX INVERTER

74S04 HEX INVERTER

7408 QUAD 2-INPUT AND GATE

7410 TRIPLE 3-INPUT NAND GATE

7413 DUAL NAND SCHMITT TRIGGER

7420 DUAL 4-INPUT NAND GATE

7425 DUAL 4-INPUT NOR WITH STROBE

W427 TRIPLE 3-INPUT NOR GATE

7430 SINGLE 8-INPUT NAND GATE

THHS BCD TO 7-SEGMENT DECODER

7450 DUAL AND/OR GATE (INVERTER/EXPANDER)

7474 DUAL D FLIP FLOP

7483 4-BIT FULL ADDER

7486 QUAD EXCLUSIVE OR GATE

7490 DECADE COUNTER

7492 DIVIDE-BY-12 COUNTER

7493 4-BIT BINARY COUNTER

74107 DUAL JK M/S FLIP FLOP

74153 DUAL 4-BIT MULTIPLEXER

74157 QUAD 2-INPUT DATA SELECTOR/MULTIPLEXER

74165 PARALLEL-LOAD 8-BIT SHIFT REGISTER

74192 SYNCHRONOUS DECADE UP/DOWN COUNTER

3-3

Page 34

74193

LM380

NES5S

NES66

RC4136D

MFC6040

8098

8103

8099

9311

9312

9314

9316

9321

9602

74186 SYNCHRONOUS BINARY UP/DOWN COUNTER

AMPLIFIER

TIMER

FUNCTION GENERATOR

DUAL OPERATIONAL AMPLIFIER

QUAD OPERATIONAL AMPLIFIER

VOLTAGE-CONTROLLED OPERATIONAL AMPLIFIER

HYBRID

HYBRID

HYBRID

ONE-OF-SIXTEEN DECODER/DEMULTIPLEXER

8-INPUT MULTIPLEXER

QUAD LATCH

4-BIT BINARY COUNTER

DUAL ONE-OF-FOUR DECODER

DUAL MONOSTABLE MULTIVIBRATOR

ROM

Page 35

Number

003347

000538-02

A000598-xx

000607

A000607

000589

A000589

003153

003182

003170

003184

0030900

003191

003199

003193 SECTION 4.

SCHEMATICS, DRAWINGS AND PARTS LISTS

Title

Assembly Instructions

Parts List, Steering Wheel Assembly Steering Wheel Assembly Parts List, Steering PCB Assembly Steering PCB Assembly Parts List, Foot Pedal Assembly Foot Pedal Assembly

Wire (Harness) Schematic

Schematic

Parts List Syne PCB

Assembly

Schematic

Parts List Score PCB

Assembly

Schematic

Parts List Coin Control PCB

Assembly

Schematic

Parts List Car PCB

Assembly

Schematic

Parts List Power Supply PCB

Assembly

Parts List Assembly Backplane PCB

Schematic

Parts List Remote Control PCB

Assembly

Page 36

NOTE: REMOVE THESE PANELS iN

ASSEMBLY NSTRUCTIONS ASSEMBLY STEP 4.

STEP L MOUNT CABINET TOP A002970

TO CABINET BASE AOO 2967 —

NOTE: BLUE CAR LABEL ON CABINET

TOP ASS‘Y MUST BE PLACED

OVER PC BOARD RACK AREA

IN BASE CABINET ASS'Y

NOTE: SEE DETAIL “B", SHEET 2, FOR MOUNTING ASS‘Y OF CABINET a TOP TO BASE STEP2 INSERT FOUR STEEL LEGS TOP VIEW OF INTO BRACKETS ATTACHED DISPLAY TOP ASS'Y

TO TOP KCTE = EACH STEEL LEG HAS DETAIL HOLES THAT MATCH HOLES. \N BRACKETS ON CABINET TOR SEE DETAIL ‘C* STEP 3. PLACE DISPLAY TOP ONTO | =

STEEL LEQ@S MATCHING HOLES OM THE SHORT LEGS NITH THOSE GN THE LONG STEEL

LEGS.

NOTE SHORT STEEL LEG,1DENTIFIED °

NITRA PIECE OF TAPE MUST BE PLACED ON LONG STEEL LEG DIRECTLY ABOVE POWER SUPPLY BOARD IN CABINET BASE. STEE4 REMOVE COVER AND CWE ABS TOP FANEL FROM DISPLAY TOF ASS'y, TO LOCATED DISPLAY TOF HAF MESS TAAT PASSES THROUGH MARKED STEEL _£G TO CONNECTION IN THE BASE SEE DETAIL “Ar - FEPLACE COVERS AFTER HAkKIESS

'S CONNECTED CAREFULLY LOCATE MOUAITING _ . a

4ARDWARE THROUGH DETAIL { A uy |-———iseusy-tor ASSY A0023969

oa a i ua HOLES IN LEGS. SEE TETAIL "C” AND "D" . MODNTING HARDWARE, DETAIL ‘C* SEMOVE CONTROL FANEL ASS'Y FOR EASY ACCESS STEP@ CONNECT ALL HARNESS BY OPFENING COIA) DOARS FOR ZA a) ( a EASY ACCESS es - CABIVET TOP-TOP ASS

ed

Page 37

bun emo? ALLE DSS.

CONNECT ALL HARNESS BY

OPFENING COIM DOMRS FOR

EASY ACLESS SEE SHEET 2, FOR DETAIL AN ASSY CF STEP 2,4 AND S.

CABINET TOP-TOP ASS'Y

4002970

PG BOARD RACK

| «a BASE-TOP ASSY iS AODO296T

POWER CORD

NOTE: THERE IS AN OPTION HOLE IN BASE OF CABINET FOR > REMOTE CONTROL BOK a LOCATION OF LONG STEEL LEGS. GS TOP VIEW OF TOP ASS'Y

DY Ene WHITE CAR LABEL A | PROD. REL. BLECN 1314 RED CAR LABEL es “ BLUE CAR LABEL

NONE THIS STEEL LE@ ——— CORRESPOWDS WITH SHORT LEG, MARKED WITH TAPE, ATTACHED TO DISPLAY TOP SEC. A.A.

ASSEMBLY INDY 800 WS_/ 3-515)

INSTRUCTIONS.

Page 38

GUSSET SUPPORT-

OUTSIDE FRAME———}- a AN < CLEAT &. ON

N TIE- DOWN BRACKET ASSY

*10-24 WING NUT -ATY 2 "10-24 1f CARRIAGE BOLT-Alv.2 ANGLE IROA! FRAME SERVICE PANEL —— BOOR END VIEW

SIDE ViEW__

DETAIL .B. REFER TO STEP 1 GF ASSY INSTRUCTIONS — SHEET | oF 2

aan DISPLAY TOP- FRAME ASS'Y

_t = —2

TOP VIEW DETAIL -E.

REFER TO STEP 4 OF ASS'Y INSTRUCTIONS ~ SHEET lof 2

DISPLAY TOP HARNESS

SIDE VIEW

/~ MINIATURE CONNECTOR

ra PASSES BETWEEN WALL

OF LEG AND CARRIAGE BOLTS. MERE,

Page 39

TETAIL AL i MER PART WO. CE MRRAA CY SSS BLACK a A | PROD. REL | BEECH 1314

—{|-— suorT STEEL LEG FROM DISPLAY TOP

=) =f) lesan “8d DETAIL .D. CLIN TATLUM* REFER TO STEP 5 OF ASS'Y ol ae veopea_s INSTRUCTIONS - SHEET 10F2 —}-—— LONG STEEL LEG FROM CABINET TOP ASS'Y

Ad

LO *1D-24x2 CARRIAGE BOLTS -QTY 4

*10-24 WING NUT (4) —= "10-2414 (4) ——= CARRIAGE BOLT 4 TOP Vig W pO ART

\— 810-24 WING NUT-ATY. 4

STEEL LEG

DETAIL C__ REFER TO STEP 5S OF ASS'Y i INSTRUCTIONS ~ SHEET 1 oF 2

LONG STEEL LEG WITH DETAIL FOR DISPLAY TOP HARNESS PASS THROUGH SEE NOTE OF STEP3 ON SHEET Lok 2, ASS'Y INSTRUCTIONS.

SIDE VIEW

ASSEMBLY INDY 800

INSTRUCTIONS

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

Innovative leisure ASSEMBLY a YY 800 STEERING WHEEL ASSY

PARTS LIST SPECIFICATION

Drawn Checked | Mech. Eng.

Proj. Eng. Elec, Eng

Part Number DESCRIPTION

000538 002133 090605 000606

72-7512 A000607

75-07 002,

76-042020 76-041010 78-40102 75-S4SN 72-9580 000616 75-055 78-16002 73-120 SRPRRPRPRPRPRP . > Par Steering Wheel Assy (3201-3803) Cover, Kee Ganes Insigna Housing (3201-3545) Shaft (3201-3544)

Screw, Mach, Fils Hd, Phil #-20 x 3/4 lg. Printed Circuit Assy

Washer, Fender, %

Bearing, Thompson (20L20-F) Bearing, Thompson (10L10-F) Steering, Wheel 10" Nut, #5-20, Nylon Lock Screw, Mach, Truss Hd, Slotted i#s-20 x 5 Lg. Hub Light Washer, %" Int. Tooth, Starlock Silicone Grease, Compound #5 MACH SCR ISTE V VY, Paw tO Pe.

Page 42

wores: APEUY UGHT FILM OF SIUCOKE REALE 95 COURDULD (08 EGU.) OU AREAS IWRKATED. (ITEM (8)

VENDOR FRET NO. 3201-3605

Page 43

vie ak vane inte Our

Ry [ReERSED FOR PES Fron B feevsco RN bane C [RNSES PER Ea) BO 4-4u ee 1 [eevee Fee Be BS aan | E [REVISED PER ECN 379 © 51774 Fouao/|porr F lpevisem Fee Gay Se jorlein fp) D @ &CN 1ST 2S WS

NOTE: OLOS3B-01 - AS SHOWN O000598-02 -OMIT PART N° 78-4010! ADD 78-40102 “OMIT " "000599 ADD 202/53 _

ical ast commen mere |e Uostine tates50 ° Te coe gL ATARI A

Sore ASSEMBLY’. STEERING WHEEL FOEEDTT [aby Bas] SEE PL COOSSR —= SED Taree DPD) ACOOSIB-Xx <0 Tam ey

3 { 2 | \L

Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 45

Job Title paceTRAK STEERING PCB ASSY Dwe-P/L 000607 arb Lisl Specification sheet 1 of 1 Drawn Checked Mech, Eng. Rev. ATARI Proj. Eng lElec. Eng.

Vv Rev. Description Description

Redesigned 5-6-74." Rev_per ECN 397 5/28/74 7/:, Rev per ECN'457 6/3/74 Rev per ECN 601 7/15/74% Rev_per ECN 1531 ‘ =e /C}A lc, |=

[item Part, No. Qty. Description

1ooos14 =| 1Printed Cifcuit Board (E)
20010921Light Mount
3001151RefSchematic Diagram
411750/10-57502Resistor, Comp., 75 ohm, % watt, 5%
511471/10- 54714Resistor, Comp, 470 ohm, % watt, 5%
611332/10-53322Resistor, Comp, 3.3Kohm, % watt, 5%
734104 /27-101103 | 2Capacitor,| Ceramic, .Oluf
870006/38-2NS7772Transigtor|, 2N 5777 (Photo Darlington)
970000/34-2N36432Transigtor|, 2N 3643
1071008 / 38-ME71242Light Kmitting Diode, I.R. ME 7124

12 1 13 |

1480089 /79-58005Connector,| 10 pin, PC Mount, Amp #1-380991
1572-12128|Screw, |Madhine, Pan Head Phil, #2-56 x 3/4 Lg.
te | 75-042boaWadher salit Lock #2
1775-91281Nut, Hex, #2-56
180037491Retainer, Led Light Mount
Page 46

aye 4 oA Q7

Roe laa K Q2 O

= MODIF.

REFER TO SCHEMATIC OCliE!

NOTICE TO ALL PERSONS RECEIVING THIS DR YING CONFIDENTIAL: Reproduction Forbidden without the spe tific written permission of Atart Ine. Los Gatos. California, ‘This drawing "s only conditionally issued, and neither receipt Thor possession thereo! confers or transfers aay Fight in, or Ticense to use. the subject matter of the drawing or any design ‘oF technical information shown thereon, tor any. right to fe produce this drawing or any part «hereof. except for manufac fre by vendor for Ata incorporated an8 or manufac Under the corporation's written ficense. no right (o reproduce this drawing & Branted oF the subject matter thereof une. ht ‘written agreement with or writen permission from the cf poration NEXT ASSY

APPLICATION

Page 47

REVISIONS

INITIALS ond DATE DESCRIPTION PRET. cheCK | LNG RG 53-14 REV. PER ECN 397

REV. PER ECN 457

L |ReV FER Ec) Gol

M {REV PER ECN 1S31

MODIFICATIONS | FOR OOOGI4 REV J P.C. BOARDS \, JUMPER £20M PIN 2 TO PIN JO OF THE 10 PIN CONNECTOR, ON CiBeDIT S\SE OF BOALL,

  • JUMPER FROM PIN 1 OF THE 1D PIN CONNECTOR To THE PAD MARKED +5V (END OF BI) ON Cle@cuIT TIDE OF BOARD,

MODIFICATIONS | FOR OODSeI4 REV K P.C.BOACDS. ), DOMPER FEOM PIN Z TO PIN 1O OF THE JO PIN CONNECTOR, ON CIBCUIT Sibe OF BOARH.

ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ON: FRACTIONS = #1/16 4 = #41 ANGLES = #19 ASSEMBLY STEERILG BOARD

DRAWING NO B | AOOOGO7 sour Qe] [om 1 SED ON

APPLICATION

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

po | Sob Titl Dweg. on e*°° OOT PEDAL ASSY *E-P/L 000589

Sark Fist Specification sheet lof 1 | Drawn Patty Checked Mech, Eng. Rev. Elec. Eng. Proj. Eng,

Rev. Description —_—_—s|_ Apprv. [Rev. Description A _|Release for Productiomwoshe _

  • Vos] | rev. PER EON 969 B Revise per ECN ' ~21-74 Cc Rev per ECN 229 4-4-74 _D__|Rev_ per ECN 382 [5-20-74 E Rev per ECN 442 5/28/74 4: *, F Rev per ECN 460 6-6-74. | Item Part. No. lQty. _ Description

1 A000589 |Ref |Foot Pedafl Assy (3201-3555)

2000590 | 1oot Pedal (3201-3533)
3000591 | 1edpl Foot (3201-3534)
4000592 | 1priing| (3201-3550)
5000593 | 1umper) (3201-3551)
6000594 | 1top Washer (3201-3552)
8000597 | 1Bearing Block (3201-3549)

10 , 11 {75199/72-15085 | 1 Serpw,|mach., Pan Hd, Phil #%4-20 x 4 lg 13 oo 14 |75-7002/75409 1 Washer, Fender

178326% A/RSillicone Grease Compound #5

Contact C ement

Page 50

NOTES +

  • TAK TEM S70 Te Swe BRST ADUESIVE. Ze BS APEC L6UT SMEAR SKICONE COMPOUND (OR EGLIV.) OU AREAS KDKATER.( ITEM 16)
Page 51

C2977 | way aco en 9152 A 3351 ‘ated i sere, Ten

4 | 3 SRE WL TBARS ova swscaraos — K | RELEASED FOE PSD Bad 8 [PrR BON Sa C [revises RR ED ees Esa lRe yoy, D [REVISED PER ECN 382 F [52074 7 E [REVISED PER ECN 442 Rl saealge: F [REVISED PER ECN 460 TF|e-<-74/ 375° lesa

i ATARI

“Asse | cee MBLY PETAL Re ge RB

Page 52

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 53

ATABL INCORPORATED

2|1
Ve) LYS Bgscreenae

ESET B/E/S/4/S/E 8/8 Rae, on TO as

S|TIULVIWIX FY |Zia er Pee EONeIE TT1reee
-COIN MECH:F
8Hiae tas 2aera2ODE_N4eo!
2s as 8 35 |éiD
_—= rHCOIN.
= ——_—_“F 7¥ 7Counters
=HqYs
=== ——*1 6
7WN 5—
=]==ats |
1~-
.4+SS== FElen
ole lelebrag dic, duo, ono|
asHORNVN+od

. so a oer

  • oe 7? & 5 ORT TW.PR. 6 PLACES, 2| Come _syxc_ | C ae {3[umMPER __|
iaTCH4 | YELLOW CAR

v “{5lrewore f 6 ATE WHT CAR ale Buy TREwore 2 S16 [8] GYAN CAR

4Z || 3LEY o[REMeTeE 3

A HO] GREEN CAR dy

=Li mek ylnewore*
,} 3 q12] + 5v_
—wtIGMfBK|)3| REMOTE 5

| _——falpuce—c

fg} 3 5Onlan|js|aEWCTE —B
eeom6} BLUE CAR 7

i>—g9-——— vise oxpllt 79| REMOTE 6

TTay—letreo cae|B
"RB| ?21| START Sw.

ols ae

=2 g———=
ifs 3]al; ||E
m7&
13INeOC! DIODE&

EAVEZ

| fe! S TV Power 3 FANS Fe3a GLb)

.wifea
awheK1

aaa ATARI ™ INDY— 800 WIRE ~ SCHEMATIC Losuon Canna 85030 ]

{

Page 54

14.218 MAE

rebet yr r e a

oTuee cars 7

farjoteen aes 6

vinéie ARLE ee Re P85 | .,, [8 rye ana ca ap pvmranevs 80: afb

3Hoel Ke,|
Zceee (28)S.

yee

2S 0 i 2 LL 23 em Far e ra vy oie

eo

me

SHresev
sovoc}=Tafbesper Te eeaeo

32 250 > Ce-c10 By i)

mone4ene

yo ened

[1] Lae [+] % a] «sv to

nN¥wee TH ee

ano veo '[b] Steer

2Tewve

Res ox 10.

CAR 1/25}caetAr 6ge

ais 2s Pe es, Se he Bass 2)e Tecan,

TART [ea]Hee6.

+Sv

ee tox

fe=gaee ary:
oeaes=z
Bat.ne

en HEN SES

Toeloo?ale

ara [x cea +B0

10K ears [wh —p- TRESS

veTS7
ear SeATTJ
roKoo.[se

CBRE | 19) = CRS

ee | est

Zae7 [ea]eT4

av pe ceo ewe

ues!

Scoee ee ser|Y }-—

MAC TER ALLO NOLUME

wv wearer! fon

‘ SWITCH

ee eS aes cre, sae os mo $ IAnere wae 2

svaTEx cua 4

And

Page 55

Pers b* Ea PZ 7 pases TL Phehs | tk

T

Page 56

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 57

A ATARI Innovative leisure Drawn Checked Mech. Eng.

Elec, Eng Proj. Eng. PARTS LIST SPECIFICATION

1 003183 2 37-LM309 3 78-06004 4 72-161058 5 75-916S

7 75-056 8 66-O71P4T

9 73-802 10 37-7400 11 37-7402 12 37-74HO4 13 37-7410 14 37-7417 15 37-7420 16 37-7427 17 37-7437 18 37-7474 19 37-7486 20 37-7490 21 37-7493 22 37-74107 23 37-74153 24 37-9316 25 003188 26 003189 27 90-101 28 10-5331 29 10-5681 30 10-5102 31 10-5103 3 28-101331 33 27-101104 34 29-011 35 24-060257 36 | 31-7404 BT | 79-428HiG BE

PANN MDPOYRPNEPERRP WENNER EB ENNNEBRE OH RTS SYNC BOARD P/Lo03182

Page _1 of 1

DESCRIPTION

Printed Circuit Board LM309K Positive 5-Volt Regulator Heatsink, Wakefield 680-.75A Screw, Mach, Nut, Machine, Hex, 6-32

Lock Washer, Internal Star, #6 Rotary Switch, P.C. Mount, #71AF36-01-1-04-N Switch Knob (Raytheon #50-5-1) 7400 Integrated Circuit

7402""
74HO4"Md
7410"a
7417"a
7420""
TH277Ly
74377i
7474""
7486""
7490"tt
7493""
74107"“
7TH153""
9316""

P-ROM, RT8 Check Points, 32 x P-ROM, RT8 Racetrack, 256 x 4, 14.318MHZ Crystal >» Pn Hd, Phil, 6-32 x 5/8"

1P-4T, Grayhill

8, 256 Bit 1024 Bit

Resistor, Resistor, Resistor, Resistor, Carbon, Carbon, Carbon, Carbon, 5%, xW, 330 ohm %, %W, 680 ohm %, %W, 1K ohm 5%, &W, 10K ohm Capacitor, Mica, 330pf, 100V Capacitor, Capacitor, Capacitor, Ceramic, Monolythic, Electrolytic, O.luf, 100V .22uf, 12V 250uf, 6V TAOA INTEGRATED CIRCUIT SOCKET, 1.0. , Ie PIN

Page 58

250 at » 2 Cv o a m 19 us uv s

oS os7tr

wy =_ ra) =z” mz 45 Is vas

~~ Fo.°8

ea ig: 5 ag b _ < +9 ~ a a

Crooneee:
533.749034 7400q

ae papegeayo getaaes a

oud6 :.
view oeeotacoocote’
=ho al g SPARE . H3 7427 j H4‘

ppepececeds ue : ° 3 i 4) ra 8 3 ifocecote oprectoee ri r 2 | F2 74153 4 Fa 003189 a 7 4 i [eotoeseatoy: UOC: Fy 2 los fe hal , i

abeoeOegoee !He
w€2 7404 @l|f 274107\ }
q||ipetcegeTHep |
co<7cs {{

{I

OtOtOt

ve eee’ a 1 iG F ‘ \ i! ° OU | .

oO(} C2 7437<3 7474,i

i eoegte 1 ) : olpecdieegs

a2B83 7400o

ide aie de AG S316 ob t iM ae Re O[230'0 Gye)

Page 59

Daa raiaalel weer: ae:

Sinead

Teed aS

etiogs: — 4 FS 7400 _—_ geeers -_ —_—

goedite ——_ ES 003) pene verecyes ° esome (10 ° : ome ooeten — DS 7417 _—_—r gogege ne

,

= ted Mores: LOINSTALL ITEM 27 (IG PIN LG. SOCKET) IN POSITIONS Fa AND ES. z ‘ois Fer eon 20

ra, EMBLY LEAWING To BE OLED WITH OOZIBS REV EB P.C.Bd.

IsconPoR a ee |

"ASSEMBLY, SYNC BOARD Reed

ee.

Page 60

ces

+ey

Are

sew

Re toe,

fea’ score RESET

$— scone cesar ro Ase lace me ye

Bos tr &

5A GA 7A 4b BA 34 28 tA je le Ja ep pels

Sa 2210

Lé. 4 ot Teh kh tele

Pe =a Acre, Es) 33) ee Bee 2B fe | lel Je |e am 2F 4D ab ar

po ogee vest

PA, ES epee =| Te ee we lela oF eb Ge oF

25eH

wey

ev

$ tcoze weveT

Te BASES L | Lu 1 i WIEN T 2 BY AY 2v OH Bn

Page 61

J} & o

aremee

Lester 1625 Leave 1LZ leaner tpt No LEALEM Dee Awe,

E3| PEOUICTION BELEASE Bevices Pee EON eT

REVISED Pee ECU IBS. PolojT

“By TO Ty,

vied 3 PY (unre)

vines 4 | '3} @ccey Vives 2

mezfiiS
|eee a(ees)

s

—oeyiono 4

od

,Zane3UL] feven)

« Lie io _pEyvinee © G6 se EES eee

—Hiviveoe

Bee Q JUMMES. POLIT ON: (vecow)

MONE @lace sceeens wivee 7

©-1Dor parreeny(Puce)
o-2ware sceeen,vino &
0-3NoeMaLGacenra)

+ SV TO BORRD.

[ees @Nb TO BOAed

I oT st 2V eH BH oH AARE INCORPOR ATED,

mw SCHEMATIC

ZCORE P.C. BOAKD

OO3I7TO fe

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

RT8 SCORE BOARD 9.93179

Page 1 of 1 ASSEMBLY TITLE

PARTS LIST SPECIFICATION

Drawn Checked Mech. Eng.

REV.

—-+ Rev per ECN 1142” __ Elec. Eng Innovative leisure

DESCRIPTION

1 003171 Printed Circuit Board 2 37-LM309 LM309K Positive 5-Volt Regulator 3 78-06005 Heatsink, Wakefield 680-1.0A 4 72-1412S Screw, Mach., Sheetmetal, Pan Hd, Phil,6-32 x |5/ § 75-9168 Nut, Machine, Hex, 6-32

7 75-056 Lock Washer, Internal Star, #6

10 37-7400 1 |7400 Integrated Circuit 11 37-7402 3 17402

12 37-74042 |74047"
13 37-74082 174087:
14 37-74101 = |7410:"
15 37-74321 17432"7
16 37-74481 17448"7
17 37-74853 17485""
18 37-74908 17490""
19 37-74934 17493""
20 37-741534 174152"7
21 37-741741 |74174""
22 37-741751 74175""
23 37-93011 19301""
24 37-931217 19312a:
25 37-93221 49322""

26 10-5102 2 |Resistor, Carbon, 5%, kW, 1K ohm 27 10-5103 10 |Resistor, Carbon, 5%, %W, 10K ohm

29 28-101331 1 |Capacitor, Mica, 330pf, 100V 30 27-101104 € |Capacitor, Ceramic, 0.1luf, 100V 31 29-011 1 |Capacitor, Monolythic, .22:f, 12V 32 24-060257 1 |Capacitor, Electrolytic, 250xnf, 6V

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 65

Dimevisen ree ccu ee [hr | el Revises Pex ecu oar Veh

NOTE > I. THIS ASSEMBLY BDEAWING TO BE USED WITH COBITI REVISION B P.c.BO.

MODIFICATIONS:

  • GUT TRACE THAT GOES To “O” PAD IN UPPER LEFT CORNEe OF BORED. 2.JUMPER "O" PAD TO LARGE GROUND TRACE. B.dUMPER “B" PAD TO LARGE GROUND TRACE,

= g a & g

i—

ap TAN nconronars0 Toscote ear 080 A TAR! a ™ ASSEMBLY, a SCORE BOARD

nab RABIN: SU ip | AdO3170 ar BAI see P/L OOBITO aaa ee xe Me

Page 66

ns con 1 sw

aor

nm con 2 sw.

eer

q coma Sw

{31| Tos

1, con 4 aw

ee reloee 2p tox eek fiel=oe

sey aTT@acr S eas 220K

Rae 220K

ee bal 2S

e een il |e Rae PLAY TIME, sv

ie Vee

or

exe, sss |p spi 2] ut Beet

  • Tece0 Jou

av a ic

ees oe

pray irae S150

lceenrt 2 cgeorr 2

—* up 4 svaet ec Pap. iH 8 7B czepit 2. event 4 eeenir 2

staat

a Ayer REIT F222 pst €2 0 cs

ExS 3, acto eji0. i ENS GIVE. zee 4ev Ww

Page 67
  • 3 B |PeobucTiON RELEASE. Pees | awe |E C | REevISEO PER ECN 1387 “ths |e cae D [Reisen PER Een 434 fast [Sais | IO [E Resert = [REVISED PER ECN AGS (6/9/75) (I~ Ke

cae reser 2

cae veser 2

ene eecer a

END Game. Zee [w +8y

ou can 4 C30 +Sv Reset S

ese , a my 2 the Je | ape ake Bet wer aah le

Bcoee Sicapagd LAST REF. DESIGNATIONS Pasi : geser +o atid ess

<42 ‘: bess eee 1 FS 2 az eee eB [24

cae ey eecer 7

ese vow

carele “

cae. =n Game. eerey @

Nore: TALL DIODES AGE INDIE.

to Boas cae wee wane Ey 7 Bones

= ; ler seer | RES oat Catena 5080

SURE rile eee he ™ SCHEMATIC ,

COIN CONTROL BOAZD

Page 68

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 69

ASSEMBLY TITLE

PARTS LIST a ST SCALLION Page 1 of 1 lpDrawn ss —~—idY Checked Mech, Eng. Proj. Eng. Elec. Eng Innovative leisure

Printed Circuit Board 0038185

237-LM309LM309K Positive 5-Volt Regulator
378-06004Heatsink, WakeField 680-.75A
47214128Screw, Machine,Pan Hd., Phil., 6-32 x 5/8"
5758-916SNut, Machine, Hex, 6-32
775-0562Lock Washer, Internal Star, #6
837-740047400 I.C.
937-740237402 ~«"
1037-740487404 "
1137-740847408 ="
1237-741017410 ="
1337-743017430 = ("
1437-747457474 ="
1537-749327493 °°"
1637-74164174164 "
1737-932219322 "
1837-5551555 Timer I.C.
1937-LM3392LM339 Quad Comparator
2034-2N35652Transistor, NPN, Type 2N3565
2131-1N91427Diode, Type 1N914
2310-51018Resistor, Carbon, 3%» “ly 190 ohm
2410-510251K7
2510-510324""mom TOK"
2710-51048"7wo" 100K "
210-52243":wom 220K
2910-52211""moon 2a ow
3010-52748w"W " 270K "
3119-3111051Trimpot, 1M ohm, P.C. Vert. Mount
3227-1011021Capacitor, Ceramic, .001 uf, 100V
3327-10110429*"0.1 uf, 100V
3429-0112Capacitor, Monolythic, .22 uf, 12V, kad.
3524-2501051 Capacitor Electrolytic, luf, 25V
3624-0602571250 uf, 6V
3727-1201048Capacitor, Ceramic, 0.1 uf, 120, 20%
3833-2N36441Transistor, PNP, 2N3644
10-53942Resistor, Carbon, 5%, %W, 390K ohm
Page 70

PAT NO 3793483 ATARIO©7TS

MADE

1N usa

Page 71

¢ [eevises pee cou 1367 [fs TS [doe HANG FEL ERI ISZS | Si ROGER BAT To DRAWING hs > [oewoee, vee con 1a34/iaa7 lal REVISED PER ECN 1405 YR

NOTES: I THIS ASSEMBLY BEAWING TO BE USED WITH COSIBE REVINON B PLC. Romeo. 2, ALL DIODES ABE INGIC.

MOBIFICATIONS: (TO BE DONE To COBIES REV "a! P.c. Bonen) 1 ON Cigcort SIDE CUT TEACe BETWEEN PINS & ANOS OF CS, AND COT L-SHAPED TRACE GOING To PIN & OF CSAS SHOWR:

cor BETWEEN BES

cs agagae0 CIRCUIT SIDE SHOWN

ATARI INCORPORATED c00 Winchester Beales START oes

™ LSSEMBLY, COIN CONTROL BOARD crm

cee PA comies

Page 72

TER Reeet

ATTRACTIIS)@3+N

<a, (EE couusiow Se sbae

0 tl es560 teue Aneeen
seme! Ofnah easiqth
oesTt.
7AG—a

° t We Zam RESET a oY Ja been Y lets tele bu is | 252 4 Wey us[A Be Stole sla eee

(30Eeiv gg Teo co eS

3c Male rer pico 25 reopB sco 193

en YT teze7.
wyiaya ep a} aT4elke

cer

xt | SRS“Boteer HB re
ream 1, aitaeke+Ey
ereeninelom(Sapa 2
ED,lelSapa
64p3
<t] aco ct ct 63

eB pele 7S

onefeeTe seare

ee [et voy |

Burien 2400|euace

br 02 03 o8 eas aus

Is Jo Jo Be = st. ‘a0 we it tours f— —

4 sects tp? veo cx [5] pt she cae eeeer[i BSB motor seeavency avrexct a lo 17 Me are, con get RU Be filce 8% MoroR

towae <[~ @ OeN

@) PST | Ria BOK Ae ay [> ia oo:

42(veces
2214, a a2B

Pn na Ba S dere 30 | 25° a vere cer] napster k ese eee wee se

caiTs=
a8 atlLe7

sv T ca TERS

eu sey i mulls... J ZuION

+20v,CRASH SEQT2alTERE

ct 1c je. aE

a-TReserSa)ce
2a, | BSSigie

UMBAOT- 15 ep 27

®me gecanisLF sala
L20lc

7 eat co St Sez

fee]Af2

ome ot CARS.

Page 73

sv

A | PRODUCTION RELEASEthe |ea

B([ReVisED PER EW IGG [verse le Z [Revised PER EN 1248, 209 [hs B=

D [PeviseD PER ECW ISS!siahs LiTe

© [Revseb PER EO) 1478 he OTK | Dy + ms

—eat

aon a, aH de le Is le J a lel

aa2a
cer WeSswiser

eet esre | Te ake 2a

Ga ap ac a MeGas acap meoa ae ac ap vel
va) Bp 2)7uray rey TayPrac a
boae+cou
cae RESET.eebu fre bs
crockice WOWea

v

ZTE 20,"
aae}4© 32 [8

wie 3

+iea{e 4/4

fe is rs

tTol el.Wezef
fTple7Cc
5 lols2 [4 [s |e [>r7
3 PEacer$2]2 o}& 4} raecy | Sie ure
cs2“se
10Me[ae o8 ac 00 meMe ae4cae, 2 hpS fia] RE
Tal1aTAH2 @P caeFeTo MOTHER?
evoce|} —$Bac ichBoaeo
neywr sera, ae cee

Bod

Jeecee
=2eseAuDIO+20
axB S|moToRVOLUME,Wdwhe
oncntae& HoeN1400i

aTTRACT co a MoToOR as. Bd sHoeN 2 4 8 C10 ae (uM = Hig] Audio out

ON TroeEAR.B00B

BP liguive’ GOO 003629 (cevecren 2uBee}

vou. 2

ATTRACT

SORE ine Be Se

SmaySitato

EC re a Stes oS ATARI“ ATARI INCORPORATED ate Winter Bevan

SCHEMATIC CAR BOARD

Page 74

ASSEMBLY TITLE f ppg CAR BOARD /L 003000

PARTS LIST SPECIFICATION Page _1 of 2 A ¢ ella Mech. Eng. Elec. Eng

Part Number DESCRIPTION

1 002999 Printed Circuit Board 2 78-06004 Heatsink, Wakefield #680-.75A 3 37-LM309 LM309K Positive 5-Volt Regulator 4 37-LM340T-15 LM340T-15 Positive 15-Volt Regulator 5 37-7400 7400 Integrated Circuit

6 37-74027402""
7 37-74047404""
8 37-74067406v.
9 37-74107410"

10 37-7414 11 37-7420 12 37-7474 13 37-7475 14 37-7485 15 37-7490 16 37-7492 17 37-7493 18 37-74107 19 37-74153 20 37-74193 21 003186 22 003187 23 37-9312 24 37-9316 25 37-555 26 37-LM324 27 37-LM380 28 34-2N3565 29 003629 30 35-2N3644 31 31-1N914 32 38-MV 5013 33 79-42424 34 79-42116 35 19-311103 36 10-5151

7414""
7420""
74.74"u
7475"t
7485""
74.90":
7492":
74937:
74107"x
74153""
74193*um

ROM, RT8 Car Video, 512 x 8, 4096 Bit P-ROM, RT8 Motion Code, 32 x 8, 256 Bit 9312 Integrated Circuit

9316""

555 Timer Integrated Circuit LM324 Quad Op Amp LM380 Audio Power Amp Transistor, NPN, Type 2N3565 Transistor, Noise Source, 2N3643 Transistor, PNP, Type 2N3644 Diode, Type 1N914 Light Emitting Diode, Visible, Red 24 pin Solder Socket 16 pin Solder Socket 10K ohm Trimpot Resistor, Carbon, 5%, %W, 150 chm "

37 10-5102"" " iK ohm
38 10-5152"". ” 1.5K ohm
39 10-53327”" " 3.3K ohm

DREPYNPERPN OPP ERE NOPE EWEN EBB EEN PE PEON ER EEE

10-5472 4.7K ohm

Page 75

ASSEMBLY TITLE RTS CAR BOARD P/L 003000 PARTS LIST SPECIFICATION REN OE ‘| Page 2 of 2 DESCRIPTION

10-5103 Resistor, Carbon, 5%, %W, 10Kkohm 10-5123 " " " " 12K ohm 10-5153 15K ohm 10-5333 33K ohm 10-5683 68K ohm 10-5823 82K ohm 10-5104 100K ohm 10-5224 220K ohn 10-5474 470K ohm 10-5105 1M ohm 10-5225 2.2M ohm 10-5475 4.7M ohm 19-311254 28-101101 27-101103 21-250103 27-101104 21-250104 29-011 24-250105 24-250505 24-250106 24-250507 72-14128 75-916S 250K ohm Trimpot Capacitor, Mica, 100pf, 100V Ceramic, .Oluf, 100V Film (Mylar), .Oluf, 25V Ceramic, O.luf, 100V Film (Mylar), 0.luf,25V Monolythic, 0.22uf, 12V Electrolytic, luf, 25V Electrolytic, 5uf, 25V Electrolytic, lOuf, 25V Electrolytic, 500uf, 25V Screw, Mach, Sht Mtl, Pn Hd, Phil, 6-32 x 5/8" Nut, Machine, Hex, 6-32 NNFPENPNPMFPERBPRPRERPNNNNYEFRPRPEPE ©

75-056 Lock Washer, Internal Star, #6 ZI-INS OO 2 PHODE | NATIT:

Page 76

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 77

Revises ree cen rear [ir le Revisep pee en 14268 Phe]

OQ ass NO. £O03008

CAR RGART

NOTES: I, LED'S TO BE MOUNTED POINTING TOWARDS RACK OF BOARD AND LAYING GOWN.

  • THIS ASSEMBLY TO BE USED WITH C0798 REVISION 'B" Pc ROALD

MODIFICATIONS | (TO REVISION H AND ZEVISION Cc’ 002999 BOARS). LINSTALL TWO IN4QO! DIODES IN SERIES AS SHOWN, CUTTING TRACE UNDERNEATH EACH BIODE,

  • INSTALL IOuf 25V CAPACITOR AS SHOWN STANDING UP.

MOBIFICATION , (To REVISION "B COZDSS BOACDS ONLY) B.CUT TRACE AS INDICATED. JUMPER + (POSITIVEJEND OF 17 (iouf /2Bv) CAPACITOR TO DS PIN 2 (CLMBZ4).

ATARI INCORPORATED Trans omtawar erie "GROD Wine Boleros Stannssa 1 SCH Ueetaton Calon 98030

™ ASSEMBLY, sent gen mo ono CAR BOARD

AOQOBOCO |'E

Page 78

com wewour cow

Ba Be com 2 a % becnaur cote ere

Ro Oe cone Wa——fa] enoor ore cone ro an | 28 a [lo ou pa

co eSear

} wus,

Ae con 4

  • tockour re
Page 79

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 80

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 81

A. ATARI Innovative leisure f ASSEMBLY

PARTS LIST SPECIFICATION Page 1 of 1 J inDY 800 LEZ POWER SUPPLY P.C.B. P/L 002191

Drawn

Checked | Mech. Eng. Proj. Eng. Eng

Part Number DESCRIPTION

L 003192 2 24-160808 3 24-250508 4 31-MR501 5 31-1N1199A 6 78-06006 7 61-011C 8 10-5472 9 13-0100 10 34—2N3643

12 34-BD437 13 72-1405C 14 75-914S 15 75-054 16 75-0148 17 79-58008 18 79-3202

19 46-2031503 20 46-203401 21 ~ = DOOPRPNNE OE P.C.B., Indy 800 Power Supply Capacitor, Electrolytic, 8000uf, 16V, 85°C Capacitor, Electrolytic, 5000uf, 25V, 85 C Diode, Type MR501 (3A) Diode, Type 1N1199A (12A) Heatsink, Wakefield 680-1.25 SPDT Toggle Switch, C & K 7101 Resistor, Carbon, 5%, WW, 4.7K ohn Resistor, Carbon, 10%, 2W, 10 ohm NPN Transistor, Type 2N3643

NPN Power Transistor, Type BD 437 (SGS-ATES) Machine Screw, 4-40 x 5/16, Stainless Hex Nut, 4-40 Lock Washer, Internal Star, #4 Flat Washer, #4 Connector, 10 pin, P.C. Mount, Amp #1-380991 Fuse Clip, 3AG, Beryllium Copper, Silver Plate, Little Fuse #121001 Fuse, 3AG, 15A, 32V, Fast-Blow Fuse, 3AG, 4A, 125V, Fast-Blow 22 AWG Wire Jumper

Page 82

eae wiee —— 2PLACES,

3>o
cseea<B

eocat | | scoous | | sooo. | | sooomF

levsyay25N
Page 83

Mop. 1 i | & Pusces

4 PLACES,

Potton tad Stas erin ed a ta, Djeenes rrea ses [Fhe | s & [Revisen Pee cov ieoe gaze [Sake | | F [REVISED PER FON 1458, \a@m BOE py

[ST 600 |

NOTE: MOUNT CRN OND C2I2 (MRSOL) VECTICALLY, WITA CATHODE SIDE DOWN, REMOVE PINS AND & FEOM JIB BEFORE MOUNTING REMOVE PINS 1 AND 2 FROM VIS BEFORE MOUNTING REMOVE PINS 2 AKD IO FROM JiG BEFORE. MOUNTING. Pune

MODIFICATIONS: (TO COZ192 REVISION "D” BoazDS ONLY) 1 SOLDER THE COLLECTOR LEADS OF THE EIGHT 2N3GOS TRANSISTORS TO THE LARGE COPPER APEA AS SHOWN.

Tats orarene wHGTED ATARI INCORPORATED. 100 inter Brean

SERTACE Frise Shao 0 ™ ASSEMBLY, POWER SUPPLY BOARD

See P/L COBB

Page 84

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 85

Innovative leisure ASSEMBLY, TITLE RT8 BACKPLANE BOARD

PARTS LIST SPECIFICATION P/

Page 1 of 3 003199

Drawn Checked Mech. Eng.

Elec. Eng

903200 79-514222 79-S14243 75-1408 75-914 75-054 13-Silool DESCRIPTION

Printed Circuit Board 44 Pin Edge Connector, 86 Pin Edge Connector, Screw, Mach., Pan Hd., Nut, Machine, Hex, 4-4 Lock Washer, Internal CoNNECTOR KEY (Backplane) 156, Dip Solider -156, Dip Solder Phil., 4-40 x %"

Star, #4

Page 86

s6n00¥ vy] akw ti sowe 81d enbesis OM La FoR Suww ag | BLY

Page 87

-yoTe 3 Rev. @ ones ONLY

D2 news PRODUCTION RELEASE ihs; Le 17 [Revises Pee ecu i2sa_ [Peers | Br be pevisen Pee en aoe [*Bhs [ae [K Revises PEL EG 8G [ehs] TOE

NOTE

1, ALL CONNECTORS MUST BE HAND SOLDERED TO Pc. BOKeD.

  • APPLY DENNISON #43-i4@-1 OM ALL REVISION "A CORED PC. BOARDS (COMSOLENT =1DE), B.APPLY DENNISON 43 -14G-1 SIGNAL BOT TO THE ORE PLACE NDICATED, ON ALL RENIDION "E” 003200 PC. BOARDS (COMPONENT SIDE).
  • ADD A CONNECTOR KEY TO CONN. JS (Sync 80) eeTWwEEN PINS BI & 32,
  • ADD A CONNECTOR KEY TO CONN. VIO (<CORE 2b) BETNEEN BINS 29 € 30. C.ADS A CONNECTOR. KEY TO CONM. 311 (COIN BO) BETWEEN PINS BB E34.

MODIFICATIONS S (TO REMIION "A 002200 F.C ROARS OULY)

  • BUMPER CONNEZTOR UD PIN Y TO CONNECTOR WiC BIN 3B,

ATARI ASSEMBLY, BACK PLANE BD.

ie nN AOoz1S9 |d RiewaL BOTS TO THE TWO PLACES INDICATED,

Page 88

oN

OFF

on fs o a . OFF

re=ec3

O- Ey

OFF

4oNReq

jes 10)

‘OFF

reoNees

ps 7 OFF

toNeco

fal | ms OFF

tonec?

2D Ss

OFF

rsonece

ON-NONE- ON TOGGLE (7 PLACES) OFF D ore ane REMOTE COM, START ON ° = celta oe NO TF MOMGNTARY, cae cans) rUsW BUTTON GNO

hy vendor for tas ett corpora NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Repraduc ‘he rien permit Inceiter'ox [

Forbidden without the Calton

in ne }— ASOSISS [et-S Paver

APPLICATION BLL

RED

WHT /2Lk

G@en/ek

OrRN/BLK

BLK

BLU/BLK

VIO (Bue

INTERPRET

UNLESS OTHE DIMENSIONS. TOLER:

SURFACE FINISH

MATERIAL:

Page 89

ea7

c {3]

ane eo REMOTE sTAet

°. 2 L No. = MOMENTARY YUSH BUTTON

SONS RECEIVING THIS DRAWING reduction Forbidden ithe! the spe. ‘Gt ata tne, bas Gatos Calon. onal fied and nother recep ror the sr “fren ney aoe and tr manufac ssracen Reem no nit to reproduce ihe abject matter heat ues by ‘or Sten permesion fom the co ACS SS

REXT ASSY WHT

Buu

RED

WHT /BLK

GeON/BLK

ORN/aLK

BLK

BLL/BLK

VIO (BLE,

oen

td USED ON ISMTIALS aed DATE owere [carck | evore mB |PRODUCTION RELEALE [2/2s/r/3 Ai < leevisep pee EcN 1282 [this (——— 1%

ATARI INCORPORATED 14600 Winchester Bovlevard 4K Los Gatos, Californe 95030

™ <SCHEMATIC, RT-S&

REMOTE CONTROL BD, ‘CHECKED 'UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. TOLERANCES ON. DESIGN ENGINEER FRACTIONS = 41/16 x = 4.1 ANGLES » 21° eres) SURFACE FINISH \~ xxx = © 010 PROJECT ENGINFFR

DOCUMENT CONTROL on anvavuss

Page 90

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 91

ASSEMBLY TITLE # REMOTE CONTROL BOARD P/L 003193 PARTS LIST SPECIFICATION Page | of 1 | Drawn Checked

Innovative Elec. Eng

cee a og Pd PT PO

ItemPart NumberQ

003194 1 61-011C Circuit Board (Remote Control) SPDT Toggle Switch, PC Mount, w/Panel Dress Nut (C&K #7107 P3 DC B E A7807) SPDT Momentary Pushbutton Switch, PC Mount, w/Cap & Bezel (C&K #8121C 8018-2 w/8025) 62-007

4A003159-011Remote Control Cable
578-250011Cable Tie, Screw Down
675-24781Screw, Machine, Rd. Hd., Cross Rec #4-40
775-0541Washer, Lock, Int. Tooth, Steel #4
875-914S1Nut, Machine, Hex #4-40
Page 92

on eed } 88 238 98 — ES qzaue sce _ aooaRg82 To i 7 ° ; 8}

  • Race | BUTTON [o) it 10! it 12
iolReeRc'

Prod lo] [9|

ro10]°
tot1!lo}

boa fou tt

COMPONENT SIDE SHOWN

  • ROUTE AS SHOWN,

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL, Reproduction Fore witout he She wren rete of a, hs drauig yd

GS eee eee ain ome Eppa werner Soca nar earners poration INTERPRET TH PER USAS! V1

UNLESS OTHER DIMENSIONS TOLERAt

FRACTIONS ANGLES = SURFACE FINISH ® aw

ic a Se /

Seeeeeeoes

ers 2] P/L ne NENT ASSY USED ON

Page 93

J BO faue Buce ORANGE arya eLue Peo waren AL oen/aue

“4 47 :000

COMPONENT SibE SHOWN

SHOWN,

SONS RECENVING THIS DRAWING

iene INITIALS and DATE: DESCRIPTION parte | cueck. 2lashs Pie oe B lPROLOCTIONN RELEATE © [REVISED PER EN 1282

2)ave > paces)

° ees ol ome j 0;

Ros RoT ° 10 ° is Lo Q1

fe) ° oO; ec3 (KeMore) ace ° 'o ;o fo)

  • Oo] Ree a2c1 lo ro 0 ° ° fo)

°

y SS ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030 UNLESS OTHERWISE SPECIFIED DIMENSIONS. ARE IN INCHES ‘TOLERANCES ON: FRACTIONS =s146 x= 4.1 ANGLES = «1° ere) SURFACE FINSH V~ xax = + 010) ™ ASSEMBLY, RT-8 REMOTE CONTROL BD

DRAWING NO ACS MATERIAL:

ZBiIs2 suet 4 NEXT ASSY

Page 94

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 95

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 96

ATARI INC 14600 WINCHESTER BOULEVARD, LOS GATOS, CALIFORNIA 95030 + TELEPHONE (408) 374-2440 - TELEX 357-488.