CATHODE RAY TOMES

Championship Sprint TM-292 1st Printing

Championship Sprint (rev 3) (Atari Games, 1986) · Technical Manual · 92 pages · 94 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

Atari Games Corporation Customer Service

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Games Customer Service offices:

UNITED STATES

Parts and Service

California Customer Service Office 737 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035-1110 Telex 17-2976 (Monday-Friday, 7:30-4:00 pm Pacific Time) s (408) 434-3950

EUROPE

Parts and Service

European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) s 062-52155

Page 3

Championship Sprint’ Operators Manual

with Illustrated Parts Lists

Page 4

Championship Sprint

© 1986 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private usc, without permission from the publisher. The game play, ali graphic designs, this technical manual, its accompanying schennatic cliagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles While legal action is pending. If infringers are convicted, Courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up io $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Aayone who purchases such copies risks forfeiting such agame

Published by: Atati Games Corporation 575 Sycamore Drive P.O. Box 361210 Milpitas, California 95035

Printed in the U.S.A. 9Q

Page 5

Championship Sprint

Notice Regarding Non-ATARI® Parts

hy WARNING —A

Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-ATARI parts in the game
  • Modify or alter any circuits in the game by using kits or parts 2of supplied by Atari Games Corporation

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. it has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential arca or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following

  • All green ground wires in the game are properly connected as shown in the game wiring diagram © The power cord is properly plugged into a grounded three-wire oudet © The game printed-circuit boards (PCBs) are properly installed with the Electromagnetic Interference (EMI) ground plane If you are still unable to solve the interference problem, please coniact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Championship Sprint

Table of Contents 1 Set-Up How to Use This Manual M1 Inspecting the Game 12 Installation of Control Panel 13 Control and Switeh Locations 13 Coin and Game Option Settings 13 Operating Modes 13 Game Play 1 ! Operator Hints

Self-Test RAM/InterrupyROM Tesi 6502 Processor Test Pedal Test Calibration Procedure Leta Test Alphanumeric Test Scrolling Playtield Test Motion Object Test Motion Object Height 1 Color Bar Test Color Purity Te: Convergence Test Accounting Information Reset Saved Information Sereen Switch Settings LS)

3 Maintenance Preventive Maintenance 3 Preventive-Maintenance Intervals 3 Removing the Control Panel 3 Cleaning the Pushbutton Leaf Switches . 3 Maintaining the Steering Wheel Controls 3-2 Cleaning the Coin Mechanism 33 Cleaning the Interior Components 33

Corrective Maintenance . 35 Removing the Video Display : 35 Removing the Steering Wheel . 3-0 Disassembling the Steering Wheel . 36 Reassembling the Steering Wheel : 36 Removing the Foor Pedal Controls : 3-0 Removing the Game PCBS . . 3-6 Removing the Fluorescent Light Assembly. . . 38 Removing the Speakers... . : 38

4 Troubleshooting Troubleshooting Aids Troubleshooting Techniques Soldering Techniques Troubleshooting Static-Sensitive Devices

5 Illustrated Parts List See List of Hlustrations that follows,

6 Kit Installation Introduction, Gi Kit Parts Inventory Tools Required Conversion Instructions . ere we ’ Reset the High Score Table and the Accounting Information

iv

Page 7

List of Illustrations

Figure 1-1 Figure 1-2

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17 Figure 2-18 Figure 2-19 Figure 2-20

Figure 3-1 Figure 3. Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 5-1 Figure 5-2 Figure 5-3 Figure 5 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5

Table 1-1 Table 1-2 Table 1-3 Table 3-1 Table 6-1 Table 6-2 Removing Control Panel from. Shipping Position Control and Switch Locations

RAM Test Fails Interrupt Test Fails ROM Test Fails Reset Retry Communications Fails Music/RAM/ROM Fails Sound Output Sound Status... Pedal Test Passes Leta Test Alphanumeric Test . Scrolling Playfield Test Motion Object Test Motion Object Height Test Colox Bar Test Color Purity Test Convergence Test . Accounting Information Reset Saved Information Screen Switch Sertings

Control Panel Removal. . . : Maintaining the Steering Wheel Controls Video Display Removal . Game PCB Removal Fluorescent Light Assembly Removal Speaker Removal

Removing IC (Cut-Pin Method) Removing IC Pins Removing Solder from Plated-Through Holes Removing Solder from Lead Connection Pads Cabinet-Mounted Assemblies Control Panel Assembly 7 Steering Wheel Control Assembly Fluorescent Tube Assembly Switching/Linear (S/L) Power Supply Assembly Foot Pedal Assembly Coin Acceptors, Inc. Coin Door Assembly Printed-Circuit Board Mounting Hardware Central Processing Unit PCB Assembly Video PCB Assembly Audio Il PCB Assembly

Kit Part Locations Attraction Film Replacement . Control Panel Replacement a bev veeceees Installing ICs into CPU PCB Assembly 0000. Installing ICs into Video PCB Assembly

List of Tables

Game Specifications Coin and Credit Option Settings . Game Option Settings Recommended Preventive-! Maintenance Intervals . Kit Parts Inventory Integrated Circuits in Championship Sprint Conversion Kit Charnpionship Sprint

re

6.

Page 8

Championship Sprint

Safety Summary

The following safety precautions apply to all game operators and service personnel, Specific warnings and cautions will be found throughout this manual where they apply.

A WARNING A

Properly Ground the Game. Players may reccive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a 2-wire oudet, we recommend you hire a licensed electrician to install a grounded ouilet. Players may reccive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control panel nly then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify thar the game's power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid clectical shock because high voltages may exist within the display circuitry and cathode-ray tube(CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momengarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your pla Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game, Replacement fuses must match those replaced in fuse type, volrage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach Ail Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz, line power (i.c., United States) must not be operated in countries with 50 Hz line power (i.e., Europe). The fluorescent light baliast wansformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification jabel of your game for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In all Atari publications, notes, cautions, and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions
WARNING—Players and/or technicians can be injured or killed if instructions are not followed. (The word WARNING is always surrounded by international warning symbo!s—triangles with exclamation mai side of them.)
Page 9

Chapter 1

How to Use This Manual

Your System II cabinet is designed to be used for a variety of games. The System II cabinet comes with a $ tem II game installed at the factory. However, if you already have a System II cabinet, any available System IL game can be purchased as a kit for easy installation. This operators manual is for the Championship Sprint” game, and is supplied either with System II cabinets that have the Championship Sprint game instalied at the factory or with Championship Sprint kits that can be installed in the field

This manual includes information for setting up, playing, and maintaining your System II Championship Sprint game. If you have purchased a Championship Sprint kit to change an existing System II game into a Championship Sprint game, Chapter 6 of this manual contains all the necessary information for installing the game kit. This: manual is divided into the following chapters © Chapter | contains set-up information © Chapter 2 contains self-test procedures. © Chapter 4 contains preventive and corrective maintenance procedures. ¢ Chapter 4 contains troubleshooting information. © Chapter 5 contains illustrated parts lists. © Chapter 6 contains procedures for installing the Championship Sprint kit

Page 10

Setp

System II Paperboy™ games located in the field were built with a different power supply, Audio PCB, and utility panel than the System UU Championship Sprint games. Refer to Chapter 5, Illustrated Parts List, in the Paperboy Operators Manual (TM-275) for information regarding these components. The figure number and part number for each of these components follow:

Figure No.Part No.Component
5-5A037671-16Linear Power Supply
5-12A043046-01Regulator/Audio II] PCB
5-6A043 146-01Utility Panel
Refer toA043785-xxSierracin 5-Volt Power

CO-275-01 Supply Supplement

For the wiring and schematic diagrams, refer to the Paperboy Schematic Package Supplement (SP-275) and the Sierracin 5-Volt Power Supply Supplement (CO-275-01)

NOTE If you do not have the Paperboy manuai or the supplements, use the form in the back of this manual to obtain a free copy.

Wiring and schematic diagrams for the System II Championship Sprint game circuitry are contained in the Schematic Package Supplement (SP-292) included with your game. This chapter includes information required to set up and play your Championship Sprint game. Carefully read the information in this chapter before applying power to the game,

A WARNING A To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you have only a two-wire Outlet, we recommend that you hire a licensed electrician to install a grounded outlet Players can receive an electrical shock if the cabinet is not properly grounded Do not touch internal parts of the display with your hands or with metal objects. Championship Sprint

Inspecting the Game

A WARNING A Do not plug in the game until you have completed the following inspection steps.

Please inspect your System Il Championship Sprint game (or kit) carefully to ensure that the game (or kit) is complete and delivered to you in good condition. Figure 6-1 shows the locations of the component parts of the assembled game. Refer to Chapter 6 for a list of the kit parts. Table 1-1 lists the space, power, and environmental requirements. Inspect the factory-assembled game as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows:

a. Ensure that all plug-in connectors (On the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that ali plug-in integrated circuits on each PCB are firmly plugged into their sockets.

° Inspect the power cord for any cuts or dents in the insulation.

d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 300 V-A, 239 W RMS maximum with kit parts installed Temperature +5° to +38°C (+37° to + 100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. Games) 198 to 264 VAC (Irish Games) Width 25.25 in. (64 cm) Depth 37% in. (95 cm) with control panel installed Height 72 in. (183 cm) Weight 330 Ibs. (149 kg) maximum with kit parts installed

Page 11

Championship Sprint

is mounted in place. Check that the green ground wire is connected. ¢. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), speakers, and the fluorescent tube. Make sure they are mounted securely and that the green ground wires are connected. Inspect the Championship Sprint kit as follows

  • Verify that all of the Championship Sprint kit parts listed in Table 6-1 of this manual are included in your kit.
  • Examine the kit parts for dents, chips, or broken parts.

Installation of Control Panel

For packaging purposes, the Championship Sprint control panel is shipped inside the cabinet. The panel is mounted on a single metal bracket on the inside left side panel in the rear of the cabinet. (See Figure 1-1.) Perform the following procedure to remove the control panel from the cabinet.

  • Using a Phillips screwdriver, remove the two screws holding the metal bracket to the cabinet. Remove the control panel from inside the cabinet
  • Using a 1/8-inch hex driver, remove the two screws and washers holding the metal bracket to the control panel. Save this hardware. Discard the bracket or remount it in the cabinet for future control panel storage.
  • Replace the existing control panel with the Championship Sprint control panel. Refer to Chapter 3, Removing the Control Panel.

Control and Switch Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 5-1.)

Volume Control The volume control is located on the Audio I] PCB behind the upper coin door. (See Figure 1-2.) The volume control adjusts the level of sound produced by the game.

Coin Counter The coin counter is located on the inner cabinet wall opposite the upper coin door. The coin counter records the number of coins deposited.

Self-Test Switch

The self-test switch is located on the Audio I] PCB behind

the upper coin door. (See Figure 1-2.) The self-test switch Setup

selects the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation. (See Figure 1-2.)

Coin and Game Option Settings

The System IJ cabinet has two dual-in-line package (DIP) option switches located on the CPU printed circuit board (PCB). © The option switch at location 6/74 is for selecting coin options.

  • The option switch at location 5/6A is for selecting game options. Set the coin and credit option settings, game option settings, and automatic high score reset setting by changing the settings of the DIP switches. Refer to Table 1-2 and Table 1-3 for the available options and default (recommended) settings. To change these settings, first remove the thin film of plas tic covering the option switch, Use a pen or a sharppointed instrument to slide the appropriate small buttons. to different settings. Right is the on position, and left is the off position, The stecring wheel controls and the pushbuttons are nor used to change these settings.

Operating Modes

Championship Sprint has four operating modes: Attract, Play, High Score, and Self-Test. Attract Mode

The Attract Mode begins either when the game is plugged in or after exiting the Play, High Score, or Self-Test Modes The Attract Mode ends when the correct amount of coins or tokens are inserted and the start button(s) are pressed, or when the self-test switch is turned off. The Attract Mode continuously cycles through the following events: © Title Page-—The title CHAMPIONSHIP SPRINT is displayed on an explosion/checkerboard background. © High Score Table—The top 30 scores are displayed. (Championship Sprint Racing Team). The top 3 scores are highlighted at the top of the screen. Demo Mode—The drone cars run two laps on each of the eight tracks,taking each checkered flag. During the Attract Mode, if a whole new credit (not partial credits) is entered into the game through the coin mechanisms, a gong sound is played. The credit status and current coin mode are constantly displayed and updated throughout the Attract Mode.

Play Mode

Play mode begins when the correct credit is entered and the blue or red start button is pressed. Refer to Game Play for playing information.

Page 12

Championship Sprint secup

Control Panel

Metal Bracket

Figure 1-1 Removing Control Panel from Shipping Position

Page 13

Championship Sprint

Coin Counter Game Option Switch

Audio li PCB set lp

Coin Option Switch

Self-Test Switch

Volume Controi

Figure 1-2 Control and Switch Locations

High Score Mode

In the High Score Mode, if a player's score is among the top 30, the player can enter the desired initials by turning the steering wheel to select the initial, and by pressing the start button or accelerator pedal to insert the initial. Self-Test Mode

You can set the Championship Sprint game to the Self- Test Mode by turning on the self-test switch located on the Audio I] PCB bebind the upper coin door. Refer to Chapter 2 for detailed self-test information.

Game Play

The game piay begins once players select a car by depositing coins into the proper coin slot. One coin slot is designated for each of the two player cars—biue, or red. The first player to press start is given the option to select one of eight unique starting tracks. A select screen displays all tracks. Players choose the desired starting track by using the steering wheel to indicate the desired track, and by pressing the accelerator pedal to siart the game on the chosen track. At the starting line, a green flag indicates the race is on During the race, the lead player's lap number is flashing. A white flag appears when the last lap is on. At the finish line, a checkered flag awaits the winner. At the end of each heat, players go to the “Winner's Circle” where racing statistics show the players’ rankings, their best lap times, and their average lap times. Plavers who beat the drone cars continue in the game by going on to the next heat, Each new heat takes place on a new track During each race, players compete to collect gold wrenches that appear randomly on each track. These wrenches are a key element in the game because players: can trade them in for custom car features. Players can customize their cars to suit their driving skills with the following options:

Page 14

Set-Up Championship Sprint

Table 1-2 Coin and Credit Option Settings

Settings of 8-Toggle Switch on Championship Sprint CPU PCB (at 6/7A) 1 2 3 4 5 6 7 8 Option

Coins Per Credit

OffOff1 Coin 1 Credit <4
OffOn2 Coins 1 Credit
OnOff3 Coins 1 Credit
OnOn4 Coins | Credit

All Coin Mechanisms

OffOffOff1 Coin Counts as 1 Coin <4
OffOffOn1 Coin Counts as 2 Coins
OffOnOff1 Coin Counts as 3 Coins
OffOnOn1 Coin Counts as 4 Coins
OnOffOff1 Coin Counts as 5 Coins
OnOffOn1 Coin Counts as 6 Coins
OnOnOff1 Coin Counts as 7 Coins
OnOnOn1 Coin Counts as 8 Coins

Bonus Adder

OffOffOffNo Bonus Adder
offOffOn2 Coins Give 1 Extra Coin
OffOnOff4 Coins Give 1 Extra Coin
OffOnOn4 Coins Give 2 Extra Coins
OnOffOff5 Coins Give 1 Extra Coin
OnOffOn3 Coins Give 1 Extra Coin
OnOnOnFree Play

4 Manufacturer's recommended settings

Table 1-3, Game Option Settings

Settings of 8-Toggle Switch on Championship Sprint CPU PCB (at 5/6A) 1 2 3 4 5 6 7 8 Option

Drone Difficulty

Off On — Easy

OffOffMedium <4
OnOffMedium Hard
OnOnHard

Track Hazard Difficulty

OffOnEasy
OffOffMedium <
OnOffMedium Hard
OnOnHard

Number of Wrenches to Customize Car

OffOn2
OfOff3
OnOff4
OnOn5

Automatic High Score Reset After 2000 Plays Off Yes 4 On No

4 Manufacturer's recommended settings

Page 15

Championship Sprint

Super Traction—gives players more maneuverability around sharp turns. Turbo Acceleration—gets players off to a fast start at the beginning of the game or after they crash. Higher Top Speed—helps players stay in the jead, only if they can handle the high speed. (Beginning players learn quickly that this feature should be used with more practice.) Fast Chopper—increases the speed of the helicopter recovery sequence. There are five levels of cach of these features for a total of 20 custom car bonuses. After completing five levels of Fast Chopper, players are also given an unlimited option of increased score, to motivate more skillful players who. can gradually acquire all 20 car bonuses. Operators can select the number of wrenches required for each car bonus. Championship Sprint is shipped on a 3-wrench-perbonus setting. These bonus wrenches also provide additional player incentives that result in higher earnings: Players get to keep acquired custom car features if they lose to a drone car, as long as they use the add-a-coin feature in the game. Also, bonus wrenches are awarded to new players who enter a game on the more difficult tracks. Additionally, a bonus wrench is awarded to each winning car that betters the existing ‘‘best Jap time’’ for each track. Championship Sprint has eight different tracks, each one introducing new challenges. Jump ramps, opening and closing gates, hidden short cuts, over/under passes, and banked turns all require special driving maneuvers. Throughout each heat, players are introduced to new track obstacles such as oil spills, twisters, traffic cones, and “‘poppers.”’ Special bonus score pads also appear that players can run over for points. Players will crash whenever they hit a wall at high speeds. Each time they crash, they must wait for a recovery period, indicated by the rescue helicopter that comes on the screen, To complete the driving experience, Championship Sprint has detailed animation and custom stereo music with realistic sound effects.

Operator Hints

Here are some pointers for maximizing earnings from your System II Championship Sprint game.

Maximizing Earnings

The key to maximum earnings is striking a midpoint on game times. Initially, game times should be short enough to allow higher player turnover. At the same time, game times must be long enough to give the player good value and ensure repeat play. Championship Sprint has a comprehensive statistics and coin accounting package, which is described in greater detail in Chapter 2 of this manual. To find out whether or Set-Up

not your players are getting adequate value for their money, you should evaluate the following information.

NOTE For your convenience, a pre-printed, tear-out statistics sheet is included at the back of this manual Use this sheet to track your Championship Sprint game statistics.

Average Game Times/Average Time

Between Coin Drop

Two statistics are crucial in evaluating the appropriate option settings on your Championship Sprint game. First, check the average game time which is shown in the Accounting Information screen in the Self-Test Mode. If the game is set at the factory-recommended settings, initial game times should average between 2:00 and 3:00. If this is not the case, you should then check the average time between coin drop, which can be calculated by two readings shown on the Accounting Information screen. To calculate: divide the total play time by the total games: ((No. of hours playedx 60 + minutes) + total games) x 60 = seconds between coin drop. This number should range from 65 to 90 seconds. Ifa high percentage of your average game times are under 90 seconds, and your average time between coin drop is under 50 seconds, the current game settings may be too difficult. You should consider changing the drone difficulty to the EASY setting. If game times are still too short after one or two weeks, try changing the track hazard difficulty to the EASY setting. Conversely, if a high percentage of your average game times are over 3:30, and your average time between coin drop is over 100 seconds, the current game settings may be roo easy. Try changing the drone difficulty and the track hazard difficulty options to the MEDIUM HARD setting.

NOTE The previously mentioned recommendations are based on one coin per play, U.S. currency.

Game Sounds

Your System Il cabinet with the Championship Sprint game uses more effective audio than previous games, which results in more player involvement and enjoyment. The System II games use advanced digital soundgeneration techniques to create realistic musical instrument sounds (such as clarinets, harmonicas, drums, and violins). Although a player may not be consciously aware

Page 16

Set-Up

of the music, it has a direct effect on the excitement and emotional experience of the game The Championship Sprint game creates ear-catching sound effects, which are designed to give feedback to make the player believe that the game is responding directly to his actions. To maximize the player’s enjoyment of this enhanced audio and maximize your earnings, consider the following hints: I. The game location should be a relatively dead acoustical environment. The goal is to minimize unnecessary sound reflection, so that the sounds from the Championship Sprint game won't be drowned out by the accumuiation of other sounds that bounce around the room. Carpets help eliminate sound reflections from the floor. Acoustical tile is also useful, especially if you have low ceilings.

  • If you use an environmenial sound system or a stereo, consider lowering its volume or perhaps even turning it off. In the days when video games just made harsh

1-8 Championship Sprint

beeps and boops, a central sound system helped make up for the lack of drive and excitement in a game's sounds. But your Championship Sprint game is very musical, and asound system interferes with the game’s ability to interest players and draw bystanders. Be concerned with the overall volume levels in arcade environments, The goal is to involve the players’ emotions, not to damage their hearing. To a certain point, raising the game volume helps add to player excitement, but above that level it creates hearing fatigue and the high volume starts to drive players away. Rather than turning up the volume on the Championship Sprint games to cut through the background sound level, try lowering the volume of any neighboring games that have sounds which are not an attractive or important element. Careful placement of games and attention to unnecessary noise sources can also help increase the player’s sense of game involvement and interaction.

Page 17

Chapter 2

Self-Test

This game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and sent through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. Coin and game option settings are displayed in the Self-Test Mode. Thirteen self-test screens provide a visual and audible check of the Championship Sprint™ game circuits. Refer to Chapter 1 for the self-test switch location. The SelfTest Mode can be entered immediately after turning on the game power, either from the Play Mode or from the Attract Mode. If the self-test switch is turned on during the Play or the Attract Mode, the first display to appear is the 6502 Processor Test. By pressing the red start (right) button, the self-test advances to the Pedal Test. The self-test chen advances from the Pedal Test to the end. The game power must be turned off, the self-test switch turned on, and the game power turned on again to start the self-test with the RAM/Interrupt/ROM Test. The following self-test procedure is presented in the sequence in which the self-test screens appear when the self-test switch is turned on and then the game power is turned on. Turning off the self-test switch at any time during the self-test causes the game to return to the Attract Mode.

NOTE During any of the self-tests, press the red start (or right) button to advance to the next screen,
Page 18

Sell Test

RAM/Interrupt/ROM Test The RAM/InterrupVROM Test screens are shown in Figures 2-1, 2-2, and 2-3. These screens display the failure information for the RAM. interrupt, and program ROM circuitry on the CPU and Video PCBs. If the RAM/InterrupV/ROM test passes. the display advances to the 6502 Processor Test

The RAM test checks the condition of the 7-11 microprocessor RAM, zcro page RAM, motion object RAM, playficld RAM, alphanumeric RAM, and associated circuitry located on the Video PCB. If the RAM test fails, an error message gives the location of the failed RAM or associated circuitry on the Video PCB as shown in Figure 2-1 If the zero-page RAM or associated circuitry fails, the screen turns red and the address location of the failed component flashes continuously to facilitate troubleshooting,

Figure 2-1 RAM Test Fails

INTERRUPT

Figure 2-2 Interrupt Test Fails Championship Sprint

Bi Hal bAg USER

Figure 2-3, ROM Test Fails

After the RAM test passes, the interrupts on the CPU and Video PCB are checked. If the interrupt test fai message as shown in Figure 2-2 can appear on a green screen, which indicates a possible vertical-blanking or interrupt-logie failure After the interrupt test passes, ali cight of the program ROMs on the CPU PCB are tested for checksums. If the ROM test fails, an error message gives the location of the failed ROM or associated circuitry as shown in Figure

6502 Processor Test The 6502 Processor Test screen provides visual and audible information to indicate the condition of the 6502 sound microprocessor and associated circuitry. All functions of the sound microprocessor are checked including: RAM/ROM, interrupts, music synthesizer, and sound-cffects processor, Basic communication between the T-11 (master) and the 6502 (slave) microprocessors is also checked. The 6502 test starts with a resct/communications check that first resets the 6502 and then checks for proper response to start up protocol. This test checks the communications ports (T-11 to 6502 and 6502 to T-11), the 6502 reset circuit, and the general condition of the 6502. If the 6502 circuitry does not respond properly to the reset, the system retries the reset procedure ten times. Then an error message and retry count number is displayed as shown in Figure 2-4. If the 6502 circuitry fails to reset through all ten attempts, acommunications error message is displayed as shown in Figure 2-5. If the reset/communications check passes, then the condition of the 6502 microprocessor, RAM, ROM, interrupts, music (Yamaha) synthesizer, and associated cir-

cuitry is checked. If one or more of these circuits fails, an

error message is displayed as shown in Figure 2-6,

Page 19

Championship Sprint

¥

RETRY: 6

PROCESSOR. TEST

MUNICATIONS FAILED + 4

PRESS ADVANCE TEST

Figure 2-5 Communications Fails

If the RAM, ROM, and music synthesizer check passes, then the music (Yamaha) synthesizer, and sound-ctfects generator (POKEY) sound outputs are checked. As each of these three tests is run, an appropriate message is displayed as shown in Figure 2-7. © YAMAHA TEST consists of cight tones in a major scale that alternate between left and right sound channels (16 tones total). © L. POKEY TEST consists of four tones ina major chord that come from the left sound channel. © R. POKEY TEST consists of four tones ina major chord that come from the right sound channel After the three sound output tests are completed, the sound status messages are displayed as shown in Figure 2-8.

  • NUMBER OF SOUNDS is the total number of sounds used in the Championship Sprint game. Sete Test

PRESS RED START TO ADVANCE TEST

Figure 2-7 Sound Output

© CURRENT IND is the Current sound selected for playing, Press the blue car button to select the sound numbers indicated by the CURRENT SOUND message shown in Figure 2-8. Turn the blue car steering wheel to sequence through the selected sounds. The sound status screen also indicates the condition of the left and right coin switches. Press the left and right coin switches, and check the screen for a corresponding LEFT COIN and RIGHT COIN message. (See Figure 1-2 in Chapter | for the switch locations.) Press the red start button to obtain the next serecn

Pedal Test ‘The Pedal! Test screen is shown in Figure 2-9, This screen indicates the condition of the two foot pedal potentiometers, A/D converter, blue car switch, and associated cir-

Page 20

Self-Test

\UMBER. RRENT SOUND:

TO ADVANCE

Figure 2-8 Sound Status

PRESS: RED START

Figure 2-9 Pedal Test Passes

cuitry. (It is assumed that the red start switch works because it was used to advance to this screen.) The Pedal Test screen is also used to calibrate the foot pedal potentiometers. Press the blue car button to obtain the Pedal Test screen shown in Figure 2-9. If the range of the foot pedal potentiometers (low to high) is large enough, then the message OK is displayed next to the appropriate control range reading. If the range is too small, then the message BAD is displayed.

Calibration Procedure

The foot pedal controls are calibrated at the factory and should recalibrate themselves during game play. However, if the foot pedals do not respond correctly, calibrate each one as follows: Championship Sprint

  • Press and hold down the blue car button. Press the red car button once.
  • While holding down the blue button, cycle each foot pedal to its extreme up and down positions. Check the display screen; each foot pedal range should read OK. Then release the blue car button. Press the red start button.
NOTE After completing the calibration procedure, you must press the red start button to save the calibration, Pressing the button also advances the screen at this point
  • Ifthe pedal problem persists, check the physical alignment of each foot pedal potentiometer.

Leta Test The Leta Test screen is shown in Figure 2-10. This screen indicates the condition of the steering wheel circuitry. Each wheel should display a zero value when the wheel is idle. Turning each wheel in either direction should change at least one of the zero values to a non-zero value. Press the red start button to obtain the next screen.

Alphanumeric Test

The Alphanumeric Test screen is shown in Figure 2-11. This screen indicates the condition of the alphanumeric ROM, alphanumeric color palettes, and associated circuitry. The displayed alphanumeric characters are in four rows, with the first row white, the second row red, the third row yellow, and the fourth row green. If not, then there may be a problem with the color palette select circuits.

LETA TEST

Low RES. LETA: op 90. 00 00

PRESS RED START: ITO ADVANCE TEST

Figure 2-10 Leta Test

Page 21

Championship Sprint

ALPHANUMERIC

. PRESS RED@ ART: TO.ADVANC

Figure 2-12 Scrolling Playfield Test

Press the red start button to obtain the next screen.

Scrolling Playfield Test

The Scrolling Playfield Test screen is shown in Figure 2-

  • This screen indicates the condition of the playfield ROM, playfield display circuits, and playfield color palettes. The display in Figure 2-12 shows a racetrack. Turn the blue car (left) steering wheel to control forward and backward scrolling. Turn the red car (right) steering wheel to control the right and left scrolling. Note that the display scrolls correspondingly. Press the red start button to obtain the next screen.

Motion Object Test

The first Motion Object Test screen is shown in Figure 2-13. This test indicates the motion object horizontal and Self-Test

MQTION OBJECT TEST

“OBJECT ¥

Figure 2-13 Motion Object Test

yertical display locations, motion-object color palettes, and the motion/playfield prioritizing logic circuit. The Motion Object Test screen should show 39 motion objects and four colored boxes (numbered 0 through 3). The left two boxes (0 and 1) should be red, and the right two boxes (2 and 3) should be green. The motion objects should be colored (from left to right) blue, light blue, purple, and white. Any error in color can indicate a problem with the coior palette select circuits. Turn the red car steering wheel to contol forward and backward scrolling, and the blue car steering wheel to control right and left scroliing. Note that the currently displayed motion object moves correspondingly. Move the motion object across the four colored boxes. Note that the motion object moves bebind the red boxes and in front of the green boxes. Press the bluc car button to select the next motion object and repeat the preceding procedure. This procedure checks the prioritizing logic circuitry, Press the red start button to obtain the next screen,

Motion Object Height Test

The Motion Object Height Test screen is shown in Figure 2-14. This test indicates the motion object height circuit and the horizontal load disable circuit.

Each successive column of motion objects should be 16 pixels taller than the last. The top 16 pixels of each column should be the same. Each column should adda new 16x 16 pixel stamp picture to the boom and slide the previous one up by 16 pixeis. Turn the blue car and the red car steering wheels to move the entire picture around on the screen. Press the blue car button to obrain a new set of motion objects. Press the red start button to obtain the next screen.

wv a

Page 22

Self-Test

MOTION OBJECT HEIGHT TES?

3: Se Pt

PRESS RED START TO ADVANCE ZEST

Figure 2-14 Motion Object Height Test

Figure 2-15 Color Bar Test

Color Bar Test The Color Bar Test screen is shown in Figure 2-15, This test indicates the condition of the color RAM, video amplifiers, and associated circuitry. Sixteen vertical grey-scale bars and three groups of sixteen vertical bars with shades of red, green, or blue are displayed. The brightest bar should be on the left and darkest (black) bar on the right, with a black frame around the screen. Each group of red, green, or blue should be split in half horizontally to show two fade scales, Each upper fade scale is ranged by changes in overall intensity {Z) and each lower fade scale by individual color intensity (R, G, B). This test helps to determine if white tracking is set properly (grey-scale bars range from white to grey). Refer to the white tracking procedure in the video display manual if adjustment is required. Press the red start button to obtain the next screen Championship Sprint

Color Purity Test

The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display to appear should be a red screen with the word RED displayed at the bottom of the screen as shown. in Figure 2-16. Press the blue car button, and the next display to appear should bea green screen with the word GREEN displayed at the bottom of the screen. Press the blue car button to obtain a blue, white, and finally a grey screen. After the grey screen, the display will repeat the same sequence. If the display characteristics are not correct, refer to the video display manual for the color-purity adjustment procedure or the possible cause of failure. Press the red start button to obtain the next screen.

Convergence Test

The Convergence Test screen is shown in Figure 2-17. This test indicates the condition of the display size, centering, linearity, and convergence. A violet dot pattern displays the red-to-blue convergence. Press the blue car button to obtain a white-dor convergence pattern. Convergence between any two colors should not exceed 9.7 mm in the middle of the screen and 1.2 mm in the corners. This pattern can also be used to set up screen size, centering, and brightness (black level), Press the red start button to obtain the next screen.

Accounting Information

The Accounting Information is shown in Figure 2-18. This screen provides a visual check of the current game statistics. The statistics information is accumulated either from the first time the game was tured on or from the last time the statistics were reset.

Figure 2-16 Color Purity Test

Page 23

Championship Sprint

ACCOUNTING INFORMATIC

LEFE COINS RIGHT COINS. ADD A: COINS. 1 PLAYER HEATS . 2 PLAYER HEATS. .

TOTAL GAMES . TOTAL. GAME. TIME .... AVERAGE GAME TIME... TOTAL: ON: TIM TOTAL PLAY TIS

PRESS RED START TO

Figure 2-18 Accounting Information

The following game statistics appear on the Accounting Information screen:

LEFT COINS shows the total number of coins deposited in the left or blue car coin mechanism.

RIGHT COINS shows the total number of coins depos: ited in the right or red car coin mechanism.

© ADD A COINS shows the total number of coins deposited in all coin mechanisms during the add-a-coin mode of game play only.

© 1 PLAYER HEATS shows the total number of heats or races that were run with one player only.

*¢ 2 PLAYER HEATS shows the total number of heats or races that were run with two players.

  • TOTAL GAMES shows the total number of coins deposited in all coin mechanisms: self-test

© TOTAL GAME TIM one- and two-pla and seconds.

  • AVERAGE GAME TIME shows the total game time divided by the total number of games in hours, minutes, and seconds. shows the accumulated time of all cr games played in hours, minutes.

TOTAL ON TIME shows the toral time in hours, minutes, and seconds that the game has been turned on

  • TOTAL PLAY TIME shows the total time in hours, minutes, and seconds that the game has been played (percent usage = total play time/total on time).

The game statis are accumulated from the first time the game is turned on or from the last time the statistics were reset

Reset Saved Information Screen

The Reset Saved information screen is shown in Figure 2-19. This screen resets the high score table and the accounting information. Use the following procedure to rcset these items:

  • Rotate the left st Fesct ting wheel to select the item to
  • Press the bluc car button to change the VO message to YES,
  • Press the red start button to reset the selected tables. After a brief PLEASE WAIT message is displayed, the self-test automaticaily advances to the next screen.

Switch Settings

The Switch Settings screen is shown in Figure 2-20. This screen indicates the current coin and credit option settings, and the game option settings of the two dual-in-line

RESET SAVED INFO

SELECT ITEM WITH BLUE BUTTON TO TOGGLE YES AND NO.

RESET HIGH SCORE TABLE? RESET ACCOUNTING INFO? YES

Figure 2-19 Reset Saved Information Screen

Page 24

Self-Test

SWLICH. SETTIN

CREDIT: MODE .. 1 COINS 1 CREDIT MECH. MULTIPLIER... 4 COIN COUNTS A

BONUS ADDER... NO BONUS ADDER

OPTION SWITCH SETTIN DIFFICULT OBSTACLES: MEDIUM WEENCHE 3 AUTO HIGH SCORE PRESS RED START TO

Figure 2-20 Switch Settings

2-8 Championship Sprint

package (DIP) switches at locations 6/7A and 5/6A on the CPU PCB. ¢ The option switch at location 6/7A is used for selecting the coin and credit options. © The option switch at location 5/6A is used for selecting the game options. Set the coin and credit option settings and the game option settings by changing the settings of the DIP switches located on the CPU PCB. Refer to Tables 1-2 and 1-3 in this manual for the available options and default (recommended) settings. To change these settings, first remove the thin film of plastic covering the option switch. Use a pen or a sharppointed instrument to slide the appropriate small buttons to different settings. Right is the om position, and left is the off position. The steering wheel controls and the push buttons are mof used to change these settings. Press the red start button to return to the 6502 Processor Test.

Page 25

Chapter 3

Maintenance

This chapter includes preventive and corrective maintenance procedures for the Championship Sprint™ game components that are subject to the most use. To assure maximum troubic-free operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, reassembly, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 5, Illustrated Parts Lists, to aid in locating the parts of this game that are mentioned, but not illustraied, in the maintenance procedures.

Page 26

Maintenance Champioaship Sprint

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play, However, for those components listed in Table 3-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.

A WARNING A

To avoid possible electrical shock, turn off the game before performing any maintenance procedures. The 5-volt switching power supply for this game does not have a shield. This power supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have turned off the power to the game.

Removing the Control Panel

Perform the following procedure to remove/replace the control panel. (See Figure 3-1.)

  • Use a 1/8-inch hex driver to loosen the two screws securing the lower retainer to the cabinet. nN Unlock and open the coin door on the front of the cabinet
  • Carefully reach up through the coin door opening and release the spring-draw latches located under the control panel on both sides of the cabinet.

Table 3-1 Recommended Preventive- Maintenance Intervals

Steering Wheel lubricate, and tighten Control hardware at Ieast every three months Foot Pedal Control Lubricate, and tighten hardware at least every three months. Coin Mechanism Inspect whenever you collect coins Clean at least every three months.

  • Use a 1/8-inch hex driver to remove the two screws and washers securing the front of the control panel to the cabinet

Grasp the stcering wheel and gently lift until the bottom edge of the control panel clears the cabinet. ©. Carefully slide the top edge of the control panel from under the lower retainer.

Lift the control panel from the cabinet just far enough to expose the control-panel harness connector.

  • Disconnect the steering wheel harness connector and remove the control panel from the cabinet.
  • Replace the control panel in the reverse order of removal.

Cleaning the Pushbutton Leaf

Switches

Perform the following procedure to clean the leaf switch contacts and tighten the securing hardware.

  • Follow the procedure described in the preceding steps 1-8 for removing the control panel.
  • Use electrical contact cleaner to clean the contacts. Do not burnish them. When the pushbutton is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature. Then use the Self-Test to verify proper switch contact. (See Figure 3-1.)
  • Using a 15/16-inch open-end wrench, tighten the stamped nut securing the pushbutton leaf switches to the control panel

Maintaining the Steering Wheel Controls

Preventive maintenance on the steering wheel controls consists of inspecting the stecring wheel housing for excessive wear or dirt, inspecting the Coupler PCB Assembly for damage, lubricating the friction-producing surfaces of both white bearings, and, if necessary, replacing or tightening the securing hardware. Perform the following procedure to lubricate and tighten the steering wheel controls. (See Figure 3-2.)

  • Open the control panel as previously described,
  • Apply a film of light oil (Atari part no. 107013-001) to the lubrication points shown in Figure 3-2
  • Using a 5/16-inch nut driver (or an appropriate tool), tighten the screws holding the steering wheel assembly to the contro! panel.
Page 27

Championship Sprint

Lower Retainer

1/8-inch Hex Head Screw (2 places}

Button-Head Screw (2 places) Control Panel

Harness Connector (2 places} Maintenance

Spring Draw Latches

Coin Door

Figure 3-1 Control Panel Removal

Cleaning the Coin Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior Components

Perform the following procedure to clean the components inside the cabinet 1. Unlock and open the rear access door.

Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a cireuit for discharging the high voltage to ground when power is removed. However, to make certain, al discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap

c. Wait two minutes and repeat part b:

A WARNING A

Turn off the game power, and be sure that the on/off switch cover is in place. However, do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning tools.

CAUTION eful when cleaning the electrical side the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.
Page 28

Maintenance Championship Sprint

Lock Washer Steering Wheel

Logo Cover

Bolt

Housing

‘Thompson Bearing

Bolt ‘ Coupler PCB Assy

Encoder Hub Washer

Figure 3-2 Maintaining the Steering Wheel Controls

  • Use a vacuum cleaner with a soft long-bristied brush the cabinet. Be sure to clean the electrical components attachment or use a soft-bristled paint brush to re- thoroughly (power supplies, PCB assemblies, display, move loose dirt and dust accumulated on the inside of ete.).
Page 29

Championship Sprint Maintenance

Corrective Maintenance

Corrective maintenance Consists of removal, disassembly, reassembly, and replacement of game components. The following procedures are provided for components that may require Corrective maintenance.

Removing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-3.) 1, Turn the game power off and wait two minutes, Unplug the power cord.

  • Use a 1/8-inch hex driver to remove the two screws securing the lower retainer to the cabinet.
  • Grasp the display shield on the bottom edge and gently pall it out about a half-inch from the cabinet.
  • Gently lower the display shield to free the top edge from under the speaker grille.
  • Use a flat-head screwdriver to remove the staples. if any, securing the bezel to the cabinet.
  • Remove the bezel.
  • Unlock and open the rear access door.

A WARNING A

High Voltage The video display contains lethal high voitages To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to mininiize X-radiation. However, to avoid possible exposure 10 soft X-radiation, never modify the highvoliage circuitry Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

8. Discharge the high-voltage from the cathode-ray tube

(CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Atach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

Bezel _3/8-inch Mounting Nuts

Display Shield oN

1/8-inch Hex-Head Screw (2 places)

Lower Retainer Video Display (4 places)

Display Harness Connectors

Figure 3-3 Video Display Removal

Page 30

Maintenance

c. Wait two minutes and repeat part b.

  • From the back of the cabinet, unplug the display harness connectors and disconnect the green ground wire from the clip on the video display chassis.

A WARNING A To avoid dropping the video display out of the game cabinct, use extreme care when removing the display-mounting nuts. We recommend that a second person carefully hold the display chassis from the back of the cabinet while the mounting nuts are being removed.

  • From the front of the cabinet, use a 3/8-inch wrench to remove the four nuts and flat washers securing the display to the cabinet.
  • Carefully slide the display out through the front of the cabinet.
  • Replace the video display in the reverse order of removal.
NOTE Whenever the cathode-ray tube is replaced, readjust the brightness, purity, and convergence as described in the display manual,

Removing the Steering Wheel

Perform the following procedure to remove/replace the steering wheel. (See Figure 3-2.)

  • Open the control panel as described under Preventive Maintenance. . Disconnect the harness connectors from the coupler PCB connector.
  • Using a 5/16-inch nut driver, remove the six screws holding the steering wheel assembly to the control panel.
  • Lift the steering wheel assembly out of the control panel.
  • Replace the steering wheel in the reverse order of removal. Reconnect the harness connectors to the coupler PCB connector.

Disassembling the Steering

Wheel

Perform the following procedure to disassemble the steering wheel assembly. (See Figure 3-2.)

  • Using a 5/16-inch nut driver (or appropriate tool), remove the six screws holding the steering wheel assembly to the control panel.

3-6 Championship Sprat

  • Using a 7/16-inch nut driver (or appropriate tool), remove the bolt and washer from the bottom of the encoder hub.
  • Pull the shaft from the housing. 4 Remove the three screws holding the cover to the shaft Remove the 3/8-inch x 1-inch screw from the shaft. wn

Reassembling the Steering

Replace the steering wheel parts in the reverse order of removal. After reassembling the steering wheel, be sure that the hub can spin freely in the slot of the optical coupler on the PCB.

Removing the Foot Pedal

Controls Perform the following procedure to remove/replace the foot pedal controls.

  • Disconnect the foot pedal harness assembly from the cabinet control harness assembly located inside the rear of the cabinet. nw . Using a 7/16-inch hex driver (or appropriate tool), remove the nuts and washers from the two bolts holding the foot pedal frame to the pedestal enclosure rear wall. Remove the nut and washer from the adjustable glide protruding through the front of the pedal frame Remove the foot pedals.
  • Replace the foot pedals in the reverse order of removal.

Removing the Game PCBs Perform the following procedure to remove/replace the game PCBs.

CAUTION Do not attempt to remove the CPU and Video PCBs while they are connected together. If you are going to remove both of these PCBs, remove the Video PCB first to avoid damaging the PCBs or the edge connectors.

Video PCB Perform the following procedure to remove/replace the Video PCB. (See Figure 3-4.)

  • Turn the game power off.
  • Unlock and open the lower rear access panel. . Remove the four thumb nuts holding the EMI cover to the ground plane.
Page 31

Championship Sprint

a Maintenance

CPU Printed-Circuit Board

Edge Connector

Yellow Connector

Red Connector (Black Wire on Top)

Red Connector (Brown Wire on Top)

Red Connector, ———*"

(Black Wire on Top) i?

Spacers (2 places)

Thumb Nuts (4 places)

EMI Cover Harness Connector Ground Plane

NOTE To comply with emission requirements, the Federal Communica tions Commission requires that the Video PCB Assembly be housed in the EMI Cover Do not operate this game without properly installing the EMI Cover metal spacers, and thumb nuts

Video PCB

Figure 3-4 Game PCB Removal

. Disconnect the harness connectors from the bottom of the Video PCB.

NOTE

The brass thumb nuts are easy to cross-thread. Use care when installing and tightening them.

wa . Remove one of the two thumb nuts and spacers holding the top of the Video PCB (and the bottom of the CPU PCB) to the ground plane. Loosen, but do not remove, the other thumb nut

. Remove the two thumb nuts holding the bottom of the Video PCB to the ground plane. Carefully hold the Video PCB in place to prevent the PCB from falling or causing excessive bending at the edge connector.

Remove the remaining thumb nut and spacer that was loosened in step 5. Gently disconnect the Video PCB from the CPU PCB.

Page 32

Maintena

8. Replace the Video PCB by first connecting the Video PCB to the CPU PCB edge connector. Carefully position both the Video and CPU PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb nut and spacer through both of the PCBs and into the corresponding ground plane post. Install and tighten the two thumb nuts holding the bottom of the CPU PCB to the ground plane. . Install the remaining thumb nut holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane Finger-tighten both thumb nuts holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane. . Connect the harness connector to the bottom of the Vidco PCB.

NOTE To comply with emission requirements, the Federal Communications Commission requires that the Video PCB Assembly be housed in the EMI cover. Do not operate this game without properly installing the EMI cover, metal spacers, and thumb nuts.

CPU PCB Perform the foliowing procedure to remove/replace the Central Processing Unit (CPU) PCB. (See Figure 3-4.)

NOTE Ifthe Video PCB has already been removed, disconnect the harness connectors from the left edge of the CPU PCB, then remove the two thumb nuts holding the top of the CPU PCB to the ground plane. Remove the CPU PCB.

wv

a . Turn the game power off. . Unlock and open the lower rear access panel. . Remove the four thumb nuts holding the EMI cover to the ground plane. Disconnect the harness connectors from the left edge of the CPU PCB. . Remove the four thumb nuts holding the CPU PCB (and the top of the Video PCB) to the ground plane. . Gently disconnect the CPU PCB from the Video PCB. . Replace the CPU PCB by first connecting the CPU PCB to the Video PCB edge connector. Carefully po- 10. Championship Sprint

sition both the CPU and the Video PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb nut and spacer through both of the PCBs and into the corresponding ground plane post. . Install and tighten the two thumb nuts holding the top of the Video PCB to the ground plane.

. Install the remaining thumb nut holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane.

Finger-tighten both thumb nuts holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane

Connect the harness connectors to the left edge of the CPU PCB. (See Figure 3-4 for the proper connector locations.)

Removing the Fluorescent Light Assembly

Perform the following procedure to remove/replace the fluorescent light assembly. (See Figure 3-5.)

1. Turn the game power off.

From the front of the cabinet, using a 1/8-inch hex driver, remove the three screws and washers holding the upper retainer to the top of the cabinet . Grasp the top edge of the attraction shield and the attraction film, and lift them out of the cabinet.

Disconnect the fluorescent-light harness connector.

. To remove the fluorescent tube, gently twist the tube a quarter turn and remove it from the sockets. Replace in the reverse order.

. To remove the entire fluorescent light assembly, clisconnect the light harness connector in the rear of the cabinet. Using a Phillips screwdriver, remoye the two screws holding the fluorescent light board to the cabinet. Lift the fluorescent light assembly out of the front of the cabinet. Replace the fluorescent light assembly in the reverse order of removal.

Removing the Speakers

Perform the following procedure to remove/teplace the speakers. (See Figure 3-6.)

1, Using a 1/8-inch hex driver, remove the three screws holding the rear of the speaker grille to the cabinet. . Using a Phillips screwdriver, remove the three screws holding the front of the speaker grille to the cabinet.

. Remove the speaker grille.

Page 33

Championship Sprint Maintenance

1/8-inch Hex-Head Screws Upper

Attraction @ places) Retainer

Shield p a

Phillips-Head Screws (2 places)

Fluorescent Tube

| / ! Attraction 7: Film

Fluorescent Light Assy

Fluorescent Light NS Harness Connector

Figure 3-5 Fluorescent Light Assembly Removal

Speakers

‘Speaker Grille

1/8-inch Hex-Head Screws (3 places) Phillips-Head Screws (3 places) Phillips-Head Screws (3 places)

Figure 3-6 Speaker Removal

  • Using a Phillips screwdriver, remove the four screws. holding the speaker to the cabinet. Do not let the
CAUTION speaker fall

Do not touch the speaker cones when handling 5. Lower the speaker just far enough to disconnect the the speakers. The cone material is fragile and can two speaker wires. Ensure that the speakers are propbe easily damaged. erly phased by placing the same color-coded connector on the same tab on each speaker.

  • Replace the speaker in the reverse order of removal.
Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

Chapter 4

Troubleshooting

The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist. contact your local disuibutor or your Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified service technician,
Page 36

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the schematic package supplement. The following information is intended to acquaint the service tech-

nician with the portions of these documents that contain

useful troubleshooting and repair information.

Assembly and Component Locations

The parts lists in Chapter 5 of this manual illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagrany).

Diagrams

The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.

Troubleshooting Techniques

A WARNING A

To avoid electrical shock, turn off the game power before attempting to troubleshoot this game

The following troubleshooting steps are arranged in a sequence recommended for tocating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.

Check Fuses

Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the display manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.

Localize Trouble

Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 of this manual. Championship Sprint

Visual Check

Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components

Check Individual Components

Check soldered-in passive components (¢.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry, Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.

Repair the Assembly

CAUTION Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and transistors.

Repair or replace the defective part. Refer to Chapter 3 and information in this chapter for special removal and replacement procedures, Check for proper operation of the repaired circuit.

Soldering Techniques Observe the following recommendations when removing or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components.

Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns Or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information.

A15-to 27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controlled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.

Page 37

Championship Sprint

CAUTION Solder guns are not recommended for removing or replacing soldered-in components on a printed-circuit board. Solder guns can overheat a device, and their Jatge transient voltage can damage a voltage-sensitive device.

The following additional equipment is recommended for removing and replacing soldered-in components:

  • Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multilayer PCB with plated-through holes, © Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended.

Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits

The easicst and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1, Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin ina random order. Remove the loosened pin with the tip of the soldering iron or a necdle-nose pliers as shown in Figure 4-2. Allow a moment for the PCB to cool before

Diagonal Cutter

Figure 4-1 Removing IC (Cut-Pin Method) Troubleshoourg

Needle-Nose Pliers

Soldering Iron 1

Figure 4-2 Removing IC Pins

procceding to the next pin. Apply just enough heat to remove any stubborn pins.

For a multi-layer PCB with piated-through holes, use 4 solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4

CAUTION Do not use a solder wick to remove solder from inside plated-through holes, The heat required for the solder wick to remove the soldcr from inside the hole could damage the PCB.

Use an integrated-circuit (IC) pulling tool to remove socketed ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.

Troubleshooting Static-

Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, ¢.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in 4 person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.

Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an ob-

Page 38

Troubleshooting,

TC ae :

Preferred Method im W et

Solder Sucker Soldering Iron Championship Sprint

Solder Sucker

Soldering Iron

Alternate Method

Figure 4-3 Removing Solder from Plated-Through Holes

Soldering Iron Solder Wick

Figure 4-4 Removing Solder from Lead Connection Pads

ject that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is ef-

EN ob fective when working extensively with static-sensitive devices. When soldering a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) A Slatic-sensitive device can appear defective due to leakage on a PCB. Observe the precautions for grounding, static voltages described in the preceding paragraph and clean both sides of the PCB with fiux remover or an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Page 39

Chapter 5

Illustrated Parts Lists

, -

tFaiSig

a Se

2)0la

le IS

|8RwoThis chapter provides information you need to order

moo ye TL parts for your game. Common hardware (screws, nuts,

3ig { 6i3 awashers, etc.) has been deleted from most of the parts
aLelists.
5ZThe PCB parts lists are arranged in alphabetical order by
;]?4 ¢component. Each component subsection is arranged al-
#!aFa3a1sically byesi
Pe=“ | 27]2biFa |phanumerically by reference designator.
FAaaq
(4 1 Ta} ) 4AL)Tal4Other parts lists are arranged alphanumericaliy by Atari

Hl ral 3 Ce D E F H part number. In these parts , all A-prefix numbers

—~ ol |gzrcome first. Following these are numbers in sequence eval-
550-6013all al |2)ag | 3uated up to the hyphen, namely 00- through 99-, then
33|000598- through approximately 201000-
afe~lvlWhen ordering parts, please give the part number, part
fBename, number of this manual, and serial number of your
Sawl |game. This will help us fill your order rapidly and cor-
a—|rectly. We hope the results will be less downtime and

6 2 a FS i more profit from your game x in os 1 front cover of this manual

7 2

|eo3)v33Atari Customer Service numbers are listed on the inside
xinos1front cover of this manual.

a Ld

87 : ROS5a]fe\
LJse3A]efe&rs aldalte|
8nez33S|3)Bistt
alua5a=| 3@ igs
78(7"R| AGLFOL| ffyg|g[Piet
coizeq4-0174nos"o222Su
L-On201g
get fos3we9 a“babalLad Ge asEl
it_SSeSFE——@g os
Beet 8) “Gl(ry&(Elg la 8[Be tO 22.55 ie
Poa—t3]aielsgifbe‘a!
cowsigiaofall)9Telserat
WiawekekLad SUNTotsoeEHrE
ereeee re|3
fy¢5gy eo ceo) SSBLS£93,
—}\Bfpens=]i
a|ieila ieFlj
osfrtadssz
&RELLpocoe)
/fee eye ~ gayow2225
ans(oo pypene383
10 fe ESEEGo”
cia SCea081§fF aaaoa
zet+ #G7OPP), 5tot

BUY Geosdexay ae

“3Re iEymB OR agg
38BR OB nas
{ |imrBo‘a > os
tryBas3g
coFeae23

[ crf © PS 2 7 s00ur.,|

aATARI CC) 06 ATARI system I1-CPUnTOo
Ji7J19MADE IN USA_AgY2S71
Page 40

Mlustrated Parts Lists Championship Sprint

items Not Shown 042895-01 Lael Upper Attraction Panel Retainer 042707-01 Foam Tape Attraction Shield

439012-1202 Wells-Gardner Display, or Fluorescent Light oa Assy aay 139012-1206 e Figure 5. 143729-01 AD! (Disce) Display Attraction Film with Grapnics

148007-001 043016-01 Display Bezel recteroie 042709-01 Display Shield 040936-01 H-Moiding

178013-001 Spring Draw Latch

043011-01 Lower Retainer

Control Panel Assy See Figure 5-2 See Figure 5-7

Steering Wheel Assy 171078-002 See Figure 53 Com Counter

78-3201 Adjustable Glide

Audio Il PCB Assy Foot Pedal Assy See Figure 5-11 See Figure 5-6

Figure 5-1 Cabinet-Mounted Assemblies A043725-xx C

Page 41

Championship Sprint Ilustrated Parts Lists

Items Not Shown

A043372-01 Speaker Harmess Assy

A043377-01 Display Power Harness Assy

‘A043786-01 +5V Power AC Harness Assy ‘A043705-01 Fan Cord Assy A043704-01 A043166-01 Light Harness Assy ~ +8¥ Harness Assy

] 043544-01 Ground Plane

A043703-01 034536-10 aa ey 0.62-Inch Vibration Damper Auxiliary Harness Assy \_ 7 ENE = , Ti ee : p ® Aosg7p2-07 ZA LaCie 7 CPU PCB Assy Secondary Power Harness Assy See Figure 59

034536-11 0.8 1-Inch Vibration Damper A043708-01 Cabinet Control Harness Assy

A038881-01 A043785-xx _ Lock Assy +5V Power Supply Assy

Video PCB Assy A043169-01 See Figure 5-10 Video Harness Assy

043148.01 ‘040547-01 EMI Cover Fan Assy

(043123-01 Rear Door Panel A043787-xx 10 Amp Power Supply Assy See Figure 55 <> A040699-01 COD On/Off Switch Assy A043105-01 SS Cabinet Assy

040036-01 Power Cord Plate A040586-01 Power Cord Assy

Figure 5-1 Cabinet-Mounted Assemblies, Continued A043725-xx C

Page 42

Illustrated Parts Lists Championship Sprint

Cabinet-Mounted Assemblies Parts List

Part No. Description

A000598.09 Steering Wheel Assembly AQ3 8881-01 Lock Assembly for Rear Panel A040547-01 Fan and Bracket Assembly (70 CFM); Acceptable substitute is part no. A040547-02 A040586-01 Power Cord Assembly A040699-01

A042701-01 A043105-01 A043166-01 A043169-01

A043372-01

A043661-01 A043692-01

A043702-01 A043703-01 A043 704-01 A043705-01

A043708-01 A043 7324-01 A043735-01 A043 785-01

A043786-01 A043787-01 78-4201 78-6990402

034536-10 034536-11 038091-01 040036-01

040936-01 042707-01 042709-01 042715-01

042895-01 043011-01 04301601 043123-01

043148-01 043544-01 043729-01 139012-1202 439012-1206

148007-001 171078-002 178013-001

T™M-279 TM-281 On/Off Switch Assembly with Harness

Fluorescent Light Panel Assembly Cabinet Assembly $V Harness Assembly Video Harness Assembiy Speaker Harness Assernbly Display Power Harness Assembly ‘Audio II PCB Assembly Control Panel Assembly Secondary Power Harness Assembly Auxiliary Harness Assembly Fluorescent Light Harness Assembly Fan Cord Assembly

Cabinet Control Harness Assembly Video PCB Assembly CPU PCB Assembly 5 V Power Supply Assembly (Acceptable substitutes are part numbers A043785-02, -03, and 04)

5 V Power AC Hamess Assembly 10 A Power Supply Assembly (Acceptable substitutes are part numbers A043787-02, -03, -04, -05, and -06) Adjustable Glide 1/4-Inch x 1/8-Inch Foam Tape (72 inches required; used on inside lips of both retainers) 0.62-Inch Thick Vibration Damper 0.81-Inch Thick Vibration Damper Molded Coin Box Power Cord Plate

H-Molding Attraction Shield Display Shield Speaker Griile Upper Attraction Panel Retainer Lower Attraction Retainer Display Bezel Rear Door Panel

EMI Cover Ground Plane Attraction Film with Graphics Wells-Gardner 19-Inch Color Raster Display OR ADI (formerly knewn as Disco) 19-Inch Color Raster Display 5-Inch Round, 8, Speaker Non-Resettable Coin Counter, 12 VDC Spring Draw Latch

The following are technical information supplements for this game: ADI (formerly known as Disco) 19-Inch Color Raster Display Manual OR Wells-Gardner 19-Inch Color Raster Display Manual System II/Championship Sprint Operators Manual Championship Sprint Schematic Package Championship Sprint Self-Test Label Cheek the Colors in Your System II” ADI Medium-Resolution Video Display

Page 43

Championship Sprint iasteated Parts Lists

Steering Wheel Assy See Figure 5-3 043563-01 178030-003 Spacer Button Assy 043463-01 160013-001 Bow Washer Leaf Switch with Button Holder 85-23F 110 75-9910NO Screw Stamped Nut

043728-01 Cortroi Panel Decal

043461-01 Contral Panel Weldment

a On A043709-01 75-010F Harness Assy Flat Washer 82-8116B Screw 75-050B Lock Washer

Figure 5-2 Control Panel Assembly A043692-01 A

Control Panel Assembly Parts List

Part No. Description

A000598-09 Steering Wheel Assembly A043709-01 Control Panel Harness Assembly 75-0\0F #10 Black Flat Washer 75-050B #10 Black Internal Tooth Lock Washer

75-99 10NO #11 5/8:Inch Stamped Nut 82-81 16B #10-24 x \-Inch Black Button-Head Hex Socket Machine Screw 85-23F110 #10-24 x 5/8-Inch Type F Hex Washer-Head Screw 043461-01 Control Panel Weldment

Bow Washer Spacer 043728-01 Control Panel Decal 160013-001 Leaf Switch with Button Holder 178030-003 Black Button Assembly

5-5

Page 44

Mlustrated Parts Lists Championship Sprint

78-40104 72-0398 Steering Wheel Lock Washer

175005-004 Flat Washer

000599-02 Logo Cover

72-5416X Bolt

i

72-8512 | Screw | a 76-092020 Thompson Bearing

750128

  • Washer
  • 75.055B a Lock Washer 000605-01 Housing 76-091010 Thompson Bearing

72-5512 Bolt A035220-02 Coupler PCB Assy

85-22F206 000616-01 Sorew 75-07002 Encoder Hub Washer

Figure 5-3 Steering Wheel Control Assembly A000598-09 AB

5-6

Page 45

Championship Sprint lustrated Parts Lists

Steering Wheel Control Assembly Parts List

Past No. Description

A035220-02 Coupler PCB Assembly 72-0398 3/8-Inch External Steel/Zine Lock Washer 72-5410X 3/8-16 « 1-Inch Steel/Zinc Hex-Head Bolt 5512 1/4-20 x 3/4-Inch Steel/Zinc Hex-Head Bolt

1/4-20 x 3/4-Inch Socket Head Cap Screw #2 Flat Plain Washer 1/4-Inch Internal Tooth Lock Washer 1/4-Inch Special Flat Washer

76-09 1010 Type-10L10-FK Thompson Bearing 76-092020 Type-201.20-FK Thompson Bearing 78-40104 10-Inch Steering Wheel 85-22F206 #2.56 x 3/8-Inch Cross-Recessed Pan-Head Machine Screw

000599-02 Atari Logo Cover 000005-01 Housing 00061601 Encoder Mub 043788-01 Shaft 107013-001 Light Oil Lubricant 175005-004 406 1... 4.25 O.D., 16-Gauge Thick Steel/Zine Flat Washer

w “4

Page 46

Ilustrated Parts Lists Championship Sprint

142028-001 Transformer A037540-01 Ground Jumper Assy '

99-11003 Starter 89-11009 Starter Socket

A005493-01 Oss i; Harness Assy

179035-001 Light Holder

041981-01 Light Bracket 70-304 Fluorescent Light

Figure 5-4 Fluorescent Light Panel Assy A042701-01 B

Fluorescent Light Panel Assembly Parts List

Part No. Description

A005493-01 Fluorescent Light Harness Assembly 037540-01 Ground Jumper Assembly 70-304 18-Inch, 15 W Fluorescent Light 72-6408S #4 %-Inch Pan-Head Self- Tapping Screw 79-561816P Wire Nut

99-11003 Starter 99-11006 Retaining Clip (consists of two pieces) 99-11009 Starter Socket 041981-01 Light Bracket

042740-01 Light Panel 142028-001 60 Hz Ballast Transformer 176015-108 #10 x %4-Inch Cross-Recessed Pan-Head Screw 179035-001 Light Holder ree

Page 47

Cd Championship Sprint

N Illustrated Parts Lists

S

5-9

Page 48

Ilustrated Parts Lists ‘Championship Sprint

WARNING A Not Shown This 5-volt switching power supply may not A043785-04 have a shield asillustrated below. The power Sierracin 5V Power Supply Assy supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have turned off the power to the game

72-HA4606S 149003-xxx Screw 5V 10 Amp Switching Power Supply Assy

A043367-xx 179231-002 Jumper Assy Terminal Block =) g

A043367-xx Jumper Assy

A043366-01 5V Harness Assy 142042-001 Transformer

72-HA4806S Screw

043396-01 Power Supply Chassis Base

A042384-01 Line Fiter Assy

46-2013002 Fuse

037640-01

Warning Label

179225-2205, or 79-3206 Fuse Block

Fuse Block Cover

043622-01 Fuse Label 46-2012002 Fuse

Figure 5-5 Power Supply Assemblies Switching/Linear (SL) Power Supply Assembly A043787-xx A

5-10

Page 49

Championship Sprint iustrated Parts Lists

Switching/Linear (SL) Power Supply Assembly Parts List

Part No. Description

A042384-01 A043366-01

46-2012002

46-2013002 72-HA4606S 72-HA4806S, 034544-01

037640-01 043396-01 043622-01 142042-001

149003-xxx 176017-006 179225-2205 79-3206 179231-002 Line Filter Assembly 5 V Harness Assembly Jumper Assembly 250 V Slow-Blow 2 A Fuse

250 V Siow-Blow 3 A Fuse #0-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw #8-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw Fuse Block Cover

Power Supply Warning Label Power Supply Chassis Base Power Supply Fuse Label Transformer

5 V 10 A Switching Power Supply Assembly #M3 x 6 mm Stainless Steel Machine Screw 5-Position Fuse Block OR 5-Position Fuse Block 2-Position Terminal Block

Sierracin 5-Volt Power Supply Assembly A043785-04 A Parts List

Part Description

99-207001 99-207002 99-207003 99-207004

99-207005 99-207006 99-207007 99-207008,

99-207009 99-207010 99-207011 99-207012

99-207013 99-207014 99-207015 99-207016

99-207017 99-207018 99-207019 99-207020

99-207021 99-207022 99-207023 99-207024

99-207028 Chassis Stiap, Small Black Cable Box, #172 Indestructible Assembly, PCB Diode, 100 A, 1N4002 Diode, 100 V, 3 A, Standard Recovery Thyristor, SCR, Sens Gate, 30 V. 4 A, TO220AB Diode, Zener, 6.2 V, 400 mW, IN753A

Regulator, 723 Standard DIP Voltage 3055 Transistor, 75 W, NPN, SEL, TO-220 2N2219A Transistor, NPN, TO-5 Capacitor, Electrolytic, 220 Q, 16 V, Radial Capacitor, Electrolytic, 10 kQ, 16 V, Axial Capacitor, Poly Film, .0047 pF, 100 V Resistor, 1000, +5%, 4 W, Resistor, 1 kQ, £5%, 4 W

Resistor, 1.5kQ +5%, 4 W, Resistor, 4.7 kQ +5%, 4 W, Resistor, 8200 +5%, 4 W, Potentiometer, 500 Q, + 20%, 2 W, Horizontal

Resistor, Metal Oxide, .10 0, 2 W, Tie Mount, PCB, TM-35B-M Cable Suap, Medium Black Terminal, Swage Double Turret Terminal, Swage Double Turret Standoff, 4-40 x .200 Threaded Fabrication, 2.43 x 4.85 PCB Transformer

Page 50

Iustrated Parts Lists Championship Sprint

043691-01 Spring

043746-01 in 2 places Pedal Frame (in each pin slot)

043750-01 Foot Pedal Link

043749-02 ies 043749-01 Foot Pedal : Foot Pedal Satety Tread (Lett) be are Safety Tread (Right)

043747-01 Double Pedal (Left) Doubie Pedal (Right)

In 6 places (under each bearing) 043748-01 Pedal Shaft

A043710-01 Foot Pedal Harness Assy

19-9026 ——_478012-006 Potentiometer Retaining Ring i ei Flat Washer 175005-003.

Figure 5-6 Foot Pedal Assembly A043745-01 B

Page 51

Championship Sprint

Foot Pedal Assembly Parts List Mlustrated Parts Lists

Part No. Description

A043710-01 19-9026 72-8808 75-9188

76-080802 043691-01 043746-01 04374701

043747-02 043748-01 043749-01 043749-02

043750-01 107027-001 475005-003, 178012-006 Dual Foot Pedal Harness Assembly 5 kQ2 Potentiometer with Hex Nut and Lock Washer #8-32 « ¥-Inch Hex Socket-Head Cap Screw #8-32 Sieel Cadium Hex Machine Nut

¥e-Anch 1.D. x 1/8-Inch Bearing (Nyliner) Pedai Return Spring Pedal Frame Double Pedal (Right)

Double Pedai (Left) Pedal Shaft Foot Pedal Safety Tread (Right) Foot Pedal Safety Tread (Left)

Foot Pedal Link Multi-Use Lithium-Base Lubricant -60 Thick .505 1.D. 1.00 O.D. x %-Inch Flat Washer Ys Inch Diameter Shaft Retaining Ring,

Page 52

Championship Sprint Hlustrated Parts Lists

99-10140 Panel Assembly 75-948S 2 Locknut a

99-10152 Right Coin inlet ov 99-10147 Harness 171006-035, Coin Mechanism

75-9448 ‘Locknut

99-10096 Fastener

99-10151 Left Coin Iniet

99-10080 Lamp Socket

99-10105, Bar 72-9406S Screw

99-10104 Bar Retainer

99-10042 thru 99-1045 010158 Coin Switch Assembly

Bracket Assembly

99-10153 Coin Return Box 99-10150 Switch Cover 99-10068 Coin Chute 65-441C Coin Switch _~ 99-10075 thru 99-1078 Switch Wires 99-10008 Retainer 7544125

Screw

Figure 5-7 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 53

Championship Sprint Ilustrated Parts Lists

99-10148 Lock Assembly

99-10142 Button Housing

72-HA1404C Screw

99-10134 99-10119 Cover 99-10139 > CoinDoor 7 Button Assembly | 9940118 7 Button.

/ 99-1015, 99-10148 Spring Lock Assembly HS

wa e Ae A H Uo MA hn 99-10141 Pa 5 Coin Return Cover Hi § % | | 99-0117

, Coin Return Door

72-JA1405B Screw <— _99-10144 Channel Clip

99-15066 Screw

99-10149 Service Door

038091-01 Coin Box

99-10143 Frame

[ NOTE Acceptable alternate or substtute coin door assembly is part number 17 1034-001

Figure 5-7 Coin Acceptors, Inc. Coin Door Assembly, Continued. 171027-001 A

Page 54

Illustrated Parts Lists Championship Sprint

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part Description

65-441 70-11-47 72-9406S 72-HA1404C

72-JA1405B 75-1412S 75-9945, 99-10008

99-10042 99-10043, 99-10044 99-10045,

99-10068 99-10075 99-10076 99-10077

99-10978 99-10080 99-10081 99-10096

99- 10104 99-10105, 99-10115. 99-10116

99-10117 99-10118 99-10119 99-10134

99-10139 99-10140. 99-10141 99-10142

99-10 99-10144 99-10147 99-10148

99-10149 99-10150 99-10151 99-10152

99-10153 99-10154 99-15066 171006-035 Coin Switch Miniature Bayonet Lamp #4-40 x 3/8-Inch Truss-Head Screw #4-40 x 1/4-Inch Pan-Head Screw

#4-40 x .31-Inch Pan-Head Screw #4-40 x 3/4-Inch Pan-Head Screw #4-40 Locknut Retainer

Coin Switch Assembly for Belgium 5 Frand U.S. $.25 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss | Fr Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P

Coin Return Chute Switch Wire (included in coin switch assembly 99-10043) Switch Wire (included in coin switch assembly 99-10042) Switch Wire (included in coin switch assembly 99-10044)

Switch Wire (included in coin switch assembly 99-10045) Lamp Socket Key Holder Fastener

Bar Retainer Bar Spring Plastic Coin Return Lever

Steel Coin Return Door Amber Coin Return Button Amber Coin Button for U.S. $.25 Coin Button Cover

Coin Door Coin Door Inner-Panel Assembly Die-Cast Coin Return Cover Die-Cast Button Housing

Coin Door Frame Channel Clip Harness Lock Assembly

Service Door Switch Cover Left Coin Inlet Right Coin inlet

Coin Return Box Bracket Assembly Screw for Clamp Metal Coin Mechanism for U.S. $.25

5-16

Page 55

Championship Sprint Ulustrated Parts Lists

N O T E i)

5-17

Page 56

Illustrated Parts Lists

NOTE To comply with emission requirements, the Federal Communications Commission requires that the Video PCB Assembiy be housed inthe EMI cover. Do not operate this game without properly instaling the EM) cover, metal spacers, and thumb nuts.

CPU PCB Assy See Figure 5-9

Video PCB Assy 475481.6802 See Figure 5-10

72-1612S Screw (2 places)

043148-01 EM! Cover

177018-206 Thumb Nut Spacer 72-1610F Screw

Lock Washer Championship Sprint

75-058 Lock Washer

043143-01 Ground Plane

034536-10 0.62 Foam Pad

76015-110

75-058 Lock Washer

034536-11 0.81 Foam Pad

Figure 5-8 PCB Mounting Hardware

Page 57

Championship Sprint

PCB Mounting Hardware Parts List Mustrated Parts Lists

Description

75-058, 034536-10 03453611

04354401 043148-01 176015-110 177018-206 178181-6802 Video PCB Assembly CPU PCB Assembly #6-32 x 5/8-Inch Pan-Head Screw #0-32 x 4-Inch Pan-Head Screw

#8 Internal Tooth Lock Washer 0.62-Inch Foam Vibration Damper 0.81-Inch Foam Vibration Damper

Ground Plane EMI Cover 10 x 5/8-Inch Cross-Recessed Pan-Head Screw #6-32 Knurled Brass Thumb Nut Round Sp:

Page 58

Championship Sprint Ilustrated Parts Lists

woo WT oo ree wu 20g masa —

fart atl

eT ‘shest a 2 i, Cc oe i a)

tobe 3 od a fp pacer vn a ehalet | [eS se ACN DaRK-GHOTET its Riese aa Ft ERR — ; = oo eS i Tho -svoser

Lora FaXX-GHOSET daxx-shoset

Boog

{ soour,f 39 ua om

ATARI CC) 86 ATARI SYSTEM IT MADE_IN USA, eov-enEt E187 7 Racal cial “RETEST wis Care i ERR-SROVET j ‘92xX-ShOSET é

so ee _— F, = eve SS n u {sn08 Cam (es a Ge el 3 = we 10 cues ° WaXK-SHODET 4

~ on bt TOU-2Oh2ET nZEWT ast Ger? Sas! 50 Csr 4 . a # Caer? Gao eet 4 BWeieT rst — Z LL w —_ ad Geer Cees aami-sioser aa pazeT o> vo BE cc; eo > a wee ‘CETST oe nies io o> a. eS ow R 008 5 nos ter FA

kTux-ss09e7 iar emi ic 38 ‘Gi as [ q CESTST one sney | 200-BOELET " j « eno9e Sih BBE ion —— BTXX-GhOdET. ‘ a a a cue i] f : 1) gy | : MB rar Fi L veTST a Ff gE eb i a? $ g = BO o> co) 3 8 Bye Shis ee cost y

  • ex) a AT it _ { (at fara Fin dill ith S aa w m wage n 5 . 33

J19 Ja7 AowZ571

Figure 5-9 Central Processing Unit (CPU) PCB Assembly A043735-01 A

5-20

Page 59

Championship Sprint Ilustrated Parts Lists,

Central Processing Unit (CPU) PCB Assembly Parts List

DesignatorDescriptionPart No.

The following set of four ICs is used in the German Championship Sprint CPU PCB only:

OFIntegrated Circuit, EPROM. Type-27256. 300 ns136045-x2.
ONIntegrated Circuit, EPROM, Type-27256, 300 ns136045-x2
TLIntegrated Circuit, EPROM, Type-27128, 300 ns1360:
7Integrated Circuit, EPROM. Type-27128, 300 ns136045-x227

Integrated Circuits

1AIntegrated Circuit, Tvpe-611613721 1-001
IB/CIntegrated Circuit, Type-G1 16137211-001
IDIntegrated Circuit, Type-2804-3 EEPROM137329-300
1EIntegrated Circuit, Type-7437-74L832

inf Integrated Circuit, Ty] IK Integrated Circuit, Type- IL Integrated Circuit. Type-74 IM Integrated Circuit, Type-

INIntegrated Circuit, Type-7418244AT-TALS244
IpIntegrated Circuit, Type-74L$24437-T4LS244
IRIntegrated Circuit, Ty37-74832
IsIntegrated Circuit, Ty, pe- ADC0809137243-001
2BICIntegrated Circuit, EPROM, Type-27128, 300 ns136045-x118
2DIntegrated Circuit, EPROM, Type-27128, 300 ns136045-x119

2D/E 37-74LS04 2F 37-74LS244

2Integrated Circuit, Type-T11 (DCTII-XA)137361-002

2L Integrated Circuit, Type-74L$174 i 2M Integrated Circuit, Type-741 2N Integrated Circuit, Type-74L:

2P Integrated Circuit, Type-74LS670 BE Integrated Circuit, Type-74LS138 BF Integrated Circuit, Type-74LS161 3H Integrated Circuit, Type-741.800

3y Integrated Circuit, Typ aK Integrated Circuit, Ty 3L Integrated Circuit, Type-7487 3M Integrated Circuit, Type-74L$138

3N Integrated Circuit, Type-74L874 3P Integrated Circuit, Type-74874 3R Integrated Circuit, Type-74L520 4A Integrated Circuit, Type-74L8244

4A/B Integrated Circuit, Type-74L8244 4BIC Integrated Circuit, Type-74LS139 4c/D Integrated Circuit, Type-741S74 4D Integrated Circuit, Type-74LS 163A.

4E Integrated Circuit, Type-74L8138, aE Integrated Circuit, 4H Integrated Circuit, Ty 4y Integrated Circuit. Type-74Ls

“in the part number denotes the revision level

Page 60

Mlustrated Parts Lists

Central Processing Unit (CPU) PCB Assembly Championship Sprint

Parts List, Continued

DesignatorDescriptionPart No.
4KIntegrated Circuit, Type-741.$37337-T4LS373,
4LIntegrated Circuit, Type-74L8138137177-001
4MIntegrated Circuit, SLAPSTIC137412-109
4NIntegrated Circuit, Type-74L8245,37-74LS245,
4PIntegrated Circuit, Type-74L824437-74L8244
5BIntegrated Circuit, Type-6502A90-6013
5DIntegrated Circuit, Type-74L824537-74LS245
SEIntegrated Circuit, Type-74L837437-74L8374

SF Integrated Circuit, Type-74LS175 5H Integrated Circuit, Type-74LS245

  • Integrated Circuit, Type-74LS08. 5K Integrated Circuit, Type-74L804

SL Integrated Circuit, Type: 5M Integrated Circuit, Type-7: 5N Integrated Circuit, Type-74L8174 5P Integrated Circuit, Ty] 4LS244

OB Integrated Circuit, POKEY

oDIntegrated Circuit, Type-74L824537-74L8245,
OEIntegrated Circuit, Type-74L$374.37-74LS374
OFIntegrated Circuit, EPROM, Type-27256, 300 ns136045-X125
6KIntegrated Circuit, EPROM, Type-27256, 300 ns136045-x124
6L.Integrated Circuit, EPROM, Type-27256,300 ns
ONIntegrated Circuit, EPROM, Type-27256,300 ns

OR Integrated Circuit, EPROM, Type-27256, 300 ns

6SIntegrated Circuit, EPROM, Type-27256, 300 ns136045-x120
7Bintegrated Circuit, POKEY€012294-01
7DIntegrated Circuit, Type-TMS5220C137308-002
TFIntegrated Circuit, Leta137304-1001
7HIntegrated Circuit, Type-74L!37-74L874
7Integrated Circuit, Type-74LS1037-74L810
7KIntegrated Circuit, Type-6116137211-001
7LIntegrated Circuit, EPROM, Type-27128, 300 ns136045-x126
7NIntegrated Circuit, EPROM, Type-27128, 300 ns136045-x127
7PIntegrated Circuit, Type-6116137211-001
TRIntegrated Circuit, Type-74LS16137-7418161
8BIntegrated Circuit, Type-74LS16137-74L8161

8C Integrated Circuit, Type-74L: Ls. 8D Integrated Circuit, Type-74L: ALS

8FIntegrated Circuit, Type-74L824437-74LS244
8HIntegrated Circuit, Type-Y2151137401-001
8y/KIntegrated Circuit, Type-YM4012137402-001
8NIntegrated Circuit, Type-74S0437-74804
OBIntegrated Circuit, Type-LF1320!137352-001
9CIntegrated Circuit, Type-LF13201137352-001

9D Integrated Circuit, Type-LF13201 ODIE Integrated Circuit, Type-LF13201

“x” in the part number denotes the revision level

5-22

Page 61

Championship Sprint

Central Processing Unit (CPU) PCB Assembly Parts List, Continued Illustrated Parts Lists

DesignatorDescriptionPart No.

Oy Integrated Circuit, Type-LM324 oLM Integrated Circuit, Type-LM324

10BIntegrated Circuit, Type-LM324:
locIntegrated Circuit, Type-1.M32437-LM324
10FIntegrated Circuit, Type-LM32437-LM324
10L/M,Integrated Circuit, Type-TLO82CP37-TLO82CP
11MIntegrated Circuit. Type-74C04137309-001

Sockets Socket, Medium-Insertion-Force, 16-Pin 79-42C16 Socket, Medium-Insertion-Fotce, 20-Pin 2€20 Socket, Medium-Insertion-Force, 24-Pin 79-42C24 Socket, Medium-Insertion-Force, 28-Pin 79-42C28 Socket, Medium-Insertion-Force, 40-Pin 79-42C40

Capacitors C1-C60 1 KE SOV 122002-104

C31-CO0,Capacitor,°F, SOV122002-104

C80 c8l C82-C89 C90

col C92 C93 Co4

COS C96 COT C98-C100

col C102 C103-C 109 C110

ciil C12 C13. C1ls. Capacitor, Ceramic, .018 nF, 50 V Capacitor, Ceramic, .22 nF, 25 V

actor, Ceramic, .1 pF, 50 V acitor, Ceramic, .1 pF, 50 V Capacitor, Mica, 100 pK, 100 V Capacitor, Mica, 39 pE, 100 V

capacitor, Ceramic, .1pk, 50 V xicitor, Mica, 39 pE, 100 V “apacitor, Mica, 100 pE, 100 V Capacitor, Ceramic, .01 uF, 25 V

, OO] WE 50 V » 001 BE 50.¥ . 1 pk 50-V pacitor, Ceramic, 22.25 V

Capacitor, Tantalum, 10 uF, 20 V

Capacitor, Mica, 220 pk. 100 V Capacitor, Mica, 220 pF, 100 V

Capacitor, Ceramic, .0027 uF 50 V Capacitor, Tantalum, 10 aE, 20 V Capacitor, Ceramic, .0027 wE, 50 V Capacitor, Ceramic, .1 #E, 50 V

Capacitor, Aluminum, 10 uF 35. V Capacitor, Aluminum. 10 l Capacitor, Ceramic, .1 gE, 50V Capacitor, Ceramic, 01 wk 25 V

Capacitor, Ceramic, .01 #E, 25 V Capacitor. Ceramic, .1 pF. 50 V Capacitor, Ceramic, .1 pF, 50 V Capacitor, Mica. 220 pF, 100 V 12200:

122002-104 122002-104

122002-104 128002-390 128002-101 122005-103

122002-102 122002-102 122002-104 12200: 4

29-046 122005-103 128002-221

122015-272 122002-104

122002-104 122005-103

122005-103, 122002-104 122002-104 128002-221

Page 62

Mlustrared Parts Lists

Central Processing Unit (CPU) PCB Assembly Parts List, Continued Championship Sprint

DesignatorDescriptionPart No.
C116Capacitor, Mica, 220 pF, 100 V128002-221
cl?apacitor, Ceramic, 01 wR 25 V122005-103
C18.Capacitor,001 pF, 50 V.122002-102
ClioCapacitor, Ceramic, .001 pF, 50 V122002-102
C120Capacitor, Ceramic, .01 aE, 25 V122005-103
C121Capacitor, C1 we Sov122002-104
122Capacitor,Ceramic, .22 pk, 25 V122004-224

C123 Capacitor, Ceramic, 22 ¢F, 25 V.

C124 Capacitor, Mica, 470 pE 100 V C125 Capacitor, Mica, 470 pF, 100 V C126 Capacitor, Ceramic, .22 uF, 25 V C127 Capacitor, Ceramic, .22 pF, 25V

C128Capacitor, Ceramic, .1 pF, 50 V122002-104
C132Capacitor, Ceramic, .1 ¢F, 50 V122002-104
C133,Capacitor, Ceramic, .1 aF, 50 V122002-104
C134Capacitor, Ceramic, .22122004-224

C135 Capacitor, Aluminum, 4 C136 Capacitor, Aluminum, Hl 7

C138Capacitor, Ceramic, .1 uF 50 V122002-104
C139Capacitor, Auminum, 100 pF, 35 V24-350107
C140Capacitor, Aluminum, | pF 50 V24-500105
cl4lCapacitor, Ceramic, .1 pF, SC122002-104
C143Capacitor, Ceramic, .1 wF, 50 V122002-104
Cl44Capacitor, Ceramic, .0027 pF 50 V122015-272
clas,Capacitor, Ceramic, .0012 pF 50 V122015-122
C146Capacitor, Ceramic, .0039 gE 50 V122015-392

C147 Capacitor, Ceramic, .0068 pF, 50 V c148 Capacitor, Ceramic, .1 pF, 50 V

C149~C152Capacitor, Ceramic, .1 ¢F, 50 V122002-104

Diodes

CRI1-CR3Diode, Type-1N10031-1NL00
CR4Diode, Type-1N400131-1N4001
CRSDiode, Type-1N490131-1N4001
CRODiode, Light-Emitting, Type-MV505338-MV5053
CRTDiode, Type-1N400131-1N4001

Connectors and Fasteners

ysConnector, Header, 17-Circuit, .100 cur179118-017
J16Connector, Header, 5-Circuit, .100 ctr179118-005
J20Connector, Header. 9-Circuit, .156 ctr, pol179014-009
Jlo2, J103Connector, Header, 1 1-Circuit, .100 ctr179118-014
J106Connector, Header, 11-Circuit, .100 ctr179118-011
P18Connector, Card Edge, 80-Circuit (40 x 2)179221-180

Ql, @ Fastener, Nylon, Snap-in Q9, Q10 Fastener, Nylon, Snap-in

VRIFastener, Nylon, Snap-In81-4302

Terminal, Fast-On Tab (Acceptable substitute is part number 17905 1-002

5-24 920670-01)

Page 63

Championship Sprint

Central Processing Unit (CPU) PCB Assembly Parts List, Continued Iliustrated Parts Lists

DesignatorDescriptionPart No.

Inductors

UlInductor, 33 #6H141016-007
L2Inductor, 100 pl141002-001

Transistors

QL. Q2Transistor, 2N604434-2NO044
Q3. Q4Transistor, 2N390633-2N3906

Q5-Q8 Transistor, 2N3904 2N3904 QU. QI2 Transistor, 2N3904 2N3904

Resistors

RI2 R13-R20 R21-R23 R24. R27

R28-R33 Ra4 R35 R36

R37 RA8-R42 R43-R58 R59

ROU-ROT ROS ROO R70

R71 R R75, R76-R85, R74

R86 R87 R&8, R89 ROO

R91 R92 ROS ROW

ROS R96 ROT ROS Y WOK A, 45% Resistor, Resistor, Resistor, Resistor,

¥, 100Q. 5% ,IKQ, 45% Resistor, Resistor, 4 W, 4.7KQ, + 5%

Resistor, % W, 470 Q, + 5% Resistor, 4 W, 10K Q, + 5% Resistor, 4 W. 1K Q, 45% Resistor, 4 W. 2209, +5%

Resistor, Resistor, ¥ Resistor, Resistor, ¥

Resistor. Resistor, 4 + Resistor, 4 W, 1.8K Q. + 5% Resistor, 4 W, LOK Q, + 5%

Resistor, “4 W. 5.0K Q. +5 Resistor, 4 W. 100K Q, +5% IKQ, +5% Y, LOK Q, 43%

Resistor, Resistor, Resistor. ¥ Resistor. 4

Resistor. “4 Resistor, Resistor, Resistor,

Resistor, 4 W, 47K Q. + 5% Resistor, % W, 100K 2. + Resistor, \ Resistor, 1 10000-103 110000-102 110000: 110000-472

110000-471 110000-101 110000-102 110000-472

11 0000-47 1 110000-1034 110000- 102 110000-221

110000-221 11L0000-102 110000-103 110000-102

110600-332 110000-102 110000-182 110000-1034

110000-562 110000-104 110000-102 110000-103

110000-221 110000-221 110000-103 110000-101

110000-472 110000-101 110000-472 110000-223

1 10000-473 110000-104 110000-223 110000-473,

5-25

Page 64

Illustrated Parts Lists

Central Processing Unit (CPU) PCB Assembly Parts List, Continued. Championship Sprint

DesignatorDescriptionPart No.
R99Resistor, 4 W, 100K Q, +5%110000-104
R100Resistor, 4 W, 22K Q, + 5%110000-223
RIOLResistor, 4 W, 47K Q, +5%110000-473
R102Resistor, 4 W, 100K Q, +5%110000-104
R103Resistor, 4 W, 100K Q.110000-104
R104, R105Resistor, 4 W,1KQ, +110000-102
R106Resistor, %4 W, 100K Q,110000-104
R107, R108Resistor, 4 W, 18K Q, + 5%110000-183
R109Resistor, 4 W, JOOKQ, +5%110000-104
R110Resistor, 4 W, 3909, +5%110000-391
R111Resistor, 4 W, 5602, + 5%110000-561
R112Resistor, 4 W, 1K Q, +5%110000-102
R113Resistor, 4 W, 5.6K Q, +5%110000-562
R114Resistor, 4 W, 10K Q, +5%110000-103
R115, R116Resistor, 4 W, 1K Q, +5%110000-102
RITResistor, % W, 4709,5%110000-471
R118Resistor, 44 W, 4709, +5%110000-471
R119Resistor, 4 W, 470K Q, +5%110000-474
R120-R124Resistor, 4 W, 100K Q, + 5%110000-104
R125Resistor, 4 W, 2.2K Q, +5%110000-222
R126, R127Resistor, 4 W,4.7KQ, +5%110000-472
R128Resistor, 4 W, 2.2K 9, +5%110000-222
R129Resistor, 4 W, 100K Q, +5%110000-104
R130Resistor, 4 W, 47K Q, £5%110000-473
RI3Z1-R133,Resistor, 4 W, LOOK Q, + 5%110000-104
R134Resistor, 4 W, 47K Q, +5%110000-473,
R135-R138Resistor, 4 W, 00K 2, £5%110000-104
R139Resistor, 4 W,47KQ, £5%110000-473
R140Resistor, 4 W, 68K Q, +5%110000-683
R141, R142Resistor, “4 W, 47K Q, + 5%110000-473
R143Resistor, 4 W, 68K Q, +5%110000-683
R144Resistor, 4 W, 47K Q, +5%110000-473
R148, R151Resistor, 4 W, L00KQ, + 5%110000-104
R155, R156Resistor, 4 W, 4709, +5%110000-471
RIS7Resistor, 4 W, 10K Q, +5%110000-103
R158, R159Resistor, 4 W, 3.3K Q, 45%110000-332
R160Resistor, 4 W,1KQ, +5%110000-102
R161Resistor, 4 W, 1509, + 5%110000-151
R162Resistor, 4 W, 10K Q, +5%110000-103
R163Resistor, 4 W, 3.3KQ, 5%110000-4
R164, R166Resistor, 4 W, 1KQ, +5%110000-102
R168Resistor, 4 W,1K9, +5%110000-102
R169, R170Resistor, 4 W, 4.7K, +5%110000-472
RI71Resistor, 4 W, 2702, 5%110000-271

5-26

Page 65

Championship Sprint Illustrated Parts Lists

Central Processing Unit (CPU) PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
R172Resistor, 4 W, 129, 45%110000-123,
Ri73Resistor, % W,56Q, +11 0000-563
R174Resistor, & W, LOK ®, + 5%110000-103
R175Resistor, “i W, 8.22, +5%110000-822
RIG,Resistor, 4 W, 3.9K Q, +£5%110000-392
RIT?Resistor, va W02, 45%110000-47 1
RI78Resistor, 4 W, 1KQ, +5%110000-102,
R179Resistor, 4’ W,0Q, +5%110G05-001
RNIL, RN2Resistor Network, SIP, LOK x 8, L'8 W118002-103

Miscellaneous

VRLVoltage Regulator, Type-790537-7905
YICrystal, 20 MHz144000-003
y2|, 14.318 MHz90-101
516A8-Position, DIP16003 1-008
GA, 8-Position, DIP16003 1-008

5-27

Page 66

5-28 A043734-01 A 10 Video PCB Assembly Figure 5. a x a ise Rass idisr

gt Be S199 Bon 3ee¥s-KeT he .sis7

EER IERTTE

  • ea & 9188 ] bi16P-3 1167-3 5

o OR

"Sg 9188 PETIT Fare 1167-3 sisgp-a 5

oy ait if

9109 an, 3085-3 «TRONS KAT ferry po feat

mg a, as ont wees eee

RGSS

a wo __FL_] go

“> eos

kgzee ferry for Laney

set, 1 4) a

a dre Mary FETE s | Brcireitty yd aensaoas g arg uszea user3 9153 sre py ay re Foo ss. ool

Taens-0az Feat) mom Taps 3 oo Fi

5273 o 1

FECTED a, 9

Oo ih ese ves aeoys-xKa7 ~ *

NOTE:

  • DO NOT INSTALL R3 AND C143.
  • MODIFICATIONS TO ASSEMBLIES USING 042038-01 REV AAND-

BPC BOARDS:

« LIFT PIN 15 OF IC 9K.

  • ADD JUMPER BETWEEN 9K PAD 5 AND 9F PAD 1.
  • ADD JUMPER BETWEEN SF PAD 2 AND 9K PAD 15. CONFIDENTIAL, Reprodu conditionally issued, and ‘or any design or technicad inform: vendors of Aian Games Corporation, and for manufacture und ‘or the subject matter thereat, uniess by writen agreement with Iustrated Parts Lists Championship Sprint
Page 67

Championship Sprint Ilustrated Parts Lists

ideo PCB Assembly Parts List

Designator Description Part No.

Integrated Circuits 1A Type-74LS157 Integrated Circuit 1B 1 4LS157 Integrated Circuit Ic - 418157 7 Integrated Circuit ID

IE IF 1H 4 Integrated Circuit Vy 4 Integrated Circuit

1K Type-74L832 Integrated Circuit IL 45 Integrated Circuit IM 5 Integrated Circuit IN Type-74L8244 Integrated Circuit

IP ‘Type-74L8244 Integrated Circuit iR Type-74L8244 Integrated Circuit Is ype-741,8244 Integrated Circuit IT Type-74574 Integrated Circuit

3P/R ARIS Ty pe-61 16P-3, 150 ns RAM Integrated Circuit 150 ns RAM Integrated Circuit 150 ns RAM Integrated Circuit 150 ns RAM Integrated Circuit Type Type-61 16F

39 Integrated Circuit 4 Integrated Circuit ) 374 Integrated Circuit ‘Type-74LS32 Integrated Circuit

4 Integrated Circuit 74874 Integrated Circuit 415139 Integrated Circuit 418374 Integrated Circuit

374 Integrated Circuit 74832 Integrated Circuit

Type: 6116P- Type-6116

-74L8153 Integrated Circuit Type-74L5153 Integrated Circuit Type-74L8154 Integrated Circuit Type-74LS153 Integrated Circuit

Type-74$ 174 Integrated Circuit Type-7418153 Integrated Circuit Type-74LS153 Integrated Circuit 6116P-3. 150 ns RAM Integrated Circuit

Type-6116P-. 150 ns RAM Integrated Circuit Type-6116P-4. 150 ns RAM Integrated Circuit 137211-001 137211-001 137211-001

137211-001 137211-001

Page 68

Itustrated Parts Lists

Video PCB Assembly Parts List, Continued Championship Sprint

DesignatorDescriptionPart No.
3TType-6116P-3, 150 ns RAM Integrated Circuit137211-001
4AType-74F374 Integrated Circuit (Acceptable substitute is T137420-001

Integrated Circuit, part no, 137422-001)

4BType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

4CType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001) 4D Type-74LS163A Integrated Circuit 4E Type-74LS163A Integrated Circuit

4E/E Type-745157 Integrated Circuit 4E Type-74LS273 Integrated Circuit 4H Type-74L$273 Integrated Circuit 3

4Type-74LS163A Integrated Circuit37-74LS163A,
4KType-74874 Integrated Circuit37-74874
4LType-74LS273 Integrated Circuit37-74LS273
4MType-74LS273 Integrated Circuit37-74L$273
4N‘Type-74F374 Integrated Circuit (Acceptable substitute is Type-74A8374N137420-001

Integrated Circuit, part no. 137422-001)

4PType-74S174 Integrated Circuit137209-001
ARType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no, 137422-001)

48Type-74LS273 Integrated Circuit37-74LS273,
4TType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

5AType-74504 Integrated Circuit37-74804
5BType-74LS109 Integrated Circuit37-74LS109
SBICType-74LS08 Integrated Circuit37-74LS08
5ciDType-74808 Integrated Circuit37-74808
SDType-74LS163A Integrated Circuit37-74LS1634
SEType-74LS163A Integrated Circuit7-74LS163A
SFType-74LS174 Integrated Circuit37-74LS174
5HType-74LS174 Integrated Circuit37-74LS174
5)Type-74F163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-061)

5KType-74LS04 Integrated Circuit37-74LS04
SLType-74LS283 Integrated Circuit137204-001
5MType-74LS283 Integrated Circuit137204-001
SNType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

SPType-82$131 Program PROM Integrated Circuit136034-131
5RType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

58Type-74LS273 Integrated Circuit37-74L8273
STType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N Inte-137420-001

grated Circuit, part no. 137422-001)

OA200 ns Type-27256 EPROM Integrated Circuit136045-x105
6B200 ns Type-27256 EPROM Integrated Circuit136045-x106
6c200 ns Type-27256 EPROM Integrated Circuit136045-x107

“x” in the part number denotes the revision level

5-30

Page 69

Championship Sprint Illustrated Parts Lists

Video PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
ODIE200 ns Type-27256 EPROM Integrated Circuit136045-x108
OEIFype-74LS163A Integrated Circuit37-74LS163A

OE/E Type-74L$32 Integrated Circuit GOFIH 200 ns Type-27256 EPROM Integrated Circuit

OHS200 ns Type-27256 EPROM Integrated Circuit136045-x110
6K200 ns Type-27256 EPROM Integrated Circuit136045-x111
6L200 ns Type-27256 EPROM Integrated Circuit136045-x1 12
OM200 ns Type-27256 EPROM Integrated Circuit136045-x113
ON200 ns Type-27256 EPROM Integrated Circuit136045-x114
6P/R200 ns Type-27256 EPROM Integrated Circuit136045-x115
ORS200 ns Type-27256 EPROM Integrated Circuit136045-x116,
oT200 ns Type-27128 EPROM Integrated Circuit136045-x117
TA200 ns Type-27512 EPROM Integrated Circuit (Acceptable substitute is a 250 ns136045-x101

EPROM)

7B200 ns Type-27256 EPROM Integrated Circuit136045-x102
7C200 ns ‘Type-27256 EPROM Integrated Circuit136045-x 103
TDIE200 ns Type-27512 EPROM Integrated Circuit (Acceptable substitute isa 250.ns—-136045-x104

EPROM)

TEIFType-74LS00 Integrated Circuit37-74LS00,
7F/HType-74S08 Integrated Circuit37-74808
THIType-74LS158 Integrated Circuit137203-001
valType-74LS158 Integrated Circuit137203-001
7K$194 Integrated Circuit137424-001
TLy$194 Integrated Circuit137424-001
7MType-74LS158 Integrated Circuit137203-001
7Type-74L$158 Integrated Circuit137203-001
7PType-745194 Integrated Circuit137424-001
TRType-745194 Integrated Circuit137424-001
7sType-745 194 Integrated Circuit124-001
77Type-74$194 Integrated Circuit137424-001
8AType-74S194 Integrated Circuit137424-001
8B$194 Integrated Circuit137424-001
8BIC94 Integrated Circuit137424-001
8C/DTypeS194 Integrated Circuit137424-001
8DType-74F163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

8EType-74LS163A Integrated Circuit37-74LS163A
8FType-74L$74 Integrated Circuit37-74LS74
8HType-745162 Integrated Circuit137342-001
3]Type-748194 Integrated Circuit137424-001
8LType-74LS20 Integrated Circuit37-74LS20
8MType-745244 Integrated Circuit1-001
8NType-2149,35 ns Static RAM Integiated Circuit137199-003
8PType-2149, 35 ns Static RAM Integrated Circuit137199-003,
8RType-74F168 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

8SType-74F 163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no, 137421-001)

in the part number denotes the revision level

5-31

Page 70

Ulustrated Parts Lists

Video PCB Assembly Parts List, Continued Championship Sprint

DesignatorDescriptionPart No.
8TType-74163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Circuit, part no. 137421-001)

OA189 Integrated Circuit37-748 189
OBType-74S158 Integrated Circuit137312-001

OBIC Type-748189 Integrated Circuit 9CciD Type-745189 Integrated Circuit 9D Type-74S189 Integrated Circuit

9E 189 Integrated Circuit OF 4 Integrated Circuit oH Type- 74$153 Integrated Circuit oy Type-74L8244 Integrated Circuit

oKType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-901)

OLType-74F374 Integrated Circuit (Acceptable substitute is Type-7448374N137420-001

Integrated Circuit, part no. 137422-001)

9M244 Integrated Circuit137333-001
ONTy pe-2149, 35 ns Static RAM Integrated Circuit137199-003
OP.Type-2149, 35 ns Static RAM Integrated Circuit137199-003
ORType-74F 163 Integrated Circuit (Acceptable substitute is Type-74A5 163N13 7345-001

Integrated Circuit, part no, 137421-001)

9sType-74F 163 Integrated Circuit (Acceptable substitute isType-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

oréF163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

10AType-74$158 Integrated Circuit137312-001
10BType-74F374Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

10B/CType-74S00 Integrated Circuit37-74S00
10C/D,Type-745283 Integrated Circuit137241-001
10D153 Integrated Circuit1
10E74S153 Integrated Circuit1

10F Integrated Circuit 3

10HType-74L8244 Integrated Circuit3
10)‘Type-74F374 Integrated Circuit (Acceptable substitute isType-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

10KType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

10LType-74F374 Integrated Circuit (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

10M‘Type-74S244 Integrated Circuit137333-001
10NType-2149, 35 ns Static RAM Integrated Circuit137199-003
10PType-2 149, 35 ns Static RAM Integrated Circuit137199-003
10R‘Type-74F163 Integrated Circuit (Acceptable substitute is Type-74A$163N137345-001

Integrated Circuit, part no. 137421-001)

10S‘Type-74F 163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

10TType-74F163 Integrated Circuit (Acceptable substitute is Type-74AS163N137345-001

Integrated Circuit, part no. 137421-001)

MAType-745189 Integrated Circuit37-748189
Page 71

Championship Sprint Mlustrated Parts Lists

Video PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.

1B $158 Integrated Circuit 137312001 BIC S112 Integrated Circuit 137334-001

1iciDType-74800 Integrated Circuit0
IDType-74808 Integrated CircuitS08
LEi748153 Integrated Circuit3-001
IFIsStatic RAM Integrated Circuit1S7T199-002
11H5 ns Static RAM Integrated Circuit137199-002
Wy5 ns Static RAM Integrated Circuit137199-002
11K5 ns Static RAM Integrated Circuit137199-002

IL 37-74832

11M Integrated Circuit Type:

INIntegrated Cy

11P Integrated Circuit Type-74886 MIR Integrated Circuit Type-74L832

11s 74LS08 iT 32 124 ieee Circuit Tipe

12BIntegrated Circuit Type-i 372, 56-001
12BICIntegrated Circuit Type-7480437-74804

leciD Integrated Circuit Type- 12D 137423-001 12E 137209-001

12FIntegrated CircuitType-74L8174
12HIntegrated Circuit Type-74F374 (Acceptable substitute is Type-74A8374N137420-001

Integrated Circuit, part no, 137422-001)

12)Integrated Circuit Type-74F 374 (Acceptable substitute is Type-74AS374N137420-001

Integrated cuit, part no. 137422-001)

12Kcuit Type-74P374 (Acceptable substitute is Type-74AS374N137420-001

Integrated Circuit, part no. 137422-001)

Integrated Circuit Type-7406 37-7406 Integrated Circuit Type-74LS74 LS74 Integrated Circuit Type-745 112 137334001 Integrated Circuit Type-74L$32

13C/DIntegrated Circuit Type-74LS260137332. 2-001
13DIntegrated Circuit Type-740737
BEIntegrated Circuit Type-748174137209-001
13FIntegrated Circuit Type-74L50837-74LS808
13HIntegrated Circuit Type-74F374 (acceptable substitute isType-74AS374N137420-001

Integrated Circuit, part no. 12

13]Integrated Circuit Type-74Ls137332 “001
13KIntegrated Circuit Type-74064

13L Integrated Circuit Type-7406

Sockets 24-Contact, Medium-Insertion-Force IC Socket 28-Contact. Medium-Insertion-Force IC Socket 79-42C28

yw we O

Page 72

Mustrated Parts Lists

Video PCB Assembly Parts List, Continued Championship Sprint

Designator Description Part No.

C10 C11-C13 cl4 cls

C16 C17 c18 C19-C138,

C139-Cl41 C142 Cl4: C147

Ji3 JI9

R4 R17, RIB

RI9 R20 R21, R22 R23

R24 R25 R26 R27 Capacitors Capacitor, Aluminum, 100 pF, 35 V Capacitor, Aluminum, 100 pF, 35 V Capacitor, Ceramic, .1 ¢E 50 V Capacitor, Ceramic, .1 pE 50 V

Capacitor, Aluminum, 100 gk, 35 V Capacitor, Electrolytic, 1 ¢F, 50 V Capacitor, Ceramic, .1 aE, 50 V Capacitor, Mica, 47 pF, 100 V

Capacitor, Mica, 68 pF, 100 V Capacitor, Ceramic, .1 4F, 50 V Capacitor, Ceramic, 100 pF, 100 V Capacitor, Ceramic, .1 pF, 50 V

Capacitor, Ceramic, 100 pF, 100 V Capacitor, Ceramic, .1 pF, 50 V Capacitor, Ceramic, 100 pF, 100 V Capacitor, Ceramic, .1 pF 50 V

Capacitor, Ceramic, .001 pF 50 V Capacitor, Ceramic, .1 pF, 50 V Capacitor, Ceramic, .1 pF, 50 V

Connectors Connector, Header, 1 1-Circuit, .156 ctr, pol Connector, Header, Sq. Pin, 1 1-Circuit, .100 ctr

Ferrite Beads and Inductors Inductor, | #H Ferrite Bead Ferrite Bead Ferrite Bead Inductor, 100 pH

Transistors Type-2N3904 Transistor Type-2N3906 Transistor Type-2N3904 Transistor Type-2N3906 Transistor

Type-2N3904 Transistor Type-2N3906 Transistor Type-2N3904 Transistor Type-2N3906 Transistor Type-2N3904 Transistor

Resistors 150.0, +5%, 4 W Resistor 10KQ, +5%, % W Resistor 68.0, +5%, % W Resistor 2209, +5%, % W Resistor

I1KQ, +5%, 4 W Resistor 1209, +5%, 4 W Resistor 1802, +5%, 4 W Resistor 2209, +5%, 4 W Resistor

4702, +5%, & W Resistor 1KQ, +5%, % W Resistor 20, +5%, % W Resistor 1502, +5%, % W Resistor 122002-104

24350107, 24-500105 122002-104 12800. 0

128002-680 122002-104 122016-101 122002-104

122016-101 122002-104 122016-101 122002-104

122002-102 122002-104 122002-104

179014-011 179118-011

141007-001 141003-005 141003-005, 141003-005 141019-001

34-2N3904 33-2N3906 34-2N3904 33-2N3906

34-2N3904 33-2N3906 34-2N3904 33-2N3906 34-2N3904

110000-151 110000-103 110000-680 110000-221

110000-102 110000-121 110000-181 110000-221

110000-471 110000-102 110000-202 110000-151

Page 73

Championship Sprint Ilustrated Parts Lists

Video PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
R2839K Q, + 5%, 4 W Resistor110000-392
R2925%, 4 W Resistor110000-391
R30680, +5%, 4 W Resistor110000-680
R314702, +5%, % W Resistor110000-471
R32682, £5%, % W Resistor110000-680
R33100, 45%, %4 W Resistor110000-100
R346202, + 5%, % W Resistor110000-621
R351.2KQ. 45%, 4 W Resistor110000-122
R362.4K Q, 25%, 4 W Resistor110000-242
R375.1KQ,5%, 4 WResistor110000-512
R388202, +5%, 4 W Resistor110000-821
R3910KQ, +5%, % W Resistor110000-103
R40, Ral160.0, 45%, 4 W Resistor410000-161
R42390.0,+5%, % W Resistor110000-391
RB680, +5%, 4 W Resistor110000-680
R444709, + 5%, % W Resistor110000-471
RAS68.0, +5%, % W Resistor110000-680
RAG10.0, +5%, 4 W Resistor110000-100
RA?6200, £5%, % W Resistor110000-621
R481.2K Q, +5%, % W Resistor110090-122
R4924K 9, + 5%, % W Resistor110000-242
R505.1K Q, +5%, 4 W Resistor110000-512
R518200, +5%, %4 W Resistor110000-821
R5210K, +5%, % W Resistor110000-103
R531602, +£5%, 4 W Resistor110000-161
R54390.0, £5%, & W Resistor110000-391
R55682, +5%, % W Resistor110000-680
R564700, +5%, %& W Resistor110000-471
RST682, +5%, 4 W Resistor110000-680
R58109, +5%, %& W Resistor110000-100
R596200, 45%, Ye W Resistor110000-621
ROOL.2KQ, £5%, % W Resistor110000-122
ROI24K Q, +5%, Ys W Resistor110000-242
ROZ5.1K Q,5%, %& W Resistor110000-512
RO38209, +5%, %& W Resistor110000-821
R6410K Q, +5%, 4 W Resistor110000-103
ROS-R76,IK Q, +5%, %& W Resistor110000-102
RIT0G, £5%, % W, Resistor110005-001
R782202, +5%, % W Resistor110000-221
R792700, +5%, % W Resistor1000-271
R802700, +5%, & W Resistor110000-271
RN1, RN2680 @x 7 SIP Resistor Network118007-681
HSYNC, VSYNCOQ, £5%, % W, Resistor110005-001

Miscellaneous

cRIDiode, Light Emitting, MV505338-MV5053
YICrystal, 32 MHz144003-002

Terminal, Fast-On Tab (Acceptable subsitute is Test Point, part no. 020670-001) 179051-002

Page 74

Championship Sprint Ulustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

1g oF any part thereof, Except for may

'3@, No right is granted to reproduce

Figure 5-11 Audio Il PCB Assembly A043661-01 B

5-36

Page 75

Championship Sprint Illustrated Parts Lists

Audio II PCB Assembly Parts List

Designator Description

Capacitors C1-c5 3300 gE, 25 V Radial Electrolytic Capacitor C6-C12 1 wk. 50 V Ceramic Capacitor C13-C14 22 wE 35 V Electrol! C15-C18

001 pF 50 V 122002-102 1 pF S0.V 122002-104

Diodes

CRI-CR4Type-1N5401 Diode31-1N540]
CRS5-CRIOType-1N4001 Diode31-1N4001
CRISType-1N4002 Diode31-IN4002

Connectors Key 2.9 Ckt., .156-Inch Cur. Header Connector 179213-009 Key t.. .156-Inch Ctr. Header Connector 179213-009

2Ckt., .156-Inch Ctr, Header Connector179213-002
Key3, 6 Ckt., .156-Inch Ctr. Header Connector1792.13-006

Integrated Circuits

Q1-Q2Type-TDA-2030 Amplifier137301-001
@up Type-7815 Integrated Circuit37-7815

Resistors

RL10 kQ, Dual Horizontal Pot Resistor119011-103
R310Q, +5%, % WResistor110000-100
R4-R722 kQ,v4 W Resistor110000-223
R8-R910 kQ,4 W Resistor110000-103
R1O-RII1kQ, 45%, 4 W Resistor110000-102
RI2Z-R131Q,5%, 4 W Resistor110000-010
R14OQ, +5%, & W Resistor110005-001

Miscellaneous

SWSPDT Miniature Slide Self-Test Switch69-004
TP28-TP29#6-32 x 3/8-Inch Cross-Recessed Pan-Head Screw72-16068)
TP2#6-32 Nut/Washer Assembly75-99516
TP2Thermal Compound78-16001
TP28-TP29/pe-TDA-230 Heat Sink178190-032
TPIOL(0.x 3/8-Inch Cross-Recessed Pan-Head Screw2-14068
TPIOL#4-40 Nut/Washer A:5-99514
TPLOLThermal Compound78-16001
TPIOL‘Type-7815 Heat Sink178190-124

Hot Melt Adhesive 106006-001 Test Point 179051-001

a ow

Page 76

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 77

Chapter 6

Kit Installation

Your Championship Sprint game uses the System Ii” cabinet designed to accept the necessary hardware to easily convert the cabinet into a variety of games. This chapter contains information that applies to those parts of your existing System Il cabinet that are added or replaced to convert the cabinet to a Championship Sprint game. (See Figure 6-1.) The conversion instructions include: (1) replacing the attraction film, control panel, and some integrated circuits (ICs) on the game printed-circuit board (PCB); (2) installing the foot pedal assembiy and the cabinet control harness assembly, and (3) cleaning the video

display. See Figure 6-1 for the locations of the parts of the

System II cabinet that are replaced, installed, andcleaned. Wiring and schematic diagrams for the Championship Sprint game are contained in the Schematic Package Supplement (SP-292) included with your game. System II Paperboy” games located in the field were built with a different power supply, Audio PCB, and utility panel than the System II Championship Sprint games. Refer to Chapter 5, Illustrated Parts List, in the Paperboy Operators Manual (TM-275) for information regarding these components. The figure number in the manual and the part number for cach of these components follow:

Figure No.Part No.Component
55A037671-16Linear Power Supply

5-6 4043146-01 — Utility Panel 5-12 A043046-01 — Regulator/Audio II] PCB

Refer to CO-275-A043785-xxSierracin 5-Volt Power

01 Supplement Supply

For the wiring and schematic diagrams, refer to the Paperboy Schematic Package Supplement (SP-275) and the Sierracin 5-Volt Power Supply Supplement (CO-275-01),

NOTE If you do not have the Paperboy manual or the supplements, use the form in the back of this

manual to obtain a free copy:

Page 78

Kit Installation Championship Sprint

. Product Identification Label

CPU PCB Components Kit

Cabinet Control Harness

Ge PCB Components Kit

Ce

Dual Foot Pedal Assy

Figure 6-1 Kit Part Locations

Page 79

Championship Sprint

Kit Parts Inventory The assemblies listed in Table 6-1 are included in the Championship Sprint Conversion Kit. Refer to Chapter 5, Illustrated Parts List, for a description of the component parts comprising the control panel, foot pedals, CPU PCB assembly, and Video PCB assembly listed in Table 6-1

Tools Required The only tools required to perform a complete Championship Sprint conversion are a Phillips screwdriver, 1/8-inch hex driver, 7/16-inch nut driver, 9/1¢-inch openend wrench, chip extractor tool, flat black paint, and Scotch tape (or stapler). (A 3/8-inch wrench is also required if your game has a vertically mounted video display.)

Conversion Instructions

Table 6-1 Championship Sprint Kit Parts Inventory A043726-xx

Quantity Part No. Description

A043692-021Control Panel Assembly
A043708-011Cabinet Control Harness

Assembly

A043734-011Video PCB Components Kit
A043735-011CPU PCB Components Kit
A043745-011Foot Pedal Assembly

-406 LD. x 1.25 0.D. Wide-Pattern Flat Washer 175005-004 1

#1/4-20 x 1 ¥-Inch Black Square-Neck Round-Head Car- 75-5524B 2

riage Bolt

75-70022#1/4 Special Fender Flat Washer
75-995152#1/4-20 Nut/Washer Assembly
75-99519243/8-16 Nut/Washer Assembly
038158-011Product Identification Label

(Non-UL)

043729-011Attraction Film With Graphics
SP-2921Schematic Package Supplement
ST-2921Self-Test Label
TM-2921Operators Manual

Kit Installation

A WARNING A To avoid electrical shock, unplug the game before performing the conversion procedures.

The following procedures are arranged in the sequence recommended for performing the game conversion. The parts of your cabinet that are affected by the conversion are removed first and then replaced by the new Championship Sprint kit parts.

NOTE The following conversion should be performed by qualified service personnel.

Replace the Attraction Film Perform the following procedure to remove/replace the existing attraction film with the Championship Sprint attraction film. (See Figure 6-2)

  • Turn off the game power.
  • Using a 1/8-inch hex driver, remove the three screws and washers holding the upper retainer to the top of the cabinet
  • Grasp the top edge of the existing attraction film behind the attraction shield and slide it up to remove.

1/8-inch Hex-Head Screws Upper Attraction (3 places) Retainer Shield

Attraction

Figure 6-2 Attraction Film Replacement

6-3

Page 80

Kit Installation

4, Install the Championship Sprint attraction film. Make sure the film is fully inserted into the bottom slot.

  • Remount the upper retainer.

Replace the Control Panel

Perform the following procedure to remove/replace the existing control panel with the Championship Sprint control panel. (See Figure 6-3).

  • Using a 1/8-inch hex driver, loosen the two screws holding the lower retainer to the cabinet.
  • Unlock and open the coin door on the front of the cabinet.

. Carefully reach up through the coin door opening and release the spring draw latches located under the control panel on both sides of the cabinet. wy

  • Using a 1/8-inch hex driver, remove the two screws and washers holding the front of the control panel to the cabinet,
  • Gently lift the front of the control panel until the front edge clears the cabinet.
  • Carefully slide the top edge of the control panel from under the lower retainer.
  • Lift the control panel from the cabinet just far enough to expose the control-panel harness connector.
  • Disconnect the player control harness connector and remove the control panel from the cabinet.

Lower Retainer

1/8-inch Hex Head Screw (2 places)

Button-Head Screw (2 places) Harness Connector Championship Sprint

9, Install the Championship Sprint control panel in the reverse order of removal

Install the Cabinet Control Harness Perform the following procedure to install the cabinet control harness. (See Figure 6-1.)

  • Remove the existing control harness.
  • Plug the cabinet control harness connectors P102, P106, and P103 into the CPU PCB at J102, J106, and J103, matching keyed connectors with keyed PCB headers.
  • Route the harness along the existing cabinet harness and attach both together with two twist cable ties. 4, Plug the 12-position harness connector P24 into the control panel harness connector. wa Plug the 6-position harness connector P25 into the foot pedal harness connector after the foot pedals have been installed.
  • Connect the two green ground wires to the corner mounting screw located at the edge of the switching/ linear power supply chassis.
  • Mount the harness to the cabinet right side panel with screws at the screw-down tie-wrap locations.

Clean the Video Display Glass

Static electricity attracts dust to the video display glass and can cause the video image to grey out, making the

Spring Draw Latches

Control Panel

(2 places)

Coin Door w

Figure 6-3 Control Panel Replacement

6-4

Page 81

Championship Sprint

screen colors appear faded. In order to prevent this from happening, the video display glass must be cleaned. Perform the following procedure to clean the display glass.

  • Using a 1/8-inch hex driver, remove the two screws holding the lower retainer to the cabinet.
  • Grasp the display shield on the bottom edge and gently pull itout about one half inch from the cabinet.
  • Gently lower the display shield to free the top edge from under the speaker grille 4, Using a glass cleaner, clean the display glass and the monitor screen. Be sure to avoid spraying the bezel. wn Replace the display shield in the reverse order of removal

Install the Foot Pedals

Dual foot pedals are used in the Championship Sprint game. Perform the following procedure to install the foot pedals.

  • Using a Phillips screwdriver. remove the four screws holding the pedestal front panel to the cabinct. Remove the front panel.
  • Using a Phillips screwdriver, remove the two vs from both mounting cleats inside the pedestal side panels. Remoye the cleats.
  • Paint any unfinished surfaces within the pedestal cnclosure with flat black paint.
  • After the paint has dried, insert the foot pedals into the pedestal enclosure opening. Be sure the foot pedal harness is inserted first into the rear enclosure wall opening. Then fasten the foot pedals to the rear enclosure wall with two carriage bolts. Be sure that the bottom of the adjustable glide protrudes through the hole at the front of the pedal frame.
  • Using a 9/16-inch open-end wrench, tighten the nut and washer of the glide. (The nut and washer are supplied in the kit.) From the rear of the cabinet, using a 7/16-inch nut driver, tighten the two nuts and washers of the bolts.
  • Connect the foot pedal harness to the cabinet control harness inside the rear of the cabinet.
  • Using the existing Phillips screws, mount the pedestal front panel and two cleats on the inner rear cabinet wall opposite the rear access panel for future use.

IC Kit Anew set of 28 integrated circuits (ICs) has been designed for your Championship Sprint Game PCBs. Table 6-2 lists the ICs and their locations on the CPU and the Video PCBs. Kit Installation

Location of Replacement ICs

The CPU PCB Assembly and the Video PCB Assembly showing the location of each IC to be added, deleted, or replaced are included in this manual. (See Figures 6-4 and 6-5.) Each IC location is marked with the letter A, D, orR.

A represents an EPROM to be added D represents an EPROM to be deleted R represents an EPROM to be replaced

Install the Game ICs

Perform the following procedure to install the new integrated circuits (ICs).

A WARNING A

To avoid electrical shock, unplug the game before performing the conversion procedures if you have not already done so.

  • Unlock and open the rear access panel.
  • Remove the four thumb nuts holding the EMI cover to the ground plane. (See Figure 3-4.)
  • Refer to the CPU PCB Assembly and Video PCB Assembly, and determine the location of the ICs to be replaced, added, and removed. (See Figures 6-4 and 65.)
NOTE Slide a block of wood or similar device behind the PCBs to prevent the PCBs from bending excessively when installing the ICs.

4, Locate each IC to be replaced or removed, and remove each with a chip extractor tool, . For each replacement IC, align all of the pins on one side of the chip, and bend that row inward so that it is parailel to the other row. Carefully insert the chip into the proper socket on the game PCB, making sure the orientation notch faces the correct direction. (The notch differs on the CPU PCB and the Video PCB.)

  • Then locate each new IC to be added, and insert each in its correct socket. ve
  • Install the CPU PCB label (Atari part no. 043754-01) and the Video PCB label (Atari part no, 043753-01) on the respective PCBs.
  • Reinstall the EMI cover, and connect all the harness connectors.
Page 82

Kit Installation Championship Sprint

Table 6-2 Integrated Circuits in Championship Sprint Conversion Kit

DesignatorDescriptionPart No.

ICs on Championship Sprint CPU PCB:

Basic Set of ICs:

2B/C300 ns Type-27128 EPROM Integrated Circuit136045-xI18
2D300 ns Type-27128 EPROM Integrated Circuit136045-x119
4MSLAPSTIC Custom Integrated Circuit137412-109
6K300 ns Type-27256 EPROM Integrated Circuit136045-x124
6L300 ns Type-27256 EPROM Integrated Circuit136045-x123,
OR300 ns Type-27256 EPROM Integrated Circuit136045-x121
6s300 ns Type-27256 EPROM Integrated Circuit136045-x120

U.S. Set of ICs:

OF300 ns Type-27256 EPROM Integrated Circuit136045-x125
ON300 ns Type-27256 EPROM Integrated Circuit136045-x122
TL300 ns Type-27128 EPROM Integrated Circuit136045-x126
IN300 ns Type-27128 EPROM Integrated Circuit136045-x127

German Set of ICs:

OF300 ns Type-27256 EPROM Integrated Circuit136045-x225
ON300 ns Type-27256 EPROM Integrated Circuit136045-x222
TL300 ns Type-27128 EPROM Integrated Circuit136045-x226
7N300 ns Type-27128 EPROM Integrated Circuit136045-x227

ICs on Championship Sprint Video PCB:

6A200 ns Type-27256 EPROM Integrated Circuit136045-x105
OB200 ns Type-27256 EPROM Integrated Circuit136045-x106
6C200 ns Type-27256 EPROM Integrated Circuit136045-x107
6DIE200 ns Type-27256 EPROM Integrated Circuit136045-x108
OF/H200 ns Type-27256 EPROM Integrated Circuit136045-x109
OH200 ns Type-27256 EPROM Integrated Circuit136045-x110
6K209 ns Type-27256 EPROM Integrated Circuit136045-x111
6L200 ns Type-27256 EPROM Integrated Circuit136045-x112
6M200 ns Type-27256 EPROM Integrated Circuit136045-x113
ON200 ns Type-27256 EPROM Integrated Circuit136045-x114
PIR200 ns Type-27256 EPROM Integrated Circuit136045-x115
RIS200 ns Type-27256 EPROM Integrated Circuit136045-x116
6T200 ns Type-27128 EPROM Integrated Circuit136045-x117
7A200 ns Type-27512 EPROM Integrated Circuit136045-x101*
7B200 ns Type-27256 EPROM Integrated Circuit136045-x102
7C200 ns Type-27256 EPROM Integrated Circuit136045-x103
TDIE200 ns Type-27512 EPROM Integrated Circuit136045-x104*

*A 250 2s speed EPROM can be substituted if necessary ‘x’ in the part number denotes the revision level

NOTE NOTE

Some of the IC sockets might be left empty since The coin and credit option settings and the game the System II game PCBs are designed to accom- option settings must be reset for the Championmodate different ICs for a variety of games. ship Sprint kit conversion.

Reset the Coin and Credit and Game The settings are reset with the two dual-in-line package (DIP) switches at locations 6/7A and 5/6A on the CPU Option Settings PCB. (See Figure 1-2.) Each set of DIP switches contains

Page 83

Championship Sprint Kit Installation

Figure 6-4 Installing ICs into CPU PCB Assembly

6-7

Page 84

Kit Ingtallaion

Figure 6-5 Installing ICs into Video PCB Assembly Championship Sprint

Page 85

Championship Sprint

cight switches. Perform the following procedure to resect the option settings.

  • Remove the thin film of plastic covering the option switch, if any remains. nN . Using a pen or sharp-pointed instrument, slide the appropriate small button to the left or off position. (The stecring wheel controls and the pushbuttons are not used to change this setting.) Refer to Tables 1-2 and 1-3 in this manual for the available options and default (recommended) settings.

Install the Self-Test Label Staple or tape the Championship Sprint Self-Test Labei to the inner rear cabinet wall opposite the rear access door.

Install the Product Identification Label Perform the following procedure to install the Championship Sprint product identification label. 1, Remove the protective backing from the Championship Sprint product identification label.

  • Place the Championship Sprint product identification label over the existing product identification label on the back of the cabinet,

Inspect the Game Before applying power, perform the following inspection procedure i. Carefully check that the Championship Sprint conversion kit parts have been properly installed. Check that all the ICs are inserted properly with the orientation notch facing the correct direction. (Inserting an IC backwards can destroy the IC.) Make sure that the control-panel harness connector is tightly connected to the cabinet control harness connector, and that the spring draw latches under the control panel are securely fastened.

  • Plug in the game power cord.
  • Perform the self-test procedure as given in Chapter 2 Be sure that all of the DIP switches on the CPU PCB Kit Installation

have been properly set. Refer to Tables 1-2 and 1-3 in this manual for the available options and the default (recommended) settings. 4, Be sure to recalibrate each foot pedal. Refer to Calibration Procedure in Chapter 2.

  • Be sure to reset the high score table and the accounting information. Refer to the procedure in Reset the High Score Table and the Accounting Information later in this chapter. ©. Close and lock the rear access panel

Reset the High Score Table and the Accounting Information

The high score table and the accounting information. or game statistics, must be reset after completing the conversion to ensure accurate game data. This information is displayed on the Accounting Information screen in the Self-Test Mode. (Refer to Accounting Information in Chapter 2.) Perform the following procedure to reset this information. 1, Enter the Self-Test Mode by turning on the self-test switch, and press the red start (right) button until the Accounting Information screen is displayed.

  • Rotate the left steering wheel to select RESET HIGH SCORE TABLE.
  • Press the blue car button to change the NO message to YES.
  • Press the red start button to reset the high score table. After a brief PLEASE WAIT message is displayed, the self-test automatically advances to the next screen. Ww
  • Press the red start button until the Reset Saved Info Screen is displayed again. Rotate the left steering wheel to sclect RESET ACCOUNTING INFO.
  • Press the blue cat button to change the NO message to YES.
  • Press the red start button to reset the accounting information. After a brief PLEASE WAIT message is displayed, the self-test automatically advances to the next screen,
Page 86

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 87

Form to Obtain Free Paperboy Manual,

Schematic Package Supplement, and/or

5V Sierracin Power Supply Supplement

System II” Paperboy games located in the field were built with a different power supply, Audio PCB, and utility panel than most of the System IT Championship Sprint” games. The Paperboy Operators Manual (TM-275) has part number information on these components. The wiring and schematic diagrams are printed in the Paperboy

Publication(s) you need: C Paperboy Schematic Package Supplement (SP-275) and the Sierracin 5-Volt Power Supply Supplement (CO-275-01). If you do not have this manual or the supplements, you can obtain one free copy of each one that you need. To receive your free copy(ics), please fill in the information required below and mail this postage-paid form to us.

C1 Paperboy Operators Manual, TM-275 hemati¢ Package Supplement, SP-275 U Sierracin 5V Power Supply Supplement, CO-275-01

Championship Sprint game kit serial no

Game purchased from State

Your phone no. ( )

Please print!

Firm

Your name

State Zip

Page 88

Tape This Edge

First Fold

No postage necessary if mailed in the United States i

i

I

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 173 MILPITAS, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari Games Corporation

Attn: Customer Service 737 Sycamore Drive P.O. Box 361110 Milpitas, California 95035 <

Second Fold

From: —

Page 89

Left Coins

Right Coins

Add-A-Coins

2 Player Heats

0:30 1:60, ___. 1:30 2:00

2:30 —— Number of coins depos- Total Gam

Championship Sprint’

Coin Information and Game Statistics

Date: _

NOTE

Advance screens in the Self-Test Mode by pressing the

red start (right) button

Accounting Information

ited in left coin mechanism

Number of coins depos- Total Game Time ited in right coin mechanism

Total number of coins: deposited in all coin Average Game mechanisms during add- Time coin mode only

Total number of heats/ ‘Total On Time re! races tun with | player only Total number of heats! Total Time races run with 2 players

Reset Saved Info Screen

NOTE Use this scrcen only to reset high score table and accounting information

How to reset: select item to be reset with left stcering wheel. Push blue car (left) button to toggle between Yes and No. Press red start button to reset selected tables,

Resct Accounting Info? No

Reset High Score Table? No

Game Times*

3:00, ——__—_____ 3:30 Bao 6:00 4:00

5:00) —_________ 7:30 Total number of coins deposited in all coin mechanisms

Accumulated time of all 1- or 2-player games. layed in hours, min- , and seconds

Total game time divided by total games in hours, minutes, seconds

Total time in hour: utes, and st the game wa min- ‘onds that s turned on

Total time in hours, minutes, and seconds that the game was played

8:00 & Up

“Note: It is possible for a limited number of players to play Championship Sprint for over eight minutes. Generally: this com occur during a 2-player game when one or twa players lose frequently and continue using ibe addaecoin feature. In locations where there are many highly skilled player vou should expect to see 3-7 % of lotai games played at over eight mirtites (after four weeks on location).

Page 90

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 91

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and
  • Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 92

crime PPPPPED 6 bb ddaae rn

ATARI

GAMES

Atari Games Corporation ® P.O. Box 361110 © Milpitas, CA 95035 ® (408) 434-3950 ® Telex 5101007850