CATHODE RAY TOMES

Fast Freddie TM-208 1st Printing

Fly-Boy (Kaneko, 1982) · Technical Manual · 48 pages · 32 sections · original scan

Page 1

TM-208 1st printing

Page 2

GAME SERIAL NUMBER LOCATION Your game’s serial number is printed on a label on the outside back of the game. r The same number is also printed on a label on the chassis of the video display, power supply, Regulator/Audio I| Printed Circuit Board (PCB), and the game PCB. Please mention this number when calling your distributor for service.

GAME IDENTIFICATION, SERIAL NUMBER LABEL

VIDEO DISPLAY

[ 2

REGULATOR/ AUDIO II PCB

POWER SUPPLY

Page 3

ULI IDM ED LY AWN

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Page 4

Fast Freddie™

© 1982 by Atari, inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be siored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Fast Freddie™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If intringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Intringers may also have to pay costs and attorneys' fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us, Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO, Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 6L

Page 5

Fast Freddie™

Notice Regarding Non-ATARI Parts

-—WARNING—A:

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the following:

  • Substitute non-ATARI parts in your coin-operated game, or
  • Modify or alter any Circuits in your ATARI game by using kits or parts not supplied by Atari.

Not only may the use of any non-ATARI parts void the warranty, but any such alteration may also adversely affect the safety of the game, and may cause injury to you and your piayers.

Page 6

Fast Freddie™

Table of Contents

Set-Up Procedures A. New Features... 2... ee 4-3 B. Game Inspection . 1-3 C. Game Installation. ....... 1-3

  • Installation Requirements 2. 43
  • Voltage Selection ..... 2 43 D. Switch Locations . 1-4
  • On/Off Switch ..... 1-4
  • Utility Panel Switches 1-4
  • Option Switches .... 1-4 E. Option Switch Settings . 1-5 F. Self-Test Procedure ... 16 G. GamePlay .......... 18
  • Demonstration Mode 18
  • Attract Mode .... 18
  • Ready-to-Play Mode . 1-9 4, Play Mode ........ 1-9
  • High-Score Mode .. -. 110
  • Hints forGame Play ..................05. .. 110

Troubleshooting A. Comments on Troubleshooting. ...........0. cee cece eee eee eee 22 B. Self-Test Procedure ......... 0... cece cece eee eee e eee 22

Maintenance, Repair and Parts Cabinet-Mounted Assemblies............ 0.0.0. c ese e eee eee 3-2 The Control Panel ......... 3-4 anmoom> Fluorescent Tube and Speaker . Video Display ........... Coin Door... 6... ee eee eee cece Printed-Circuit Boards . . Power Supply Assembly

Page 7

Fast Freddie™

List of Illustrations

Figure 1-1 Game Overview 1-2 Figure 1-2 Game Switch Locations . 14 Figure 1-3 Self-Test Procedure . 1-6 Figure 1-4 Ready-to-Play Screen. . 1-8

Figure 2-1 Self-Test Screen 1—Test Passes ...... 0.0... ccc e cece cece eee 2-2 Figure 2-2 Self-Test Screen 1—Test Fails w 23 Figure 2-3. Self-Test Screen2 2.1.0.0... cece cece cence teens 2-3

Maintenance, Repair and Parts: Figure 3-1 Cabinet-Mounted Assemblies Figure 3-2 The Control Panel ....... Figure 3-3 Control Pane! Assembly ... Figure 3-4 8-Position Joystick Assembly

Figure 3-5 Fluorescent Tube and Speaker .... 0.2.0.0... 00 e ee eee 3-8 Figure 3-6 VideoDisplay............... Figure 3-7 Vertically Mounted Coin Door... . Figure 3-8 Printed-Circuit Board (PCB) Removal ..............0.. cece eee 3-14

  • 3-16 3-18
  • 3-20 Figure 3-9 Fast Freddie PCB Assembly Figure 3-10 Regulator/Audio Il PCB Assembly Figure 3-11 Power Supply Assembly

List of Tables

Tabie 1-1 Option Switch Settings .......... 0... eee een eee ee 1-5 Table 1-2 Fast Freddie Game Play and Scoring ............0. 0. eee eee 1-9

Page 8

Fast Freddie™

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) = From California, Alaska, or Hawaii (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) eee From New Jersey 2 (201) 469.5993 = From anywhere else in this area @@ toll-free (800) 526-3849

EUROPE Parts and service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) {RELAND

BH 06252155

vi

Page 9

Set-Up Procedures

Y

<

How to Use This Manual

This manual, written for game operators and service technicians, describes the Fast Freddie™ game. Chapter 1 describes new features, game setup, option switch settings, self-test procedures, and game play. Chapter 2 contains troubleshooting procedures. Chapter 3 details maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

Chapter

Page 10

Set-Up Procedures Fast Freddie™

FLUORESCENT TUBE AND SPEAKER See Figure 35

COLOR VIDEO DISPLAY See Figure 3-6 ACCESS PANEL

& POSITION JOYSTICK See Figure 3-4

CONTROL PANEL See Figures 3-2 & 3-3

GAME PCB See Figures 38 & 39

COIN DOOR See Figure 3-7

iN

UTILITY PANEL See Figure 1-2 REGULATOR! AUDIO II PCB See Figures 3-8 & 3-10

POWER SUPPLY See Figure 3-11

WARNING SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded! POWER ON/OFF SWITCH See Figure 1-2

Figure 1-1 Game Overview

Page 11

Fast Freddie™

A. New Features

The Fast Freddie™ game has three new features. Even if you are familiar with ATARI® games, you should note these important differences:

  • Joystick Control. This new eight-position control is made of steel and molded plastic. It has few parts, which make servicing easier. The leaf switches snap in and out for easy replacement. The rubber bellows are designed for a quick return to center.
  • Game Cabinet. The Fast Freddie™ cabinet has several new features. The cabinet grille is both a speaker grille and display-shield retainer. in addition, the upper part of the display shield also serves as the attraction panel.
  • Key Loops. The utility panel has two key joops. This provides a convenient place to store keys for the rear access panel and lower coin door. New features and ali other major parts in the game are iliustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol:

B. Game Inspection

Please inspect your game carefully to ensure that it was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the rear access panei, Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Check that ali plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. b. Check that all plug-in integrated circuits on the PCB are firmly seated in their sockets. Set-Up Procedures

c. Remove the tie-wrap that hoids the coiled power cord on the inside cabinet wall. Check the power cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood siot at the bottom of the rear panel opening. A—warninc—A,

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

d. Note the game serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Fast Freddie game PCB, Regulator/Audio 11 PCB, Power supply, and video display. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you Call your distributor for service. e. Check major subassemblies, such as the power supply, control panel, and video display for secure mounting.

C. Game Installation

  • Installation Requirements

Power 150 W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 79 cm (25% x 31 in.) Game Height 174 cm (68% in.)

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply may have three different voltage selection plugs: 100 VAC (violet wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for your location’s line voltage (see Figure 3-11).

4-3

Page 12

Set-Up Procedures

D. Switch Locations

  • On/Off Switch

The on/off switch is located on the back of the cabinet, lower left side (see Figure 1-2).

  • Utility Panel Switches

The utility panel includes the volume control, self test, coin switch, and coin counter(s). The coin switch is used to credit the game, and it activates Fast Freddie™

the left coin counter. These switches are located inside the upper coin door (see Figure 1-2).

  • Option Switches

Option switches are tocated on the game PCB at location B5 (see Figure 1-2).

KEY LOOP

UTILITY PANEL

COIN COUNTER SELF-TEST

col VOLUME CONTROL iN SWITCHES (To increase, turn clockwise)

Figure 1-2

1-4 GAME PCB POWER ON/OFF ‘SWITCH

Game Switch Locations

Page 13

Fast Freddie™

E. Option Switch Settings

Table 1-1 details game option switch settings on the game PCB. Options are preset at the factory and shown by the < symbols. However, you may change the settings to suit your individual needs.

Table 1-1 Set-Up Procedures

To verify option switch settings, push reset button or power the game off and then on again. Set the self-test switch to on and verify the settings on the self-test screen. Then set the self-test switch to off.

Option Switch Settings

This table contains switch settings for options relating to game price, number of Fast Freddie lives, and bonus options. The switches are on the game PCB at location BS.

Settings of & Toggle Switch on Fast Freddie PCB (at BS)

134567

8 Option

Off Off Off Off

On Off Off Off

Off On Off Off

On On Off Off Off Off On Off

On Off On Off

OffOnOnOff
OnOnOnOf
OffOffOffOn
OnOffOffOn
OffOnOffOn
OnOnOffOn
OffOffOnOn
OnOffOnOn
OffOnOnOn
OnOnOnOn

Off On

Off Off On Off Off On On On Left Coin Mechanism 1 coin counter Right Coin Mechanism 2 coin counters

1 coin for 1 credit < 2 coins for 1 credit 1 coin for 3 credits 1 coin for 2 credits 1 coin for 1 credit 2 coins for 1 credit 2 coins for 1 credit 1 coin for 1 credit

1 coin for 3 credits 1 coin for 4 credits 1 coin for 5 credits 1 coin for 6 credits 1 coin for 1 credit 1coin for 1 credit 1 coin for 1 credit 1 coin for 1 credit

1 coin for 2 credits 1 coin for 4 credits 1 coin for 5 credits 1 coin for 10 credits 1 coin for 2 credits 1 coin for 2 credits 1 coin for 2 credits 1 coin for 2 credits

1 coin for 11 credits 1 coin for 12 credits 1 coin for 6 credits Free play 1 coin for 2 credits 1 coin for 2 credits 1 coin for 2 credits Free play

3 Fast Freddie lives < 5 Fast Freddie lives

‘No bonus Bonus life every 30,000 points Bonus life every 50,000 points < Bonus life every 100,000 points

Off Upright cabinet < On Cocktail cabinet

<4 Manufacturer's recommended settings

Page 14

Set-Up Procedures

F. Self-Test Procedure

This game will test itself and provide data to show that the game's circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. Fast Freddie™

Refer to Figure 1-2 for the location of the self-test switch and option switches. To perform the selftest, set the self-test switch to on. To end the selftest, set the self-test switch to off. The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. |f a part of the test described in Figure 1-3 fails, refer to Chapter 2.

Figure 1-3 Self-Test Procedure

Instruction Test Passes

  • Set the selttest switch to on (see Figure 1-2).
  • Observe the eight colored squares.
  • Activate control panel and coin switches.
  • Simultaneously press the start 1 and KICK switches.
  • To end the self-test. The screen shows the self-test display. The RAMs and ROMs are tested and if they are good, the screen displays RAM OK and ROM OK. If the screen is different from the self-test display, refer to Chapter 2, Self-Test Procedure.

Colors are blue, violet, green, yellow, light blue, white, red, and blue. If colors are not as described, refer to the raster-scan video display manual.

The 0 changes to 7 as the switch is activated. If the test fails, refer to Chapter 2, Self-Test Procedure.

Push the joystick diagonally up and to the left. For proper game operation, both the top and left switches must close at the same time, and the top and left Os should each become 1s. Push the joystick in the three other diagonal directions (up and right, down and left, down and right), repeating the above procedure. The corresponding pair of switches should close in the same manner. If the test fails, refer to Chapter 3, 8-Position Joystick Assembly.

A game sound is produced. To go to the next sound simultaneously press the start 1 and KICK switches. Test all 10 sounds in this manner. If test fails, refer to Chapter 2, Self-Test Procedure.

Game Sounds

SOUND 0 Beginning of round SOUND 1 Fast Freddie gliding SOUND 2 Fast Freddie kicking SOUND 3 Picking up a letter SOUND 4 Fast Freddie falling SOUND 5 Fast Freddie gliding SOUND 6 Airplane falling SOUND 7 Helicopter, bird falling SOUND & Genie failing SOUND 9 Landing on platform

Simultaneously press the start 1 and start 2 switches. A crosshatch pattern appears on the screen. Then set the self-test switch to off. The Attract Mode will now be displayed.

Page 15

Fast Freddie™ Set-Up Procedures

COLOR ADJUSTMENT CHART

BLUE

VIOLET

GREEN

YELLOW

OPTION

SWITCHES pIP SA SETTI LIGHT BLUE

WHITE LEFT COIN 00000100 MECHANISM RED

BLUE/VIOLET 1 CREDIT RIGHT COIN MECHANISM c i CREDIT

UPRIGHT~—_— TYPE OF CABINET

_SONUS AFTER §0000 BONUS PLAYER 2 ‘ RT 1. START 2 START PLAYER 1 ‘ START SIN L COIN R ~ RIGHT COIN MECHANISM NO. OF LIVES

LEFT COIN u MECHANISM 0 PLAYER.2 JOYSTICK

  • (COCKTAIL ONLY) JOYSTICK (UPRIGHT)

PLAYER-2 KICK (COCKTAIL ONLY) SOUNDS

COIN SWITCH

KICK (UPRIGHT)

Figure 1-3 Self-Test Procedure, continued Self-Test Display

1-7

Page 16

Set-Up Procedures

G. Game Play

The Fast Freddie™ game is a one- or two-player game with a color raster-scan video display. The game depicts a hang-glider, Fast Freddie, gliding in the sky. Fast Freddie glides over the land and must avoid obstacles on the land and in the sky. As he glides along, he may pick up letters to spell the word BONUS for bonus points. He must pick up the letters in the correct order (B first, O second, etc). To end each round he must land on a landing platform. Fast Freddie has six possible modes of operation: demonstration, attract, ready-to-play, play, highscore and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time. (All credits will be cancelled and the high score table will be erased.)

1, Demonstration Mode Enter this mode by simultaneously pressing the coin switch and the self-test switch (see Figure 2). In this mode, you may see the more advanced rounds of game play. If Fast Freddie collides with any object in the sky, he does not crash. However, he must avoid obstacles on the ground and land on a platform to go to the next round. To end this mode, set the self-test switch to off.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode lasts for about 35 seconds, and ends only when a credit is entered, or when in selftest. In the attract mode, the screen displays one of three possible pictures. The first picture shows various ways a player may score points. At the top of the screen are the words 1UP, HIGH SCORE and 2UP (with corresponding scores). The words FAST FREDDIE flash on the screen and Fast Freddie is to the right of these words. The message KICK FLYING OBJECTS AND PICK UP FLAGS appears. Obstacles and their corresponding point value appear in the center of the screen. At the bottom of the screen is the message © ATARI, INC. 1982. Fast Freddie™

i vy ty gee

Figure 1-4 Attract Mode Screen

The second picture shows the high-score table. The words 1UP, HIGH SCORE and 2UP (with corresponding scores) appear at the top of the screen. The 10 highest scores and their corresponding initials appear in the center of the screen. The words © ATARI, INC. 1982 appear at the bottom of the screen. The third picture shows one of three versions of game play. Fast Freddie glides over an alpine setting and a plane hits him and he crashes to the ground. Or he glides over the ocean and a bird sends him crashing down. Or he glides over Egypt and a genie on a flying carpet hits him and he crashes to the ground. The words 7UP, HIGH SCORE and 2UP (with corresponding scores) appear at the top of the screen. The words SPELL BONUS and KICK anda rectangular gauge showing the amount of kick appear at the bottom of the screen.

Page 17

Fast Freddie™

  • Ready-To-Play Mode This mode begins when coins are inserted and accepted for game play. The words 1UP, HIGH SCORE and 2UP (with corresponding scores) appear at the top of the screen. The words PUSH START BUTTON and ONLY IPLAYER or 1PLAYER OR 2PLAYER and bonus life information appear in the center of the screen. The number of credits appears at the bottom right of the screen. If a game is set for two credits for one play and a player inserts only one coin, credits will not appear at the bottom of the screen until the second coin is inserted. This mode ends when a player presses a start button.
  • Play Mode \n the Play Mode, the player controls Fast Freddie with an eight-position joystick. Thus, the player Set-Up Procedures

causes Fast Freddie to glide in the sky and to avoid obstacles on the land and in the sky. The player may use KICK to destroy objects in the sky that are below him. Fast Freddie begins each life with about 12 seconds of KICK. A rectangular gauge at the bottom right of the screen shows the amount of kick remaining. Fast Freddie may pick up letters worth 100 points each to spell the word BONUS for bonus points. The letters he picks up are displayed on aline at the bottom of the screen. However, he must pick up the letters in the correct order to get the bonus points. If he spells the word BONUS, any remaining letters are worth 200 points each if picked up. Round one begins with Fast Freddie on a mountain in an alpine setting. He runs off the top of the mountain and glides in the sky. As he glides along, a

Table 1-2 Fast Freddie Game Play and Scoring

Round Terrain

1 Alpine (summer)

2 Sea (blue)

3 Egypt (green)

4 Alpine (autumn)

5 Sea (purple)

6 Egypt (red)

7 Alpine (winter)

8 Sea (brown)

9 Egypt (blue)

Obstacles Points

Airplanes 30 Helicopters 50

Airplanes 30 Birds 50

Disks 30 Genie on Carpet 50

Airplanes 50 Helicopters 70

Airplanes 50 Birds 70

Disks 50 Flying Carpet 70

Airplanes 70 Helicopters 90

Airplanes 70 Birds 90 Genie on Carpet 70 Flying Carpet 90

Gliding is worth 10 points per % inch (1.6 cm).

Picking up a letter on a flag is worth 100 points. If BONUS is spelled out, picking up a letter is worth 200 points.

Landing platforms are worth 1,000 to 5,000 points. if BONUS is spelled out, platforms are worth 5,000 to 25,000 points.

1-9

Page 18

Set-Up Procedures

flag with a letter on it appears below. He may pick up the letter and begin to spell out the word BONUS for extra points. As he picks up a letter it is displayed on a line at the bottom of the screen. He must pick up the letters in the order they appear in the word. If he picks up a letter out of sequence, the letters appearing on the line at the bottom of the screen will be erased. After a period of time, airplanes appear. They will destroy Fast Freddie if they hit him. The player uses his joystick to avoid the airplanes and KICK to destroy them. Fast Freddie must be above the airplanes (and other flying objects) to destroy them. A helicopter also appears, and Fast Freddie must avoid or destroy it also. Toward the end of the round, landing platforms appear on the ground. Fast Freddie must land on a platform to end the round. Each platform has a different point value. If the word BONUS is not spelled out, the platforms are worth 5,000 to 25,000 points. If the word BONUS is spelled out, the platiorms are worth 10,000 to 50,000 points. The words LANDING TIME:10 also appear. Fast Freddie has 10 seconds to land. If the landing is successful the next round will begin. Fast Freddie has nine rounds of game play. The first, fourth, and seventh rounds show an alpine setting in summer, autumn, and winter. The second, fifth, and eighth rounds depict an ocean setting with different colored backgrounds. The third, sixth, and ninth rounds take place in Egypt with different colored backgrounds. Each round has different obstacles. The game ends when all of Fast Freddie’s lives are used up.

1-10 Fast Freddie™

The screen displays several messages during game play. At the top of the screen are the words 1UP, HIGH SCORE and 2UP (with corresponding scores). At the bottom of the screen are the number of lives remaining, the bonus word or letter(s) collected, and gauge measuring the amount of kick remaining.

  • High-Score Mode This mode begins when a player has one of the ten top scores. The message REG/STER YOUR NAME appears on the screen. Below these words is a line containing the characters of the alphabet, RUB (erase), and END. A player enters his initials by moving the joystick to the left or the right to locate the correct letter. He causes the letter to be transferred to the right of the word NAME by pushing the KICK button. When he has entered three characters, they are automatically transferred into the highscore table.
  • Hints for Game Play
  • Stay in the center of the screen when possible.
  • It is not necessary to spell BONUS to get to the end of a round.
  • Avoid clouds in the ocean round.
  • Kick at any flying object that is below you and within range.
  • Try to land on the last landing platform for the most points.

> a

  • SS
Page 19

Troubleshooting

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or isn’t working properly. The expanded selftest procedures in this chapter are inciuded to help the qualified electronic technician determine why the game isn’t working properly.

Se Chapter

Page 20

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II PCB, or the video display? The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair are relatively simple, as these assemblies are not too complicated. If agame PCB is failing, troubleshooting and repair depend on your understanding of the operation of the PCB. To effectively troubleshoot a game PCB, it is necessary for you, the technician, to become familiar with the PCB hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.

oe

c} KOH —= ND iV, C} we, Nd 1 \ rs Fast Freddie™

B. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. The screen displays the picture below. See Chapter 1, Section F, Self-Test Procedure for a complete description of this picture.

NOTE This procedure does not test the coin door lockout coils and coin counter. If the Self-Test passes, but the lockout coils do not energize when power is applied to the game, suspect the lockout coil wiring or coin door harness. Troubleshoot using the game schematics.

Self-Test Screen 1 Figure 2-1 Test Passes

Page 21

Fast Freddie™

ERROR

ERROR

Figure 2-2 Self-Test Screen 1 Test Fails

SCREEN 1 RAM failure may be indicated by a blank screen or by garbage on the screen. It may also be indicated by or the word RAM and a number displayed at the top of the screen. The RAM and its location are listed as follows:

RAM chip location Screen Display on game PCB RAM 0 E11, E12 RAM 1 J10, J11 RAM 2 Di RAM 3 E16

ROM failure is indicated by the word ROM and a number displayed at the top of the screen. The bad ROM and its location are listed as follows:

ROM chip location Screen display on game PCB ROM 1 D16 ROM 2 DI7 ROM 3 C14 ROM 4 C16 ROM 5 Ci7 ROM 6 AM ROM 7 AIG ROM 8 Al7

SWITCH failure is indicated by the associated 0 not changing to a 7 on the screen when the switch is activated. Troubleshoot using the information in Chapter 3, Section B, and game schematics. SOUND failure is indicated by no sound. Check the volume control levels on the utility panel, or troubleshoot using the game schematics. To go to screen 2, simultaneously press start 1 and start 2 switches. Troubieshooting

Figure 2-3 Self-Test Screen 2

SCREEN 2

A white crosshatch pattern appears on the screen (see Figure 2-3). Use this pattern for convergence (see the raster-scan video display manual).

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Maintenance, Repair and Parts

AZ This chapter details maintenance and repair information, and provides information you need to order parts for your Fast Freddie game. Please note that common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed in the front of this manual for your convenience.

Chapter

Page 24

Maintenance, Repair and Parts Fast Freddie™

A. Cabinet-Mounted Assemblies

038226-01 Fluor. Tube & Speaker— Gries 178034024 See Figure 35 (FMolding) 03733201 (Grille)

038689-01 (Shield) 037721-02 Video Display— (Access Panel) see Figure 3-6 q \ . 74-2110 a ‘ i ‘ (Lock) 8 Position : : . Joystick Assy.— See Figure 3-4 78-6900402 (Tape) 178013-001 (Latch) /

Control Panel Assy.— see Figures 3-2 & 3-3

A038004-01 (Utility Sw. Harn.) Coin Door Assy.— see Figure 3-7

Rh Regulator/Audio II PCB Assy.— See Figures 38 & 3-10 - 038003-01 (Uti, Sw. Brkt) A002465-01 (Coin Counter) I Game PCB Assy.— ® [ YA See Figures 3-8 & 3-9

: A038718-01 A038453-01 : (Main Harn. Assy.) (Power Harn. Assy.)

69-001 (Self-Test Sw.) 62-041 «Coin Sw.) 19.9032 : (Vol. Control) A037491-01 4 178070-001 {Coin Box a (Knob) 78-3201 (Glide) A037454-03 (Power Cord)

Power Supply Assy.— 009992.01 See Figure 3-11 178048-001 (On/Off Sw. Cover) (Caster) A037470-01 (On/Off Sw)

Figure 3-1 Cabinet-Mounted Assemblies Ireland-Built Cabinet A038677-01 & -02 A

Page 25

Fast Freddie™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued Ireland-Built Cabinet Parts List

Part No. Description A002465-01 Coin Counter A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly A038453-01 Power Harness Assembly

A038678-01Cabinet Assembly(includes wood-grained side panels, glides, and PCB retainers, but not the

rear access panel) A038678-02 Cabinet Assembly (includes graphics on side panels, glides, and PCB retainers, but not the rear access panel) A0387 18-01 Main Hamess Assemoly The following four items are the technical information supplements to this game: ‘SP-208 Fast Freddie™ Schematic Package ST-208-01 Fast Freddie Label with SelfTest Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display Substitute TM-201 when using part no. 92-055, 19-Inch Wells Gardner Display. TM-208 Fast Freddie Operation, Maintenance and Service Manual

19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ¥4-Inch Wide x j;-Inch Thick 009992-01 On/Off Switch Cover

037721-02Rear Access Panel(does not include lock)
037332-01Ventilation Grille(located on cabinet top)

038003-01 Utility Switch Bracket for Volume Control, Self-Test Switch, Coin Switch, and Coin Counter 038226-01 Upper Cabinet Grille 038689-01 Video Display Shield with Graphics

038691-01Side Panel Decal(not shown in illustration)

178013-001 Spring Draw Latch 178034-024 ¥-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 178070-001 Volume Control Knob

J,

3-3

Page 26

Maintenance, Repair and Parts

B. The Control Panel

A—warninc—& Prior to removing or repairing any switch on the contro! panel, unplug the game.

To Open the Control Panel:

  • Open the coin door. Reach up through the opening and release the spring-draw latches. They are on the cabinet side walls at each end of the control panel. Fast Freddie™

Start-Switch Replacement:

that follow.

  • Lift up on the control panel at the top edge, and tilt it toward you. The control panel edge next to the display shield has foam tape applied to it. The tape cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.

Leaf Switch Repair: @ Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner. To Test Switch: These switches have a very low failure rate. If a switch should ever be suspect, first test it using the directions

@ Remove the wires from the suspected switch. @ Attach the leads of an ohmmeter to normally open and commen contacts. @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or aiways remain closed or open, then replace the switch.

@ To replace a leaf switch, remove the screw with a Phillips-head screwdriver. @ To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design. @ Reinstall the switch. Reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs on the switch. To Replace Switch:

trol panel. @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the con-

@ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.

Figure 3-2

3-4 START 2

The Control Panel ‘START-SWITCH CONTACTS START 1

BROWN WIRE NORMALLY OPEN CONTACT

BLACK WIRE COMMON CONTACT

YELLOW WIRE NORMALLY OPEN CONTACT

BLACK WIRE COMMON CONTACT

Page 27

Fast Freddie™ Maintenance, Repair and Parts

! WARNING ! Players may receive an electric shock if this control panei is not properly grounded! After (Control Panel/Decal) 471021-001 servicing any parts on the panel, check that the 038267-01 8-Position Joystick Assy.— ground wire is firmly attached to the metal tab (Control Panel) see Figure 3-4 ‘on the inside of the control panel. Only then 038692.04 should you lock up the game. (Decal) 78-6900402 = (Tape) 62.041 75-0108 — (Start Sw) (Flat Washer)

75-0408, (Split-Lock Washer)

759118 (Hex Nut) “reece

178030-003 75-9910NO (Pushbutton Assy.) (Nut) 75-5112B (Carriage Bolt)

AOBEARE AT 160013-001 (Harness) (Leat Sw./Button Holder) Figure 3-3 Control Panel Assembly lreland-Built Cabinet A038678-01 A Parts List

Part No. Description A038455-01 Control Panel Harness Assembly A038688-01 Control Panel with Decal 62-041 SPDT Momentary Pushbutton Start Switch 75-010S #10 Flat Washer 75-040S #10 Split-Lock Washer 7§-5112B #10-24 x 34-Inch Black Carriage Bolt 759118 #10-24 Hex Nut 75-9910NO #5,-11 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ¥-Inch Wide x }-Inch Thick (24 in. required) 038267-01 Control Panel 038692-04 Control Panel Decal 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (Leaf switch only is part no. 160012-001) 171021-001 8-Position Joystick Assembly 178030-003 Biack Pushbutton Assembly

Page 28

Maintenance, Repair and Parts

WARNING

Prior to removing or repairing the joystick, unplug the game.

To Repair the Joystick:

  • First remove the entire joystick assembly from the control panel (see Figure 3-3). Now locate the four screws in the plastic joystick frame and remove these screws.
  • Next remove the retaining ting from the bottom of the shaft. The assembly will come apart.
  • To replace the be//ows, pry it up and out of the plastic trame. @ Reassemble in reverse order. @ Note that the inner raised ring on the bellows is longer on one side. This side goes on the top of the assembly (toward the control knob).
  • To replace a /eaf switch, you don't need to disassemble the joystick. @ Using your thumbs, pry apart the plastic flanges on the switch holder. With your index finger, lift the switch up so that it will clear the plastic tab located on the outside end of the switch holder. @ Slide the switch out of its holder. Replace the switch in reverse order. Adjust the switch for a narrow gap.

99-080031 (Bellows)

99-080032 Disassemble in the indi- Had (eialed ae H (Steel Washer) cated. (Circled numbers match the numbered instructions.)

99-080030 (Seng) | 99-080037 (Sw. Plate)

@) s2ater6 (Screw) Fast Freddie™

~S

99-080028 (Shaft)

99-080026 (Black Plastic Washer)

99-980036 (Top Plate)

99-080029 (Nylon Washer)

99-080025 (Leaf Switch)

99-080033 (Guard/Actuator)

99-080038 (Sw. Actuator)

73-3003 ‘—- -2>-——® (Retaining Ring) Figure 3-4 8-Position Joysick Assembly 171021-001

Page 29

Fast Freddie™

To Adjust the Joystick:

  • Make sure that each leaf switch is firmly seated in its holder. There is a small gray plastic tab on the outside end of the switch holder. The black plastic part of each leaf switch must be in front of this tab.
  • Check that all four leat switches can be activated by watching the switch blades as you move the joystick handle up, down, left and right.
  • Test the four diagonal positions. In each diagonal position, iwo leaf switches should close. Switches should continue bending slightly after making contact. Maintenance, Repair and Parts

. Adjust each switch for narrow gap. @ Push the joystick handle away from the switch for easier servicing. @ Use a pair of needlenose pliers or a switch adjustment tool to bend each double set of blades in toward the center. Make the bend where the double set of blades comes out of the black plastic part of the switch. . Recheck the switch action. The switches must move independently for right, left, up, down and diagonal motion of the joystick.

JOYSTICK— TOP REAR VIEW

uP: WHITE/BLACK, BLACK LEFT: BLUE, BLACK

GREY, BLACK DOWN: VIOLET, BLACK

Figure 3-4 8-Position Joystick Assembly, continued Parts List

Part No. Description

73-3003 Retaining Ring 82-AL616 #6 x 1-1nch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 24nch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard/Actuator 99-080036 Top Piate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator 171021-001 Joystick Assembly

3-7

Page 30

Maintenance, Repair and Parts Fast Freddie™

C. Fluorescent Tube and Speaker

A—warninc—, Prior to removing or repairing the speaker or fluorescent tube, unplug the game. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

To Remove the Tube and Speaker Board: 1. From the back of the game, unlock and open the rear access panel. The tube and speaker harness has a 5-pin connector. Unplug this connector. . Open the control panel (see Figure 3-2, The Control Panel). . From the top front of the game, remove the five button-head screws that secure the upper cabinet grille to the cabinet. Lift the grille up and away from the cabinet. Be careful glass display shield doesn’t fall forward. . Lift the display shield up and out of the cabinet. . Slide the baffle board that is underneath tne fluorescent tube out the front of the cabinet.

  • Remove the screws that secure the tube and speaker board to the cabinet. Slide this board up and out of the cabinet.

To Replace Fluorescent Tube:

  • Remove the Y-lead conneciors at each end of the fluorescent tube.
  • Slightly rotate the tube up or down, and carefully remove it from its clamps. Replace it with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the Y-lead connectors. Reinstall the tube and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

To Replace The Speaker:

  • Unplug the two plug-in connectors on the back of the speaker.
  • Remove the hardware that attaches ihe speaker to the board. Replace the speaker and reinstall the hardware and two plug-in connectors. Reinstall the tube and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

3-8 iN 038226-01 (Grille)

038217-01 (Baffle Board)

038689-01 (Shield)

Figure 3-5 Fluorescent Tube and Speaker

Page 31

Fast Freddie™ Maintenance, Repair and Parts

Disassemble in the order indica- 038151-01 ted. (Circled numbers match the (Jmpr. Wire) numbered instructions.)

99-11012 (Clamp)

038219-03 (Light & Spk:. Ba)

99-11009 (Socket)

99-11003 (Starter)

142028-002 (Transformer)

(Speaker)

A038253-01 (Harness)

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to the transformer.

Figure 3-5 Fluorescent Tube and Speaker, continued lreland-Built Cabinet A038228-01 A Parts List

Part No. Description

A038253-01 Tube and Speaker Harness Assembly 70-303* 18-Inch, 1-Inch Diameter, 15W Cool White Fluorescent Tube 99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012* 1% -Inch Fluorescent Tube Clamp 035835-01 12-Inch Y-Lead Connector 038151-01 Jumper Wire 038217-01 Baffle Board 038219-03 Tube and Speaker Board 038226-01 Cabinet Grille 038689-01 Display Shield 142028-002 50 Hz 118V Ballast Transformer 148001-001 6x 9Inch 4-Ohm 15W Oval High-Fidelity Speaker

  • Acceptable substitutes are part numbers 70-304 (tube) and 99-11011 (clamp). They must be used together.
Page 32

Maintenance, Repair and Parts Fast Freddie™

D. Video Display

  • WARNING -— Shock Hazard The following procedure should only be performed by a qualified service technician. Prior to removing or repairing the video display, unplug the game. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. High voltages may exist in any video display, even with power disconnected. Use extreme
caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Implosion Hazard lf you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any display. To Remove Video Display:
  • Open the rear access panel and unplug the three display harness connectors and disconnect the green ground wire.
  • The rear of the display chassis is attached to a mounting bracket. Remove the hardware that secures the chassis to this bracket.
  • Open the control panel (see Figure 3-2).
  • Remove the 5 button-head screws that secure the upper cabinet grille to the cabinet (see Figure 3-5), Lift the grille up and away from the cabinet.
  • Lift the video display shield up and out of the cabinet. 6, Carefully remove the cardboard bezel. 7, Remove the four sets of hardware that secure the display chassis to the wood frame. 8, Carefully remove the display through the front of the cabinet. After servicing the display, reinstall in reverse order. >

@) 03822601 (Grille)

(Shield) 92.049 © 038232-01 (Video Display) —- 037750-01 ¥ OK (Bracket) Disassemble in the order indicated. (Circled numbers match the Figure 3-6 Video Display, continued numbered instructions.) lreland-Built Cabinet Parts List

Part No. Description

92-049 19-Inch Electrohome Color Raster-Scan Video Display (Acceptable substitute is part no. 92-055—use with TM-201) 037750-01 Display Mounting Bracket 038226-01 Upper Cabinet Grille 038232-01 Display Bezel 038689-01 Display Shield with Graphics

3-10

Page 33

Fast Freddie™

E. Coin Door

170000-001 (Lamp)

179047-001 (Lamp Base)

99-15056 (Screw for Bezel)

99-15025 (Coin Inlet)

PART OF

99-15055

75-914S (Hex Nut) (Hex Nut) 750 (Lock Wash.)

99-15031 (Sw. Adjuster)

(Bracket) 99-15026 (Coin Inlet)

is ‘s 99-15068 S (Lockout Coil) 99.15069 a (Lockout < Coil Spring)

(Switch) Maintenance, Repair and Parts

99-15023 (Base Plate)

~~ 9915054 (Pivot for Lever)

<— 99-15060 (Sw. Cover)

T24414S (Screw)

Figure 3-7 Vertically Mounted Coin Door A037619-xx D

Page 34

Maintenance, Repair and Parts

99-15073 (Upper Door)

9915063 (Screw)

99-15067 (Lock Assy}

A037491-01 (Coin Box)

A037542-01 (Harness—not shown)

‘A037619-01 — U.S. 25¢/25¢ Coin Door ‘A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door ‘A037619-05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢/20¢ Coin Door 99-15067.

A037619-08 — German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door A037619-10 — German 2 DM/5 DM Coin Door ‘A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — 5 Fr/5 Fr Coin Door A037619-13 — Swiss 1 Fr/1 Fr Coin Door A037619-14 — French 1 Fri1 Fr Coin Door (Lock Assy.) Zz Fast Freddie™

99-15038 (Bezel for Button)

99-15001 thru 99-15011 (Ret. Button)

9915072 (Door Frame)

99-15071 (Clamp)

(Bezel for Cover)

99-15036 (Cover)

99-15068 (Screw)

90-15074 {Lower Door)

‘A037619-15 — French 2 Frit Fr Coin Door ‘A037619-16 — Swedish 1 Kr/1 Kr Coin Door A037619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door A037619-19 — Hong Kong $1/$1 Coin Door A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-7 Vertically Mounted Coin Door, continued

Page 35

Fast Freddie™ Maintenance, Repair and Parts

Figure 3-7 Vertically Mounted Coin Door, continued Parts List

Part No. Description A037491-01 Coin Box (Not included in assembly) A037542-01 Harness Assembly 72-1414, #4-40 x /,-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-8148 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with \talian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15031 Switch Adjuster 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x_%_-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

Page 36

Maintenance, Repair and Parts

F. Printed-Circuit Boards A— warninc—A,

Prior to removing or repairing any printed-circuit board, unplug the game.

To Remove Printed-Circuit Boards:

  • Open the rear access panel.
  • Locate the hardware that secures the PCB to the cabinet, and remove this hardware. (Each PCB has one screw and two spacers to secure it.)
  • If you are removing the game board, unplug the edge connector. If you are removing the Regulator/Audio II PCB, disconnect the four small harness connectors on this board. Fast Freddie™

|. Carefully remove the PCB from its retainers. Be careful not to twist the boards, as this may loosen connections or components. Repair as required. . Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit only one way, so if they don't slip on easily, don’t force them. A reversed connector will probably damage your game and void the warranty. . Replace the hardware that secures the PCB to the cabinet wall. Close and lock the rear access panel. ’. Check that the operation of the game is correct by performing the self-test. This is very important when you repair a PCB. Unless you are a qualified technician, do not turn any knob on a PCB.

Remove in the order (Circled numbers numbered instructions.)

REGULATOR AUDIO II PCB

75.07017 (Spacer)

(Foam Pad)

72-6610S (Screw) 034536-02 (Foam Pad)

175004-708 (Spacer)

+t (6) 72-6810S (Screw)

© came pce

Figure 3-8 Printed-Circuit Board Removal

Page 37

drawing any ri drawing ig corporation's written license, tionally issued, permission ot Atari, Inc., NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specific written transfers any fight in, or license to use, the subject matier of the manulacture by vendors of Atari, Inc..and fof manutacture under the fr the Subject matter thereof, unless by writen agreement with or written permission from the corporation t to reproduce this drawing or any part thereof. Except for no right is granted to reproduce this and neither receipt nor possession thereof confers or ‘or any design or technical information shown thereon, nor ‘Sunnyvale, CA, This drawing is only cond'-

Figure 3-9 Fast Freddie PCB Assembly 171026-001

3-15 = r x © = 7 ™ ° ° ea

Gikks5 caupice7 mess |= a<39 Gbceo ‘Guz <4: cmcss ccm | ag WEI ie he ve,

| 18.4 lsat han A a ae a met a =e w Liven 06 [arene (OD

CART 1734 2732 » (Essel [ {eee Ts7¢ «[TSIeI (ETT, [is2g5< ame? =

[et-s 0a ioral. sy ‘R37 asl AY-3-8410 ¢ o [tsote [ist [isaze [sey «lem ALI [si38 @« Are CEI cee eRe = (isa tsi 0 [0S3a [Es062 LS74 L574 ¢ [Le3e7¢ (isBe iaaee [eae moen swt ee o» [0S%03 [iseoe [Eston [see [eee «(see [SRETR [Be ow. § : Tee =| mies 350054 g ores = EE o» [i320 [qilseo Ts00¢ [13070 Te3ze [Sse = [sae 4 [(lsseT e™! (Tasca 8

comeee = ELEM lars atee Ge O muncs: Sap ~ [ee ~Ritsooe TSO tSIST os LS00( [1536a £5273 153680 TER, ea Peg Cuacse = Fal 13377 iTS 3B JELEXETS Teseee & 17 RD COR oR cee ‘nau Bee ie i | i © ([es8ee [isco rsee ¢ [15273 0 TOR TST S08 (2508 °@ [rsse8t By,

mes: = GEIRT7 Ea oo tsies ¢ [27Ls00¢ tsie3 ¢ [2eic-ie (£5745 ¢ [TsisTe LSO2 $259 S367 ¢ (19245 en loco uF

DIB0C z-80

» (ieee (isooe (isms (isisTe [ose Ph ples

” Lsis7 ¢ [_ isieT¢ [15157 ¢ [zgic-ie [15245 ¢ [19307¢ [Zil4ic-{¢ [Lsi3e¢ [1s138¢ oa 186 ¢ [15273 L520 LS273 (57840 [£S3e7¢ [24le-1 [320 LSS

foray L3i57 L157 ¢ [15157 3437 L528% 15157 ¢ [£5139 15367

jeeee) OTe O7e0c ¢

CIR (esie7Te =[os37¢ sisTe

ey 2132 q 21342 2732

“4 SIG Tsa4e (E5194 e i col Gi] Co? Clee) 2132 2732 2732 2732

TSia4 ESI94S |siie

cseCTe) coe) ceo ray] 2732 2132 2132 bisa 5) 2782

Ls 94 rS194 <5] ‘ cer Trlces cco = iec70 Ae} Gae<72, GRE}C73, Fast Freddie™ Maintenance, Repair and Parts

Page 38

Maintenance, Repair and Parts Fast Freddie™

Figure 3-9 Fast Freddie PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 24-250108, 1000 uF, + 20%, 16V (min) Axial Aluminum Electrolytic Capacitor (C1, 2) 31-1N914 75V Type-1N914 Switching Diode (D1-3) 37-7408 Type-7408 Integrated Circuit (C9) 37-74LS00 Type-74LS00 Integrated Circuit (F7, J4, K6, M7) 37-74LS02 Type-74LS02 Integrated Circuit (A4, E10, J6, M3) 37-74LS08 Type-74LS08 Integrated Circuit (B4, D9, K7, M8) 37-74LS10 Type-74LS10 Integrated Circuit (J3) 37-74LS20 Type-74LS20 Integrated Circuit (D12, K5, K12, M5, M6) 37-74LS32 Type-74LS32 Integrated Circuit (F14, H6, K3, K4, M4) 37-74LS74 Type-74LS74 Integrated Circuit (E9, F4, F5, H3, H4, L3) 37-74LS86 Type-74LS86 Integrated Circuit (E6, H5, J5, K2, K9, M9, M12) 37-74LS139 Type-74LS139 Integrated Circuit (D13, J2, J3) 37-74LS157 Type-74LS157 Integrated Circuit (E13, E14, F10, H14, J7, J8, K11, K13, L117, L13, M11, M13) 37-74LS161 Type-74LS161 Integrated Circuit (H1, H2, K1, L1) 37-74LS163 Type-74LS163 Integrated Circuit (K10, M10) 37-74LS174 Type-74LS174 Integrated Circuit (L4)

37-74LS175 Type-74LS175 Integrated Circuit (D8) 37-74LS194 Type-74LS194 Integrated Circuit (F15-17, H15-17) 37-74LS245 Type-74LS245 Integrated Circuit (B10, C2, H10, H11) 37-74LS259 Type-74LS259 Integrated Circuit (D10)

37-74LS273 Type-74LS273 Integrated Circuit (C7, J9, J12, K8, L12) 37-74LS367 Type-74LS367 Integrated Circuit (B13, C5, C6, C10, C13, E4, E5, F11, F12) 37-74LS377 Type-74LS377 integrated Circuit (E8) 37-74LS393 Type-74LS393 Integrated Circuit (C8) 62-001 SPST Momentary Pushbutton Switch (A13) 66-118PIT 8-Station, SPST, Dual-Inline-Package Switch (B5) 79-42C16 16-Contact Medium-Insertion-Force integrated Circuit Socket (H7-9) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A14, A16, A17, C14, C16, C17, D16, D17, E1, F1, J14, J16, J17, L14, L16, L17, M14, M16, M17) 79-42C40 40-Contact Medium-Insertion-Force integrated Circuit Socket (B11-12, D5-7) 90-7036 Random-Access Memory (D2, D3, E11, E12, J10, J11) 110000-101 100 Ohm, +5%, %4W Resistor (R25, 29, 29-31, 56, 58, 62) 110000-102 1K Ohm, +5%, %4W Resistor (R52, 53, 59, All Pull-Up Resistors) 110000-103 10K Ohm, +5%, VW Resistor (R43) 110000-221 220 Ohm, +5%, %W Resistor (R9-24, 39, 40, 55, 57, 61, 78, 79) 110000-224 220K Ohm, +5%, YW Resistor (R1-6) 110000-471 470 Ohm, +5%, YW Resistor (R26, 51, 54, 60) 118001-102 1K Ohm, 8-Element, 9-Pin, Single-Inline Package Resistor Network (RM1-3) 119003-102 1K Ohm, + 20%, Horizontal Trimpot (VR1-4) 121015-104 0.1 pF, + 10%, Radial-Lead Ceramic Capacitor (C10, 11, 15-30, All Bypass Capacitors) 121020-101 100 pF, +5%, Radial-Lead Mica Capacitor (C32) 123004-470 47 uF, + 20%, 16V (min) Aluminum ElectrolyticCapacitor (C4, 6, 31) 123004-471 470 uF, + 20%, 16V (min) Aluminum Electrolytic Capacitor (C12) 133011-001 50V, 400mW NPN Transistor (TR2-4) 136009-101 Programmable Read-Only Memory 1 (D16)

3-16 [Continued on next page]

Page 39

Fast Freddie™ Maintenance, Repair and Parts

Figure 3-9 Fast Freddie PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 136009-102 Programmable Read-Only Memory 2 (D17) 136009-103 Programmabie Read-Only Memory 3 (C14) 136009-104 Programmable Read-Only Memory 4 (C16) 136009-105 Programmable Read-Only Memory 5 (C17) 136009-106 Programmable Read-Only Memory 6 (A14) 136009-107 Programmable Read-Only Memory 7 (A16) 136009-108 Programmable Read-Only Memory 8 (A17) 136009-109 Programmable Read-Only Memory 9 (E1) 136009-110 Programmable Read-Only Memory 10 (F1) 136009-111 Programmable Read-Only Memory 11 (M17) 136009-112 Programmable Read-Only Memory 12 (M16) 136009-113 Programmable Read-Only Memory 13 (M14) 136009-114 Programmable Read-Only Memory 14 {L17) 136009-115 Programmable Read-Only Memory 15 (L16) 136009-116 Programmable Read-Only Memory 16 (L14) 136009-117 Programmable Read-Only Memory 17 (J17) 436009-118 Programmable Read-Only Memory 18 (J16) 136009-119 Programmable Read-Only Memory 19 (J14) 136009-120 Programmable Read-Only Memory (H7) 136009-121 Programmable Read-Only Memory (H8) 136009-122 Programmable Read-Only Memory (H9) 137168-001 Type-74LS368 Integrated Circuit (B6-9, E7, F6, M2) 137 169-001 Type-74LS107 Integrated Circuit (L2) 137170-001 Random-Access Memory (L5-10) 137177-001 Type-74LS 138 Integrated Circuit (A13, C3, C4, C11, C12, D11) 137 194-001 Z80 Microprocessor (D5:7, B11, B12) 137204-001 Type-74LS283 Integrated Circuit (H12, H13) 137222-001 Type GI AY3-8910 Sound Integrated Circuit (B1, B3) 137234-001 Audio Amplifier Integrated Circuit (AMP1) 137211-001 2Kx8 Static Random-Access Memory (D414) 137235-001 Custom Chip (E16, 17) 144000-002 18.432 MHz Crystal (M1)

  • ee c ev" bmn a

3-17

Page 40

Maintenance, Repair and Parts

i) M 05, Ro Bax APSE R29 R33 peers o a

"Teeat 3aQ
iERTA3

= G2 8 8 = oO ae

C20c2!0ac

N cig N 3300 — 35V

5300 + ; C23 c3l 35V GeeF} 22}

R25eer}ez
7CSCe
  • 08 Oop 7812 7905

© Oo 33 4R24,10, 7 Wl &

+ fle ©

mS og Fast Freddie™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This Grawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, oF I- Gense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

Figure 3-10 Regulator/Audio II PCB Assembly

3-18 A035435:06 B

Page 41

Fast Freddie™ Maintenance, Repair and Parts

Figure 3-10 RegulatoriAudio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

19-100P10150.1 Ohm, +3%, 7W Wirewound Resistor(R24)

19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) Acceptable substitute is part no. 119002-102. 24-250108 1000 uF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13)

24-250477470 uF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C1)
24-35022622 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C24, 31)
24-350338,3300 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C18, 19)

24-500105 1 uF 50V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C22, 23)

29-0880.1 uF 50V Ceramic-Disc Axial-Lead Capacitor(C20, 21)
31-1N4002Type-1N4002 100V 1-Amp. Silicon Rectifier Diode(CR1, 4)

31-1N5401 Type-1N5401 100V 3-Amp. Silicon Rectifier Diode (CR5-8)

33-TIP32Type-TIP32 PNP Power Transistor(Q2)
34-2N3055,Type-2N3055 NPN Silicon Transistor(Q3)
37-LM3055V Linear Voltage Regulator(Q1)
37-7812Type-7812 + 12V Voitage Regulator(Q8)
37-7905Type-7905 —5V Voltage Regulator(Q9)

72-1608C #6-32 x Ye-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw

72-6810S#8 x %4-Inch Phillips-Head Wood Screw(for mounting PCB to cabinet)

75-F60405 #6-32 x ¥Va-Inch Binder-Head Nylon Screw 75-99516 #6-32 NutWasher Assembly

78-16014Thermally Conductive Silicon Insulator(Q2, 9)

79-58306, 6-Position Connector Receptacle (J6, 9)

79-58308,9-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)

034531-01 Heat Sink 034536-02 Foam Vibration Damper (goes between PCB and cabinet wall) 110000-100 10 Ohm, +5%, %W Resistor (R29, 30)

110000-101100 Ohm, +5%, %W Resistor(R4)
110000-271270 Ohm, +5%, %4W Resistor(R1)
110000-33033 Ohm, +5%, %W Resistor(R3)

410000-392 3.9K Ohm, +5%, %4W Resistor (R6) 110000-562 5.6K Ohm, +5%, %4W Resistor (R32, 33)

110000-7527.5K Ohm, +5%, Y4W Resistor(R7}
110009-0272.7 Ohm, +5%, 1W Resistor(R5)

116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 116001-040 4 Ohm, +5%, 5W Wirewound Resistor (R25)

122002-102.001 uF 50V Ceramic-Disc Axial-Lead Capacitor(C2)

122004-224 .22 uF 25V (min.) Ceramic-Disc Axial-Lead Capacitor (C8) 175004-708 Fiber Spacer (for mounting PCB to cabinet) 179051-001 Test Point (Acceptable substitute is part no. 020670-01)

3-19

Page 42

Maintenance, Repair and Parts Fast Freddie™

G. Power Supply Assembly

A035888-01 (Transformer) 29.053 (Capacitor)

A021084-01, -04 & -05

WARNING a (Vol. Sel. Plug) Fuse cover must be in place during game a operation. paasaain (Cover)

79-4411001 (Fuse Post) 78-70501SC (Capac, Bracket} 46-2017002 (Fuse)

A035891-01 (Fuse Harness)

46-301203 (Fuse)

(Label)

78-2708 (Hole Bushing)

79-3206 (Fuse Block} A034630-01 (RFI Filter)

037641-01 (Label) 46-2014002 (Fuses)

79-15021001 ‘A035890-01 (Term't Block) \ (Pwr. Harness) ‘A034629-01 epecien,, (AC. Harness) Figure 3-11 Power Supply Assembly A037671-02 C

3-20

Page 43

Fast Freddie™ Maintenance, Repair and Parts

Figure 3-11 Power Supply Assembly, continued Parts List

Part No. Description (Reference Designations in Bold) A021084-01 Voltage Plug for 100V (violet)

A021084-04Voltage Plug for 220V_(b/ue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly = (FL1) A035888-01 Transformer Assembly (11) Acceptable substitute is part no. A035888-02 03589001 Power Harness Assembly A035891-01 Fuse Harness Assembly A037671-02 Power Supply Assembly 29-053 27,000 pF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014002 4-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 037243-01 Metal Base Plate (goes under the power supply—not shown in illustration) 037639-01 Label for Fuse Value (F1)

037641-01Label for Fuse Values(F2-F6)

Line Voltage Range 90-110 VAC (100) 200-240 VAC (220) 220-260 VAC (240) Voltage Selection Plug Wire Color Violet Blue Brown

3-21

Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 45

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

\f you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name,

Firm C Distributor

Address ©) Operator City Country Gi Other.

Phone: CountryCode______ Local Number Fast Freddie™ 1st printing

Page 46

First fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland

Second fold

‘WOs4 eBpe siyy adey

Page 47

@ Ny ° i ° >

> Yili Nata, Sates, Natal, Sates Satelit Sates 3

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under norma{ use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted

lf the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration. improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. :

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others, Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible tor the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used. or disclosed to persons not having a need to know consistent with the purpose of the oan, without written consent of Atari, Inc. BEI BE IDEA TEBE EGE EGE © « © « © © © BS

Page 48

ATARI INC 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035, 408/942-3100 ¢ TELEX 35-7488