CATHODE RAY TOMES

Dig Dug TM-202 Euro 1st Printing

Dig Dug (rev 2) (Namco, 1982) · Technical Manual · 52 pages · 47 sections · original scan

Page 1

TM-202 \ {st printing

e s s - . . . ' ‘ . . moan Nie = Operation, Maintenance and Service Manual ala eMiciae: tian, Ary Yt eee Complete with Illustrated Parts Lists Bey a Ss . % . tts = . - . s 4 a al s . 5 o

a bE a A 2 aie r = "5 . a ty . = . bg 2 f = + = . See ;

Fr e im . "3 | . ij . i . i . ty . ce . = . oe = 4 . aie ‘

Page 2

GAME SERIAL NUMBER LOCATION

Your game's serial number is stamped on a label on the outside back of the P r )

Page 3

Operation, Maintenance

and Service Manual

Complete with lilustrated Parts Lists

Engineered and Designed by NAMCO, LTD. Manufactured by ATARI, INC.

Page 4

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Dig Dug™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. if infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 3L

Page 5

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the following:

  • you substitute non-ATARI parts in your coin-operated game, or
  • you modify or alter any circuits in your ATARI game by using kits or parts not supplied by ATARI.

Not only may the use of any non-ATARI parts void your warranty, but any such alteration may also adversely aifect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

1 Set-Up Procedures A. New Features... 0. ccc cen eee B. Game Inspection C. Game installation . see : :

  • Installation Requirements .................-0005
  • Voltage Selection ...... D. Switch Locations .
  • On/Off Switch .
  • Utility Switches ........
  • Option Switches ....... Option Switch Settings Self-Test Procedure . Game Play ....... . Attract Mode .... . Ready-to-Play Mode . PlayMode ........ . High Score Mode .. omm

ARON

2 Troubleshooting A. Introduction 6.0... 6.6 B. Comments on Troubleshooting . C. Self-Test Procedure ........ 6... e cece e ee eee

3 Maintenance, Repair and Parts Cabinet Mounted Assemblies The Control Panel ......... Fluorescent Tube and Speaker . Video Display ............... Vertical-Mounted Coin Door .. . Printed-Circuit Boards ..... ONMOSODD>S . Hints forGame Play ..... 00.60. cece

Power Supply Assembly ........... 2.00 cece eee eee neers 2-2

Page 7

List of Illustrations

Figure 1-1 Game Overview . 1-2 Figure 1-2 Game Switch Locations . .. 14 Figure 1-3 Self-Test Procedure ....... -. 17 Figure 2-1 Self-Test Screen 1-Test PasseS .........-. 0... cece eee eee eee 22

Figure 2-2 Self-Test Screen 1-Test Fails .............0. 00 ccc eee eee eee 23 Figure 2-3 Self-Test Screen 2 2.00... 0. ccc cece cece eee eee 23

Illustrated Maintenance, Repair and Parts: Figure 3-1 Cabinet-Mounted Assemblies Figure 3-2 TheControl Panel .................- Figure 3-3 Control Panel Assembly . Figure 3-4 The Joystick Control

Figure 3-5 Fluorescent Tube and Speaker Figure 3-6 Video Display.............. Figure 3-7 Vertical-Mounted Coin Door . . Figure 3-8 Printed-Circuit Board Removal

Figure 3-9 Dig Dug™ Central Processing Unit PCB Assembly ..............- 315 Figure 3-10 Dig Dug Video PCB Assembly Figure 3-11 Regulator/Audio || PCB Assembly o Figure 3-12 Power Supply Assembly ....... 20.0000. e cece cece e eee eee y

Table 1-1 Game Price and Bonus Option Settings ..................200005 Table 1-2. Game Difficulty, Price and Special Options oe Table 1-3 DigDugScoring........... 0... ccc eee eee ete eee

Page 8
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Service only

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii +" (408) 745-2900 = Service from anywhere in the area shown in white €@ ‘toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey COs (201) 469-5993 exw From anywhere else in this area toli-free (800) 526-3849

EUROPE Service only

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

@ 0062-52155

vi

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and serv ice technicians, describes the Dig Dug™ game.

Chapter One includes new features, game set-up, option switch settings, self-test procedures and game play.

Chapter Two details troubleshooting procedures.

Chapter Three contains maintenance, repair and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

A. New Features

The Dig Dug™ game has two new features. Even if you're familiar with ATARI® games, you should note these important differences: @ Joystick Control. This new four-position control is made of steel and molded plastic. It has few parts, which make servicing easier. The leaf switches snap in and out for easy replacement. The rubber bellows is designed for a quick return to center. @ Game Cabinet. The Dig Dug cabinet has several new features. The cabinet grille is both a speaker grille and display-shield retainer. In addition, the upper part of the display shield also serves as the attraction panel. These new features, as well as all other major parts in the game, are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you wil! see this symbol:

“~S

Chapter

Page 10

Dig Dug™ Set-Up Procedures

FLUORESCENT TUBE AND SPEAKER See Figure 3-5

ACCESS PANEL

See Figure 3-6

oN

CONTROL PANEL { ‘CENTRAL PROCESSING

CONTROL PANEL UNIT (CPU) PCB ee Figure 3-2 & 3-3 { See Figures 3-8 & 3-9 JOYSTICK | oe VIDEO PCB See Figure 3-4 , © 3 See Figures 3-8 & 3-10

REGULATOR! AUDIO I PCB See Figures 3-8 & 3-11

POWER ON/OFF SWITCH POWER SUPPLY See Figure 3-12 UTILITY PANEL See Figure 1-2

Figure 1-1 Game Overview

Page 11

Set-Up Procedures

WARNING SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

B. Game Inspection

it

2. Please inspect your game carefully to insure that was delivered to you in good condition.

NOTE Do not plug the game in yet!

. Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCBs are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood slot at the bottom of the tear panel opening.

WARNING To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands! @ Note the location of the game’s serial number—it is printed on the special label on the back of the game cabinet. Verify that the serial numbers also stamped on the Dig Dug™ game PCBs, Regulator/Audio Il PCB, power supply and video display are all identical. A drawing of the serialnumbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and video display for secure mounting.

C. Game Installation

  • Installation Requirements

Power 140 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 79 cm (25% x 31 in.) Game Height 174 cm (68% in.)

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any Country in the world. The power supply has three different voltage selection plugs: 100 VAC (violet wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).

Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for your location’s line voltage (see Figure 3-12).

1-3

Page 12

Dig Dug™ Set-Up Procedures

D Switch Locations is used to credit the game without tripping the coin

counter. These switches are located inside the upper coin door (see Figure 1-2).

  • On/Off Switch 3. Option Switches The on/off switch is located on the back of the Option switches are located on the game central cabinet, lower left side (see Figure 1-2). processing unit (CPU) PCB: oT 7 @ Game price and bonus options are at CPU PCB
  • Utility Panel Switches location 8D. The utility panel includes the volume control, self- @ Game difficulty, price and special options are at test, coin switch, and coin counter. The coin switch CPU PGB location 7D.

UTILITY PANEL:

COIN COUNTER

SELF-TEST

ean OPTION SWITCHES: Hieber COIN POWER ONIOFF SWITCH Scene presen bonus options) SWITCH AT 7D (Game difficulty, price and special options)

Figure 1-2 Game Switch Locations

Page 13

Set-Up Procedures

E. Option Switch Settings

Tables 1-1, Game Price and Bonus Options and 1-2, Game Difficulty, Price and Special Options detail game options and their settings. Options are

Table 1-1

The 8-toggle switch at location 8D is accessible when the Dig Dug™ CPU PCB is mounted in place. To change switch settings, set the self-test switch to on. Verify the changes on the self-test screen. Then turn the self-test switch to off. preset at the factory and shown by the $ symbols. However, you may change the settings to suit your individual needs.

Game Price and Bonus Option Settings

A “coin” is defined as 1DM or 1Fr. If you have a 2DM/1DM or 2Fr/1Fr coin door with two coin counters, set switch 8 at CPU PCB. focation 7D to off. Then different denominations are counted on the two coin counters.

Settings of 8-Toggle Switch on Dig Dug CPU PCB (at 8D)

234567

1 8 Option

OnOnOn
OnOnOff

On Off On

On Off Off Off On On

Off On Off

OffOffOn
OffOffOff
OnOnOn
OnonOff
OffOffOn
OffOffOff

On On Off On. On Off Off Off Right coin mech—coin doors with 1 or 2 coin counters* 1 coin for 7 credits 1 coin for 6 credits 1 coin for 3 credits 1 coin for 2 credits

1coin for 1 credit $ 2 coins for 3 credits 2 coins for 1 credit 3 coins for 1 credit

Bonus lives awarded at the following point values: With 1, 2 or 3 Dig Dug lives With 5 Dig Dug lives No Bonus No Bonus First at 10,000, First at 20,000, second at 40,000, second at 60,000, and every 40,000 $ and every 60,000 First at 10,000, First at 30,000, second at 50,000, second at 80,000, and every 50,000 and every 80,000 First at 20,000, First at 20,000, second at 60,000, second at 50,000 and every 60,000 First at 20,000, First at 20,000, second at 70,000, second at 60,000 and every 70,000 First at 10,000, First at 30,000, second at 40,000 second at 70,000 First at 20,000, First at 20,000 second at 60,000 First at 10,000 First at 30,000

1 Dig Dug life 2 Dig Dug lives 3 Dig Dug lives $ 5 Dig Dug lives

$Manufacturer's suggested settings

  • See Table 1-2 for left coin mechanism
Page 14

Table 1-2 Game Difficulty, Price and Special Options The table below contains the switch settings for options relating to game difficulty, price and special options. The switches, ‘on the CPU PCB at location 7D, are accessible when the PCB is, mounted in place. Set-Up Procedures

“>

A special option allows for continuation of game play. If a player is at a more advanced round when his game ends, he has 16 seconds to begin the next game at the same round. Another special option allows you to freeze the game action.

Settings of 8-Toggle Switch on Dig Dug CPU PCB (at 7D) 2 7 8 Option 1 3 4 5 6

On On On Off

Off On

Off Off On Off On Off

Off On

On On On Off

Off Off A—Easy game difficulty B—Medium game difficulty $ C—Hard game difficulty D—Expert game difficulty

Continuation of game play $ No continuation of game play Attract Mode sound $ No Attract Mode sound

Normal game action $ Freeze game action

Left coin mech—coin doors with 2 coin counters * 1 coin for 1 credit $ 1 coin for 2 credits 2 coins for 1 credit 2 coins for 3 credits

On One coin counter $ Off Two coin counters *

$Manutacturer's recommended settings *Coin doors with different denominations and two coin counters.

F. Self-Test Procedure

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary.

We suggest you run the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure.

Refer to Figure 1-2 for the location of the self-test switch and option switches. To run the self-test, set the self-test switch to on. After about eight seconds the self-test screen will be displayed.

To see game statistics, press the utility coin switch. To reset the high score table, simultaneously push and hold the pump and utility coin switches for 10 seconds. To end the seif-test, set the self-test switch to off.

The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. If any part of the test described in Figure 1-3 fails, refer to Chapter 2. Wa J,

Page 15

Set-Up Procedures Dig Dug™

Figure 1-3 Self-Test Procedure

Instruction Test Passes

  • Set the self-test switch to on (see Figure 1-2). Patterns appear on the screen. After about 8 seconds, the screen displays the picture below. The RAMs, ROMs and other chips are tested. If the picture is different from the picture below, refer to Chapter 2, Self-Test Procedure.
  • Activate any control panel switch. Game sounds are produced, from SOUND 00 through SOUND
  • Activating any control panel switch produces a new sound. Test all switches this way. If test fails, refer to Chapter 2, Seif- Test Procedure. Game sounds: SOUND 00 Credit issued SOUND 01 Start of game SOUND 02 Indication of highest score SOUND 03 Game over SOUND 04 Monster attacking Dig Dug SOUND 05 Dig Dug dies SOUND 06 Monster escaping SOUND 07 Bonus Dig Dug awarded SOUND 08 End of wave SOUND 09 Monster speeding up SOUND 10 Monster crushed by rock SOUND 11 Monster bursting SOUND 12 Rock hitting ground SOUND 13 Rock falling SOUND 14 Dragon spitting fire SOUND 15. Dig Dug throwing harpoon SOUND 16 Dig Dug pumping up monster

SOUND 17 Dig Dug walking SOUND 18 Monster moving SOUND 19 Dig Dug capturing vegetable SOUND 20 Enter initials into high score table

ALL RAMS GOOD

ALL ROMS GOOD

TYPE OF CABINET UPRIGHT

LEFT COIN MECH >1 COIN 1 CREDIT RIGHT COIN MECH 1 COIN 1 CREDIT

NO. OF LIVES

DIFFICULTY

SOUNDS 1ST BONUS FOR 10000 PTS 2ND BONUS FOR 40000 PTS ~<— BONUS LEVELS GAME STATISTICS: AND FOR EVERY 40000 PTS THE COUNT STARTS AT 999999) AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 99 .9999 .9999 .9999 .9999. 99.9 and the display shows 98.9 for the number of games played. (Disregard decimal points.)

NO. OF GAMES NO. OF POINTS NO. OF SECONDS NO. OF BONUS

PLAYED SCORED PLAYED LIVES AWARDED

1-7

Page 16

G. Game Play

The Dig Dug™ game is a one- or two-player game with a color raster-scan video display. The screen shows a cutaway view of the land, most of which is below ground. The player controls the Dig Dug character who travels through and digs tunnels in the dirt. The object is for Dig Dug to capture vegetables and destroy monsters by pumping them up or dropping rocks on them.

Dig Dug has five possible modes of operation: attract, ready-to-play, play, high score and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (all credits will be cancelled).

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode is continuous and stops only when a credit is entered, or when in self-test. This mode may last for about one minute and fifteen seconds. In the attract mode, the screen displays one of four possible pictures.

In the first picture, Dig Dug enters the screen from the top right and walks across the surface. He digs a tunnel into the ground and begins to dig around the words DIG DUG. Meanwhile, monsters escort the word ATARI across the top of the screen. When Dig Dug digs entirely around the words DIG DUG, these words, ATAR/ and the monsters fall down to a new position on the screen. Everything in the picture rolls up except the words DIG DUG.

In the second picture, game characters appear on the screen. Dig Dug is between FYGAR, the firebreathing dragon, and POOKA, the fat monster. First, Dig Dug pumps up POOKA until he explodes and disappears, and 200-500 (points) appears in his piace. Then, Dig Dug pumps up FYGAR until he explodes and disappears, and 200-1000 appears in his place.

The third picture simulates game play. Dig Dug walks through underground tunnels. Monsters chase him and he periodically pumps them up or drops rocks on them. This picture ends when Dig Dug is caught (touched) by a monster.

The fourth picture shows the high-score table. The top five scores, round played and matching initials appear on the screen.

During the attract mode, the high score and score(s) for one or both players appear at the top of the screen. Credits or number of Dig Dug lives and

1-8 Set-Up Procedures

the round number appear at the bottom of the screen. This mode ends when coins are inserted and accepted for game play.

  • Ready-to-Play Mode

During this mode, the high score and score(s) for one or both players appear at the top of the screen. The words PUSH START BUTTON, 1 PLAYER ONLY or 1 OR 2 PLAYERS and bonus life information appear in the center of the screen. ATARI copyright, credits and the round number appear near the bottom of the screen. This mode ends when a player pushes the start button.

  • Play Mode

This mode begins when Dig Dug enters the screen from the top right and walks across the surface. He digs down to the center of the screen. The words PLAYER 1 READY or PLAYER 2 READY appear on the screen. Also, high score and score(s) for one or both players appears at the top of the screen. The number of Dig Dug lives and the round number appear at the bottom of the screen.

Game play takes place on a cutaway section of the land. The characters are Dig Dug and two monsters, one of which is a fire-breathing dragon. The underground area is divided into four different colored layers of dirt. Rocks are scattered in the dirt. The sky is at the top of the screen.

The player controls Dig Dug. He moves through horizontal and vertical tunnels. When Dig Dug digs new tunnels he moves slowly. When he is on the surface or in an existing tunnel, he moves faster. The object of the game is for Dig Dug to destroy all the monsters and go to the next round.

Page 17

Set-Up Procedures

Monsters are trapped in caves. Amonster may get out of a cave two ways. Dig Dug may dig him out. Then, the monster chases Dig Dug. The monster may also get out of the cave by turning into a ghost. As a ghost, he cannot be destroyed. The ghost does not travel in the tunnels. He travels through the dirt, and can travel diagonally. However, he reappears as ihe monster when he goes into a tunnel.

The monster moves faster than Dig Dug in vertical tunnels and slower on the surface. He destroys Dig Dug by catching him. In addition, the dragon destroys Dig Dug by breathing fire on him. The dragon only breathes fire horizontally. The fire can penetrate the dirt.

Dig Dug destroys the monsters by pumping them up until they burst, or by causing rocks to drop on them. To pump up and destroy a monster, the player presses and holds down the pump button. It is possible to stun a monster for a few seconds by pressing the pump button once or twice. While a monster is stunned, Dig Dug may pass over him without being destroyed. If two monsters are very close together, only one may be stunned. The other will catch and destroy Dig Dug.

Dig Dug must dig tunnels under the rocks to get them to drop. A rock may fall in a vertical or a hori- Zontal tunnel. A rock also goes through a thin layer of dirt from one tunnel to the next. In a vertical tunnel, Dig Dug may stay directly under a rock and it will not drop. However, in a horizontal tunnel, Dig Dug must move out from under a rock right away, or he will be crushed.

After two rocks are dropped, a vegetable (worth extra points) appears in a tunnel in the center of the screen. A player has 10 seconds to capture (touch) the vegetable or it will disappear. There is only one vegetable per round.

The game progresses by rounds. Round 1 starts with four monsters and three rocks. The vegetable is a Carrot. One flower on the surface (top right of the screen) represents Round 1. Two flowers represent Round 2, etc. As the rounds progress, the monsters move a little faster, and are better at avoiding falling rocks. In each round, the last monster tries to escape. If he is not caught by Dig Dug, he exits on the surface (top left).

The game ends when all of the Dig Dug lives are used up. A player may continue to play at the same round (level) by following instructions on the screen. He has 16 seconds to insert a coin(s). Then he must push and hold the pump and start buttons at the same time.

  • High Score Mode This mode begins when a player has one of the five top scores. A player enters his initials in the center of the screen. The initials are then transferred to the table. To reset the high-score table, set the self-test switch to on. Simultaneously push and hold the pump and utility coin switches for 10 seconds. Then set the self-test switch to off.
  • Hints for Game Play @ Get many monsiers to follow you. Then dig a long vertical tunnel up to a rock. Drop the rock by digging right or left. @ Dig Dug may take extra time to turn. It is better to start turning early than to wait until the last second. @ Destroy monsters at bottom dirt level for more points. @ Use PUMP to stun monsters. Then you may escape or walk through them. @ Don't stop next to dragon when he is in a cave. His fire can go through a thin layer of dirt and destroy you. @ A vegetable appears after two rocks have been dropped. So be sure to drop two rocks in each round.

1-9

Page 18

1-10 Table 1-3 Dig Dug Scoring

Bursting Monsters

Dirt Layer POOKA 1 200 2 300 3 400 4 500 “Worth 2 amount vertically

Dropping Rocks

Monsters Destroyed

Vegetables

Round Vegetable 1 Carrot 2 Rutabaga 3 Mushroom 4 Cucumber 5 Cucumber 6 Eggplant 7 Eggplant 8 Bell Pepper Q Bell Pepper 10 Tomato an) Tomato 12 Onion 13 Onion 14 Watermelon 15 Watermelon 6 Galaxian 7 Galaxian 18 Pineapple 19 Pineapple 20-30 Pineapple

Digging a new tunnel is worth 10 points per *, inch (1.61 cm). Points 1000 2500 4000 6000 8000 10,000 12,000 15,000

Points for Capture

1900 1000 2000 2000 3000 3000 4000 4000 5000 Set-Up Procedures

Page 19

Troubleshooting

A. Introduction

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 1 is to help you decide if the game is or isn’t working properly. The expanded procedures in this chapter are included to help the qualified electronic technician determine why the game isn’t working properly.

If you are not a qualified technician, do not try to work on the game circuitry or video display. True, it is not earning money when it doesn't work. However, your investment in this game may greatly increase if either the video display and/or game PCB are destroyed while you are working inside the game cabinet. Be assured, it isn’t worth it.

Page 20

B. Commments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II PCB, or the video display?

The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.

When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair is relatively simple, as these assemblies are not too complicated. If a game PCB is failing, troubleshooting and repair will greatly depend on your understanding of the operation of this PCB.

To effectively troubleshoot problems of a game PCB, it is necessary for you, the technician, to become familiar with the PCB’s hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting this PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.

C. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. Patterns appear on the screen. After about 8 seconds, the self-test screen is displayed (see Figure 2-1). See Chapter 1, Section F, Self-Test Procedure for a complete description of this part of the self-test.

NOTE This procedure does not test the coin door lockout coils. If the self-test passes, but the lockout coils do not energize when the self-test switch is set to off, suspect the lockout coil wiring, coin door harness, game PCB harness, or latch 7J of the CPU PCB.

RAM OK ROM OK UPRIGHT 1 COIN 1 CREDIT 1 COIN 1 CREDIT DIGDUG 3 RANK C SOUND 04 1ST BONUS FOR 10000 PTS 2ND BONUS FOR 40000 PTS AND FOR EVERY 40000 PTS

Figure 2-1 Self-Test Screen 1 Test Passes

Page 21

Troubleshooting Dig Dug™

To go to screen 2, set the self-test switch to off and immediately to on again.

SCREEN 2:

Figure 2-2 Self-Test Screen 1 A white crosshatch pattern appears on the screen Test Fail (see Figure 2-3). Use this pattern for convergence est Fails (see the raster-scan video display manual).

SCREEN 1:

RAM FAILURE is indicated by the word RAM and a pair of alphanumeric characters displayed at the top of the screen. The following table lists the bad RAM chip and its location. Bad RAM chip location Screen Display on Video PCB RAM OL 2E RAM OH 2e RAM 1L 2E RAM 1H 2E RAM 2L 3N RAM 2H 2N RAM 3L 3L RAM 3H aL RAM 4L 3M RAM 4H 2M

ROM FAILURE is indicated by the word ROM and anumber displayed at the top of the screen. The folowing table lists the bad ROM chip and its location.

Bad ROM chip location Screen Display ‘on CPU PCB ROM 1 3P ROM 2 3M ROM 3 2M ROM 4 2b ROM 5 oF ROM 6 w . ROM 7 2c Figure 2-3 Self-Test Screen 2

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Maintenance, Repair and Parts

In addition to maintenance and repair information, this chapter provides the necessary information for you to order parts for your Dig Dug game. Please note that common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598-thru approximately 190000-.

When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed in the front of this manual for your convenience.

Chapter

Page 24

Dig Dug™ Maintenance, Repair and Parts

A. Cabinet-Mounted Assemblies

Fluor. Light & Speaker— 7 Figure 3-5 » Self — a ‘see Figure a Schematics, Self-Test Label & Manuals: see parts list on following page

03822601(Cabinet Assy.)p1gag

(Grille)

Video Display—: see Figure 3-6 037332-01 Grille) wes 038223-01 (Shield) 178034-024 (T-Molding)

178013-001 =

(Latch)371-2110

(Lock)

<t®"037721-02
Control Panel Assy.— {7Yj‘Panel

Fae (Access Panel) see Figures 3-2 & 3-3 §

A038004-01 (Util. Sw. Harn.)

‘see Figures 3-8 & 3-10

Coin Door Assy.—4oe—CPU PCB Assy.—

see Figure 3-7 see Figures 3-8 & 3-9

‘A038250-01 (Main Harn. Assy.)

A037491-01 (Coin Box)

Power Supply Assy.—:é=a«.

eg./Audio Il PCB Assy.— see Figure 3-12 : 54 see Figures 3-8 & 3-11

x ‘A002465.01 : : (Coin Counter) we >

19.9032>te

p= ee.

(Vol. Ctrl)4y

62.041 (Coin Sw.)

69-00178-3201# Sy

. Le

(SeltyTest Sw)(Leg)‘A037470-01 i

038003-01 (On/Off Sw.) (Util. Brit.) 178048-001

(Caster)009992-01‘A037454-03

(On/Off Sw. Cvr.) (Power Cord)

Figure 3-1 Cabinet-Mounted Assemblies

3-2 A038203-01 A

Page 25

pee Maintenance, Repair and Parts. Dig Dug™

Figure 3-1 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A002465-01 Coin Counter A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly A038205-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) A038250-01 Main Harness Assembly The following four items are the technical information supplements to this game: SP-202 Dig Dug™ Schematic Package ST-202 Dig Dug Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display TM-202 Dig Dug Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 78-3201 Cabinet-Leveling Leg 009992-01 On/Off Switch Cover 036686-01 Card of Game Pricing Labels (not shown in illustration) 037721-02 Rear Access Panel (does not include lock) 037332-01 Ventilation Grille (located on cabinet top) 038003-01 Utility Bracket for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038208-01 Side Panel Decal (not shown in illustration) 038223-01 Video Display Shield with Graphics 038226-01 Upper Cabinet Grille 178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 Rigid Caster

Page 26

B. The Control Panel A— WARNING

Prior to removing or repairing any switch on the control panel, unplug the game.

To Open the Control Panel:

  • Open the coin door. Reach up through the opening and release the spring-draw latches. They are on the cabinet side walls at each end of the control panel.
  • Lift up on the control panel at the top edge, and tilt it toward you. The control panel edge next to the display shield has foam tape applied to it. The tape cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.

Leaf Switch Repair: @ Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner. © To replace a leaf switch, remove the screw with a Phillips-head screwdriver. @ To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design. Maintenance, Repair and Parts

© Reinstall the switch. Reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs ‘on the switch.

LED Start-Switch Replacement: The LED switches have a very low failure rate. If a switch should ever be suspect, first test it using the directions that follow.

To Test LED Switch:

@ Remove the wires from the suspected switch. @ Attach the leads of an ohmmeter to normally open and common contacts. @ Check contacts (push and release the switch button) for closed and open continuity. @ if the contacts do not operate sharply or always remain closed or open, then replace the LED switch.

To Replace LED Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.

BROWN() NORMALLY OPEN

The CONTACT RED(+ 1 Eek Be hiton CONTACT

START 2

YELLOW NORMALLY OPEN (N.O.) CONTACT ORANGE(-) nxn —t BLACK COMMON CONTACT

Figure 3-2 The Control Panel

3-4 a

Page 27

Maintenance, Repair and Parts Dig Dug™

! WARNING ! Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the A038230-01 (Cont. Pni/Decal) 295-04 _ ground wire is firmly attached to the metal tab beens chains a4 on the inside of the control panel. Only then 038224-01 should you lock up the game. {Cont. Pat) 78-6900402 ie 62-039 (Start Sw.)

N 036895-01 (Bezel)

178030-003 75-9910NO (Pushbtn. Assy) (Nut)

A038252-01 160013-001 (Harness) (Leaf Sw/Btn. Hidr.)

Figure 3-3 Control Panel Assembly, continued Parts List

Part No. Description A038230-01 Control Panel with Decal A038231-01 Control Panel Assembly A038252-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Start Switch, with Red Light-Emitting Diode 75-9910NO #5,-11 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, Y-Inch wide x %-Inch thick (24 in. required) 036895-01 Black Molded Switch Bezel 038224-01 Control Panel 038225-04 Control Panel Decal 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 171016-001 Joystick Assembly 178030-003 Black Pushbutton Assernbly

A038231-01 A

Page 28
WARNING

Prior to removing or repairing the joystick, unplug the game.

To Repair the Joystick:

  • First, remove the entire joystick assembly from the control panel (see Figure 3-3). Now locate the four screws in the plastic joystick frame and remove these screws.
  • Next, remove the clip ring from the bottom of the shaft. The assembly will come apart.
  • To replace the bellows, pry it up and out of the plastic frame. @ Reassemble in reverse order. @ Note that the inner raised ring on the bellows is longer on one side. This side goes on the top of the assembly (toward the control knob).
  • To replace a /eaf switch, you don’t need to disassemble the joystick. @ Using your thumbs, pry apart the plastic flanges on the switch holder. With your index finger, lift the switch up So that it will clear the plastic tab located on the outside end of the switch holder. @ Slide the switch out of its holder. Replace the switch in reverse order. Adjust the switch for a narrow gap.

99-080031 (Bellows)

99-080032 Disassemble in the order indi- (Steel Washer) cated. (Circled numbers match the numbered instructions.)

99-080030 (Spring) ee ] 99-080034 (Sw-Plate)

82-AL616 (Screw) Maintenance, Repair and Parts

“aS

99.080028 (Shaft)

99-080026 (Washer)

99-080035 (Top Plate)

99-080029 (Washer)

99-080025 (Switch)

99-080033

99-080027 (Sw. Actuator)

73-3003 ~ D> @ (Ring)

Figure 3-4 Joystick Assembly

171016-001 (Guard Actuator) ~~ gee

Page 29

Maintenance, Repair and Parts Dig Dug™

UP: WHITE/BLACK, BLACK JOYSTICK TOP REAR VIEW

LEFT: BLUE, BLACK

DOWN: VIOLET, BLACK

RIGHT: GREY, BLACK

Figure 3-4 Joystick Assembly, continued Parts List

Part No. Description 73-3003 Retaining Ring 82-AL616 #6 x 1-Inch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 2-Inch Black Plastic Washer 99-080027 Nylon Switch Actuator 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard Actuator 99-080034 Switch Mounting Plate 99-080035 Top Plate

Page 30

Maintenance, Repair and Parts

C. Fluorescent Tube and Speaker

WARNING Prior to removing or repairing the speaker, fluorescent tube or fan, unplug the game. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

To Remove the Tube and Speaker Board: 1. From the back of the game, unlock and open the rear access panel. The tube and speaker harness has a 5-pin connector. Unplug this connector. Open the control panel (see Figure 3-2, The Control Panel). From the top front of the game, remove the five button-head screws that secure the upper cabinet grille to the cabinet. Lift the gritle up and away from the cabinet. Be careful glass display shield doesn't fall forward. Lift the video display shield up and out of the cabinet. Slide the baffle board that is underneath the fluorescent tube out the front of the cabinet.

  • Remove the screws that secure the tube and speaker board to the cabinet. Slide this board up and out of the cabinet.

To Replace Fluorescent Tube:

  • Remove the Y-lead connectors at each end of the fluorescent tube.
  • Slightly rotate the tube up or down, and carefully remove it from its clamps. Replace it with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the Y-lead connec: tors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the contro! panel and the rear access panel.

To Replace The Speaker:

  • Unplug the two plug-in connectors on the back of the speaker.
  • Remove the hardware that attaches the speaker to the board. Replace the speaker and reinstall the hardware and two plug-in connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

3-8 038226-01 : (Grille)

038217-01 (Baffle Board)

038223-01 - (Shield)

Figure 3-5 Fluorescent Tube and Speaker

Page 31

Maintenance, Repair and Parts Dig Dug™

Disassemble in the order indica- 038151-01 ted. (Circled numbers match the (Jmpr. Wire) numbered instructions.)

99-11012 (Clamp)

038219-03 (Light & Spkr. Ba)

99-11009 (Socket)

99-11003 Gtarter)

142028-002 (ranstormer 03563501 \ (9) (Connector) 148001-001 (Speaker)

©

‘A038253-01 (Harness)

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to the transformer.

Figure 3-5 Fluorescent Tube and Speaker, continued Parts List

Part No. Description

A038228-01 Fluorescent Tube and Speaker Assembly A038253-01 Light and Speaker Harness 70-303* 18-Inch Long, 1-Inch Diameter, 15W Cool White Fluorescent Tube 99-11003 Fluorescent Lamp Starter 99-11009 Starter Socket 99-11012* 1% -Inch Fluorescent Tube Clamp 035835-01 12-Inch Y-Lead Connector 038151-01 Jumper Wire 038217-01 Baffle Board 038219-03 Light and Speaker Board 038223-01 Display Shield 038226-01 Cabinet Grille 142028-002 50 Hz 118V Ballast Transformer 148001-001 6x9-Inch 4-Ohm 15W Oval High-Fidelity Speaker

  • Acceptable substitutes are part numbers 70-304 (tube) and 99-11011 (clamp). They must be used together.

A038228-01 A 3-9

Page 32

D. Video Display

WARNING Shock Hazard The following procedure should only be performed by a qualified service technician. Prior to removing or repairing the video display, unplug the game. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. High voltages may exist in any video display, even with power disconnected. Use extreme
caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any display. Maintenance, Repair and Parts

To Remove Video Display:

  • Open the rear access panel and unplug the three display harness connectors.
  • The rear of the display chassis is attached to a mounting bracket. Remove the hardware that secures the chassis to this bracket.
  • Open the control panel (see Figure 3-2). 4, Remove the 5 button-head screws that secure the upper cabinet grille to the cabinet (see Figure 3-5). Lift the grille up and away from the cabinet.
  • Lift the video display shield up and out of the cabinet. 6 Carefully remove the cardboard bezel.
  • Remove the four sets of hardware that secure the display chassis to the wood frame.
  • Carefully pull the display out through the front of the cabinet. After servicing the display, reinstall in reverse order.

038223-.01 @ (Shield)

Bezel 92.049 (eoz2) ( (video Display)

Disassemble in the order indicated. (Circled numbers match the ® 038226-01 (Grille)

(Bracket)

Figure 3-6 Video Display numbered instructions.) P arts Li ist

Part No. Description

92-049 19-Inch Electrohome Color Raster-Scan Video Display 037750-01 Display Mounting Bracket 038223-01 Display Shield with Graphics 038226-01 Upper Cabinet Grille 038232-01 Display Bezel

310 VA038203

Page 33

Maintenance, Repair and Parts Dig Dug™

E. Vertical-Mounted Coin Door

170000-001 (Lamp)

179047-001 (Lamp Base)

99-15040 ~~ 99-15026 (Lever) 99-15056 (Coin intet) (Screw for Bezel)

PART OF 99-15041 9915055 f -

(Reing. Screw) ay

oe

99-15027 (Coin Ret, Box) 99-15054 (Pivot for Lever) 99-15041 {Lockout Coil) { 99.15053 (Lockt. Cot! Spring)

[+ 99-5028 (Coin Ret. Box)

99-15056 (Screw for Bezel) (Sw. Adjuster)

99-15060 -—- (Sw. Cover) 99-15029 (Bracket)

(Switch)

Figure 3-7 Vertical-Mounted Coin Door

AOS7EIGxx B 311

Page 34

99-15070 (Door and Frames

99-15067 (Lock Assy.)

99-15063 (Screw)

03754201 (Harness—not shown for clarity)

A037619-01 — U.S. 25¢/25¢ Coin Door A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — lan 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door A037619-05 —- British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢/20e Coin Door 99-15067 (Lock Assy,)

99-15036 (Cover)

‘A037619-08 — German 1 DM/1 DM Coin Door A037619-09 — German 2 DM/1 DM Coin Door A037619-10 — German 2 DMIS DM Coin Door , ‘A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — 5 Fr/5 Fr Coin Door ‘A037619-13 — Swiss 1 Fri1 Fr Coin Door A037619-14 — French 1 Frit Fr Coin Door (Bezel for Cover) Maintenance, Repair and Parts

99-15038 (Bezel for Button)

99.15001 thru 99-15012 (Ret. Button)

99.15052 (Spring for Button)

99-15065 (Clamp)

99-15066 (Screw)

\ A037491-01 (Coin Box)

‘A037619-15 — French 2 Fri1 Fr Coin Door ‘A037619-16 — Swedish 1 Kri1 Kr Coin Door A037619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door ‘A037619-19 — Hong Kong $1/$1 Coin Door ‘A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-7 Vertical-Mounted Coin Door, continued

3-12 A037619-xx B

Page 35

Maintenance, Repair and Parts Dig Dug™

Figure 3-7 Vertical-Mounted Coin Door, continued Parts List

Part No. Description A037491-01 Coin Box A037542-01 Harness Assembly 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005, Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Piate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 ‘Switch Bracket 99-15030 Flap for Lockout Coil (U.S, 25%) 99-15036 Metal Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S, 25¢ 99-5052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15065, Clamp for Frame 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Door and Frame 170000-001 6.3V Miniature Wedge Base Incandescent Lamp 179047-001 Lamp Base

3-13

Page 36

F. Printed-Circuit Boards

WARNING Prior to removing or repairing any printedcircuit board, unplug the game.

To Remove Printed-Circuit Boards:

  • Open the rear access panel.
  • Locate the hardware that secures the PCB to the cabinet, and remove this hardware. (Each PCB has one screw and two spacers to secure it.)
  • If you are removing the game boards, first unplug the edge connector. Then unplug the small harness connector on each PCB. If you are removing the Regulator/Audio 11 PCB, disconnect the two small harness connectors on this board. Maintenance, Repair and Parts

. Carefully slide the game PCBs straight out of their slots, or slide and lift the Regulator/Audio II PCB out of its slot. Be careful not to twist the boards, as this may loosen connections or components. Repair as required. Reinstall the PCB, making sure that the connectors are Properly plugged in. Note that they are keyed to fit only one way, so if they don’t slip on easily, don’t force them. A reversed connector will probably damage your game and void the warranty. Replace the hardware that secures the PCB to the cabinet wall. Close and lock the rear access panel. Check that the operation of the game is correct by performing the self-test. This is very important when you repair a PCB. Unless you are a qualified technician, do not turn the knob near the CPU PCB’s edge connector. Also do not turn the small knobs on the Regulator/Audio II PCB.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

@ viveo Pca

171018-001 (Interconnector)

@ cpu pcs

Figure 3-8

3-14 75-07017 (Spacer)

(Screw)

  • REGULATORI AUDIO Ii PCB

Printed-Circuit Board Removal

Page 37

Maintenance, Repair and Parts

MeO 780C

cae 47M tev meeose f custom o& Pay a cat GD am ee

teesa] Saaer] aD car

ay o Sau] Sunes

parr @at

5 mma, pees _—) oes eee ee

M9, era

Ras [——)

custom 08 lh 0: EMI BEOKe

& Fos iy custom 53

custom 08

Figure 3-9 Dig Dug™ Central Processing Unit PCB Assembly

171019-001 eal #8 cas. oP su om sw

= Ge

Ge cH & ie

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specilic written. permission of Atari, Inc., Sunnyvale, CA. This drawing is oniy condi: tionally issued, and neither receipt nor possession thereot conters or transfers any right in, or license to use, the subject malter of the ‘drawing oF any design oF technical information shown thereon, nor any fight to reproduce this drawirg or any part thereot. Except lor ‘manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement, with or written permission from the corporation.

3-15

Page 38

Maintenance, Repair and Parts

Figure 3-9 Dig Dug™ Central Processing Unit PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 24-160107 100 pF, 16V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C22)

24-16022622 uF, 10V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C20)
24-160227220 uF, 10V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C1, 21, 48)
24-25010610 uF, 10V Aluminum Electrolytic Fixed Axial-Lead Capacitor(C25, 44)
31-1N914Type-1N914 75V Switching Diode(D1)

33-2N3906 Type-2N3906 Transistor (Q2) 34-2N3904 Type-2N3904 NPN 60V, 1W Transistor (Q1) 37-4066 Type-4066 Quad Analog Switch Integrated Circuit (8N) 37-7404 Type-7404 Integrated Circuit (7P) 37-74LS32 Type-74LS32 Integrated Circuit (1D, 1L) 37-74LS74 Type-74LS74 Integrated Circuit (7K)

37-74LS139Type-74LS139 Integrated Circuit(1C, 4E, 1M)
37-74LS157Type-74LS157 Integrated Circuit(5M)
37-74L8174Type-74LS174 Integrated Circuit(7M)
37-74LS259Type-74LS259 Integrated Circuit(5K)
37-74LS273Type-74LS273 Integrated Circuit(6N)
37-74LS367Type-74LS367 Integrated Circuit(1E, 2E, 1F, 2F, 1J, 2J, 1K, 2K)

37-74LS393 Type-74LS393 integrated Circuit (8M) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package DIP Switch (7D, 8D) 72-6610S #6 x Inch Phillips-Head Screw (for mounting PCB to cabinet wall) 75-07017 Spacer for Mounting Printed Circuit Board 79-42C16 16-Contact Medium-Insertion-Force Integrated Circuit Socket (5N, 7N)

79-4202424-Contact Medium-Insertion-Force Integrated Circuit Socket(2C, 2D, 3F, 3J, 2L, 2M, 3M, 3P)
79-4202828-Contact Medium-insertion-Force Integrated Circuit Socket(4C, 4D, 5J, 4L, 5P)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(1A, 3A, 1P)
79-42C4242-Contact Medium-insertion-Force Integrated Circuit Socket(5D, 5F)

79-58243 3-Position Connector, Amp 350429-1 (J2) 90-7005 Random-Access Memory (6L, 6M) 034536-02 Foam Vibration Damper 110000-101 100 Ohm, +5%, %W Resistor (R5) 110000-102 1K Ohm, +5%, %W Resistor (R6, 16, 52-54, 60, 62, 66, 70-74) 110000-103 10K Ohm, +5%, %W Resistor (R7, 8, 10, 19, 51, 55)

110000-104100K Ohm, +5%, %W Resistor(R13)

110000-222 2.2K Ohm, +5%, vaW Resistor (R17) 110000-223 22K Ohm, +5%, %4W Resistor (R11) 110000-331 330 Ohm, +5%, ‘4W Resistor (R1, 2) 110000-332 3.3K Ohm, +5%, Y4W Resistor (R20)

110000-471470 Ohm, +5%, %4W Resistor(R15, 47, 48)

110000-472 4.7K Ohm, +5%, YW Resistor (R18, 65) 110000-473 47K Ohm, +5%, %4W Carbon Resistor (R12)

118000-221220 Ohm, 4-Station, 8-Pin, Single-Inline-Package Resistor Pack(RM16)
118000-2222.2K Ohm, 4-Station, 8-Pin, SingleInline-Package Resistor Pack(RM10-13)
118001-1021K Ohm, 4-Station, 5-Pin, Single-Inline-Package Resistor Pack(RM1-5, 9, 24)
118001-2222.2K Ohm, 4-Station, 5-Pin, Single-Inline-Package Resistor Pack(RM20, 23)

3-16 [Continued on next page]

Page 39

Maintenance, Repair and Parts Dig Dug™

Figure 3-9 Dig Dug™ Central Processing Unit PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

118002-1021K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM6, 7)
118002-2222.2K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM17-19)
118002-4724.7K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM21, 22)

119003-102 1K Ohm Trimpot (VR1)

121014-4754.7 uF, 16V Tantalum Capacitor(C62-67, 77-80)

121015-101 100 pF, 50V Ceramic Capacitor (C45, 46, 103)

121015-103.01 uF, 50V Ceramic Capacitor(C2-17, 19)

121015-104 -1 pF, 25V Radial-Lead Ceramic-Disc Capacitor (C18, 49-61, 68, 71, 73, 74, 81-101)

121015-222.0022 uF, 50V Ceramic Capacitor(C43)
121015-33033 pF, 50V Ceramic Capacitor(C47, 102)

121018-154 .15 uF, 25V Solid Aluminum Capacitor (C23, 24)

131009-0016.2V, 1W Zener Diode(D5)

136007-101 Programmable Read-Only Memory, DD11 = (3P)

136007-102Programmable Read-Only Memory, DD1 2(3M)
136007-103Programmable Read-Only Memory, DD13(2M)

136007-104 Programmable Read-Only Memory, DD14 = (2L) 136007-105 Programmable Read-Only Memory, DD15 = (3F)

136007-106Programmable Read-Only Memory, DD1 6(3d)
136007-107Programmable Read-Only Memory, DD17(2C)
136007-109Programmable Read-Only Memory, DD1-1(5N)
136007-110Programmable Read-Only Memory, DD1-2(7N)
137169-001Type-74LS107 Integrated Circuit(6P)
137177-001Type-74LS138 Integrated Circuit(4K, 5L)
137186-001Multi-CPU Bus Controller Custom Chip 08(4C, 4D, 4L)
137187-001Coin and 1/0 Controller Custom Chip 51(5F)

137188-001 Steering Controller Custom Chip 53 (5D)

137192-001Controller Custom Chip 06(5J)
137193-001Sync Generator Custom Chip 07(5P)
137194-0014.0 MHz Z80A Central Processing Unit(1A, 3A, 1P)
137202-001Type-74128 Integrated Circuit(8L)
137203-001Type-74LS158 Integrated Circuit(6K)
137204-001Type-74LS283 Integrated Circuit(7L)
137213-001Transistor Array Integrated Circuit, ULN-2064B(7J)
137215-001Audio Amplifier Integrated Circuit(8A)

144000-002 18.432 MHz Crystal (X1) 171015-001 CPU PCB, Video PCB, and Interconnector 171018-001 §0-Pin PCB Interconnector 171019-001 CPU PCB Assembly

175005-001M#3 Steel Flat Washer(8A)
175006-001M#3 Split Lock Washer(8A)
176014-112M#3 x 12mm Phillips-Head OvalH Metric Screw(8A)
177005-001M#3 x 0.5 Plated Steel Hexagon Metric Nut(8A)
179095-05050-Pin Connector, Fujitsu FCN-705P050-AU/M(J1)

179096-050 50-Pin Jack, Fujitsu FCN-707J050-AU/M

3-17

Page 40

Dig Dug™ Maintenance, Repair and Parts

654321
c2eceo18cis
3ooSooeoe

<a Re 25 C1815

Sox 9

4 {aaa}oe en KeeEne

¢ ey

eeslks 6frregNerees

phelaty Fa PE «

5sskeeds este on 1®[_exzess 3[reve ae

5s8333:0) Now Mv ray ene

2.228Tee

iseeg Me 8532

rae resee E pacione d Roto (a) es

F _ PETELK

H:noasne[ease

d

zn Rea 1s at ra t

mMeEes32

  • eS Se

measse eas

(om) ieee

L3[Eerere[eronazd[eeamed= [aee5 4 69) ag

3 5

"certGrmawatif)Grae[ees 2 8

ca cas ce cu > ronal

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written Permission of Atari, Inc., Sunnyvale, CA. This drawing is only condi tionally issued, and neither receipt nor possession thereof confers or \ransfers any right in, oF license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right 0 reproduce this, drawing or any part thereot. Except for ‘manufacture by vendors of Atari, Inc., and for manufacture under the ‘corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Figure 3-10 Dig Dug™ Video PCB Assembly

3-18 171020-001

Page 41

Maintenance, Repair and Parts Dig Dug™

Figure 3-10 Dig Dug Video PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 24-160227 220 yF, 10V Aluminum Electrolytic Fixed AxialLead Capacitor (C1, 2) 24-250106, 10 pF, 10V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C34)

31-1N914Type-1N914 75V Switching Diode(D1)

34-2N3904 Type-2N3904 NPN 60V, 1W Transistor (Q1) 37-74LS00 Type-74LS00 Integrated Circuit (1B) 37-74LS08 Type-74LS08 Integrated Circuit (1d)

37-74LS20Type-74LS20 Integrated Circuit(6F, 6J)
37-74LS32Type-74LS32 Integrated Circuit(4C)
37-74LS74Type-74LS74 Integrated Circuit(1A)
37-74LS86Type-74LS86 Integrated Circuit(4D, 3H, WJ, 1K)

37-74$139 Type-74LS139 Integrated Circuit (4F) 37-74LS157 Type-74LS157 Integrated Circuit (4J)

37-74LS161Type-74LS161 Integrated Circuit(4L, 5L, 4M, 5M)
37-74LS 166Type-74LS166 Integrated Circuit(3C)
37-74LS174Type-74LS 174 Integrated Circuit(3B, 6D, 4H)
37-74LS175Type-74LS175 Integrated Circuit(5A)
37-74LS241Type-74LS241 Integrated Circuit(1H)
37-74LS244Type-74LS244 Integrated Circuit(3A)
37-74LS245‘Type-74LS245 Integrated Circuit(1E, 1L, 1M, 1N)
37-74LS257Type-74LS257 Integrated Circuit(6E)

37-74LS259 Type-74LS259 Integrated Circuit (2B) 37-74LS273 Type-74LS273 Integrated Circuit (1D, 3D, 5N)

37-74LS374Type-74LS374 Integrated Circuit(4A)
37-74LS377Type-74LS377 integrated Circuit(4N)
72-6610S#6 x 3-Inch Phillips-Head Screw(for rnounting PCB to cabinet wall)

75-07017 Spacer for Mounting Printed Circuit Board

79-4201616-Contact Medium4nsertion-Force Integrated Circuit Socket(6C, 4E, 6N)
79-42C2020-Contact Medium-insertion-Force Integrated Circuit Socket(SE)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(2C, 5C, 2D, 2E, 5F, 5H, 5J, 5K)
79-42C2828-Contact Medium-Insertion-Force Integrated Circuit Socket(5D, 2F, 2H, 2K)

79-58123 6-Position Connector, Amp 350431-1 (J2) 90-7036 Random-Access Memory (2L, 3L, 2M, 3M, 2N, 3N) 034536-02 Foam Vibration Damper 110000-101 100 Ohm, +5%, %4W Resistor (R19)

110000-1021K Ohm, +5%, %4W Resistor(R1-5, 11, 14, 20)

110000-103 10K Ohm, +5%, vsW Resistor (R9, 10) 110000-221 220 Ohm, +5%, %W Resistor (R13, 16, 18)

110000-471470 Ohm, +5%, %W Resistor(R12, 15, 17)

110001-022 2.2 Ohm, ¥2W Carbon Resistor (R8) 110014-274 27.4K Ohm, +1%, %W Carbon Resistor (R7) 110015-120 1.2K Ohm, + 1%, %W Carbon Resistor (R6)

118001-1021K Ohm, 4-Station, 5-Pin, Single-Inline-Package Resistor Pack(RMS, 10, 12, 15)
118001-2222.2K Ohm, 4-Station, 5-Pin, SingieInline-Package Resistor Pack(RM1, 6)
118001-4274.7K Ohm, 4-Station, 5-Pin, Singleinline-Package Resistor Pack(RM7)

{Continued on next page}

Page 42

Dig Dug™ Maintenance, Repair and Parts

Figure 3-10 Dig Dug Video PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

118002-1021K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM8Q, 11, 13, 14)
118002-10310K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM8)
118002-2222.2K Ohm, 8-Station, 9-Pin, Single-Inline-Package Resistor Pack(RM2-4)

121014-475, 4.7 uF, 16V Tantalum Capacitor (C15, 16, 22-24, 39) 121015-104 1 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C17-21, 25-29, 32, 35-38, 40-48) 121016-475 4,7 uF, 35V Tantalum Capacitor (C31)

121017-10610 pF, + 10%, 16V Tantalum Capacitor(C33)

121019-220 220 pF, 25V Styrol Capacitor (C30) 136007-108 Programmable Read-Only Memory, DD29 (2C)

136007-111Programmable Read-Only Memory, DD1-4(6N)
136007-112Programmable Read-Only Memory, DD1-3(4E)
136007-113Programmable Read-Only Memory, DD1-5(6C)
136007 -125Programmable Read-Only Memory, DD1 10(2D)
136007-120Programmable Read-Only Memory, DD1 11(5C)
136007-121Programmable Read-Only Memory, DD1 15(5K)
136007-122Programmable Read-Only Memory, DD2 14(5d)
136007-123Programmable Read-Only Memory, DD1 13(5H)
136007-124Programmable Read-Oniy Memory, DD1 12(5I
137161-001Electrically Alterable Read-Only Memory(4B)
137168-001Type-74LS368 Integrated Circuit(3F)
137177-001Type-74-LS138 Integrated Circuit(1F)
137189-001Video RAM Addresser Custom Chip 00(2F)
137190-001Universal Shift Register Custom Chip 02(5D)
137191-001Motion Object Controller Custom Chip 04(2K)
137193-001Sync Generator Custom Chip 07(2H)

137198-001 Random-Access Memory (2E) 137199-001 Random-Access Memory (4K, 6M)

137200-001Type-74LS365 Integrated Circuit(6K, 6L)
137201-001Type-74LS298 Integrated Circuit(1C, 3E, 6H)
137204-001Type-74LS283 Integrated Circuit(2J, 3K)

137214-001 Dual-Inline-Package Voltage Regulator, T.|. TL497A (B5) 137216-001 Programmed Array Logic 10H8 (5E) 141004-001 220 wH Inductor (L1) 171020-001 Video PCB Assembly

3-20

Page 43

A035435-05 A 3-21 Figure 3-11 Regulator/Audio Ii PCB Assembly TIwse2 an — [ore a5 bees ce eo7} cR4 Lop INGOC2 Too} Ra = lle 4S \e x24, 19, 2 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction forbidden without the specific wri , Sunnyale, CA, this nett Qt nor

shown thereon, Nor any right

is drawing or any part thereof. Except for

manufacture by vendors of Atari, Inc., and for manufacture

under ine. " fo right is granted ‘matter thereof, unsn permission Maintenance, Repair and Parts

Page 44

Maintenance, Repair and Parts

Figure 3-11 Regulator/Audio || PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

A035435-05RegulatoriAudio Il PCB AssemblyAcceptable substitute is part no. A0354365-01 thru -04.

19-100P1015 1. Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) Acceptable substitute is part no. 119002-102. 24-250108 1000 pF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13) 24-250477 470 uF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C1) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CR1, 4)

33-TIP32PNP Power Transistor, Type TIP32(Q2)

34-2N3055 NPN Silicon Transistor, Type 2N3055 (Q3)

37-LM3055V Linear Voltage Regulator(Q1)

72-1608C #6-32 x Ye-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw (Q3)

72-6610S.#6 x %-Inch Pan-Head Screw(to attach PCB to cabinet)

75-07017 Fiber Spacer (to attach PCB to cabinet)

75-99516,#6-32 Nut/Washer Assembly(Q3)

75-F60405, #6-32 x ‘%-Inch Binder-Head Nylon Screw (Q2)

78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2)

79-583066-Position Connector Receptacle(J6)
79-583089-Position Connector Receptacle(J7)

034531-01 Heat Sink 034536-02 Foam Vibration Damper 110000-100 10 Ohm, +5%, %W Resistor (R29, 30) 110000-101 100 Ohm, +5%, %W Resistor (R4) 110000-271 270 Ohm, +5%, %W Resistor (R1) 110000-330 33 Ohm, +5%, %W Resistor (R3)

110000-3923.9K Ohm, +5%, YW Resistor(R6)
110000-7527.5K Ohm, +5%, YW Resistor(R7)
110009-0272.7 Ohm, +5%, 1W Resistor(R5)

122002-102 .001 pF 25V Ceramic-Disc Minimum Radial-Lead Capacitor (C2) 122004-224 .22 uF 25V Ceramic-Disc Capacitor (C8) 179051-001 Test Point Acceptable substitute is part no, 020670-01.

3-22

Page 45

Maintenance, Repair and Parts Dig Dug™

G. Power Supply Assembly

Line Voltage Range Voltage Selection Plug Wire Color 90-110 VAC (100) Violet 200-240 VAC (220) Blue A035888-01 220-260 VAC (240) Brown (ranstormer)

a A021084-xx (Volt. Sel. Plug) 29.053 (Capacitor) 034544.01 (Fuse Block Cvr.)

79-4411001 Fuse Post) 78-70501SC (Cap. Bracket) ' mL, 46-2017002 = (Fuse)

A035891-01 (Fuse Harness) 034482-02 L (Chassis)

46-301203 (Fuse)

03763901 (Label)

A034630-01 (Filter Assy.)

46-2014002 (Fuses) .

A035890-01 (Pwr. Harness) 78-2708 (Bushing)

79-3206 (Fuse Block) 037641-01 (Label)

79-15021001 (Term. Block)

3A-MDA3501 recannie (Rectifier)

Figure 3-12 Power Supply Assembly

A037671-02 C 3-23

Page 46

Maintenance, Repair and Parts

Figure 3-12 Power Supply Assembly Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(violet)
A021084-04Voltage Plug for 220V(blue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1)
A035888-01Transformer Assembly(11)Acceptable substitute is part no. AO35888-02

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly A037671-02 Power Supply Assembly 29-053 27,000 wF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x ¥-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)

3-24

Page 47

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of game manuals. No postage stamp is necessary if mailed in the U.S.A.

|f you have any technica! questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm © Distributor

Address © Operator City State Zip O Other. 1st printing

Area Code Phone

Page 48

First told

Postage |

Ip Atari Ireland Limited | Attn.: Field Service/Coin-Op Division | Tipperary Town, Ireland |

““gecondtoid ss—=“CSs~=“—s*s—SsSSS ~~ |

WUO4 4 | eBpe siy) ede,

Page 49

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform ta this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing. In no event shall Seller be tiable for loss of profits, loss of use, incidental or consequential damages. .

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.