CATHODE RAY TOMES

Star Wars Cockpit TM-245 1st Printing

Star Wars Cockpit (Atari, Inc., 1983) · Technical Manual · 91 pages · 68 sections · original scan

Page 1

Cockpit sarinins

“s+

©1983 Lucasfilm Ltd. & Atari, Inc. Allrights reserved. *Trademarks of Lucasfilm Ltd. used by Atari, Inc. under license.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, GA 94086 Yelex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska, or Hawaii (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Ine. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08874 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) POW From New Jersey (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland ‘Telex 28-165 TIPPERARY TOWN, (Monday-Friday, 9:¢0-6:00 pm GMT) IRELAND: BS 06252155

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4

STAR WARS COCKPIT

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 6M

Page 5

STAR WARS COCKPIT

Notice Regarding Non-ATARI Parts

Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in. a commercial environment. Operation of this equipment ina residential area or modification to this equipment is likely io cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: © All green ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. © The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents

Set-Up How to Use This Manual . . opt Game Overview ........ 1-4 Installation Specifications . 1-4 Inspecting the Game ..... 1-4 Stabilizing the Cockpit ..... 15 Voltage-Plug Selection and Fuses . 15 Flight Control Calibration . . . 16 Switch Locations .......... 16 Selecting the Game Options ...... 1-7 Game Play.... 19 Attract Mode . . : 19 Select-a-Death Star Mode 110 Play Mode 1-1 High-Score Mode . : : : : . 112 SelfTest Mode ........ a se. H2

Self-Test Self-Test Displays 0.6... c cece cnn neces 2-2

Troubleshooting Troubleshooting Aids 3-2 Troubleshooting Techniques 3-2

Maintenance Cleaning Requirements 42 Opening the Control Panel . 42 Flight Control Maintenance . 43 Removing the CRT Assembly 48 Wiring the Utility Panel Contols. . 49

Illustrated Parts Lists Cabinet-Mounted Assemblies . . STAR WARS Cockpit Decals . Flight Control Assembly . . . Fluorescent Tube and Speakers Assembly . Utility Panel Assembly.........- Vertically Mounted Coin-Door ... American-Made Coin-Door . Power Supply Assembly ... : PCB Mounting Hardware, US-Built Cabinet . . . PCB Mounting Hardware, Ireland-Built Cabinet EMI Shield PCB Assembly Regulator/Audio II PCB Assembly . Main PCB Assembly ...........- Analog Vector-Generator (AVG) PCB Assembly . . bee Sound PCB Assembly ....... 660. c eee cece eee nets

Page 7

List of Illustrations

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 5-1A Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9A Figure 5-9B Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13 Figure 5-14

Table 1-1 Table 1-2 Table 1-3 Table 1-4 Game Overview Stabilizing the Cockpit Cabinet Voltage-Selection Plug and Fuse Locations Switch Locations

Accounting and Game Times Display . . . . Game Options Display . . vee : Hardware Errors Display—Test Passes . . Hardware Errors Display—Test Fails . . Switch Test Display Mathbox Tests Display—Test Passes Mathbox Tests Display—Test Fails . . Crosshatch Pattern Display Grid Pattern Display Intensity Test Display Bipolar Offset Test Display—Test Passes Bipolar Offset Test Display—Test Fails . . Scale Test Linear Display Scale Test Linear and Binary Display . . Raster Screen Display

Handle Assembly . . Steering Assembly . ‘ Removing the CRT Assembly Utility Panel Wire Colors

Illustrated Parts Lists Cabinet-Mounted Assemblies, US-Built Cabinet ... . STAR WARS Cockpit Decals ... 7 Flight Control Assembly... . . . Fluorescent Tube and Speaker Assembly . Utility Panel Assembly . . Vertically Mounted Coin- American-Made Coin-Door . Power Supply Assembly . . . . PCB Mounting Hardware, US-Built Cabinet . « PCB Mounting Hardware, Ireland-Built Cabinet . . EMI Shield PCB Assembly : Regulator/Audio II PCB Assembly Main PCB Assembly . . Analog Vector-Generator (AVG) PCB Assembly Sound PCB Assembly

List of Tables

Installation Requirements Switch Settings for Play Options Switch Settings for Coin and Credit Options .. . Switch-Settings for Special Options

  • 5-12 » 5-14

. 518 « 5-22 . 5-24 » 5-26 . 5-28

  • 5-30 . 5-33
  • 5-38 ++ 5-43 5-2
Page 8

STAR WARS COCKPIT

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

4& WARNINGS A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end ofa large, well-insulated, 20-kV jumper to ground. Momentuarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
Page 9

How to Use This Manual

This manual, written for game operators and service technicians, describes your new Atari game. Wherever information is unique to the Ireland-built game, this symbol appears: Wherever information is unique to the US-built game, this symbol appears: Chapter 1 contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains troubleshooting procedures. Chapter 4 contains maintenance and repair procedures. Chapter 5 contains illustrated parts lists, Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a supplement to this manual.

Page 10

Set-Up STAR WARS COCKPIT

Do not plug in the game until it has been inspected, This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a ground- Printed-Circuit Board ed outlet. Players may receive an electrical shock if this game is not See Figure 5-9 properly grounded! The enclosure contains the: ‘Sound PCB * ‘See Figure 5-14

See Figure 5-13 Main PCB x See Figure 5-12 EMI Shield PCB * See Figure 5-10

Deflection PCB « Used with Atari Display See Display Manual

Regulator/Audio tI PCB * See Figures 5-9 & 5-11

Utility Panel Assy. See Figure 5-5

High-Voltage PCB « Used with Atari Display Power On/Off Switch Power Supply Assy. * See Display Manual See Figure 5-8

1 Item with a serial number label Figure 1-1 Game Overview

1-2

Page 11

ia STAR WARS COCKPIT

Video Display * Canopy Decals See Figure 5-2

Housing and Decal Assy.

Coin Door See Figures 5-6 or 5-7

Figure 1-1 Game Overview, continued Flight Control Assy. See Figure 5-3 Set-Up

Page 12

Set-Up

Game Overview

STAR WARS* is a spectacular video spectacle! STAR WARS is a one-player game, which uses a color X-Y video display. As the player, you'll enter the exciting world of LUKE SKY WALKER* and pilot the RED 5 X-WING* spacecraft to victory over the Empire's evil forces!

New Features Voice-enhanced game play. The voices you will recognize belong to the actual characters of LUKE SKYWALKER, DARTH VADER’, BEN KENOBI", HAN SOLO’, and R2-D2*. They intensify the excitement of swift and dynamic game play. Flight control. The flight control for STAR WARS is a new Auri design. It allows a player to use real flying techniques on a voyage that is out of this world! Tamper-proof screws. There are 12 tamper-proof screws on the cover of the flight control assembly. They prevent abuse of the control or its handles. Flight-control wrench. special wrench for the tamperproof screws is included with your game. It is located in the coin box. Medium-speed, medium-resolution, cathode-ray tube. This new XY cathode-ray tube (CRT) produces exceptionally clear graphics for the world of LUKE SKYWALKER.

Options display. The Self-Test program of STAR WARS includes an options display that enables you to select game options without having to set the option switches from the back of the cabinet. See Chapter 2 for more details.

All major parts of the STAR WaRS cabinet are illustrated in Figure 1-1.

Installation Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Requirements

Characteristic Requirement

Power Consumption 250 W Nominal Temperature 0° to +38° C(+32° to +100° F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC (for both cabinets) Width 64.1 cm (25.25 in.) Depth/Length 186.7 cm (73.5 in.) Height 141 cm (59.5 in.)

  • ©1983 Lucasfilm Ltd. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. STAR WARS COCKPIT

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCBare firmly plugged into their sockets. c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Inspect the power supply. Make sure the fuse block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, EM] cage, and each PCB. Make sure they are mounted securely and that the green ground wires are connected.
Page 13

STAR WARS COCKPIT

Stabilizing the Cockpit

The STAR WaRs cabinet rolls easily from location to location on 4-inch casters. To stabilize the cabinet, lift the game up onone side. Place a block of wood, a book, or another object at least 2-inches thick under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-2) until they extend below the caster. Lower the game and lift the other side. Partially unscrew the adjustable glides until they extend below the caster. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.

Voltage-Plug Selection

and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-3). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire

20A,32V

FUSES F4-F6 4A, 250V Set-Up

Caster x Adjustable Glide

o— Figure 1-2 Stabilizing the Cockpit Cabinet

colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-3 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

VOLTAGE-SELECTION PLUGS

Fuse cover is shown in Figure 5-8

Figure 1-3 Voltage-Selection Plug and Fuse Locations

Page 14

Set-Up

Flight Control Calibration

The STAR WARS game has a self-calibrating flight control. The game circuitry monitors the position of the cursor on the display in relation to the flight control vertical and horizontal position. Calibration is quickly accomplished by moving the cursor to all four extreme edges of the display. Calibrating is also accomplished during normal game play, but may take a few seconds to optimize.

Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1),

Utility Panel Switches

The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1). STAR WARS COCKPIT

The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-4 and 5-5 for details of these switches. Option Switches STAR WARS has three option switches. These switches are dual-inline-package (DIP) switches located on the Main printed-circuit board (PCB). Figure 1-4 shows the location of these switches on the Main PCB. If your game is built in the U.S., the Main PCB is set in the electromagnetic interference (EMI) cage. If your game is built in Ireland, the Main PCB is set in the PCB housing (see Figure 5-9). ° The option switch at 10D is for selecting play options.

  • The option switch at 10E/F is for selecting coin and credit options. © The option switch at IL is for selecting special options.

Auxillary Coin Switch

Self-Test ‘Switch Game PCB

Interconnect moO “ OFF im H on Cc

oer C4 et wp ( ot

Figure 1-4 Switch Locations “—

Page 15

STAR WARS COCKPIT

Selecting the Game Options

Settings for option switches are listed in Tables 1-2, 1-3, and 1-4. Options preset at the factory are shown by the <4 and

  • symbols; however, you may change settings according to your needs.

To verify other option selections, check the self-test display that appears when you turn on the game. Then, verify the option-switch settings on the self-test display as described in Chapter 2. Table 1-2 lists settings for the DIP switch at 10D. This switch is used to select play options (such as the number Set-Up

of starting shields per game). Table 1-3 lists settings for the DIP switch at 10E/F. This switch is used to select coin and credit options available for the left and right coin mechanisms. Table 1-4 lists settings for the DIP switch at 11L. This switch is used to select aspecial option for the way coin outputs are handled by the game.

The basic unit of measurement is a coin worth $.25 or 1 DM. Thus, if you have a 2 DM/1 DM coin door with two coin counters, set switch 1 at location 11L to OFF. Then, different denominations are counted on the two coin counters.

Table 1-2 Switch Settings for Play Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10D) 1 2 3 4 5 6 7 8 Option

On Off On Off On On Off Off

On Off On Off On On Off Off

On Off On Off On On Off Off

On Off 6 Starting Shields 7 Starting Shields 8 Starting Shields 9 Starting Shields

Easy game play Moderate game play Hard game play Hardest game play

0 Bonus Shields for Destroying Death Star 1 Bonus Shield for Destroying Death Star<4 2 Bonus Shields for Destroying Death Star 3 Bonus Shields for Destroying Death Star

Music in the Attract Mode<t No Music in the Attract Mode

On Off Freeze Mode Normal Game Play Mode~<4

“dManufacturer’s recommended settings

1-7

Page 16

Set-Up STAR WARS COCKPIT

Table 1-3 Switch Settings for Coin and Credit Options

‘8-Toggle Switch on Star Wars Game PCB (at Settings of 1 2

On On

Off On Off Off

On Off

On Off

On Off On Off On On Off Off

On Off On Off On Off On Off On On Off Off On On Off Off 1OE/F)

On On On On Off Off Off Off Option

Free Play 2 Credits 1 Credit <4 % Credit *

Left Coin Mechanism 1 Coin 2 Coins

Right Coin Mechanism 1 Coin 4 Coins 5 Coins 6 Coins

Bonus Coin Adder 0 Bonus Coins Added<4 1 Bonus Coin Added for 2 Coins 1 Bonus Coin Added for 4 Coins 2 Bonus Coins Added for 4 Coins 1 Bonus Coin Added for 5 Coins 1 Bonus Coin Added for 3 Coins 0 Bonus Coins Added 0 Bonus Coins Added

4Manufacturer's recommended settings (US-built cabinet)

  • Manufacturer's recommended settings (Ireland-built cabinet)

Table 1-4 Switch Settings for Special Options

Settings of 4-Toggle Switch on Star Wars Game PCB (at 11L)

123Option
Onno}no}be]Outputs of coin counter driver 1 and 2 tied together
2Ss3
333(for 1 counter)4
Off333Outputs of coin counter driver 1 and 2 separate (for 2
zvAa

counters)*

4 Manufacturer's recommended settings (for US-built cabinet)

  • Manufacturer's recommended settings (for Ireland-built cabinet)

1-8

Page 17

STAR WARS COCKPIT

Game Play

STAR WARS is a One-player game with a color XY video display. You command LUKE SKYWALKER's RED 5-X-WING spacecraft with Atari’s new flight control. Your main goal is to blow up the DEATH STAR’. To do this, you must reach the thermal exhaust port at the end of the DEATH STAR trench, and fire a proton torpedo into it. You must survive three phases of play to reach the exhaust port. The first phase of play will engage you in a spectacular battle in space—a war in the stars! TWIN-ION ENGINE (T.LE.) FIGHTERS* from the DEATH STAR attack you. DARTH VADER’s Ship appears in this phase—menacing and powerful! Your goal in this phase is to shoot the T.L.E. FIGHTERS and their shots.

The second phase of play takes the XING down to the surface of the DEATH STAR which is covered with laser bunkers and laser towers. You must avoid collision with these objects and their shots to keep the number of Deflector Shields above zero. Extra bonus points are earned for exploding all laser tower tops. The third phase of play takes RED 5 down into the DEATH STAR trench. The walls are lined with red laser-gun turrets that fire at you as you approach. You must counter these shots by avoiding them or by shooting them. Trench catwalks also appear, in varied shapes and altitudes. You must avoid hitting the catwalks, or else your number of deflector shields will decrease. If you survive the flight down the trench, a message and voice will alert you that the exhaust port is straight ahead. You must shoot the exhaust port to explode the DEATH STAR. If you miss the exhaust port, you will plough through the wall at the end of the trench and lose one deflector shield. If you succeed in blowing up the DEATH STAR, RED 5 soars away from the DEATH STAR and then turns to view the tremendous explosion. Select-a-Death Star bonus and Remaining Shield Energy bonus are now scored. Depending on the settings of the option switches (see Tables 1-2, 1-3, and 1-4), additional deflector shields will be awarded. A new DEATH STAR then comes into view. The EMPIRE* is really mad now, and the powers in the EMPIRE want to launch LUKE and the RED 5 into eternity! STAR WARS has five possible modes of operation: Attract, Select-a-Death Star, Play, High Score, and Self-Test.

  • © 1983 Lucasfilm Lid. & Atari, Inc All rights reserved. Lucasfilm trademarks used under license. Set-Up

Attract Mode

The Attract Mode begins when power is applied to the game; or when the Play, High-Score, or Self-Test Modes end. The Attract Mode ends either when a credit is entered and the game goes into Select-a-Death Star Mode, or when the self-test switch is turned on.

The first screen displayed in the Attract Mode is the Banner Screen. The STAR WARS logo appears with a background of moving stars and then flies away to infinity. As it vanishes, the introductory story line moves into position from the bottom of the screen. The text pauses for about 20 seconds and then, one line at a time, quickly recedes into the distance.

Banner Screen Text: OBI-WAN KENOBI IS GONE BUT HIS. PRESENCE IS FELT WITHIN THE FORCE. THE EMPIRE'S DEATH STAR UNDER THE COMMAND OF DARTH VADER NEARS THE REBEL PLANET. YOU MUST JOIN THE REBELLION TO STOP THE EMPIRE. THE FORCE WILL BE WITH YOU. ALWAYS.

The next screen in the Attract Mode is the Flight Instruction Screen. It outlines RED 5's weaponry, defense system, and mission. The text appears one line at a time, pauses for about 20 seconds, then fades away. Flight Instruction Screen FLIGHT INSTRUCTIONS TO RED FIVE

  • YOUR X-WING IS EQUIPPED WITH AN INVISIBLE DEFLECTOR SHIELD THAT WILL PROTECT YOU FOR x** COLLISIONS.
  • DEFLECTOR STRENGTH IS LOST WHEN A FIREBALL IMPACTS YOUR SHIELD OR WHEN YOU STRIKE A LASER TOWER OR TRENCH CATWALK.
  • AIM YOUR LASERS WITH CURSOR TO EXPLODE EM- PIRE TIE FIGHTERS, LASER TOWER TOPS AND TRENCH TURRETS.
  • SHOOT FIREBALLS BEFORE THEY IMPACT YOUR SHIELD.
  • THE REBEL FORCE IS DEPENDING ON YOU TO STOP THE EMPIRE BY BLOWING UP THE DEATH STAR.

The top part of the Banner Screen should display the last score achieved and the wave number. The messages /N- SERT COINS) and X COINS PER PLAY should alternately flash if no credit is in the game. If the game has credits, then the message X CREDITS and PULL FIRE TRIGGER TO START will be displayed. These messages appear on all screens,

The third screen in the Attract Mode is the Scoring Screen. It lists targets in the game and their point values. This screen scrolls up from the bottom of the screen then fades away. ** Replace x with 6, 7, 8, or 9. depending on option switch settings.

Page 18

Set-Up

Scoring Screen SCORING TIE FIGHTERS 1,000 DARTH VADER SHIP. 2,000 LASER BUNKERS 200 LASER TOWERS 200 TRENCH TURRETS 100

FIREBALLS 33

EXHAUST PORT 25,000 DESTROYING ALL TOWER TOPS 50,000 The fourth screen in the Attract Mode is the High-Score Screen. It displays a table containing the ten highest scores. At the bottom of the screen the copyright message appears. (The High-Score Screen shown here contains the default entries that will appear if no high scores are in the game’s memory.) The game will retain and display the top three scores entered into its memory even if the power is turned off and then on again. STAR WARS COCKPIT

High-Score Screen

PRINCESS LEIA’S REBEL FORCE

LOBI1285353
2.WAN1110936
3.HAN1024650
4.GR872551
5.MLH813553
6.JED704899
7.NLA518006
8EJD492159
9.EAR384766
10.RLM380655

STAR WARS © 1983 LUCASFILM LTD. AND ATARI, INC. ALL RIGHTS RESERVED LUCASFILM TRADEMARKS USED UNDER LICENSE. You may bring the High-Score Screen or the Flight Instruction Screen into view at any time during the Attract Mode. Moving the flight control to the right displays the High- Score Screen and moving it to the left displays the Flight Intruction Screen.

Select-a-Death Star Mode

The Select-a-Death Star Mode begins when the correct credit(s) is entered and a fire trigger is pulled. You will hear the voice of LUKE saying, “RED 5 standing by,’ and you'll have 8 seconds to select one of 3 starting DEATH STARS. A DEATH STAR is selected by first maneuvering the flight control until the cursor on.the screen is positioned on the de- Sired DEATH STAR and then by pulling the Laser Fire Trigger. The DEATH STARS are labeled easy, medium, and hard on the display. The Easy DEATH STAR awards no bonus for completion of the starting level as indicated by NO BONUS. The Medium DEATH STAR awards 400,000 points and the Hard DEATH STAR awards 800,000 points. Failure to select a level within the countdown time automatically starts the Play Mode at the Easy level (wave one).

Page 19

STAR WARS COCKPIT

Play Mode

STAR WARS game play is enhanced by 13 special sound effects and by actual character voices communicating with the player. Voices: LUKE: RED 5 standing by. LUKE: R2, try and increase the power. LUKE; This is RED 5, I’m going in. LUKE: I'm hit but not bad, R2 see what you can do with it. LUKE I've lost R2. LUKE: I can’t shake him! DARTH I’m on the leader. DARTH The FORCE is strong with this one. DARTH: Thave you now! DARTH: Stay in attack formation. BEN: Use the FORCE, LUKE. BEN Remember, the FORCE will be with you, always. BEN: LUKE, trust me. BEN: Let go, LUKE. HAN: Yahoo! You're all clear, kid. HAN: Great shot kid! That was one ina million. WEDGE* Look at the size of that thing! R2: Yes. R2: No. R2: l agree. R2: Sequence completion. R2: Ouch! R2: That really hurt. The Play Mode begins in outer space with the DEATH STAR Off in the distance. The RED 5 XWING aiming device (cursor) appears as a crosshair on the screen. As the flight control is moved in any direction, the four laser guns move accordingly. Firing the laser guns will cause alternating, laser beams to fire from the guns toward the cursor. In this mode, R2-D2 is controlling the flight pattern of the x WING based on the flight of attacking T.1.E. FIGHTERS.

Your goal is to blast any and all T..E. FIGHTERS and their oncoming shots. If you are hit, your deflector shield will automatically turn on and dissipate the energy from the shot, causing a very bright light to flash on the screen. You will experience a roll in space due to the impact. Ina while, the TLE. FIGHTERS will turn away from you and fly back to the DEATH STAR.

*© 1983 Lucasfilm Ltd, & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. Set-Up

In the next phase of the Play Mode, the x.WING flies directly toward the DEATH STAR, engines roaring, to a surface covered with hostile laser bunkers and laser towers. Now you, not R2-b2, control the X-wiNG. Your goal in this phase is to reach the trench. To do this you must avoid or eliminate (by shooting) the structures and the shots fired by them. The laser tower tops have a progressive scoring incentive that is displayed in a message in the top center of the screen, along with the number of remaining laser tower tops to be destroyed before the x-wING dips into the trench. Eliminating all laser tower tops awards you an added bonus. Getting hit by a shot or smashing into a laser tower top or laser bunker will roll the x-wING to the right or left as the deflector shield automatically turns on and absorbs impact, displaying a very bright screen. Each collision costs you one deflector shield.

Once you have traveled the required distance over the DEATH STAR surface, the X-WING dips down into the long, deadly trench. In this phase, you can fly right, left, up, or down; but you remain within the trench. Your main goal while in the trench is to destroy the DEATH STAR by shooting the exhaust port at the end of the trench. You can survive the trench by flying around catwalks, which stretch across the trench at various altitudes, and by avoiding or shooting shots fired from the red laser-gun turrets on the walls. Deflector shield energy is lost if a shot hits you or if you smash into a catwalk. If you successfully reach and shoot the exhaust port, the RED 5 XWING will soar away from the DEATH STAR and then turn toward it to watch it blow up. If you miss the exhaust port, you will crash through the back wall and R2-D2 will show his displeasure with you. The X.wiNG will remain in the trench until the DEATH STAR is destroyed or you run out of deflector shields. Upon destroying the DEATH STAR, the X-WING returns to another war in the stars with smarter T.1.E. FIGHTERS from a more advanced DEATH STAR. Your ability as a JEDI WARRIOR’ will be challenged even more with the destruction of each successive DEATH STAR.

1-41

Page 20

Set-Up

Hints for Game Play © Develop skill for controlling the X-WING with the flight control. It’s like flying a plane. © Blast all the laser tower tops with your laser guns for additional bonus points. © STAR WARS is a pattern game, so learn the easy levels, and then select a more difficult level. © The game requires almost constant laser fire during higher levels. The game ends when you get hit and the deflector shield level is zero. The words GAME OVER appear in a very large size as your ship vanishes from the screen.

High-Score Mode

This mode begins with lively music if your score is one of the ten highest scores earned since the game was turned on. A screen appears with the message: MESSAGE FROM REBEL COMMAND POST

YOU ARE A TRUE REBEL PILOT

THE FORCE 1S WITH YOU SHOOT YOUR INITIALS Initials surround the high-score table in the middle of the screen. You have 30 seconds to shoot (enter) your initials. The top 3 scores will be saved even with the power off, but the entire high-score table can be reset to its default scores when in the Self-Test Mode. STAR WARS COCKPIT

Self-Test Mode

Self-Test is divided into two sections. The first section shows game statistics and allows the operator to reset certain statistics or change options with the use of the flight control. The second section is designed to allow checking of game switches, hardware failures, potentiometer adjustments, and video display adjustments. Self-Test may be entered any time during the Attract Mode. See Chapter 2 for details.

Page 21

Ps Self-Test

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

e Chapter 2

Page 22

SelfTest

Self-Test Displays

Fourteen self-test displays provide a visual check of the game statistics, options, switch settings, mathbox circuitry, display circuitry, and the condition of the read-only memory (ROM) and random-access memory (RAM). The first self-test display (Size and Centering) is obtained while in the Attract Mode. When the self-test switch is turned on during the Attract Mode, the game enters the Self-Test Mode. Turning the self-test switch off at any time during the Self-Test Mode causes the game to return to the Attract Mode.

NOTE Before selecting the Self‘Test Mode, perform the following size and centering check with the game in the Attract Mode. The remaining self-test displays are obtained while the game is in the Self-Test Mode.

Size and Centering Display While the game is in the Attract Mode, verify that a small blue dot is displayed within 4% -inch of the edge in each corner of the screen. If the blue dots are not in the proper position, refer to the X/Y size and centering adjustment procedures included on the Analog Vector-Generator schematic diagrams.

NOTE The following self-test displays are arranged in the sequence in which they occur after the selftest switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. If the self-test procedures are not performed in sequence, pressing the auxiliary coin switch will advance through the displays until the desired display is obtained. After the last display has ended, the sequence starts over with the Switch Test display. To start with the Accounting and Game Times display, the self-test switch must first be turned off and then on again.

Accounting and Game Times Display Select the Self-Test Mode by pushing the self-test switch to the up position. The Accounting and Game Times display will appear as shown in Figure 2-1. The totals on this display are those accumulated since the accounting and game times information was last reset. (Refer to Game Options Display for the reset procedure.) The coin accounting information, which is the first four statistics in the Accounting Information section of the display, cannot be reset. They are accumulated from the date the game was manufactured, or since the non-volatile random-access memory (NOVRAM) last failed or was replaced.

2-2 STAR WARS COCKPIT

@Ux COIN TO CONTINUE

Figure 2-1 Accounting and Game Times Display AUXILIARY COINS displays the number of free credits selected by the auxiliary coin switch in the normal play mode. LEFT MECH COINS displays the number of coins inserted into the left coin mechanism. RIGHT MECH COINS displays the number of coins inserted into the right coin mechanism. TOTAL COINS PAID displays the total number of coins inserted into both game coin mechanisms.

NOTE The following accounting and time information is accumulated since the game was manufactured (or last reset). Refer to Game Options Display for the reset procedure.

GAMES PLAYED displays the total number of free and paid games played and highest wave achieved. TOTAL GAME TIME displays the total time, in seconds, ofall the games played. AVERAGE GAME TIME displays the average time, in minutes and seconds, of all the games played. TOTAL TIME ON displays the total time, in seconds, the game has been on. PERCENTAGE OF PLAY displays the percentage of time the game has been in Play Mode (as opposed to Attract Mode). HISTORY OF GAME TIMES displays the number of games played that were within each of 18 game-time increments (0 to six minutes in 20- second increments). @

Page 23

STAR WARS COCKPIT

Game Options Display Press the auxiliary coin switch to obtain the Game Options display as shown in Figure 2-2. Use this display to view or change game option settings; reset high scores; reset accounting and game time information; or test the NOVRAM.

Figure 2-2 Game Options Display The first section of the Game Options display shows the option settings that have been selected by either the option switches on the Main printed-circuit board (PCB) or by the flight control. The second section of the Game Options display shows the reset and NOVRAM test operations that are selectable with the flight control. Press the auxiliary coin switch to end this display. Changing the Game Options. Any of the options displayed in the first section of the Game Options display can be changed without setting the option switches on the Main PCB, Select the option to be changed by moving the flight control up or down. Press the left-hand fire trigger to cycle through the available options as indicated in the right-hand column; stop on the desired option setting. The changed option is immediately stored in the NOVRAM and is unaffected by turning off the power or the self-test switch. The options can also be changed to those selected by the option switches located on the Main PCB (see Chapter 1). If the self-test circuitry malfunctions or the option settings cannot be maintained by the software, the game will default to the hardware switch settings on the Main PCB (refer to Resetting the Options for more details). Resetting the High Scores. The top ten scores and player initials are displayed in the high-score table during the Attract Mode. All high scores can be reset using the Game Options display. Select RESET HIGH SCORES by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Self-Test

Resetting the Timing Information. The games played and the timing information in the Accounting and Game Times display (see Figure 2-1) can be reset using the Game Options display. Select RESET TIMING INFO by moving the flight control up or down. Press the left-hand fire trigger and

note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Resetting the Options. The option settings shown on the Game Options display (see Figure 2-1) can be reset (defaulted) to those selected by the option switches located on the Main PCB. Select RESET OPTIONS by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Testing the NOVRAM. The NOVRAM can be tested using the Game Options display. Select TEST NOVRAM by moving the flight control up or down. Press the left-hand trigger and check that NO ERRORS appears in the right-hand column. If the NOVRAM is defective, a message ERROR AT and a hexadecimal number will appear, which indicates that the NOVRAM should be replaced. Testing the NOVRAM should only be performed if a defective part is suspected because each test decreases the life of the NOVRAM.

2-3

Page 24

Self-Test

Hardware Errors Display Press the auxiliary coin switch and wait about seven seconds to obtain the Hardware Errors display as shown in Figure 2-3. This display shows the condition of the game RAM and ROM. If no hardware errors exist, the message NO ERRORS DETECTED will be displayed. If there is a RAM or ROM failure, the display will identify the failed component and give its location (see Figure 2-4).

NO ERRORS DETECTED

PRESS 9@ux EDIN TO CONTINUE

Figure 2-3, Hardware Errors Display—Test Passes

PROGRAM PROGRAM PRogRAM

Figure 2-4 Hardware Errors Display—Test Fails

Switch Test Display Press the auxiliary coin switch to obtain the Switch Test display as shown in Figure 2-5. Perform the following procedure to verify that the game switches are operating properly.

2-4 6. STAR WARS COCKPIT

One ata time, press the fire triggers and thumb pushbuttons. Note that a message appears on the display that indicates which switch was pressed. Actuate the right and left coin mechanisms and note that a message appears that indicates which coin mechanism was actuated. Position the flight control to form a single dot in the center of the smallest box in the POT TEST portion of the display. Carefully release the flight control and note that the dot remains centered within the smallest box. Ifa line forms that extends outside the frame of the smallest box, the flight control potentiometers may be misaligned. Refer to the flight control reassembly procedures in Chapter 4 for potentiometer alignment information. Tilt the flight control handles forward and backward;

note that a line forms from the center of the smallest box and moves out and back in relation to the handle position. Tilt the handles to the extreme forward and backward position; note that the line extends past the frame of the box with open corners but not beyond the frame of the largest box. Turn the flight control fully clockwise and counterclockwise with the handles at the extreme forward then backward positions. Note that the line travels over a full 360° while not extending outside the area between the largest box and the box with the open corners. Verify that the option settings for the switches at location 10D and 10E/F shown at the bottom center of the display match those selected on the corresponding option switches (F = off, N=on).

Figure 2-5 Switch Test Display @ <

Page 25

STAR WARS COCKPIT

Mathbox Tests Display

Press the auxiliary coin switch to obtain the Mathbox Tests display as shown in Figures 2-6 and 2-7. The first test verifies that the MATHBOX READY signal is operating normally. If it is not, the message BAD MATHBOX READY LINE appears and no further mathbox tests are performed. If the MATHBOX READY signal is correct, then the divider and matrix circuitry should be tested. If no problems exist in the divider or matrix circuitry, the messages NO DIVIDER ERRORS and NO MATRIX ERRORS are displayed. If divider errors exist, the message DIVIDER ERRORS will appear and each error will be indicated with an optionswitch setting for the corresponding diagnostic. Also, the numbers used on the test with the expected answer and the incorrect answer received will be displayed for each test in error.

Figure 2-6 Mathbox Tests Display—Test Passes

Bap MATHBDX READY LINE

Figure 2-7 Mathbox Tests Display—Test Fails Self-Test

If matrix errors exist, the message MATRIX ERRORS will appear with the corresponding option switch settings for the diagnostic. Some matrix errors do not have a corresponding diagnostic. In this case, there will be no option switch setting.

Crosshatch Pattern Display Press the auxiliary coin switch to obtain the Crosshatch Pattern display as shown in Figure 2-8. Verify the following display characteristics:

  • Corners are closed and the diagonal lines form symmetrical diamond-shaped squares. ¢ All four corners of the border are completely visible and are within 4 -inch from the black edge of the screen. © Pattern is not tilted more than %4-inch between corners. ¢ Pattern is a uniform green color.

Figure 2-8 Crosshatch Pattern Display

If any of the preceding characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector- Generator schematic diagrams.

Page 26

Self‘Test

Grid Pattern Display Press the auxiliary coin switch to obtain a Grid Pattern display as shown in Figure 2-9. Verify that the following grid colors can be obtained, in order, by pressing either fire trigger: Red Green Blue Purple White Yellow Turquoise

Figure 2-9 Grid Pattern Display

Verify the following display characteristics: © Grid lines do not exhibit pincushioning or barreling and the lines are straight within 44-inch.

  • Convergence shall not exceed 2.0 mm, as checked with the white grid. Ifany of the preceding display characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector-Generator schematic diagrams and to the convergence adjustment procedure in the Display Manual. STAR WARS COCKPIT

Intensity Test Display Press the auxiliary coin switch to obtain the Intensity Test display as shown in Figure 2-10. Verify the following display characteristics: © = Top row of color bars are red, blue, and green. © Allthree sets of color bars have six lines with the same intensity. © Bars underneath the top row of color bars are white. © Bars underneath the white color are yellow, turquoise, and purple. © DIM, LOW, and HIGH appear in the bottom center of the display. If the word OFF can be seen, the display is too bright. If the word LOW cannot be seen, the display is not bright enough.

INTENSITY TEST

Figure 2-10 Intensity Test Display

If the preceding display characteristics are not correct, refer to the Display Manual for the brightness adjustment procedure or to determine the possible cause of failure.

@ <

Page 27

STAR WARS COCKPIT

Bipolar Offset Test Display Press the auxiliary coin switch to obtain the Bipolar Offset Test TEST display as shown in Figures 2-11 and 2-12. The line width should be %-inch or less. If not, adjust the X/Y bipolar offset potentiometers located in the digital-toanalog converter and bipolar current sources circuit on the Analog Vector-Generator PCB.

Figure 2-11 Bipolar Offset Test Display-Test Passes

Figure 2-12 Bipolar Offset Test Display—Test Fails Self-Test

Scale Test Display Press the auxiliary coin switch to obtain the Scale Test Linear display as shown in Figure 2-13. A large green square should appear in the center of the screen and then smoothly shrink to a point. Next, a large green SCALE TEST LINEAR AND BINARY squate appears and shrinks smoothly, then pauses and continues to shrink. There should be eight pauses before the square shrinks toa point. After each pause and just when the square begins to shrink, the size of the square should not change appreciably. Ifa large change in the size of the square occurs, an error may exist. After the eighth pause, the sequence repeats with the Scale Test Linear and Binary display as shown in Figure 2-14.

SCALE TEST LINEAR

Figure 2-13 Scale Test Linear Display

SCALE TEST LINEAR AND BINARY

Figure 2-14 Scale Test Linear and Binary Display

Page 28

Self-Test Star Wars

Raster Screen Display

Press the auxiliary coin switch to obtain the Raster Screen e@ 4q

display as shown in Figure 2-15. This display is the last of the self-test displays and is used by the manufacturer to adjust the white tracking of the display circuitry.

Figure 2-15 Raster Screen Display

NOTE Pressing the auxiliary coin switch to end the preceding Raster Screen display will repeat the self-test sequence starting with the Switch Test display. If desired, turn the self-test switch off, then on again, to obtain the Accounting and Game Times display.

2-8

Page 29

Troubleshooting

This chapter contains a discussion of troubleshooting aids and techniques to assist the service technician when a trouble is suspected in this game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your nearest Atari Customer Service office listed on the inside front cover of this manual for assistance. Athorough knowledge of game operation is desirable for effective troubleshooting. In addition to the operation and service information in the Schematic Package Supplement included with this manual, refer to The Book, A Guide To Electronic Game Operation and Servicing, available from Atari, Inc., for more information on coin-operated electronic games.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified electronic technician.

Chapter 3

Page 30

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the Schematic Package Supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The illustrated parts lists in Chapter 5 illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components contained on the corresponding schematic diagram(s).

Schematic Diagrams

Complete schematic diagrams are provided in the Schematic Package Supplement. Component designations and their electrical values are included on the schematic diagrams. A memory map and a key to the schematic reference designators and symbols are also included in the Schematic Package Supplement. A block diagram of the major circuits on the game PCB (with sheet numbers to aid in locating the appropriate schematic diagrams) is included in the Schematic Package Supplement.

Troubleshooting Procedures

This game will test itself and provide data to aid in localizing troubles to a major circuit. Self-test procedures are provided in Chapter 2. Refer to the following section on Troubleshooting Techniques for a suggested troubleshooting sequence that uses the self-test procedures. Detailed troubleshooting procedures for locating defective components are provided in the Schematic Package Supplement. These procedures use the Atari CAT Box to troubleshoot the game PCB.

Troubleshooting Techniques

The following troubleshooting steps are arranged ina sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the trouble to an assembly or major circuit, and then to a defective component.

Check Switch Settings Incorrect switch settings can sometimes indicate a problem that does not exist. Refer to Chapter 1 Set-Up, to verify that the game has been installed properly and that the switches are set to their correct positions. Check for proper operation in all game-play modes.

3-2 STAR WARS COCKPIT

Check Fuses Check for open fuses. Refer to the Power Supply Assembly Parts List in Chapter 5, Illustrated Parts Lists, and to the Display Manual, for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages Improper operation of all circuits usually indicates a power supply problem. Check that the proper line voltage is available to the power supply.

Localize Trouble Determine the trouble symptom. Use the wiring diagrams in the Schematic Package Supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2.

Visual Check Visually check for obvious problems in the portion of the game where a trouble is suspected. For example, check for loose or defective solder connections, integrated Circuits loose in their sockets, loose cable connections, broken wires, damaged printed-circuit boards or components.

Check Individual Components

Toavoid electrical shock, turn the game off before removing or replacing components.

CAUTION Transistors and integrated circuits soldered in place are difficult to remove without damaging the printed circuit board or component. Be extremely careful when removing these components,

Check soldered-in components by disconnecting one end to isolate the measurement from the affects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if acomponent is faulty. However, eliminate the possibility of some other circuit problem existing which could damage the substitute component.

Repair the Assembly Repair or replace the defective part. Refer to Chapter 4, Maintenance and Repair for special repair and replacement procedures. Check for proper operation of any repaired circuit.

Page 31

e Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use, To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

@ Chapter 4

Page 32

Maintenance STAR WARS COCKPIT

Cleaning Requirements r (

This game cabinet and display shield may be cleaned with any non-abrasive household cleaner. The coin mechanism should be cleaned periodically with hot or boiling water and a mild detergent. A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, flush thoroughly with hot or boiling water and blow out all of the water with compressed air. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

  • Unlock and remove the rear access panel.
  • Reach up through the rear of the cabinet to the top of the control panel to remove the two nuts and washers that secure the control panel using a %-inch combination wrench.
  • Lift the control panel at the top edge and tilt it toward you.

@

Page 33

STAR WARS COCKPIT

Flight Control Maintenance

Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. The flight control consists of a handle assembly and a steering assembly. The handle assembly controls the vertical motion, and the steering assembly controls the horizontal motion of the display. Routine maintenance can be performed without removing the flight-control assembly from the game. After any corrective maintenance is performed, the flight control should be recalibrated as described in Chapter 1. Refer to Figures 4-1 and 4-2 for the locations of the parts mentioned in the following procedures. Routine Maintenance Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. Lubrication. Perform periodic lubrication of the flight control assembly as follows (see Figures 4-1 and 4-2): 1, Open the control panel as previously described in this chapter.

NOTE The handle-assembly covers are attached with tamper-proof socket screws. A special 43-inch hex-key tool is supplied with each game (Atari part no. 178126-001).
  • Use the special 42-inch hex-key tool to remove the four tamper-proof socket screws from the handle assembly cover.
  • Lift off the handle assembly cover and lubricate the following parts inside the flight control: (Refer to Figures 4-1 and 4-2 for an illustration of the lubrication points.)
  • Apply two drops of light machine oil lubricant (Atari part no. 107013-001) to the insides of the four shaft bearings. ¢ Brush a light film of Nyogel 779 lubricant (Atari part no. 178027-001) on the teeth of the two small spur gears,
  • Apply a small amount of WD-40 or a light machine oil to the potentiometer shafts as needed for squeaking. Screw and Nut Tightness. Use the appropriate hex-head and combination wrenches to check the hex-head cap screws and mounting nuts for tightness. Refer to Figures 4-1 and 4-2 for an illustration of the cap screw and mounting nut locations. Maintenance

Removing the Handles Perform the following procedure to remove the handles from the handle assembly (see Figure 4-1):

NOTE The handles on the handle assembly are assembled with tamper-proof cap screws. A special 42-inch hex-key tool is supplied with each game (Atari part no. 178126-001) to remove the tamper-proof cap screws.
  • Use the special 42-inch hex-key tool to remove the four tamper-proof cap screws that hold the covers on the handles. Be careful when removing the covers because the trigger and pushbutton springs can fall free from the handles.
  • Unsolder the three harness wires from the trigger and pushbutton microswitches inside each handle.
  • Use the special %-inch hex-key tool to remove the four tamper-proof cap screws that hold the handles to the shaft.
  • Gently slide the handles from the shaft.
  • Reassemble in reverse order.

Removing the Flight Control

NOTE Certain corrective maintenance procedures can be performed with the flight control attached to the control panel. However, for convenience and to avoid damaging the control panel, we recommend that the flight control be removed from the control panel before any maintenance is performed.

Perform the following procedure to remove the flight control from the control panel:

  • Open the control panel as previously described.
  • Unplug the flight-control harness assembly.
  • Usea %.-inch combination wrench to remove the four locknuts and washers that mount the flight control to the control panel.
  • Carefully guide the flight control through the hole in the control panel.
Page 34

Maintenance

Disassembling the Handle Assembly Perform the following procedure to disassemble the handle assembly (see Figure 4-1):

NOTE Removing the handle assembly from the steering assembly is not necessary to perform the procedure below. However, if you wish to do so, refer to Disassembling the Steering Assembly in this chapter for the procedure that describes how to separate the two assemblies.
  • Use the special 42-inch hex-key tool to remove the four tamper-proof cap screws from the handleassembly covers.
  • Remove the handles as previously described.
  • Gently pull the harness wires out of the hollow shaft. 4, Use a %4-inch hex driver to remove the cap screw and washer that hold the spring pin to the handleassembly shaft.
  • Slide the spring pin out of the shaft.
  • Usea %,-inch hex driver to loosen the cap screw that holds the large (60 tooth) spur gear to the shaft.
  • Slide the large (60 tooth) spur gear down the shaft to expose the shaft retainer on the right side.
WARNING Shield your face and eyes when prying out the retainers because they can fly loose at a high velocity. Cover the retainers with a rag or any material that will trap the retainer.
  • Use aright-angle slotted screwdriver, or equivalent, to pry the retainer from the shaft.
  • Repeat steps 7 and 8 to remove the retainer on the opposite side.
  • Gently slide the shaft from the housing. Be careful not to lose the torsion springs. ll. Use a %,4-inch hex driver to loosen the cap screw that holds the small (14 tooth) spur gear to the potentiometer shaft. 12, Usea %-inch combination wrench to remove the nut and washer that hold the potentiometer to the mounting bracket.
  • Slide the potentiometer from the bracket. Be careful not to lose the small spur gear, nut, and washer. 14, Use a 42-inch hex-head wrench and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the handle assembly as described in the following procedure.

4-4 STAR WARS COCKPIT

Reassembling the Handle Assembly Follow the steps below to reassemble the handle assembly (see Figure 4-1):

  • Use a %2-inch hex driver and %-inch combination wrench to install the two bumpers on the frame.
  • Insert the large (60 tooth) spur gear with the collar facing away from the bearing. Hold the gear inline with the bearing hole. (The gear fits through the slot on the right front of the frame.)
  • Slide the shaft through the right-hand bearing and the spur gear, Do not insert the shaft past the outside edge of the spur-gear collar.
  • Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the springs.
  • Hook the straight end of the first torsion spring through the hole closest to the right side of the frame.
  • Hold the first torsion spring in line with the shaft so that the looped end of the spring is facing away from the spur gear. Slide the shaft just through the first torsion spring. Hook the straight end of the second torsion spring through the hole closest to the left-hand bearing.
  • Hold the second torsion spring in line with the shaft so that the looped end of the spring is facing the first torsion spring.
  • Slide the shaft through the second torsion spring and the left-hand bearing. ll. Position the shaft so'that the retainer grooves are just inside the bearings.
  • Install the two retainers in the shaft grooves.
  • Turn the shaft so that the two large holes and the smaller centered hole are facing upward.
  • Locate the hole in the spring-handle pin. Insert the end of the spring handle pin that is closest to the hole through the slot in the frame and through the hole in the shaft. Make sure that both torsion spring looped ends are wrapped over the spring handle pin.
  • Position the spring-handle pin so that the hole in the pin is aligned with the hole in the shaft.
  • Usea %4-inch hex driver to tighten the cap screw and washer that secure the pin to the shaft.
  • Align the cap screw in the spur-gear collar with the threaded hole in the shaft, and use a %,-inch hex driver to tighten the cap screw.
  • Insert the potentiometer shaft through the hole in the mounting bracket. Place the washer, nut, and small (14 tooth) spur gear (with the collar facing inward) onto the shaft before fully inserting the shaft through the bracket.
Page 35

STAR WARS COCKPIT Maintenance

] r 19, Align the potentiometer so that the tab key is inserted 24. Use a %-inch combination wrench to tighten the into the keying slot. potentiometer to the mounting bracket.

  • Usea %-inch combination wrench to slightly tighten 25. Perform the procedure for installing the harness the nut on the potentiometer shaft. assembly provided at the end of this chapter.
  • Turn the potentiometer shaft so that the flat side faces 26. Install the handles in the reverse order of the removal the center wire terminal. procedure previously described. Do not install the
  • Align the cap screw on the small (14 tooth) spur gear handle covers until the harness is installed and the . with the flat side of the shaft. Use a %,-inch hex driver proper wires are soldered to the trigger and pushbutto tighten the cap screw. ton microswitches.
  • Slide the potentiometer forward so that the teeth on 27. Install the handle assembly cover and use the special . the two spur gears are tightly meshed; then pull the a-inch hex-key tool to tighten the four tamper-proof potentiometer and small (14 tooth) spur gear away socket screws that secure the cover to the handle from the large spur gear about %,-inch. assembly.

Wire & Cable Tie

Potentiometer

White Red Black Tab Key

Harness Assembly

Handle Assembly ~~ Collar -

‘Bumper

‘Keying Slot

‘Small Spur Gear Trigger Microswitch

Sleeve (R) Spring Pin First Torsion Spring Spur Gear Red (Normally Open)

Cap Screw

Handle —— Cover

Figure 4-1 Handle Assembly

Page 36

Disassembling the Steering Assembly Perform the following procedure to disassemble the steering assembly (see Figure 4-2):

  • Remove the handle covers as described earlier in this chapter. Remember, be careful when opening the handles because the pushbutton and trigger springs may fall out.
  • Unsolder the three harness wires from the vertical potentiometer, handle pushbutton microswitch, and trigger microswitch.
  • Usea %,-inch hex driver (or ball-end driver) to remove the three cap screws that hold the steering-assembly shaft to the handle-assembly frame. 4, Gently pull the two assemblies apart. Make sure the harness wires are free to slide out of the handleassembly shaft.
  • Usea ¥.-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut faces the open end of the frame.)
  • Slide the anchor pin out of the shaft.
  • Grasp the large (60 tooth) spur-gear and slide the shaft from the frame. The bearing spacer, torsion springs, and large flat washer will fall free.
  • Use a %,-inch hex driver to remove the cap screw holding the large spur gear to the steering shaft anda %q-inch hex driver to remove the set screw that holds the small spur gear to the potentiometer shaft.
  • Usea %-inch combination wrench to remove the nut and washer that hold the potentiometer to the frame.
  • Unsolder the three harness wires from the potentiometer terminals.

Shield your face and eyes when prying the retainer from the shaft since the retainer can fly loose at a high velocity. Cover the retainer with a rag or any material that will trap the retainer.

  • Usea slotted screwdriver, or equivalent, to remove the retainer from the shaft.
  • Use a %2-inch hex driver and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the steering assembly as described in the following procedure.

Reassembling the Steering Assembly Perform the following procedure to reassemble the steering assembly (see Figure 4-2):

  • Use a %2-inch hex driver and %-inch combination wrench to install the two bumpers to the frame.

4-6 14.

15. STAR WARS COCKPIT

Snap the retainer into the groove in the shaft and slide the large flat washer down the long end of the shaft and against the retainer. Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the springs. Hook the straight end of the first torsion spring through the hole closest to the rear of the frame. Slide the shaft through the outside bearing and the first torsion spring. Hook the second torsion spring through the hole on the opposite side and closest to the front of the frame. Slide the shaft through the second spring and the opposite bearing. Turn the shaft so that the threaded hole at the retainer end of the shaft faces up toward the open side of the frame. The hole through the center of the shaft will then be perpendicular to the open side of the frame. Use a 45-inch combination wrench to install the anchor pin and nut through the hole in the center of the shaft. Make sure the torsion spring looped ends are wrapped under the anchor pin and nut. Slide the large (60 tooth) spur gear onto the shaft with the collar facing out. Align the cap screw in the spur-gear collar with the threaded hole in the shaft and use a %4-inch hex driver to tighten the cap screw. . Insert the potentiometer shaft through the hole in the frame and align the potentiometer so that the tab key is inserted into the keying slot. . Install the washer and nut on the potentiometer shaft but do not tighten. . Turn the potentiometer shaft so that the flat side faces the center wire terminal. . Align the cap screw on the small (28 tooth) spur gear with the flat side of the shaft and slide the small spur gear (with the collar facing inward) onto the potentiometer shaft. Position the spur gear so that its teeth mesh with those of the large spur gear and use a %,-inch hex driver to tighten the set screw. Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the potentiometer and small spur gear away from the large spur gear about %,-inch. . Use a %-inch combination wrench to tighten the potentiometer to the frame. Slide the bearing spacer over the shaft at the end op- Posite the spur gears. . If necessary, lubricate the steering assembly as previously described.

Page 37

STAR WARS COCKPIT

NOTE The remaining steps describe the procedure for attaching the steering assembly to the handle assembly.
  • Insert the steering-assembly shaft into the collar on the handle-assembly frame.
  • Align the three holes in the steering-assembly shaft with the three holes in the handle-assembly collar.
  • Usea %,4-inch hex driver (or ball-end driver) to tighten the three cap screws.
  • Install the harness assembly as described in the following procedure.

First Torsion Spring

Second Torsion Spring

Anchor Pin

Bumper Bearing Spacer Outside Bearing | Maintenance

Installing the Harness Assembly Perform the following steps to install the harness assembly into the flight control (see Figures 4-1 and 4-2):

  • Remove the handle covers as described under Removing the Handles.
  • Guide the harness wires into the spur-gear end of the hollow steering-assembly shaft.
  • Route and solder the wires to the potentiometers and microswitches. Note that the wire bundle that goes to the right handle is identified with a labeled sleeve (R).
  • Install the wire ties and the ground clip.

‘Small Spur Gear

Large Flat Washer

Green

Keying Slot

Ground Clip

Anchor Nut

Figure 4-2 Steering Assembly

4-7

Page 38

Maintenance

1-Pin DAG Spring Connector

Anode Cap and Lead’

CRT Neck-Pin Connector: STAR WARS COCKPIT

__— Connector

Degaussing Coil Connector

‘Upper Back Panel

‘Rear Door Panel

Figure 4-3 Removing the CRT Assembly

Removing the CRT Assembly

The cathode-ray tube assembly (CRT) may implode if struck or dropped. Shattered glass can cause personal injury within a 6-foot radius. To reduce the risk of injury to persons or damage to the game components, we recommend that two people perform the following removal procedures,

NOTE Readjust the brightness, purity, and convergence adjustments as described in the display manual whenever the cathode-ray tube is replaced. Use a Phillips-head screwdriver to remove the rear door panel and the upper back panel from the cabinet. Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attach one end of alarge, well insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. c. Wait two minutes and repeat step b.
Page 39

STAR WARS COCKPIT

  • Disconnect the CRT neck-pin connector, anode lead, yoke connector (J105 on the Deflection PCB), degaussing coil connector (J104 on the Deflection PCB), and the 1-pin DAG spring connector.

Be extremely careful when removing the CRT mounting nuts since the cathode-ray tube assembly can fall. We recommend that a second person carefully hold the CRT neck while the mounting nuts are being removed.

  • Usea %-inch combination wrench to remove the four nuts and washers from the underside of the display mounting bracket.

White/Red = Brown Red Maintenance

  • Very carefully remove the CRT assembly from the back of the cabinet.
  • Replace in reverse order.
NOTE Readjust the brightness, purity, and converence as described in the Display Manual whenever the CRT is replaced.

Wiring the Utility Panel

Controls

Refer to Figure 4-4 for the proper wire connections when replacing the controls that are mounted on the utility panel.

WARNING

Before removing or repairing the utilty panel, tum the game off. Players may receive an electrical shock ifthe utility panel is not properly grounded! After servicing any parts onthe panel, make sure that the ground wireis firmly attached to the bracket. White/Yellow

Orange

Yellow

Orange/Blue = First Coin Counter Orange/White/Violet Second Coin Counter

Black’ (Common)

Black Gray (Normally Open)

NOTE White Only the Iretand-built cabinet has two coin counters.

Figure 4-4 Utility Panel Wire Colors

Page 40

»e Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers,

  • etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. : The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99; then 000598through approximately 201000: When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

»@ Chapter 5

Page 41

Illustrated Parts Lists STAR WARS COCKPIT

A040518-01 Control Panel Assy. e @ A040519-01 Control Panel & Decal Assy.

040521-01 Canopy decals Control Panel See Figure 5-2 040520-03 040458-01 Decal Video Display Shield 040526-01 . Video Display Bezel

A200011-01 040463-01 25-inch Color XY , Front Window Display Assy. g . A201112-01 Cathode-Ray Tube Assy.

040454-01 Attraction Panel Retainer

Flight Control See Figure 5-3

Housing and Decal Assy. - ES xy See Figure 5-2 for Decals —

040455-01 Attraction Panel Retainer

Coin Door See Figures 5-6 or 5-7 040460-01 Attraction Glass

040439-01 Floor Cover

Adjustable Glide

Figure 5-1 Cabinet-Mounted Assemblies US-Built A040415-01 B @ « Ireland-Built A040415-10 B

5-2

Page 42

STAR WARS COCKPIT Mlustrated Parts Lists

Printed-Circult Board

See Figure 5-9

The enclosure contains the: Sound PCB 1 Regulator/Audio i! PCB Analog Veosor-Generator See Figures 5-9 & 5-1 040529-01 040528-01 . PCB Window Retainer Top Window See Figure $-13 Main PCB Lares See Figure 5-12 037332-01 Window Retainer a EMI Shield PCB Ventilation Grille See Figure 5-10

039144-01 Speaker Grille

A040416-01 A038881-01 ‘Cabinet Assy.

040448-01 Corner Cap

4 Utillty Panel Assy. ' \ See Figure 5-5

A040451-01 Speaker Panel Assy. See Figure 5-4 A040478-01 ‘Speaker Harness Assy. 009992-01 <i (not shown) On/Ott Switch Cover 039144-01 A040475-01 Main Harness

Speaker Grille 040449-01 ‘A037470-01 Coin Box Enclosure Speaker Panel Power On/Off Switch 148001-013 Speaker

:

A040547-01 Fan and Bracket Assy. A201012-01 A201014-01 : : 040546-01 aostassor PERE Supply Asay. Deflection PCB Assy. High-Voltage PCB Assy. Bracket ioure: Power Cord 040376-01 040376-02 171002-001 ‘A037784-03 Static Shield Static Shield Fan Power Cord 178093-001 : Blade Guard

Figure 5-1 Cabinet-Mounted Assemblies, continued > @ US-Built Cabinet A040344-01 A Ireland-Built Cabinet A040344-10 A

Page 43

Illustrated Parts Lists STAR WARS COCKPIT

Cabinet-Mounted Assemblies Parts List ee Part No. Description

A037453-01Power Cord(U.S. and Canada)

A037470-01 Power On/Off Switch and Mounting Plate Assembly

A037784-03Power Cord(England and Ireland)

A038881-01 Lock Assembly (for rear access panel—acceptable substitute is part no. A038881-03)

A040416-01Cabinet Assembly(includes glides, casters, and PCB retainers, but not the rear access panel)‘

A040451-01 Seat Speaker-Panel Assembly—includes: A040478-01 Speaker Harness Assembly 039144-01 Speaker Grille ' 040448-01 Corner Cap 040449-01 Seat Speaker Panel 148001-013, 6 x 9-Inch Oval, 4 9, 6 Ounce Magnet Shielded Speaker A040475-01 Main Harness Assembly A040476-01 Power Harness Assembly A040518-01 Control Panel Assembly—includes: A040233-01 Flight Control A040519-01 Control Panel and Decal Assembly—includes: 040521-01 Control Panel 040520-03 Decal for Control Panel A040531-01 Housing and Decal Assembly A040547-01 Fan and Bracket Assembly—includes: 040546-01 Fan Bracket 171002-001 Fan 178093-001 Fan Blade Guard e¢

A200011-0125-Inch Atari Color XY Display Kit Assembly—includes:'

‘A201112-01 Cathode-Ray Tube Assembly A201014-01 Deflection PCB Assembly A201012-01 High-Voltage PCB Assembly The following four items are technical information supplements to this game. SP-225 Star Wars Schematic Package ST-225 Star Wars Label with Self-Test Procedure and Option Switch Settings TM-239 25-Inch Atari Color XY Display Manual T™M-245 Star Wars Operators Manual with Illustrated Parts Lists 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick (not shown—apply 24 inches to each attraction panel retainer) 009992-01 On/Off Switch Cover 03453602 Foam Pad—%-Inch Thick (not shown—used as a vibration damper for PCB)

037243-01Base Plate for Power Supply(not shown),

037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown)

038870-01Coin Box Enclosure\

039144-01 Speaker Grille

040376-01Static Shield(not shown—located under the High-Voltage PCB)
040376-02Static Shield(not shown—located under the Deflection PCB)

040439-01 Floor Cover

(continued on next page) Y ) q

Page 44

STAR WARS COCKPIT IHustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, continued

Part No. Description

040443-02 Rear Access Panel (does not include lock) 040454-01 Lower Attraction Panel Retainer 040455-01 Upper Attraction Panel Retainer 040456-01 Window Retainer 040458-01 Video Display Shield 040460-01 Attraction Glass with Graphics 040463-01 Front Window 040526-01 Video Display Bezel 040528-01 Top Window 040529-01 Window Retainer 148001-017 6x 9-Inch Oval, 8 2, 6 Ounce Magnet Shielded Speaker 178023-001 4-Inch Diameter Rigid Caster 178034-024 %-Inch Black Plastic TMolding 178126-001 Hex Key Tool (not shown—shipped in the bag containing technical documentation—used for the tamperproof screws on the flight control)

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 46

STAR WARS COCKPIT

040382-05 Display Housing Decal—Center

i

040532-06 Display Housing Decal—Right

040520-03 Control Panel Decal

Figure 5-2 STAR WARS Cockpit Decals Mlustrated Parts Lists

040527-03 Canopy Decals

¥ Part No. Description

040381-04 Flight Control Decal 040382-05 Center Display Housing Decal 040520-03 Control Panel Decal 040527-03 Canopy Decals (set of 6) 040532-04 Left Display Housing Decal 040532-06 Right Display Housing Decal

5-7

Page 47

Illustrated Parts Lists STAR WARS COCKPIT

A040251-01 Steering Cover & Decal As

040093-02040091-0172-8812
Left Handle CoverLeft HandleCap Screw

‘ S gs 040303-01 176026-3610 ' fas \ Fee OK 040252-01 meaner O88" Gan Sew } : 4 GP Compression Spring} “Screw osnos2-01 040244-01 E> AM + Right Handle Cover Spring Pin / \ ; /

040247-01Handle Spring|‘4

Handle Assy. Frame |— Handle Shaft % i, ee

040235-01 en o4oost-02 Right Handle 176022-3604 Cap Screw

Figure 5-3 Flight Control Assembly A040233-01 A

5-8

Page 48

Illustrated Parts Lists

178012-001 Retaining Ring

040234-01 177010-241 Steering Shaft Nut

Flat Washer STAR WARS COCKPIT

A040236-01 : YP" 8G 040237-01 Steering Assy. Frame

Potentiometer

Spacer Bearing

See Chapter 4 for lubrication information.

Figure 5-3 Flight Control Assembly, continued A040233-01 A

5-9

Page 49

Illustrated Parts Lists STAR WARS COCKPIT

Flight Control Assembly Parts List

Part No. Description

A040236-01 Steering Assembly Frame—includes: 040243-01 Modified Bearing 040555-01 Steering Frame Weldment 72-L25510 #%-20 x Inch Long Self-Clinching Stud 04024701 Handle Assembly Frame—includes: 040243-01 Modified Bearing 040556-01 Frame Handle Weldment A040251-01 Steering Cover and Decal Assembly— includes: 040248-01 Cover 040382-07 Decal A040468-01 Flight Control Harness Assembly 19-9626 5 kQ Potentiometer 72-1206F #2-56 X %-Inch Cross-Recessed Pan-Head Machine Screw 72-8010 #10-32 X %-Inch Socket-Head Cap Screw 72-8812 #8-32 X ¥%-Inch Socket-Head Cap Screw 73-20807 4-Inch Diameter x 7,-Inch Long Spring Roll Pin 75-0488, #8 Split-Lock Washer 75-07020 0.390-Inch I. D. Flat Washer 040091-02 Right Handle 040091-01 Left Handle 040093-01 Right Handle Cover 040093-02 Left Handle Cover 040096-01 Button 040234-01 Steering Shaft 040235-01 60-Tooth Spur Gear 040237-01 Anchor Nut 040238-01 Anchor Pin 040239-01 Steering Torsion Spring 040240-01 Stop Bumper 040241-01 Spacer Bearing, 040242-01 Handle Shaft 040244-01 Spring Handle Pin 040246-01 Handle Torsion Spring 040249-01 14Tooth Spur Gear 040252-01 Compression Spring 040303-01 Trigger 040473-01 Jumper Wire 160026-001 SPDT Snap Switch 175002-001 0.750-Inch 1. D. Large Washer 175002-004 #10 Flat Washer 176022-3604 #6-32 x ¥4-Inch Self-Locking Socket-Head Cap Screw 176024-3605 #6-32 x H.-Inch Tamper-Proof Self-Locking Socket-Head Cap Screw 176022-3606 #6-32 x %-Inch Tamper-Proof Socket-Head Cap Screw 176025-3604 #6-32 X %-Inch Tamper-Proof Self-Locking Button-Head Cap Screw 176026-3610 #6-32 X %-Inch Tamper-Proof Socket-Head Cap Screw 177010-241 #10-32 Nylock Hex Nut 178012-001 Retaining Ring for .750-Inch Diameter Shaft 178101-003 28-Tooth Spur Gear

5-10

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

Illustrated Parts Lists STAR WARS COCKPIT

(AD40477-01 Rear Speaker Harness

79-561816P 040455-01 ‘WireNot Attraction Panel Retainer

A040451-01 Speaker Panel Assembly

040448-01 Corner Cap

039144-01 = 70098:00 Speaker Grille { P Tube Holder

‘A037540-01 Ground Wire 179125-001 Grounding Clip

040454-01 Attraction Panel Retainer 040460-01 Attraction Glass

NOTE ' To ensure that the fluorescent tube starts, makesure the ground wire is firmly attached to both the ballast transformer and the steel tube , bracket.

Figure 5-4 Fluorescent Tube and Speakers

Page 52

STAR WARS COCKPIT Illustrated Parts Lists

Fluorescent Tube and Speakers Parts List

Part No. Description

A040516-01 Fluorescent Tube Board Assembly—includes: A037540-01 Ground Wire with Ring Lug (not shown)— includes: 150006-755 18-Gauge Tinned Copper Wire, Green 179125-001 Grounding Clip (not shown) . A040480-01 ‘Tube Harness Assembly (not shown) 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) . A037458-01 18-Inch Fluorescent Tube Kit—includes: 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 037469-01 Steel Tube Bracket 142028-001 60 Hz, 118 V, Ballast Transformer 179035-001 2-Pin Fluorescent Tube Holder 04047701 Rear Speaker Harness Assembly 148001-017 6 x 9-Inch Oval, 8 2, 6-Ounce Magnet, Shielded High-Fidelity Speaker 040460-01 Attraction Glass with Graphics 040454-01 Lower Attraction Panel Retainer 040455-01 Upper Attraction Panel Retainer A040451-01 Speaker Panel Assembly—includes: A040478-01 Speaker Harness Assembly 039144-01 Speaker Grille 040448-01 Corner Cap 040449-01 Seat Speaker Panel 148001-013 6x 9-Inch Oval, 4 2, 6-Ounce Magnet, Shielded High-Fidelity Speaker

5-13

Page 53

Illustrated Parts Lists STAR WARS COCKPIT

A039254-01 Harness Assembly

Before removing or repairing the utilitypanel, tun the game off. Players| may receive an electrical shock ifthe utility panelis not properly grounded! After servicing any parts on the Panel, make sure that the ground wire is firmly attached to the bracket.

A002465-01 Coin Counter

69-001 SelfTest Switch 75-9910WO Stamped Nut 119006-103 040412-01 Volume Control Bracket

NOTE Only the Ireland-built cabinet has two coin counters. 62-041 Auxiliary Coin Switch

Figure 5-5 Utility Panel Assembly A040413-01 A Parts List

Part No. Description

A002465-01 Coin Counter A039254-01 Volume Control Harness Assembly (includes grounding clip) 62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 040412-01 Component Bracket 75-9910WO 15/32-32 Stamped Nut 119006-103 Volume Control 176018-002 #6-32 x %-Inch Machine Screw

5-14

Page 54

STAR WARS COCKPIT Mlustrated Parts Lists

170000-001 la mp a 179047001 9915023

Lamp Base Lp Base Plate

9915056 a Screw for Bezel 99-15026 99-15040 Coin Inlet Lever 99-15025 : Coin Inlet

99-15055 Retaining Screw a

  • 9815054

99-15027 Side Plate Coin Return

75-9148, Hex Nut

Lock Wash,

7214148 Screw

Figure 5-6 Vertically Mounted Coin Door 171034-xxx A Pivot for Lever

99-15028 Coin Return Box

5-15

Page 55

Illustrated Parts Lists

99-15067, Lock Assy.

A037542-01 Harness—not shown

99-15063 Screw “

99-15067 Lock Assy *

038091-01 Coin Box

99-15072 Door Frame

99-15073 Upper Door

99-15074 Lower Door 99-15070 Doors and Frame

171034-006 — U.K. 20 PI50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-001 -- U.S, 25¢/25¢ Coin Door 171034010 — German 2 DM/5 DM Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 99-15052

9915039 Bezel for Cover

99-15036

oe STAR WARS COCKPIT

99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

~ Spring for Button

99-15071 Clamp

99-15066 Screw

171034.011 — German 1 DWW5 DM Coin Door 171034-015 — French 2 Fit Fr Coin Door

Figure 5-6 Vertically Mounted Coin Door, continued 171034-xxx A

5-16 r

Page 56

STAR WARS COCKPIT Ulustrated Parts Lists

Vertically Mounted Coin Door Parts List

Part No. Description

A037542-01 Harness Assembly 72-1414S #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut

75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German I DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate

99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate

99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Meul Coin Return Cover 99-15038 Bezel for Coin Return Button

99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for US, 25¢ 99-15052 Spring for Coin Return Button

99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x %.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover

99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame

99-15071 Clamp for Frame 99-15072 Door Frame 99-15073, Upper Door 99-15074 Lower Door

99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly—Acceptable substitute is part number A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp. 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

5-17

Page 57

Illustrated Parts Lists STAR WARS COCKPIT

171006-035 99-10140 Coin mechanism Panel assy.

75-948S a Locknut . a

99-10152 Right coin inlet

75-9448

99-10151 Left coin inlet

99-10080 Lamp socket SS a 70-11-47 2x Lamp v4

F “

/ 99-10104 Bar retainer 72-9408S 5 Screw S 7 99-10147 7 Harness

99-10154 Bracket assy.

99-10042 thru 99-10045 oo-10153 Coin switch assy.

Coin return box 65-441C ee Coin switch ~ So Ia ‘ 99-10150 < —__—— >< < Z ‘Switch cover 99-10075 thru 99-10078 _~ Switch wire 99-10008 75-1412 Retainer Screw

Figure 5-7 American-Made Coin Door 171027-001 A

5-18

Page 58

STAR WARS COCKPIT

99-10139 Coin door

99-10119 Button assy. ) 9g.10118

72-JA1405B Screw

038091-01 Coin box

Figure 5-7 American-Made Coin Door, continued 171027-001 A Ilustrated Parts Lists

99-10142 Button housing

99-10134 Cover

Button

99-10115 Spring

98-10141 Coin return cover

99-10117 Coin return door

99-10144

@ Channel clip

99-10149 Service door g

5-19

Page 59

Illustrated Parts Lists

American-Made Coin-Door Assembly STAR WARS COCKPIT

Parts List

Part No. Description

171006-035 Metal Coin Mechanism for US. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HAI404C #4-40 x %-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 7514128 #4-40 x %-Inch Pan-Head Screw 75-9448 #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 9.10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, US. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-1018 Amber Coin Return Button 99-1019 Amber Coin Button for US. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-1014] Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143, Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam 99-10146 Coin Inlet Chute Assembly 9910147 American-Made Coin Door Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 9910154 Bracket Assembly

5-20

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 61

Illustrated Parts Lists STAR WARS COCKPIT

->———_NOTE. Power supply base plate is not shown. For part number, see Figure 5-4.

—d—WARNING Fuse block cover must be in place during game operation. A037395-01 (Transformer Assy.)

A021084-02 Voltage Plug *

29-053 A037479-02 (Capacitor) Voltage Plugs

034544-01 Fuse Cover

79-4411001 (Fuse Post) 78-70501SC. (Cap. Bracket) 46-2017002 * (Fuse) 46-2014002 Fuse

A035891-02 (Fuse Harness) 034482.02 (Chassis)

46-301203 (Fuse)

037639-01 (Label) * 037639-02 Label

78-2708 (Bushing)

A034630-01 Feira (Filter Assy.) 037641-01 46-2014002 (Label) i i (Fuses)

79-18021001 . 'A035890.01 (Term. Block) (Pwr. Harness)

3A-MDAQ5O1 oy A034620.01 (Rectifier) (AC. Harn.)

Figure 5-8 Power Supply Assembly US-Built A037396-04 F Ireland-Built A037396-06 F

5-22

Page 62

STAR WARS COCKPIT Ilustrated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.

For -04 Version

FL7 A, 250 V, 3AG Slow-Blow Glass Cartridge“Type Fuse46-2017002
FLLabel for Fuse Value037639-01
BVoltage Plug for 120 V (105-135 VAC) (yellow wire color—plugs into J3)A021084-02

For -06 Version

Fi4 A, 250 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse46-2014002
FlLabel for Fuse Value037639-02
BVoltage Block Assembly for 220 V (200-240 VAC) blue wire color; and 240 VA03 7479-02

(220-260 VAC) brown wire color

For -04 and -06 Versions

cl27,000 uF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3A-MDA3501
FLPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-4411001
FP4A, 250 V,3AG Slow-Blow Glass Cartridge‘Type Fuse (Acceptable substitute is46-2014002

Part no. 46-2014001, a 4 A, 125 V, 3AG Fuse)

F320 A, 32 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse46-301203
F4-F64 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (Acceptable substitute is46-2014002

part no. 46-2014001)

F2-F65-Position 3AG Fuse Block with 4 -Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037641-01
F42-Circuit Single-Row Terminal Block (located under F4)79-15021001
FLIRFI Filter Assembly (designation not marked)A034630-01
j2Power Harness AssemblyA035890-01
J4aAC Harness AssemblyA034629-01
TiTransformer Assembly (designation covered)A037395-01

Nylon Type 6/6 Hole Bushing with *%,-Inch Inside Diameter x 55/64-Inch 78-2708 Outside Diameter x %-Inch Thick Power Supply Chassis Base 034482-02

5-23

Page 63

STAR WARS COCKPIT Mlustrated Parts Lists

037873-01 Spacer A038463-21 Analog Vector-Generator PCB See Figure 5-13

A040472-01 Interconnect Cable

72-1604F 178120-112 Screw PCB Support

178120-212 NOTE PCB Suppor |i ‘The Federal Communications Comre mission requires that the game PCBs be housed in the EMI cage with the EMI Shield PCB attached. 178120-206 v PCB Support Laat A038461-21 Main PCB See Figure 5-12 175009-221 176015-112 Plastic Washer Screw 178044-242 Grommet

A040255-01 Interconnect PCB 178045-442 Fastener

A040260-21 Sound PCB See Figure 5-14 176021-004 Screw

A035435-02 Regulator/Audio ll PCB See Figure 5-11

A040301-01 Tray and Guides Assembly 178047-022 homme Guide jounting Tray

A037701-03 Grounding clip EMI Cage with Guides aaa not shown. ca is as EMI Shield PCB See Figure 5-10

Figure 5-9A PCB Mounting Hardware US-Built Cabinet

5-24

Page 64

STAR WARS COCKPIT Illustrated Parts Lists

PCB Mounting Hardware US-Built Cabinet Parts List

Part No. Description

A035435-02 Regulator/Audio II PCB A037701-03 EMI Cage and Guides Assembly—includes: 178047-032 16-Inch Snap-In PCB Guide (four required) 037700-02 EMI Cage A038461-21 Star Wars Main PCB Assembly A038463-21 Stars Wars Analog Vector-Generator PCB Assembly A040255-01 Stars Wars Interconnect PCB Assembly A040258-01 EMI Shield PCB Assembly— includes: 72-1404F #4-40 x %-Inch Cross-Recessed Steel Screw 037873-01 Spacer 175009-221 Plastic Washer 178044-242 Grommet 178045-442 Snap-In Fastener A040260-21 Stars Wars Sound PCB Assembly A040301-01 ‘Tray and Guides Assembly—includes: 040300-01 Mounting Tray for Regulator/Audio Il PCB 178047-022 11-Inch Snap-In PCB Guide (two required) A040472-01 Interconnect Cable 72-1604F #6-32 x %-Inch Cross-Recessed Pan-Head Screw 176015-112 #10 x %-Inch Cross-Recessed Pan-Head Screw 176021-004 #8 x %-Inch Zinc Hex Washer-Head Screw (2 screws attach the mounting tray to the EMI cage, and 1 screw attaches the Regulator/Audio II PCB to the mounting tray—acceptable substitute is part no. 176021-104) 178120-112 %-Inch PCB Support 178120-206 0.375-Inch PCB Support (located between the Main and Analog Vector-Generator PCB) 178120-212 %4-Inch PCB Support

5-25

Page 65

Illustrated Parts Lists STAR WARS COCKPIT

040722-01 Spacer A038463-21 Analog Vector-Generator PCB See Figure 5-13

A040472-01 Interconnect Cable

178120-112 PCB Support

178120-212 PCB Support

178120-206 = =>-1404F PCBSupport “Screw

A038461-21 Main PCB See Figure 512 A040725-01 Housing & Tray Assembly

040723-01 Housing

A040260-21 176015-112 t ZB Sound PCB Screw L£EE See Figure 5-14 A040255-01 Interconnect PCB

176021-004 Screw

Regulator/Audio ll PCB See Figure 5-11 034536-02 Analog Vector-Generator PCB See Figure 5-13 Yreoezon2 paA596 00 Guide

A040301-01 178047-032 ‘Tray and Guides Assembly Guide 040300-01 Main PCB 1 See Figure 5-12 Mounting Tray

Figure 5-9B PCB Mounting Hardware r ) Ireland-Built Cabinet

5-26

Page 66

STAR WARS COCKPIT Illustrated Parts Lists

PCB Mounting Hardware Ireland-Built Cabinet Parts List

Part No. Description

A035435-02 Regulator/Audio II PCB A038461-21 Star Wars Main PCB Assembly A038463-21 Stars Wars Analog Vector-Generator (AVG) PCB Assembly A040255-01 Stars Wars Interconnect PCB Assembly A040260-21 Stars Wars Sound PCB Assembly A040472-01 Interconnect Cable A040725-01 ‘Tray and Guides Assembly—includes: A040301-01 Mounting Tray and Guides for Regulator/Audio II PCB—includes: 040300-01 Mounting Tray 178047.022 I-Inch Snap-In PCB Guide (two required) A040724-01 PCB Guide Assembly—includes: 040723-01 PCB Housing 178047-032 16-Inch Snap-In PCB‘Guide (four required) 176021-004 #8 x %-Inch Zinc Hex Washer-Head Screw (attaches the Regulator/Audio II PCB to the mounting tray— acceptable substitute is part no. 176021-104) 72-1604F #6-32 x %-Inch Cross-Recessed Pan-Head Screw 034536-02 Foam Pad _(not shown) 040722-01 Spacer (not shown) 176015-112 #10 x %4-Inch Cross-Recessed Pan-Head Screw 178120-112 %-Inch PCB Support 178120-206, 0.375-Inch PCB Support (not shown—located between the Main and Analog Vector-Generator PCB) 178120-212 ¥%-Inch PCB Support

5-27

Page 67

Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Ata, Inc., Sunnyvale, CA. This drawingis only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF license to use, the sub- Ject matier of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any parhereof. Except for manofactre by vendor of Ari In. and for manufacture under the corporation's written license, no right toteproduce this drawing is granted or the subject matter thereof tanless by written agreement with or written permisston from the corporation

Figure 5-10 EMI Shield PCB Assembly cée + ce3 fo

cee

Cé9 fo C3! fo C32 f+ 033-4 0344

C36 C37 o> C38 Go C3940} C40 fo

co8 For Al

> 6.45 470 pt C40 47056 C47 470p¢ C46 420p+ C49 4270p = C50 470pe

o> C52 cO-c53 Cm c54 <o-¢55

A040258-01 A )

N

fl STAR WARS COCKPIT

Page 68

STAR WARS COCKPIT Illustrated Parts Lists

EMI Shield PCB Assembly Parts List

Part No. Description

Capacitors

C1-Cl60.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
Ccl70.01 uF, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103
C21-C230.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C260.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
c290.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C31-C340.1 pF, + 80% -20%, 50 V, Ceramic Capacitor122002-104
C360.01 pF, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103
C37-C400.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C45-C50470 pF, 100 V, Ceramic Axial-Lead Capacitor122016-471
C52-C640.1 wF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C680.1 AF, +80% -20%, 50 V, Ceramic Capacitor122002-104

Connectors

P1930-Pin Edge Connector (Acceptable substitute is part no. 179046-030)179073-030
P2044-Pin Edge Connector (Acceptable substitute is part no. 179046-044)179073-044

Miscellaneous Spacer 037873-02 #4-40 x.% Cross-Recessed Pan-Head Screw 72-1404F 4-Inch Grommet 178044-242 %-Inch White Plunger 178045-442 Flat Nylon Washer 175009-221

5-29

Page 69

Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific ‘written permission of Atari, Inc., Sunnyvale, CA. This drawingis only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or licensetouuse, the subject matter ofthe drawing or any design or techrical information shown thereon, nor any right to reproduce this drawing or any art thereof. Except for: ire by vendors of Atari, Inc., and for manufacture under the corporation's written license, no ti to teptoduce this drawingis granted or the subject matter thereof unless by written agreement with or written permission from the ‘corporation, STAR WARS COCKPIT

Q = 3 L =| 0

ae 0 cas nN + 3300 L— 35V

  • $38 + [ C23 cai
35Vfer}foe}

Arr} p22

B52B25c22,¢

fo) a) f 4n5wp=08 Oop 7812 7905

  • R24,10.,7WI Oo
TIP 32_TOA2ZO02ATDA2002A
Talenacom QsQ

creo i R54 + ne

cogaAC7BSce confi’

co@@ |,,9| cscEn m8 mmRis |OO| Rega De 1 220] R21, \/2w

HE)4octeyb

ar cricid]

40thcael

Cio BB00uF + 35V

+ 3500. 35v. y “| 9 220 RO R9,1/2W Hist cry ~LFwacoz Je mo —t 4 o @

Figure 5-11 Regulator/Audio II PCB Assembly

5-30 A035435-02 G

Page 70

STAR WARS COCKPIT Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 uF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.29-088

122002-104

C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
csOL pF, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.100015-103

122005-103)

C60.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
c70.001 uF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
Cll0.1 wF, 25 V, Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.29-088.

122002-104

cl2470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cls1000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
cl4.O1 wF, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.100015-103

122005-103)

cis.0.22 pF, 25 V, Ceramic-Dise Axial-Lead Capacitor122004-224
C160.001 uF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cl70.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24350338
20, C210.1 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.29-088

122002-104

C22, C231 wF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105,
C2422 pF, 35 V, Aluminum ElectrolyticFixed Axial-Lead Capacitor24-350226
C3l22 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350226

Diodes

CRIType-IN4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002
CR4Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8Type-IN5401, 3 A, 100 V Silicon Rectifier Diode31-IN5401

Resistors

RL2700, 25%, 4 W Resistor110000-271
R333.0, +5%, %& W Resistor110000-330
R41000, +5%, % W Resistor110000-101
RS2.70, +5%, 1 W Resistor110009-027
RG3.9kQ, +5%, % W Resistor110000-392
R77.5 kQ, +5%, % W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer (Acceptable substitute is part19-315102

no. 119002-102)

RO2200, +5%, % W Resistor110001-221

(Continued on next page)

5-31

Page 71

Illustrated Parts Lists STAR WARS COCKPIT

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
RIO19, 45%, %& W Resistor110000-010
Ru102, +5%, % W Resistor110000-100
R121000, +5%, % W Resistor110000-101
R13, R1410kQ, +5%, % W Resistor110000-103
R20100, +5%, 4 W Resistor110000-100
R2l2200, +5%, %% W Resistor110001-221
RID1Q, 45%, 4 W Resistor110000-010
R221002, +5%, 4 W Resistor110000-101
R240.1.0, £3%, 7 W Wirewound Resistor19-100P1015
R254Q, +5%, 5 W Wirewound Resistor116001-040
R27, R281kQ, +5%, 4 W Resistor110000-102
R29, R3010Q, +5%, 4 W Resistor110000-100
R31229, +5%, 10 W Wirewound Resistor116000-220
R32, R335.6kQ, +5%, %& W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
@‘Type-2N3055 NPN Silicon Transistor34-2N3055

Miscellaneous

J66-Position Connector Receptacle79-58306
irs9-Position Connector Receptacle79-58308
Js4-Position Connector Receptacle79-58354
jo6-Position Connector Receptacle79-58306
yo12-Position Connector Receptacle79-58346
a5 V Linear Voltage Regulator37-LM305
Q2, Q9Thermally ConductiveSilicon Insulator78-16014
3Thermally Conductiveon Insulator78-16008
QOAudio Amp TDA2002A137151-002
Q7Audio Amp TDA2002A137151-002
QsType-7812 +12 V Voltage Regulator37-7812
Q9Type-7905 -5 V Voltage Regulator37-7905

Heat Sink 034531-01 Test Point (Acceptable substitute is part no. 020670-01) 179051-001

Page 72

1" 10 9 8 7 6 5 4 3 2 1 we i rz) es = ‘6 = f

i

i bY 3} foes] | med ee) '

aed Cane 4) Ei Sse) Saad es STAR WARS COCKPIT

° qt v i = a ar 238 iG = 4 2 H Seo aos} Sua = Saar baa] 4

eer]

mT Sede Soeg [(-o7! Saas) ear 27d ee (as

are St 9 Becss?

e Saag] Tea) ae <s4.cn

A038461-21 A fezned aia} [evan Zaas Ss a c==7 f 27C4

Pears oar = =a we

ied Saxo] pas) Sexe] aaa] casa re | soo rae Fi Sa] Se Se) = SH sed =

Figure 5-12 Main Printed-Circuit Board Assembly : we a2 8 BI (ke. wveoss Sel Saas a as) Sas} Sse sa ogee D TAN eee 1 28tsoy WEY fiom tem oe tee Os ho “(il 5

5-33 Illustrated Parts Lists

Page 73

Illustrated Parts Lists STAR WARS COCKPIT

Main Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl0.1 pF, +5%, 50 V Ceramic Capacitor122002-104
C2100 pF, 100 V Mica Capacitor128002-101
C339 pF, 100 V Mica Capacitor128002-390
C4-C200.1 pF, +5%, 50 V Ceramic Capacitor122002-104
C45-C480.1 pF, +5%, 50 V Ceramic Capacitor122002-104
C49-C510.100 #F, 35 V Electrolytic Capacitor24-350107
C52-C920.1 hE, +5%, 50 V Ceramic Capacitor122002-104
Co0.10 uF, 35 V Electrolytic Capacitor24-350106
C944,7 pF 35 V Electrolytic Capacitor124000-475
C95, C960.1 pE, +5%, 50 V Ceramic Capacitor122002-104

Diodes

CRIType-IN914 Diode31-1N914
CR2Red Light-Emitting Diode38-MV5053
CR3Type-IN914 Diode31-IN914
CR4-CR6Red Light-Emitting Diode38-MV5053

Integrated Circuits

VRI5 V Fixed Regulator Integrated Circuit37-7805
OBIC3-8 Line Decoder Integrated Circuit137177-001
ODIETri-State Octal Bus Transceiver Integrated Circuit37-74L8245
1BLine Driver/Receiver Integrated Circuit37-74LS244
1cLine Driver/Receiver Integrated Circuit37-74L8244
1ENonVolatile RAM Integrated Circuit137288-001
IF300 ns Tri-State EROM Integrated Circuit136021-101
1H300 ns Tri-State EROM Integrated Circuit136021-102
WK300 ns Tri-State EROM Integrated Circuit136021-103
IK/L300 ns Tri-State EROM Integrated Circuit136021-104
1M300 ns Tri-State EROM Integrated Circuit136021-106
INQuad 2-Input NOR Gate Integrated Circuit37-74804
2cMicroprocessor137249-120
2E/FLine Driver/Receiver Integrated Circuit37-74LS244
20H150 ns Tri-State Static RAM Integrated Circuit1372-001
2yDual 2-4 Decoder/Multiplexer Integrated Circuit37-7ALS139
2KHex Inverter Integrated Circuit37-74LS08
2L3-8 Line Decoder Integrated Circuit137177-001
2MDual DType Flip-Flop Integrated Circuit37-74LS74
2N4-Bit Counter Integrated Circuit37-74LSI61
2PDual 4-Bit Bin Counter Integrated Circuit37-7418393
2RDual 4-Bit Bin Counter Integrated Circuit37-74LS393,
3DUp-Down Counter Integrated Circuit37-74LS191
3EUp-Down Counter Integrated Circuit37-74LS191

5-34 (continued on next page)

Page 74

STAR WARS COCKPIT Illustrated Parts Lists

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
3FUp-Down Counter Integrated Circuit37-74LS191
3HQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
3Data Selector/Multiplexer Integrated37-74LS153
3KData Selector/Multiplexer Integrated.37-74LS153
3LQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
3MType-74LS00 Integrated Circuit37-74LS00
3NShift/Storage Register Integrated Circuit137180-001
3PQuad 2-Input NOR Gate Integrated Circuit37-74LS04
3R4-Bit Counter Integrated Circuit37-74LS161
4DShift/Storage Register Integrated Circuit137180-001
4E‘Tri-State Octal Bus Transceiver Integrated Circuit377418245,
4FTri-State Octal Bus Transceiver Integrated Circuit37-7418245
4HTri-State Octal Bus Transceiver Integrated Circuit37-74LS245,
4)Line Driver/Receiver Integrated Circuit37-74LS244
4KLine Driver/Receiver Integrated Circuit37-T4LS244
4L, SLOctal D-Type Flip-Flop Integrated Circuit37-74LS374
4M, 5MOctal D-Type Flip-Flop Integrated Circuit37-74LS374
4N-ON4-Bit Counter Integrated Circuit37-74LS83
4P-6PQuad D-lype Flip-Flop Integrated Circuit37-74LS175,
5BQuad Exclusive OR Integrated Circuit37-74LS86
5C8-Bit Register Counter Integrated Circuit37-74LS164
5D8-Bit Register Counter Integrated Circuit37-74LS164
SE, OEHex Inverter Integrated Circuit37-74LS08
SF150 ns Tri-State Static RAM Integrated Circuit137211-001
SH150 ns Tri-State Static RAM Integrated Circuit137211-001
sy8-Bit Register Counter Integrated Circuit37-74LS164
5K8-Bit Register Counter Integrated Circuit37-74LS164
5RDual 1-of-4 Decoder/Multiplexer Integrated Circuit137221-001
OA8-Bit Register Counter Integrated Circuit37-74LS165,
6B8-Bit Register Counter Integrated Circuit37-74LS165
6C, 7CTwo's-Complement, Serial Multiplexer Integrated Circuit137182-001
6D, 7DShift/Storage Register Integrated Circuit137180-001
6FData Selector/Multiplexer Integrated Circuit37-74LS153
6HUp-Down Counter Integrated Circuit37-74LS191
aUp-Down Counter Integrated Circuit37-74LS191
OKHex Inverter Integrated Circuit37-74LS08
6LQuad D‘Type Flip-Flop Integrated Circuit37-74LSI75
6M4-Bit Counter Integrated Circuit37-74LS83
ORDual D-Type Flip-Flop Integrated Circuit37-74LS74
7A8-Bit Register Counter Integrated Circuit37-74LS165,
7B8-Bit Register Counter Integrated Circuit37-74LS165
JEType-74LSO00 Integrated Circuit37-74LS00,
TFType-74LS00 Integrated Circuit37-74LS00
7HROM Integrated Circuit136021-110

(continued on next page)

5-35

Page 75

Illustrated Parts Lists STAR WARS COCKPIT

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
aROM IntegratedCircuit136021-111
7KROM IntegratedCircuit13602i-112
7LROM Integrated Circuit136021-113
7™MShift/Storage Register Integrated Circuit137180-001
7N3-8 Line Decoder Integrated Circuit137177-001
7PDual D-Type Flip-Flop Integrated Circuit37-74LS74
BADual D-type Flip-Flop Integrated Circuit37-TALS74
8BQuad Serial Adder/Subtractor Integrated Circuit137181-001
8CHex Inverter Integrated Circuit37-74LS08B
8D‘Type-74LS00 Integrated Circuit37-74LS00
8EQuad 2-Input NOR Gate Integrated Circuit37-7402
8FTriple 3-Input NAND Gate Integrated Circuit137236-001
8HDual D-Type Flip-Fiop Integrated Circuit37-TALST4
8KQuad 2-Input NOR Gate Integrated Circuit37-74LS04
8L.3-8 Line Decoder Integrated Circuit137177-001
8M3-8 Line Decoder Integrated Circuit137177-001
8NType-74LS00 Integrated Circuit37-741800
8PDual J-K Flip-Flop Integrated Circuit37-74LS109
8RUp-Down Counter Integrated Circuit37-74LS191
oA8-Bit Register Counter Integrated Circuit37-74LS164
OB8-Bit Register Counter Integrated Circuit37-T4LS164
9C, 10C4-Bit Counter Integrated Circuit37-74LS161
9D4-Bit Counter Integrated Circuit37-74LSI161
9ELine Driver/Receiver Integrated Circuit37-74L8244
OFLine Driver/Receiver Integrated Circuit37-741S244
9HLine Driver/Receiver Integrated Circuit37-741S244
9gLine Driver/Receiver Integrated Circuit37-74LS244
OKAnalog/Digital Converter Integrated Circuit137243-001
9LIM.8-Bit Latch Integrated Circuit37-74LS259
10LHex Buffer/Driver Integrated Circuit37-7407
10RHex Inverter Schmitt Trigger Integrated Circuit37-7ALSI4
11INDual Operational Amplifier Integrated Circuit37TLO82CP

Resistors

RI, R210 kQ, +5%, % W Resistor110000-103
R32200, +5%, 4 W Resistor110000-221
R41kQ, +5%, %& W Resistor110000-102
RS10 kQ, +5%, 4 W Resistor0000-103
RG100 kQ, +5%, % W Resistor110000-104
R72200, +5%, % W Resistor110000-221
R815 kQ, +5%, % W Resistor110000-153,
R9, RIO1kQ, 45%, 4 W Resistor110000-102
RU, RI210kQ, +5%, % W Resistor110000-103
R13, R142200, +5%, % W Resistor110000-221
RIS10k, +5%, 4 W Resistor110000-103

(continued on next page)

Page 76

STAR WARS COCKPIT

Main Printed-Circuit Board Assembly Illustrated Parts Lists

Parts List, continued

DesignatorDescriptionPart No.
RIG, RI71kQ, +5%, 4 W Resistor110000-102
RI8-R21470 2, +5%, % W Resistor110000-471
R22-R251k@, +5%, %& W Resistor110000-102
R26-R33,470 2, +5%, % W Resistor110000-471
R34-R411k@, +5%, % W Resistor110000-102
R42-R5710 kQ, +5%, % W Resistor110000-103,
R582202, +5%, % W Resistor110000-221
R79-R81100 2, +5%, %& W Resistor110000-101
R82-R864.7kQ, +5%, % W Resistor110000-472
ROL1509, +5%, % W Resistor110000-151
R92-R971kQ, +5%, % W Resistor110000-102
RIOO22 kQ, +5%, % W Resistor110000-223

Sockets

1E18 Conuct, Medium-Insertion-Force IC Socket79-42C18
1F28 Contact, Medium-Insertion-Force IC Socket79-42C28
1H)28 Contact, Medium-Insertion-Force IC Socket79-42C28
WK28 Contact, Medium-Insertion-Force IC Socket79-42C28
IK/L28 Contact, Medium-Insertion-Force IC Socket79-42C28
1M28 Contact, Medium-Insertion-Force IC Socket79-42C28
2C40 Contact, Medium-Insertion-Force IC Socket79-42C40
2F/H24 Contact, Medium-Insertion-Force IC Socket79-42C24
SF24 Contact, Medium-Insertion-Force IC Socket79-42C24
SH24 Contact, Medium-Insertion-Force IC Socket79-42C24
7H18 Contact, Medium-Insertion-Force IC Socket79-42C18
718 Conuct, Medium-Insertion-Force IC Socket79-42C18
7K18 Contact, Medium-Insertion-Force IC Socket79-42C18
TL,18 Contact, Medium-Insertion-Force IC Socket79-42C18.
OK28 Conuct, Medium-Insertion-Force IC Socket79-42C28

Switches

10D8-Toggle DIP Switch66-118PIT
10EToggle DIP Switch66-18PIT
ML4-Toggle DIP Switch66-114PIT

Transistors

QlType-2N3904 Transistor34-2N3904
Q3, Q4Type-2N6044 Transistor34-2N6044

Miscellaneous Test Point Acceptable substitute is part no. 020670-01 179051-002

LLFixed RF +5%, 100Q InductorAcceptable substitute is part no. 141002-00141-3003,
JIGA2-Contact Header Connector79-58255,
JIGB4-Conuct Header Connector79-58331
Q3Nylon Snap-In Fastener81-4302
Q4Nylon Snap-In Fastener81-4302
VRINylon Snap-In Fastener81-4302
Yi12.096-MHz Crystal144000-001

5-37

Page 77

STAR WARS COCKPIT

design or te

to reproduce

snufacture by vendors ‘corpora

to reproduce this drawing i

unless by written agreement

corporation. Illustrated Parts Lists

Figure 5-13 Analog Vector-Generator (AVG) PCB Assembly A038463-21 A

5-38

Page 78

STAR WARS COCKPIT

Analog Vector-Generator (AVG) PCB Assembly Illustrated Parts Lists

Part No. Parts List

Designator Description

Capacitors Cl-C3 0.1 uF, +80% -20%, 50 V Ceramic Capacitor C4, C5 0.01 pF, 100 V Mylar Capacitor C6, C7 0.1 pF, +80% -20%, 50 V Ceramic Capacitor c8 0.047 uF, + 10%, 50 V Polycarb Axial-Lead Capacitor

C9-C12 0.1 uF, +80% -20%, 50 V Ceramic Capacitor cl4 0.1 pF, +80% -20%, 50 V Ceramic Capacitor C17-C20 0.1 pF, +80% -20%, 50 V Ceramic Capacitor C21 0.01 pF, 100 V Mylar Capacitor

C25 0.047 uF, + 10%, 50 V Polycarb Axial-Lead Capacitor C26-C28 0.1 uF, +80% -20%, 50 V Ceramic Capacitor C31 0.1 uF, +80% -20%, 50 V Ceramic Capacitor C35, C36 0.1 pF, +80% -20%, 50 V Ceramic Capacitor

C37 150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor C38 39 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor 39, C40 0.1 pF, +80% -20%, 50 V Ceramic Capacitor C41 0.01 uF, 50 V Ceramic Capacitor

C42 10 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor C43, C44 100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor C45 22 uF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor C46 100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor

C47 150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor C48 22 uF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor C50-C65, 0.1 uF, +80% -20%, 50 V Ceramic Capacitor C66 150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor C67-C80 0.1 uF, +80% -20%, 50 V Ceramic Capacitor C81 100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor C82 0.1 pF, +80% -20%, 50 V Ceramic Capacitor C83 22 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor

Coils LI-L3 830 mA, 0.29, +10%, 1.0 #H, Peaking Coil Inductor

Diodes cRI Type-IN914 Diode CR2 Type-MV5053 Red Light-Emitting Diode CR3, CR4 Type-IN100 Diode

Integrated Circuits 1A Quad 2-Input AND Gate Integrated Circuit 1B 4-Bit Counter Integrated Circuit 1c 4-Bit Counter Integrated Circuit 1D 4-Bit Counter Integrated Circuit

1E Quad 2-Input NOR Gate Integrated Circuit IF Triple 3-Input NOR Gate Integrated Circuit 1H Dual D-Type Flip-Flop Integrated Circuit IK ‘Tri-State Octal Bus Transceiver Integrated Circuit

(continued on next page) 122002-104 21-101103 122002-104 122010-473

122002-104 122002-104 122002-104 21-101103

122010-473 122002-104 122002-104 122002-104

128002-151 128002-390 122002-104 27-500103

128002-100 24-350107 24-250226 24-350107

128002-151 24-250226 122002-104 128002-151

122002-104 24-350107 122002-104 128002-220

141007-001

31-IN914 38-MV5053, 31-1N100

37-74LS08 37-74LS161 37-74LS161 37-74LS161

37-74LS02 37-7ALS27 37-74LS74 37-74L8245

Page 79

Illustrated Parts Lists STAR WARS COCKPIT

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
ILRead-Only Memory Integrated Circuit136021-105
IMLine Driver/Receiver Integrated Circuit37-741S244
INLine Driver/Receiver Integrated Circuit37-74L8244
iPLine Driver/Receiver Integrated Circuit37-741S244
2ADual 4-Input NAND Gate Integrated Circuit37-74LS20
2B4-Bit Counter Integrated Circuit37-741S161
2c‘Triple 3-Input Positive AND Gate Integrated Circuit137149-001
2DDual D-Type Flip-Flop Integrated Circuit37-74LS74
2EQuad 2-Input OR Gate Integrated Circuit37-74LS32
2FDual J-K Flip-Flop Integrated Circuit37-74109
2HQuad 2-Input ANDGate Integrated Circuit37-74LS08
2Vector-Generator Integrated Circuit137179-001
2K4 to 10 Decoder Integrated Circuit37-74LS42
2MLine Driver/Receiver Integrated Circuit37-74LS244
2NLine Driver/Receiver Integrated Circuit37-74LS244
3AQuad 2-Input NAND Gate Integrated Circuit37-74LS00
3BHex D-Iype Flip-Flop Integrated Circuit37-74LS174
3cQuad D{Type Flip-Flop Integrated Circuit37-74LSI75
3D4 to 10 Decoder Integrated Circuit37-741S42
3EQuad 2-Input NOR Gate Integrated Circuit37-74802
3F74S260 Integrated Circuit37-748260
3HQuad 2-Input NOR Gate Integrated Circuit37-74LS02
3L150 ns Tri-State Static RAM Integrated Circuit137211-001
3M150 ns Tri-State Static RAM Integrated Circuit137211-001
3P150 ns Tri-State Static RAM Integrated Circuit137211-001
4AQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
4BRead-Only Memory Integrated Circuit136021-109
4CQuad Data Selector/Multiplexer Integrated Circuit37-TALSIST
4DHex, Schmitt/Trigger Integrated Circuit37-74L814
4EQuad 2-Input NAND Gate Integrated Circuit37-74S00
4FQuad 2-Input Exclusive-OR Gate Integrated Circuit137002-001
4HQuad D-lype Flip-Flop Integrated Circuit37-74LSI75
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4M150 ns Tri-State Static RAM Integrated Circuit137211-001
4P150 ns Tri-State Static RAM Integrated Circuit137211-001
5AShift Register Integrated Circuit37-741S194
5BShift Register Integrated Circuit37-74LS194
5CShift Register Integrated Circuit37-74LS194
5EOctal D-Type Flip-Flop Integrated Circuit37-74LS273
SFShift Register Integrated Circuit37-74LS194
5HShift Register Integrated Circuit37-74LS194
3Quad 2-Input OR Gate Integrated Circuit37-74LS32
SKDual DType Flip-Flop Integrated Circuit37-748 74

5-40 (continued on next page)

Page 80

STAR WARS COCKPIT Illustrated Parts Lists

Analog Vector-Gencrator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
5LQuad D-Type Flip-Flop Integrated Circuit37-74LS175
5MQuad D-Type Flip-Flop Integrated Circuit37-74LS175,
SPHex Inverter Integrated Circuit37-74804
6AIB12-Bit D-A Converter, Integrated Circuit137158-002
6D8-Bit D-A Converter, Integrated Circuit137159-001
6E12-Bit D-A Converter, Integrated Circuit137158-002
OFOctal D‘Type Flip-Flop Integrated Circuit37-74LS273,
oHShift Register Integrated Circuit37-7ALS194
6Triple 3-Input NAND Gate Integrated Circuit137236-001
6KHex Inverter Integrated Circuit37-74LS04
OL.Quad Dlype Flip-Flop Integrated Circuit37-7ALS175,
6MUp/Down Counter Integrated Circuit37-7ALSIOL
7ADual Operational Amplifier Integrated Circuit37TLO82CP
7BLF13201 Quad Analog Switch, Integrated Circuit3713201
7DDual Operational Amplifier Integrated Circuit37TLO82CP
JELF13201 Quad Analog Switch, Integrated Circuit3713201
8BICDual Operational Amplifier Integrated Circuit37TLO82CP
8F8-Bit D-A Converter, Integrated Circuit137159-001
8LHex Buffer/Driver Inverter integrated Circuit37-7407
8MQuad 2-Input NOR Gate Integrated Circuit37-74LS02
8N8-Bit Register Counter Integrated Circuit37-74LS164
9BICDual Operational Amplifier Integrated Circuit37TLO82CP
oFDual Operational Amplifier Integrated Circuit37TLO82CP
VRL1A, 15 V, Fixed Regulator Integrated Circuit37-7815
VR21A, -15 V, Fixed Regulator Integrated Circuit37-7915

Resistors

R1-R1O10 kQ, +5%, %& W Resistor110000-103,
RIL12 kQ, +5%, 4 W Resistor110000-123
R1224kQ, +5%, % W Resistor110000-243
R1347 kQ, +5%, % W Resistor110000-473
RI48200, +5%, %« W Resistor110000-821
RIS150kQ, +5%, % W Resistor110000-154
RIG12 kQ, +5%, % W Resistor110000-123
RI76.2 kQ, +5%, % W Resistor110000-622
R20-R224702, +5%, % W Resistor110000-471
R23-R254.7kQ, +5%, % W Resistor110000-472
R268202, +5%, % W Resistor110000-821
R278202, +5%, 4 W Resistor110000-821
R30, R317.5 kQ, +1%, % W Resistor110003-752
R4110 k@ Potentiometer119002-103
R42150 kQ, +5%, & W Resistor110000-154
R432.7kQ, +5%, 4 W Resistor110000-272
R4410 kQ Potentiometer119002-103
R456.8k2, +5%, % W Resistor110000-682
R4622 kQ, +5%, % W Resistor110000-223
R472 kQ Potentiometer119002-202

(continued on next page)

5-41

Page 81

illustrated Parts Lists STAR WARS COCKPIT

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R511002, 45%, % W Resistor0000-101
R548200, +5%, 4 W Resistor110000-821
R55,8200, +5%, % W Resistor110000-821
R587.5kQ, +1%, & W Resistor110003-752
ROB10 kQ Potentiometer119002-103
R69150 kQ, +5%, % W Resistor110000-154
R702.7 kQ, +5%, % W Resistor110000-272
R7110 kQ Potentiometer119002-103
R726.8kQ, +5%, 4 W Resistor110000-682
R7322 kQ, +5%, 4 W Resistor110000-223
R742 kQ Potentiometer119002-202
R75, R761.3kQ, +1%, 4 W Resistor110000-132
R78100 2, +5%, % W Resistor110000-107
R8115k, +5%, % W Resistor110000-153
R821kQ, +1%, %4 W Resistor110000-102
R8310 kQ, +5%, 4 W Resistor110000-103
R84560.2, +5%, % W Resistor110000-561
R85, R8675kQ, +1%, % W Resistor110003-752
R876.19 kQ, +1%, % W Resistor110003-622
R88200 © Potentiometer119002-201
R897.5 kQ, +1%, % W Resistor110003-752
R901009, +5%, % W Resistor110000-101
ROL6.19 kQ, +1%, % W Resistor110003-622
R92200 Q Potentiometer119002-201
R9375 kQ, £1%, % W Resistor110003-752
R941002, 45%, % W Resistor110000-101
R95, ROG75.kQ, +1%, % W Resistor110003-752
R973.9k2, +5%, %& W Resistor110000-392
R98-R105100 kQ, +5%, 4 W Resistor110000-104
R1067.5 kM, +1%, % W Resistor110003-752
R1071509, +5%, % W Resistor110000-151
RIO9-RIL1kQ, +1%, % W Resistor110000-102
R112, R1310 KR, +5%, 4 W Resistor110000-103
R114-R1161002, +5%, % W Resistor110000-101
RZ10k, +5%, % W Resistor110000-103,
RVI, RV28 V Variable Resistor110004-001
VRI, VR2Nylon Snap-In Fastener81-4302

Sockets

IL24 Contact, Medium-Insertion-Force IC Socket79-42C24
2J40 Contact, Medium-Insertion-Force IC Socket79-42C40
3L24 Contact, Medium-Insertion-Force IC Socket79-42C24
3M24 Contact, Medium-Insertion-Force IC Socket79-42C24
3P24 Contact, Medium-Insertion-Force IC Socket79-42C24
4L24 Contact, Medium-Insertion-Force IC Socket79-42C24
4M24 Contact, Medium-Insertion-Force IC Socket79-42C24
4P24 Contact, Medium-Insertion-Force IC Socket79-42C24

Transistors

a‘Type-2N3904 Transistor3.4-2N3904
Q4-Q7Type-2N3904 Transistor34-2N3904
Q8Type-2N3906 Transistor34-2N3906

Miscellaneous Test Point 179051-002

5-42

Page 82

Illustrated Parts Lists

(e)

wisn NI 3QVW [Wage “dB GNNOS SHVM

cal a i FI

uv

  • ! 3 F < r id 8 : i zal i

E = Fil 5 C go E | lose 40 « al ag Ce i] 7 i

5D [3]

-01 A A040260.

5-43 STAR WARS COCKPIT

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

forbidden without the specific written permission of Atari, inc., Sunnyvale, CA,

‘issued, receipt not possession thereof confers or transfers an}

yy design or technical information shown

re y vendors of At

to repraduce this drawing is {en permission from the corporation,

eon,

Page 83

Ilustrated Parts Lists STAR WARS COCKPIT

Sound PCB Assembly Parts List

DesignatorDescriptionPartNo.

Capacitors

Cl-C120.1 pF, 50 V, Ceramic Capacitor122002-104
C13-C15100 wF, 35 V, Aluminum Electrolytic Capacitor24-350107
C16-C200.1 pF, 50 V, Ceramic Capacitor122002-104
C22-C280.1 pF, 50 V, Ceramic Capacitor122002-104
C291000 pF, 50 V, Monolithic Ceramic Capacitor122002-102
C30-C320.1 pF, 50 V, Ceramic Capacitor122002-104
C331000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
C340.1 pF, 50 V, Ceramic Capacitor122002-104
C351000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
C36-C380.1 pF, 50 V, Ceramic Capacitor122002-104
C391000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
C40-C43,0.1 pF, 50 V, Ceramic Capacitor122002-104
C440.01 pF, 25 V, Ceramic Capacitor122005-103
C450.1 pF, 50 V, Ceramic Capacitor122002-104
C460.0027 pF, 50 V, Ceramic Capacitor122015-272
C47100 uF, 35 V, Aluminum Electrolytic Capacitor24-350107
C48-C500.0027 pF, 50 V, Ceramic Capacitor122015-272
C510.47 pF, 50 V, Aluminum Electrolytic Axial-Lead Capacitor124001-474
C5210 pF, 25 V, Aluminum Electrolytic Capacitor24-250106
C53100 #F, 35 V, Aluminum Electrolytic Capacitor24-350107
C54, C55.6.1 wE, 50 V, Ceramic Capacitor122002-104
C56-C580.0027 pF, 50 V, Ceramic Capacitor122015-272
C59-C610.1 #F, 50 V, Ceramic Capacitor122002-104

Connectors

P24-Contact Header-Connector179165-004
P32-Contact Header-Connector179165-002

Diodes

DSIType-MV5053 Red Light-Emitting Diode38-MV5053

Integrated Circuits

1c/DSpeech Synthesizer Integrated Circuit137308-001
IEV/O and Internal Timer Memory Integrated Circuit90-6018
1F/H150 ns Tri-State Static RAM Integrated Circuit137211-001
1HROM Integrated Circuit136021-108
YKROM Integrated Circuit136021-107
2BQuad Operational Amplifier Integrated Circuit37-347
2DAudio Integrated CircuitCO12294-01
2FType-74C04 Integrated Circuit137309-001
2H‘Type-741S04 Integrated Circuit37-7ALSO4
PAI‘Type-74LS139 Integrated Circuit37-7ALSI39
3AType-556 Integrated Circuit37-556
3B512 Delay Line Integrated Circuit137310-001

5-44 (continued on next page)

Page 84

STAR WARS COCKPIT Illustrated Parts Lists

Sound PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
3CQuad Operational Amplifier Integrated Circuit37-347
3DAudio Integrated CircuitCO12294-01
3FType-74LS161 Integrated Circuit37-74LS161
3H‘Type-74LS00 Integrated Circuit37-74LS00
3JType-74LS139 Integrated Circuit37-74LS139
3KMicroprocessor137249-120
4CQuad Operational Amplifier Integrated Circuit37-347
4DAudio Integrated Circuit€O12294-01
5DAudio Integrated CircuitC€O12294-01
SFType-74LSI161 Integrated Circuit37-74LS161
SH‘Type-74LS125 Integrated Circuit137317001
SHType-74LS74 Integrated Circuit37-TALS74
JType-74LS374 Integrated Circuit37-74LS3 74
SKType-74LS374 Integrated Circuit37-74LS374

Resistors

RL1kQ, +5%, 4 W Resistor110000-102
R2, R310kQ, +5%, % W Resistor110000-103
R41kQ, +5%, % W Resistor110000-102
R5, R610k®, +5%, % W Resistor110000-103,
R71509, +5%, % W Resistor110000-151
R1010kQ, +5%, % W Resistor110000-103
Ri3.3kQ, +5%, % W Resistor110000-332
R121kQ, +5%, % W Resistor110000-102
R1310 kQ, +5%, % W Resistor110000-103,
R143.3 KO, +5%, % W Resistor110000-332
RIS1kQ, +5%, % W Resistor110000-102
RIG3.3 kQ, +5%, % W Resistor110000-332
RI710 kf, +5%, % W Resistor110000-103
RIS18kQ, +5%, % W Resistor110000-182
RID100 k®, +5%, % W Resistor110000-104
R201kQ, +5%, % W Resistor110000-102
R2147kQ, +5%, % W Resistor110000-473
R221kQ, +5%, % W Resistor110000-102
R2347kQ, +5%, % W Resistor110000-473
R241kQ, +5%, % W Resistor110000-102
R2582k, +5%, % W Resistor110000-823,
R261kQ, +5%, % W Resistor110000-102
R2782 kQ, +5%, %4 W Resistor110000-823
R28100 KO, +5%, 4 W Resistor110000-104
R2915 kQ, +5%, % W Resistor110000-153,
R3012 kQ, +5%, % W Resistor110000-123,
R31, R32560 kQ, +5%, % W Resistor110000-564
R33, R344.7kQ, +5%, % W Resistor110000-472

(continued on next page)

5-45

Page 85

Illustrated Parts Lists STAR WARS COCKPIT

Sound PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R35,2.2 kf, +5%, % W Resistor110000-222
R36152, +5%, ' W Resistor110000-150
R3710 kQ, 45%, 4 W Resistor110000-103
R384709, +5%, % W Resistor110000-471
R39, R4012 kQ, £5%, % W Resistor110000-123,
R4168 KO, +5%, 4 W Resistor110000-683
R4212 kQ, +5%, % W Resistor110000-123,
R43,1.5 kQ, +5%, % W Resistor110000-152
R441002, +5%, 4 W Resistor110000-101
R45,470 k0, +5%, & W Resistor110000-474
R46, R4712 kQ, +5%, 4 W Resistor110000-123
R48, R4922 kN, +5%, 4 W Resistor110000-223
R5047k, +5%, 4 W Resistor110000-473
R512.2kQ, +5%, 4 W Resistor110000-222
R52, R5322 kQ, +5%, % W Resistor110000-223
R54, R55,47kQ, +5%, % W Resistor110000-473,
R562.2 kM, +5%, % W Resistor110000-222

Sockets

1c/D28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
1E40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
1F/H24-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C24
1H28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
WK28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
2D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3K40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
4D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
5D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40

Transistors

QI, Q2Type-2N3906 Transistor33-2N3906
Q3, Q4Type-2N3904 Transistor34-2N3904

Miscellaneous

TPI-TPI2Test Point179051-002

5-46

Page 86

STAR WARS Cockpit Ist Printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm O Distributor

Address CO Operator City State Zip O Other

Area Code Phone

Page 87

First Fold

No postage necessary if mailed in the United States

USINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086

Second Fold

28pe spp ade,

Page 88

STAR WARS Cockpit

YOUR COMMENTS, PLEASE! Ist Printing

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm QO Distributor

Address. O Operator City Country O Other.

Phone City Code Country Code

Page 89

First Fold

Atari Ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

wosy,

28po sup ode,

Page 90

BS BES RES HEN BERG HES PRS ERS RH

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays {in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment, None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability account for such products which are shall be, at its option, to repair, replace, or credit Buyer's returned to Seller during said warranty period, provided: {aj Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller’s plant; and

  • Seller's examination of said products discloses to Seiler's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth ina written contract between Seller and Buyer which ay < , i @ x contract supersedes the terms berein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes ror authorizes any otber person to assume for the Seller any otber liabilities in conuection with the sale of products by Seller. Pte ated Nite? Satie ates Nato? Sates Sa

The use of any non-Ataci parts may void your warranty, according to the (erms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 91

ATARI

ATARI, INC. x