CATHODE RAY TOMES

The Ninja Warriors Instruction Manual

The Ninja Warriors (World, later version) (Taito Corporation Japan, 1987) · Instruction Manual · 18 pages · 13 sections · original scan

Page 1

ROMS TAR ‘in

» 0B Romatas Ine: “LicAnsed Nor Tanta Roweica. Curd AN Highs Meanerond ai

(INSTRUCTION MANUAL

Page 2

ME © 1988 Romstar Inc. Licensed from Taito America Corp. All Rights Reserved.

TABLE OF CONTENTS

I. LOCATION AND SETUP..

ll. DIP SWITCH SETTINGS...

HL. ADJUSTMENTS OF TV MONITORG..........::secssessersssensseenssenssaserenenenssnreenenenennnenenenenes 3

A. ADJUSTMENT ON COLOR VIDEO MONITOR 4

B. DETAIL EXPLANATION OF ADJUSTMENTS .. 5

C. CHECK POINTS IN CASE OF DIFFICULTY.

IV. COIN DOOR MAINTENANCE... 7

A. NOTES 8

V. LAYOUTS/MAIN HARNESS PINOUT/FACTORY SETTING.........s::sssssssesssssnencees 9

A. CONNECTOR H/CONNECTOR J/CONNECTOR K.......csscsssssrsssnsrsenssssententonenees 10

C. CABINET DIMENSIONS FOR NINJAWARRIORS ........2s::sssesesscsssssreneeetetenseeenes 12

vil. CONCLUSION

A. LIMITED WARRANTY......:cssssstescsensnenssssescttsstensaccncsssceneatsnsaeecenearseeatentaraeatenserseaness 13

B. FBI WARNING ........sssccssssncsssesnsntensenseensensnescesesepsansnsatenssennescatensnenesanennneneneossasseene 14

C.COMMENTS ......-.scscssescasessetsneseavenenecnsnensenensonsnsestanseacavensasetanensnenuenenesstesnesnenenassenstne 15

Page 3

LOCATION AND SETUP

INSPECTION . Remove the game from its shipping carton. Inspect the entire outside of it for any signs of damage. Any scratches?, dents?, cracks? Any broken controls? Just look it over closely and make a note of any signs of damage. Remove the shipping cleats from the bottom of the cabinet. Install the four levelers, one at each corner of the cabinet. Level the cabinet. Open the cabinet and inspect the inside of the game for any signs of damage. Also check to make sure all plug-in connectors on the wire harness are firmly seated. Replug any connectors found unplugged. DO NOT FORCE PLUGS INTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. Ifit won’tgo on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Makesureall printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. O Note the location of the game’s serial number. O Check all major subassemblies to be sure they are mounted securely. oo9’70f97000nN=

Power supply (s). Control panel (s). T.V. monitor (s). Other P.C.B.’s and/or P.C.B. rack, etc. Power Chassis.

  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up.

-1+

Page 4

DIP SWITCH SETTING DIP SWITCH A THE NINJAWARRIOR

+1273 |/4|/5]6)7]8

CONTINUE MODE Swit Orr

WITHOUT ON 1 COIN- 2 PLAY On lOFE

7 OFF NOT USED ON

TEST MODE nonniNe OFF

TEST MODE ON

DEMO SOUND wr OFF

1 COIN- 1 PLAY OFF] OFF COIN PRICING

  • 2COIN- 1 PLAY OFF| ON COIN SLOT A 2COIN-3 PLAY ON] ON
1COIN- 1 PLAYFF]OF
COIN PRICINGOFF|OFF

1 COIN-2 PLAY ON | OFF

  • 2COIN- 1 PLAY OFF| ON
COIN SLOT B2 COIN - 3 PLAYON|ON
  • ROMSTAR RECOMMENDED SETTING

DIP SWITCH B

DIFFICULTY

NOT USED

NOT USED

DISCOUNT PLAY WHEN CONTINUING WITHOUT

  • ROMSTAR RECOMMENDED SETTING
Page 5

(1)

(2)

(3)

(4)

6)

(6) ADJUSTMENTS OF TV MONITORS

Turn the DIP-SW (A-3) “ON” for the test mode.

When the color-bars appear on the screens, by pressing the 1-P side “DAGGER” button the screens change to the adjusting mode.

In the adjusting mode, each time by pressing the 1-P “DAGGER” button, the background screen changes.

Adjust the monitors whan the screens are in the “city” mode, then make sure the adjustmentis the same in the other modes.

The adjusting-screens do not move. Adjust them so that the standard adjusting-lines will be straight as shown below.

—-— : Line for adjusting HY

(Monitor) | (Monitor) (Monitor)

After finishing the adjustment, when the color-bars appear on the screens, by pressing the 1-P select bution, the screens change to the test mode. If you need the monitor adjustments once more, turn the power switch “OFF” and “ON” again.

“3+

Page 6
NOTE: ADJUSTMENT ON COLOR VIDEO MONITOR

Ome H. WIDTH

H, POSITION | "— RGB-GAIN

H. HOLD BRIGHT H. FREQUENCY” ——————— V. POSITION Vv. HOLD V. LINEARITY

V. HEIGHT

The adjustments have been done at the factory for the best performance, but if necessary, adjust the above pots by referring the explanation for each adjustment.

Careless adjustment will cause failures such as out of synchronization, picture distortion, and highvoltage rising. Never touch the white-paint-locked adjusting devices. Also, extra care must be taken when you adjustthe TV monitor, because higher voltages exist there.

Color distortion may happen depending on the setting condition of the machine. In that case, use a degaussing device or the degaussing switch. Keep magnets away from the screen, or they may result in color distortion.

Page 7

DETAIL EXPLANATION OF ADJUSTMENTS

V. POSITION

For adjusting the vertical raster position.

V. HOLD Use this when the picture moves up or down without stopping. I | |

V. HEIGHT

For adjusting the vertical screen size.

V. LINEARITY

Adjust this Pot, if the upper or the lower part of the screen is shrunken.

H. FREQUENCY

Use this in the case that the adjustment can not be made by using the H. HOLD.

H. HOLD

Use this when horizontal stripes appear on the screen or f

when you want to shift the picture slightly to the left or right.

H. POSITION

For adjusting the horizontal display position of the picture.

H. WIDTH

For adjusting the horizontal screen size.

BRIGHT (for adjusting the screen brightness).

Adjust this depending on the condition in location.

R.G.B. - GAIN R-GAIN . . . for adjusting the red color G-GAIN ... for adjusting the green color B-GAIN .. . for adjusting the blue color

Page 8

CHECKPOINTS IN CASE OF DIFFICULTY

No Raster/No Video . ~ Check A.C. line cord

  • Check line fuse
  • Check monitor brightness ~ Check power switch and/or interlock switch
  • Check all solder connections on line filter and transformer
  • Check for proper orientation of the PCB connector

Raster/No Video

  • Check all PCB to monitor connections ~ Check power supply voltage on PCB

No Video/Game sounds can be heard

  • Check monitor brightness
  • Check all PCB to monitor connections

Wrong colors

  • Monitor needs degaussing
  • Check for proper wiring between PCB and monitor
  • Check monitor adjustment and adjust if necessary

Wavy picture ~ Check monitor ground is properly connected to monitor

  • Be certain sync inputs are properly connected to monitor
  • Check horizontal hold adjustment

Horizontal/Vertical Roll

  • Check horizontal and/or vertical hold adjustments
  • Check for proper wiring of sync from PCB to monitor

No sound

  • Check for -5 volts on edge connector of PCB
  • Check volume control potentiometer adjustment
  • Check for +12 volts on edge connector of PCB ~ Check wiring from PCB to speaker ~ Check speaker for low resistance between the “+” and “-" tabs

Bad sound ~ Check wiring to speaker for bad solder connections

  • Check sound with another speaker

No switch input ~ Check ground connection to switch/es

  • Check wiring between PCB and switch/es for proper connection
  • Check switch/es with an ohmeter to verify proper operation

Switch operates incorrect function

  • Check wiring between PCB and switches for proper orientation
  • Check wiring for shorts between switch inputs

No coin meter ~ Check wiring to coin meter

  • Check that +5 volts is on “+” side of meter
  • Verify a +5 volt meter is used

When coin switch is made and meter pulses, the screen blanks out and/or game resets

  • Verify that a meter with a diode is used ~ If no diode is built in meter a IN4004 can be used across the meter. Cathode to “+” side of meter and anode to “-” side of meter
Page 9

COIN DOOR MAINTENANCE

The magnet that is fitted to the mechanism, should be kept clean from foreign particles. The magnet can be cleaned by swinging the gate open. (as shown in Fig. 1). Remove metal filings from the magnet by guiding the point ofascrewdriver along the edges of the magnet, such that the filings cling to the screwdriver.

The mechanism can be cleaned by immersing in water using a small brush to clean the mechanism. Rinse the mechanism with boiling water and dry with compressed air.

Note: Since the Gold Mech relies on coins passing the magnet at a constant speed, the rejector must be free of dirt and grease which may slow down the coins. Do not lubricate the acceptor with oil as this slows down coins.

If the above procedures are not successful, check for worn, bent or damaged parts and re- Place where necessary. Removal of Mechanism

To remove the coin selector: Unscrew the two screws (as shown in Fig. 2) — swing rear of selector body away from the lock-out side and withdraw.

The Gold Mech Acceptors are designed to tequire a minimum of maintenance and field adjustment. Coins are checked by diameter and thickness, weight, metal content, bounce, and for ferromagnetic coins such as nickel and steel, a rim test also used.

Coin Switch

The coin switch comes in two different spring tensions — identified by the color of the plastic boss at the wire’s pivot point.

Red: Light tension- U.S. 25¢

White: Heavy tension-heavy foreign coins

Page 10

NOTES

Page 11

MAIN HARNESS PIN OUTPUT

  • FACTORY SETTING PLEASE SET THE NINJAWARRIOR PCB AS FOLLOWS: G CONNECTOR ROMSTAR - THE NINJAWARRIORS
WIRE #,WIRE COLORSOLDER SIDECOMPONENTS SIDEWIRE COLOR#

A | B 2

DEAD PINc3DEAD PIN
1BLACKGROUNDD4GROUNDBLACK9
GROUNDE5GROUND
POST (KEY)F6POST (KEY)
H7DEAD PIN
COIN SWITCH BJ8COIN SWITCH AWHITE,10
COIN METER BK9COIN METER ABROWN"1
COINLOCKOUT BL0COIN LOCKOUT A
DEAD PINTILT SWITCHMNSERVICE SWITCHDEAD PIN
2WHITE/GRAYSELECT SWITCH B | N2SELECT SWITCH AGRAY12
3WHITE/RED2 PLAYER UPP31 PLAYER UPRED13
4WHITE/BLUE2 PLAYER DOWNRi41 PLAYER DOWNBLUE14
5WHITE/ORANGE2 PLAYER RIGHTSs51 PLAYER RIGHTORANGE15
6WHITE/VELLOW2 PLAYER LEFTT161 PLAYER LEFTYELLOW16

U 7 Vv 8 [- w | 19

DEAD PINx20DEAD PIN
WHITE/GREEN2PLAYER DAGGER | Y21_'|4 PLAYER DAGGERGREEN17
8WHITE/PURPLE2PLAYERNINJASTAR|= Z22 | 1 PLAYER NINJASTARPURPLE18

DESCRIPTION SETTING ADJUSTMENT POSITION DIP BANK

CONTINUE MODEWITHOFF1A

TEST MODE NORMAL OFF 3 A DEMO SOUND WITH OFF 4 A

COIN A2COIN1 PLAYOFF/ON5/6A
COIN B2COIN1 PLAYOFF/ON7/18A
DIFFICULTYCcOFF/ON1/2B
DISCOUNT PLAYwoOFF7B

WHEN CONTINUING

NOTE: ALL OTHER POSITIONS SHOULD BE OFF.
Page 12

CONNECTOR H CONNECTOR J CONNECTOR K

POSITION | H CONNECTOR ‘WIRE COLOR POSITION J CONNECTOR WIRE COLOR

1GROUNDBLACK1VIDEO R (GROUND)BLACK
2GROUNDBLACK2VIDEO R (SYNC)GRAY
3GROUNDBLACK3VIDEO R (BLUE)BLUE
4GROUNDBLACK4VIDEO R (GREEN)GREEN
5+5 VDCRED5VIDEO R (RED)RED
6+5 VDCRED6VIDEO C (GROUND)BLACK

7 +5 VDC RED [ 7 VIDEO C(SYNC) GRAY

8—5 VDCWHITE,8VIDEO C (BLUE)BLUE
9+12 VDCYELLOW9VIDEO C (GREEN)GREEN
10POSTKEY10VIDEO C (RED)RED

1 VIDEO L (GROUND)

12YELLOWVIDEO L (SYNC)

VIDEO L (BLUE)

VIDEO L (GREEN) VIDEO L (RED)

POSITION | K CONNECTOR WIRE COLOR

SPEAKER R+ WHITE * J CONNECTOR

SPEAKER R—-BLACKVIDEO R= RIGHT VIDEO
SPEAKER L+WHITE/BLACKVIDEOC= CENTER VIDEO
SPEAKERBLACK/WHITEVIDEO L == LEFT VIDEO

olrn]= &

Page 13

AC AND GROUND SIDEWALL DISC PLUG

MARQUEE BLK LIGHTS.

CONTROL PANEL

NY

a |

FAN ON/OFF SWITCH ' a

COIN DOOR

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

FEFHEEFHHHEFHE FH FEE FHF EHH HFEF EHH HEHE HHH HHH et

LIMITED WARRANTY

ROMSTARINC. (‘Seller’), warrants only to the initial purchaser ofits products thatthe items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. Printed Circuit Boards (60) days B. Electronic Components (30) days C. Television Monitors (80) days

No other parts of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from Seller to its authroized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective.

B. Such products are properly packaged and then returned, prepaid to Seller's plant.

This warranty does not apply to any parts damaged during shipping or handling, or due to improper installation or usage, or alteration. Inno event shall Sellerbe liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of Romstar Inc. product.

(WARRANTY DISCLAIMER)

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PHEEH HH EFEFHEHEHE FE FEF ESE EH HFEF EF HEF EF EPH SE HEEHEH HEHEHE HEHEHE HHH tte SHH HFEF HH EHH FH FH HEHE FH HHH HHH EHH HHH HH HEH HEHEHE FH FE HH ES HHH eet

FHEHH HEHE FHF HH FEF H HFEF HFS HHH HHH HEH HH HHH eee 13.

Page 16

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

“145

Page 17

COMMENTS:

Your comments will assist Romstar Inc. in improving our product. Your comments are an important part of preparing new games/manuals.

If you have any technical questions regarding our games or are requesting additional information, please contact our Customer Service Department.

Fill in if you wish a reply:

Name

Firm O Distributor

Address O Operator

City State Zip O Other

Area Code Phone

Page 18

ROMSTAR ‘inc.

ROMSTAR INC. 22857 Lockness Avenue Torrance, CA 905041