CATHODE RAY TOMES

Tempest Cocktail TM-193 1st Printing

Tempest (rev 3, Revised Hardware) (Atari, 1980) · Technical Manual · 64 pages · 63 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION Your game's serial number is stamped on a label on the outside of the game. The same number is also stamped on the chassis of the video display, Regulator/- Audio || PCB, and the Tempest™ Analog Vector-Generator PCB and Auxiliary PCB. Please mention this number whenever calling your distributor for service.

VIDEO DISPLAY

REGULATORI/AUDIO II PCB

POWER SUPPLY

GAME SERIAL NUMBER \DENTIFICATION TAG

AUXILIARY PCB

ANALOG VECTOR- GENERATOR PCB ee ee

Page 3

Introducing Atari’s First Color X-Y Video Game...

Cocktail Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists N

Page 4

Tempest ™/Cocktail

Copyright © 1981 by Atari,Inc. —_ All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording. nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Tempest™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, the display manual, and the troubleshooting guide are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound Infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay cosis and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use ali legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases. such copies risks forfeiting such a game.

Published by: ATARI INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A. 11K

Page 5

Tempest™/Cocktail

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.'s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari paris in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Tempest ™/Cocktail

Table of Contents

1 Set-Up Procedures pompPr

omm New Features... .. Opening the Game Cabinet Game Inspection ..... Game Installation. .

  • Voltage Selection....
  • Interlock and Power On Adjusting the Table Legs........... Self-Test Procedure ... Option Switch Settings . .
  • Bonus Play Feature......
  • Coin Mechanism Multiplier:
  • Examples of Game Price Settings . Game Play
  • Attract Mode ........
  • Ready-to-Play Mode
  • PlayMode ....-..... :
  • High Score Initial Mode 2.0.0... 0... cece cee eee eee N®OOMTDRNDNHNASNOMTER ER WWW

Maintenance and Repair A. B. Cleaning ©... cece eee eee eens Fuse Replacement . The Control Panei....... .

  • Leaf Switch Replacement....... 0.0.0.0 cece ee cee ee 21
  • LED Start-Switch Replacement .............-.. 0. ccc ee eee eee ee 21
  • Encoder Wheel Maintenance and Repair Video Display Removal ............. Printed-Circuit Board Removal ...........- 0... e cece cece eee 24
  • Game PCB Removal ......--. 0. cece cece eee eee nee eens 24
  • Regulator/Audio Il PCB Removal . Speaker and Fan Removal ..... Game Operation... 2.0.00... ccc cece eee tenet eens 27

3 Illustrated Parts Lists illustrations and parts lists begin on page .............0.- 002s e eee 29

Page 7

Tempest Cocktail

List of Illustrations

Figure 1 Overview of Game ... 2 Figure 2 Installation Requirements . . 4 Figure 3 International Voltage Plug Selection . : 4 Figure 4 Interlock and Power On/Off Switches ............ 2.000 e eee e eee eee 5

Figure 5 Adjusting the Table Legs... 6.0.20... 0 sce cece cece eee eee 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches ... 7 Figure 7 Self-Test Procedure . 8 Figure 8 Game Option Settings 11

Figure 9 Game Price Settings Figure 10 Coin Counter Option Settings . 14 Figure 11. Opening the Control Panel and Replacing Switches . 20 Figure 12 Control Panel Witing ...... 2.2.0... cece cece cece cece tenes 21

Figure 13 Encoder Wheel Maintenance and Repair Figure 14 Video Display Removal.......... Figure 15 — Printed-Circuit Board Removal see . Figure 16 Speaker and Fan Removal ......... 6.000 cece eee eee eee tees

Figure 17 Power Distribution ...... 2.00.60. e ccc cece een eae 27 Figure 18 Signal Distribution ........ 06... e cece center nee 28

Illustrated Parts Lists: Figure 19 Cabinet-Mounted Assemblies ........... 00... c cece eee ene eee 30 Figure 20 Control Panel Assembly Figure 21. Encoder Wheel Assembly .... Figure 22 Regulator/Audio Il PCB Assembly .......... 000.0 c eee eee eee 37 Figure 23. Tempest™Auxiliary PCB Assembly .......... 00.0000 cece eee eee 39 Figure 24 Tempest™Analog Vector-Generator PCB Assembly Figure 25 Shielded Color X-Y Power Supply Assembly .... Figure 26 Vertical-Mounted Coin Door ......... 00... eee cee eee cee 48

Page 8

Tempest ™iCocktail

NOTE If reading through this manuai does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) z From California, Alaska or Hawaii (408) 745-2900 age From anywhere else in this area © joitfree (800) 536-1611

EAST U.S.A. Game sales and service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey Zs (201) 469-5993 s From anywhere else in this area foll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland \RELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)

@ 0062-52155

vi

Page 9

Set-Up

Procedures

Introduction

This manual, written for game operators and service technicians, describes the Tempest™/Cocktail game. Chapter One explains new game features, game set-up, self-test procedures, option switch settings and game play. Chapter Two consists of maintenance and repair information. Chapter Three contains illustrated parts lists.

Page 10

Tempest™/Cocktail

Fl TABLE TOP

é Ww MS

COLOR XY SipPOnE AEM VIDEO DISPLAY

i! AUXILIARY PCB

ANALOG VECTOR- | GENERATOR PCB

CONTROL PANEL

ENCODER-WHEEL CONTROL REGULATOR!

‘AUDIO PCB

ACCESS PANEL ;

UTILITY COIN SWITCH, SPEAKER SELF-TEST SWITCH, & VOLUME CONTROL

COIN COUNTER

POWER SUPPLY

COIN DOOR

ADJUSTABLE LEG

Figure 1 Overview of Game

Page 11

A. New Features

The Tempest™/Cocktail game has five new features. Even if you are familiar with Atari games, you should note these important differences. The new features are: @ Color X-Y Video Display and Game Printed-Circuit Boards (PCBs). Tempest is Atari’s first color XY game. The color XY video display produces a great number of colors in varying intensities. Atari's XY game circuitry has been redesigned for a color video display. @ Game Play. Atari introduces Skil-Step™, and 99 levels of play on 16 different piayfields. A demonstration mode allows you to accelerate through 98 jevels of play. In addition, a special switch setting lets you freeze the game action (see Section H, Game Play). @ Encoder Wheel. This new control has a compact, simplified design which makes servicing easy. This control's circuitry is contained on a single PCB. The very smooth action is designed for greater player accuracy. @ Coin Door. This game has Atari’s new verticalmounted coin door. It allows full access for servicing the coin acceptors and other electrical parts, yet provides security for the cash. Therefore, the two doors are separately keyed. @ Cabinet Design. This newly designed cocktail Cabinet places most of the game components in one compartment. The Analog Vector-Generator (AVG) and Auxiliary PCBs are mounted back-t back and separated by plastic standoffs. In ad tion, the adjustable legs provide cabinet stability with two cocktail-table height settings and a third setting which allows a player to stand while playing the game. These new features, as well as other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol: “es

WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded! Tempest ™/Cocktail

B. Opening the Game Cabinet

1.

e

2.

3. °

Opening the Table Top

To open the game cabinet, unlock and open the coin door. Reach inside and open the luggagestyle latch located on the cabinet wall to your right. Next, unlock the lock at one end of the game, located immediately below the table top (see Figure 1). Carefully {ift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing.

Access Panel To remove the access panel, unlock it and pull it away from the game cabinet.

Closing the Table Top

To close the cabinet, stand opposite the hinged end of the cabinet and grasp the table top with your right hand. With your left hand, press the button at the middie of the support arm and puil the support arm out towards the left. Gently lower the table top to the closed position. Lock the key lock. Then reach inside the coin door and close the luggage-style latch. Lock the coin door.

C. Game Inspection

Please inspect your game carefully to insure that it was delivered to you in good condition.

NOTE Do not plug the game in ye

. Examine the exterior of the game cabinet for dents, chips, or broken parts. Unlock and open the table top and access panel; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty.

Page 12

Tempest™/Cocktail

@ Check that all plug-in integrated circuits on the game PCBs are firmly seated in their sockets. @ Check that the plastic standoffs are in place, holding the PCBs away from each other. @ Check the power cord for any cuts or dents in the insulation.

WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the video display with your hands or with metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label under the contro! panel on the outside of the game cabinet. Verify that the serial numbers on the Tempest™ Analog Vector-Generator PCB, Tempest Auxiliary PCB, Regulator/Audio II PCB, power supply and video display are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power Supply, control panel and video display for secure mounting.

D. Game Installation

Figure 2 Installation Requirements

Power 250 watts maximum Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 72 x 95 cm (28% x 37 V2 in.) Game Height 68 to 104 cm (27 to 41 in.)

  • Voltage Selection The power Supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with one, two or three colored voltage selection plugs.

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120)* Yellow* 200-240 VAC (220) Blue 220-260 VAC (240) “This is the only plug provided on the North American power supply. Brown

Figure 3

WARNING

Fuse cover must be in place during game operation.

International Voltage Plug Selection

Page 13

SAFETY INTERLOCK SWITCH

Figure 4

Before plugging in your game, make sure that the voltage selection plug(s) on the power supply is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.

  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located under the table top and the other is behind the access panel. This switch removes all AC line power from the game circuitry when the panel is opened. Check for proper operation of the interlock switch by performing the following steps: @ Be sure the table top and access panel are closed. Tempest™/Cocktail

SAFETY INTERLOCK SWITCH

SWITCH COVER

POWER ON/OFF SWITCH (Reach under game to activate switch)

Interlock and Power On/Off Switches

@ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the “on” position. Within 30 seconds the video display should display a picture. @ Slowly open the table top. The video display picture should disappear when the top is lifted approximately 2/2 cm (1 inch). Close and lock the table top. @ Slowly open the access panel. The video display picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock this panel. @ If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the video display picture doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.

Page 14

Tempest ™/Cocktail

  • Remove or empty the coin box. Loose coins may slide out of the coin box and in- REMOVE COIN BOX to the game cabinet. K> * Lay the table on its side. Place a support (the coin box, books or tool box) under the pi recessed side of the cabinet. Loosen the two Allen-head screws on each leg. Grasp the legs and slide them into the desired position. Then tighten the screws.

USE TWO SCREWS WHEN ATTACHING EACH TABLE LEG!

SAK in. 29%, in. = SHIPPING POSITION (26% in.)

Figure 5 Adjusting the Table Legs

E. Adjusting the Table Legs NOTE

To ensure cabinet strength, you must use two screws when attaching each table This cocktail-table game is designed for four ad- leg. Using only one screw may result in justable heights—68, 74, 80 or 104 cm (27, 29%, 31%. damage to the cabinet wal! when you or 41 inches). To adjust the table height, refer to move the cabinet across the floor. Figure 5.

Page 15

F. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the video display and the game speaker; no additional equipment is necessary. Tempest ™/Cocktail

Part 1 of the self-test procedure includes a display of the operator-selectable game options, and game time and high score table information. Part 2 includes ROM and RAM, control panel and display information. We suggest you run the self-test procedure any time you collect money from the game or any time you change the game's options. Refer to Figure 6 for location of the self-test switch and option switches. To run the self-test, follow the instructions outlined in Figure 7.

VOLUME INCREASE: TURN CLOCKWISE

SELF-TEST SWITCH

UTILITY COIN SWITCH AUXILIARY PCB

ANALOG VECTOR. GENERATOR PCB

Figure 6 Location of Self-Test Switch,

Volume Control and Option Switches

Page 16

Tempest™/Cocktail

Figure 7 Self-Test Procedure Part 1

The information below is displayed on the screen if you set the seli-test switch to on during the attract mode. Look at the displayed numbers for SECONDS ON and SECONDS PLAYED. If these numbers run together vertically, make adjustments to the X-BIP and Y-BIP potentiometers on the game PCB. To go to Self-Test Part 2, rotate the control knob until the message PRESS FIRE AND ZAP FOR SELF-TEST appears on the video display. Then press both FIRE and SUPERZAP. To end the operator information display, set self-test switch to oft.

TIME GAME ON (Seconds) P FOR SELF TEST PRESS FIRE AND ZAP FOR SE TIME GAME

1 "ae FARE ON PLAYED (Seconds) i te a seU GAM

7 te(RERBRE1-PLAYERGAMES

NO. OF

COIN MECHan2-PLAYER GAMES

MULTIPLIER [= ADDER AVERAGE

SWITCH AT N13 ——— “LS GAME TIME

(Coin Modes) UOGOMOOC-—___|_~eewws ADDER

SWITCHOOO00000eet

TOGGLE ooog0000 SWITCH AT 112

(Game Play)OO repSWITCH AT DIEZ

LIVES (Game Difticulty)

PER GAME

CMLXXX ATAR:GAME
stale SveeysachaDIFFICULTY

SOIN MEY Z _ 7 <——— coin move

NO. OF ae LANGUAGE

CREDITS (English)

Operator Information Display

To erase High Score Table:

  • Tur control knob until top line reads PRESS FIRE AND START 2 TO ZERO SCORES. Press both FIRE and START 2. The word ERASING appears and blinks on the screen untii the entire table is erased. Wait until the word ERASING disappears before continuing with other tests. 2. 3. To erase Game Times:
  • Turn control knob until top line reads PRESS FIRE AND START 1 TO ZERO TIMES. Press both FIRE and START 1. The word ERASING appears and blinks on the screen until the entire table is erased, Wait until the word ERASING disappears before continuing with other tests. 2. 3.

[Seif-test is continued on next page]

Page 17

Tempest™/Cocktail

Figure 7 Self-Test Procedure Part 2

Instruction Test Passes

Test Fails

After about 5 seconds, the video displays the picture below. No sounds are

  • Set self-test switch to on. Press RESET on the PCB, or turn power off RAM FAILURE is indicated by a sequence of 1 to 12 tones and an A displayed in top half of screen. You will hear a short low tone and see a short flash on the LED start Pushbutton for each good RAM chip, and a long high tone accompanied by a long pulse on the start pushbutton for a failing RAM chip. The test stops with the first failand on again. produced. ing RAM. To restart the sequence, press RESET on the PCB, or power game to off, then to on again. Identify the bad RAM chip with the table below. Example: four short low tones followed by a long high tone indicates failure of RAM at location M3.

AUDIO 1 1S BAD ENTIRE WHITE FRAME Bad RAM Chip Location VISIBLE AND WITHIN Long High Tone ‘on Analog Vector-Gen’r. PCB ROM AT Ri Ye

Ls ohoYsINCH OF VIDEO DISPLAY EDGEistFa

2nd

Xx3rdRa

4th P4

TOGGLE Sth M3

TOGGLE‘SWITCH 86thMa
SWITCH 17thB
ockTaiL|—SWITCH AT L128thLa
beevitisreeAponoogr(Game Play)oth8
SWITCH AT N13 Seee—— faunelbin alt)iin3
(Coin Modes)(GameDifficulty)11th33
START 2ABAOONCONTROLjth4

START 1

FIRE LEFT COIN MECH SUPERZAP UTILITY COIN SWITCH

SLAM SWITCH

PHOTO ABOVE SHOWS AN EXAMPLE ONLY

NOTE Press Start 1: Screen flips to player 1 and readout is for player 1 control switches. Press Start 2: Screen flips to player 2 and readout is for player 2 control switches. RIGHT COIN MECH

ROM FAILURE is indicated by a vertical pair of hexadecimal numbers on the top of the screen. The top number indicates the location of the failing ROM(s). Ignore the bottom hexadecimal number in the pair. Identify the bad ROM with the table immediately below.

Displayed No. PCB Location Bad ROM Chip Location Rt Pt MIN1 uM1 Analog Vector- Ki Generator PCB a H1 Ft et D1 R3 NIP3* CANARD OVLEPODD

EAROM, Audio and Math Box Failure are indicated by a single letter in the center of the display. Identify the failure with the table below.

Displayed Letter Failure PCB Location

EEAROMC3 (Aux. PCB)
PAudio 1B/C2 (Aux. PCB)
QAudio 2CID2 (Aux. PCB)

R RAM See RAM test above M Math Box**

  • It this ROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **Math-box failure is explained in TM-195, Tempest Troubleshocting Guide.

[Self-test is continued on next page]

Page 18

Tempest ™/Corktail

Instruction Figure 7 Self-Test Procedure Part 2, continued

Test Passes Test Fails

  • Activate start, fire, Superzap, SLAM, and coin switches. *
  • Rotate encoder wheel clockwise and counterctockwise.

4 Observe the white frame around the outside of the screen.

  • Activate SLAM switch.
  • Activate SLAM switch.
  • Activate SLAM switch,
  • Activate SLAM switch.
  • Activate SLAM switch.
  • When satisfied with test, set selttest switch to off position. As switch activates, you'll hear a beep and Q changes to 1 on the screen.

The right hexadecimal number on the screen will increase with counter clockwise motion, and decrease with clockwise motion.

Each frame corner should be within Y2-inch of each video display bezel corner.

A white cross hatch pattern appears. A character set appears at the bottom of the screen.

Horizontal and vertical lines cross in the center of the screen dis: playing a large “plus” sign. Audio 0 1 and 2 alternate to produce four tones.

Tests purple, cyan, yellow, white, green, blue, and red for color and intensity. Displays ‘seven groups of vertical lines, each with right line the brightest and left line the dimmest.

A checkerboard pattern touches the sides and corners of the video display. Rotate the contro! knob to change color.

Awhite frame is dis- Played on the screen. You will not hear a beep and 0 will remain on the screen for the defective switch.

Incorrect progression of numbers indicates encoder wheel harness wires were connected incorrectly. No number change indicates encoder wheel is bad or harness. wires are loose.

Consult Tempest™ Drawing Package to adjust video pots.

If display is not centered and symmetrical on the video display, adjust video pots (see Tempest Drawing Package) on the main PCB. If character set is incorrect, check Vector ROMs (see Troubleshooting Guide).

No sound indicates failure of an audio amplifier and/or the custom audio chip(s).

Use this pattern for tracking adjustments (see the Color X-Y Display Manual).

Use this pattern for purity and convergence adjustments (see Color X-Y Display Manual).

  • Activate coin switches by inserting at least one coin in each coin slot. You will net trip the coin counters as long as you are in self-test.
Page 19

G. Option Switch Settings

  • Bonus Play Feature Tempest™/Cocktail offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to Offer it or not. Tempest ™/Cocktail

Figures 8, 9 and 10 provide “$” symbols indicating Atari’s recommended settings. All toggles are preset in the “on” position as per these recommendations. However, you may change the settings to suit your individual needs.

With your game set at 25¢ per play, players who deposit four successive quarters, then press the start button, can receive a bonus play. Therefore, players can receive 5 plays for $1.00.

Figure 8 Game Option Settings To change ioggle positions on the switch assemblies, you need not remove the game PCB. The switches are accessible when the Tempest™ Analog Vector-Generator PCB is mounted in place. To change positions on the Auxiliary PCB you need to remove both PCBs from the game. When changing the options, verify proper results on the video display by performing the self-test. Note that changing an option ‘on any of the following eight toggles will not cause an immediate change on the video display screen during the attract mode.

Settings of 8-Toggle Switch on Tempest Analog Vector-Generator PCB (at L12) 1 2 4 5 6 7 8 Option

On On On Off

Off On

Off Off

On On Off On Off On

On On On

On Off Off Off On On

Off On Off

Off Off On

Off Off Off Off Off On On On Off Oft On Settings of 4Toggle Switch on Auxiliary PCB (at D/E2).

Off Off Oft On On Off On On

3 ott

On On 1-credit minimum $ Off 2-credit minimum English $ French German Spanish Bonus life granted at every: 10,000 points 20,000 points $ 30,000 points 40,000 points 50,006 points 60,000 points 70,000 points No bonus life

2 lives per game Silives pergame $ 4 lives per game 5 lives per game

Game difficulty” Medium $ Easy Hard Medium

Starting Level: 1,3,5,70r9 $ 1, 3,5, 7, 9or 11 if current high score 300,000-499,999 1, 3, 5, 7,9, 11 or 13 if current high score 500,000-699,999 1, 3,5, 7,9, 11, 13 or 15 if current high score more than 700,000

$ Manufacturer's suggested settings *Easy—Enemies move slower and one less enemy shot on the screen at one time. Hard—One more enemy, enemies move faster and 1-4 more enemy shots on the screen at one time. For pricing for “credits,” see Figure 9. Changing toggles 1-5 erases the high score table.

a

Page 20

Tempest™/Cocktail

This bonus feature encourages players to insert more money than just the minimum 25¢ required for one game. Various other bonuses are also available (see Figure 9).

  • Coin Mechanism Multipliers This game has a new vertical-mounted coin door with a separate coin-box entrance; it has two mechanisms. The Tempest™ game PCBs identify the differeni coin mechanisms in a certain pattern.

The basic unit of measurement is 25¢ or 1 DM, which equals a multiplier of x1. Therefore, if you have a 2 DM/1DM coin door, you will probably want to set the left and right option-switch multipliers at x2ix1.

Figure 9 Game The table below contains the switch settings for options relating to game price, coin mechanism multipliers (German coin doors), bonus play, demonstration and freeze mode.

The Demonstration Mode allows you to choose any ievel (1-81) in the ready-to-play mode and accelerate through as many as 99 levels without having to kill the enemies. The Demonstration- Freeze Mode** allows you to stop the action. The score is zeroed at the end of the game in this mode. You can set these multipliers with toggles 4 through 6 on the Tempest™ Analog Vector-Generator PCB switch assembly at location N13. For exact settings of these toggles, refer to Figure 9.

  • Examples of Game

Price Settings

Figure 9 explains the game price settings, giving six examples of the most common U.S. situations. The toggles mentioned in Figure 9 are all in the switch at location N13; they only relate to game price, coin mech multipliers, and bonus plays.

Set the toggles per the table below for the Demonstration Mode. Next, rotate the control knob. You may choose level 1 through 81 during the ready-to-play mode. Press either START button to accelerate through the tubes. Press the FIRE button to clear the spikes at the bottom of the tube. To freeze play, set switch 1 to off.

Toggle Settings of 8-Toggle Switch on Tempest ‘Analog Vector-Generator PCB (at N13) 1 2 3 4 5 6 7 Option

Off Off On On

On On Off Off On Off On Off

On Off

On

On

Off

Off

On

On On

Off

On

Off

On

Off On Off On Off Free play 1 coin* for 2 credits 1 coin* for 1 credit $ 2 coins* for 1 credit

Right coin mech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coin mech x 1 $ Left coin mech x 2

No bonus coins $

For every 2 coins inserted, game logic adds 1 more coin* For every 4 coins inserted, game logic adds 1 more coin*

For every 4 coins inserted, game logic adds 2 more coins* For every 5 coins inserted, game logic adds 1 more coin* For every 3 coins inserted, game logic adds 1 more coin*

Demonstration and Freeze Mode** in”. \) On Off Off Off Off Off On On Demonstration Mode Demonstration-Freeze Mode

$ Manufacturer’s suggested settings

  • In the U.S. a “coin” is defined as 25¢. In Germany a “coin” is 1 DM. ** If you press RESET during this mode, game will lock up. To recover, set switch 1 to on. To achieve bonus plays, all coins must be inserted before pressing Start button.
Page 21

Tempest™/Cocktail

Figure 9 Game Price Settings, continued

The white block below contains Atari's suggested settings. Ail Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation (labels are below). Use the label no. 6 (incation N13, on the Tempest™ Analog Vector-Generator PCB, dicated with®) only if you set toggle 8 at PCB switch assembly L12 to off.

50¢ PER CREDIT: Bonus Bonus $.75 = 2 plays No bonus $1.00 = 3 plays $1.00 = 3 plays

25¢/25¢ Mechanisms

25¢ PER CREDIT:

Bonus Bonus

No bonus $.50 = 3 piays $1.00 5 plays

123«4
25¢/25¢2)OnOnOnOn
Mechanisms©5678
OnOnOnOn

Game Pricing Labels: Ke @@ 2 coins 8! @@@ 3 coins @0@@ 4 coins

° @@ 2 coins = 1 play A @ $1 coin = 3 plays (Susan B. Anthony coin) oe J, @®@ 2 coins =1 play ATARI

oo, @ 1 coin = 1 play anal 2 play minimum (2 coins = 2 plays) eo JK @ 1 coin = 1 play ATARt

KO @ @ 2 coins = 1 play ATARI 6 ee @ 4 coins = 3 plays

oe (For operator use—write in

Ak the appropriate phrase. Use

|. @ permanent-ink water-resis- ATARI tant marker)

Page 22

Tempest ™/Cocktail

Figure 10 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4Toggle Switch on Analog Vector-Generator PCB (K10/11) Two coin acceptors

4321in the coin door:
OnOffBoth acceptors activate all coin count-

ers simultaneously.

RROffOnBoth acceptors activate 2 counters
88separately. $$
22OffOffBoth acceptors activate 2 counters

separately.

OnOnBoth acceptors activate all coin count-

ers simultaneously. $

$ Manufacturer's suggested settings for games with one coin counter. $$ Manufacturer's suggested settings for games with two coin counters.

H. Game Play ws

Atari’s Tempest™/Cocktail game is a one- or twoplayer game with a color X-Y or vector-generator video display. This new display, with its 3-color guns and higher voltage, has the same technology that was used in Atari's black-and-white X-Y displays. However, the screen now displays dazzling color and unique visual effects in a spectacular three-dimensional video display.

Tempest™/Cocktail introduces additional new features: ®@ Skill-Step™ with 99 skill levels of play ® Operator-information display @ Demonstration mode with freeze

Skill-Step™ allows a player to start a game at the same level as was previously achieved (he must start the next game within 30 seconds), without having to start over at the beginning levels. Therefore, skillful players continue to be challenged while less experienced players try to master higher levels. The 99 skill levels of play include 16 different playfields and 6 different targets.

The Operator- Information Display is a special sequence in the self-test mode displaying game-time information: number of seconds the game has been on and been played and the average game time. This display lists the number of one- and two-player games played, option switch settings, number of lives, level of difficulty, bonus levels, credits, and game pricing information. In this mode, you may clear the special “permanent” memory by erasing the high-score table or game-time information. The word ERASING appears on the screen during either of these processes.

The Demonstration Mode allows you to accelerate through 98 tubes by blasting down the tube toward the far rim without having to kill the enemies. Also, you can freeze game action so you can enjoy the dazzling effects of your journey through the tubes.

In addition to these new features, Tempest™/- Cocktail has five possible modes of operation: attract, ready-to-play, play, high score initial and selftest. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (if you enter Part 1 all credits are retained; enter Part 2 and all credits are cancelled). Wait at least eight seconds after a game has been played before entering self-test or turning off the power. Otherwise, you may erase the high score table.

Page 23
  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when in self-test. In the attract mode, the video displays one of three possible pictures.

One of the pictures is the high score display which lasts for 12 seconds. The score(s) from the last game is at the top of the screen. Following is the highest score and player's initials. The top eight scores and their matching initials appear in the center of the screen. The ranking (from 1 to 99) for the last player(s) appears under the high score table.

© MCMLXXx ATARI appears three lines from the bottom of the screen. Next, if the 2-game option is selected, BONUS EVERY 20,000 alternates with 2 CREDIT MINIMUM. Credits and game price appear on the bottom line of the screen.

Finally, at the top of the screen, the words /N- SERT COINS and GAME OVER alternate if there are no game credits. The words PRESS START and GAME OVER alternate if there are game credits.

A second picture, lasting for 12 seconds, is the TEMPEST logo. In this sequence, a multicolored square shrinks toward ihe center of the screen where a very small TEMPEST logo appears. The word TEMPEST enlarges in multiple images and changes color. In addition, © MCMLXXX ATARI appears on the lower half of the screen. Tempest™ Cocktail

The next picture, lasting from 5 to 60 seconds, shows the last game score, the highest score and its initials, and the words PRESS START or INSERT COINS alternating with GAME OVER at the top of the screen. Credits, game price, and bonus-life information are at the bottom of the screen. In the center of the screen, the picture duplicates a typical game-play sequence with the computer controlling the shooter.

The shooter rotates on the end of the tubelike surface that is nearest to the player. Enemies land on the end of the tube that is farthest away from the player and climb toward the shooter. The shooter fires down the tube at the approaching enemies. This scene ends when either the shooter gets shot or spiked or when the shooter kills all the enemies and blasts through the tube into space and lands on the next playfield.

If a player has credits and spins the control-panel knob, the attract mode ends and the words PRESS START appear in the center of the screen. Above this is the score from the last game and the highest score and its initials. Below the words PRESS START are credits, game price and bonus life information.

If you select the 2-credit minimum option and a player inserts enough money for one credit, the messages /NSERT COINS and 2 CREDIT MINIMUM appear in the center of the screen until sufficient coins are inserted for game play.

ale)

Page 24

Tempest™/Cocktail

2. Ready-to-Play Mode Qi)

This mode begins when sufficient coins are accepted for a game. Each player rates himself by rotating the control knob. The knob moves a square which frames the level he wishes to select. The surface shape and bonus points for that level are also shown on the screen.

Bonus point incentive encourages play at a higher level, once that level has been reached. For example, starting at Jevel one and playing through level nine awards 34,000 points. Starting at level nine and playing through that level awards 59,009 points. If a player reaches a higher level, he may continue to play near that level by pressing start before the attract mode is over. For example, if a player ended his last game in level 20, he may choose level 1, 3, 5, 7, 9, 11, 13, 15, or 17.

The ready-to-play mode ends when any pushbutton is pressed or 10 seconds elapse.

  • Play Mode

In the play mode, a player-controlled, yellow clawlike shooter moves around on a three-dimensional tubelike playfield. The shooter rotates on the end of the tube that is nearest to the player. Enemies land on the end of the tube that is farthest away from the player to climb toward and attack the shooter. The shooter fires down the tube at the approaching enemies. When a player kills all the enemies on a tube, he blasts through the tube, flies through space, lands on a new tubelike playfield, and fights the enemies on that playfield. A player scores points by shooting enemies and by blasting through the tube to a new level. The player loses a life when killed by the enemy. The game is over when ail the player's lives are gone.

All action occurs on one of sixteen suspended tubelike playfields. The three-dimensional tube surfaces are viewed from the top, so the view of the first playfield (a circle) is like looking into a well. Each playfield is made of 16 rails which connect the nearest to the farthest rim. The playfield color changes every 16 levels: level 1 is blue, level 17-red, level 33-yellow, level 49-cyan, 65-/nvisible and 81-green.

In addition, other events cause playfield color variation. The shooter causes the two rails on which it sits to change color. Superzap causes the playfield to flash as enemies are zapped. Playfield rails flash rainbow colors when a player earns a bonus life. Pulsar enemies cause sections of the nearest rim to disappear, and during the pulse phase, adjacent rails to flash.

The player's shooter is controlled by rotating the control-panel knob. The shooter moves around on the nearest rim of the tubelike playfield. The ends of the shooter always touch two adjacent rails. The rails on which the shooter sit change color (yellow in levels 1-16) which gives a flashlight effect and helps the player see the enemies in his lane.

A player shoots by pressing the fire button: tap it for one or two shots or press it for all eight shots. A shot is extinguished when it hits an enemy, after it passes the far rim or after it plows a certain distance into an enemy spike. A shot is renewed after it is extinguished so there may be a maximum of eight shots on the screen at one time.

Page 25

A player may use two superzaps per level. A first superzap kills all enemies on the playfield at the time of firing. A second superzap randomly kills one enemy on the playfield. The superzap does not affect enemy shots, spikes or enemies not yet landed on the playfield. Superzap is recharged when the player blasts to a new level.

The following hints will help in game play: @ Players should work their way up through the levels to become familiar with game play. Drop down a level if play is too difficult. @ Experienced players should start at highest level possible for maximum points. @ On anew playfield shoot at enemy dots at far rim. @ Shoot the flipper at the top as soon as it starts to flip. @ Use long spikes to reclaim shots and kill enemies (at the top) approaching you from adjacent lanes. @ Avoid shooting fuseball-tankers near the top, since emerging fuseballs usually zip up to the top and kill you. Tempest™/Cocktail

@ Use Superzap right before last enemy reaches the top for a few extra points.

  • High Score Initial Mode This mode begins when a player has one of the eight top scores. First, there is a fireworks display. Next, the high score table appears. Finally, a player enters his initials directly into the table following the instructions at the bottom of the screen. The initials and score are highlighted in a special color. You may bypass this mode by pressing the start button.

All but the three highest scores are erased whenever you enter the self-test mode, or press the RE- SET button on the game PCB, or turn off the power. This resetting replaces the five lowest scores with fictitious scores and initials.

\f you change game options, lives per game, bonus level or difficulty, or if you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and initials. Therefore, the table will always be displayed on the screen, possibly consisting of one or more real scores and players’ initials.

Enemies in the Tempest”! Cocktail Game

Enemy Description

First Level Appears Points for Kill

Flipper ~s_ PK

Tanker

Spiker

Spike

Fuseball

Pulsar vw Originates at far rim and rides up two rails. Flips in the tube and on near rim. Kills player by flipping onto shooter or by shooting him. Player kills flipper by shooting when it is in the tube or when it is “standing” up. Or use Superzap. Originates at far rim or from a spiker. Rides between rails. Carries one or two flippers, fusebatls, or pulsars and expels these when shot or near rim. Kills player by shooting him. Player kills by shooting tanker in the tube. Or use Superzap. Originates at far rim. Rides up between rails on spike which it builds. Kills player by shooting him. Player kills by shooting it. Or use Superzap. Originates at far rim and builds up toward near rim. Kills player on contact. Player kills by shooting one or more times. Originates at far rim or from Tanker. Quickly rides on one rail, jumps to next rail and seeks out shooter. Kills player on contact. Player kills by shooting when fusebail is jumping between rails. Or use Superzap. Originates at far rim or from Tanker. Rides up and down ‘on two rails. Flips in the tube and on near rim and seeks out shooter. Kills if player is on same rails when it pulses, flips onto or shoots player. Player kills by shooting pulsar in the tube. Or use Superzap.

ard

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

Maintenance and Kepair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if the encoder wheel, light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts—or lubricate the encoder wheel: for details see this chapter.

Page 28

Tempest™/Cocktail

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

The large table top is made of tempered glass and should be scratch-resistant. If cleaned without abrasive substances, you should hardly ever have to replace it.

B. Fuse Keplacement

This game contains six fuses—ali on the power supply assembly (not including the video display fuses). Replace fuses only with the same type as listed in Figure 25 of this manual. See the color XY display manual, TM-183, for the display fuse data.

C. The Control Panel

Prior to repairing or replacing any switch or the encoder wheel on the contro! panel, unplug the game. Next, open the game top as described in Chapter 1, Section B, Opening the Game Cabinet.

Remove the two sets of button-head screws and lock washers at the top edge of the control panel. Once this hardware is removed, tilt the control panel toward you.

After servicing the start switches or any components on the control panels, be sure you reconnect the harness wires to the proper termination points, as shown in Figure 12.

COMMON CONTACT LIGHT-EMITTING-DIODE -E.D.) CONTACTS wi NORMALLY OPEN Ex ~~~. (N.0.) CONTACT

NORMALLY CLOSED (N.C.) CONTACT

To Remove LED Switch: @ Remove all wires from the faulty switch. Turn the switch counterclockwise while holding the black cone-shaped bezel on the outside of the control panel. ® Install a new switch using the reverse procedure. @ Reconnect the harness wires.

CAUTION Players may receive an electric shock if this control panel is not properly ground. ed! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

Figure 11 Opening the Control Panel and Replacing Switches

Page 29

Tempest™/Cocktail

1-PLAYER START SWITCH: ENCODER WHEEL PCB:

BLACK BLUE, RED, BLACK

RED & VIOLET WIRES ——————— WHITEIBLACK STRIPE WHITE

2-PLAYER START SWITCH: RED

BLACK ZAP SWITCH:

BLACK AND YELLOW, BROWN

FIRE SWITCH: BLACK AND ORANGE

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the green ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

Figure 12 Control Panel Wiring

  • Leaf Switch Replacement
NOTE Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

The leaf switches operate on 5 voits at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is very high-humidity.

Don’t burnish the switch contacts. To clean the cross-bar contacts, wipe them with a non-abrasive surface. A business card works very well.

To replace a leaf switch, remove the screw with a Phillips-head screwdriver .

\f the black button needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the contro! panel. The black ring on the outside of the contro! panel should not spin, due to its design.

  • LED Start-Switch Replacement The light-emitting diode (LED) switches near the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 11.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

Page 30

Tempest ™/Cocktail

Disassemble in the order Indicated. (Circled numbers. Match the steps described below.)

Close the control panel. Remove the two set screws in the control knob. Open the control panel. Unplug the four-pin harness Connector. Remove the carriage bolts thai hold the encoder wheel frame to the control panel.

To Lubricate:

  • Loosen the two socket-head screws that attach the hub to the shaft.
  • Unsnap the bottom clip ring. Pull the shaft up and out of the frame being careful not to drop the flywheel.
  • Lightly lubricate the washer and the two nylon bushings that snap into the top and bottom the the frame. Apply Nyogel 779 to a cotton swab for this process.

To Replace the Encoder Wheel: 4, Remove the three socket-head screws that attach the top to the bottom flywheel.

  • Remove the etched encoder wheel and replace it with a new one. Reassemble in reverse, making Sure that you center the new wheel between the photosensor device.

PHOTOSENSOR

ENCODER WHEEL To Replace the Coupler PCB:

  • Remove the two socket-head screws, lock washers and hex nuts that hold the coupler PCB to the frame.
  • Remove the coupler PCB and repair as needed.

Figure 13 Encoder Wheel Maintenance and Repair

  • Encoder Wheel Maintenance and Repair The encoder-wheel control requires \ubrication of its bushings approximately every 10,000 credits and as you deem necessary. To lubricate or repair the control, remove the control from the control panel and disassemble it as illustrated in Figure 13. For lubrication, use only Nyogel 779 \ubricant (Atari part no. 178027-001) on the two bushings of the encoder-wheel control.

For further instructions on how to replace the coupler PCB or the encoder wheel, see Figure 13.

Page 31

D. Video Display Kemoval

The following procedure should be performed by a qualified service technician.

WARNING Shock Hazard High voltages may exist in any television or display, even with power disconnected, Use extreme caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any display. Tempest Cocktail

To remove the color X-Y video dispiay, refer to Figure 14, and follow steps 1 thru 5.

Be sure the game is unplugged from its wall outlet! Unlock and open the table top and access panel. Remove the display bezel.

  • Slightly loosen the four hex nuts that attach the display frame to the display handles.
  • Reach through the access panel opening and unplug the 15-pin video display connector underneath the display.
  • Open both control panels (see Section C, The Control Panel). Remove the two hex-head screws, flat and lock washers on each control panel. This hardware attaches the video display to the cabinet.
  • Grasp the two video display handles and carefully lift the video display assembly up and out the cabinet. After servicing, reassemble in reverse order.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 14 Video Display Removal

Page 32

Tempest™/Cocktail

E. Printed-Circuit Board Kemoval

You may wish to remove the game printed-circuit boards (PCBs) or the Regulator/Audio |i PCB for service or inspection. To do this, refer to Figure 15 and proceed as follows:

  • Game PCB Removal @ Unlock and open the table top. @ Remove the beaded nylon tie-wraps that secure the edge connectors at the top of the PCBs. Next, remove the two edge connectors. @ Remove the Phillips-head screw that attaches the PCB mounting bracket to the cabinet. @ Remove the PCBs from the game by carefully sliding them straight up out of the wood PCB retainers. Be careful not to twist the boards, as this may loosen connections or components. Replace or repair as required. @ After servicing, reinstall the PCBs, making sure that the edge connectors are properly plugged in. Note that the connectors are keyed to fit only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you replace a PCB.

Regulator/Audio Il PCB Removal Unlock and open the table top. Remove the five plug-in connectors on the Regulator/Audio {| PCB. Note that all of these connectors are keyed for proper orientation. Remove the Phillips-head screw and flat fiber washers that are used to attach the PCB to the wood block on the cabinet wall. Grasp the plastic retainer at the top of the PCB and gently lift it up to release the top of the PCB from the retainer. Carefully, remove the PCB by pulling it up and out of the bottom plastic retainer. After servicing, reinstall! the PCB, making sure that it fits into the grooves of the plastic PCB retainers.

Page 33

Tempest™/Cocktail

AUXILIARY PCB

ANALOG VECTOR. GENERATOR PCB

REGULATOR! AUDIO Il PCB

CAUTION Be sure to let the game cool down (with power tured off and the table top open) for at least 10 minutes. The large black heat sink on the Regulator/Audio || PCB gets fairly hot. You could burn yourself on this heat sink while removing the PCB.

Figure 15 Printed-Circuit Board Removal

Page 34

Tempesi™/Cocktail

REGULATOR) AUDIO II PCB

SLIP-ON CONNECTORS

SPEAKER

Figure 16 Speaker and Fan Removal

F. Speaker and Fan Kemoval

If the speaker or fan need to be replaced, follow these instructions and refer to Figure 16.

Unlock and open the table top. Remove the Regulator/Audio !| PCB located above the speaker and fan. To remove the speaker, unptug both speakerwire connectors. Use a short-handled Phillips screwdriver to remove the screws that attach ihe speaker to the cabinet wall. Repair or replace the speaker as required. To remove the fan, unplug both fan-wire connectors. Use a short-handied Phillips screwdriver to remove the screws that attach the fan to the cabinet wall. Repair or replace the fan as required.

CAUTION Be sure to let the game cool down (with power turned off and the table top open) for at least 10 minutes. The large black heat sink on the Regulator/Audio li PCB gets fairly hot, and you could burn yourself on this heat sink while removing the speaker or fan.
Page 35

G. Game Operation

With this manual you received three large sheets that contain the wiring and schematic diagrams for the Tempest™/Cocktail game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams explain the functions of the circuits and define inputs and outputs.

In addition, you received the Tempest Troubleshooting Guide, which includes information on signature analysis, CAT Box tests and the memory map. Tempest™/Cocktail

Atari’s Tempest/Cocktail is a microprocessorcontrolled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCBs and output to the video display, Regulator/Audio || PCB, and control panel.

The color XY display receives signals for the X and Y axes and three color intensity signals (red, green and blue). Since the location of the beam in the display is controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X-and Y-axis inputs to the display step in increments of approximately 760

START SWITCHES

POWER SUPPLY

REGULATOR/AUDIO II PCB VIDEO DISPLAY

POWER INTERLOCK SWITCH

AUXILIARY PCB

ANALOG VECTOR- GENERATOR PCB

ONIOFF SWITCH

Figure 17 Power Distribution

Page 36

Tempest™/Cocktail

steps for the X (horizontal) axis, and approximately 1000 steps for the Y (vertical) axis. The three intensity signals control the brightness of the three electron guns (red, green and blue).

The Regulator/Audio !| PCB has three functions:

  • it regulates the voltages from the power supply to +5 VDC, 2) it rectities and filters + 22 VDC, and 3) it amplifies the audio output from the Auxiliary PCB.

Specifically, the +5 VDC from the Regulator/Audio II PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCBs: +22 VOC is regulated on the Analog Vector-Generator PCB to produce + 15; and + 22VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio I! PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door on the utility switch panel.

The power supply is the source of all voltages in the game. These voltages are protected by five fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the Power supply chassis.

Figure 17 illustrates the distribution of power in this game. Figure 18 illustrates the distribution of signals.

VOLUME CONTROL, SELF-TEST AND COIN SWITCHES

START SWITCHES

SLAM SWITCH

COIN COUNTER

COIN DOOR

REGULATOR/AUDIO Ii PCB VIDEO DISPLAY

CONTROL PANEL

AUXILIARY PCB

ANALOG VECTOR. GENERATOR PCB

SPEAKER

Figure 18 Signal Distribution

Page 37

Illustrated

Parts Lists

This chapter provides the necessary information for you to order replacement parts for this game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “‘A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed on page vi for your convenience.

Page 38

Tempest™/Cocktail

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This. 037829-01 drawing is only conditionally issued, and neither recelpt nor ‘Over! possession thereof confers or transfers any right in, or li- (Overlay) A037868-01 cense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right 178034-026 (Main Harns.) to reproduce this drawing or any part thereof. Except for manutacture by vendors of Atal, Inc., and for manufacture under the corporation's written license, no right is granted. to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. (T-Molding)

Auxiliary PCB Assy.— see Figure 23

Analog Vector-Generator PCB Assy.— see Figure 24 ‘A037450-01 (interl, Sw/Brkt. Assy.) 74-5608NN A 007882-02 (Spacer) (Interl. Sw. Cvr)

71-2110 (Lock) 71-3201 (Wsr. for Lock)

036764-01 (Cam) A037968-01 (Power Harns.)

034536-03 (Vibra. Damper) Sy 178034-025 Z 7 _ (Molding) =>} e Reg/Audio I! PCB Assy. see Figure 22

035745-03 (PCB Retainer) 69-001 : (Self-Test Sw.) S ’ 148001-001 19-9032 (Speaker) (Rheostat) 62.041 00999201 (Util, Coin Sw.) (On/Off Sw. Cvr.) 75-9910NO 4037470-01 (Nut) (OnlOft Sw./Plate Assy.) 037865-01 (Bracket) 171002-001 (Fan)

178034-024 (T-Molding) 037827-01 A002465-01 (Leg Backpiate) (Coin Counter) Power Supply Assy.— see Figure 25 A007638-01 (Slam Sw. Assy.) A037491-01 178013-001 037836-01 (Coin Box) (Latch) (Shield)

Figure 19 Cabinet-Mounted Assemblies A037900-xx A

Page 39

Tempest™/Cocktail

Schematics, Self-Test Label & Manuals— see parts list on following pa: Pi ing page 82-406 (Eyebott) 037427-01 (Vibra. Damper) 037808-02 (Top) 037839-01 037905-01 (Latch Brkt.) (Disp. Shield/Graphics)

037830-01 035852-01 (Bezel) (Corner Brkt.) 037831-01 (Disp. Mntg. Brkt.)

78-3118 (Suppoit) 92-053 (Color XY Display)

035851-01 (Hinge) 036774-01 were) (eile) Control Panel Assy.— see Figure 20 ‘A037907-01 037822-03 (Cab. Base Assy.) (Access Panel) A037292-01 (Leg Supp.)

037825-01 037427-01 (FantSpkr. Grille) (Vibra. Damper) A037453-02, A037454-02, A037455-02 or A037784-02 (Power Cord) Encoder Wheel Assy.— see Figure 21

036773-01 (Grille)

62.039 S| (LED Sw.) A

037843-01 (Start Sw. Mntg. Brkt.)

036895-01 (Sw. Bezel) 037335-02 (Brace)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spect Coin Door Assy.— fic written permission of Atari, Inc., Sunnyvale, CA. This drawi ing’ is only conditionally issued. and neither receipt nor see Figure 26 A037246-01 possession thereof confers of transfers any right In, or Ih Bense to use. the subject matter of the drawing oF any design (Leg Assy.) ‘or technical information shown thereon, nor any right to reproduce this drawing of any part thereat. Except for manutac 78-3206 {ure by vendors of Atari Inc. and Yor manufacture under the (Leg) Corporation's writen license, no rights granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Figure 19 Cabinet-Mounted Assemblies A037900-xx A

Page 40

Tempest™/Cocktail

Figure 19 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A002465-01 Coin Counter A007638-01 Slam Switch Assembly

A037246-01Leg Assembly(includes leg, 2 adjustable feet and 2 endcaps)

A037292-01 Leg Support Assembly (inc/udes 2 panel nuts and endcap) A037450-01 Interlock SwitchBracket Assembly

A037453-02Strain-Relief Power Cord(U.S. and Canada)

A037454-02 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455.02Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly A037491-01 Coin Box A037784-02 Strain-Relief Power Cord Assembly (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A037868-01 Main Harness Assembly

A037907-01Cabinet Base Assembly(includes !eg backplates and PCB retainers, but not the access panel)

A037968-01 Power Harness Assembly A037851-01 Printed-Circuit Board Interconnector The following seven items are the technical information supplements to this game: DP-193-01, 02, -03 Tempest//Cocktail Schematic Drawings (Sheets 1, 2, 3) ST-193 TempestiCocktail Label with Self-Test Procedure and Option Switch Settings TM-183 Service Manual for 19-Inch Wells Gardner Color X-Y Display TM-193, Tempest/Cocktail Operation, Maintenance and Service Manual TM-195 Tempest Troubleshooting Guide 19-9032 50 Ohm, 12%2W Wire-Wound Rheostat (for volume control) 62-039 STDP Momentary-Contact LED Start Switch 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch 62-001 DPDT Self-Test Switch 71-2110 Panel Cartridge Lock Mechanism (for access panel and table top) 71-3201 ¥Y-Inch Anchor Washer for Table-Top Lock 74-5608NN #6 Spacer for Mounting Game Printed Circuit Boards 7507017 Washer for Mounting PCBs

75-9910NO#5;-11 Steel Stamped Nut(for utility coin switch)

7824012 5-Inch Beaded Nylon Tie Wrap 78-3118 Hinged Table-Top Support 78-3206 Cabinet-Leveling Leg 82-406 #1%-20 x 2-Inch Eyebolt with %4-Inch Threads 92-053 19-Inch Welis-Gardner Color X-Y Display 00788202 Interlock Switch Cover 00999201 OniOff Switch Cover 034536-03 Foam Vibration Damper (for PCBs) 035745-03 10-Inch Plastic PCB Retainer 035851-01 Table-Top Hinge 035852-01 Corner Bracket for Table Top

036764-01Hook-Type Cam(for table-top lock)

036773-01 Cabinet Base Giille 036774-01 Upper End-Panel Grille 036895-01 Black Molded Switch Bezel 037335-02 Leg Brace 037427-01 Foam Vibration Damper (for table top and access panel) 037808-02 Wood Table Top

037822-03Access Panel(does not include lock)

{Continued on next page]

Page 41

Tempest™/Cocktail

Figure 19 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description

037825-01 Fan/Speaker Grille 037826-01 Slip-in Cabinet Grille 037827-01 Leg Backplate 037829-01 Display Overlay 037830-01 Display Bezel 037831-01 Display Mounting Bracket 037836-01 Metal Shield for Power Supply 037839-01 Spring Draw Latch Bracket 037843-01 Start Switch Mounting Bracket 037865-01 Bracket for Volume Control, Self-Test Switch and Coin Counter 037905-01 Display Shield with Graphics 148001-001 6 x 9Inch, 4-Ohm, 15W Oval High-Fidelity Speaker 171002-001 110V Cooling Fan 178013-001 Spring Draw Latch 178034-024 %4-Inch Black Plastic T-Molding (for center cabinet base) 178034-025 *y,-Inch Black Plastic T-Molding (for cabinet ends) 178034-026 ‘%e-Inch Black Plastic T-Molding (for table top)

Page 42

Tempest™/Cocktait

A037870-01 Encoder Wheel Assy.— (Harness) see Figure 21

CAUTION Players may receive an electric shock if this control panel is not properly Za grounded! After servicing any parts on the panel, check that the green ground wire is firmly attached to the metal tab ‘on the inside of the contro! panel. Only then should you lock up the game.

160013-001 (Leat Sv. wi Button Holder) 75.9418 (Nut)

75-0108 (Washer)

A037904-01 (Ctrl. Pal /Graphies) 037908-01 (Decal)

TESS10N0 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING (Nut) CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari. Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, of li cense to use, the subject matter of ine teasing or my et 178030-003 75-5108B {otroprace fi drawing or any part teroo}. Excypt for vendor tor —_ al eros wn leans ote gana to reproduce this drawing : the subject matter thereof, unless by written agreement with or witten permission trom the corporation

Figure 20 Control Panel Assembly A037901-01 A Parts List

Part No. Description

A037904-01 Control Panel with Graphics A037870-01 Control-Panel Harness 73-834 Control Knob with Skirt 75-010S #10 Flat Washer 75-941S #10-24 Polymer Hex Nut 75-5108B #10-24 x Ye-Inch Carriage Bolt 75-9910NO #%-11 Steel Stamped Nut 037908-01 Control Panel Graphics Decal 037911-01 Control Panel 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-003 Pushbutton Assembly

Page 43

Or

036795-01 (Shaft)

76-080401 (Bushing)

a Gx 178012002 (Ring)

A035220-01 or -02 (PCB Assy.)

75-9148 (Washer) (Nut)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nov Possession thereof confers or transfers any right in, oF fi cense to use, tne subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, inc., and for manufacture under the corporation's writen license, no right /s granted to reproduce this drawing or the subject matter thereot, unless by written agreement with or written permission from the corporation,

Figure 21 (Screw)

(Encoder Wheel) Tempest ™/Cocktail

75-07047 (Washer) (Knob)

03679401 (Frame)

036796-01 (Flywheel)

036798-01

036797-01 (Flywheel Cap)

Encoder Wheel Assembly A037781-01 A

Page 44

Tempest ™/Cocktail

Figure 21 Encoder Wheel Assembly Parts List

Part No. Description A035220-02 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Alloy Stee! Machine Screw 73-834 Contro! Knob 75-044S #4 Zinc-Plated Steel Split-Lock Washer 7507047 Nylon Washer 75-914S #4 Hex Socket-Head Cap Steel Machine Nut 76-080401 Dual Shoulder Radial Polymer Bushing 036794-01 Frame 036795-01 Shaft 036796-01 Top Flywheel 036797-01 Bottom Flywheel Cap 036798-01 Etched Encoder Wheel 178012.002 “Klip-Ring” Retaining Ring 178027-001 Nyoge! 779 Lubricant

Page 45

Tempest™/Cocktail

  • = NOTICE TO ALL PERSONS RECEIVING THIS DRAWING R33 CONFIDENTIAL: Reproduction forbidden without the spe- Scere cific written permission of Atari, Inc.. Sunnyvale, CA. This

o i” drawing is only conditionally issued, and neither receipt nor

= 7 possession thereof confers or transfers any right in, of li

a—sZl0cense fo use, the subject matter of the drawing or any de-
Cc)CRO9isign or technical information shown thereon, nor any fight
4yeh?Az0to reproduce this drawing or any part thereof. Except for
-as23manutacture by vendors of Atari, Inc., and for manufacture
==2Under the corporation's written license, no right is granted
coato reproduce this drawing or the subject matter thereot, un-
Se%less by writtenagreement with or written permission from

c20 Cat ta

00Caethe corporation.

ar) a

+3300—

35V

TIP 32 TDAe Oe TDAZOO2A 1 .

79 cre ceaJS | cst \ Re cla

220 ]Rel i/2w

Figure 22 Regulator/Audio || PCB Assembly A035435-02 E

Page 46

Tempest ™/Gocktail

Figure 22 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 12-52P7 2,7 Ohm, +5%, 1W Resistor (R5) 16-54P0 4 Onm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 .1 Ohm, +3%, 7W Wirewound Resistor (R24)

19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)
24-2501081000 yf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)

24-250477 470 ut Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226, 22 yf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31)

24-3503383300 uf Aiuminum Electrolytic Fixed Axial-Lead 35V Capacitor(C8, 10, 18, 19)

24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead S50V Capacitor (C22, 23)

29-088-1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C3, 11, 20, 21)
31-1N4002100V 1-Amp. Silicon Rectifier Type 1N4002 Diode(CR1, 4)
31-1N5401100V 3-Amp. Silicon Rectifier Type 1N5401 Diode(CR5¢8)
33-TIP32PNP Power Transistor, Type TIP32(Q2)

34-2N3055, NPN Silicon Transistor, Type 2N3055 (Q3) 37-LM305 5V Linear Voltage Regulator (Qi) 37-7812 +12V Voltage Regulator, Type 7812 (Q8)

37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x V2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Stee! Machine Screw 72-6606S #6 x jInch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Piated-Steel Screw (Q8) 75-F60405 #6-32 x %4-Inch Binder-Head Nylon Screw (Q5, 7) 75-99516 #6-32 Nut/Washer Assembly

78-16008.Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)

79-58308 9-Position Connector Receptacle (J7)

79-5834612-Position Connector Receptacle(J10)
79-83544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink

100015-103..01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C5, C14)
110000-0101 Ohm, +5%, %4W Resistor(R10, 19)

110000-100 10 Ohm, +5%, %W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, +5%, %W Resistor (R4, 12, 22)

110000-1021K Ohm, +5%, %W Resistor(R27, 28)
110000-10310K Ohm, +5%, YW Resistor(R13, 14)
110000-271270 Ohm, +5%, %W Resistor(R1)

110000-330 33 Ohm, +5%, %W Resistor (R3)

110000-3923.9K Ohm, +5%, %W Resistor(R6)
110000-5625.6K Ohm, +5%, %W Resistor(R32, 33)

110000-752 7.5K Ohm, +5%, YsW Resistor (R7)

110001-221220 Ohm, +5%, ¥2W Resistor(R9, 21)

116000-220, 22 Ohm, +5%, 10W Wirewound Resistor (R31) 122002-102 .001 yf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 ut Ceramic-Disc 25V Capacitor (C6, 8, 15, 17)

137151-002Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
Page 47

Tempest™/Cocktail

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wntten permission of Atari, Inc,, Sunnyvale, GA. This drawing is only condiionally issued, and neither receipt nor possession thereof confers or transters any right in, or lie Cense to use, the Subject matter of the drawing or any design ‘ (F technical information shown thereon, nor any right to re produce this drawing or any part thereot: Except for manufac. ture by vendors of Ataf, Inc., and ior manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof. uniess by written agreement with cr written permission from the corporation,

'BICOs- OO!

erie =

Beas 1BI90O4- 001

Gitez

esa faccoa) L =2S"5 BR Lst0a8-c0! L

f Ee aa

  • ae 3 may see as) Lsra§ Lsi57§ monly dh = u

ee Sa 7, aay ard

cozeg4-o1 [keer

' = fe fa #

Figure 23 Tempest™ Auxiliary PCB Assembly A037585-01 B

Page 48

Tempest™/ Cocktail

Figure 23 Tempest™ Auxiliary PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) €012294.01 Audio l}0 N-Channel MOS/LSI Custom Chip _(B/C2, C/D2) 21-101153 .015 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C9, 10) 24-250107 100 uf Alurninum Electrolytic Fixed Axial-Lead 25V Capacitor (C56)

24-25047647 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)

24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C37, 38) 24-500105 1 yi Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C31, 32, 45-47) 24-500476 47 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C19-21) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 11, 12, 14, 15, 17, 18, 22-30, 33-36, 39-44, 49-55)

31-1N100100V Type-1N100 Switching Diode(CR3, 4)
37-LM324Type-LM324 Integrated Circuit(K3, K6)
37-4584BType-4584B Integrated Circuit(E6)
37-74109Type-74109 Integrated Circuit(A2)
37-74LS00Type-74LS00 Integrated Circuit(D4)
37-74LS02Type-74LS02 Integrated Circuit(J4)
37-74LS10Type-74LS10 Integrated Circuit(C5)
37-74LS14Type-74LS14 Integrated Circuit(Fa)
37-74LS32Type-74LS32 Integrated Circuit(C4)
37-74LS74Type-74LS74 Integrated Circuit(C6, D5)
37-74LS139Type-74L$139 Integrated Circuit(B4, B5)
37-74LS157Type-74LS157 Integrated Circuit(D6)
37-74LS161Type-74LS161 Integrated Circuit(C1, D1)
37-74LS174Type-74LS174 Integrated Circuit(A3, H4)
37-74LS175Type-74LS175 Integrated Circuit(J3)
37-74LS191Type-74LS191 Integrated Circuit(A4)
37-74LS244Type-74LS244 Integrated Circuit(E3, H3)
37-74LS374Type-74LS374 Integrated Circuit(B1, F3)
37-74S08Type-74S08 Integrated Circuit(E4)

38-MVS053 Type-MV5053 Red Light-Emitting Diode (CR1) 66-114P1T 4-Station, Single-Throw, Duai-Inline-Package Bit Switch (D/E2)

79-42C1616-Contact Medium-insertion-Force Integrated Circuit Socket(A1, E1, F1, H1, J1, K1, L1)
79-42C2222-Contact Medium-Insertion-Force Integrated Circuit Socket(C3)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(B/C2, C/D2, E2, F/H2, J2, K/L2)
110000-1021K Ohm, +5%, %W Resistor(R1, 5, 7, 41, 45, 53-58, 64, 66-70)
119000-10310K Ohm, +5%, %W Resistor(R3, 4, 8-26, 36, 48-52)
110000-104100K Ohm, +5%, %W Resistor(R35, 37, 38)
110000-151150 Ohm, +5%, ‘4W Resistor(R2, 30, 31)
110000-221220 Ohm, +5%, %W Resistor(R65)

110000-223 22K Ohm, +5%, ¥4W Resistor (R34)

110000-3323.3K Ohm, +5%, YaW Resistor(R39, 40, 46, 47)
110000-334330K Ohm, +5%, %W Resistor(R32, 33)
110000-471470 Ohm, +5%, %4W Resistor(R42-44, 59-63)

110000-472 4.7K Ohm, +5%, %4W Resistor (R29)

110000-47347K Ohm, +5%, VW Resistor(R6, 28)

110001-102 1K Ohm, +5%, ¥2W Resistor (R27) [Continued on next page}

Page 49

Tempest™/Cocktail

Figure 23 Tempest™ Auxiliary PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C16) 128002-102 1000 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C48)

131003-001Type-1N5257B Zener Diode(CR2)
136002-126Programmable Read-Only Memory(A1)
136002-127Programmable Read-Only Memory(E14)
136002-128Programmable Read-Only Memory(F1)

136002-129 Programmable Read-Only Memory (H1)

136002-130Programmable Read-Only Memory(J1)
136002-131Programmable Read-Only Memory(K1)
136002-132Programmable Read-Only Memory(L1)
137002-001Type-74S86 Integrated Circuit(E5)
137003-001Type-74S03 Integrated Circuit(F5)

137004-001 Transistor Array (E2, F/H2, J2, K/L2)

137161-001Read-Only MemoryE£R2055(C3)Note: /f you replace this part, you must erase this ROM

before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. If you do not erase the ROM, the self-test will show the ROM to be “defective” by displaying the letter E on the screen. 179014-012 12-Pin Polarized PCB Header (J16, J17) 179051-001 Test Point

Page 50

CIOTCE TO ALL PERSONS RECENING THIS DRAWING Sz s DETAIL

OB 2 Use IC pads enclosed with dotted

eRe = lines when inserting 74LS245. The

soe 4 other pads are for inserting an 8304B

S383 8 at locations F2, H2, and H3. £38 23 re A #: “oo0de00000, roreproduce mao : FF E% | Bessegee0n iss writen agreement with or witenpormsan trom ead og. £2 i

2 | 3 acz € Pewee E seze G8 05090000007 82 gangs 32 _ 5 8 6000 00c00e ase Bs 5cs5az 2K install W3 and W4 for -01, 02 PCB LBS— 555555 56 5555 43 _ assemblies gece S258 $3 ss8ass Install W1 and W2 for -03, 04 PCB 2283 eee eg SS8S88 Install R19-30 when using 74LS170, assemblies Pees 8888 "2 5

c a Tempest™/Cocktail

  • WES | . Bees =i TEN yy A Pp . (ez! ~ N frees uM (Geaac [aaxt al K rest) tared J ern) [eer Ces C2? H ORR Sad Tonal (ats ren

am F (So} Gena} St = Gee

esc eG Oe E to Oo fet fe ne re 7} oF teen . a | res fp Seats 4 1 2 c | et ag) 4 Get Cag ! ge Get Sia erred | | i Crass <9aGD 20 <3 oD B ' { (font ek MG et ee, ee

  • 4 == pee waopl = A = . col | a OF ae Coufal foal GB
  • Ft mo Cel 8 1 2 3 4 5 6 7 8 Qa 19 11 12 13

Figure 24 Tempest™ Analog Vector-Generator PCB Assembly A037383-01 thru -04

Page 51

Tempest™/Cocktail

Figure 24 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 19-315103 10K Vertical PCB-Mounting Cermet Trimpot (R147, 150, 167, 168) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R117, 118) 19-315202 2K Ohm Vertical PCB-Mounting Cermet Trimpot (R165, 169) 21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 & -04 PCB assy. only: C63)

24-250266 22 pf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (For -01 & -02 PCB assy. only: C60,C62) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C57-59) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C61) 27-102182 .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -07 & -03 PCB assy. only: C67. For -02 & -04 PCB assy. only: C75)

29-006 1 uf, + 10%, 35V Tantalum Capacitor (For -03 & -04 PCB assy. only: C60) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-19, 22-49, 51, 53-55, 69, 71, 77-80, 82-85, 88-91, 93-97, 99, 102, 103. Also, for -01 & -03 PCB assy. only: C66, 68, 72, 73. For -02 & -04 PCB assy. only: C64, 65, 74, 76) 31-1N 100 100V Type-1N100 Switching Diode (CR4)

31-1N91475V Type-1N914 Switching Diode(CR1)

33-2N3906 Type-2N3906 PCB Switching and Amplifying Transistor (Q9-11) 34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1-4, 8, 12) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q5, 7)

37-TLO82CPType-TLO82 Integrated Circuit(A11, 011, DIE12, D/E13, K11)
37-1495Type-MC1495L Integrated Circuit(A/B12, A/B13, C12, C13)
37-13201Type-LF13201 Integrated Circuit(B11, E11)
37-74LS00Type-74LS00 Integrated Circuit(K9)
37-74LS02Type-74LS02 Integrated Circuit(A7, B5)
37-74LS04Type-74LS04 Integrated Circuit(J11)
37-74LS08Type-74LS08 Integrated Circuit(A4)
37-74LS10Type-74LS10 Integrated Circuit(F4)
37-74LS14Type-74LS14 Integrated Circuit(E6)
37-74LS20Type-74LS20 Integrated Circuit(E9)
37-74LS27Type-74LS27 Integrated Circuit(B6)
37-74LS32Type-74LS32 Integrated Circuit(C3, J8, B9, R7)
37-74LS42Type-74LS42 Integrated Circuit(F7)
37-74LS74Type-74LS74 Integrated Circuit(B8, D3)
37-74LS109Type-74LS109 Integrated Circuit(A8)
37-74LS139Type-74LS139 Integrated Circuit(B3, C1, J2, J5, P7)
37-74LS157Type-74LS157 Integrated Circuit(K2,L2, M2, N2, P8)
37-74LS161Type-74LS161 Integrated Circuit(E4, C8, D8, £8, F8)
37-74LS 164Type-74LS164 Integrated Circuit(A9)
37-74LS174Type-74L$174 Integrated Circuit(E7, H8, N8, N9)
37-74LS175Type-74LS175 Integrated Circuit(H7, J7, K8)

37-74LS191 Type-74LS191 Integrated Circuit (J6, L8)

37-74LS193Type-74LS 193 Integrated Circuit(K5, L5, M5)
37-74LS194Type-74LS194 Integrated Circuit(D5, D6, E5, F5, H5, H6)
37-74LS244Type-74LS244 Integrated Circuit(A/B1, BIC1, E2, M12, N12, R9)
37-74LS245Type-74LS245 integrated Circuit(F2,H2,H3) Acceptable substitute is part no. 37-8304B.

37-74LS273 Type-74LS273 Integrated Circuit (D9)

37-74LS367Type-74LS367 Integrated Circuit(K7, N7)
37-74LS393Type-74LS393 Integrated Circuit(B4, D4)

[Continued on next page]

Page 52

Tempest™/Cocktail

Figure 24 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74LS399Type-74LS399 Integrated Circuit(H9)
37-74LS670Type-74LS670 Integrated Circuit(K6,L6,M6) Acceptable substitute is part no. 37-74LS170.
37-74S00Type-74S00 Integrated Circuit(F6)
37-74802Type-74S02 Integrated Circuit(C6)
37-74S04Type-74S04 Integrated Circuit(A6, E3, N6)
37-74S808Type-74S08 Integrated Circuit(F3)
37-74S74Type-74S74 Integrated Circuit(B7, C7)
37-74S260Type-74S260 Integrated Circuit(C5)
37-74193Type-74193 Integrated Circuit(C4)

37-7815 + 15V Voltage Regulator (VR3)

37-7915— 15V Voltage Regulator(VR1)

38-MV5053, Type-MV5053 Light-Emitting Diode (CR2)

41-3003100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke(L1) Acceptable substitute is part

no. 141002-001. 62-001 SPST Momentary Pushbutton Switch (Reset)

66-114P1T4-Station SingleThrow, Dual-Inline-Package Bit Switch(K10/11)
66-118P1T&Station Single-Throw, Dual-Inline-Package Bit Switch{L12, N13)

78-13003 General Electric RTV #108 Sealing Compound

79-42C1616-Contact Medium-Insertion-Force Integrated Circuit Socket(D7)
79-42C2424-Contact Mediurn-Insertion-Force Integrated Circuit Socket(01, E1, F1, H1, J1, K1, L/M1,

MIN1, P1, R1, N/P3, R3)

79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C2)

81-4302 Nylon Snao-In Fastener 90-6013 Microprocessor (C2)

90-7005Random-Access Memory(P98)
90-7033Random-Access Memory(J3, J4, K3, K4, L3, L4, M3, M4, P2, P4, R2, Rd)

99-130430 Voltage-Dependent Resistor (RV1,2) Acceptable substitute is part no. 110004-001. 020670-01 Test Point

110000-101100 Ohm, «5%, YW Resistor(R107, 111)

110000-102 1K Ohm, +5%, %W Resistor (R3, 13, 15, 31, 32, 34, 35, 62-67, 81, 129, 142, 160) 110000-103 10K Ohm, +5%, %W Resistor (R1, 2, 4-12, 14, 16, 17, 38, 60, 61, 84, 87-102, 128, 134, 139, 156, 158. Also, for 01 & -03 PCB assy. only: 105, 106, 112.) Also, tor any PCB assy. if you are using part no. 37-74LS170 in locations K6, L3, M6: R19-30)

110000-104100K Ohm, +5%, 14W Resistor(R42-49)
110000-1221.2K Ohm, +5%, YW Resistor(R40)

110000-151 150 Ohm, +5%, %W Resistor (R86)

110000-15215K Ohm, +5%, YW Resistor(R137)
110000-15315K Ohm, +5%, %W Resistor(R58, R130)
110000-221220 Ohm, +5%, ¥4W Resistor(R18, 85)
110000-2222.2K Ohm, +5%, YaW Resistor(R97, 52, 54, 56, 131-133, 144, 153-155, 163)
110000-22322K Ohm, +5%, %4W Resistor(R36, 82)
110000-2722.7K Ohm, +5%, YsW Resistor(R141, 157, 161)

110000-331 330 Ohm, +5%, YW Resistor (R51, 53, 55, 57, 74-76)

110000-3923.9K Ohm, +5%, %4W Resistor(R41, 110, 138, 143, 145, 162, 164)
110000-47047 Ohm, +5%, %4W Resistor(R80)
110000-471470 Ohm, +5%, %W Resistor(R68-73, 135, 136, 148, 151, 170, 173)
110000-4724.7K Ohm, +5%, %W Resistor(R39, 59, 77-79)

[Continued on next page]

Page 53

Tempest™/Cocktail

Figure 24 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-561560 Ohm, +5%, %4W Resistor(R127)

110000-562 5.6K Ohm, +5%, %W Resistor (R146, 166) 110000-681 680 Ohm, +5%, %W Resistor (R140, 159. Also, for -02 & -04 PCB assy. only: R113)

110000-6826.8K Ohm, +5%, ’4W Resistor(R50)
110000-68368K Ohm, +5%, %W Resistor(R83)

110000-821 820 Ohm, +5%, %4W Resistor (For -02 & -04 PCB assy. only: R103, 104, 114)

110001-271270 Ohm, +5%, v2W Resistor(R152)
110003-7527.5K Ohm, +1%, %W Resistor(R108, 109, 115, 116, 119-126)
110005-0010 Ohm Jumper (For -01 & -02 PCB assy. only: W3, 4.For -03 & -04 PCB assy. only: W1, 2) Ac-

ceptable substitute is 24-gauge wire. 121007-473 .047 yf, + 10%, Radial-Lead Epoxy-Dipped 50V Polycarbonate Capacitor (C100, 101) Acceptable substitute is part no. 121006-473.

122000-2252.2 uf, + 10%, 35V Tantalum Capacitor(C56)

122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C70)

128002-10010 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C81)
128002-101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C21)

128002-151 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C87)

128002-221220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C52)
128002-39039 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C20, 86, 92, 98)
131002-0016.8V, 400 mW, +5%, Zener Diode(CRS)
136002-101Programmable Read-Only Memory(D1)Acceptable substitute is part no. 136002-113.
136002-1023Programmabie Read-Only Memory(E1)Acceptable substitute is part no. 136002-114.
136002-103§Programmable Read-Only Memory(F1)Acceptable substitute is part no. 136002-115.
136002-1043Programmable Read-Only Memory(H1) Acceptable substitute is part no. 136002-116,
136002-105eSProgrammable Read-Only Memory(J1) Acceptable substitute is part no. 136002-117,

Qa

136002-106S sProgrammable Read-Only Memory(K1) Acceptable substitute is part no. 136002-118.
136002-107isProgrammable Read-Only Memory(LIM1) Acceptable substitute is part no. 136002-119.
136002-1083Programmable Read-Only Memory (MIN1) Acceptable substitute is part no. 136002-120.
136002-1095Programmable Read-Only Memory(P1)Acceptable substitute is part no. 136002-121.

QB

136002-110.3Programmable Read-Only Memory(R1) Acceptable substitute is part no. 136002-122.
136002-111=Programmable Read-Only Memory(N/P3)Acceptable substitute is part no. 136002-123.
136002-112Programmable Read-Only Memory(R3) Acceptable substitute is part no. 136002-124.
136002-125Programmable Read-Only Memory(D7)
136002-133Programmable Read-Only Memory(D1)
136002134 = 42Programmable Read-Only Memory(F1)
136002-135 a a 3Programmable Read-Only Memory(J1)

136002-136 se g Programmable Read-Only Memory (L/M1) a zg

136002-137 SS §Programmable Read-Only Memory(P1)
136002-138,Programmable Read-Only Memory(N/P3)
137002-001Type-74S86 Integrated Circuit(M8)
137149-001Type-74LS11 Integrated Circuit(F9)

137158-002 Type AM6012PC 12-Bit Digital-to-Analog Converter (For -02 & -04 PCB assy. only: A10, F10) Acceptable substitute is part no. 137150-001. 137159-001 Type DAC-08CN 8-Bit Digital-to-Analog Converter (D10) 137160-003 Type MC3410 10-Bit Digital-to-Analog Converter (For -01 & -02 PCB assy. only: B10, E10) Acceptable substitute is part no. 137160-004.

144000-00112.096 MHz, +.005%, Crystal(¥1)Acceptable substitute is part no. 90-102.
179014-01212-Pin Polarized PCB Header(J19)
Page 54

Tempest™/Cocktail

NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atar, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither recelot nor possession thereot confers or transfers any right in, of I cense to use, the subject matter of the drawing or any de- Sign or technical iormation shown thereon, nor any sight to reproduce this drawing or any part thereof. Except for manutagture by vendors of Atari Inc., and for manutacture Under the corporation's written license, ne Tight to repro: ‘duce this drawing Is granted or the subject matter thereot unless by written agreement with or written permission from the corporation A037395-02 (Transtormer Assy.)

A021084-xx (Volt. Plugs)

29-053 (Capacitor) 034544-01

(Fuse Block Cyr.)

79-4411001 (Fuse Post} 78-70501SC

46-2017002 (Fuse) (Cap. Bracket) he A035691-01 (Fuse Harness)

46301203 (Fuse) 034482-02 (Chassis)

037639-01 (Label)

78-2708 (Bushing)

A034630-01 79-3206 (Filter Assy.) (Fuse Block) 037641-01 (Label) 46-2014002 (Fuses)

A035890-01 79-15021001 (Term. Block) (Pwr. Harness)

A034629-01 3A-MDA3501 (AG. Harn.) Rectifier)

Figure 25 Shielded Color X-Y Power Supply Assembly A037875-xx A

Page 55

Tempest ™/Cocktail

Figure 25 Shielded Color X-Y Power Supply Assembly Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(violet)

A021084-02 Voltage Plug for 120V (yellow)

A021084-04Voltage Piug for 220V(blue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 A.C. Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly A037395-02 Color X-Y Transformer Assembly (T1) 29-053 27,000 pf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x ‘%j,-Inch Outside Diameter x 4-Inch Thick 78-70501SC_ 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 §-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-444 1001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover

037639-01Label for Fuse Value(F1)

Labei for Fuse Values (F2-F6) 037641-01

A037875-01 power supply assembly has 120V plug A037875-02 has the 100V, 220V and 240V plugs A037875-03 has the 220V and 240V plugs

Page 56

Tempest ™/Cocktail

99-15051 (Lamp Holder) we

“"— 99-15026

(Coin Inlet) 99-15040 (Lever) 99-15056 (Screw for Bezel)

(Coin Inlet)

PART OF 99-15041

99-15055 - (Retng. Screw) a\ Va

99-15027 (Com Ret. Box) 99-15054 (Pivot for Lever) 99-15041 ° (Lockout Coil) Nea 99-15053 » (Lockt. Coii Spring) <

~——— 99-15028 e Bs (Coin Ret. Box)

(Sw. Adjuster) fa oo] 9.15029 a (Bracket)

99-15042, (Switch) 99-15056 (Screw for Bezel) 99-15060

a (Sw. Cover)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden. without the Speciic written permission of Atari, new Sunnyvale, Co This drawing 1s only conditionally’ issued. and neither receipt nor possession thereo! conters or transfers ary Tight in, or license to use, the subject matter of the crave ing or ny design or technical information shown thereon, ai any ‘right fo reproduce ths arawing oF any. pari thereof. Except tor manufacture by vendors of Atary, Ine, A037542-01 and for manufacture under the’ corporations. written (Harness-not shown) license, no right to reproduce this drawing se granted or the subject matter thereo! unless by writen syvcenect with or written permission trom the corporations

Figure 26 Vertical-Mounted Coin Door A037619-xx B

Page 57

99-15067 (Lock Assy.)

(Screw)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the speaific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF li Cense to use, the subject matter of the drawing or any de- Sign or technical information shown thereon, nor any tight 10 reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right 1s granted to reproduce this drawing or the subject matter thereo!, un: ess by written agreement with or written permission from the corporation,

A037619-01 — U.S. 25¢/25¢ Coin Door ‘A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 —- Canadian 25¢/25e Coin Door A037619-04 — British 10 P/10 P Coin Door A037619-05 — B: 10 P/50 P Coin Door A037619:06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢/20¢ Coin Door 99-15067 (Lock Assy.)

‘A037619-68 — German 1 DM/1 DM Coin Door A037619-09 — German 2 DM/1 DM Coin Door ‘A037619-10 — German 2 DM/5 DM Coin Door A037619-11 — German 1 DM/S DM Coin Door 03761912 — § Fr/5 Fr Coin Door A037619-13 — Swiss 1 Fri1 Fr Coin Door A037619-14 — French 1 Fr/1 Fr Coin Door s > ! AN Tempest ™/Cocktail

99-15038 (Bezel for Button)

99-15001 thru 99-15012 (Ret. Button)

99-15052 (Spring for Button)

99-15065 (Clamp)

99-15039 (Bezel for Cover)

9915066 (Screw)

A037619:15 — French 2 Fr/1 Fr Cain Door A037619-16 — Swedish 1 Kr/1 Kr Coin Door ‘A037619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door ‘803761919 — Hong Kong $1/$1 Coin Door A037619-20 — Japanese 100Y/100Y Coin Door

Figure 26 Vertical-Mounted Coin Door A037619-xx B

Page 58

Tempest™/Cocktail

Figure 26 Vertical-Mounted Coin Door, continued Parts List

Part No. Description

A037542-01 Harness Assembly

99-15001 Coin Return Button with U.S. 25¢ Price Plaie 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20% Price Plate 99-15011 Coin Return Button with italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030, Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-1062 Hinge 99-15063 Screw for Hinge 99-15065 Clamp for Frame 99-15066 Screw for Clamp ‘99-15067 Lock Assembly

Page 59

oe YOUR COMMENTS, PLEASE! eet enntng

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technica! questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm CO Distributor

Address CG Operator

City State Zip C Cther.

Area Code Phone

Page 60

First fold

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

e6pe sy ede,

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

] } PE PGR RG GE LO LG Pp > » ° p >

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective,
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. 5

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

Piles Sates Sate Salad Nate Mateo Nad Satie) Mat The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 64

A.

ATARI

ATARI ING @ 1265 BORREGAS AVENUE e e P.O. BOX 427 ue SUNNYVALE, CALIFORNIA 94086 ® e ® 408/745-2000 © TELEX 35-7488 »