CATHODE RAY TOMES

Satans Hollow Parts and Operating Manual (Oct 1982)

Satan's Hollow (set 1) (Bally Midway, 1981) · Parts & Operating Manual · 108 pages · 47 sections · original scan

Page 1

NO. 941 UPRIGHT

FORM NO. 00941-00300-0000 OCTOBER, 1982 Game Nos. 941, 943, 942

Ballly/ Midway’ 's

Parts & Operating

Manual

NO. 943 MINI

NO. 942 COCKTAIL

MIDWAY MFG. CO.

10750 W. Grand Avenue Franklin Park, Illinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO. Telex No.: 72-1596

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment Generates, Uses and can Radiate Radio Frequency Energy and if not installed and used in accordance with the Instructions Manual, may cause interference to Radio Communications, As temporarily permitted by Regulation it has not been tested for compliance to Subpart J or Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a Residential Area is likely te cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

Sate THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

XPOSURE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CBillly|MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

© COPYRIGHT MCMLXXXII BY BALLY/MIDWAY MFG. CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, ANO NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION PAGE

ue Introduction ©... 6... cece eee ee EEE EE ert EEE ES eee ene n nee te 1-1

Location and Setup Inspection .... Installation . Self-Test ...... Game Volume Adjustment Control . Option Settings

Game Operation Self-Test Mode Attract Mode.. Ready to Play Mode Play Mode......... Two Player Operation ..

Maintenance and Repair Cleaning ...........0+5 A Fuse Replacement ..... 4-1 Opening the Control Panel . 24-2 Removal of the Main Display Glass & T.V. Bezel 4-4 TN. Monitor Replacement.......... 4-5 Printed Circuit Board Replacement. .4-8 Opening the Attraction Panel .. a -4-10 Servicing the Control Panel Black Light (Upright)... 24-12

Mlustrated Parts Breakdown No. 941 — Satan's Hollow — Upright — Front 15-2 No, 941 — Satan’s Hollow — Upright — Front — Parts List . 5-3 No. 941 — Satan’s Hollow — Upright — Rear Access ...... 25-4 No. 941 — Satan’s Hollow — Upright — Rear Access —— Parts List 5-5 No. 941 — Satan’s Hollow — Upright — Header Fluorescent Fixture Assy. .5-7 No. 941 — Satan's Hollow — Upright — Header Fluorescent Fixture Assy. — -5-7 No. 943 — Satan's Hollow — Mini — Front 5-8 No. 943 — Satan's Hollow — Mini — Front — Parts List.... 5-9 No. 943 — Satan’s Hollow — Mini — Rear Access......... ~5-10 No. 943 — Satan's Hollow — Mini — Rear Access — Parts List ... -5-11 No. 941 & 943 — Satan’s Hollow — Upright & Mini —- Control Assy. 5-12 No. 941 & 943 — Satan’s Hollow — Upright & Mini — Control Assy. — Parts List . 5-13 No. 942 — Satan’s Hollow — Cocktail — Front .............. 5-14 No. 942 — Satan’s Hoilow — Cocktail — Front — Parts List 5-15 No. 942 — Satan’s Hollow — Cocktail — Interior Access .. -5-16 No. 942 — Satan’s Hollow — Cocktail — Interior Access — -5-17 No. 942 — Satan's Hollow — Cocktail — Control Assy. — Parts List -5-18 No. 942 — Satan's Hollow — Cocktail — Controi Assy........-..... 5-19 Satan's Hollow — All Versions — Power Chassis Assy., 125VA., 115V .5-20 Satan’s Hollow — All Versions — Power Chassis Assy., 125VA., 115V — Parts List .5-21 Front Door Assy. — U.S.A. 25@.......... 00.008 5-22 Front Door Assy. — U.S.A. 25¢ — Parts List ... + 5-23

Page 4

TABLE OF CONTENTS (cont'd)

DESCRIPTION PAGE

Vi.

Vil.

Vii. Technical Troubleshooting . Introduction . sees General Suggestions .. Harness Component Troubleshooting . Transformer and Line Voltage Problems . A Glossary of Microprocessor Terms .. Introduction to the Z80 CPU. General Purpose Registers ... Arithmetic and Logic Unit (ALU) .. introduction Register and CPU Control. Z80 CPU Pin Description .............. MCR II System P.C. Board Jumper Options...

Coin Door Maintenance Metal Coin Acceptor Mechanisms . Plastic Coin Acceptor Mechanisms

TV. Monitor Manual . .. Introduction . Symptom Diagnosis ... Guide to Schematic Symbols Troubleshooting....... Theory of Operation... Differences Between Monitors Controls You May Not Touch Parts Interchangeability ..... Wells Gardner Monitor Schematic — 19” Wells Gardner Monitor Replacement Parts List . Electrohome Monitor Schematic — 19”.. Electrohome Monitor Replacement Parts Electrohome Monitor Schematic — 13”... Eiectrohome Monitor Replacement Paris

Schematics & Wiring Diagrams Wiring Diagram (All Versions) Dual Power Amp Assy. — Component Layout Dual Power Amp Assy. — Schematic .. Super CPU P.C.B. — Component Layou Super CPU P.C.B. — Schematic....... Video Generator — Component Layout Video Generator — Schematic .......... Super Sound I/O P.C.B. — Component Layout ... Super Sound I/O P.C.B. — Schematic .............. 125VA Power Supply P.C.B. — Component Layout 125VA Power Supply P.C.B. — Schematic 125VA Power Chassis — Schematic

Page 5

FIGURE PAGE

1-1 Assigned Point Values... 2.0.0.0... cece cece cee cece eee eect e eee eee n ees «1-2 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies 12-2 2-2 Major Sub-Assemblies (Cont. from Fig. 2-1) .. 12-3 2-3 Interlock Switch Operation ... 12-3 2-4 Location of Volume Control 12-4 2-5 Option Switch Locations . 12-4 2-6 Option Switch Settings . 12-5 3-1 Identification of “On-Screen 3-1 3-2 Self-Test — Menue .. 3-2 3-2a Self-Test — Sounds . 3-2 3-2b Self-Test — Player Inputs. 13-3 3-2c Self-Test —- Bookkeeping . 13-3, 3-2d Self-Test — Time Report. 8-3 3-2e Self-Test — Score Report. 3-3 3-2f Self-Test — Set-Up Options 13-4 3-2g Self-Test — Channel Test..... 3-4 3-3 Location of Hardware Master Reset Switch . 13-5 4-1 Location of Fuses ...........-...+. eee 4-1 4-2 Opening the Control Panel — Upright & Mini. -4-2 4-3 Opening the Cocktail Game ............. 4-3 4-4 Removing the Control Panel — Cocktail .. 4-3 4-5 Removal of Main Display Glass & TV. Bezel — Upright. 4-4 4-6 Removal of Main Display Glass & TV. Bezel — Mini 4-4 4-7 Removing the Top Glass & T.V. Bezel — Mini . 4-5 4-8 Removing the Monitor — Upright - 14-6 4-9 Removing the Monitor — Mini 4-6 4-10 Opening the Cocktail Game .. 4-7 4-11 Removing Monitor — Cocktail 47 4-42 Removing P.C.B.s ..........000 4-8 4-13 Removing P.C.B.s from Card Rack 49 4-14 Opening the Attraction Panel — Upright . 4-10 4-15 Replacing Fluorescent Tube Starter . (4-14 4-16 Opening the Attraction Panel — Mini. 4-11 4-17 Servicing Control Panel Black Light — Upright . 4412 4-18 Removing Black Light Tube Mtg. Brkt. — Upright. -4-12 7-1 Removing and Replacing the Coin Acceptor. . 7-1 7-2 Cleaning the Metal Coin Acceptor ....-.. 7-2 7-3 Lubricating the Metal Coin Acceptor . 7-2 7-4. Opening the Plastic Coin Acceptor..... 7-3 7-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters 2 TH4 TABLE OF FIGURES

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

Satan’s Hollow

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.

I. Introduction

SATAN’S HOLLOW is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCKTAIL TABLE”. The Upright and Mini models have been designed for either RIGHT or LEFT hand use. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to take their Rocket Launcher through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn.

When playing this game, the Rocket Launcher is under YOUR control. YOU make it move back and forth across the screen to launch Rockets that will eliminate your attackers. These attackers are displayed in groups, called “racks”, across the top of the screen. The first rack is made up of asmall number of attackers. The second rack is made up of a larger number of these attackers. And intermixed with the racks of attackers is a rack with only a single firebreathing Devil's head. The attackers and the Devil's Head will try to wipe out your Rocket Launcher. If they do, you lose one player. In emergencies, you have a Shield which goes all around your Rocket Launcher for a short period of time. It is activated by pushing the Shield Button on the control console. BUT BE CAREFUL!! This consumes a lot Of power and will only last a VERY SHORT TIME! Each attacker eliminated will cause a Bridge Section to appear at the lower left corner of the screen EXCEPT: when there is already a Bridge Section there or when you have a Bridge Section in tow under your Rocket Launcher. Pick these Sections up with your Rocket Launcher and move them over to build a Bridge across the gorge at the right side of the screen leading into the land of SATAN. When you complete your Bridge into the land of SATAN, you can cross it and do battle with him. If you win you will be rewarded by increased fire power for your Rocket Launcher. If SATAN defeats you, you lose one player. As your skill level increases, the number of attackers is increased and the speed that the fire-breathing Devil's Head moves is increased also. Bonus Rocket Launchers are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each attacker has an assigned point value as listed in Figure 1-1.

Page 8

Major Features

There are several major features in your SATAN’S HOLLOW game: 1) a complete and easy-to-use diagnostic package featuring: 2) A complete ROM/ RAM check with bad chip location information readout on the monitor screen; 3) The capability to check each of the game's different sounds INDIVIDUALLY;

  • Provision for checking each control and switch SEPARATELY; 5) A full function Bookkeeping mode; 6} An entire options list that can be set from the front console with NO NEED to craw\ inside the back of the cabinet and look for tiny switches located on P.C. boards; 7) A sound system test; 8) A “PRE-SET” category that returns ALL information in the Bookkeeping mode to zero and all operator selected options back to factory recommended settings; and
  • The game is equipped with a rechargeable battery so that it won't forget where it was the night before at closing — even if you turn it off. It will “remember” this information for up to two weeks.

1-2

Game Objective

The object of the game is to HAVE FUN while constantly improving your skills as you play, eliminating as many attackers as possible each time to get the highest score.

POINTS AWARDED 1000 1000 DESCRIPTION SATAN LUCIFER OLD NICK BEELZEBUB EGG THROWER BRIDGE BOMBER GARGOYLE

Figure 1-1 Assigned Point Values

Page 9

II. Location and Setup

INSPECTION: 1.

2.

. Remove the shipping Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. : O Any scratches?, dents?, cracks? CO Any broken controls? ao 0 Any broken glass or plastic?’ Just look it over closely and make a note of any signs of damage. _ cleats from the bottom of the cabinet. . Install the four levelers, one at each corner of the cabinet. * O Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. O Also check to make sure all plug-in connectors on the wire harness are firmly seated.

NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up. O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.’s willonly go into them one way without being damaged.
Note the location of the game’s serial number. See Figure 2-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 2-1 & 2-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply and filter assembly. . Make a note of any problems that can't be easily corrected. . Call your distributor and/or service man about your problem list. INSTALLATION:
  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative DO Space required: Upright 25” x 32” (63 x 81cm) Mini 20" x 24” (50 x 60cm) Cocktail 32” x 22” (81 x 55cm) O Game height: Upright 70" (175cm) Mini 61" (153cm) Cocktail 29" (73cm)

. Voltage Selection: Your game is designed to work properly onthe line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. if the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.

. Interlock and power ON/OFF switches. See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). O When any access doar is opened, the interlock switch installed there turns off all power to the game.

Page 10

SERIAL NUMBER’

INTERLOCK SWITCH

POWER SUPPLY

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

CONTROL PANEL (PLAYER 1)

INTERLOCK SWITCH (INSIDE DOOR) ON/OFF SWITCH

INTERLOCK SWITCH Loaic BOARDS

POWER SUPPLY : : P.C.B. 3 Loaic : : BOARDS POWER SUPPLY CHASSIS : (NOT SEEN) ms NS IN. POWER ea SUPPLY ON/OFF CHASSIS (NOT SEEN) UPRIGHT

TV. MONITOR

POWER SUPPLY CHASSIS.

POWER SUPPLY P.C.B.

CONTROL PANEL (PLAYER 2)

ON/OFF SWITCH UNDER TABLE COCKTAIL

Figure 2-1 Location ot Serial No., interlock Switch, On/Off Switch and Major Sub-Assys.

2-2

Page 11

CONTROL PANEL

CONTROL PANEL

Figure 2-2 Major Sub-Assys. (Cont. from Fig. 2-1)

O Check each interlock switch for proper After the game has warmed up, repeat the above operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds wiil stop). if this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” Position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-3.

AN No

Figure 2-3 Interlock Switch Operation

Page 12

SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

GAME VOLUME ADJUSTMENT CONTROL: See Figure 2-4. The game volume control pot is located just inside the cabinet on the right side of the coin door frame. There is only one pot. For adjustment, it may be reached through the coin door on ALL models. To make the sounds louder, turn the pots clockwise as you face them (/™ ). To make the sounds less loud, turn the pots counterclockwise as you face them ( ¥).

OPTION SETTINGS: To change the most common option settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet on the right side of the coin door frameas you face it. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game’s P.C. boards, it is also recom-

OPTION SWITCH 3

Figure 2-5 Option Switch Locations SERVICE CREDIT SWITCH

SELF-TEST SWITCH

VOLUME ADJUSTMENT

Figure 2-4 Location of Volume Control

mended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The P.C. Board option switch settings, and what they will make the game do are shown in Figure2-6. These switches are MAINLY INTENDED for use by a technician who is checking and/or performing tests on the game. See Figure 2-5 for option switch locations.

NOTE: In order to set the option switches located on the game’s P.C. Boards, these Boards need not be removed from their card rack.

OPTION SWITCH 1

Page 13

SATAN’S HOLLOW

OPTION SWITCH SETTINGS

SW#1 SW#2 SW#3 SW#4 SW#5 SWH#6 SW#7 SWHB SWH9 SWH10:

2 COIN METERS ON NOT NOT NOT NOT NOT NOT NOT “1 COIN METER OFF USED USED USED USED USED USED USED

MINI/UPRIGHT COCKTAIL TABLE

FREEZE VIDEO ***NORMAL OPERATION

SWITCH NO. 3 — AT D14 — LOCATED ON SOUND 1/0 P. C. BOARD

Swit SWH#2 SW#3 SW#H4 ek *e ek ***NORMAL OPERATION OFF SOUND I/O DIAGNOSTIC MODE

*** NORMAL OPERATION RAM/ROM TEST INDICATES TEST RESULTS VIA YELLOW LED ON SOUND |/O BOARD: FAST FLASH = BAD ROM SLOW FLASH = BAD RAM

***NORMAL OPERATION OSCILLATOR TEST

***NORMAL OPERATION FILTER TEST

PART NO. “* NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF” POSITION. M051-00941-A011 *“"INDICATES FACTORY RECOMMENDED SETTINGS.

THE REMAINDER OF SATAN’S HOLLOW’S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING THE MACHINE SETUP PORTION OF THE SELF-TEST MODE AND WILL BE COVERED IN DETAIL IN THAT SECTION OF THIS MANUAL.

Figure 2-6 Option Switch Settings

2-5

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

Ill. Game Operation

SATAN'S HOLLOW isa one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown in Figure 3-1.

PLAYER 1 SCORE

HIGH SCORE

ATTACKER The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.

PLAYER 2 SCORE (NOT SHOWN)

RIVER OF FIRE

CREDITS

SHIELD TIME

Figure 3-1 Identification of “On-Screen” Graphics During Play

SELF-TEST MODE

The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered.

You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on (the Self-Test switch is located just inside the cabinet on the right side of the coin door frame as you face it). When this is done, the game will react as follows:

  • If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Seif- Test Mode Menue on the monitor screen.
  • If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go inio the Self-Test mode until AFTER the player's last Missile Launcher has been destroyed (the game MUST be over). At this point, the game will go into the Self- Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen.

. The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode. o

Page 16

SELECT DESIR

eo SELF OER

SauRRS

4 PLAYER IN

4 RHOKRKER EINE

S WHEAIWE

CHANNEL

PRESET

GRID OLSPLAY HE

TEST

TTIUN CURSOR BY MOVING CONTROL RANDLE

TRIGGER BUTTON FOR PULL TEST

Figure 3-2 Self-Test — Menue

The Self-Test mode has eight (8) major categories as illustrated by Figure 3-2.

  • Itis easy to select what category you wantto enter. By moving the control stick left or right the Cursor at the left of the screen can be moved UP or DOWN until it is in front of the category you want to test. Release the control stick at this time.

. After the Cursor has been positioned, depress either “SHIELD” Button on the console and the monitor screen will display the test category you have selected.

NOTE: There is one exception to this. If you position the Cursor in front of the “PRE-SET” category on the Self-Test Mode Menue, when you press the “SHIELD” Button on the console — EVERYTHING, | repeat —- EVERYTHING — cluding ALL information in the “BOOKKEEPING” mode, and ALL operator selected options, will be set back to zero (“0”) and to the factory recommended settings — respectively.

O Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.

  • The next group of Figures show the CORRECT screen presentation for EACH category of the Self-Test mode.

3-2 During the SELF DIAGNOSTICS section of the Self- Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by this message: “HIT SHIELD BUTTON TO EXIT”. If the Shield Button is not hit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. If the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game wil! give you a written message as to which parts are bad. This message includes their I.D.'s and their P.C. Board locations.

During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2a. O In this category, each of the game's separate sounds can be checked individually in any order — or — you can tell the game to check them all in order — 3 through 23.

BD DIVER RELENS STERL BARGE FIRE BALL mua ATS Cee wet

a

i

L

i

i

€ tut ‘bog fa § FLA AT OLE TOE: K WE Viti utils ft i AG WV MEMES FAP ergs Se

Figure 3-2a Self-Test — Sounds

Page 17

During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2b. O In this category, each of the game’s player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. As the Player Input Switches and Devices are activated, the Switch or Device activated is spelled out in the space indicated.

PLAYER INPUTS

SE CTYATE ALL PLAYER PHeUT WETCHES AND DEVICES MET TULF

Figure 3-2b Self-Test — Player Inputs

SELECT WH REPORT

CHUTE 1 CRIRS

cure @ CRITAS

LONGEST LAE

SHURTE GARE

HIGHEST SCARE

LOWEST SCORE

@rine BFPoAT

SEORE REPORT OW EALT

ah

ene

aN Eup: Suk BY waVING DLE bs tft OL. HA ) TRIGGER BUTTON FOR Test

Figure 3-2c Self-Test — Bookkeeping

3-3 During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2c. CO In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained.

In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 3-2d and 3-2e respectively.

TTRE REPORT

a0 SEC

GO SEE

TH GH GEE

SED

120 TH 250 SEE

i150 TH 180 SEL

a TH 4 HIW

“TH 5 WIN

§ TH 6 BIN

BVER 6 MIN a

au

bo a

Ta

an Th lea

PULL, TRIGGER BUTTON TA EX

Figure 3-2d Self-Test — Time Report

SORE

aro sane eT

Sona Th LAnn

1none TH Bono

Baonn TA HnOnEn

Woe TO Nn FI

wenn FO LApANO BTS

innoOn TH AsnHHA PTS

1s0n0n TH BNnAUe PTS

Banana ra eanNNe PTS

OVER asnooo ATS REPRE

PUL. THEGGER BUTTON TO EXLE

Figure 3-2e Self-Test — Score Report

Page 18

During the SETUP OPTIONS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2f.

C In this category, all common game options may be changed from the controi console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level - -, and so on.

COIN cH #91

COTW CH 4+ wh

CHEDETS FOR #9) BASES

ENTRA BARGE AT #10000 POINTS

*OLEF ghuury LEVEL *1

  • = Factory recommended settings.

Figure 3-2f Self-Test — Set-Up Options

DIFFICULTY LEVEL EXPLANATION: The Difficulty Level setting has a range of 1 to 9. With 1 being the easiest level of play and 9 being the most difficult level of play. We recommend that a setting of 4 be used as a beginning point. Game play can then be made MORE difficult or LESS difficult, according to the skill levels attained by the players in your area. CHANNEL TEST: During the CHANNEL TEST section of the Self-Test mode, the game wil! give a display which looks like that shown in Figure 3-2g. C1 In this category, the game conducts a test of its SOUND SYSTEM.

Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until the “SHIELD” button is hit. It then goes back to the Self-Test Mode Menue.

3-4 EHANHEL

CHANNEL

@CHANNE:.

CHANNEL

CHANNEL

CHAHMEL

CHANNEL

FRIGHER BUTTON TH EXTT

Figure 3-2g Self-Test — Channel! Test

During the GRID DISPLAY section of the Self-Test mode, the game showsa white cross hatch pattern on the monitor screen. This is for alignment and/or test Purposes. This pattern will remain on the monitor screen until the SHIELD Button is hit. The game will then go back to the Self-Test Mode Menue.

To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen. RACK ADVANCE:

The game can be made to advance through the various racks by beginning a game and THENsliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack.

When you reach the desired rack, slide the Self-Test switch to the “OFF” position. (If you leave the Self- Test switch in the “ON” position, the game will go into the Self-Test mode when you are finished playing the rack you “advanced” to.) CROSS HATCH PATTERN:

A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, and during the “SELF DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier.

When you are finished using the cross hatch pattern, simply hit the SHIELD Button to return to the Self- Test Mode Menue.

Page 19

HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 3-3. The function of each of these switches — when pressed — is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.

HARDWARE MASTER RESET SWITCH

Figure 3-3 Location of Hardware Master Reset Switch

ATTRACT MODE

  • The Attract mode starts:

O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) C) After a Self-Test has been completed and there are no more credits left in the game’s memory. O After a play has been finished, the score was not high enough to put the game into the High Score/initial mode, and there are no more credits left in the game's memory. O After the High Score/Initial mode when there are no more Credits left in its memory. C In the Attract mode, the game will give the following displays centered on the monitor screen: No matter where the game isin the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER" or the “2 PLAYER” start button is pushed. it FRERIT PEN PLAYER INSERT CHIN

  • CAPYREGMT MeL?

AALLY HLOWAY HEE fa

ALi RIGHTS REFERVED

CraeoITs a

Attract Mode Display 1

Page 20

= om E

c

cy e free Sn: <r

oaese game = ladet === BUILDING THE BHIDGE

BONUS

WU5 FLAG Ta Ae aaRE A BATTLE LETED

BOWS FLAG 5 10oa WDTT TAWA.

LECT THE BANA Panne BRIDGE inte ND GF SATAN HNO T SATAN

HE Arran £3 ED AN ADOLT LAN +4 A BPEe ra A ANTM

EREDITS 6

Attract Mode Display 2 Attract Mode Display 4

BRIDGE HUMBER

BRIDGE BOT aF TH BRIDGE THAT § BRIDLE WILL,

CREDITS 0

Attract Mode Display 3 Attract Mode Display 5

3-6

Page 21

BRIDGE BOMBER RE RABRER Be Opie RHEKT ROEK HET HE THAT SEE wee BE fr

CREDITS O

Attract Mode Display 6

SHIELD

THE GHTELO PROTECTS THE BHSE ALRINST

GARGOYLE

SHLELD 1@ CRERTITS O

Attract Mode Display 7 SHIELDS

THE & Ha PROTECT ore THE BASE RGAINST

BABS

SHEELO 08 CHEDTTS &

Attract Mode Display 8

SHXELO Fe ERERITS a

Attract Mode Display 9 ta

Page 22

SHEELD LE EREDTTS o

Attract Mode Display 10

SHIELD

FLAME

Ld aug ‘fi’ Rattle Hal Ve aH PELE

SHEED 29 EwEnETS a

Attract Mode Display 11 BRINE VALUES

SHTHH ati

LUE TFER Land

ALD BALK ann

REEL ZEQUB ean

ERG THRODER ees

BALOGE BNWREN ERS

GARGEYLE Leo CREATES

Attract Mode Display 12

RANKINGS

EL Bha1D

ee aan

We 48945

4SGEn

a4as

aeesn

a0ne0

eg885

enpao

eave

&

CREDITS 8

Attract Mode Display 13

Page 23

READY-TO-PLAY

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a-.2 player game.
  • The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.

44T ena i HTL ORE HE910

PER PURYER 4 CREDIT

FOR BIRECTIONS

HIT FHTELD BUTTON

TO START GANE

PRESS L PLAYER

hb

fn pEROaSTT

MORE CHING FoR

PLAYERS

ener

Ready to Play Mode Display 1

PLAY MODE

  • The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. When this happens, the following is displayed centered on the monitor screen.

BONUS BASE AWARDED

AT *10000 POINTS

= (* = switch selectable)

Play Mode Display #1

3-9

  • In the Ready-To-Play mode, the game will give the following displays centered on the monitor screen.
  • If no START button is pressed, the game will hold the following “Instruction Message” display on the screen indefinitely.

ast eno a HISEORE @6510 i

4 CREDIT PER PLAYER

FOR DIRECTIONS

HIT SHIELD BUTTON

TO START GHAE

PRESS 1 PLAYER

ay ay ah OR PUGH

@ PLAYERS ty ay ay CREDITS &

Ready to Play Mode Display 2

  • The Play mode. ends when you have no more Missile Launchers left to fire at your attackers. When this happens, the following is displayed centered on the monitor screen.

“GAME OVER” “PLAYER” “YOUR SCORE” “RANKING IS”

Play Mode Display #2

Page 24
  • The game is made up of attackers displayed across the monitor screen in phases called “racks”. These attackers will try to destroy your Missile Launcher. What form the attackers will come in depends on what rack you are in.

The racks are made up of different kinds of attackers and varying numbers of each type. The higher the rack number, the greater are the numbers of certain types of attackers present. In the earlier racks the attackers are easier to overcome

than in the more advanced ones. A list of the

various attackers and what they do follows. GARGOYLE: This is a green, fire-breathing, birdlike creature. It will drop bombs on, and/or dive at your Missile Launcher. \f your Missile Launcher is hit by either, it will be destroyed. BRIDGE BOMBER: This is a red, fire breathing, bird-like creature. It carries large rocks that it will try to drop on your Missile Launcher and/or the Bridge you're building. Failing this, it will try to crash into your Missile Launcher. If it is hit by a rock or crashed into by a Bridge Bomber, your Missile Launcher will be destroyed. lf your Bridge is hit by a rock, the section(s) that were hit will be knocked out. You then have to replace it (them) BEFORE you can continue work on the completion of the rest of your Bridge. EGG THROWER: This is a green devil-like creature. It carries large explosive Eggs which it will throw at your Missile Launcher to try to destroy it. It will also try to crash into your Missile Launcher if it hasn’t been hit by one of the exploding and burning Eggs. When these Eggs hit the ground, they explode and burn quite fiercely for several seconds each. You can move your Missile Launcher through the fire(s) they cause ONLY if it's SHIELD is up. Otherwise it would be destroyed. ALL OF THE ABOVE ARE THOROUGHLY NASTY

  • you really have to keep an eye on them! Among the other sneaky things they do, they will try to STEAL your RESERVE Missile Launchers. But, if you shoot the one that is carrying off your reserve Missile Launcher BEFORE it reaches the top of the screen and disappears, you will get this particular stolen Missile Launcher back. Don’t relax your guard though, because they will keep trying to steal them.

If the Missile Launcher you are currently using is destroyed in the attempt to save the one that was stolen BEFORE it reaches the top of the screen and disappears, that stolen Missile Launcher will be returned to you. LUCIFER, OLD NICK, and BEELZEBUB: These are all red devil's head characters. LUCIFER is the smallest in size. The others are each slightly larger than the previous figure — respectively. LUCIFER appears 1st. If you can’t hit him with a missile and he doesn’t barbecue you, OLD NICK appears next (he’s slightly larger in size presenting a bigger target) and will try to destroy your Missile Launcher in the same way. If you survive his attempts on you, BEELZEBUB will appear in his turn — and so on.

If, by some miracle, you manage to escape “barbecue time” but were unable to destroy any of the devil’s head characters, the next rack of green attackers (GARGOYLES, EGG THROWERS, etc.) will appear after the last devil's head character disappears. . MISSILE LAUNCHER SHIELD: Your MISSILE LAUNCHER is equipped with a SHIELD that can protect it from ANYTHING in the game that is capable of destroying it. However, this SHIELD only lasts for a VERY SHORT TIME if it is used continuously (about 1 second). So use iisparingly! As soon as you release the SHIELD Button, it begins to recharge at a rate roughly equal to the speed it discharges at when you use it. MISSILE LAUNCHER DESTROYED: Whenever you lose a Missile Launcher, assuming you have one in reserve to replace it with, the replacement will have ONE LESS Missile Launcher Barrel than your previous one had down to a MINIMUM of one. You will ALWAYS have AT LEAST one Missile Launcher Barrel on your Missile Launcher at all times.

. GAME PLAY: This is a short description of the object of the game, how to play it, and what happens when you do. OBJECT OF THE GAME: Is to destroy your attackers while at the same time preventing them from destroying you. When any attacker is destroyed, a Bridge Section will appear at the lower left hand corner of the screen.

You can pick up this Bridge Section with your Missile Launcher and place it at the edge of the Devil’s Gorge (eventually building a bridge completely across it, allowing you to enter SATAN’S HOLLOW). No matter how many attackers you destroy, another Bridge Section WILL NOT appear until AFTER the current one is in place over the Devil’s Gorge. END OF A RACK — LAST ATTACKER DE- STROYED: When the last attacker of any rack is destroyed, the action stops and a green bird flies to the castle with a white flag. BATTLE WITH SATAN: Once you complete the construction of your Bridge across the Devil's Gorge, you can cross it and enter SATAN’S HOLLOW. If you defeat SATAN, you gain an additional Missile Launcher Barrel (more fire power). The maximum number of Missile Launcher Barrels allowed is 3 per Missile Launcher. No matter how

Page 25

many times you do battle with, and defeat SATAN, you CANNOT obtain more than 3 Missile Launcher Barrels on your current Missile Launcher. Once you've received your 3rd Missile Launcher Barrel, your additional incentive to build another Bridge is that whenever you cross into SATAN’S HOLLOW, do battle with him, and defeat him, you are awarded BONUS POINTS for each flag on the castle. (As mentioned elsewhere, you earn one flag for each complete rack of attackers you destroy.) As you improve your skills and become better and better at the game, advancing into the more difficult racks, you will see more and more of the BRIDGE BOMBERS and EGG THROWERS per rack. Regardless of how it happens, when one of your Missile Launchers is destroyed, assuming you have at least one more remaining in reserve, your new Missile Launcher will appear in the bottom center of the monitor screen and play begins anew. When your LAST Missile Launcher is destroyed, the words below are displayed centered on the monitor screen.

“BAME OVER” AYER ‘OUR SCORE” “RANKING 1S"

3-11 If your score was high enough to become one of the ten best scores, the game will go into the High Score/Initial mode immediately after the above display. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready- To-Play mode (if there are still credits left in its memory). In the High Score/Initial mode the game gives a display which looks like the following:

PLEASE ENTER: YOUR.INITIALS A B C Q E

& t— I

K b i N o e § R $ T U v WwW Xx ¥

By moving the control stick to the right, you can make the cursor move down the alphabet: “A”, “B”, “Cc”, “D”, etc. By moving the control stick to the left, you can make the cursor move up the alphabet: 2", °Y", "X", “W", etc. When you reach your initial, center the control stick and pull the trigger. Your initial is printed out on the screen. If you do not wish to put your initials opposite your score, just pull the trigger two times. Two “A”’s will appear on the screen. Or — you can push either the 1 or 2 PLAYER button to leave this mode immediately.

NOTE: If you make a mistake, you can erase the wrong letter by positioning the cursor opposite the “ERASE” word at the bottom of the line of alphabet characters and pressing the trigger. Then simply go back and print out the correct letter. When you've printed out your last initial, move the cursor opposite the “END” word and pull the trigger to tell the game you are through printing out your initials. The game will then give the following RANKINGS display showing your score opposite your ranking and your initials.
Page 26

RANKINGS

HG410.

S58 10

4HaLS

49960 SNR.

aeesn et

Ep.

ne

angen

eens

eubSn

CCM

CHEBTTS

NOTE: If you don't tell the game you are through printing out your initials as instructed above, the game will automatically go into the RANKINGS. display after a short wait. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To- Play mode (if there are still credits left in its memory).
  • Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. in the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.

  • In the Upright and Mini models, the players must take turns at the controls. . In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of controls will have NO effect on the game.) . Your turn lasts until your Missile Launcher is destroyed. At this point, the game will do one of several things depending on whether or not the destroyed Missile Launcher was your last one or.if you still have others remaining in reserve.

3-12 DESTROYED MISSILE LAUNCHER — OTHERS REMAINING IN RESERVE O The game stops and “PLAYER UP” is displayed on the monitor screen. O Next, the other player’s Missile Launcher and attackers appear on the screen and game play begins for the other player.

DESTROYED MISSILE LAUNCHER — NO OTHERS REMAINING IN RESERVE O Game displays:

“GAME OVER” “PLAYER” “YOUR SCORE” RANKING 1S”

centered on the monitor screen. After the above display, if your score was high enough, it goes to the “HIGH SCORE/INITIAL” mode. After this mode, “PLAYER UP” and the other player's Missile Launcher and attackers appear on the monitor screen. Play then begins for the other player. If your score was NOT high enough to cause the game to go into the “HIGH SCORE/INITIAL” mode, the game will just display “PLAYER —__ UP", the other player’s Missile Launcher and attackers on the monitor screen. Play then begins for the other player.

Page 27

IV. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should: remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING

The outside of the game cabinet plus the metal canbe cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
  • MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Supply Chassis and the Power Supply P.C. Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

FUSES LOCATED ON POWER SUPPLY BOARD AND POWER SUPPLY CHASSIS.

Figure 4-1 Location of Fuses

Page 28

OPENING THE CONTROL PANEL 1, UPRIGHT MODEL: See Figure 4-2. 0 The control panel is held in place by two latches,

  • MINI MODEL: See Figure 4-2. O The control panel is held in place by two latches,

o

o one on the left side and one on the right side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt ittoward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. To reinstall the control panel, reverse this procedure.

UPRIGHT LATCHES one on the right side, and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed.

O To reinstall the contro! panel, reverse this procedure.

Figure 4-2 Opening the Control Panel — Upright & Mini

4-2

Page 29

Figure 4-3 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 4-4. D Each control panel is held in place by several screws, four on the inside of the cabinet and three along the inside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-3.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 4-4. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.

4-3 LIFT CONTROL UP

REMOVE

  • SCREWS , EACH SIDE

REMOVE(3) SCREWS

Figure 4-4 Removing the Control Panel — Cocktail

Page 30

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY

  • UPRIGHT MODEL: See Figure 4-5.
NOTE: In order to do this, the control pane| MUST be removed first. See the “Upright Model” procedure.

0 Turn the power to the game off and remove the control panel. This gets the control panel stick out of the way so the main-display-glass can be removed. Remove the screws securing the main-displayglass retainer and the main-display-glass in place as shown in Figure 4-5 and lift out the main-display-glass. Remove the screws which secure the T.V. bezel assembly in place. The T.V. bezel assembly is now free and can be slid out of the cabinet. O To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure. oOo

ia

DISPLAY GLASS

CLAMPING PLATE

Figure 4-5 Removing the Main Display Glass & T.V. Bezel — Upright

4-4

  • MINI MODEL: See Figure 4-6.
NOTE: In order to do this, the control panel MUST be removed first. See above “Mini Model” procedure. O Turn the power off to the game and remove the control panel. O Remove the screws which secure the glass clamping plate. See Figure 4-6. O Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up.and out. O Remove the screws which secure the T.V. bezel assembly and lift it out.
NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. O Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.

DISPLAY GLASS

GLASS CLAMPING PLATE

Figure 4-6 Removing the Main Display Glass & T.V. Bezel — Mini

Page 31

. COCKTAIL TABLE MODEL: See Figure 4-7.

NOTE: This may be done with the table top in the closed or the open position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. O Remove the screws which secure the table top glass clamps in place. O Remove the table top glass. (Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. C To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure.

Figure 4-7 Removing the Top Glass & T.V. Bezel

  • Mini T.V. MONITOR REPLACEMENT
CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and7do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.
  • UPRIGHT MODEL: See Figure 4-8. 0 Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Upright Model” procedure. O With the removal of only four bolts, the T.V. monitor and its mounting bracket will be loose. O The monitor mounting bracket slides on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.

MINI MODEL: See Figure 4-9. O Turn the power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel! MUST be removed. See. above “Mini Model” procedure. O With the removal of only four bolts, the T.V. : monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so It will not fall out of the cabinet.

4-5

Page 32

O The monitor is removed by supporting it and pulling straight back. (BE CAREFUL not to hit monitor on its rear support bracket.) O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.

  • COCKTAIL TABLE MODEL: See Figure 4-11. 0 Turn the power off to the game. O Open the coin box door and release the two latches indicated in Figure 4-10.

, REMOVE (4) BOLTS

Figure 4-8 Removing the Monitor — Upright

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

O Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-10.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

~ REMOVE (4) BOLTS

Figure 4-9 Removing the Monitor — Mini

Page 33

CLAMPS

Figure 4-10 Opening the Cocktail Game

O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. DB Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. : O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-11, O Close the Cocktail Table and re-latch it. © Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-11. Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. O Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube. U To reinstall the T.V. monitor assembly, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

REMOVE 4 SCREWS ._ (2 EACH SIDE) N

Figure 4-11 Removing the Monitor — Cocktail

Page 34

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 4-12. O Turn the power to the game off. O To reinstall the above P.C.B.’s, reverse this procedure. O Unlock and open the rear access door. 0 Disconnect ail cabling from the P.C. boards and NOTE: P.C.B.’s are all keyed and will ONLY fit lift them out of their card rack.. into their connectors one way without forcing them. The plugs on the cable harness which O Disconnect the linear power supply board from connect it to the P.C.B.’s are also keyed and will all its cabling, remove the P.C.B. supports indi- bi cated in Figure 4-12, and slide the linear power batalla thelr:connectors one way without supply board out the back of the cabinet.

\

J REMOVE (2) SUPPORTS Ma

COCKTAIL REMOVE REMOVE SUPPORT SUPPORT

UPRIGHT

Figure 4-12 Removing P.C.B.’s

4-8

Page 35

REMOVE SCREWS FROM SIDE OF CABINET TO REMOVE LOGIC BOARDS

Figure 4-13 Removing P.C.B.’s from Card Rack

  • MINI MODEL: See Figure 4-12. O Turn the power off to the game. D Unlock and open the rear access door. D Disconnect all cabling from the P.C. boards and lift them out of their card rack. 0 Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-12, and slide the linear power supply board out the back of the cabinet. 0 To reinstall the above P.C.B.’s, reverse this procedure.
  • COCKTAIL TABLE MODEL: See Figure 4-12. © Turn the power off to the game. Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-10.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on BE CAREFUL! the monitor.

Once they’re released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-10.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

OD To remove the linear power supply board. See Figure 4-12. Disconnect it from ail its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. O1'To remove the P.C. boards from the card rack. See Figure 4-13. Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack. O To reinstall the P.C. boards, procedure. reverse this

Page 36

OPENING THE ATTRACTION PANEL

  • UPRIGHT MODEL: See Figure 4-14. REMOVE SCREWS ON TOP AND LIFT ATTRACTION PANEL UP O Turn the power to the game off. O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 4-14. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can tly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

OD Replacing the fluorescent tube starter. See Figure 4-15. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. OD Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out of the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. D Replacing the speaker. Be sure the power is off to the game. Figure 4-14 Opening the Attraction Panel — Upright Remove the attraction panel and disconnect the speaker from its cabling. 2. MINI MODEL. See Figure 4-16. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them 1 Tum the power off to the game. and the speaker grill aside. O Remove the screws which secure the top Once the bolts which secure the speaker in bracket in place. (They are on its top side.) See place are removed, the speaker may be re- Figure 4-16. moved through the opening where the attrac- 0 Remove the top bracket and slide up the attraction panel was. tion panel. This exposes the attraction panel Reverse this procedure to reinstall the speaker. light bulbs and their mounting board.

4-10

Page 37

weoo™ FLUORESCENT TUBE STARTER 1/4 TURN TO REPLACE

Figure 4-15 Replacing Fluorescent Tube Starter

C To service the light bulbs and their mounting board: REMOVE TOP Turn the power to the game back on so youcan BRACKET AND see which bulbs are burnt out. SLIDE HEADER UP Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gentiy pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cabie. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL. Figure 4-16 Opening the Attraction Panel — Mini

att

Page 38

SERVICING THE CONTROL PANEL BLACK LIGHT (UPRIGHT MODEL ONLY)

  • Be sure the power is off to the game.
  • Remove the control panel as described previously. This exposes the bottom row of screws which secure the control panel support bracket and the black light protector in place. See Figure 4-17.
  • Remove all the screws which secure the above items in piace and set them aside. O The black light tube may be replaced at this time by reaching through the space where the light protector was before you removed it.
WARNING: If you drop a black light tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any black light tube.
  • Replacing the black light tube starter. See Figure 4-15. O Remove the black light tube. Remove the screws which secure the black light tube mounting bracket to the cabinet. See Figure 4-18. The mounting bracket is now loose and can be pulled out and slightly to one side until you can see the black light tube starter. 0 Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the black light tube starter, reverse this procedure.

REMOVE THESE SCREWS

Figure 4-17 Servicing Control Panel Black Light — Upright

  • The black light tube mounting bracket assembly may be replaced at this time by simply disconnecting it from its power cable and removing it from the game.
  • To reinstall any of the above removed items, simply reverse this procedure.

Figure 4-18 Removing Black Light Tube Mtg. Brkt.

  • Upright

BLACK LIGHT PROTECTOR

CONTROL PANEL SUPPORT BRACKET

4-12

Page 39
Scan of page 39

This page is a drawing, shown as the original scan.

Page 40

5-2 NO. 941 — SATAN’ ’S HOLLOW

  • UPRIGHT — FRONT
Page 41

NO. 941 — SATAN’S HOLLOW — UPRIGHT — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY | rem | PART NO. DESCRIPTION 0941-00902-00XF DECORATIVE HEADER PLEXI 0537-00903-0063 GLASS CHANNEL — 6-3/8" LG. (2 REQ’D.) 0574-00903-0100 HEADER BRKT. RETAINER (2 REQ'D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ’D) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A595-00011-0000 HEADER LIGHT ASSY. 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ'D.) 0077-00003-0430 6" x 9” SPEAKER — 4 OHM, 10W. (2 REQ'D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0508-00900-0000 19” T.V. BEZEL 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ'D.) 0017-00101-0017 #6 x 1/2 SLT. HEX HD. BLACK SCREW (4 REQ’D.) 0941-00901-00XF MAIN VIEWING GLASS 0941-00102-00XF HOLD DOWN BRKT. 0017-00101-0126 #10-32 x 3/4 BLK. BUTTON HD. SCR. (4 REQ'D.) 0941-00903-0000 LAMP PROTECTOR 0017-00101-0088 #8 x 3/4 PHIL. FLAT HD. SCR. (3 REQ’D.) A628-00009-0000 CONTROL SHELF LIGHT ASSY. — UPPER 0628-00916-0000 MIDDLE FLUORESCENT REFLECTOR 0941-00900-0000 CONTROL SHELF OVERLAY — DECORATIVE 0941-00101-0000 CONTROL SHELF PLATE 0941-00103-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0941-00103-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ'D.) 0982-00102-0000 STRIKE (2 REQ'’D.) 0017-00009-0534 BASSICK CLAMP (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (12 REQ’D.) A941-00021-0000 CONTROL ASSEMBLY A089-00020-0000 CONTROL GRIP CABLE ASSY. — 16” A941-00011-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0256 PUSH BUTTON ASSY. — RED (2 REQ’D.) 0017-00042-0257 PUSH BUTTON ASSY. — YELLOW (2 REQ'D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ’D.) A090-00300-11BK U.S.A. 25¢ COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23" LG. 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

Page 42

v-S \oe ee | noe a — Eirias prestesnapeememicsnenionncy Lae a — i ag ee pe oe] P| Pc ee nea oes eee PERE SS3909V YV4Y — LHDIYdN — MOTIOH S.\NVLVS — LP6 ‘ON

Page 43

NO. 941 — SATAN’S HOLLOW — UPRIGHT — REAR ACCESS — PARTS LIST

PART NO.

A088-00013-0000 0894-00916-G000 0017-00101-0141 0941-00106-0000 0017-00101-0027 0508-00900-0000 0508-00106-0000 0508-00901 -0000 0017-00101-0017 0017-00003-0339 ORDER BY PART NUMBER ONLY

DESCRIPTION

ON-OFF SWITCH & BRKT. ASSY. PLASTIC PULL & VENT (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) MAIN VIEWING GLASS STOP BRKT. #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.) 19" T.V, BEZEL BEZEL MTG. BRKT. (2 REQ’D.) PLEXI-GLASS CLIPS (4 REQ’D.) #6 x 1/2 SLT. HEX HD. BLACK SCREW (4 REQ’D.) ELECTROHOME — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR MONITOR MTG. CHANNEL ASSY. (2 REQ’D.) 1/4-20 x 3/4 UNSLOT. HEX BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ'D.) MONITOR RAIL (2 REQ'D.) INTERLOCK SWITCH & BRKT. ASSY. POWER SUPPLY P.C. BRD. ASSY. P.C. SUPPORT BRKT. — 6-1/2" LG. (4 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. SCR. (8 REQ’D.) #8 WASHER (8 REQ’D.) DUAL POWER ANP P.C. ASSY. 1/8” SNAP BUSHING (4 REQ'D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D.) POWER CHASSIS ASSY. — 125VA., 115V. CARD RACK W/BOARDS ASSY. C.P.U. P.C. BOARD ASSY. SOUND P.C. BOARD ASSY. i. VIDEO/GENERATOR P.C. BOARD ASSY. 1-1/8" P.C.B. SUPPORT (4 REQ’D.) DUAL LKG. P.C.B. SPACER (4 REQ'D.) #6 x 5/16 SLT. HEX HD. WD. SCR. (4 REQ’D.) COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ'D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ'D.) 1/4-20 HEX NUT (4 REQ’D.) CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ’D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8” E-RING (2 REQ'D.) LINE CORD ASSY. — 115V. ITEM

0017-00003-0439

A508-00005-0000 0017-00102-0066 0017-00104-0014 0595-00104-0000 A088-00016-0000 A082-90412-D000 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-90910-E000 0017-00042-0014 0017-00101-0751 A945-00020-0000 A941-00004-0000 A084-90010-A941 A084-90913-A941 A084-91399-A941 0017-00042-0208 0017-00042-0253 0017-00101-0085 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A961-00007-0000 0961-00109-0000 0017-00042-0255 (0894-00702-00XF 0017-00100-0037 A945-00019-0000

5-5

Page 44

NO. 941 — SATAN’S HOLLOW — UPRIGHT — REAR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

ADDITIONAL PARTS LIST

A151-00098-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILL — BACK DOOR (4 REQ'D.) A515-00021-0000 MULTIFUNCTION SWITCH & BRKT. ASSY. A515-00020-0000 TEST SWITCH & BRKT. ASSY. A941-00015-0000 MASTER CABLE W/BRKT. ASSY. A941-00007-0000 HIGH VOLTAGE CABLE ASSY. A941-00008-0000 LOW VOLTAGE CABLE ASSY. A968-00029-0000 VIDEO SIGNAL CABLE ASSY. 0017-00009-0513 1/8" T-HANDLE ALLEN KEY

Page 45

NO. 941 — SATAN’S HOLLOW — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.

NO. 941 — SATAN’S HOLLOW — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST

ITEM PART NO.

0595-00105-0000 0017-00003-0043 0017-00003-0445 0017-0003 1-0036 0017-00003-0412 0017-00101-0573 0017-00104-0009 0017-00003-0019 0017-00003-0026 0017-00101-0598 A961-00042-0000 ORDER BY PART NUMBER ONLY

DESCRIPTION

FLUORESCENT BRKT. 18" COOL WHITE FLUORESCENT LAMP LAMP LOCKS (2 REQ’D.) FLUORESCENT SOCKET (2 REQ’D.) FLUORESCENT STARTER HOLDER W/LEADS #6-32'x 1/2 PHIL. RND. HD. MS. (4 REQ'D.} #6 EXT. WASHER (4 REQ’D.) FLUORESCENT STARTER BALLAST #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.} LINE FILTER ASSY.

5-7

Page 46

NO. 943 — SATAN’S HOLLOW — MINI — FRONT

5-8

Page 47

NO. 943 — SATAN’S HOLLOW — MINI — FRONT ~- PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0943-00901-00XF DECORATIVE HEADER 0537-00903-0062 GLASS CHANNEL — 3-7/8" LG. (2 REQ'’D.) 0574-00100-00XF HEADER BRKT. RETAINER (2 REQ'D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (6 REQ’D.) 0077-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A926-00010-0000 INSERT DISPLAY ASSY. A514-00015-0000 INSERT CABLE ASSY. 0017-00031-0030 WEDGE BASE LIGHT SOCKET (5 REQ'’D.) 0017-00003-0219 #194 WEDGE LAMP — 14V., .27A. (5 REQ'D.) 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ’D.) 0017-00003-0430 6" x 9" SPEAKER — 4 OHM, 10W. (2 REQ'’D.) 0017-00101-0127 #8-32 x 1-1/2" CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0943-00900-00XF MAIN VIEWING GLASS 0537-00903-0056 GLASS CHANNEL — 14-1/2” LG. (2 REQ’D.) A555-00016-0000 GLASS CLAMPING PLATE ASSY. 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (2 REQ'D.) 0943-00902-0000 DECORATIVE CONTROL SHELF OVERLAY A943-00015-0000 CONTROL SHELF WELD PLATE ASSY. 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. —~ LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ’D.) 0982-00102-0000 STRIKE (2 REQ'D.) 0017-00009-0534 BASSICK CLAMP (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (12 REQ'’D.) A941-00021-0000- CONTROL ASSEMBLY A089-00020-0000 CONTROL GRIP CABLE ASSY — 16” A943-00011-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0256 PUSH BUTTON ASSY. — RED (2 REQ'D.) 0017-00042-0257 PUSH BUTTON ASSY. — YELLOW (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ’D.) A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) 0935-00906-0400 KICK PLATE — 17-15/16" LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

Page 48
  • MINI — REAR ACCESS ’S HOLLOW NO. 943 — SATAN

5-10

Page 49

NO. 943 — SATAN’S HOLLOW — MINI — REAR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0017-00003-0430 6” x 9" SPEAKER — 4 OHM, 10W. (2 REQ’D.) 0513-00900-0000 TV. BEZEL A961-00026-0000 BEZEL MTG. BRKT. ASSY. (2 REQ’D.) 0017-00003-0340 ELECTROHOME — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR T.V. MTG. BRKT. ASSY. 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (2 REQ’D.) 7/8" DISH WASHER (2 REQ’D.) MONITOR MTG. BRKT. INTERLOCK SWITCH & BRKT. ASSY. U.S.A. 25¢ DOUBLE COIN DOOR ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 BLACK RHD. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ'D.) 1/4-20 HEX NUT (4 REQ’D.) POWER SUPPLY P.C. BRD. ASSY. P.C. SUPPORT BRKT. — 6-1/2" LG. (4 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. SCR. (8 REQ’D.) #8 WASHER (8 REQ'D.) DUAL POWER AMP P.C. ASSY. 1/8” SNAP BUSHING (4 REQ’D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D.) POWER CHASSIS ASSY. — 125VA., 115V. CARD RACK W/BOARDS ASSY. C.P.U. P.C. BOARD ASSY. SOUND P.C. BOARD ASSY. ViDEO/GENERATOR P.C. BOARD ASSY. 1-1/8" P.C.B. SUPPORT (4 REQ’D.) DUAL LKG. P.C.B. SPACER (4 REQ'D.) #6 x 5/16 SLT. HEX HD. WD. SCR. (4 REQ'D.) ON-OFF SWITCH & BRKT. ASSY. LINE CORD ASSY. — 115V. ITEM

0017-00003-0435

A926-00012-00XF 0017-00102-0066 0017-00104-0014 0513-00101-0000 A088-00016-0000 A090-00300-11BK A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00900-0000 0017-00101-0142 0017-00104-9014 0017-00103-0018 A082-90412-D000 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-90910-E000 0017-00042-0014 0017~00101-0751 A945-00020-0000 A941-00004-0000 A084-90010-A941 A084-90913-A941 A084-91399-A941 0017-00042-0208 0017-00042-0253 0017-00101-0085 A088-00013-0000 A945-00019-0000

ADDITIONAL PARTS LIST

BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILL (4 REQ'D.) PROTECTIVE BUBBLE — BACK DOOR #8-32 x 3/4 CARRIAGE BOLT (10 REQ'D.) #8-32 HEX NUT W/SEMS (10 REQ’D.) TEST SWITCH & BRKT. ASSY. MASTER CABLE W/BRKT. ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. VIDEO SIGNAL CABLE ASSY. A151-00098-0000 0017-00009-0490 0926-00904-0000 0017-00101-0628 0017-00103-0061 A515-00020-0000 A943-00014-0000 A943-00008-0000 A943-00009-0000 A968-00029-0000

Page 50

NO. 941 & 943 — SATAN’S HOLLOW — UPRIGHT & MINI — CONTROL ASSY.

5-12

Page 51

NO. 941 & 943— SATAN’S HOLLOW — UPRIGHT & MINI — CONTROL ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0873-00900-0200 CONTROL GRIP — LEFT 0873-00900-0100 CONTROL GRIP — RIGHT 0941-00904-0000 LENS 0628-00906-0000 TRIGGER A628-00028-0000 CONTROL GRIP SWITCH ASSY. 0020-00202-0000 SWITCH PLATE 0017-00101-0528 #5-40 x 3/4 PHIL. RND. HD. M.S. (2 REQ’D.) 0873-00123-00XF SWITCH MTG. BRKT. 0017-00101-0083 #4-20 x 3/8 PHIL. PAN HD. SCR. (2 REQ’D.) 0017-00101-0149 #10-32 x 3/8 TORX TAMPER RESISTANT BUTTON HD. SCREW (5 REQ’D.) 0941-00700-00XF GRIP TUBING 0628-00904-0000 SLIDE A941-00024-0000 CONTROL BRKT. & BEARING ASSY. 0941-00905-0000 BUMPER (2 REQ’D.) 094 1-00704-O0XF SPACER (2 REQ'’D.) 0017-00101-0668 #10-32 x 1” HEX SOCKET HD. CAP SCR. (2 REQ'’D.) 0017-00104-0004 #10 SPLIT LOCK WASHER A089-00020-0000 CONTROL GRIP CABLE ASSYV. — 16” LG. 0010-00266-0100 SPRING EXTENSION STRAIN RELIEF 0017-00021-0299 2 PIN CONNECTOR A941-00019-0000 BUSHING & BEARING BRKT. ASSY. 0017-00101-0646 #10-32 x 1/4 SLT. PAN HD. SCR. W/SEMS (4 REQ'D.) 0942-00702-00XF PIVOT PIN 0017-00100-0025 1/4” E-RING (2 REQ'D.) 0941-00108-0000 SWITCH BRKT. 0017-00101-0085 #6 x 5/16 SLT. HEX HD. SCR. (3 REQ'D.) A941-00022-0100 ROLLER SWITCH ASSY. — LEFT A941-00022-0200 ROLLER SWITCH ASSY. — RIGHT 0020-00202-0000 SWITCH PLATE (2 REQ'D.) 0017-00101-0527 #5-40 x 5/8 PHIL. RND. HD. SCR. (4 REQ'D.) 094 1-00109-0000 SWITCH ACTUATOR 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (2 REQ'D.) 094 1-00703-00XF SPRING PIN 0017-00100-0018 3/16" E-RING 0010-00602-0000 EXTENSION SPRING 0017-00042-0316 SHOULDER WASHER 0017-00101-0622 #8-32 x 1/2 HEX HD. SOCKET SCREW (LOCATED ON ITEM #7)

5-13

Page 52

5-14 NO. 942 — SATAN’S HOLLOW — COCKTAIL — FRONT

Page 53

NO. 942 — SATAN’S HOLLOW — COCKTAIL — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

0017-00009-0499 COVER GLASS — 32” x 22” x 1/4" 0942-00900-0000 ARTWORK UNDERLAY — DECORATIVE 0775-00104-00XF GLASS CLIPS (8 REQ’D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCREW (8 REQ'D.) 0530-00903-0000 ACRYLIC DIFFUSER 0508-00901 -0000 PLEXI-GLASS CLIPS (4 REQ’D.) 0017-00101-0017 #6 x 1/2" SLT. HEX HD. BLK. SCREW (4 REQ’D.) 0557-00900-0000 T.V. BEZEL A942-00004-0100 CONTROL SHELF ASSY. — PLAYER #1 A942-00004-0200 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ'’D.) 0017-00009-0482 SMALL SPEAKER GRILL (2 REQ'D.) 0017-00003-0460 4” SQR. SPEAKER — 4 OHM, 10W. (2 REQ’D.) 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (16 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (16 REQ'’D.) A090-00300-11BK COIN DOOR ASSY. — U.S.A. 25¢ A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) A927-00019-0000 COIN BOX ASSEMBLY A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

5-15

Page 54

NO. 942 — SATAN’S HOLLOW — COCKTAIL — INTERIOR ACCESS

=

5-16

Page 55

NO. 942 — SATAN’S HOLLOW ~— COCKTAIL — INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY [item | PART NO. DESCRIPTION 0610-00132-00ZN STRIKE (2 REQ’D.) 0017-00069-0534 BASSICK CLAMP (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) 0017-00003-0439 WELLS-GARDNER — 19" COLOR DUAL SYNC HORIZ. MTG. MONITOR A515-00019-0000 MONITOR SUPPORT ASSY. — LEFT A515-00019-0100 MONITOR SUPPORT ASSY. — RIGHT 0017-00101-0109 #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ’D.) 0942-00102-0000 POWER CHASSIS MTG. BRKT. (2 REQ’D.) 0927-00101-O00XF SUPPORT ANGLE (2 REQ'D.) 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. M.S. (8 REQ’D.) 0017-00009-0514 2-1/2" HINGE (2 REQ'D.) 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) A942-00013-0000 CONTROL PANEL WELDMENT ASSY. (2 REQ'D.) 0942-00901-0100 DECORATIVE OVERLAY PLAYER #1 0942-00901 -0200 DECORATIVE OVERLAY PLAYER #2 0510-00101-00XF BOTTOM PAN (2 REQ’D.) 0017-00101-0341 #6 x 1/4 PHIL. TRS. HD. SCR. (6 REQ'D.) A942-00018-0000 CONTROL ASSY. (2 REQ'’D.) A942-00005-0100 CONTROL SHELF CABLE ASSY. — PLAYER #1 A942-00005-0200 CONTROL SHELF CABLE ASSY. — PLAYER #2 0017-00032-0051 SMALL RED BUTTON SWITCH ASSY. W/HARDWARE (2 REQ'D.) 0017-00042-0301 PUSH BUTTON ASSY. — YELLOW (2 REQ'D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ’D.) 0930-00104-0000 CONTROL PANEL LOCATING BRKT. (4 REQ’D.) 0017-00101-0025 #8 x 1/2 SLT. HEX HD. M.S. (16 REQ’D.) 0727-00901-0000 LIGHT SHIELD (2 REQ'D.) 0017-00031-0044 WEDGE BASE LAMP SOCKET (4 REQ’D.) 0017-00003-0219 #194 WEDGE LAMP — 14V., .27A. (4 REQ'D.) 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ'D.} A082-90412-D000 POWER SUPPLY P.C. BARD. ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (7 REQ'D.) 0017-00104-0037 #8 WASHER (7 REQ'D.) A082~90910-E000 DUAL POWER AMP P.C. ASSY. 0017-00042-0014 1/8” SNAP BUSHING (4 REQ’D.) 0017-00101-0751 #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D.) A945-00020-0000 POWER CHASSIS ASSY. — 125VA., 115V. A941-00004-0000 CARD RACK W/BOARDS ASSY. A084-90010-A941 C.P.U. P.C. BOARD ASSY. A084-90913-A941 SOUND P.C. BRD. ASSY. A084-91399-A941 VIDEO/GENERATOR P.C. BOARD ASSY. 0017-00042-0208 1-1/8" P.C.B. SUPPORT (4 REQ'’D.) 0017-00042-0253 DUAL LKG. P.C.B. SUPPORT (4 REQ’D.) 0017-00101-0085 #6 x 5/16 SLT. HEX HD. WD. SCR. (4 REQ'D.)

Page 56

NO. 942 — SATAN’S HOLLOW — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

A775-00013-0000 FAN ASSEMBLY 0151-0008 1-0000 4” FAN 0775-00110-O00XF FAN PLATE 0749-00106-O0XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2 R.H.M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ'D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. M.S. (4 REQ’D.)

ADDITIONAL PARTS LIST A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. A942-00012-0000 MASTER CABLE W/BRKT. ASSY. A942-00009-0000 HIGH VOLTAGE CABLE ASSY. A942-00008-0000 LOW VOLTAGE CABLE ASSY. 580-0001 1-0000 VIDEO SIGNAL CABLE ASSY. 0942-00902-0000 MONITOR SHIELD A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL

NO. 942 — SATAN’S HOLLOW — COCKTAIL — CONTROL ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A727-00020-0000 KNOB & SWITCH ASSY. 0010-00267-0000 COMPRESSION SPRING 0017-00032-0103 PUSH BUTTON SWITCH — 115V., 1/2A. 0017-00101-0786 #2 x 5/16 PHIL. RND. HD. SCREW 0727-00904-0000 TRIGGER 0017-00007-0067 3/32 x 3/4 ROLL PIN 0017-00101-0148 #8-32 x 1/4 TAMPER RESISTANT TORX SCREW (2 REQ'D.) A942-00017-00XF CONTROL SWITCH BRKT. & TOP PLATE ASSY. 0017-00041-0616 RUBBER BUMPER (2 REQ’D.) A942-00016-0000 BRKT. & BEARING ASSY. 0017-00100-0025 1/4" E-RING 0942-00701-00XF SHAFT 0017-00103-0011 #10-32 LOCKING NUT 0508-001 12-OOXF BRACE — MAIN BRKT. 0017-00101-0755 #6-32 x 5/16 SLT. PAN HD. MS. (4 REQ’D.) 0852-00103-00XF SWITCH BRKT. (2 REQ’D.) A508-00022-0000 LEAF SWITCH ASSY. (2 REQ'D.) 0020-00202-0000 SWITCH PLATE (2 REQ'D.) 0017-00101-0527 #5-40 x 5/8 PHIL. RND. HD. MS. (4 REQ'D.) 0017-0002 1-0634 2 POSITION TERMINAL STRIP 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. SCREW

5-18

Page 57

NO. 942 — SATAN’S HOLLOW — COCKTAIL — CONTROL ASSY.

Page 58

SATAN’S HOLLOW — POWER CHASSIS ASSY. — 125VA., 115V. — ALL VERSIONS

5-20

Page 59

SATAN'S HOLLOW — POWER CHASSIS ASSY. — 125VA., 115V. — ALL VERSIONS -—- PARTS LIST

0945-00104-00XF A945-00029-0000 0945-00107-01XF 0017-00101-0123 MT00-00101-A000 0017-00103-0061 MT00-00099-A000 0017-00103-0084 6175-181T4-GXJK 0017-00009-0535 0017-00101-0565 0017-00103-0084 0017-00101-0067 0945-00103-O0XF 0945-00902-0000 0017-00021-0297 A945-00030-0100 A945-00030-0200 A945-00021-0000 0017-00101-0573 001 7-00103-0084 A945-00025-0000 0017-00021-0510 0017-00101-0140 0017-00003-0263 0017-00003-0005 0017-00003-0444 0945-00816-1902 0945-00816-1901 0017-00104-0107 0017-00103-0081 0017-00009-0422 0017-00101-0758 0017-00103-0061 0017-00101-0067 0945-00904-0000 0017-00003-0263 0017-00003-0217 0617-00003-0007 0945-00903-0000 A945-00022-0000 0017-00101-0067 0017-00101-0780 0017-00021-0629 A945-00019-0000 A945-00030-0500 0017-00101-C660 0017-00104-0107 0017-00103-0081 ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

CHASSIS. MTG. PLATE & BARRIER ASSY. STRAP (2 REQ’D.) #8 x 1/4 UNSLOT. HEX HD. SCR. (12 REQ’D.) ISOLATION TRANSFORMER W/O SHIELD ASSY. — 118V., 50/60 HZ. 48-32 HEX NUT W/SEMS (4 REQ’D.) POWER TRANSFORMER ASSY. — 115V., 60 HZ. #6-32 HEX NUT W/SEMS (4 REQ'D.) CAPACITOR — 3.5 MF., 440V. CLAMP #6-32 x 7/16 SLT. PAN HD. SCR. #6-32 HEX NUT W/SEMS #6 x 3/8 PHIL. PAN HD. SCR. (11 REQ’D.) PARTITION — LOCATED UNDER CHASSIS (NOT SEEN) SNAP BUSHING (3 REQ'D.) 2 POSITION CONNECTOR CONNECTOR & CABLE ASSY,. #1 CONNECTOR & CABLE ASSY. #2 CONVENIENCE OUTLET ASSY. #6-32 x 1/2 PHIL. RND. HD. SCR. (2 REQ’D.) #6-32 HEX NUT W/SEMS (2 REQ’D.) FILTER ASSEMBLY — 125V. — UNDER CHASSIS (NOT SEEN) TERMINAL STRIP #4-40 x 5/16 PHIL. PAN HD. SCR. (2 REQ’D.) SLO-BLO FUSE — 4A., 250V. FUSE — 2A., 250V. QUICK CONN. FUSEHOLDER (2 REQ’D.) — FOR ABOVE FUSES. CAPACITOR —~ 100,000 M.F. CAPACITOR — 55,000 M.F. #10 FLAT WASHER (4 REQ’D.) #10-32 HEX NUT W/SEMS (4 REQ’D.) CLAMP (2 REQ’D.) #8-32 x 3/4 PHIL. RND. HD. SCREW (2 REQ'’D.) #8-32 HEX NUT W/SEMS (2 REQ’D.) #6 x 3/8 PHIL. PAN HD. SCR. (6 REQ’D.) 5 POSITION FUSE HOLDER SLO-BLO FUSE — 4A., 250v. SLO-BLO FUSE — 2.5A., 250V. (2 REQ’D.) SLO-BLO FUSE — 3A., 250V. (2 REQ'D.) FUSE HOLDER BARRIER HEATSINK & DIODE ASSY. #6 x 3/8 PHIL. PAN HD. SCR. (2 REQ’D.) #6 x 1/2 PHIL. PAN HD. SCREW (2 REQ’D.) 5 POSITION TERMINAL STRIP — (UNDER CHASSIS) LINE CORD ASSY. — 115V. (NOT SHOWN) CONNECTOR & CABLE ASSY. #10-32 x 3/4 PAN HD. SCREW #10 FLAT WASHER #10-32 HEX NUT W/SEMS

5-21

Page 60

FRONT DOOR ASSEMBLY — U.S.A. 25¢

Page 61

FRONT DOOR ASSEMBLY — U.S.A. 25¢

ITEM

0090-00002-02BK 0017-00101-0121 A090-00073-02BK 0017-00101-0123 0017-00007-0019 0017-00101-0552 0090-0091 2-0000 A097-00005-0000 A097-00006-0000 0090-00128-00XF 0017-00005-0041 A090-00095-0000 0090-00126-03XF 0017-00101-0525 A090-00096-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0219 0017-00031 -0048 A090-00100-0000 0017-00103-0084 A090-00089-0000 0017-00101-0124 A090-001 12-0000 0010-00134-0000 0010-00181-0000 0017-00007-0083 0090-00129-O0XF 0090-00167-00XF 0093-00155-O0XF 0017-00100-0018 A090-00088-0000 A090-00105-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0132 A090-00059-0400 0017-00101-0147 A090-00077-0000 OMMNMMAWNA ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

DOUBLE ENTRY COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) DOUBLE ENTRY COIN DOOR W/DRESS PLATE #8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.) KEY HOOK #6-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) COIN ENTRY PLATE — 25¢ (2 REQ'D.) DOOR LOCK & KEY W/SCREW & NUT (OR) DOOR LOCK & KEY W/SCREW & NUT DOOR TILT SWITCH BRKT. DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ'D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #194 (2 REQ'’D.) WEDGE SOCKET W/BRKT. (2 REQ'D.) BRKT. ASSY. #6-32 HEX NUT W/SEMS (4 REQ'D.) COIN METER W/DIODE #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ'D.) COIN CHUTE & INSULATOR ASSY. (2 REQ'D.) SPRING SPRING 1/8 x 1-5/8 ROLL PIN PIVOT POST PIVOT LEVER REJECT LEVER E-RING REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ'D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ'’D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 PHIL. PAN. HD. M.S. (2 REQ’D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)

5-23

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

VI Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the cikcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet.

After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features.

6-1 NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the

coin acceptor itself. First, use a set of test coins (both

old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game Credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should ciose and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 64

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary

some from game to game, but no game’will work on

line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.

6-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 65

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, contro! and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several! chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary

on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,006 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to fow end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LS! circuits and three standard TTL MS! packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. |. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. . For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
Page 66

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit

Compare Test bit

Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

™,a| >Aa

cul tm a,

MREQ1——a
SYSTEM_/iona«22» a,

CONTROL S 55 21 34 a [Se a

waow |a

| 8 , a, AFsH 2] 2» a,

  • DDRESS
mr«82-80 CPU2» as

|? a,,

couwar—24 =!> Ay

CONTROL [> *

intr=—8 2![— An
nmi7 plan

—_a [—™ Ars

RESET =] y

-_ 25 CPU BUSRQ BUS ausak «—22_| CONTROL

"> v, bee d, 6 12 ° De. W 8 wv 7 DATA

enn—“ |je d,BUS

bg? Ds a Z-80 PIN CONFIGURATION 7 =o

Page 67

AoAis, (Address Bus) Tri-state output, active high. Aj-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. 1/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ag is the least significant address bit. During ° refresh time, the lower 7 bits contain a valid refresh address.

Dy-D; (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and !/O devices.

M, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 10RQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid I/O address for a !/O read or write operation. An {ORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output. active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) __ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device. RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to al! dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or !/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by 1/O devices. A request wili be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions) NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable_ interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00661. The program counter is automatically saved in the externa! stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent the current instruction from ending, and that a BUSRQ will override a NMi. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 68
  • Set Register |= 00H
  • Set Register R =00x
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state contro! bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

Page 69

MCR II SYSTEM P.C. BOARD JUMPER OPTIONS

VIDEO GENERATOR P.C. BOARD

  • = CUT JUMPER WIRES WHERE THIS SYMBOL “*" APPEARS. # = LEAVE JUMPER WIRES IN WHERE THIS SYMBOL “#” APPEARS.

The above table illustrates the fact that the Video Generator P.C, Board used in the MCR II System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires.

All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by thesame manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut. The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire’s number. If there is NO “*” under a jumper wire’s number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.

Page 70

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 71

VII. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off. ~ 2. Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

. Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 7-1 Removing and replacing coin acceptor

Page 72
  • Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) D Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water, O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 7-2 Cleaning the metal coin acceptor

  • To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-1. O Place the two pegs at the coin acceptor’s base into their retaining slots. OD Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

“E” RINGS

CRADLE

Figure 7-3 Lubricating the metal coin acceptor

Page 73

SQUEEZE PINS TOGETHER TO UNLOCK

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 7-4 Opening the plastic coin acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The piastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.

4, Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

7-3 O Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as: Paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door uniil it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 7-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters,
Page 74

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

MAGNET

>

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.

Page 75

PLEASE NOTE: ,

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

{F YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Page 76

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 77

Color T.V.

Color T.V Monitor

Introduction: (How to

use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the "DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also jiterature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 78

Symptom Diagnosis

1, Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. C1 Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. 0 Open width coil. O Open part in horizontal output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.

Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal syne off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) Silvery etfect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. Increasing brightness causes an increase insize and poor focus. A. Weak high voitage rectifier or regulation (high voltage unit).

8-2 10.

11.

12.

13.

14.

15,

16.

17.

18.

19.

20. Smail picture and/or poor focus: A. Low B+ voitage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync irom logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube {arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply cperating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board, B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No high voltage; check: For AC input to the “flyback”. Horizontat deflection stages. Flyback transformer. Yoke. Power supply. moom>

No horizontal and vertical hold; check: A. Syne transistors and circuit. B. Wires and jack from logic board to the monitor.

Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 79
  • Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
  • Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
  • Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontai output transistor. Cc. D. Defective high voltage disabling circuit. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence:

A.

m 0 OB Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. Picture tube defective. Metal foreign material is in picture tube shield. Nearby equipment is electromagnetically interfering. The poles of the earth are pulling off the purity. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SLY

INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

OL

FUSE (POLARITY DOESN’T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 80

COLLECTOR Ko COLLECTOR a BASE ————- BASE————— EMITTER TT eY EMITTER “TS

NPN TRANSISTOR PNP TRANSISTOR

' Ww —

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ :

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

rh wg = GROUND

8-4

Page 81

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS"” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the genera! order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hoid voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode Plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! Wher it breaks, first itimplodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole io ground. Use a piastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket} and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very aRon

8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 82

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. if you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 83

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its syne section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second.

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.

8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, ortear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator's frequency must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to makeit a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controis. There are only two, one for the red and one for the green.

Page 84

The blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's IC501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive:

Wells Gardner Electrohome 130VDC 120VDC

The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode.

After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can’t find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let’s say you have an Electrohome that isn’t working. No problem. You can scavenge parts from an old broken up one that you may have around.

Now let's say you have a Wells Gardner that isn’t working. STOP! This could bea problem. There are3 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a smail wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the

Page 85

screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT biasand is adjusted at the factory. When Wells Gardner sets it, they mark the Position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control tothe brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19” and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
  • You CANNOT swap any picture tubes between monitors!! In the past you could, but Wells Gardner is now using a new monitor. When ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G0O7-907 has a vertically mounted picture tube. if there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer’s part number between each one. If they match up, they are the same part.
Page 86

Supply Voltage and Symbols

Voltage | Operating Cireuit | vert. ose |

| | CAT cur Off

pene||_i
  • 130V |) Horiz. Osc. | Horz. D:
\|| Horz.Output
||Mert output

L 4.

|@|tv| Video Output

Q961 COLLECTOR

1VIDIV 200uSECIDIV 20VIDIV 10uSECIDIV

1P.31 DC COUPLED 4023 BOTTOM LINE =0 VDC

2vipiv 200MSECIDWW SWDJV 20uSECIDIV

LC. 301, PINS F

1VIDIV SMSECIDIV {VIDIV 20u SECIDIV

TP-82 TP.31, AC COUPLED

2OV/DIV SMSEGIDIV AWIDIV 200uSECIDIV

1.0. 301, PIN 13, NEGATIVE SIDE OF C303

2V/DIV SMSECIDIV "AR

O.SIDIV SMSECIDIV

O.5/DIV 20u SECIDIV

LLC. 301, PIN 15

1VDIV 2MSECIDIV SERVICE TE X-RAY RADIATION PRECAUTION:

PRODUCT CONTAINS CRITICAL | E TRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION | PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN TH ” COLOR MON!TOR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956

OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscliloscope with a poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC- TURER’S RECOMMENDED PARTS. _ AVERTISSEMENT: POUR MAINTENIR 4 LE OEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS
DONTLEFONCTIONNEMENT EST

CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

401 04 rer ork Bur oh P bux 28¢20601.8/L90K 25C20601.B/. 08K 2502068: 2SCIBISBVCCVE 2SCIBIGBVCKVE 25CISI4BVCVE

(G.ORIVE | (RCUTOFF] [6.CUTOFF]

nase o38e MF Sita see EY, omouT | 938i 250869

oreHOR. OR IV!380

odcnse3) one F 3508988 t 1 2SCECIOBK

R365 cog. 38K Zereey}

i AN VERTOUT cextes a), asceors_ > om oYNG AMP wose Haiia2s

paosmicut (HOR.CENTERING) s8e) mses ay. ular 7382 ‘30 ure 9S? [HORSize]

  • K4901D, K4906D, K4951D 5833 K4956B 8-10
Page 87

REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the origina! design, and components shown in shaded areas of schematic, or A * on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Ref. No.Part No.DescriptionRet. No.Part No.Description

RESISTORS RESISTORS (CONT.)

R201203X6500-645,1K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.
R202203X6500-52330 Ohm, 5%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon
R203,203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%, 1W Metal Oxide
R204203X6700327100 Ohm, 5%, 1/2W CarbonR372203X9101-11942K Ohm, 5%, 1W Metal Oxide
205203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon
206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide
R207340X2201-934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
R208203x6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88640K Ohm, 5%, 1/4W Carbon
R209340X2201-934200 Ohm, 5%, 1/4W Carbon379203X6500-88640K Ohm, 5%, 1/4W Carbon
R210203X6500-540390 Ohm, 5%, 1/4W GarbonR380203X6500-865,8.2K Ohm, 5%, 1/4W Carbon
R211340X2201.934200 Ohm, 5%, 1/4W Carbon381203X6500-7242.2K Ohm, 5%. 1W Metal Oxide
R214203X6500-645,1K Ohm, 5%, 1/4W CarbonR383203x9014-387150 Ohm, 5%, 1W Metal Oxide
R215203X6501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 5%, 1/4W Carbon
R216203X6500-6451K Ohm, 5%, 1/4W Carbon503204X1700-535150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203X9014-26747 Ohm, 5%, 1W Metal Oxide
R218203X6500-645,1K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1/4W Carbon
R219203X6501-126400K Ohm, 5%, 1/4W CarbonR506203x9104-10515 Ohm, 5%, 2W Metal Oxide
R220203X6500-645,1K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp.
R221203X6500-405100 Ohm, 5%, 1/4W Carbon%R60t204Xx1625-0583.3 Ohm, 5%, 10W WW
R222203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide
A224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
R225203X6500-16910 Ohm, 5%, 1/4W CarbonR201204x2070-0722K Ohm-B Semi-Fixed
R226203X6500-16910 Ohm, 5%, 1/4W CarbonVR301204X2070-0845K Ohm-B Semi-Fixed
R227203X6501-04447K Ohm, 5%, 1/4W CarbonR303204x2070-055
R228203X6500-6451K Ohm, 5%, 1/4W CarbonR351204x2070-072
R229203X6700-421270 Ohm, 5%, 1/2W CarbonR352204x2070-0722K Ohm-B Semi-Fixed
R230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R232203X6500-86382K Ohm, 5%, 12W Comp.
R233203X6500-468180 Ohm, 5%, 1/4W Carbon
R234340X2820-93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Ohm, 5%, 1/4W CarbonC201203X0014-0881000 uF, 16V, Electrolytic
R236340X2820-93482 Ohm, 5%, 1/4W Carbon202202X7200-064330 pF, 500V) Ceramic
R301203X6500-508270 Ohm,5%, 1/4W Carbon203202X7200-043220 pF, 500V) Ceramic
R302203X6500-8638.2K Ohm, 5%, 1/4W CarbonC204202X7200-043.220 pF, 500V) Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W CarbonC205203X0014-076470 uF, 16V, Electrolytic
R304203X6500-7242.2K Ohm, 5%, 1/4W Carbon208203X1810-1490.1 uF, 125V Mylar
R305203X6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-109022 uF, 100V Mylar
R306203X6003-2017.5K Ohm, 2%, 1/4W CarbonC301203X0014-065330 uF, 50V Electrolytic
R307203X6500-8255.6K Ohm, 5%, 1/4W CarbonC302203x 1600-563.0.033 uF, 50V Mylar
R309203X6500-96522K Ohm, 5%, 1/4W Carbon303203X0629-0373.3 uF, 50V Electrolytic
R310203X6500-98839K Ohm, 5%, 1/4W CarbonC304203x 1600-3660.068 pF, 50V Mylar
R311203X6500-7623.3K Ohm, 5%, 1/4W CarbonC306203x0412.01222 uF, 16V Tantal
R312203x9014-7414.7K Ohm, 5%, 1/4W Carbon307203X 1600-6340.033 UF, SOV Mylar
R313204X1450-5371k Ohm, 5%, SW CarbonC308203X0025-1743.3 uF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W CarbonC309203x1207.1000.068 uF, 100V PP
R315,203X6500-16910 Ohm, 5%, 1/4W Carbon310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 1/4W Carbon311203X0041-02510 uF, 160V Electrolytic
R317203X6700-10712 Ohm, 5%, 1/2W Carbon6312202X7050-2484000 pF, 500V Ceramic
F318203X6500-540390 Ohm, 5%, 1/4W Carbon6313203x0040-05247 uF, 160V Electrolytic
R319203X6500-645,1K Ohm, 5%, 1/4W Carbon314203X1201-2650.033 UF, 200V PP
320203x6501-00233K Ohm, 5%, 1/4W Carbon0315203x0629-023,1 UF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W Carbon351203X0629-0231 uF, 50V Electrolytic
R322203X6500-88640K Ohm, 5%, 1/4W Carbon352203X0619-04547 uF, 25V Electrolytic
R351203X6500-88610K Ohm, 5%, 1/4W CarbonC353203X1190-0150.0082 pF, 50V Mylar-PP
R352203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 uF, 25V Electrolytic
R353203X6501-08668K Ohm, 5%, 1/4W CarbonC355203X1600-3660.0068 pF, 50V Mylar
R354203X6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-4830.01 uF, 500V Ceramic
R355203X9205-1436.8K Ohm, 5%, 3W Metal Oxide359202X8065-608100 pF, '500V Ceramic
R358203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
R360203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W Carbon362202X7203-0320.01 uF, 50V Ceramic
R362203X9014-6451.8K Ohm, 5%, 1W Metal OxideD40363203X1270-9118700 pF, 1.5 KV PP
R363204X 1527-7513.9K Ohm, 5%, 7W Metal OxideC365203X1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203x0019-02622 uF, 25V Electrolytic
R365,203X6501-00233K Ohm, 5%, 1/4W CarbonC367202X8065-1626 pF, 500V Ceramic
R367203X6500-88640K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 UF, 50V Ceramic
R368,203X5602-185,330K Ohm, 5%, 1/2W Comp372203X1207-1250.1 uF. 100V PP

8-11 MAIN BOARD (CONT.,)

Rel. No.Part No.DescriptionRef. No.Part No.Description

CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)

ceo202X7200-087470 uF, S00V Ceramic2206200X3181-523Transistor (NPN) 28C1818GR
A C501203X1810-1490.1 uF, 125V Mylar207200X3181-523Transistor (NPN) 28C1815GR
4. C502202X7050-2821800 pF, 500V Ceramic208200X3181-523Transistor (NPN) 28C1815GR
4 6503202X7810-2142200 pF, 125V Ceramic209200X3181-523Transistor (NPN) 28C1851GR
A.c504202K7810-2142200 pF, 125V Ceramic210200X3181-523Transistor (NPN) 28C1851GR
0505208x0220.075560 uF. 200V ElectrolyticQ301200X3181-523Transistor (NPN) 28C1851GR
C508203X0040.03422 uF, 160V Electrolytic302200X3207-306Transistor (NPN) 28C2073LBGL2
807203X0041.05747 uF, 160V Electrolytic303200X3207-306Transistor (NPN) 28C2073LBGL2
701203x0010-01000 UF, 25V Electrolytic351200X3248.217Transistor (NPN) 28C2482BK
702203X0634-06110 uF, 100V Electrolytic362200X4589-802Transistor (NPN) 2508988
703202X7050-2481000 pF, 500V Ceramicaw et200X2300.033IG HA11423,
1501200X2600-183IC STR3B1

SEMICONDUCTORS

0203201X2010-159Diode, 182076-27
0204201X2010-159Diode, 1$2076-27TRANSFORMERS & COILS
0205201X2010-159Diode, i$2076-27L3612O1XA710-134Coll, (RF Choke)
D206201X2010-159Diode, 1$2076-27L352201X5000-083Coll, Horiz. Size
0207201X2010-159Diode, 1$2076-27Lt611X0004-007Coll, Adg.
D208201%2010-189Diode, 182076271351202X1300-080Transformer, Hor. Drive
209201X2010-159Diode, 1$2076-274k 1352200x9720-301HvUnlt M41
0301201X2010-165Diode, 1s$81
0302201X2010-169Diode, 1$2076.27MISCELLANEOUS
303201X2010-159Diode, 182076-27F501204X7120.073Fuse, 4 Amp. 125V
D304201X2120-009Diode, RH-IV402206X5008-632Recep W Wire 3P-M-BG
305201X2120.009Diode, RH-IVP201204X9600-466Plug, PWB 3P-J
0306201X2010-159Diode, 1$2076-27P202204X9601-477Plug, PWB 6P-Q
A0s01201X3120.216Diode, RM-1AVP4o1204X9600-298Plug, PWB 4P-B
0502201X3120.216Diode, RM-1AV501204X9600.249Plug, PWB 2P-B
4.0503201X3120.216Diode, RM-1AV601204X9600-304Plug, PWB 4P.C
0504201X3120-216Diode, RM-1AVTH5O1201X0100-112Thermistor
D505201X3120.216Diode, RM-1AV
D508201X3120.216Diode, RM-1AV
0701201X2120.234Diode, RU-2VFINAL ASSEMBLY PARTS
0702201X2120-009Diode, RH-1VA 88X0138-50819VLTP2z Pix Tube
201200%3181-523Transistor (NPN) 2SC1815GR205X9800-158Lateral/Purity Assembly
Q202200X3181-523Transistor (NPN) 2SC1815GRAe 202X1111-201Yoke Deflection
203200X4056-260Transistor (PNP) 2SA562-Y-TM204X9301-255CRT Socket
204200X4056-260Transistor (PNP) 2SA562-Y-TM291X5004.262Automatic Degaussing Coil Unit
205200X4056-260Transistor (PNP) 2SA562-Y-TM

NECK BOARD RESISTORS CAPACITORS

R401203X6000-729220 Ohm, §% 1/4W CarbonC401202X7050-2691200 pF, 500V Ceramic
R402203X6500-540390 Ohm, 5% 1/4W CarbonC402202X7050-2481000 pF, 500V Ceramic
R403203X6000-661820 Ohm, 5% 1/4W Carbon6403202X7050-2481000 pF, 500V Ceramic
R404203X6000.729220 Ohm, 5% 1/4W CarbonCaos202X7050-2821500 pF, 1.5KV Ceramic
R405203X6500-540390 Ohm, 5% 1/4W Carbon405202X7050-4830.01 uF, 500V Ceramic
R406203X6000-661820 Ohm, 5% 1/4W Carbon
R407203X6000-729470 Ohm, 5% 1/4W Carbon
R408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS.
R409203X6000-661820 Ohm, 5% 1/4W Carbon
Ra10203x9104.82418K Ohm, 5% 2W M.O. Formingapevecteent4Tandtstor (NEM 2sceneeLe
Ratt203X9104-82418K Ohm, 5% 2W M.O. Formingo403200%3206-800Transistor (NPN) 25C2068LB
Rat2203X9104-82418K Ohm, 5% 2W M.O. Forming
Ra13203X6000-9982.7K Ohm, 5% 1/2W Comp.
Rat203X6000-9982.7K Ohm, 5% 1/2W Comp.
Rats203X6000-9982.7K Ohm, 5% 1/2W Comp.MISCELLANEOUS
Rate203X9105-1542.2 Ohm, 5% 2W Metal OxidecardporticredinedRECEP W.Wire4P-&
Ra19203X6500-7412.7K Ohm, 5% 1/4W CarbonLied204X9600-254Plug, PWB 3P-A
R420203X6500-7412.7K Ohm, 5% 1/4W CarbonP43goaonn eetPlug, Pin 1P.0
.P701204X9601-020Plug,PWB 4P-£
Ra21203X6500-7412.7K Ohm, 5% 1/4W Carbon9.
vRao1204X2115.014500 Ohm, -B Semi-Fixed
vrao2204X2115.014500 Ohm, -B Semi
R403204X2115-0065K Ohm, -B Semi

R404 204X2115-006 R405 204X2115-006

8-12

Page 88

X90} POWER DRIVE 2S¢2686 X 902 ERROR AMP 2SC1890

Hevea, ascia Bowen REBAR ome ascasee AMR 25A67 3°

X303 SEAM LIMITER 2SA673 )x301,x302,x808,x806 Isync AMF [2SC4S4C or eecieas

BE [3804 BLANKING 2504540 or 25e Ices Kiol=x103 RG. VIDEO OUTPUT 28ca6il or Z8ciS14V

xso1 abies

Tt iE pe [st a aa

X70! X-RAY PROTECTOR 28C4546 or 25cise

ACIZ0V 6OH:/SOHz 10% Yor BEFLEcTiON voxe

501 HORIVE. 28c1s07 BO, asces7iv 25ca6hi or eéc2sionK

  • HOUT ad 28pe98 or L 280869 250820 0 Veen wearen

00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (Q) (K->KQ, M-~MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1—> (yF) working voltage -> 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP -* non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. © indicates test point connection oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety syrnbol with identical type.

NOTE: FR ~ fusible resistor —33—

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)

Page 89

REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.Ceramic Capacitor
Comp. R: Composition ResistorM CapMylar Capacitor
OMR: Oxide Metal Film ResistorE Cap.Electrolytic Capacitor
VR: Variable ResistorBP E Cap.Bi-Polar (or Non-Polar)
MFR: Metal Film ResistorElectrolytic Capacitor
CMF R: Coating Metal Film ResistorMM Cap.Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.: Metalized PP Capacitor

PS Cap : Polystyrol Capacitor . Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and mode! number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, al! parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Part Number Main P.C.B. Ass'y SU-1133A CRT Socket P.C.B. Ass'y SU-3032A Purity Shield Ass'y 07-220083-03 Outside oi ihe P.C.B. Ass'y Symbol Description Picture Tube 19°

aAsDefA Yoke

PC Magnet Ay A\Fiyback Transf. A AHVR

ROSUNFstor 2202,25W K

co4 C Capacitor 150pF, AC1.5KV X01 Si. Transistor x02 Si. Transistor sc Screw #8-3, sc Screw %s x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) C911 Capacitor 100nF 10% 400V F921 Resistor, Wirewound 3392, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symboi Description

3105vR 200
R3106Vv200
R3113VvR 5K
R3114VvR 5K
R3115,VvR 5K
R3116OMR 10KQ2W J
R3117OMR 10KQ2W J
R3118OMR 10K Q2W J

R3119 Comp. R 3.3K2%W K R3120 Comp. R 3.3K2‘%W K C3121 Comp. R 3.3KQ2%WK

Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF DC1400V P

Coils Symbol Description L3101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 28D870 28C1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-93 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part-Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEW53EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 90

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol aA Description Si. Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR 1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903, R1904 R1905, AQ 1908 AR 1909 R1910 ASFR1901

Capacitors Symbol 1301 1402 C1407 C1411 C1412 C1508 4Ac1512 AC1513 AC1514 C1515 C1520 C1523 C1524 Ac1531 4C1532 1904 C1905 Descripti v Vv CMF OM OM OM Vv AF AXCMF v Om OM om CMF CMF OM OM ZN ZN A\CMF A\CMF A’Posistor UNF CMF OM OM AXCMF Vv ACMF AF DDVDVDVVVDD DVVDVVVVVDVVDVDVDVDDVDIVDID ion R 2002 2002 68Q1W J 3.3K Q1W J 2.7K QAW J 12KQ2W J 10KQ 6822W K 11.BKQ “UW +1% 5KQ. 10KQ2W J 8.2KQ2W J 82022W J 8.2Q1W J 4.701W J 6822W J 39021W J

392.%2W +1% 7.68KQ YW +1%

2Q7W K 4.703W J 10KQ2W J 18K QW J 47 QW +1% 2KQ 2.74K Q’YW +1% 2202'%W K

Description BPE Tan. E E E PP A\pP APP A\pP PP BPE E M APP APP Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap Cap. 3.3uF 50V A 2.2uF 16V K 4.7uF 6.3V A 100uF 160V A 3.3uF 160V A S600uF SOV J 2000pF DC1500V J 2000pF DC1500V J 2000pF DC1500V J 0.53uF DC1200V J 3.3uF 50V A 1uF 160V A 0.1uUF 200V K 2000pF DC1500V J 1500pF DC1500V J

. 10UF 250V A Part Number 28C1514VC 28C1514VC 2SC1514VC.

Part Number A76068

Part Number QVZ3230-002 QVZ3230-007. QRX019J-6R8 QRG019J-532 QRG019J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRG019J-391 ERZ-C05ZK471 ERZ-COSDK271 QRV122F-3902 QRV142F-7681 AT5414 QRFO76K-2RO QRX039J-4R7 QRGO026J-103Z QRGO019J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES1CK-225B QEWS1JA-475 QEWS52CA-107 QEWS52CA-335 QFP31HJ-552 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z, QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW5S2EA-106

Page 91

Coils

Symbol Description Part Number

L1502Linarity CoilA39835,
11503Width CoilC30380-A
L1504Heater ChokeC30445-A

Transformers

T1501Hor. Drive Transf,A46022-BM
71503Side Pin Transf.C39050-A

Semiconductors

101501IcHA11244
X1101Si. Transistor2SC1685(R)
X1102Si. Transistor2SA673(C)
X1103Si. Transistor2SC1685(R)
X1104Si. Transistor2SA673(C)
X1105Si. Transistor2SC1685(R)
X1106Si. Transistor2SA673(C)
X1301Si. Transistor28C1685(R)
X1302Si. Transistor2SC1685(R)
X1303Si. Transistor2SA673(C)
X1304Si. Transistor2SC1685(R)
X1305Si. Transistor2SC1685(R)
X1401Si. Transistor28D478
1402Si. Transistor2SD478
X1501Si. Transistor2SC2610BK
X1901Si. Transistor2SC2688 (K.L.M.)
X1902Si. Transistor2SC1890A (E.F.)
01101Si. DiodeWO6A,
01102Si. DiodeWO6A,
D1103Si. DiodeWO6A,
D1301Si. Diode18Z473H
D1401Si. Diode18Z473H
D1402Zener DiodeRD10F(C)
D1503Si. DiodeHF-1
D1504Si. DiodeVO9E
D1505Zener DiodeRD11E(B)
D1506Si. DiodeWO6A
D1507Si. Diode18S81
D1508Si. Diode18Z473H
Ap1701AZener DiodeRD20EV2
A\D1901ASi. Diode181887A
4\D1902AXSSi. Diode181887A
A\D1903ASi. Diode181887A
4\D1904ASi. Diode181887A
AXD1905Zener DiodeRD6.8EV3

Miscellaneous

AF1901AfFuse 1.254QMF53U1-1R25S.
AXF1902AXUL Fuse 3AQMF66U1-3ROS
Page 92

AEEN UE XIOL_XIOS ond KIS VIDEO AMR ZSC489C oy 28¢1688, Xi92_x104 ard XIG6 VIDEO AMP 250673

301,202, X305,X306 SYNC AMP) 2SCASAC or 2SCi685

304 BLANKING | ascasac ‘crt SocKET pcp assy J) |

sreses SU-1103A | MAIN PCB ASSY f ——— |

X70) X-nAY PROTECTOR SOLBPIE oscosriv 380686 or L In 2 sd 28¢2611 or 28Ca00aK 250869 {u Ck “6 ee ACI20V 60H2/50HE 210%

G07-FBO

00-4147-03 Schematic Notes Unless otherwise specified Resistance: (2) (K*KQ., M*MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-» (yF) working voltage -> 50 (V) ceramic capacitor Inductance: ( H) Electrolytic Cap: Capacitance Value (yF)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection aby indicates chassis ground unless otherwise specified Hz __ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.

NOTE: FR - fusible resistor 2x3

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 93

REPLACEMENT PARTS LIST - ELECTROHOME 13”’ MONITOR

Components identified by the 4\ symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade tive safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.
Comp. R: Composition ResistorM Cap
OMR: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MFR : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and mode! number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

Symbol

Cutside of the P.C.B. Ass'y Symbol Avo1 AsDY01

ARII AROS Aco4 x01 Ico1 Lot

BR BR sc WA

CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y

Description APicture Tube A\Deflection Yoke

AFocus VR UNF Resistor 2202, 25W. K ASC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base

8-19 Part Number

SU-1103A SU-3016A

Part Number 370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Lt. Main P.C.B. Ass’y (SU-1103A) Parts List

Resistors Symbel R1406 P1408 A1410 R414 R1415 R1421 R1422 ASFR1401 A\R1503 R1504 R1509 R1511 R1514 1515 R1522 R1523 R1528 R1534 VR1501 A\R1703 ASR1704 AxR1901 R1902 R1903 R1904 ASFR1901 Capacitors Symbol 1402 c1411 C1412 1508 C1511 Ac1512 AXC1513 AC1514 C1515 C1520 C1524 C1904 C1905 A\C1907

Coils Symbol L1501 11502 L1503 1504 11901

Transformers Symbol 71501 T1503 Description VR 2002 VR 2002 CMF R 6.821W J OM R 33KQ1WJ OM R 27KQ1WJ OM R 12KQ2W J R 10KQ R 6822W K ASCMF R= 11.8KQYAW +1% VR SKQ OM R 10KQ2W J OM R 5.6K22W J OM R 68022W J CMF R 8.291W J CMFR 4.7Q1WJ OM R S622WU OM R 39021WJ

ZN R AXCMF R 39K QW +1% ASCMF R 7.68KQ%W +1% AsPosistor UNF R 2Q7WK CMF R 5.623W J OM R 10K22W J AF = R 2202%WK

Description Tan.Cap. 2.2uF 16V K E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600pF 50V J E Cap. 47uF 160V A A\PP Cap. 2000pF DC1500V J App Cap. 2000pF DC1500V J AXPP Cap. 2500pF DC1500V J PP Cap. 0.53uF DC1200V K BPE Cap. 1uF 50VA M_ Cap. 0.1uF 200V K E Cap. E Cap. 10uF 250V A A\MM Cap. 0.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRG019J-332 QRG019J-272 QRG029J-123 OVZ3224-014H @QRHO24K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORG919J-391 ERZ-CO5ZK471 ERZ-COSDK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEWS2CA-107 QEW52CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEW52EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A, A39475-J

Part Number A46022-BM 39050-A

Page 94

Semiconductors Symbol 101501

x1101 X1102 X1103 X1104 X1105 X1106 x1301 X1302 X1303 X1304 X1305 x1401 x1402 x1501 x1701 01101 01102 01103, 01301 01401 01402 01503 01504 01505 01506 01507 01508 401701 401901 4401902 A\01903 4401904

Miscellaneous Symbol AMF1901 ASF1902 Description Le,

Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor |. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si . Diode . Diode Zener Diode Si Si Si . Diode |. Diode . Diode AdZener Diode ASi ASi ASi . Diode . Diode . Diode ASi. Diode

Description AsFuse 1A AXUL Fuse 3A

8-21 Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SD478 280478 2SC2610BK 2SC1685(P-S) WO6A. WO6A WO6A 182473H 182473H RD10F(C) HF-1 VOgE RD11E(B) WO6A. 1S8S81 182473H RD20EV2 1$1887A 1$1887A 181887A 181887A

Part Number QMF53U1-1R0S QMF66U1-3R0S

Page 95

CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Resistors Symbol R3105 R3106 A3113 R3114 A3115 R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol C3107 C3108

Colls Symbol 13101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol rN Description 2002 2002._ §KQ 5KQ 5KQ

IM 1OKQ2W J

OM R 10KQ2W J Comp. R 3.3K2%W K Comp. R 3.3KQ%W K Comp. R 3.3K2%W K OOo<<<<< DDDDDVID

Description E Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description A\CRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO29J-103 QRGO29J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEW52EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2SC2611 28C2611 28C2611

Part Number AT5522

Page 96

IX Schematics and Wiring Diagrams

Page 97

9-1 ie

SOUND JO BD. as ae

Page 98

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 99

DESIGNATION LIST

DESIGNATION DESCRIPTION

ci,c2 47? mf 25v rd.tent C3,C4 22mf Gv |! | C5,Cé 470mf 6v ax.elect. C7-C10 Amf 50v ax.cr CPT 220mf 25v ax elect. CP2,CP3 Amf SOv ax.r

RIR2 2.7KN V4w 5% CRBN,

R3,R4270m""

R5-R8 TO W2w "

U1,u2 MB3730

Jt BPin STRT KKIS6

J230""

26 n "

HSA1,2 HEATSINK ASSY.

MH1-MH4 HEYCO BUSHING Lea [sin] 5 \ ve / CE cp

Cl Omen a1@) C4 fics] cin

4hrs cant na HSAL HSA2

(coe|re

DIM. TOLERANCES fon «TRON UNLESS OTHERWISE SPEC JP MH4 +

CONCENTRICITY T1.R 002TUK] 9-

FRACTIONAL + 184 Sey wae

DECIMAL.°

HOLE DIA + 0 ANGLE 212° FELEC crn FANISH 00 NOT SCALE DWG

CROSS REFERENCE LIST

DESCRIPTION QTY DESIGNATION

mf 50vaxcr6C710,

CP2cP3 47 mf 25vrdtant 2 CiC2

22mf Ev "2C3,c4

220mf 25vaxSlec 1 cPi

470mf 6v2csce6
INV 2w 5%4RS-RB
270/4w2R3R4
27K °2.RLR2
MB37302ulu2

2PINSTRTKKI56 1 J2

Buh2Shue
4°""1Jl

HEATSINK ASSY 2 HSAI, HSA2

HEYCO BUSHING 4 MHI-MH4

PC BOARD ' PART NO

0986008001100

G986-008003100 0986-00800-1600 0986-00800-3200 0986-00800 -1700 0062-O026D3-1xXxx 0062 - 068B3-1xXx 0062 - 199 B3-1XXX 0066 -188X x - XX4x 3000 - 16367 - 0200 3000-16367 -0300 3000 -16367 -0400 A986 - 00010-£000

0017-00042-0014

A080 -90910-E 000

MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 ABALLYCO REVISIONS DUAL PWR. AMP. ASSY fraarsc A080-90910-E000 [MO05!1-00986- E0IO

Page 100

v AUoIG =

Jt ° WW

PIN 1N.C.son1
"2 Ll. auoleLAg 4 o

3 L. SHIELD z 3 7 7 4 KEY id 7 5 Vv AUDIC RETURN 5 x 7)

  • 6 R. AUDI a E °
7 7 A. SHIELD75 fo)
- 8 v AUDIG:Fy \

SHIELD a _ u 9) LU Q =

a: = <q a J|Woio e}= 6 Z)wjO oO a| Oo aw oo 2 | fe} Vv AUDIO zlo|/> O 515 = a « o w -

JenaS$12/0 Oo
PIN 1Re2.7K“= oO
7 2 R-A>E I

"3 KEY = N "4 Le @

  • 5 N.C. - fo) " 6 L- 7 q

SHIELD

RA

Nn !@ XN

Vv AUDIO =>iITI>10 CHIPS5s
+ cptcP2cP33s
220uttutstufPy Bases

25v 4 Br38

vaupie = >1z 7
9-4RETURN=8*

DIM TOLERANCES

UNLESS SPECIFIED

FRACTIONAL HOLE OFA

Page 101

DESIGNATION LIST_ DESIGNATION bescnerion DESIGNATION OESCRPTION. _pesiGNATION —_esuRIPTION

Rae atte, adeai08 rsa. eet

JENOTE: ALLBOARDS COME WITH Jt WIRE S. CHOKES avo CAPACITOR: BRE NEEDED FOR RADIATION

(CHOKES AND CAPACITORS BEGINS ae 3] Pht 2] pescriprion NCE_LIST.

Page 102

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 103

hl

DESIGNATION DESCRIPTION.

ci? 100 pf AX. ELECT cio 100 pf AX. CER

CPI-3, 5-10 CPI2-20,22-27, CP29-33, 35,36, CP38-41,43-47, Olt AX. CER. cP 49-54, 56-61, 63-67, 69-71.

CP4, 11,21,28,34, CP37,42,48,55, lOuf 25V AX, TANT cP 62,68

RIOI~119,201,202, 1K 1/4W 5%

RMI,2 BPIN IK SIP RMS IOPIN IK SIP

1c at EPROM Ic a2 74.8157 1c a3 74LSI57 Ic a4 74 LSS?

IC AS 74LSi57 ic a6 74LSI57 ica? 74LSI57

c Bl EPROM ic B2 TALSI94

1c 83 T4LSI94 ic B84 T4LS32 Ic 85 422 1c 86 422 1c BT TaLS32

ic cl EPROM

ic ce 74LSI94 Io cs TALSI94

Ico c4 74S 32 ics 422 1c C6 422 icc? TALS 32

1c Dt EPROM woo. 7T4LS194 1c D3 TALSI94 Ic D4 748273 1c OS T4LS157 Ic 06 74S 157 Ic 07 74.8273

Ic £2 7A LSI94 ic ES TA LSi94 ICE 4 TALS 374 CES T4USIST Ic E6 74.8157

ic Fr? 7400 1c F 3 74804 Ic ra TALS 374 Ic FS TALSIST 1c 6 74 US 157 OES! ESIGNATION

Ic Ic 1c Ic ic Ooa000 aenun—

1c rrxrzrzxr oe nun-

Ic Ic

Ic Ic aren

1c kK Ic K ic K ic kK Ic K ic K oenun —

Ic Ic

1c

Ic Ic

tc Ic ererere Noosun-—

1c Mt 1c M2 1c M3

Ic M4

Ic M5 ic M7

1c 1c 1c

Ic Ic 1c Ic zzzzz2zz Vousun—

ICS Ai,B1,C1,01

ICS B5,6,C5,6, J5.K5,L5,M5.

ICSK6,L6.

J3.4,5

Jwi-8

881.2 DESCRIPTION

74S 86 74.8 20 74.5283 74 LS 283 74.5283 74 LSI57

74.886 T4174

T4374

74175 T4174 T4USI57

74LS 30 7430

748273

TALSIST

74161

7430 7474

74161

2ia-2

T4LS20 7408 7474

74.8283

2114-2 TALS 157

7430 7432 74s 74 74161

74S 157

7430 7427 74.8273 74.8283 74S 245 7404 T4LSIS?

28PIN IC SOCKET

22PIN IS SOCKET

IGPIN IC SOCKET

24PIN SOCKET

JUMPER WIRE

BUSS BAR =F} — at

om cz +

[Cusfe]~~]
—‘4\uw
crycerere
we[es“2wy
lLiroJ2r
(eri)cDey2

7 1

TeasCos]Me]|;
Lft|J'
CPiéFis)Pia,

'

.5f]1
mcsrecs)Lee]a]iefe]:
ae:C2GaP20oDre4
==1
—[esr]'
veJ3 cg[]vei

oD 2

fest}coma)2
cr2*Cr 27cD2D

1801+). 8) 2 ww ;

o6osoe63o2°eies.8

ww ;

3a)coSSeaati
  • iws
:-as5
reFerarsFeae;

we :

oomics:;
eses”e4.ese2eo!1
-+1
pezGradGap[erazyKaz)Gadew'
c7:}
>;:;:2
o7oeaD«D3[eeTy

i? 1 ¢

GapEeary(eras)Gapem'
  • 3
Lf 8 cs£8csice:
|Bae3 ‘]ez
°F cs°? ics |31

:

ar)as[asaaas)az
GDGHrecraaGay

PROJ, ENG. ATISH GHOSH DESCRIPT! 100 Pf SOV AX. CER. Ol pt SOV AX. CER)

10 pt 25v Ax. TANT

100 wt 25V AX. ELECT

1K 1/4 CRBN, FLM ik 8 PIN SIP 1K 10 PIN SIP 24-2 7400 7404

74s04 7408 74LS20 7427 7430 74LS30 7432 TALS32

7474 7as74 74.586 T4LSIST

7416) 74174 74175 74LSI94 748245 7aLS273 74LS283 748374 93422

EPROM EPROM EPROM EPROM JUMPER WIRE BUSS BAR

.C. BOARD

24 PIN SOCKET 28 PIN SOCKET 22 PIN SOCKET

18 PIN SOCKET CROSS REFERENCE LIST

DESIGNATION C1Ol CP1-3, CPS-10, CPI2-20,CP22-27, CP29-33,CP 35,36, cP36-41,CP43-47, CP49-54,CP56-6!, CP63-67,CP69-7! CP4, 11, 21,28,34,37, CP42,48,55,62,68 4,2

RIOI- 119, 201, 202 RMI,2 RMS K6,LE Fe N6 Fs. L2 G2,L! N2 J3,K2, MINI s2 m2 84,7,04,7, K3U3 H3, M3 Gi Hi A2,3,4,5,6,7, 05,6, €5,6,F5,6,G6,H6, J6,L7,M7,NT7 KI, Ka,M4 H2,5

B2,3,C2,3,02,3,€2,3 NS 04,7, 04,N3 G3,4,5 L4,N4, e4.F 4 B5,6,C5,6, 45, K5,L5,M5 AL (VGA) Bi (VvGB) cl (vec) Di (vGoy wwi-8 BB1,2

53,445 ICSA1,B1,CI,01 ICS B5,6,C5,6, J5,K5,L5,M5, ICS K6,L6

vst@ On SATANS HOLLOW | "NONE Pa 6886-89800-1000 0986 - 00800 - 2500

0986 -00800- 2400

0986 -00800-1800

(0062 - 17983 - 1Kxx 0986 - 00804-1100 0986 - 00804-1000

0986 -00803 - 2300 0986 - 00803-2800 0986 -00803-8300 0986 -00803-3!00 0986 -00803-3200 0986 -00803- 3400 0986 -00803-3500 0986 -00803- 3600 0986 -00803- 4300 0986 -00803-4400 0986 -00803- 3700 0986 -00803 -4500 0986 -00803- 4100 0986 -00803- 4200 0986 -00803-2400

0986-00803- 2500 0986 -00803-2600 0986 -00803-2700 0986 -00803- 2900 0986-00803 -3000 0986 -00803-3800 0986-00803- 3900 0986 -00803-4000 0986 -00804-0800

ROM/¢ PROMPT IONS K 0628-00803-3026

0986- 00805-0200 0986 -00804-0900

A080 -91399-£000

0986 -00804- 4700

0986 -00804-0300 0986 -00804-0700

0986 - 00804-0600

MIDWAY MFG. CO.

ASS'Y DRAWING VIDEO GENERATOR P.C A084 -91399-A94 MO51-00941-A007 |

Page 104

ere | SCHEMATIC VEO GEN. os. Saere 'Most-00886-600s 3-age1 |

Page 105

DESIGNATION LIST

-DESIGNATIONDESCRIPTIONDESIGNATION.DESCRIPTIONom“DESCRIPTION.Q“DESIGNATION.PART NOS.

«6

c101-c103JOM 25y ax TANT33°F SOV 5% ax CERcia0986-00800-0900
cioe-ci27i yesol ae nerra0847 PF SOV AX-CER2cize,cize0986-00800-2800
ciee-ci29ATPF SOV AX CER7415273!OOPF SOV 5% AX.CERflciaz(9986 -00800- 1.000
oislOMF 25 ax TANTieee!330PF SOV ax CER2ciei.cies9986 00800-1300
ciseloMF 25V ax TANTPolvereenO47MF IOOV MYLARjic1390986-00800 .2800
130O47 MF IOOVMYL AK2LOIMF SOV AX CER47CP2-CP12,CPI4-CPI9,0986-00800-2000
;loovy.1o821-0029 cr29=cP 33,
siaCIM So ax. CER*2CPasCSPaS Epa ces
'1OOPF SOV ax CER"Giao,c!
cia3IMP SOVAX. CERraisesIMF SOV AX. CER,34¢104-¢127,c'43,C501-c5090986 -00800- 100
ciaeB3PF Sov Ax CER2-80 CPUIME 20v ax. TANT@Ci34,ci87,cls7-clsqce2-c6436-00800-'400
cias-ciseO022NF IOUU ION MYLARpevicrOME 25 aX. TANT.$Geeo,eaa apse e420. 2206, 0986-00800-0708
cis7-c183ME-aor NeryaoeSiar eos asnc7ACwE.CITC 72
c16i230° SOV ax CERfareise470 MF 6V AX ELECT4oPl,CPI2,CPa cee0986-00800-2700
cr62-c164MF 20V ax TANT741670
cee 0167foresee tin7483222 WM 1/8W 5% CARBONheaore 00383. xxx
“sJOMF 28V AX. TANTTaLs670te]Loo OHM1R2330062 -| 1083-1 xx¥
kdNOM 25 AX TANT7481382200Hm"34RiO8 “R31, R162,950!-P509906 2-13383-IXXX
M 73AOIMF SOV AX. CERTALSITS:300 OHM1R23!0062 16183. 1Xxx
esgi-ca0e«Mb S00 ALGER,330 0HM2RIGO R16:0062 14483 iXxx
‘«3ai53,822 7.24016082 - |7983- xxx
cP47OME 6 AX.ELECT7ex3RiS7,R158,81630082 B323-1Xx
cp2- m2OIMF 50V Ax CERTAO?27K7R30!-R306,R510eam i
os47OMF I6V AX. ELECTweseosaK1W283enzsnmeze,sez ames
cri4—crisOIMF SOV AX CERare9101-8107, 165.8166,8225,9225,2218sxx

easamess R402,

cr20JOMF 25v Ax. TANTmcisozs82 28,8232,8234,8285.840
Gpay cra?sOIMF SOV AX. CERThose?5.6K2RI73-R\78, RIS7-R202c082-21583- xax
CP29-CP33OIMF SOV AX. CERLSSe:RISS, R15002-27 7ARIAKA
Heesvox4146, 815%, RIS5,R156
C34JOMEPZ SV AXUTONT,OK6R209-RZN,627 KEZ?els BRE BK
en“SIME GOW Ax. CERFeraale2x279,8196“062—24583-1XxA
isATOM ISN AXELECT.741902K2R2i3,R2260062-24 783-1KXx
cre-crsOIMF SOV AX CER.a33K6wise,a20%-R 208Doe -25183-iK4x
cP52,cP53IOMF 25 AX TANTvapmsezeBota. wer3,R403-Ra04
cessATOM I6V AX ELECT.aie2.niaecose 27983. xxx
neox2.cose2751
cP202-ce208JOMF 25 AX. TANTTessared2fuseee - sere Ti
Rio\-Ri074.76 OM /AW 5% CARBONaieface.2eaecoe2- 32588-1084
RI 08-RI3!220 04M"74126IMES.i7
ai35aay7aus244
R138, RIA)ieox.741 si91
wae100KaY-3-89108200HM BPN SAR'ame0986-00805-0800
ISS, RI4BB20KT4LSi9l1.8KiOPIN S.1.PRMS0986 00805 0600
Riae‘OK7a742.7K\OPNSIF4awe evso9a6-n0ans-0500
R48100K"ase4.7KBPINSIP.1RM?0986-00805-0400
nse: B18O620K4.7KJOPINSIP2RM AMG(0986 -00805-0300

nisi me

Rise::“|
fismos‘naa5bie0986-0080!-0200

Risa IMES.

RIS5,RIS61K".|onado’:aoa‘998620802-0500
BlecmerhanDESCRIPTION.achedDESIGNATION.PART NOS._TIP 11039°91 G035986-00802-0400
aald+330 0HM
aiez2200Hmcsae-icsaio
eeallBaP SOCKET10986 09803 7400
neead:ale40PIN1G PIN .C SOCKET'soi0986 -00808-1400racso2,ope onggr 7400
RIGS,RIGEiid:OEdksaan:ESAS = IGSA0986-00804-1600745041re986-90803-6600
8179, R196Bn‘7107'ce0986-008n3-s900
sie24 PIN KKIOO RT ANGLE CONN741508\a33€03- 7300
3SPIN. KKIOO2PINKK 100 RT. ANGLE CONN'ue7427ics0986-00803- 7200
R197 R20256x /4w 5% CARBON3 PIN KKIOO:sen"'1Soe eseecoaee.raise‘B100998 .00803-6100
RameeaK""vaSPIN «x100";apn“83000-1 8386-0400nara'a9386.00803-6700
a27%I8PIN. KKIOO"J7PIN”ue3000-1 6366-0700748138487.88, 812,813(0986-00803 6500
’SKueTRIN KKIOO18PIN:us
a3000-1 6366-1800-

R226 ‘

8225,9226a2eIN KKIOOapm2vive0986-00804. 470074168:030986-00803 5300
cea:yacsire'aia0986-00803-7500
rails56986-u980%-9400

ni 3

oseo7405131$ae3386. 908¢3-s6c0
whetJUMPER WIRE.2iW We0986-00804-4000raus24aa567,B4,65,62 F2Oa86-c0803 4800
resiaadJUMPER WIREracseesA386-90803-6400
8234,8236aan7408273,as9986-00803-4700
R239LeosvELLOW LED7408367ca9986 -00803-7000
R301-R306ictalPaLs3raaS9986.30803-4690
R401eee.YELLOW LED,v£0%30286-00804-200074LS670233.8)3386-00803-6300
|ay-3-89102FoF?0386-00803-#500
R02,4.7Kae34
aacs-raoaLM 380039986-20803-4800,
Ra0s-R407aewc34on2c10,£00388-26803 - 5000
501-2509Zoo orna”ow\oPOSITION DIF8 POSITION OIF Swsws0986-00805-0900WCi4018337 089388 0080? 6200
R510oesw3a""1OPOS:TION DIP SW.17Swi(0986-00805-1000Mcaces229986-00803-7.00
sw4PUSH BUTTONS. WPB SWITCH‘swa0986-00805 -1 700PROMSB2-ADe0$86 00803-8220
RAWIKX8a60986-20803-8000

ROW/E>ROM 0 ar

xtatJO MHZ CRYSTALBONonsu/nom,
ouleee6 MMI CRYSTAL w/280EAC,ee
RM2-RM52.7K 10 PIN S.LP,WrSRO LEAD'AT AL0986-00805-1100,aanp eee.
Eswe pb owenMHoI01-MHQ103SNAPed:wosesone te
“noBec ons2-89 7880'a0986 0803-550

ws a

3Mia iol MHa.030017- 90007-9134
‘“ss_——= cemermcal MIDWAY MFG. CO.

Fu TE ae “T COMPONENT © AYOUT DRAWING ree 3105-0107 nares TRS [an WE

  • ed jl _] “SuPER SOUND T70 P-C-ERD Mo51- 00941 -A0'6
101-2103TiPHH0aarA084-90913- A941

eae fea OF 1/82

31042N4039-9
Page 106

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 107

DESIGNA

cro C102 C103 C104 Cros Cro6 cro7 ctos C108 cro cm C201 ceoz c2o3 Cao4 c2os e208 c207

ces

Rioy Rio2 Roa Rios Ri06 R107

Rio9 Rito Ann Rin2 Ring Ria ans TION + DESCRIPTION

4700u Ax Lect 470uf AX ELECT tut ax. cer TUL AX. CER 4701 AX. Cen 470uf AX. ELecT 100ul RO. TANT Aut RO. TANT 4.7ut AD TANT tut Ax. CER Sut Ax. CER Our MYLAR O33! MYLAR Out MYLAR O47ut MYLAR 20D! AX CER 7 Otut Ax. CER 0.082uI MYLAR

tut AX. CER

18ihm Sw WIRES, SPACER 6B80nm 1/2W 5% 100mm 5W WIRES. SPACER P7onm 1/4W 5% 2790nm 1/4W 5% 6.2K 1/4W 5%

Tk 1/4W 5% 1Gohm 1SW WIRES SPACER 6.Bonm 1/205% 68ohm 1/2W 5% 12K 14W 5% 4Tonm 1/4W 5% 1600nm 1/4W 5% DESIGNATION LIST

DESIGNATION «

Ria Rie R201 R202 R203 R204 R205 A206 R207 R208 R209 R210 R210 R212 R213

R214 R215 R216 Rear R218 R219

va 101,102

D101 D102 Di03 Dios D105 D106 D201 0292 92035

D205

2102 O105 0201

uw

v2 v3. ua

us

Lio1

Brot

Fo1A18

Fei

Tw

ws

ua

le

Lee

HSAt

Minar

wns

Famine DESCRIPTION

S600hm 1/4W 5% 1500Km 2W 2700nm 1/4W 5% 1.2K 1/4W 5%

aM 14W 5% 33M 1/eW 5% TOM 1/aw 5% 100K 1/4W 5%

33K 1/4W 5% 2M 1/46W 5% 1M 114W 5% 12M 1/4W 5% TSK 1/4W 5% 75K 1/4W 5% 220K 14W Sm

3.9K 1/4W 5% 12k 1/4W 5% B2ohm 1W 10%

270uhm Waw 5% NOK aw 5% 6B ohmi/ZW5%

1000hm POT

alse Ase ANF AtSE AIS 1N4001 1Na 183, INa148 1Na 148

1N4001 1N4001

2N2905 2N2905, 2Nagor

Umsus REG (M305 REG Lma900 AN28

22uH INUCTOR

BATTERY 3 6vOC GODEG C

2 8A S BLO Fuse

Fuse cL

FERRITE BCAD

Tie WRAP

SPIN PC MOUNT CONN(MALED ISPIN PG MOUNT CONN (FEMALE) 1SPIN PG MOUNT CONN (MALE) 3PIN © G MOUNT CONN (MALE)

FUSE TAG

SYSTEM TAG

HEAT SK ASS'Y 1

MOUNTING HARO WARE(HEAT SK) 2 SCREW 4 WASHER 2 HEXNUT

JUMPER WIRE

FERRITE BEAD MOUNTING HARE ak Ed yore

+ sO wese | 3 mie poise padi p

° 7 ve tear} 207, 0205 (R24) —

> fers) & ni] $F

Ra 4 * re t veo CJ} (EC) e203)

aor

| svsrew | ra

PROJ. ENG.:L. DEKKER [22S saTans HOLLOW Fuct [so o> TPER. MIDWAY MFG. CO.

A082-90412-D000 5/14/82 ‘ASSEMBLY DRAWING a5 va PwRSPY] | MO51-00945-B006 CROSS REFFERENCE LIST

DESCRIPTION oy 47pt aX. CER 820p1 AX. CER, Otu! AX. CER Otut MYLAR OS3u! MYLAR

O47ut MYLAR 9,082uf AX.CER tut aX. CER

tut RAD. TANT 47ul RAD. TANT 100ut WAD. TART 4700" AK. ELECT 47001 AX. ELECT

16ohm 15W 5% iBonm SW 5% ©.80nm 1/2 5% tOohm SW 5% 2Tonm 1/4W 5% 47onm 14W 5% Bohm 1/2 5% 3

820mm 1W 10% 1500hm 2W 5% 1G00Km 1/4W 5% 2roohm 174 4% S6Aohm 1/4W 5% 1k 1/4W 5%

12K 14W 5% 39k 1/4 5% 6.2K 1/4W 5% 39K 1/4 5%

75K 1/4W 5% 100K 1/4W 5% HOK 174w 5% 220K 14W 5% 1M 14w 5% yim 174i 5% 12M aw 5% 2M W/4W 5% 33M 1/4W 5% som 1/4W 5%

1000hm POT 2

L305 REG. 2 555 fl

L390 ' 4N28 1

A1SF RECTIFIER 5

1wa001 3 iNa14e 3

262905 2 2Neaor 1

BATTERY 36VOC 6ODEG-C FUSE 3/8A S-BLO ~ FUSE CLP TIE WRAP.

FERRITE BEAD FERRITE MOUNTING HOW

22u4 INDUCTOR 1 Fuse TAG 1

SYSTEM TAG 1 pce. '

HEAT SINK ASS'y 7 (SEE WS ASS'Y ORAWING "XX NOTE") 7 440% 10 SLT RNO 2 { 4-40. HEX NUT 2 WSH 4-120-.250-018 4

PIN F.C, MOUNT CONN. (MALE) 9PIN P.C, MOUNT CONN (MALE) 15PIN P.C, MOUNT CONN (FEMALE) 15PIN P.C, MOUNT CONN (MALE)

22AWG TOR BARE 2.5" 5 DESIGNATION *

e105,

205, 208,208 201,203,

c2o7 6103,104,1°¢,111

cpr

e108, 109)

C107 102,106 cio

a0

Riot Rut R104 R105, Ria 102,112,219 R216.

Rie

Riis 106,201,217 fanz R109 F113,202.215 Reva

R107,

R207 211.212

R208 R218 A218 R209

R203 R210 A208, R204 R205

vr 101,102

vie

us

ua

ua

101-195

106,204,205 0201-203

0102,108

Bio

Fy

FOrAB. wr

Fa12

FEMH,2

Lior

SAY

MH HSA 14,28, MHHSAIE, 26. MH HSA 1B.10 MH HSA 28,20

aa

awt5. PART «

0945-00811 0100 0945 09816 0400 0945-008 16-0 700 0945-005 16-0200, (094, 00816-0500 0945-u0816-0300 (0948-008! 6-190 0945-00811-0200

0a1.-90814-0300 9945-00811-0400 oy45-00811 9500 0945 -00816-0600 0945-0081 1-0700

0945-09815-0100 0945-00815-0200 (0962-04703- 1xxx 0945-00812-0100 (0062-068B3-1xxx 0062 08683-1Xxx

0082-09803: 1XXx 90062-104FS 1xXx. 0945-008 12-0200 (0062-12483: 1Xxx 0062-19883: 1x¥* 0062- 162B3- 1X

0062. 17983- 1xxx 0062: 18982- 1XX% (0062-20783- 1XXx (0062-21783-1XXX (0062-25 183- 1XXx 0062 26983 1xxx 0062-27983 1Xxx 0062-27783 1xxx 0062-29183 1Xxx (0062: 323B3- 1xxx 0062 32583 IXxx 0062- 32783- 1XXX 0062 33783. 1x4% 0062-34783: 1KXX (0062-37 183- 1X4x

0945 00874 0090,

0945-00513 -0100

(0229-00810- 4500 (0945-008 13-0200

(0945-908 13-0300

0945 -90804-0200

0945-00804-0500 (0945-00804-0500

0945 00808-0300 (0945-00804-0400

0017-00003-0377 10945-00808-0400 00*7-00003-0214

0945-00814-0300

0017-00009-0225

0017-00033 0159

(0945-00814-0200 M05 1-00945-A008 Mos 1-00945-A002 A080-90412-L0C0

4945-00008-0000

0017 -00101-vorar 0017-90103-0002 0017-00104 -007

9017-00021-0443 0G17-00021-0425 0017-00021-045" 0017-00021-04s0

0181-00087 -oave

9-11

Page 108

9-12 MT 89 MT 90 DOMESTIC EXPORT Fel FERRITE BEAD pol Riot O18 +127 4aMP “ se BRO ‘4945-00002-0000

FILTER ASS'Y

: 3 4-11 VIDEO DRIVERS 35-9 MISC

MIDWAY MFG. CO.

W/CKT SUPORT

'Rio_|
'10 .2Wor

' ———w—+ ni

Rio6.2K+
ss000Mrtoe102
o1ows70UF
:beSENSE ZV)
.“emio!
neied13 100
1iPPorJ6-4 Louie 8RD
''n10914-7 LOGIC 8RD
_iI15:1
'J-94_—SENSE44
\‘ennCOMMONto
H.TOTier 0.22uH ZIG 208 1N400Iay
''i\aeiswea veart
'ty:ware 7wwaoot | 370 s.evear, 7,208,
4fy)HS
ia4=SevJ5-1_COUNTER DRIVERS,

mx

:ua'awarme FERRITE BEADuo+5V/7.SAMP 16-3 .ooic BRO
|re°Ze,TTeR
;'0.16Losi
im'swLoic Ro
joane SLIfcite_AUK, BRD
SofMFlee

aioe

osMtLogealhe

Ma 1 (we ny A

meHteow |

an 1

twocoowr | 1‘2n2908
  • fe 1
wailzott'wna
ORY7\>Hn'7+ | cios
L\va+1 ciorvaio
wevne'3{uns0s+eour ("S100 T «7omr
teedimfPor
'rt'Vaanaus|
-\-4)'+veo|Looie aro
;ioecioRu |aie BRD
iian‘456044-10 Looe BRO
oiMecuntcare
q1IME
SENSETtJ|CONTROLS
aie D|5-7 CONTROLS
aes:COMMON,48-3 wise

i 4-2 -SENSE (SV) EARTH GND ~ — ORTIONALGND, _ __ _ JS-10_ COUNTER RTN

:I s,UNREG. AUX. V5-14 CONTR. LAMPS:
\1oweSo
VOLTAGE. @ FUSE VALUE VARIES \roSt UNREG FILTERED V__ 18-18 aypioexr.
me Sear\2104 pus 80 vew +1 ciot

wes D101-pI08

FROM. X-¥ MONITOR XFMRHi1owes AehiaCONTR-LAMPS
OR ISOLATION xPMR‘a. le aaah8216 AUDIO CKT.
we-2—aR208ry7
7;ovayaiow:
toesit~TWw
R2022H
us12ktS'= = = = -A6 synciRoNZariON
R201 4Nzee201 202 ROSrol |oo
270‘OLoIMe sige Tim 4/8920ta'

fe, 28

ro7i
~p20e202mioy oy
ieeeb.033mFmi,
54a| le‘
ry]aae eeseas ste

‘

*tythal
- = PUMP CHARGER -2Hos ow;

=F 1

, 4-18 RESET 208 R208 | e201 oom 100K! | 2n4aor . Pema) ‘PAQJECT ENG: L_ DEKKER eacaNrOLLOW.

1 Bh Teen a POWER SUPPLY I25VA

ONE SHOT A082-90412—D000 MOS |-00945-0007 L