Narc Service Manual (16-3036-101) Feb 1989
Narc (rev 7.00) (Williams, 1988) · Manual · 60 pages · 31 sections · original scan
16-3036-101 February, 1989
eee Joes!
Service Manual
WILLIAMS ELECTRONICS GAMES, INC. 3401 N. California Avenue Chicago, IL 60618
Prog rammed Chip Summary (Continued on Inside-Back Cover)
Image ROM Ctir A-5346-3036-5 Video RAM Seq. A-5346-3036-6
| Image ROM | ROM | 27512 | ard U: | k |
| Image ROM | ROM | 27512 | ROM Board U26 | 343-3036-16 | |
| Image ROM | 27512 | ROM Board U27 | 343-3036-17 |
=
o ig
| Image ROM | 27512 | RO! Board U31 | |||
| Image ROM | 27512 | ROM Board U32 | |||
| Image ROM | 27512 | ROM Board U33 | |||
| Image ROM | 27512 | ROM Board nd | A-5343-3036- aa | ||
| Image ROM | 27512 | ROM Board U39 a SAS eaOSEOT cds . | |||
| Image RO | 0 | 27512 | |||
| Image ROM | FROM | 27512 | ROM Board U44 | ||
| Image ROM | FROM | 27512 | ROM Board U45 | ||
| image | ROM | O | 27512 | OM Board U | 6 |
Image ROM ROM Board U50 | A-5343-3036-38
| I | ROM | ROM | ROM Board U51 | A. 5343-3036- 39 |
a sv 5 SE :
16-3036-101 February, 1989
SERVICE MANUAL
operation sbookkeeping eadjustment ediagnostics eunique parts
Programmed Chips on the Sound Board
27512 | Sound Board U3 Not Used 27512 | Sound Board U4 A-5343-3036-1 27512 | Sound Board U5 A-5343-3036-2
Be s Sound ROM | RM __| 27512 | Sound Board U38 | _A-5343-3036-6
NARC Sewice Manual 1- 3
Jumper Table
Ww3 wi W4 w2 W6 W5
NV
ge
nou sears
13/14 Ri
Sound Board ws : Wwé W16
W11 W214 :
Table of Contents
Chapter 1. Operating Procedures Programmed Chip Summary--Part 1........ . Programmed Chips on the SoUN BOard.......eecsssssssecssesessstescesstessersenuesseeessueesesiusessnuecceneeeeneesestee
Jumper Table............ Examine Your Game. Control Locations.
Power Turn-On... Game Operation Player Panel (IIlustration’
Game Adjustments, Bookkeeping, Diagnostics. Main Test Menu (lllUstration)........ecsssseeesseeee Typical Coin Bookkeeping Screen Page | (Illustration)...
Typical Coin Bookkeeping Screen Page 2 (Illustration)... Typical Audits Screen, Page 1 (Illustration)... Typical Audits Screen, Page 2 (Illustration)...
Typical Game Adjustment Screen (Illustration Typical Utility Menu Screen (lllustration).. Operator Message. ) 149
Game PHICING),.....ssesiseccccsssisecsocnsesessssenerittaceestduccrnsteneenstentenstsiasouindongeetthsbegesthieeentineqetatsseesbitnereesinnanss VRE
Standard Pricing Table... a Typical Custom eee Me Menu astaton Custom Pricing Table... peseeteenee
Installing a Dollar Bill Acceptor.
Chapter 2. Service Procedures. Introduction... Power-Up Tests..
RAM Power Pins (Illustration) Diagnostic Mode Tests Typical Main Test Menu (Illustration).........sssssssssssscsssceeesesseesesssssssnssssssnssssessensnsnsensssteseeesserccensssasesses 2-7
Typical Diagnostic Tests Menu (Illustration). Typical Sound Test Menu (ilustration).. Typical Monitor Patterns Menu (llustration}
Purity Screen with RAM Error (Illustration). Color Bars Screen (Illustration)... Troubleshooting Tables.
Chapter 3. Electrical Parts... Semiconductors. Unique Parts. 3-1
Hardware... Major Asse’ os Programmed Chip Summary--Part 2.
Warnings & Notices......sssssssssssssssscssssssssssssssssssussssssescsersessseseeeseesssssssuaseseeasesstsssssssnssessesseceesescssnssesesesseeee 3-8
Chapter 1. Operating
Procedures
Programmed Chip Summary--Part 1
Programmed Chips on the Sound Board Jumper Table Examine Your Game Control Locations Power Turn-On
Game Operation
Player Panel (Illustration) Typical Coin Bookkeeping Screen, Page 1 (illustration) Typical Coin Bookkeeping Screen, Page 1 (Illustration)
Game Adjustments, Bookkeeping, Diagnostics
Main Test Menu (Illustration) Typical Audits Screen, Page 1 (Illustration) Typical Audits Screen, Page 2 (Ilfustration) Typical Game Adjustments Screen (Illustration) Typical Utility Menu Screen (Illustration)
Game Pricing
Standard Pricing Table Typical Custom Pricing Menu (Illustration)
Custom Pricing Table Installing a Dollar Bill Acceptor
Examine Your Game
+ INSPECT THE OUTSIDE of the carton or game cabinet for shipping damage. « UNLOCK AND OPEN the bottom-rear door. Now check circuitry.
+ ARE CONNECTORS SECURELY ATTACHED? Reconnect any found loose. Don't force connectors! They're keyed and only fit one way.
+ ARE PLUG-IN CHIPS FIRMLY SEATED in their sockets?
«+ REMOVE THE BATTERY PAPER from the round, lithium cell on the CPU Board. This paper prevents the battery from powering the CMOS RAM until the game is installed. With the paper in, the game forgets your adjustments every time you switch it off.
+ UNWRAP THE POWER CORD coiled inside the cabinet. Don't plug it in yet!
« SCRUTINIZE MAJOR SUBASSEMBLIES, such as the monitor, player panel, transformer chassis and power supply. Make sure they're securely mounted.
- UNDO THE CONTROL-PANEL LATCHES. You can reach these from the coin door by extending your arm upward and to either side. Now check connectors and circuitry as above.
Control Locations
THE ON-OFF SWITCH is above the back (monitor) door. Standing before the game, you'll find the switch at the game's top-left corner.
POWER INTERLOCK SWITCH. Your game has two power-interlock switches. These are located at the back of the game, behind the top and middle panels. imagine that you're standing behind the game. An interlock is
in the upper-right corner of each panel. Each interlock is a spring-loaded DPDT switch. It turns off the game when you remove the panel. For servicing purposes, pull the switch out and the game will power up.
THE VOLUME CONTROL is inside the coin door and to your right.
THE ADVANCE SWITCH is mounted on a bracket behind the coin door. This switch is useful for many purposes: Accessing Diagnostic Mode Tests, reading the bookkeeping totais or making game adjustments. See relevant discussions later in this chapter.
THE MEMORY-PROTECT INTERLOCK SWITCH is behind the coin door. This switch must be open when you clear bookkeeping totals or make game adjustments. It automatically opens when the coin door is open.
THE CPU-BOARD RESET SWITCH is on the CPU Board near the +5VDC indicator LED.
Power Turn-On
WHEN THE GAME IS FIRST TURNED ON general illumination should light. A moment later, the game performs Power-Up Diagnostics...
- First, a scanning rug pattern appears. During this pattern, Videc, Scratchpad and Color RAM chips are tested. The test also demonstrates DMA operation.
- While the rug pattern is scanning, the game should sound two tones. These indicate the readiness of the Music and Sound Microprocessors on the Sound Board.
- A stationary, striped pattern replaces the scanning rug. This pattern is an artifact of the testing process.
- Briefly, an assembly diagram of the CPU Board appears. This diagram indicates test passage by the RAM chips and main microprocessor (GSP) U18. As they test good, the pictorial colors the chips green.
- A drawing of the ROM Board replaces the CPU Board diagram. As they test good, the pictorial colors the ROMs green. Untesied and not-used ROMs are shown in gray.
- In acorrectly running game, tests will be followed by the the High Score Table and a repeat of the two Sound Board tones. If failure messages come up on the screen instead, refer to Chapter 2.
DEMAGNETIZE THE GAME with a television degaussing coil. Besides the monitor, remember to degauss large steel parts (for exampie, the backdoor hinge). Do this whenever you move the game, and also as a regular, monthly procedure. Otherwise residual magnetism may cause color impurities that adversely affect your collections.
Game Operation
GAME START . INSERT COINS. The game allocates an adjustable number of credits per coin. This number appears on the CRT. For example, assume that your settings specify one credit for a quarter (U.S. factory pricing). A player deposits a quarter and presses 1-PLAYER START. On its screen, the game posts one credit. Then a one-player game begins.
Using player-2 controls for a one-player game is also possible: With one credit displayed, press 2-PLAYER START.
For a two-player game, at least two credits must be displayed. To initiate this two-player game, press both 1-PLAYER START and 2-PLAYER START.
PLAYER CONTROLS On its player panel, your NARC™ game has four pushbuttons and a joystick. Players can...
+ FIRE at evil pushers with the machine pistol.
+ PRESS ROCKET BOMB! Eliminate several pushers in one blast!
+ JUMP over broken sidewalks and other obstacles!
- CROUCH to duck bullets and garbage cans!
+ MOVE in eight directions with the joystick.
Player-1
Joystick
Player Panel
GAMEPLAY THE CITY'S OVERRUN! Slashers! Gangsters! Pimps! The punks are everywhere! The scum of the earth! And only the player can restore law and
order! Trigger finger spraying hot metal before him... ROCKET BOMB at the ready... The player is a macho urban guerilla, defending our city from the ultimate urban scourge! This is his neighborhood too. He's committed. He says NO to inner city decadence. He carries a badge and a moral code. And he backs them both with screaming lead.
FEARLESS, ALOOF... He blazes away with his machine pistol. Then he launches a devastating ROCKET BOMB to trap several baddies in simultaneous ambush! With JUMP and SQUAT buttons, he dodges bullets, dynamite and other missiles. But the lurking Loaf, death-dealing Dumpster Man, patronizing Pimp and horrible Hypoman are everywhere. And these mangy marauders stop at nothing. This is their turf. So they'll hurl more bombs and deal more corruption. Because they're forever preparing another rendevous with death. Here's a list of the nefarious gangmembers...
+ Loaf + Psychotic + Gangster * Slasher + Pimp * Dumpster Man + Hypoman «Mr. Big (Public Enemy Number 1)
THIS JOB DEMANDS GRITTY DETERMINATION, FAST THINKING! The city is a jungle. Pushers may lurk in manholes... They may dart by ina heavily armed, pink Cadillac... Or they might even buzz the player with their preemptive pushercopter! But the player laughs at danger. He scores bonus points by seizing contraband (evidence!) hidden in the Cadillac. And by busting these parasites on society. Then he blows that manhole. And he downs that pushercopter. Because no pimp is too high... And no gangster's too low to eat hot justice!
ENTER BUILDINGS. The player must seek out and investigate gang strongholds. When enemies dart out of a tenement, the player must enter. If psycho fiends slither in the subway, the player relentlessly pursues them. Not bullets, not bombs, not even mad dogs can deter him. For our hero's sworn duty is to case the hideouts and seize the evidence. Then he can bust another offender!
THE PLAYER STARTS WITH THREE LIVES. Busts and evidence win points. For every 100,000 points earned, the player receives another life. (The number of lives per game and points per extra life are operator adjustable.) The game displays a green bar to represent a player's current lifetime. When enemies wound the player, the lifetime and the bar shorten.
THE BIG TARGET. Ultimately the player pursues Public Enemy Number One, Mr. Big. Mr. Big is the shimmering, super slug king of the sleazy, slimy underworld empire. His glitzy, cosmopolitan crib is brimming with evidence. And he's the inevitable prospect for a megabust. But he's wily. He's quick. And he's amply equipped with the latest Hyper-Crimewave Technology. Nevertheless, the player must not permit him to escape! The dragnet must not fail!
Game Adjustments, Bookkeeping, Diagnostics
MENU CONCEPT. For your convenience, game adjustments, bookkeeping, audit totals and diagnostics are menu-driven features. Each menu is a list of several choices that you may act upon as desired.
LEVELS OF MENUS. Your game has several levels of menus. That is, one menu selection will send the game to another menu. The menus are arranged in outline fashion. That is, a menu of general options selects menus of more specific options.
NARC Sevice Manual 1- 13
NARC TEST MENU NARC: REVISION H.H
SELECT WITH UP/DOWN STICK ACTIUATE WITH ANY BUTTON
DIAGNOSTIC TESTS COIN BOOKKEEPING ws USTMENT
ERIT TO GAME OVER
Main Test Menu
PRESS ADVANCE. Adjustments, bookkeeping and diagnostics are available from the main test menu. Enter the main test menu by pressing the white ADVANCE button inside the coin door. ADVANCE is mounted on a bracket a few inches behind the door.
SELECTING AND ENTERING OPTIONS. To select an option you desire to investigate, move the joystick up or down. Watch the highlighted bar on the screen menu. This bar illuminates the selected option. You can enter the highlighted option by pressing any player panel button.
IF THE PLAYER PANEL EVER FAILS, ADVANCE can operate diagnostic and bookkeeping functions. First press ADVANCE as usual to initiate diagnostics or other modes. After that, each time you press ADVANCE, the game steps through menu options. ADVANCE isn't as convenient as using player panel controls. For example, it doesn't replace the joystick. However ADVANCE offers a good backup system for the player panel.
RETURN TO MAIN MENU. Normally you may exit the menu you're inspecting and return to the previous menu. In fact, "RETURN TO MAIN MENU" and "EXIT TO GAME OVER" are typical menu options. Suppose that you select
"RETURN TO MAIN MENU": The game returns to the option where it was before on the previous menu.
Pressing and holding ADVANCE causes the game to exit to Game-Over Mode.
DIAGNOSTIC TESTS As mentioned earlier, your game performs various tests at power-up. You can repeat any of these tests by entering DIAGNOSTIC TESTS from the main menu. Additional tests are also available. Chapter 2 covers these in detail.
COIN BOOKKEEPING Two COIN BOOKKEEPING screens are accessible from the main menu. The first screen details the number of coins through each chute. (The screen refers to a center chute, although some games don't have a center chute. See Installing a Dollar Bill Acceptor, later in this chapter.)
COIN BOOKKEEPING NARC REDISION #
LEFT SLOT COINS CENTER SLOT COINS RIGHT SLOT COINS PAID CREDITS
GAMES STARTED GAMES CONTINUED TOTAL PLAYS PLAYS UNTIL H.S, RESET
Typical Coin Bookkeeping Screen, Page 1
TOTALS AND COLLECTIONS DON'T MATCH? Coins actually collected may not equal the top subtotal on the TOTAL COLLECTION page. A common reason is this: Employees often play by opening the coin door and tweaking coin microswitches for credit. That is, records of collections with the coin door open don't reflect game sales. The page 2 feature COLLECTED WITH COIN DOOR CLOSED addresses this issue. This feature presents a second set of coin totals. The new totals permit you to separate "sold games" from "tweaked games." Furthermore, the feature is a means of monitoring employee gameplay.
Both screens are also accessible from the coin vault switch. The vault switch permits collection agents to keep track of (but not clear) coin totals. Subtotals may be cleared from the vault switch.
TAL COLLECTION
LEFT SLOT COINS 432 CENTER SLOT COINS 0 RIGHT SLOT COINS 398 TOTAL COLLECTION $207.50 SUBTOTAL $207.50
COLLECTED WITH COIN DOOR CLOSED LEFT SLOT COINS 400 CENTER SLOT COINS 0 RIGHT SLOT COINS 325 TOTAL COLLECTION 725 SUBTOTAL $181.25 CLEAR SUBTOTALS RETORN TO MAIN MENU
Typical Coin Bookkeeping Screen, Page 2
GAME AUDITS GAME AUDITS SHOW YOU AT A GLANCE if game settings are bringing you a satisfactory return on your investment! Only games by WILLIAMS
ELECTRONICS have this menu-driven feature. Think of it as a unique way to keep your NARC game the leader of the pack when it comes to earnings...location after location, week in and week out!
ENTERING AUDIT MODE. Open the coin door and press ADVANCE. You'll see the main test menu on the CRT screen. Use either joystick to highlight GAME AUDITS. Now select GAME AUDITS by pressing any player panel button.
TOTAL PLAYS EXTRA MEN EARNED HOURS OF SINGLE PLAY HOURS OF DUAL PLAY TOTAL HOURS OF PLAY AUG, "PLAYER" GAME TIME (MIN.)} AUG. ELAPSED TIME/PLRY¥
NET AUDIT PAGE RETURN TO MAIN MENU
Typical Game Audits Screen, Page 1
The first GAME AUDITS page will appear. Total plays and the number of extra men that players earned are provided here. The remaining entries on this page relate aspects of gameplay to time. The second audit page relates how many times players achieved each wave (difficulty level). Now let's examine two audit entries...
AVERAGE TIME PER CREDIT: TWO MINUTES. Your most important figure on the AUDITS pages is AVG. PLAYER GAME TIME (MIN.). You'll want to
pay special attention to this figure every day for this reason: Thorough field and factory research has shown that two-minute games both satisfy players and keep the quarters flowing.
DITS REVISION HH
Ss GAMES STARVED WAVE 1 REACHED WADE 2 REACHED WAVE 3 REACHED WADE 4 REACHED WAVE 5S REACHED WAVE 6 REACHED MR. BIG CONQUERED eoonoeos
PREDIGUS AUDIT PACE RETURN TO MAIN MENU
Typical Game Audits Screen, Page 2
If games aren't running about two minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your game-playing public. \t's easy, and we'll talk about that subject in a moment.
Meanwhile, another very useful figure is AVG. ELAPSED TIME/PLAY. You'll find this figure on the first GAME AUDITS page. This number tells you approximately how long your game must operate before earning a quarter. (There's a trick to AVG. ELAPSED TIME/PLAY: Simultaneous two-player games cause this figure to be smaller than AVERAGE "PLAYER" GAME TIME.)
EXCLUSIVE GAME ADJUSTMENTS Profitable games are adjusted to their playing public. NARC games provide you with numerous gameplay options. Like Audits and Game Bookkeeping, Game Adjustment selections are menu driven. This technique is
quick, effective, practical. It permits you to make the regular adjustments your location needs. Here's the easy, step-by-step procedure...
[]1.
12. Press ADVANCE to enter the main test menu (described earlier).
Using either joystick, move the selection arrow.down to GAME ADJUSTMENT.
To select GAME ADJUSTMENT, press any player panel button. Now you'll see the adjustment screen.
Use either joystick to highlight the feature you desire to adjust.
. To select that feature, press any player panel button.
Use either joystick to alter the value of an adjustment. (The joystick causes YES-NO settings to toggle between YES and NO.)
To return to Game-Over Made, follow menu selections on your screen.
RETUAN TO MOON MENU STANDARD PRICING CUSTOM PRICING GAME DIFFICULTY EASY BUY-IN LIVES PER PLAY ROCKETS PER PLAY EXTRA MAN EVERY LAST ENTAA MAN ATTRACT-MODE SOUND AUTO HIGH SCORE RESET VIOLENCE LEBEL RETURN TO MAIN MENU
Typical Game Adjustment Screen
GAME-TAILORING SUGGESTIONS Here are some game-tailoring suggestions. Please remember this: Easy settings tend to prolong game time, while conservative settings tend to reduce it. Try to provide players with a two-minute game. These selections appear on the GAME ADJUSTMENT menu...
GAME DIFFICULTY. Choose the appropriate GAME DIFFICULTY level for your location. For longer games, make gameplay easier. For shorter games, elect more challenging play. (7 = easiest or extra liberal, 5 = factory setting, 10 = hardest or extra conservative.)
eLIVES PER PLAY. For shorter games, decrease the number of LIVES PER PLAY. For longer games, increase it. (7= easiest or extra liberal, 3= factory setting, 1= hardest or extra conservative.)
*ROCKETS PER PLAY. For shorter games, decrease the number of ROCKETS PER PLAY. For longer games, increase it. (10 = easiest or extra liberal, 5 = factory setting, 1 = hardest or extra conservative.)
*EXTRA MAN EVERY. This value is the score players must achieve before the game awards an extra man. For shorter games, increase EXTRA MAN EVERY. For longer games, reduce this value. (50,000 = easiest or extra liberal, 100,000 = factory setting, 500,000 = hardest or extra conservative.)
*LAST EXTRA MAN. Pick the appropriate LAST EXTRA MAN level. (Off = factory setting, 5,000,000 = average, 100,000 = hardest or extra conservative.)
*SELECT GAME PRICING and specify standard or custom settings.
*SELECT AUTO HIGH SCORE RESET. This feature allows new players to display their initials on the High Score Table. Note: Initials entered within 750 games of table reset remain for 750 extra games.
NARC Sewice Manual 1- 20
GAME UTILITIES OPERATOR MESSAGE. As observed, some adjustments affect your game's profits. There are others that make your location run smoother. These are the NAAC Utilities. From the same efficient menu system, you can enter an advertising message for the game to display. (Your message replaces the player coin message.) Also, you can clear credits, coin counters or audit totals, or reset high scores. You can return all options to their factory settings. Or you can restore factory setiings and simultaneously clear and reset.
The Utility menu is available from the main test menu. Follow the screen prompts (or review procedures offered previously in this manual).
UTILITY MENU NARC REVISION HAH
SELECT ACTIVATE WITH ANY BUTTON
SET OPERATOR MESSAGE CLEAR CREDITS CLEAR COIN COUNTERS CLEAR GAME AUDITS RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE RETURN TO MAIN MENU ENTER YOUR OWN MESSAGE 10 APPEAR IN THE ATTRACT MODE
Typical Utility Menu Screen
Game Pricing
NARC software includes a choice of standard or custom pricing methods. Standard settings are very easy to choose and use. In less than a minute, you can reprogram game pricing. Your game provides over 40 standard settings. Screen prompts assist you and the game's computer sets eight different functions simultaneously. Custom settings offer more flexibility, but you must adjust the eight functions yourself. If you want to invent your own a pricing scheme, use custom settings.
Tables in this section list standard pricing schemes and suggest custom schemes. If you opt for custom pricing, please consult the formulas provided later.
STANDARD SETTINGS STANDARD PRICING allows a shorthand method of setting the pricing functions. This option is available from the main menu by selecting GAME ADJUSTMENT. When the GAME ADJUSTMENT screen appears, you'll see the listing for STANDARD PRICING. This option presents an easy, abbreviated method of setting pricing functions.
HOW TO USE STANDARD SETTINGS. Just follow these steps...
[] 1. On the GAME ADJUSTMENT screen, move the highlighted bar to STANDARD PRICING.
[] 2. Enter STANDARD PRICING by pressing any player panel button.
[]3. To modify the pricing scheme, use the joystick and browse through standard selections. Later in this chapter, standard selections also appear in a table.
[] 4. When you locate the desired pricing scheme, enter it by pressing any player panel button. The game responds by installing a
corresponding standard setting. Eight pricing functions are automatically set to produce that standard.
[] 5. To return to Game-Over-Mode, follow the screen prompts.
Standard Pricing Table
COIN MECH GAMES/PRICE COUNTRY Twin 1/25¢, 4/$1 Quarter 1/50¢, 2/$1 1/50¢, 3/$1
Quarter, Dollar, Quarter 1/50¢, 3/$1 1/50¢, _4/$1 USA 1 USA 2 USA 3. Sh
USA 7 USA 8 1/1, 6/5DM
» S/10F 2/5, 4/10F 1/5, 3/10F 5 Franc, 10 Franc
12x1 OF 4/5, 3/10F, 1/5, 2/10F, 5/2x10F 113x1F, _2/5F 1 Franc, 5 Franc
1 France, 5 1F, 6/5! Franc TMF, 7/5F TAF, 8/5F 500/500 Lire 20p/50p ance 1 France 2 France 3
France 8 France 9
Switzerland 2 Switzerland
Standard Pricing Table, Continued | ecw | GAMES/PRICE COUNTRY
| 25 Peseta/ | 1/2x25P, 5/100P | Spain 1 |
| 100 Peseta | 1/25P, 4/100P | Spain 2 |
20¢/$1 i
100Y 5 Schilling/ | 1/5Sch, 2/10Sch Austria 1
| 10 Sel | 1/2x5Sch, 3/2x10Sch | Austria | _2 |
20¢/20¢ : dt 1/2x20¢ New Zealand 2 JAHFI, 3,
[sei G | 1i2dse, 4/1G
CUSTOM SETTINGS HOW TO USE CUSTOM SETTINGS. Custom pricing is a bit more involved than standard pricing. For that reason, if your pricing scheme is listed on the Standard Pricing Table, use standard pricing.
However, the Custom Pricing Table also provides numerous examples that you might want to try. Read down the table to find an appropriate selection. Then, reading across the selection, enter the values. You can also create your own settings. Formulas provided later should simplify your work.
(16. CUSTOM PRICI NARC BEUISION 8.4K
LEFT CHUTE UNITS CENTER CHUTE UNITS RIGHT CAUTE UNITS UNITS/CREBIT UNITS/BONUS MINIMUM UNITS REQUIRED CREDITS 10 START CREDITS 10 CONTINUE COIN PAGE HELP SHOW CREDIT FRACTIONS COINS PER DOLLAR FREE PLAY MAHIMUM CREDITS RETURN TO ADJ. MENU
Typical Custom Pricing Menu
. On the GAME ADJUSTMENT screen, move the highlighted bar to CUSTOM PRICING.
. Enter CUSTOM PRICING by pressing any player panel button. The game responds by displaying the CUSTOM PRICING screen.
. Now you can modify any of eight pricing functions. The first of these is LEFT CHUTE UNITS, and the last is CREDITS TO CONTINUE.
Use the joystick to move the highlight bar down to first function you want to change. Notice that as you select a function, its definition appears on the screen. (Function definitions also appear later in this manual.)
To enter the function, press any player panel button.
. Select a new value with the joystick.
To enter the new value, press any player panel button.
{]7. Set the remaining values as desired.
{] 8. To return to Game-Over Mode, follow the screen prompts.
{]9. Check your work! Anyone can make a calculation error. But if you don't do your homework, that error could be expensive. Feed a handful of coins into the game and verify that game pricing performs satisfactorily.
PRICING FORMULAS Use this section to help you determine new custom pricing schemes. A simple ratio is the key. With this ratio, you can translate your scheme into entries for the CUSTOM PRICING menu.
THE PRICE OF ONE GAME can be derived from the number of games per price. The games per price relationship is equivalent to the ratio S : VC, where...
S = CHUTE COIN UNITS (left, right or center) V = COIN VALUE (for example, 25¢) C = UNITS REQUIRED FOR CREDIT
CUSTOM PRICING EXAMPLES. At factory settings with quarter chutes, the variables produce 1 : 25 x 1 or one game for a quarter.
If an operator wants to allow one play for a quarter but wishes to encourage multiple game-playing, he may enter:
¢"{" in the LEFT CHUTE COIN UNITS function ¢"4" in the CENTER CHUTE COIN UNITS function °"{" in the RIGHT CHUTE COIN UNITS function *"{" in the UNITS PER CREDIT function
- "0" in the UNITS/BONUS function
NARC Sewice Manual 1- 26
+ "2" in the MINIMUM UNITS REQUIRED function
These values allow one game to be played for a quarter, but ONLY when two or more games are paid for at a time. Incidentally, the "4" in CENTER CHUTE COIN UNITS allows four games per dollar coin. (Use this setting when you have a dollar bill acceptor connected to the center chute wiring. Connection instructions appear later in this chapter.) See "2/50¢, 4/$1" in the Custom Pricing Table.
Custom Pricing Table EFT | CENTER] RIGHT COIN- HUTE | CHUTE | CHUTE! MIN.
| DOOR | ‘OIN | COIN | COIN | UNIT | NITS/ UNITS |
MECH GAMES/PRICE UNITS UNITS ONUS | REQ'D
| i | 1/25¢, | 5/$1 | 4 | 1 |
| 1/25¢, 3/50¢, 6/$1 | 4 | 1 |
Quarter —
1 25¢,_ 1G] Twin Coin! ee
| 5 Unit | 13, 2/5 Coins | 15 |
CUSTOM PRICING TERMINOLOGY *LEFT, CENTER, RIGHT CHUTE UNITS. Abbreviations for Left, Center or Right Chute Coin Units. Coins don't buy games directly. Instead, the game exchanges each inserted coin for a number of chute coin units. "CHUTE UNITS" specifies the value of a coin in chute coin units. The game tallies chute coin units for each chute separately (left, right or center). That is, LEFT CHUTE UNITS is a separate adjustment from CENTER CHUTE UNITS.
eUNITS/CREDIT. Coins buy units, and units buy games. UNITS/CREDIT is the price of one credit (game) in coin units.
*UNITS/BONUS. The number of units that must be purchased before a free (bonus) credit is awarded.
*MINIMUM UNITS REQUIRED. The smallest quantity of coin units that can be converted into credits. No games will be awarded until the minimum units have accumulated. (See the second Custom Pricing Example, above.)
-CREDITS TO START. The number of credits each player needs before he can begin a game.
*CREDITS TO CONTINUE. The number of credits each player needs to continue playing a game.
*COIN PAGE HELP. When you use standard pricing, a message appears on the credits screen. Setting COIN PAGE HELP to NO disables the message. The operator message overrides the pricing message. (You can compose an operator message by employing the Utility Menu. That menu is accessible from the Main Menu. See Game Utilities.)
«SHOW CREDIT FRACTIONS. This display function may be set to yes (enabled) or no (disabled). \f YES, when the display of credits (games) purchased appears, purchased game fractions also appear. If such fractions make coin calculations easier for your players, then enable the feature. Where coins or custom pricing present complex fractions, we recommend that you disable this feature. (Your game creates the fraction by dividing chute coin units into purchased UNITS/CREDIT.)
*COINS PER DOLLAR. The TOTAL COLLECTIONS (COIN BOOKKEEPING) screen is based on this coins-per-dollar function. (For example, you might specify here that a dollar is worth five of your tokens. That way, the game computer can even figure total collections for tokens!) To disable the display of money totals, set this function to zero.
«FREE PLAY. Setting FREE PLAY to "YES" allows unlimited play without inserting coins. The factory setting is "NO."
-MAXIMUM CREDITS. This is the coin counter limit. If inserted in the coin chutes, additional coins will be lost. The factory setting is 30.
Installing A Dollar Bill Acceptor
On U.S. (2-slot) coin doors, wiring for the absent center coin chute is provided. You can use this wiring to connect your dollar bill acceptor to the game's Interface Board. Here's the step-by-step procedure...
[]1.
[]2.
[]3.
(15.
(17. Locate connector 8P2/8J2. You'll find this 15-pin connector just inside and above the coin door.
Find the white-green wire on the plug (female, 8P2) side of the connector. This wire is connected to pin 9.
Crimp a pin onto the positive switch lead from your bill acceptor.
. Insert the pin into the pin 9 hole on jack (male) 8J2.
Find the ground switch lead from your bill acceptor. Splice this lead to a green-brown wire from either of the other two acceptors. Any of the green-brown wires will suffice.
. Set the bill acceptor to one pulse per dollar.
ROWE brand $1/$5 acceptors: Turn on DIP Switch 4 ("Slow Pulse Train"). Other brand acceptors: Output pulse width should fall between 16 and 300 milliseconds. Distance between pulses should exceed 200 milliseconds.
[] 8. Set your game's STANDARD PRICING to one of the USA options, 5 through 8.
[] 9. Test time! Run coins through the quarter chutes and bills through the new bill acceptor.
Chapter 2. Service
Procedures
Introduction
Operating the
Diagnostic Mode Tests
Built-In Test Procedures
Troubleshooting Tables
Introduction
Your NARC video game is equipped with numerous diagnostic features. These features are designed to aid you in maintaining top game performance. Your game offers two types of tests: First, whenever you turn it on, the game performs Power-Up Tests. Second, you may initiate Diagnostic Tests with the game's controls. Tests include the following...
- Switch Test
- ROM Board Test
- CPU Board Test provides a board image, showing major chips: + Video RAM
- Scratchpad RAM + DMA Custom chip
- Color RAM « CMOS RAM and Battery
- GSP Microprocessor 4.Sound Test
- Monitor Patterns +Bar/Dot Crosshatch Test “RGB Purity Screens Colors Bars, indicating gun levels
- Burn-In Test (Automatic, repeating sequence of other tests)
Power-Up Tests
CPU BOARD TEST RUG PATTERN. At power-up, a scanning "rug" pattern appears on the game's screen. During this display, the game checks Video RAM chips. These include Video RAMs U42 through U49 and U68 through U75. A stationary, striped pattern replaces the scanning rug. This pattern is an artifact of the testing process. (/t reproduces the last two lines of the rug pattern stored in Palette Latch U13/U30.) Since DMA U77 loads the Video RAM, the test also demonstrates DMA condition.
CPU BOARD DRAWING. Following the stripe pattern, an assembly diagram of the CPU Board appears very fleetingly. This diagram indicates test passage by Video RAM chips checked during the rug pattern (above). Also tested is main microprocessor (GSP) U18. Other tested components include Scratchpad RAM (U60 through U63) and Color RAM (U7/U41). The game checks CMOS RAM U65 too. As they check good, the screen depicts the chips in green. Bad chips appear in red.
BAD CHIP NUMBERS DISPLAYED. If the game finds an error, you'll see the message "RAM ERRORS DETECTED. PRESS ANY KEY TO RETURN TO MENU." Normal games display the message "NO RAM ERRORS DETECTED. PRESS ANY KEY TO RETURN TO MENU."
LED INDICATOR. If RAM damage is extensive enough to prevent a screen display, examine the CPU-Board LED-indicator. The game aitempts to display bad chip numbers (digit by digit) here too. The error code on the indicator corresponds to RAM chip number. This code appears one character at atime. The code begins with "E" for error. The next two digits refer to the chip number of the first bad chip detected. Corresponding chip numbers are screened on the game's CPU Board. (NARC games display these letters and numbers upside-down.)
If the game displays a RAM error, check the indicated RAM's DC power voltage...
+ 4461 DRAMs: Positive five volts on pin 12 (ground at pin 24).
+ 4464 DRAMs: Positive five volts on pin nine (ground at pin 18).
None of these pins should have more than a few millivolts of AC on it. Never replace a RAM chip until you prove that these voltages are normal!
SOUND TEST RAM Power Pins
Ground
TWO TONES. While the rug pattern is scanning, the game normally sounds two different tones. These indicate readiness of Music System U1/U2/U5, etc. and Sound Effect System U33/U34/U38, etc. The Music System's readiness indication is a "gong" note. The Sound Effect System employs an "electric guitar" note. (The gong occurs first.) The two systems reside on the Sound Board. If you don't hear two different tones, your game probably has a Sound Board problem. Here's a rundown of what you might hear and what it means...
+ No sound:
*1gong sound:
¢1 guitar sound:
°2 different sounds:
+ 2 identical sounds: Sound Power Supply fuse F2/F3, broken cable, dead clock CR1, dead amp U32/U41, etc.
Slave (Sound Effect) System U1, etc. okay; fault in Master (Music) System
Master (Music) System U1, etc. okay; fault in Slave (Sound Effect) System
Master System U1 and Slave (Sound-Effect) System U33, etc. okay
Sound ROM or RAM errors. (Run Diagnostic Mode Sound Test.) More than two identical sounds may occur.
ROM TEST TEST PROCESS. The game compares numbers stored in Program ROMs U23 and U41 with calculated ROM checksums. Each chip has its own checksum. Ifthe corresponding number from Program ROM matches, the chip passes the test.
ROM BOARD DRAWING. A ROM Board drawing appears. Initially ail the chips are shown in gray. Then as they test good, checked ROMs are depicted in green. Bad chips appear in red. Unused chip locations remain gray. These unused locations include U25, U43, U61 and U79. Tested chips include U23 through 40 and U41 through U58. Also tested are U59 through U76 and U77 through U94.
If the game finds an error, you'll see the message "ROM ERRORS DETECTED. PRESS ANY KEY TO RETURN TO MENU." Normal games display the message "NO ROM ERRORS DETECTED. PRESS ANY KEY TO RETURN TO MENU."
LED INDICATOR. The game's LED indicator on the CPU Board presents a backup display of failure messages. The error code on the indicator corresponds to ROM chip number. This code appears one character at a time. The code begins with "E" for error. The next two digits refer to the chip number of the first bad chip detected. Corresponding chip numbers are screened on the game's ROM Board. (NARC games display these letters and numbers upside-down.) Power down and replace bad chips.
ROMS U23 AND U41. The ROM Test can operate if only ROMs U23 and U41 are good. This feature is useful in troubleshooting. For instance, an unknown ROM may be pulling bus lines low. If so, you can remove all the ROMs except U23 and U41 and rerun the test.
If the test now runs normally, the bus itself is okay. But one or more ROMs must be bad. Replace the top row of ROMs (U23 through U40) and retest. If these ROMs test good, replace the next row (U41 through U58) and retest.
NARC Senice Manual 2- 5
(Proceed one row at a time until you find the bad row.) If a row brings down the bus, remove all but one chip. Chip by chip, rerun the test until you locate the chip that brings the bus down. If the bus is bad, use a logic probe to check other devices on the bus. Likely culprits include address decoders, buffers, latches and transceivers.
CMOS BATTERY TEST DEFAULT ADJUSTMENTS RESTORED. Your game includes a CMOS RAM that stores temporary data such as scores and adjustments. If CMOS contains spurious data or the battery fails, the game prompts: "INVALID GAME SETTINGS." Then you must open the coin door so that CMOS can be cleared. At that point, the system displays the message "DEFAULT ADJUSTMENTS RESTORED." Now, step the game into Game-Over Mode: First, press ADVANCE. Then use the joystick and player panel buttons to enter Game-Over Mode. If the game displays "INVALID GAME SETTINGS" whenever you power it up, suspect the battery.
If you suspect a bad battery, power down and replace it. Otherwise the game won't remember pricing and game adjustments you've entered. NARC games employ a three-volt, round lithium cell (RAYOVAC BR2325). This battery resides on the CPU Board, with the "+" terminal facing upward. (That is, with minus toward the board). With power off, CMOS RAM U65, pin 28 should measure 3VDC (at least 2.8V). With game power off, you can check this voltage with a multimeter. After you replace the battery, step the game into Game-Over Mode one more time. The game should retain your next settings.
GAME-OVER MODE WATCH FOR THE HIGH SCORE TABLE. Ina correctly running game, tests will be followed by the the High Score Table and a repeat of the two Sound Board tones. When you see the High Score Table, your game has entered Game-Over Mode. This is a normal mode of operation. If failure messages come up on the screen instead, initiate Diagnostic Mode Tests.
NARC Sewice Manual 2- 6
Diagnostic Mode Tests
INITIATING DIAGNOSTIC MODE TESTS You can initiate Diagnostic Tests from the game's coin door: First, open the coin door. Then locate the white ADVANCE button. It's mounted ona bracket a few inches behind the door. Press ADVANCE. The game responds by displaying the main menu. Now using the joystick, move the highlighted bar to DIAGNOSTIC TESTS. Press any player panel button. This time, the game displays its diagnostic menu.
SELECTING AND ENTERING OPTIONS. To select an option you desire to investigate, move the joystick up or down. Watch the highlighted bar on the screen menu. This bar illuminates the selected option. You can enter the highlighted option by pressing any player panel button.
IF THE PLAYER PANEL EVER FAILS, ADVANCE can operate diagnostic and bookkeeping functions. For details, see the Chapter 1 section entitled Game Adjustments, Bookkeeping, Diagnostics.
NARC TEST MENU NARC REVISION #.#
SELECT WITH UP/DOWN STICK ACTIVATE WITH ANY B
UTILITIES FHIT TO GAME OVER
Typical Main Test Menu
SWITCH TEST The monitor displays 21 circles in the approximate positions of game switches. Near each circle is a switch name. When you close a working
switch, the game highlights that switch's circle. Highlight colors match player button colors. Check for switches that are stuck open or closed.
DIAGNOSTIC TESTS NARC REVISION HK
SELECT WITH UP/DOWN STICK ACTIVATE WITH ANY BUTTON
Switch Test BOM BOARD TEST ceu BoaRD TEST SOUND BUARD TEST MONITOR PRITERNS RUN BURN-IN TEST RETURN TO MAIN MENU
Typical Diagnostic Menu
Each joystick has four switches (one in each compass direction). As necessary, clean or replace malfunctioning parts.
"CUT FOR GERMAN" and "CUT FOR FRENCH" jumpers on connecior 3P2 are depicted as switches. These will normally remain closed for U.S. games. If the German or French jumper is cut, it will appear as open.
To exit the Switch Test, press ADVANCE.
ROM TEST This test is equivalent to the Power-Up ROM Test. Refer to ROM Test above. Chip errors are displayed on the CRT and the LED readout on the CPU Board. If achip is bad, the LED error code corresponds to its chip number. Chip numbers are screened on the game's circuitboards.
CPU BOARD TEST This test is equivalent to the Power-Up CPU Board Test. Refer to CPU Board Test above. Chip errors are displayed on the CRT and the LED readout
on the CPU Board. Ifa chip is bad, the LED error code corresponds to its chip number. Chip numbers are screened on the game's circuitboards.
SOUND TEST Tested chips include RAM U34, ROMs U35 through U38, CVSD U30, DACs U10 and U20. Also checked are Yamaha Synthesizer chip set U7/U8 and microprocessors U1 and U33.
SYNTHESIZER AND DIGITIZER. The NARC Sound Board includes two 68BO9E microprocessors, U1 and U33. Microprocessor U1 controls the Master or Music System. This system includes Yamaha Synthesizer U7/U8. Microprocessor U1 also supervises communications with the GSP. (The GSP is the main game system on the CPU Board.) Tests refer to the first sound system or its components as the Synthesizer. The second Sound Board microprocessor (U33) controls the Slave or Sound Effect System. This includes a type 7224 Sound Effect DAC and a type 55536 CVSD (speech) chip. Tests refer to this second sound system or its components as the Digitizer.
SYNTHESIZER AND DIGITIZER TROUBLESHOOTING. Note that the GSP directly controls only the Music System. Meanwhile, the Music System controls the Sound System. Only the Music System (Synthesizer) communicates directly with the GSP. That is, if the Synthesizer's down, the Digitizer can't respond to GSP sound calls. Consequently, if the Digitizer doesn't work, be sure the Synthesizer's okay before troubleshooting the Digitizer!
SYNTHESIZER TEST. The Synthesizer Test indicates that the Synthesizer is "OK" or "SYNTHESIZER DOES NOT RESPOND.” The game also provides the status of other chips (see below). Synthesizer response depends on a good connection to the main microprocessor (GSP). If you receive the message "SYNTHESIZER DOES NOT RESPOND," interboard wiring might be at fault. Check the cable between the CPU and Sound Boards. Also check bus buffer chips connected to both ends of the cable.
SOUND BOARD TEST RC REVISION H.H
SYNTRESIZER TEST DIGITIZER TEST PLAY SYNTHESIZER PLAY DIGITIZER BACK TO DIAGNOSTICS MENU RETURN TO MAIN MENU
Typical Sound Test Menu
The game also employs the Synthesizer for other tests. For that reason, tunning the Synthesizer Test first may save you some troubleshooting steps.
The Synthesizer Test causes your game to produce “electric guitar” tones. These tones may indicate chip failures. Consult the list below.
*0 Tones: Synthesizer MPU U1 not responding or ROM U5 bad *t Tone: Synthesizer OK. Error message? Check 10P2/J2 (handshake) cable. *2 Tones: RAM error U2 *3 Tones: ROM error U5 *4 Tones: ROM error U4
DIGITIZER TEST. The Digitizer can't communicate directly with the GSP. For that reason, the Synthesizer handles the Digitizer Test's GSP-to-Sound Board communications. The Digitizer Test has its own menu. "Gong" tones indicate failure of the test by various devices...
*0 Tones: Check ROM U38 or Synthesizer (Music) System *1 Tone: Digitizer (Sound Effect) System OK *2 Tones: RAM error U34 *3 Tones: ROM error U38 *4 Tones: ROM error U37 *5 Tones: ROM error U36 *6 Tones: ROM error U35
PLAY SYNTHESIZER allows you to test the game's sound lines by triggering game sounds. Pressing a player panel button activates each next sound. For diagnostic purposes, the game also provides a ramp wave and a sinewave. Here's the entire list..
-Narc Rap «Windshield Smash Driving Music *Car Horn *Narc Theme *Bug Squash “The "Stick" *Sizzle Helicopter *U10 DAC Ramp wave ¢Kinky Pinky °U7/U8 YM2151 Sinewave
When you press a button, the system pulses sound and strobe lines low. The result is a sound. Each sound represents a combination of low sound and strobe lines (sound call). \f a sound is missing, one or more lines are probably stuck high or stuck low. If two lines produce the same sound, they're shorted together.
If all sounds are missing, the strobe signal might be absent. Whenever the system pulses a sound line, it must also pull down a strobe line. Otherwise you won't hear any sound. The strobe lines select either the Sound or the Music Microprocessor. The game employs other bits on the Sound-Selection Bus for communications. For instance, the CPU Board's GSP (main system) can reset the Sound Board. Over a separate line, the Music Microprocessor can send a handshake signal to the GSP. NARC games only employ this handshake signal during tests.
PLAY DIGITIZER allows you to test the game's sound lines by triggering game sounds. Pressing a player panel button activates each next sound. For diagnostic purposes, the game also provides a ramp wave and a waveform from CVSD U30. Here's the entire list..
*Gunshot *Dog *Dumpster Man “You die, Cop! *Oh no, the Narcs Man «Mr. Big Laugh *Dr. J Scream *U20 DAC Ramp Wave -U30 CVSD Waveform
USING "PLAY SYNTHESIZER" AND "PLAY DIGITIZER" TESTS NO SOUND: Check the sound-select inputs at chip U6 on the Sound Board. (Pins 3, 4, 7, 8, 13, 14, 17 and 18.) During the "Play Synthesizer" or "Play Digitizer" Test, look for pulsing. Also check for shorts between sound lines. If two sound lines produce the same sound, you have a short.
STILL NO SOUND: Turn the volume contro! all the way up and turn on the game. Momentarily run your fingers around the pins of preamplifer chips U1, U21 and U39. Also use your fingers to probe the quarter-watt resistors near these chips.
- If you hear a click or hum, the amplifiers, volume control and speaker are okay.
- If you don't hear anything, turn the volume conirol halfway up. Now repeat the test.
MONITOR PATTERNS Monitor Patterns assist you in isolating problems to the game computer or its analog monitor. Furthermore these patterns are useful in setting up new monitors, or in troubleshooting old ones.
MONITOR PATTERNS NARC REVISION H.H
RED SCREEN GREEN SCREEN BLUE SCREEN COLOR BARS CROSSHATCH PATTERNS BACK TO BIAGNOSTICS MENU RETURN TO MAIN MENU
Typical Monitor Patterns Menu
RED, GREEN AND BLUE SCREENS (three solid-color patterns) are intended for monitor purity adjustments. You can also use these patterns for checking Color RAMs (!Cs U7 and U41 on the CPU Board). If these screens show contaminated colors, degauss the monitor. If purity is still flawed, adjust the purity magnets. (For the adjustment procedure, consult your monitor manual.)
A purity screen may be missing some colors or may have vertical lines through it. If so, your game might have a faulty Color RAM U7 or U41. See the illustration below. (Please don't confuse the purity screens with the crosshatch pattern or color bars pattern. These last two patterns are supposed to have vertical lines!) Before pursuing monitor adjustments or RAM replacement, degauss your monitor.
COLOR BARS. Use the Color Bars for monitor adjustments and for checking Color RAMs. Each bar shows a color in 32 levels of intensity (brightness). That is, the bars serve as both a color and brightness reference. This reference eases adjustment of color drives and cutoffs, screen and black-level controls.
If colors are missing or the wrong colors are displayed, you may have a bad Color RAM. From the left side of the CRT, here are the colors you should see: Red, green, blue, black, white, yellow, cyan and magenta.
As observed, each color bar is composed of 32 hue segments. The brightest hues should be at the top of the screen. The darkest hues should be
at the bottom. Adjacent hues should have the same brightness.
Before pursuing monitor adjustments or RAM replacement, degauss your monitor. Then as necessary, adjust your monitor for best brightness and contrast.
THE CROSSHATCH PATTERN aids the technician in converging your game monitor.
RUN BURN-IN TEST BURN-IN MODE permits continuous ROM, RAM and CMOS RAM tests. To detect failures that only appear after numerous checksum comparisons, such repetition is necessary. If game software locates an error, Auto-Cycle Mode aborts and a failure message appears. Here's the procedure for initiating Burn-In Mode...
- Enter the Diagnostic Menu by displaying DIAGNOSTIC TESTS.
- Move down to RUN BURN-IN TEST.
- Press any player panel button.
- The game prints "ARE YOU SURE?" Select "YES" by moving up.
- Press any player panel button.
- To enter Game-Over Mode, turn the game off and on.
TROUBLESHOOTING TABLES
Troubleshooting procedures for most types of malfunctions can be performed with minimal test equipment or merely are covered below. Our troubleshooting algorithm begins with by observing the game, Note: Certain malfunctions may Power-Up and continues until Game-Over Mode. Procedures inhibit the game's diagnostic or display faculties.
POWER-UP TESTS
NO VIDEO OR GENERAL NO INITIAL VIDEO CHECK SWITCHING ILLUMINATION (RUG PATTERN) POWER SUPPLY
- Check fuse 6F1 on transformer chassis.J(1) Press the RESET button on CPU (1) Swap Power Supply with one from
| (2) Check +5VDC on CPU Board. On: | Board. | known-good game. |
Proceed with step 3, Off: Check Switching (2) Try CPU Board and ROM Diagnostic- | (2) If game plays, problem is in Power
| Power Supply. | Mode Tests (see below). | Supply. |
| (3) Check power connectors: 1P1/J1, | (3) If these tests don't turn up the | (3) If game doesn't play, check power |
2P3/J3, 3P116P 1/J1, 6P2/J2, 6P3/J3, problem, check Switching Power Supply. } transformer with voltmeter.
| 6P4/4 | check Power Supply Board. | (4) If known-good power supply is unavail- |
- If all the above don't turn up the prob- able for tests above, check +5V output on em, check Switching Power Supply. game supply. Output must be within 5% of rated 5V, with less than 0.1% AC hum.
TESTED CPU BOARD VIDEO YOUR REACTION PART LED INDICATION SHOULD BE...
- Scanning rug pattern If any video (see left) is missing or error
| 8 blinking, h | tal | (2) Stripe pattern | message is displayed, roceed to Diagnostic |
| cognate ipovehin | (3) CPU Board drawing (very briefly) | Mode Tests. |
tests passed) (4) ROM Board drawing
- Game-Over Mode 3 blinking, horizontal
| seamerita (Power-up | "INVALID GAME SETTINGS" | (1) Open coin door. |
tests passed) een ent eee et anneeeeneceenneeenane: “DEFAULT ADJUSTMENTS RESTORED" | (2) Press ADVANCE, "COIN COUNTERS CLEARED" (3) CMOS is OK. Use joystick anda game "GAME AUDITS CLEARED" button to step game into Game-Over Mode. “HIGH SCORE TABLE RESET" (4) Other messages: Perform DiagnosticTests.
| Batter | 3 blinking, | horizontal | J | "INVALID GAME SETTINGS" | (1) Tum power off. (2) Check or replace 3V |
| ’ | plies tial | lithium cel on CPU Board. (3) If problem |
persists, proceed with CPU Board Test by tests passed) ) putting the game into its Diagnostic Mode. (See DIAGNOSTIC MODE TESTS.)
| Memory- | ing, | hori | "INVALID GAME SETTINGS" | (1) Making and breaking Memory Protect |
Protect, parts (poner Interlock switch, check with VOM. (2) if faulty
Interlock replace switch. (3) Replace if faulty: rloc! tests passed) Reset/Watchdog US55 or CMOS RAM U65 on CPU Board.
| £75 (Spurious | (1) Scanning rug pattern | (1) Turn power off. (2) As test, temporarily |
| indication of RAM | (2) All ROMs test bad | replace DMA U77 with good part. U77 is on |
- Program crash CPU Board. (CAUTION: Use chip-extraction failure 78) tool) (3) Run Power-Up Tests.
DIAGNOSTIC_MODE_TESTS
TEST & PROCEDURES
+ No LED indications are made for VIDEO
CRT indicates stuck switches. This chart relates switches and their Interface Board connectors. YOUR REACTION SHOULD BE...
(Refer to CABINET WIRING Diagram. Jacks 3J2 through 3J6 are on the
3J2 SWITCHES
PLAYER-1 START PLAYER-2 START FRENCH BIT GERMAN BIT MEMORY PROTECT] this test. + U.S. Games: CRT should indicate no switches closed. + Clear stuck switches. + Operate each switch and check for display of switch name. + Check for joystick switch closures in all four compass directions.
34 SWITCHES
PLAYER 1 UP PLAYER 1 DOWN PLAYER 1 LEFT PLAYER 1 RIGHT PLAYER 1 FIRE PLAYER 1 ROCKET, PLAYER 1JUMP. PLAYER 1 CROUCH! Interface Board.) 33 SWITCHES
PLAYER 2 UP PLAYER 2 DOWN PLAYER 2LEFT PLAYER 2 RIGHT PLAYER 2 FIRE PLAYER 2 ROCKET PLAYER 2 JUMP PLAYER 2 CROUCH 3J6 SWITCHES
ADVANCE VAULT SWITCH LEFT COIN CENTER COIN RIGHT COIN SLAM SWITCH
- INTERFACE BOARD SWITCH STUCK: Disconnect appropriate Interface Board plug 3P2, 3P3, 3P4 or 3P6, (Refer to chart at left).
- INTERFACE BOARD SWITCH DOES NOT OPERATE: Ground corresponding pin of 3J2, 3J3, 3J4 or 3J6. (Refer to Cabinet Wiring Diagram).
[] SYMPTOM REMAINS SAME: Faulty Interface Board.
[] SYMPTOM CLEARS UP: Switches or wiring are faulty.
TEST CPU BOARD VIDEO YOUR REACTION LED INDICATION SHOULD BE...
‘Three characters flash (one at ja time): “E“ means chip error. Then two-digit chip no. of first_bad_device detected.
Three characters flash (one at a time): “E" means RAM error. Then two-digit chip no. of first bad device detected. not appear.
"E65" means CMOS RAM lerror. FAILED." "ROM ERRORS DETECTED” and bad chip shown in red.
"RAM ERRORS DETECTED" and bad chip shown in red. With multiple RAM failures, this display may
“INVALID GAME SETTINGS. ATTEMPT TO RESTORE FACTORY SETTINGS HAS
- Turn power off. (2) Replace suspected chip. (3) Power up and retest game.
- Check for these normal voltages on indicated RAM chip: On 4461 chips, +5/pin 12; ground/pin 24. On 4464 chips, +5/pin 9; ground/pin 18. Wrong voltages: Check Switching Power Supply, power cables at 1P1/J1. Correct Voltages: Proceed. (2) Turn power off. (3) Replace suspected chip. (4) Multiple RAM failures: Check Switching Power Supply Jitst, Gee, POWER UP TESTS ssneasean
- With power off, check pin 28 of U85 CMOS RAM for 2.8VDC minimum. Present: Check or replace CMOS chip. Absent: Replace lithium cell. (2) With new lithium cell and power off, check for 3.0V (2.8V minimum) at pin 28. Still absent: Check for 3.0V at pins 1 and 2 of Reset/ Watchdog USS. Present at 1, absent at 2: Replace U55. (3) Power up and reenter diagnostics. If CMOS error message persists, check CMOS RAM memory protect and address decoding circuits. Use a logic probe.
NARC Sewice Manual 2- 17
DIAGNOSTIC MODE TESTS
Tests 4 and 5 feature sequential subtests. on your monitor. To step through subtests, follow menus displayed For these tests, no LED indications are provided.
- SOUND TEST AUDIO INDICATIONS YOUR REACTION SHOULD BE...
«PLAY SYNTHESIZER, DIGITIZER: if two sounds are the same, try a new sound cable. Two sound lines may be shorted together...
1P8/10P1 pin 1P8/10P1 pin 1P8/10P1 pin 1P8/10P1 pin 1P8/10P1 pin 1P8/10P1 pin 1P8/10P1 pin AP8/10P1 pin 10 1P8/10P1 pin 13 1P8/10P1 pin 18 1P8/10P1 pin 14 STROBE.M NMI.M RESET Alt Pertorm further tests (see below).
Checking Your Color RAM + The CRT produces a pattern of vertical color bars. Each color is shown in 32 hues.
+ Missing or repeated hues in the same bar: Color RAM fault. Color Bars as RAM_ Check major_parts indicated below. «SYNTHESIZER TEST (MUSIC): Bad part... 0 Tones Synth U1 or ROM U5. 1 Tone IOK;msg?10J1 cable 2 Tones 3 Tones 4 Tones *DIGITIZER TEST (SOUND EFFECTS, VOICES): Bad part... 0 Tones ROM U38/Synth 1 Tone Digitizer OK 2 Tones RAM U34 3 Tones ROM U38 4 Tones ROM U37 5 Tones ROM U36 6 Tones ROM U35 *Replace bad parts. Problem remains? Then check these related parts...
PART SPECIFIED | RELATED PARTS Xtal CR2,Inv U17, Decdr U14, AND U15, Latch U12
ROMs US, U4 Decoder U14, Latch U12, SIP resistor SR1 RQM_U38/Synth_| MPU_U1, RAM U2 RAM U34 MPU U33, NOR U24 ROMs U35, U36, | Decoder U25, U37, U38 Latch U23, SIP
- ARE SOME HUES MISSING? Do you see two identical hues? Check your CPU Board's Color RAM circuit. Failed
RAM U7 or U41, parts may include these chips: Latch U3 or U23, Color buffer U2 or U22.
- CHECK THE COLOR ANALOG CIRCUIT: CPU-Board resistors R2 through R16. Also monitor input tran-
+ Adjacent hues in different bars should have the same brightness. If not, adjust the gun drives on your monitor.
Monitor and Color RAM (As you watch (Note: Color order is shown at Test 7) sistors Q1, Q2, Q3, Q4 and associated passive circuitry.
- ANALYZE BY COLOR: -RED PROBLEMS: Check U7, U3, U2, R2 through R6. «GREEN PROBLEMS: Check U7, U41, U3, U23, U2, U22, R7 through R11, »-BLUE PROBLEMS: Check U41, U23, U22, R12 through R16. (All on CPU Bd.) Crosshatch Pattern| For monitor setup: linearity, convergence and focus.
Red Screen Optimize purity. +*Contaminated Green Screen colors: Degauss monitor. If Blue Screen necessary, adjust purity magnets. these screens, adjust your monitor) Color Pattern Missing color: Color RAM error. Color Bars (shown) + Double width + Half width +» Transposed + Missing mero
NARC Sewice Manual 2- 18 Adjust monitor drive, cutofi, screen and black-level controls. Symptoms at left suggest a fault in one of these: U3/U23, U2/U22, R2 through R16.
TROUBLESHOOTING YOUR SOUND BOARD SYMPTOM TEST AND PROCEDURES Missing Sounds; |[ ] Check sound-select inputs on Sound Board Ne Sound-Step 1 Condition and Your Action (Assumption: Input Section Failure) Reset pulse -RESET at 1 or U33, pin 37 Logic probe (Game on and in Test 4, “Play Synthesizer’ subtest) +HIGH (except first second after turn-on)--proceed +LOW--Stuck reset line. Unplug 10P1, power down and up and retest. *STILL LOW--To isolate the bad chip, remove reset pins from sockets, one at a time (below). Retest after each removal... Ut-pin 37, U33-37, U10-17, U20-17, U7-3, U8-7; replace bad chip and reinsert pins
+At flip-flop U26, pins 3, 8 Logic probe (Game | -PULSING--proceed on and in Test 4, *SOME LOW--check connectors 10P1/J1, “Play Synthe- 1P8/J8, foils sizer" subtest) “STILL LOW--perform CPU Board checkbox below *CPU Board OK--replace the Sound Board sLatch U6, pins 3, 4, IC with the stuck-low pin 7, 8, 13, 14, 17, 18 *PINS OK, NO SOUND--Check resistor pack SR5-2, R32: Each resistor should measure 4.7K ohms Address decoder U16, pin 10
] Check CPU-Board outputs
| CPU Board latch | Logic probe | *PULSING--replace the sound data cable |
| U39/U59, pins 12 | (Game on and | -ANY LOW--unplug 1P8 and retest |
| through 19 | in Test 4, | *PULSING NOW--bad Sound Board: per- |
“Play Synthe- form Sound Board checkbox above sizer" subtest) *STILL LOW--replace latch that has stuck bits (U39 or U59) *ALL PINS LOW OR HIGH--dead clock function (U39 or U59, pin 11 or U78, pin 12): replace bad latch U39 or US59, or PLD U78 Missing Sounds; No Sound--Step 2 (Assumption: Off-board Failure)
No Sound (Assumption: Power Section Failure) [ ] Check the power sources
- With the power on, use a VOM to check DC voltages at jack 10J3: +5V at pin 1; +12V at pins 5 and 6; -12V at pin 3; ground at pins 2, 7 and 8. Also +8V at transistor Q1's emitter. The +5V line may be open or ripply: Test for AC! No more than 0.005VAC is normal. Other power lines may be low (for example, overloaded by bad 100 uF capacitors). A shorted +5V line brings down the main system.
- If +5, +12 or -12V are absent or low, turn off game. Check associated cables and electrolytic capacitors. Start with 100 uF capacitors C2, C6 and C16.
- If +8 is absent or low, check regulator ZR3/Q1/C15, etc.
TROUBLESHOOTING YOUR SOUND BOARD
SYMPTOM TEST AND PROCEDURES
Still No Sound {] Check the Audio (Analog) Section (Assumption: (1) Turn the power on. Turn up the volume control. Audio Section (2) Rub your fingertips over the preamplifier pins (U19, 21 and U39). U19 is the Failure) synthesizer preamp. U39 is the preamp for the CVSD. U21 is the DAC preamp. Check each chip separately.
- A low hum indicates that the audio amplifiers, volume pot and speaker are okay. A problem may still exist in the attenuator stages before the preamps. (If desired, use this technique to increase the volume of the hum: While rubbing the analog inputs, lay a finger on the pins of nearby digital chips.) MISSING OR DISTORTED SOUNDS--check Power Supply voltages at the analog chips (see Power Sources checkbox above) MISSING SOUNDS FROM ONE SOURCE--Check the appropriate preamplifier and both power amplifier chips. Preamps: For missing music (synth)--U19; missing sound effects (DAC)--U21; missing voices (CVSD)--U39. Power amps: U32 and U41. All chips OK? Check electrolytic capacitors C20, C34, C48, C55, C67, C68. Missing Sounds; }[ ] Check the Sound ROM Section and related circuitry No Sound (4) Turn the power on. (Assumption: (2) What if you have no sound but power supply voitages are nominal (ripple-free Digital Failure) +5VDC)? Then check the cleck oscillator. Using a VOM or logic probe, test for pulsing AC across crystal CRi. Also test for pulsing DC across flip-flop U11. If the clock signal's absent, replace oscillator CR1.
- Turn the power off.
- As a test, try replacing the ROM chips we specify below: Replacements should be made one at a time. Don't discard the original chips! «if MUSIC is missing or absent, replace Sound ROMs U3 through U5. Still missing? Swap RAMs U2 and U34. If music now works, but sound doesn't, replace bad RAM at U34. If SOUNDS (other than music) are missing or absent, replace Sound ROMs U3 through U6. Only substitute known-good chips. After each replacement, perform step 5. Still missing? Swap RAMs U2 and U34. It sound now works, but music doesn't, replace bad RAM at U2.
- Power-up and test the Sound Board after each swap. Use Diagnostic Test 4.
- As a test, replace first microprocessor U1 and then U33 with known-good chips. After each replacement, perform step 7.
- Power-up and test the Sound Board after each swap. Use Diagnostic Test 4.
Chapter 3. Unique Paris
Electrical Parts Semiconductors
Hardware
Major Assemblies and Subassemblies
Programmed Chip Summary--Part 2
Warnings and Notices
Unique Parts CATEGORY DESCRIPTION PART NUMBER Electrical Batter Lithium Battery, 3V 5880-11056-00 Parts 20-Pin, 6" Ribbon Cable 5795-10937-06 Cables H-1210
Power Supply Cord Assy Speaker Cable
S
Seis me
Electrolytic Capacitors
jar ee
: fie goin 2.2 uF at 50V +/- 20% 5040-12294-00 1 uF at 50V +/- 20% 5040-12293-00 \%o oe ae Fluorescent Lamp Parts
Starter (replacement) 20-8748-1 §551-09822-00 5610-12
CATEGORY TYPE -DESCRIPTION PART NUMBER Electrical Pots and ADVANCE-SPST Switch 5643-09268-00 Switches DPDT, 100V, 5A 5641-09312-00 | OPST, 227V, 15A On/Off 5640-10932-00
: ae Pot, 10K, 1W. 5014-12363-00 Single Inline | 4.7K Ohms x 5 5019-09786-00 Pkgs (SIPs) | 4.7K Ohms x9 5019-09362-00 u
.e
Semiconductors|Analog ICs udio Power Amp 3303 Op Amp (Preamp) 3340 Active Attenuator Oscillators MH
RAM ICs O64 of : 4461 DRAM (64K x 4 5340-12213-00 4464 DRAM (64K x 4) 5340-12014-00 5564PL 8K x 8 CMOS SRAM
Random Logic
LS138 3/8 Line Decoder 5281-09745-00 74LS139 2/4 Line Decoder 5281-09246-00 [Ant S245 ranso ld - 00
TIP122 NPN Darlington 5162-09410-00 Varistors and] Varistor, 130V, 10J 5017-09044-00 *f e. Octal Flip-Flop 5317-12212-00
Tee
CATEGORY TYPE DESCRIPTION PART NUMBER Semiconductors, | VLSI Chips [Custom DMA (ASIC) 5410-12239-00 continued TMS34010 GSP 5400-12220-00 I68BO9E_ Microprocessor 5400-10
Misc. Electronic Parts 55536 7224 D/A Converter IC Hardware Metal and i Wooden Misc. Parts
Door Lock Retainer
Door, Lower Rear Door, Monitor Box (Rear L Up
= C-12140-1 C-12140
Toggle Latch Trunk Latch Bracket
Volume Pot Bracke 01-6858
CATEGORY TYPE DESCRIPTION PART NUMBER Hardware, Rubber, Control Panel Cover 31-1450-3036-U1
continued Glass and | CRT Bezel (24.5" High) 03-8180 Plastic M /CRT Gl Parts
Neopr_Gasket,3/4x26-3/4 23-6 5
Major General Control Panel Assembly D-12202
Assemblies and Subassemblies
Lwr Rear Door Assy (w/Bds Main Harness Assembly
ROM Bd Subassy (no ROMs) C-12261 Sound PCB Assembly C-12350 Sound Bd Subassy (no ROMs’ C-12349 up b
Notes...
Notes...
Notes...
Programmed Chip Summary (Continued from Inside-Front Cover)
Image ROM Image ROM Image ROM
Image ROM Image ROM Image ROM
Image ROM Image ROM Image ROM
ee Image ROM Image ROM Image ROM reer: 1
i Image ROM Image ROM Image ROM e ie
G Image ROM Image ROM _Image ROM 27512 | ROM Board U61 27512 | ROM Board U62 27512 | ROM Board BO 27512 | ROM Board U55 A-5343-3036-43 ROM 27512 | ROM Board U56 A-5343-3036-44 27512 | ROM Board U57 oy =
| is | 27512 | [ROM Board U73 | | |
ROM 27512 | ROM Board U74
| ROM | 27512 | ROM B | ‘d U75 |
S B ee
| Oo | 27512 | RO | ard U79 |
FROM 27512 | ROM Board U80 FROM 27512 | ROM Board U81 a ar & CH ty cd cM al O joard U85
FOM ROM Board U86
27512 | ROM Board U87 ae
Warnings and Notices
USE OF NON-WILLIAMS PARTS or circuit modifications may cause injuries or equipment damage.
SUBSTITUTE PARTS OR MODIFICATIONS. may void FCC Type Acceptance.
THIS GAME IS PROTECTED by Federal copyright, trademark and patent laws. Unauthorized software or hardware modifications may be illegal under Federal law.
THIS "MODIFICATION" PRINCIPLE ALSO APPLIES to unauthorized facsimiles of WILLIAMS logos, designs, publications and assemblies. Moreover, facsimiles of WILLIAMS equipment (or any feature thereof) may be illegal under Federal law. Whether or not such facsimiles are manufactured with WILLIAMS components, this rule applies.
RF-INTERFERENCE NOTICE YOUR GAME'S CABLE-HARNESS PLACEMENT and ground-strap routing are very
MAINTAIN THESE LEVELS. Servicing may require that you disconnect harnesses or ground straps. When you're finished, reposition and reconnect them as they were.
NOTICE NARC, Z-UNIT and WILLIAMS are trademarks of WILLIAMS ELECTRONICS GAMES, INC. Entire contents of this manual copyright (C) 1989 WILLIAMS ELECTRONICS GAMES, INC. All rights reserved
NOTICE For service, call your authorized WiLLIAMS Distributor