CATHODE RAY TOMES

Rip Off

Rip Off (Cinematronics, 1980) · Manual · 84 pages · 45 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

CINEMATRONICS, INC.

1466 Pioneer Way

El Cajon, California, 92020

TELEX: CINEMAT 697891

CALL TOLL FREE: 800 854-6577

IN CALIFORNIA CALL: 714-440-2933

SALES: 8-5 (PST) WEEKDAYS

SERVICE: 7-5 (PST) WEEKDAYS

Page 3

OPERATION AND MAINTENANCE

MANUAL

CINEMATRONICS, INC. 1466 PIONEER WAY EL CAJON, CA. 92020

Copyright 1980 All Rights Reserved

Page 4

CUSTOMER SERVICE PROCEDURES

It is the desire of Cinematronics, Inc. to provide efficient and courteous service should the need arise. We have a fully staffed Customer Service Department and encourage you to call our toll free number: 800-854-6577,78, for technical assistance between the hours of 7:00 A.M. and 5:00 P.M., California time, Monday through Friday.

In order to provide the very best service possible, the following procedures for ordering or returning parts must be followed:

  • All equipment ordered from Customer Service, whether in or out of Warranty, must be placed with a Distributor’s purchase order, either by mail or verbally by telephone.
  • Advance replacement items may be obtained only during the term of the Warranty and when such items are available, using the same procedure as when ordering parts. When ordering a PCB, please include with your order the game serial number and the number of the PCB you wish replaced.
  • Allitems received as advance replacements will, after a period of thirty (30) days, become the property of the Distributor, with applicable charges applied in the event Customer Service has not received the defective item against which the advance replacement was made.
  • The Distributor must call this facility for an RMA number prior to returning any item. Please be prepared to provide us with the game serial number and the PCB number when requesting an RMA.
  • Inall situations covered above, and in all other situations, the Warranty offered by Cinematronics, Inc. is appicable and should be fully understood.
  • Parts returned for service must be packaged so that no damage is incurred during the shipment. Cartons without a prominently displayed RMA number will not be accepted. Full documentation including game serial number, PCB number and reason for return must accompany parts. Ship prepaid to:

Cinematronics, Inc. Customer Service Department 1466 Pioneer Way El Cajon, CA 92020

800-854-6577 714-440-2933

Page 5

WARRANTY

Cinematronics, Inc. warrants the goods to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of delivery on all parts except switches, buttons, lights and fuses, for which the warranty period is thirty (30) days from the date of delivery. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein. Cinematronics limits its warranty obligations herein to the repair or replacement of such parts which have been returned to Cinematronics’ plant at purchaser’s expense and which examination shall disclose to Cinematronics’ satisfaction to have been so defective and to the shipment of such repaired or replacement parts to the purchaser F.O.B. the shipping point.

This warranty does not apply to any Cinematronics product which has been altered or repaired by unauthorized personnel or service facilities or any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liability for damages and/or bodily injury by the purchaser or any other person and to hold Cinematronics, Inc. harmless from liability or claims arising from the use of the goods by any person. Purchaser further agrees to indemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.

Parts returned for warranty service must be packaged so that no damage is incurred during the shipment. Full documentation and instructions must accompany returned parts. Parts must be shipped prepaid to:

Cinematronics, Inc. 1466 Pioneer Way El Cajon, Calif. 92020

Page 6

TABLE OF CONTENTS

Section Title Page 1 INTRODUCTION ......0 0-0-0020. 0 eee eee e ees beeen eens 1-1 2 INSTALLATION ... «02.2.0 20-00-02 e eee eee nr iabb hi meget ses . 2-1 3 GENERAL INFORMATION ...........-.----> bebe cence eee 3-1 4 VECTOR THEORY ..........-...-000 esse eee oye? gs eee pe cee 41 5 THEORY OF OPERATION ........--..-055-5> beeen eee e eens 5-1 A. MONITOR B. CPU C. AUDIO 6 MAINTENANCE .........--005-000 0025 eres veces cece ee 6-1 A. UNIVERSAL BENCH TEST B. TROUBLE SHOOTING FLOW CHART C. TROUBLE SHOOTING GUIDE 7 PARTSLISTS .......... poset amee dee taune ee ands eek wa Eee eee 71

APPENDIX A Assembly Drawings. Schematics & Wiring Diagrams...........2-0eseeeeeee ee 8-1

LIST OF ILLUSTRATIONS Figure Title Page

4-1 Graphical Representation of a Matrix .. ©... 6656s 4-2 4-3 Line using Vector System ... bec e tenes 4-2 4-2 Non-linear Charging Voltages ......-....-.-0- 5-050 0 4-3 5-1 CPU-Functional Block Diagram .........6-. 000000 c eee ete ene ee 5-6 5-2 Detailed Block Diagram ...... 2.0.6.0 0c cece eens 5-7

LIST OF TABLES

Table Title Page 2-1 Operation Option Switch Positions ........--... 0.00.2. s sere tees teeenes 2-2 5-1 CPU-Block Numbers and Component ILC. 0.2.2... 0.0500 e cee 5-8 6-1 Troubleshooting Guide ..........2- 00005 e eect e eee eens wees 6-1

Page 7

SECTION 1

INTRODUCTION

Page 8

INTRODUCTION

RIP OFF is a one or two player action game that offers features guaranteed to capture and prolong player interest: an accelerating competitive level with a clearly visible object and a team competition option that allows players to combine scores as well as skills in defense strategy against a futuristic enemy.

The center of the playfield is occupied by a selectable number of triangular fuel cells that pulsate with radioactive energy. The player commandeers a land craft that turns left, right, accelerates and fires torpedo energy bursts activated by push-buttons mounted on the “bridge” control panel. All is quiet as the background audio repeats an ominous low frequency tone. Suddenly, alien craft enter in waves from the edges of the playfield attempting to attach their vehicles to the fuel cells and drag them off to restock their own dwindling supplies. The player maneuvers his land ship into position and fires a volley of torpedoes at the first invader, causing his vehicle to explode in a thunderous roar and a flash of light. A second invader retaliates by firing short range laser bursts at the defender ship while a third invader escapes, dragging off a precious fuel cell. The background audio quickens its pitch and tempo as another wave of sleeker, faster invaders attack and maneuver to rip off fuel canisters — and the battle rages on!

GAME PLAY

There are three modes of play in RIP OFF: a) the attract mode; b) the one player mode; and c) the two player mode.

The attract mode is activated when power is applied. In the attract mode, triangular figures appear in the center of the screen. “Enemy” vehicles then appear in groups of three from various points on the edge of the screen and gravitate toward the triangles in the center. Upon reaching the triangle, the “enemy” vehicle comes to a full stop with its nose pointed directly at the triangle. The vehicle then makes a 180 degree rotation, attaches itself to the triangle, and drags the triangle off the screen toward a randomly selected point. When all the triangles have left the screen, the attract mode begins its cycle again.

The one player mode is activated when a coin is accepted and the player pushes the one player button. As play begins the first player’s vehicle appears on the right side of the screen and moves slightly forward. The enemy vehicles then appear in pairs from various points on the edge of the screen and gravitate toward the player and the triangles. The enemies fire lasers while they move. The player scores points by either shooting the enemy or colliding with him before the enemy can shoot the player, collide with him or drag his triangle off the screen. When a player’s vehicle is exploded, it reappears on the right side of the screen where it began. When a player has sufficient points to achieve a bonus level, the enemies will appear three at a time instead of in pairs and their point value increases. Each bonus level increases the enemies’ point value, as well as their ability to seek out and destroy the player. When all the ae aa have been dragged off the screen, the game is over and the unit reverts to attract mode.

The two player mode is activated when two coins have been acceted and a player pushes the two player button. As play begins, the first player’s vehicle appears on the right side of the screen and the second player’s vehicle appears on the left. Both vehicles move forward slightly. Enemy vehicles then appear in groups of three and attack the players and seek to drag off the triangles. Players score points by colliding with the enemy vehicles or shooting them. No points are scored by shooting or colliding with the other player. Should the players’

1-1

Page 9

ships collide, an explosion will occur and the players’ vehicles will reappear at the points where they began.

In the two player operator selectable opponent mode, individual scores are displayed after each wave of attackers are destroyed or successfully leave the screen. In the team mode, the combined score of both defenders is displayed. At the end of the game, when all fuel cannisters have been removed, the individual high score for the day is displayed at the bottom of the screen and the high team score is displayed at the top.

A player achieves bonus levels in which the value of each invader vehicle is increased by the displayed amount of the bonus. There are six different types of invader vehicles, each wave becoming increasingly offensive and more difficult to destroy. The point bonus is in effect after six waves, the full compliment of ship types, have been destroyed. There are three similar craft in a wave, and in the two player mode twelve waves must be eliminated before bonus goes into effect.

There are no time units per game credit, and the battle goes on until all fuel cannisters have been “ripped off” from the playfield. The length of play is solely dependent upon the skill of the player — but it takes an experienced, practiced captain to hold off the swift invaders for long!

Page 10

SECTION 2

INSTALLATION

Page 11

SECTION 2

INSTALLATION

RECEIVING INSPECTION Your game was shipped in ready-to-play condition. However, after removal of the shipping carton, a brief visual examination is suggested.

Naturally, you’ll want to make note of any physical damage to the game cabinet and its external components for freight claim purposes. Considering the quality of the shipping carton, any damage to the exterior would indicate possible interior damage as well.

The interior of the game should also undergo a brief examination for: loose mounting hardware (check to be sure that the major components are still securely mounted); disconnected or loose wires, cables or harnesses; electronic devices loose in their sockets; etc.

At this time the game serial number should be logged. Please remember that the game serial number will be required if you need service from your distributor.

ELECTRICAL REQUIREMENTS

Unless specified otherwise, your game was shipped to operate at 115 VAC, 50/60 Hz. Two other voltage settings are possible. The power supply chassis has a table which shows the voltage options and fusing requirements.

A good earth ground is essential for the

2-1 proper operation of this game or for that matter any electronic device. Problems with instability and erratic operation of computertype devices can usually be traced to an ineffective ground system.

INITIAL ADJUSTMENTS

NOTE

When the game is connected to AC power, one of the game sounds may be heard. This is normal.

The audio level (volume) can be easily adjusted and THIS IS ACHIEVED BY ROTA- TION OF THE VOLUME POT LOCATED ON THE COIN DOOR. The audio level should compete with other machines “on the floor” to maximize play time.

Display brightness is another easy adjustment. The monitor assembly has several adjustments, but the brightness control is the only one which does not require a “‘screwdriver’’ for rotation. Keep the brightness at the correct level for appeal.

OPERATOR OPTIONS

The option switch is located on the logic or game board. It is not necessary to remove the board from the cabinet to set the options. In fact, the option switch and audio control can be reached easily through the coin door. opening. Table 2-1 will assist you with your selections:

Page 12

LOGIC BOARD OPTION SELECT TABLE

The following chart diagrams the switch settings of the option switches for “RIP OFF”. The 7 station switch is located at position E-2 on the logic board (refer to logic board layout in appendix).

RIPOFF OPTION SWITCHES

ON = DIAGNOSTIC MODE

ON=OPTIONAL SCORE

ON = NO SOUND IN ATTRACT MODE

CREDIT &

CRECIT 1

TIME & TIME 4

CREDIT |

TABLE A TABLE 2-1

Switch Descriptions 7 — Generates a test pattern for alignment purposes. 6 — Displays individual scores for each player or one combined score. 5 — Allows motor audio in attract mode. 4,3 — Credit per coin selectors defined in Table A. 2,1 — Fuel cell selectors defined in Table B.

2-2

Page 13

SECTION 3

GENERAL INFORMATION

Page 14

SECTION 3

GENERAL INFORMATION

Your Cinematronics game is designed much the same as conventional video games. The major exception is the use of an alternate means of visual display ... the patented Vectorbeam tM” monitoring system.

However, the game is built of the same basic building blocks as any other video game:

The Power Supply provides all necessary voltages for each separate electronic assembly as well as the AC lighting required throughout the game.

The Central Processing Unit contains circuitry to strobe and interpret all input functions which include the player control panel switches and all coin and credit information and generates all the digital signals used to provide the visual display and control the audio effects. It also contains all the software (i.e., machine language and game personality memory) needed to control the game operation and to generate the proper vectors for the display.

The Audio Board consists of a noise generator and wave shaping circuits which produce different game sounds on command from the CPU logic board.

The Vectorbeam tM” Display Electronics is the final form of interpretation of the CPU’s calculations. The CPU logic informs the display electronics unit of information regarding line length and line placement on the CRT. This is accomplished withtwotwelve-bit words each for horizontal and vertical deflection, and a number of other controlling signals for the cathode drive circuit and switching of the deflection circuits.

3-1 The major difference between the vector generator and raster scan type monitors is the means by which the cathode beam is directed (deflection) across the screen.

In the raster scan type of display, the electron beam from the cathode to the anode of the CRT is constantly deflected (scanned) across the face of the CRT in a series of horizontal lines that trace from the upper portion of the screen to the bottom in a synchronous pattern. Vertical information is formed using a matrix-type pattern of mathematically possible illumination points on the face of the CRT. If the cathode current is increased at these points on the screen in matrix-type patterns (similar to placing dots on a piece of graph paper where the lines intersect) coherent video in the form of shapes and alpha-numerics to form game backgrounds can be displayed.

The vector generator takes a slightly different approach to cathode beam deflection. The results are a much higher degree of resolution and much smoother motion across the screen. Rather than using a constantly scanning cathode beam, the beam is directed only to points of eventual illumination, using a vectoring form of programming rather than a matrix approach. Basically, the cathode beam is directed between two determined points, and illuminates the entire path of phosphors between these two points, unless blanked by stopping cathode current (i.e., when the beam moves from one star to another on your screen). The ability to illuminate the entire path of phosphors crossed by the electron beam, in any direction desired, (which is not possible in a raster scan system) creates a

Page 15

much higher degree of resolution than can be found in a raster scan system while at the same time creating a much greater number of angle possibilities. This is also supported by the ability to accommodate two twelve-bit words of information, twelve each for vertical and horizontal deflection, and the fact that there is no background illumination from a constantly scanning beam when brightness is turned up. The higher degree of resolution

hd ,, + “Vectorbeam tM” is Cinematronic’s service mark for video game repair and education services.

3-2 combines with the totally blackened background generating an appearance of depth not found in a raster scan system.

Another major design difference is the fact that no sync. signals are needed to produce vectors on the CRT. This greatly simplifies the hardware design of the system, and therfore the understanding of the theory of operation, both the CPU logic and the display electronics.

Page 16

SECTION 4

VECTOR THEORY

Page 17

SECTION 4

VECTOR THEORY

In order to understand the basic concept behind a vector generated display, it is

important to have a basic knowledge of vector theory.

As mentioned in the general information section of this manual, the raster scan display uses a matrix type display pattern. A graphical representation of a matrix is shown in Figure 4-1.

For example, to produce a line on the CRT with a matrix-type pattern, the appropriate intersection points of horizontal and vertical lines are illuminated. The calculations which select these points are made on the logic board, and converted into video information for the monitor to digest. Although there are spaces between the illuminated points, the illusion of a solid line is made by your eyes, and the resolution is determined by the number of available horizontal and vertical lines in the system, and the speed of the sweep.

In the vector display system, there are no horizontal and vertical lines (no sweep) or sync. A line generated using a vector system is shown in Figure 4-2.

A line is drawn by programming a beginning and ending point of the line to be drawn, and forcing the cathode beam to travel between these two points, illuminating the entire path of phosphorus on the CRT. The angle of the line. the position of the line, and the length of the line are determined simultaneously, and simply, by selecting the proper voltage levels for the beginning and ending points of the line.

This is accomplished by the two twelve-bit codes (words) applied to the DAC-80s on the display board. The DAC-80 will produce a different voltage level at its output for each possible combination of input levels (of which there are 4096 possiblities for each 12 bit word.)

It is also important to remember the function of the LF 13331 analog switch and its output RC network. Because we are dealing with reactive components in C101 and C201 on the display board the charging voltages found are non-linear by nature. (See figure 4-3.)

Therefore, when a line appears on the CRT, it is actually only part of the entire path taken between the beginning and ending points of the vector (C-D). The section of A-B is chosen as the most linear portion of the charge curve, and is iliuminated.

Sections C-A and B-D are blanked at the cathode, and points A and B chosen by controlling the analog switch on the display board. These calculations are all performed on the CPU logic board.

Page 18

HORIZONTAL

VERTICAL

Figure 4-1. Graphical Representation of a Matrix

BEEP ae PT yy er tT PT TA fendredne|vofeage bustve | | Vela | [otleatacteok [ | | | | Tyr TTT TPT Tee PT TT TTT Tt tT

‘A BCR SERREEEC CURR

Figure 4-3. Non-linear Charging Voltages

4-2

Page 19

PLT TTT TT Te TT tT tt Tr PITT TT TTT ty Pr rr

Figure 4-2. Line using Vector System

When a line appears on the CRT, it is actually only part (section A-B,) of the entire path taken between the beginning and ending points of the vector (section C-D). Section A-B is chosen as the most linear portion of the charge curve, and illuminated.

Sections C-A and B-D are blanked at the cathode, and points A and B chosen by controlling the analog switch (V-1) on the display board. Again, these calculations are all performed on the CPU logic board.

4-3

Page 20

SECTION 5

THEORY OF OPERATION

Page 21

SECTION 5

THEORY OF OPERATION

GENERAL DESCRIPTION

This section describes the principles of operation of the major circuit functions of the Cinematronics Video Arcade Game. The system’s general functional description is followed by detailed circuit schematics which are included as Appendix A. The schematics used in this manual are similar in nature to those used by most industrial electronic firms.

MONITOR DISPLAY The Vectorbeam t™ monitor is unlike the conventional TV monitor in that it displays vectors (lines) generated from X-Y coordinates recieved from the logic board. The horizontal points are X (width) and the vertical points are Y (height). The X and Y logic signals originate from the logic board.

The Vectorbeam *™ monitor can be divided into two basic sections: one is the deflection amplifier and the other is the voltage and cathode drive circuits.

The deflection amplifier can be further divided into two identical channels: one for the vertical deflection and one for the horizontal deflection. The operation of the vertical channel will be discussed; however, the same theory of operation pertains to the horizontal channel.

Digital information, in the form of a twelve-bit word, is applied to the input of the DAC-80 digital to analog converter (U101) on pins one through twelve. The most significant bit is applied to pin one, and the least significant bit is applied to pin twelve. The DAC-80 makes the necessary conversion from digital signals to analog signals which are outputted as analog voltage signals on pin fifteen (proportional in level depending on the input word applied). The result is a positive and negative voltage signal about its reference

5-1 voltage. Remember, there is no ‘‘sync’’ signal present, and the signal is not true video as seen in raster scan monitors.

From the DAC-80 the analog signal is then sent to a high-speed analog switch, (U1). The analog switch has two parallel inputs for the display signal, and two controlling inputs which select one of two outputs from the switch. An R.C. network, which is used to create line length and line position on the screen is found at the outputs.

Output fifteen from the switch routes the analog signal through a 5K potentiometer (R102), a 10K resistor, (R103) and to the input of U102 op-amp. The time constant developed by these two resistors and the capacitor (C101) determine the length of the vector line seen on the screen. Adjusting the potentiometer will adjust the length of the vertical lines seen on the screen.

Output ten from the analog switch routes the signal directly to the input of U102 op-amp, and the resulting time constant of the op-amp input impendence and the capacitor C101 determines the position on the screen of the vector line.

Op-amp, U102, serves a dual purpose: it acts as a buffer between the deflection amplifiers and the analog switch, as well as an ‘‘edge gain”’ amplifier (i.e., height).

At the output of U102, there is a resistor diode network consisting of R105-R110, and CR101-CR104. This resistor diode network is used to compensate for the non-linear characteristics of the CRT near the edges of the screen. If this circuit were not used, any object displayed on the screen would increase in size as it moved closer to the edges of the screen. Potentiometer (R109), adjusts the height of the pictures.

Page 22

From the wiper of R109, the signal proceeds to Q101, which is the first stage of deflection amplification. Q103 is emitter coupled with Q101 to provide a degenerative feedback loop from the yoke. Q102 is used to provide a constant current source to both emitters.

At this point, the deflection circuit can again be divided into two identical circuits. One circuit, which controls the lower half of the screen, is comprised of Q104, Q106, Q108, and Q110. The other circuit, which controls the upper half of the screen is comprised of Q105, Q107, Q109, and Q111. **

Q104, Q108 and Q110 are three stages of amplification, while Q106 is used as current limiting protection for Q108 and Q110. The same holds true for the other configuration of Q105, Q107, Q109 and Q111. R124 through R129 are used as a current divider network for the yoke.

R122, R123, and C102 form a RC network, which compensates for any counter EMF that may develop by the expanding and collapsing of the deflection coil’s electromagnetic field.

The high voltage and cathode circuitry is the second section of the monitor. This section also contains the necessary voltage regulation to power the ICs located on the display board as well as develop the high voltage.

U4 and U6 provide plus 15V and minus 15V respectively to power the DAC-80s and the TLO81 op-amps on the display board.

U3 and U5 provide plus 18V and minus 18V used in the high voltage transformer (T-1) and oscillator (the oscillator circuit is necessary because there is no horizontal sync. used to develop the high voltage pulses.) The oscillator circuit is comprised of primary windings, Q4 and associated discreet components.

5-2 The high voltage 18KV is developed by Tl secondary windings, and the high voltage tripler.

The intensity and beam blanking control circuitry is composed of U7, Ql, Q2, Q3, Q8 and associated components. The cathode voltage rides at +88. The beam is turned on by a more negative voltage. At the anode of CR4 negative pulses can be seen, these are the beam on pulses. For normal intensity the pulses will go down to approximately 40V, for double intensity, 20V. Pins 3 and 4 of U7 is the normal intensity control gate which receives information from the CPU. Pin 1 and 2 is the double intensity control gate. When a Hi going Lo signal is on pin 3 of U7 pin 4 will be a Lo going Hi turning on Q3 on the Hi transition. Q3 acts as a switch connecting the series network of R11, R9 and R10 to ground creating a voltage divider network. R11 is the manual intensity control. When 2 of U7 goes Hi Ql turns on for the duration of the pulse connecting just R9 and R11 to ground, thus lowering the voltage at the anode of CR4 lower still because of the lower resistance, than with normal intensity. Q2 is used as a switch to enable Q1 and Q3. Its purpose is to shut off the beam when the power is turned off. Q8is a beam on delay to prevent phosphor burns if someone was to unplug and plug in the machine rapidly.

R111 is the brightness potentiometer, which adjusts the amplitude of the negative spikes used for brightness and intensification.

** In the horizontal section of the deflection amplifier, Q204, Q206, Q208 and Q210 control the left hand side of the screen, and Q205, Q207, Q209, and Q211 control the right hand side of the screen. By dividing the screen in this manner, four quadrants of deflection area have been developed (refer to Vector Generator description).

Page 23

CPU BOARD

The processor hardware can be broken down into five basic functional blocks as shown in Figure 5-1. The arrows indicate the possible data flow directions between the various blocks. The ALU and Control block are the main components of the processor while the Memory and I/O blocks may be thought of as merely peripherals. Figure 5-2 is a detailed block diagram of the processor. The numbers in each block correspond to the entries in Table 5-1, which lists the IC numbers of the main components of each functional block. The following is a brief description of each block shown in Figure 5-1. The numbers beside each functional block name are the numbers in Figure 5-2 which correspond to a particular function.

RAM (6)

The RAM is implemented with three read/write static memories configured as a 256 x 12 bit block. Datacan be transferred to or from this memory via the ALU block. The processor uses this RAM as a scratch pad.

ROM (10)

The ROM is configured as an 8K x 8 bit block of memory. These memory locations contain the program instructions and/or data. It is accessed via the processor control unit.

1/0 19, 17, 18

The I/O block consists of 8 output lines implemented with a bit addressable latch, 24 input lines implemented with data selectors, and two 12 bit registors which are connected to the X Y display deflection circuits via D/A convertors.

Arithmetic Unit 1,2,3,4,5

The arithmetic unit performs all the arithmetic processing for the system. It consists primarily of two 12 bit accumulators, an arithmetic logic unit and various data selectors. The accumulators can function as temporary storage registers for arithmetic

5-3 functions upon the data in the accumulators. The data selectors are used to select the various sources of data which will be processed.

Control Unit (15,16,14,7,8,9,11,12,13)

The control unit is the heart of the processor. It performs all instruction decoding operations and generates all the necessary control signals which the rest of the hardware requires to function correctly.

The following is a discussion of each block shown in Figure 5-2.

  • Accumulator Selector

The accumulator selector consists of 3 quad data selectors. They are used to select the output of either the primary or secondary accumulator for processing by various other sections of the systems.

2 & 3 Primary and Secondary Accumulators

The two 12 bit accumulators are implemented with quad bidirectional shift registers. The primary accumulator consists of S4, P4, M4. The secondary accumulator consists of T4, R4, N4. All data manipulation in the processor is accomplished using these two accumulators. All output data flows through these registers.

  • Arithmetic Logic Unit (ALU)

The ALU is used to perform all necessary arithmetic functions within the processor. The ALU is implemented using three 24LS181 (N6M6L6) function generators, three 74LS85 (N9,M9,L9) 4 bit magnitude comparators, and a74S182 (L4) look ahead carry generator. The data which the ALU manipulates can come from four different sources. The first source is the contents of the accumulators via the accumulator selector. The second and third sources are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11) and the fourth source is the external input selector (E4, D4, C4).

Page 24
  • Data Selector

The data selector is used to read data into the ALU from either the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the RAM data is 12 bits wide.

  • RAM Storage

The system RAM consists of three 9101C high speed static memory chips connected as a 256 x 12 bit block. The block is 12 bits wide in order to allow the contents of an accumulator to be stored. The processor uses the RAM as temporary storage of program variables, data pointers or any.other data of a dynamic nature.

  • RAM Address Selector/Register

The output of this register is tied directly to the address lines of the RAM. It consists of a multiplexer which routes address data from either the ROM or RAM locations to the RAM address lines. The capability to use RAM data to select RAM addresses is the basis for the indirect addressing mode of the processor.

  • Page Selector

The page selector is used to latch the high order 4 bits of a RAM access instructions.

  • ROM Data Register

The register is used to temporarily hold data from the ROM during an instruction fetch.

  • ROM Memory

The ROM memory consists of the actual memory chips plus a data selector and latch circuit. The latch is used to improve the memory access time during a two byte instruction fetch by allowing one byte of the instruction to be latched while the RAM address lines are decoded for the other byte. The data selector can then be used to rapidly access both bytes of the instruction by switching between the latch and memory outputs.

11._ Instruction Register

The instruction register is a latch which holds the current op code as read from ROM. Its output is tied to the instruction decode circuitry which in turn generates the necessary signals to execute the instruction.

12, System Sequencer

The system sequencer is used to decode an instruction op code and to generate the appropriate timed sequence of signals which execute the instruction. The op code is decoded by using it as the address data to a set of decoder ROMS. The outputs of the decoder ROMS are then synchronized with the system clock and used to control the various system functional blocks.

  • Line Length Counter

The line length counter is used during the process of drawing a vector to control the length of a vector, by turning off the beam at a pre-determined time after the vector is intiated. The counter is loaded with a value from a line length ROM and then counts up until it overflows which in turn generates a signal to indicate the vector has been finished.

Page 25
  • Program Address Selector This selector is used to provide the address data to the program ROM. It selects either the program address counter output or the accumulator selector output and routes this data to the ROM address lines. The ability to use the accumulator contents as address data allows the program to randomly access data tables stored in the ROM or to compute a branch address after a conditional test.
  • Program Address Counter

This is a 12 bit counter whose output defines the next location in ROM to be accessed. It is normally clocked sequentially to step through a program. However, it can be loaded with data from the program address register which is how the jump instructions are implemented.

  • Program Address-Register

This register is a latch used for temporary storage of an address which will be loaded into the program counter during a jump instruction. The input data to this latch can come from either the program ROM or the scratch-pad RAM.

17._Input Selector

The input selector is used to read the state of one of the 24 input lines into the selected accumulator. There are 16 primary inputs and 8 secondary inputs. During an input instruction the upper 11 bits of the accumulator are set to zero while the least significant bit reflects the state of the input line. All input lines have pull up resistors on them so that they will read high if they are left unconnected.

  • Output Selector

The output selector is a bit addressable latch used to control the 8 output lines. During an output instruction the selected output line is set to the complement of the least significant bit of the accumulator. The output lines are used to control the audio board, display intensity and the mechanical coin counter.

  • Display Registers

The display registers are the interface between the processor and the display driver circuits. These registers are latches into which the contents of the accumulators can be stored. The outputs are tied to D/A converters which provide the input voltage to the display deflection amplifiers.

Page 26

CONTROL UNIT

Figure 5-1. Functional Block Diagram

5-6

Page 27

5-7 ‘ACCUM.

SELECTOR

DISPLAY

REGISTER To

© ADDRESS ‘ADDRESS LINE

COUNTER SELECTOR COUNTER

©) 2) @

MARY SECONDARY

ACCUM ADDRESS REGISTER

PRL SYSTEM SEQUENCER

ARITHMETIC UNIT o) 2)

INPUT

OUTPUT

©

DATA

INSTRUCTION REGISTER a)

@ ROM MEMORY

RAM TORAGE PAGE

ROM DATA REGISTER

RAM ADDRESS SELECTOR & REGISTER (0) © @ (©)

Figure 5-2. Detailed Block Diagram

Page 28

Fe N

10.

il.

12.

13.

14.

15.

16.

17.

18.

19. TABLE 5-1. BLOCK NUMBERS AND COMPONENT I.C.

T-2, R-2, N-2

S-4, P-4, M-4

T-4, R-4, N-4

N-6, M-6, L-6, N-9, M-9, L-9

N-11, M-11, L-11

N-14, M-14, L-14

J-12, 112

HAZ |

$-13

U-7, R-7, T-7, P-7, U-9, T-9, U-11, T-11

T:13

A-8, G-10, F-10, G-14, F-14, E-14, D-14, C-14

E-6, D-6, E-8, H-8, G-8, F-8

$-9, R-9, P-9

$-11, R-11, P-11

P-13, R-13

E-4, D-4, C-4

F-2

S-2, R-2, M-2

5-8

Page 29

AUDIO BOARD

GENERAL INFORMATION

The following section describes the operation theory of the game audio board. The appendix contains block diagrams of the audio section and includes the various curcuit elements that generate each particular sound. Each block will be described in theory along with test techniques following to enable effective troubleshooting of each sound.

The appendix of this section also contains some basic hints on testing and troubleshooting and should be read prior to isolating a problem on the board.

An asterick (*) in the left hand margin of a section indicates a detailed discussion of a circuit that will be used, but not discussed, in latter parts of the section.

*INPUT CONTROL CIRCUITRY (block 1)

1C25 is a Schmitt-Trigger inverter package that “cleans up” digital information arriving at connector J4 on pins 11, 12, & 13 (J4-11, 12, & 13). The CPU board controls all sound gereration by supplying digital data pulses through 16 pin connector J4. IC8 and IC9 latch this control information on the board as follows:

IC8 (74LS164) is an 8-bit serial-to-parallel shift register of which only 6 output bits are used (A-F). Data in the form of a bit stream marches from connector J4-11 through IC25 and into pin 2 of IC8. Pin 8 receives clock pulses from the CPU via J4-12. Each pulse causes a single bit of data present at pin 2 to be transferred successively down the line to outputs A thru F.

When the six output ports are filled, IC9 (74LS377) swings into action. the output of IC8 is tied to the inputs of IC9 (1D-6D). When IC9 receives a load pulse on pin 11 thru connector J4-13, the data present on each of its inputs is transferred straight across to its output ports (1Q-6Q). Now data which entered on one channel thru connector J4-11 is available for use in the 6 channels of latch IC9.

*TEST PROCEDURE — input control circuitry To verify proper operation of IC25, disconnect 16 pin ribbon connector J4 and decrease volume. Probe IC25-8 with logic probe, scope, or volt meter. It should read “high” or 2.4-5 volts DC (logic 1). Repeat for pins 10 & 12 of IC25.

With a test lead, ground IC25-5. the output of 1C25-8 should now read “low” or 0-+.7 volts DC (logic 0). Repeat for pins 10 & 12 while grounding 3 and 1.

To verify proper operation of IC8, load all “lows” into its output ports by tying IC8-2 to ground. With another test lead tap IC8-8 about adozen times. Outputs A-F should now all read low. At this point, tap IC9-11 with the ground lead. Outputs 1Q-6Q of IC9 should now all read low.

Repeat the above procedure, but remove the ground lead from IC8-2. This should load “highs” into all output ports and completes the test.

DIGITAL TO ANALOG CONVERTER (DAC) (block 2)

Output ports 1Q, 2Q & 3Q of IC9 drive digital to analog conversion circuitry consisting of IC10, IC19, D1 and various resistors (refer to Blk. 2). The circuit converts the various combinations of highs and lows on IC9-2, 5, & 6 into an analog voltage level at the output of IC 19. This voltage then drives circuitry to produce a background sound of increasing frequency as the level of IC 19-6 decreases.

TEST PROCEDURE — digital to analog converter

To test the DAC circuitry we will simulate the CPU by inputing various digital codes into pins 1, 3, & 5 of IC10 (7406). This chip is used as a simple switch as illustrated in the figure below: 7406 Switch low=0=ground —— high=1=+5 volts

“high”

Fig. 1

Page 30

When a logic 0 or low is placed on the input, the 7406 “switch” is open and sinks no current. Placing a high closes the switch and connects the output pin to ground.

D1 (1N5240) is a Zener diode & should always read +10 volts on the cathode.

Load all highs into IC9 as described in the previous section. This puts the digital code 111 on the inputs of IC10-1, 3, & 5. With a test lead, ground successively pins 1, 3, & 5 to produce the codes indicated in the table below. These codes generate voltages on the output of summing amp IC19 as listed:

IC10 — 1C19-6 Approx. 0 volts -2.5volts + 20% ~-1.3 volts + 20% -0.7 volts + 20% table 1 rOr rw Ovena

As each input of IC10 is tied low, its output should vary from 0 volts to approximtely 5 volts. If not, IC10 is defective. IC19 is a summing amplifier that converts currents from the resistor network R25-R30 into output voltages on pin 6. Should IC19 fail the test, lift diodes D6 & D8 out of circuit & repeat the procedure. Replace IC19.

BACKGROUND SOUND (block 2)

The background sound circuit is comprised of 3 main elements: a voltage controlled oscillator (VCO), mixer & level translator, and a gated octave adder (refer to Blk. 2). These elements produce a repeating tone burst of accelerating pitch & frequency.

*VCO

There are two identical voltage controlled oscillators consisting of IC20, IC21 and assorted elements (refer Block 2). The sole difference is the idling frequency and the IC21 circuit is discussed:

The output of IC21 on pin 6 is a rectangular wave pulse train swinging between +10 volts & -10 volts. With the output of the DAC circuit 1C19-6 at 0 volts, the variation on pin 3 of IC21 is limited to the voltage drop across D9 (+0.7 . volts) during the positive swing and the drop

5-10 across D8 (-0.7 volts) during the negative swing. At the positive swing, IC21-6is saturated at+10 volts. Current now begins to flow thru R80 (43K ) and attempts to charge C31 (.1mf) to this +10 volt level. Pin 3 is limited to +0.7 volts by diode D9, and as the charge of C31 passes this level, the output of IC21 flops to -10 volts.

Now diode D8 comes into play. With -10 volts at IC21-6, D8 forward biases and limits the level at 1C21-3 to -0.7 volts. Capacitor C31, which had just charged to alittle over +0.7 volts, sees the -10 volt level at IC21-6 thru R80 and begins to discharge toward -10 volts. As it passes through -0.7 volts, IC21-6 flops back to +10 volts, and the process repeats itself. The output of IC21 oscillates between +10 volts and -10 volts at a frequency determined by the time required for C31 to charge & discharge between +0.7 volts and -0.7 volts, the voltage limits imposed on IC21 pin 3.

If voltage excursion limits on IC21-3 were instead +0.7 volts to -2.5 volts. It would require a longer period of time for C31 to charge & discharge through this range. Since the output of IC21 does not flop until a limit is reached, this longer charging period implies a lower frequency of oscillation for IC21. Thus the name voltage controlled oscillator: by varying the lower limit voltage from -0.7 volts to -2.5 volts, the frequency of oscillation varies from a fast to a slower rate.

The lower limit is determined by the voltage at the anode of D8. The output of the DAC circuit is connected to the VCO at this point. The CPU can therefore vary the frequency of IC21 by providing various digital codes to IC10 pins 1,3, & 5.

TEST PROCEDURE

The output of IC21-6 will measure approximately 14 volts AC on a voltmeter. A completely dead VCO usually indicates a defective OP amp (IC21 or IC20). The VCO circuit will operate, but not correctly, with defective diodes D8 or D9. Verify with the OHM meter out of circuit.

Load all highs into the input control circuitry. Perform the test in Table 1 and observe

Page 31

IC21-6 on an oscilloscope. Frequency should decrease.

*MIXER & LEVEL TRANSLATOR

Transistor Q10 and its associated resistors (refer block 2) form the mixer and bipolar to TTL level translator. The two oscillators consisting of IC20 and IC21 generate voltage swings between +10 volts and -10 volts that are too large to be fed directly into IC22. It is also necessary to mix these large voltage swings of different frequency into a composite signal and then translate this composite level into a TTL compatible range (see appendix). Resistors R78 & R81 (20K ) sum the outputs of the VCO’s into the voltage divider comprised of R83 (20K ) & R84 (10K ). Transistor Q10 (2N3904) converts the level at its base into pulses between 0 volts and +5 volts for the octave generator, IC22.

*TEST PROCEDURE — mixer and level translator

Observe pulses on the collector of Q10 with an oscilloscope, or read approximately 2.0 volts AC ona volt meter. If not present, replace Q10.

*GATED OCTAVE ADDER

The final stage of background sound generation is accomplished by IC22 (74LS393). This chip is driven by the VCO and level translator and its four outputs are mixed together by resistor network R86-R90 to produce the sound waveform.

Outputs A-D are squarewaves that actually count the clock pulses arriving at pinl and represent these pulses as a four bit binary code. When the chip enable on pin 2 is held high by the input control circuitry latch IC9, 1C22 is disabled and pins 3, 4, 5, 6, all go low. No sound is generated with pin 2 held high. When pin 2 is held low by the CPU, the background sound is enabled. Outputs A-D begin pulsing and produce a complex voltage wave form at the junction of R89 & R90. The sound is coupled to

7 output pre-amp IC14 via resistor R91 &

32.

*TEST PROCEDURE — gated octave adder

Load all highs into input control latch IC9.

5-11 Gated octave adder IC22 should be disabled and pins 3, 4, 5, 6, should all read low. Jumper 1C22-2 low and observe pulses on pins 3, 4, 5, 6 with logic probe or scope. If pulses are at IC22-1 and any output is “dead”, replace IC22.

LASER & TORPEDO SOUND (block 3)

During game play, the ships attempting to “RIP OFF” fuel canisters from the center of the playfield protect themselves by firing short laser bursts at the defender ship. The defender ship in turn destroys these invaders by firing torpedo energy bursts. Both sounds are generated by identical circuitry with slight component value changes. The operation of the torpedo circuit is described:

Torpedo energy burst circuitry contains a VCO frequency control switch IC10 (7406), a VCO, bipolar-to-TTL converter and level translator Q9 (2N3904), and gated octave adder IC18 (74LS393). The three latter elements are identical in operation to those used in background sound generation (refer block 2 discussion).

The CPU enables a burst of torpedo fire by holding IC10-11 low thru 16 pin connector ribbon J4 via pin 14. A low onIC10 (7406) pin 11 opens the switch (refer Figure 1) and allows the voltage to rise on C28 (0.Imf). As this voltage increases, the VCO frequency of IC17-6 decreases. Transistor Q9 translates the large voltage swing of the VCO to +5 volt pulses which in turn clock gated octave adder IC18. Pins 3, 4, 5, 6 output squarewaves to resistor network R72-75 when chip enable pin 2 is held low. The torpedo burst waveform is AC coupled into pre-amp IC14 thru patch jumper W8 (refer to hints section) via C21 (0.68mf).

TEST PROCEDURES — torpedo sound

Observe pulses at VCO output IC17-6. Pulses should be square waves between +10 volts and -10 volts. With scope or logic probe, verify pulses from Q9 on pin 1 of IC18. Gated octave adder output pins IC18-3, 4, 5, & 6 should be low with CPU connector ribbon J4 removed. Tie IC 10-11 to ground. Pulses should be now present on IC18 pins 3, 4, 5, 6.

MOTOR 1 SOUND (block 4)

As the invader vehicles enter the playfield, a motor sound is generated. The audio waveform

Page 32

is the result of mixing rectangular waves of different frequency from oscillators IC11 (LM555) and IC13 (LM555). The mixed waveform is then fed to pin 2 of current controlled amplifier (CCA) IC 12 (CA3080A). The CPU enables the audio by closing a voltage switch made of Q4 & Q5. This voltage then drives a current through R36 to gate on [C12. Current amplifier 1C12 generates a current signal at pin 6 which is converted to a voltage at R19 (27K _). The signal is then AC coupled to pre-amp IC14 via C12 (0.1mf) from buffer IC7.

VOLTAGE SWITCH

Transistors Q4, Q5 and associated resistors form the voltage switch. The switch is disabled when the base of Q4 is held high by the CPU thru input control latch IC9. Q4 is now effectively out of the circuit and -3 volts appears at its collector via voltage divider R42, R43 and the -15 volt source. Q5 is effectively out of circuit (open) and allows no current flow, disabling the CCA (IC12). When the base of Q4 is held low, it turns on (closes) and drives current into the input of IC12, enabling motor audio.

*CCA

IC12 can be imagined as an amplifier that generates a current waveform characteristic of the voltage appearing at pin 2. The strength or gain of the output current is porportional to the current injected into pin 5 via R36 (refer to Fig. 2).

TEST PROCEDURE — motor 1 sound

Multivibrators IC11 & IC13 should produce pulses on pin3. This can be verified with a logic probe or oscilloscope. If missing, verify that capacitors C14 & C17 are not shorted. Verify that coupling capacitors C16 & C19 are not open.

*CCA

Cutting jumper patch W6 should turn off IC12. Temporarily jumpering the starred end of W6 to ground should turn the CCA on. If the CCA appears dead, cut jumpers W1 & W3 to isolate IC12 from other CCA’s which could be loading down IC12.

5-12 *VOLTAGE SWITCH

Load all highs into input control latch IC9. the base of Q4 should be approximately +5 volts. The collector should read -3 volts. With a jumper, ground the base of Q4. The collector should read +0.7 volts or greater. If not, replace Q4. Motor should now be audible. If no audio is heard, replace Q5.

BEEP SOUND (Block 5)

The beep audio occurs during game mode as invading ships enter into accelerated offensive levels and consequently become more difficult to destroy. The circuit has elements identical in operation and theory as the Motor 1 sound, namely, a voltage switch, CCA, and oscillator. The sound is a burst of several short tones and is controlled by the CPU thru input control latch IC9. The oscillator IC5 produces pulses on pin 3 which drive CCAIC6. The output of IC6 is gated by voltage switch Q2 & Q3 via gain resistor R18 (820K). Current controlled amplifier IC6 drives buffer IC7 via jumper patch W3.

TEST PROCEDURE

Refer to Motor 1 test procedure.

EXPLOSION SOUND (Block 7)

When a ship is destroyed, an explosion noise is enabled by the CPU thru connector J4 pin 16. The voltage switch for CCAIC3 is composed of one shot IC4 (LM555), Q1 (2N3906) and associated circuitry.

The collector of Q1 normally rests near -15 volts with Q1 off, disabling the CCA. When IC4-2 is pulsed low by the CPU it emits a momentary high to the emitter of Q1, turning it on hard. C8 changes very rapidly to +3 volts which enables the explosion audio via R10 (20K ). The output of IC4 then dies, cutting off Ql. Capacitor C8 slowly discharges through R10, gradually decreasing the explosion audio. Ic4, Ql, & C8 form a fast attack, slow decay circuit in this application.

IC1 (S2688) is a wideband random noise source that ouputs a complex signal of widely varying frequency. The frequency band of interest is separated by filter IC2 and its associated RC network and drives CCA IC3.

Page 33

CONTROL CURRENT

FIGURE 2

Page 34

The explosion waveform enters buffer IC7 via jumper patch W1.

TEST PROCEDURE — explosion sound

Noise generator IC1 should measure 4-7 volts AC with a volt meter. The output of IC2 is a very low frequency signal measuring 10-20 volts PK-to-PK on a scope.

With 16 pin ribbon cable J4 removed, tap IC4-2 to ground while observing output pin 3. There should be a high going pulse generated. The collector of Q1 should increase from -15 volts to about +3 volts. If the explosion cuts off hard C8 is open. If the explosion sounds like single or multiple tones or a broken record, replace IC1. If the explosion sounds garbled check D12, D13.

CCA

Refer to Motor 1 test procedure.

OUTPUT AMPLIFIER (Block 1)

The audio amplifier section consists of pre-

5-14 amp and volume pot driver IC14 (TL081), main driver amp IC15 (TLO81) and speaker drive transistors Q6 & Q7.

IC 14 drives the external volume pot located on the coin door and its associated cable. If no or very little volume is heard, meter the pot wires between JI-8 and JI-3. The resistance should vary as the pot is rotated. If the audio is at maximum volume regardless of the pot position, suspect an open circuit between ground and the pot lead connected to connector JI-1.

The final drive is a non-inverting amplifier circuit containing IC15, Q6 & Q7. Observe the waveform at the speaker wire at the emmitter junction of Q6 & Q7. If the upper half of any sound waveform appears clipped, suspect Q6. For lower half, Q7 is the suspect. For no audio meter Q6 & Q7 out of circuit and look for burned resistors R52 & R54.

Page 35

APPENDIX

Page 36

1 NPUT CONTROL CIRCUITRY

DAC INPUTS

BACKGROUND

BEEP

MOTOR

OUTPUT CIRCUITRY

LK5 cle

VOLTAGE FOLLOWER LKS.

LK4

FINAL AMP 1C15,Q6, Q7 iLK3_¢

TO ites SPEAKER

Lk2 FROM :

BACKGROUND SOUND VOL POT IS LOCATED BLK| ON COIN DOOR

5-15

Page 37

10 VOLT DAC CIRCUIT REF,

R25 R26 R76

R27? R28 FROM 1C9 (BLK 1)

R29 R30

BACKGROUND CIRCUIT

1c22 R86 -ROO

FILTER GEN.

WAVEFORM

RO1,C32 PREAMP (BLK!) = im Q10,R83 R84

ic9-9

BLK2

5-16

Page 38

LVS ey1g (179) WHOMLIN G2Y-22y *8I9! ON IAWNS Nad ot WHOISAVM yah aqqivo *LYANOO TLL OL dvodia vi-vr LINDYID OGads¥OL (ing) WHOML3N g$9y-z9u4 “BID! ONIWWNS wag Qt WHOSZAVM yah qa.ivo [e29) “LYANOO, TLL OL yv710d Id

920°9SH “N39 dnVy

JL Sl-ve LINDYIO YASVT

Page 39

MCTOR | CIRCUIT

TO VOLTAGE FOLLOWER p3e (BLK!)

a

  • WG ‘TTL TO NEG, VOLTAGE SWITCH

Q4,05

*CCA=CURRENT CONTROLLED AMPLIFIER

BLK4

5-18

Page 40

EXPLOSION CIRCUIT

wi ~ TO VOLTAGE FOLLOWER RIO (etki)

\x* lw J4-16

“LI

-15V

BEEP CIRCUIT

TO VOLTAGE FOLLOWER (BLK 1)

TTL TO NEG. VOLTAGE SWITCH IC9-12

Q2,Q3

BLKS

5-19

Page 41

DEFINITIONS

TTL (Transistor-Transistor Logic) compatible levels are defined as follows:

  • ATTL “low” or logic 0 is any voltage less than 0.8 volts.
  • A TTL “high” or logic 1 is any voltage greater than +2.4 volts but less than +5 volts.

VCO: Voltage Controlled Oscillator

CCA: Current Controlled Amplifier

IC: Intergrated Circuit (Chip)

NOTATION

A particular pin of an IC (Intergrated Circuit) is denoted in the text by first the chip designation and then the pin number: e.g. IC25-10 means Pin 10 of IC25.

A particular pin of a connector is denoted by first the connector designation and then the pin number: e.g. J4-15 means pin 15 of connector J4.

Jumper patches W1 thru W7 are sections ofa trace on the audio board designed to be severed in order to isolate a section of circuitry for test purposes. Be sure to sever between the two

5-20 eyelets and repair by adding a short jumper wire. DO NOT repair any trace by adding a blob of solder at the sever. This will cause intermittent operation.

CAUTIONS

Never connect pin 5 of a CA3080 (CCA) directly to ground or any other voltage. Failure to follow this rule can cause the IC to explode (also known as the plastic pop corn effect).

Never connect a TTL output to +5 volts. The plastic pop corn effect applies here also.

TEST EQUIPMENT

For troubleshooting this board you will need:

  • an inexpensive V.O.M.
  • logic probe — not necessary, but recommended
  • several jumper wires with “E-Z” hooks
  • an oscilloscope — same as item 2

TROUBLESHOOTING

All VCO outputs will measure 13 to 15 volts AC with a VOM (volt-ohm meter).

All 555 multivibrator outputs will measure 1.5 to 3 volts AC with a VOM.

Page 42

SECTION 6

MAINTENANCE

Page 43

UNIVERSAL BENCH TEST

CONFIGURATION

The components depicted in figure A represent the integral elements and interconnects necessary to effectively bench test the Cinematronics vector display video game system. The configuration is universal in that the game logic board A, display assembly B, and the power supply D are consistent from game to game. Audio board C varies in design for each new game though maintaining the pinout of its input power molex plug. Player control ribbon cable 3 terminates at the player control panel elements of each game (i.e. Joystick, Fire & Thrust buttons, Coin Acceptor Mechanism, etc.)

POWER INTERCONNECTS

The power supply D provides all voltages necessary for game operation (refer to main harness assembly drawing CA202201).

Logic board drive is +5 volts + 5% applied to pin 10 of the input power molex plug, & ground enters the logic board thru pin 4 to pins 1,5, and

  • The logic board will free run in the game attract mode with proper power applied.

The audio board accepts +25 volts on pin4 and -25 volts applied thru pin 6 to pin 8. Ground enters pin 7 and is trace connected to speaker return pin 5. Pin 9 accepts +5 volts DC.

Power dive for the display is +25 volts thru pin 6 of its molex plug to pin 5 and -25 volts on pin 8. The CRT filament voltage of 6.3 V.A.C. enters the display electronics through pins 1 & 7 viaa twisted pair of wires from the supply. A full wave rectified, unfiltered spot kill level of approximately +25 volts is applied to pin 14. The assembly is grounded thru pin 15 to pin 12.

SYSTEM TEST CONSIDERATIONS

As previously mentioned, the logic board A will free run in the particular game attract mode solely with +5 volt applied. Ribbon cables 1 & 2 are output lines and can be removed without affecting the free-run mode. Ribbon cable 3 is an input line and can also be removed for test purposes while free running. The audio board C can be effectively diagnosed with proper power applied and a speaker. The logic board generates most sounds by grounding various control lines through ribbon cable 2. The cable can be removed and game sounds can be generated by tying these lines low temporarily with a jumper wire. Refer to the appropriate audio board schematic and theory of operation section.

The display assembly cannot be powered up without data cable 1 from the logic board connected. With the cable open or improper data being fed from the logic board, the circuit breakers CB1 & CB2 on the power supply will trip indicating a load in excess of 3a being drawn from the +25 and -25 volt lines. Testing of the monitor requires a functional logic board. While troubleshooting a no display condition, it is recommended to remove the 8 pin moulded female plug from the neck of the CRT to protect the phosphor on the tube face from being burned by a high intensity spot.

TEST EQUIPMENT

For most test purposes, a wideband oscilloscope and a digital or analog multi-meter is adequate. Also, a tri-level logic probe for verifying the presence of digital information is recommended.

Testing and troubleshooting of the logic board is the least straightforward aspect of bench test. However, Cinematronics has developed a logic board exerciser to be used in conjunction with a signature analyser that allows effective troubleshooting & repair with a minimum knowledge of microprocessor theory and operation. The exerciser puts a 4 bit alphanumeric code on each IC leg of each chip on the CPU board which then can be probed & read with the signature analyser to verify proper operation. Contact the customer service department at Cinematronics for details.

TEST PROCEDURES

The first step in effective bench testing is to review the system theory of operation included in the manual. Discussed are principles from the mathematical concept of vector systems to the actual hardware techniques employed in

Page 44

generating a vector video game display.

For specific troubleshooting procedures, refer to the symptom-remedy diagnostic chart included in the manual.

6-2

Page 45

TO PLAYER CONTROLS

POWER SUPPLY 2921 MDL

fauDIO BoARD. —— 20720 [DISPLAY ASSY. _[PLIO0204" A PLIO0203 D Cc

FIGURE A MAIN HARNESS ASSY|PLIOOZ00

m

MATERIAL: DRAWN BY: DATE El Cajon

“| 2. TURLBER CINEMATRONICS [iNeumETeN DWG TITLE

PROJECTION: [SCALE: = +~®-| NONE |oove tent. SHEET | OF |

FIGURE A FINISH a gwanp | LEASE APPROVIDATE) “UNIVERSAL BENCH TEST

  • AEROS. CONFIGURATION 2 . TOLERANCE: UNLESS 3 OTHERWISE SPECIFIED OWG NO. 2 MN207800
Page 46

2 1 4 3 x REVISIONS

REV DESCRIPTION DATE | APPROVED,

PROPRIETARY

‘THIS DOCUMENT IS THE PROPERTY

OF CINEMATRONICS INC. AND IS

BE REPRODUCED OR

ED WITHOUT WRITTEN D

{TION OF CINEMATRONICS

RESET

jcecuir

WUPLOG REPAIR ® B

! :

i q cu ce =E¥OC CHECK aac +t0c loeepiro wo ves} |cc

El Calon DWG TITLE [sevease arenonfonre| SYSTEM TROUBLESHOOTING NOTES: UNLESS OTHERWISE SPECIFIED

4 3

6-4

Page 47

TABLE 6-1. TROUBLESHOOTING GUIDE

No Picture Listen for audible “clatter” from the deflection yoke on the CRT neck. If the clatter is present, deflection circuitry is working and the problem is in the intensity circuit.

If no high voltage, see NO HIGH VOLTAGE section.

If game audio is present, the CPU board is functional and the problem is in the monitor. If the audio is distorted or absent, the CPU board is suspect. If CPU board is equipped with red led near the input power plug, verify that it flashes once when power is applied and remains off thereafter. If no LED, verify that C8 pin 6 is constantly low with a voltmeter.

Check the neck of the CRT for a glowing filament. If there is no glow, check the brown & black twisted pair of the CRT plug for 6.3 volts AC.

Be sure all connections to the CPU board and monitor are firmly seated.

Connect a scope to the yellow wire leading to the CRT connector. Set brightness full clockwise. There should be an 80-100 volt DC base with pulses dropping down toa 40 volt level. Ifno pulses, probe U7 pin 4 witha scope and observe data pulses. If present, check Q2 & Q3 with an ohmeter or transistor tester.

Check cathode of CR5 for a full wave rectified, unfiltered voltage signal floating at +25 volts.

Check seating of CRT plug. Remove and probe with scope to verify presence of proper signals.

Narrow Line on Display Check for bad solder & crimp connections to yoke wires.

Check for open yoke windings with ohmeter. Verify continuity between display board and heat sunk eee transistors Q110, Q210, Q111 and Q211.

Check Q110, Q210, Q111, Q211 with ohmeter or transistor tester. Inspect solder connections on circuit board molex connector socket pins.

Half Picture Left Half: Check Q206, 208, 210 Right Half: Check Q207, 209, 211 Top Half: Check Q107, 109, 111 Bottom Half: Check Q106, 108, 110

Page 48

TABLE 6-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

fe Check solder connections on heat sink molex plugs J3 & J4.

Check diodes CR109, 110, 111 Check diodes CR209, 210, 211

Check transistors Q105, Q205

Check resistors R116, R216.

No Brightness Control Check intensity pot R11 for open wider or internal short. Check for open capacitor C17. Check for bad solder connections to R11.

Circuit Breakers Trip Disconnect power to display board. If circuit breakers continue to blow, check for shorted speaker coil. Verify that the output power transistors on audio board are good with an ohmeter or a transistor tester.

Observe L.E.D. on logic board near input power molex. LED should flash once when power is applied to game and remain off. For earlier versions not so equipped, probe C8 pin 6 with logic probe. Pin 6 should read low indicating CPU is not in continuous reset. Measure the voltage at T13 pins 10 & 20 with a voltmeter. The reading should be between 4.8 and 5.1 volts DC for normal system operation.

Remove connectors J3 and J4 on the display board and check power transistors Q110, Q111, Q210, and Q211 located on the heatsinks with an ohmeter or transistor checker. Check diodes CR114, 115, 214, 215, CR12 and CR15. Replace connectors J3 & J4. Check the horizontal DAC and vertical DAC for proper supply voltages on pins 13, 14, and 22. With an oscilloscope, check pin 15 for a+4 volt waveform centered about zero volts.

Verify a+2 volt peak to peak signal centered about zero volts at pin 6 of U102 and U202. Remove power and meter all deflection transistors in circuit, comparing a component located in the vertical channel with its counterpart in the horizontal channel.

Replace analog switch U1.

Picture on Display Jitters Check size pots R109 and R209 for wiper noise by turning briskly while observing the screen. Readjust for proper screen size.

Check for bad solder connections on R109 & R209.

Check DAC U101 & U201 for bad solder connections.

Insure that all molex connectors are properly seated.

Page 49

TABLE 6-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

Check analog switch U1 for faulty operation, loose connections to socket or poor solder connections.

No High Voltage If display board is equipped with KELTRON high voltage module, verify +25 volts input on J6 pin 4 molex. Verify +90 volts DC at J6 pin 1 and +400 volts DC at J6 pin 3.

Replace high voltage module.

On display board, read +18 volts DC at regulator U3. If missing, verify +25 volts present at input pin of U3.

Read -18 volts at regulator U5. If missing, verify -25 volts at input of U5.

Lift winding from pin 3 of high voltage transformer T1. Measure +18 volts at regulator U3. If now present, check for shorted Q4, shorted capacitors C18, C19, C20 and bad diodes CR7, CR8.

Check for 4.2KV AC at output wire of XFMR T1.

Replace XFMR T1.

Dotted Display Verify proper operation of U1. Check for proper +25 and -25 volts DC. Check operation of DAC’s U101 & U201. On logic board, check I 8 pin 2 for pulses. Verify presence at analog switch.

No Audio Check for open speaker coil. Check transistors 2N6292 and 2N6107 and nearby output components on audio board with ohmeter or transistor checker.

Check for open wiper on volume control mounted on inside of coin door.

Refer to audio board theory of operation and troubleshooting guide.

Replace F2 on logic board.

Coin Counter Check 2N6292 transistor on logic board with ohmeter or transistor is Inoperative tester. Verify proper operation of A4 by grounding A4 pin 1. Coin counter should click.

Disconnect coin counter molex connector. Measure DC voltage on red wire. Meter should read +25 volts DC.

6-7

Page 50

TABLE 6-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

EEE Gives No Credits Tie E4 pin 12 to ground. If credits fail to appear, replace E4. If credits appear, disconnect logic board ribbon connector J3. Measure +5 volts on A4 pins 1 & 5. If missing, replace pull up resistor pack C2.

Alternately ground A4 pins 1 & 5. If credits appear, problem is in switches on coin door. Verify proper coin door microswitch operation.

Reconnect J3. Observe A4 pins 3 & 6 alternately while depressing microswitch lever on coin mechanism. Pins 3 & 6 should change states. Replace A4.

Replace F2 (74LS259) on logic board.

Player Control Button(s) Refer to player control schematic in APPENDIX Inoperative Verify with ohmeter proper closure of player control leaf blade switches.

Remove J3 connector. Measure +5 volts on D4 - 1, 2, 3, 4, 12, 13, 14, 15. If missing, replace D4. Replace pull up resistor pack D2.

Measure +5 volts on C4 - 1, 2, 3, 4, 12, 13, 14, 15. If missing, replace C4. Replace pull up resistor pack C2.

Coin up a game and, with J3 disconnected, ground aforementioned pins on C4 & D4. If display responds problem is in continuity from J3 to player control switches.

Page 51

SECTION 7

PARTS LIST

Page 52

WCONHTIRWNH PART NUMBER

AM100600 AD207400 AD100404 AD100406

2119

2180 2181 AM100601 AD100405 MP203610 2128-A

MP205642 MP207002 AW207000

CA100200 CA100202

CA100202

2133 2138 2139 MFGR. DESCRIPTION PART NO.

Cabinet Assembly Control Panel Assembly Circuit Panel Assembly Monitor Assembly Power Supply Xentek #2921 Ribbon Cable Logic to Display Operators Manual

CABINET ASSEMBLY

PL100600

Cabinet Coin Box Cover Coin Box Coin Door Assembly Coin Meter Assembly Cover Plate, Front Face Shield, Display Grill, Speaker Speco #5713 Speaker Grommet, Rubber Lt. Fix. Smith #2188 Fixture, Florescent Lamp Florescent Lamp Bezel, CRT Plexiglass Screen CRT Decal, Side Lock, Rear Door Main Wire Harness Assy. A C Cord Assembly Flat Braid 34” Vol. Control Harn. Assy. Terminal Strip Cover, Terminal Strip Label, Patent Notice Label, Safety GND Notice Label, Unit Wired For Cap Film .01mf 600V = Wire Nuts Ideal #73 B Terminal, Ring Tongue Carriage Bolt 3/16”-1%4” Carriage Bolt 3/16”-1%,” Carriage Bolt 3/16”-2” Hex Nut 10-24 Wing Nut 3/16” 10-24 Wood Screw #8-56” Blk. Washer, #10 Small Pattern Washer, #10 Large Pattern

7-1 Pe HEN Pep Pe eee ee ee

ir) NVABWANYNE

Page 53

PART NUMBER MFGR. DESCRIPTION PART NO.

CA100205

MP207600

MP207001 MP205645 or AW207200

2132 A

CA207200

WL207200 Washer, #10 Int. Th. Lock Washer, #10 Ext. Th. Lock

VOLUME CONTROL HARN. ASSY.

PL100205

Pot. 10K JAIN056103 Molex Plug 3 Cir. 03-09-2038 Molex Female Socket 02-09-1118 Molex Male Pin 02-09-2118 Ty Raps T-18R Wire

CONTROL PANEL ASSEMBLY

PL207400

Control Panel, Wood Switch W/Mounting Brkt. WICO#15-0499-01 Button Assembly Long WICO#15-0405-01 Pal Nut WICO#19-0254-01 Plexiglass Instr. Panel Retainer, Player Cont. MP203606 P.C.B. Distribution Connector, Insul. Displ. IDT-26-1-T Ribbon Cable 26 Pin Molex Wafer Fric. Lock 09-65-1031 Swage Spacer Y,” Wood Screw #8%” Blk. Switch Wire Harness Assy. Leaf Switch-Replacement WICO#15-0677-01 BPeeH ooo PONE EH EEE

SWITCH WIRE HARNESS ASSY.

PL207200

Wire List Ty Raps Term. Female QK Disc.

CIRCUIT PANEL ASSEMBLY

PL100404

Mounting Plate

Page 54

DESCRIPTION

rPOMIAM AWD

WONIDAARwWNHE

DADRKHAWNHH AE100203 AE207201 2118 3066 3063 MP203611 38-105-22-01

$A100401 $A100408 37-LF 13331 $A100410

2169 2170 2136 2137

3063 3066 3065 3064 CPU P.C.B. Assembly Audio P.C.B. Assembly Ribbon Cable, Audio to CPU Lock Washer #6 Int. Th. 6-32-%4” Mach. Screw Rd. Bracket, Prom P.C.B. Assy. Prom P.C.B. Assembly 4-40-%” Mach. Screw Pan 4-40 Hex Nut

MONITOR ASSEMBLY KELTRON

PL100403

CRT 19” 19VARP4 Deflection Yoke Amplif. Display Sub-Assembly Analog Switch Yoke Assembly High Voltage Module Spring Mounting Bracket LH Mounting Bracket RH Label, High Voltage Label, Factory Adjust Only 4-40-4” M.S. Pan Hd. Ph. 6-32-44” M.S. Rd. Hd. Ph. #6 Lock Washer Int. Th. 6-32 Hex Nut #6-%” S.M.S. Hex Hd.

DEFLECTION YOKE AMPLIFIER

PL100401

Heat Sink Transistor Transistor Heat Sink Harness Long Heat Sink Harness Short Label, Warning Washer, Greaseless 6-32-14” Rd. Hd. Ph. M.S.

YOKE ASSEMBLY

PL100410

Yoke, Broy

7-3 HPwWWWWHH EEE EE NN HOOP EE

ORHEHE ENN

Page 55

CONIA ARWONH AE 2084 D

13-1103

3064 3083 3085 3084 SA300401 WL100208

10-5150 10-5330

10-5470

10-5101 10-5201 10-5331 10-5471 10-5821 10-5102 10-5182 10-5222 10-5302 10-5562

10-5103 MFGR. DESCRIPTION PART NO.

Molex, Female Pins Molex, Male Pins Molex, Connector

DISPLAY SUB-ASSEMBLY KELTRON

PL100409

Display P.C.B. Assembly Chassis CRT Socket 10K Pot. Allen Bradley Heat Sink — Thermalloy Heat Sink — Thermalloy Heat Sink — Thermalloy Neon Bulb Capacitor .05mf 1600VDC Wire, 18 Gage 9” Heat Shrink Tubing 3/16” Heat Shrink Tubing 3/16” Terminal, Ring Tongue #6-14” S.M.S. Hex Hd. 8-32-44” Rd. Hd. Ph. M.S. #8 Lock Washer Split Rg 8-32 Hex Nut Wire Harness H.V. Interconnect Wire, Pcs. 1-6

DISPLAY P.C.B. ASSY. KELTRON

PL100204

Resistor, 15 ohm %W 5%C Resistor, 33 ohm 4W 5%C Resistor, 47 ohm 4W 5%C

Resistor, 100 ohm 4%W 5%C

Resistor, 200 ohm 4W 5%C Resistor 330 ohm 4%W 5%C. Resistor, 470 ohm %4W 5%C Resistor, 820 ohm 4%W 5%C Resistor, 1K ohm 4W 5%C Resistor, 1.8K ohm 4%W 5%C Resistor, 2.2K ohm 4W 5%C Resistor, 3K ohm %W 5%C Resistor, 5.6K ohm ¥%W 5%C Resistor, 10K ohm %W 5%C

7-4 DMeENNNHEENNNNNNEDEHEE

NMWNHOHENNAYENYA DW NWN

a

Page 56

PART NUMBER DESCRIPTION

10-5683

11-5470 11-5222

11-5822 11-5103

12-502.7 12-5361 12-5103 13-5101

14-50.18 10-4142 10-4212 10-4103 12-1101 12-1502 101-104 31-1N914B

31-1N4003 37-7406 37-7805 37-7815 37-7915 37-TLO81P

33-2N2102 33-2N3904 33-2N3906

33-2N5210 33-2N5320

33-2N5322 33-2N5550 Resistor, 68K ohm 4W 5%C Resistor, 47 ohm 4W 5%C.

Resistor, 2.2K ohm 4W 5%C Resistor, 8.2K ohm 4W 5%C

Resistor, 10K ohm 4W 5%C Resistor, 2.7 ohm 1W 5%C

Resistor, 360 ohm 1W 5%C Resistor, 10K ohm 1W 5%C Resistor, 100 ohm 2W 5%C Resistor, .18 ohm 3W 5%C

Resistor, 1.43K ohm 4W 1% Resistor, 2.1K ohm 4W 1%MF Resistor, 10K ohm %W 1%MF Trimpot, 100 ohm Trimpot, 5K ohm Diode 1N914B Diode 1N4003 LC. Hex Inverter O.C. 1.C. Regulator +5V 1.C. Regulator +15V IC. Regulator -15V LLC. Op. Amp. TLO81 P LC. Digital Analog Con. Transistor 2N2102 Transistor 2N3904 Transistor ~ 2N3906 Transistor 2N5210 Transistor 2N5320 Transistor 2N5320 2N5322 Transistor 2N5550 Cap Disk .005mf 50V Cap Disk .1mf 50V Cap Disk .1mf 100V Cap Film .33mf 35V Cap Polycarb .022mf 200V Cap Dip Tant .47mf 35V Cap Dip Tant 1mf 35V Cap dip Tant 2.2mf 35V Cap Dip Tant 4.7mf 35V Cap elect 47mf 50V

7-5 an ep of

NWR NNER w

NHENHN NNANNA

Ne

Page 57

DESCRIPTION MFGR. PART NO.

CONDMAwWNHH 37-25LS181 37-74LS00 37-74LS02 37-74LS04 37-74LS08 37-74LS10 37-74LS27 37-74LS32 37-74LS75 37-74LS85 37-74LS86 37-74LS107 37-74LS151 37-74LS157 37-74LS 163 37-74LS164 37-74LS194 37-74LS257 37-74LS259 37-74LS298 37-74LS377 37-74LS393 37-74S00 37-74502 37-74S04 37-74S08 37-74S32 37-74S113 37-74S158 37-74S182 37-7425 37-74265 37-74S10 37-2101A2 2085 2086 Socket 16 Pin Molex, Male Pin Sold Tail Molex, Receptacle 15 Cir. Molex, Wafercon 6 Cir. Molex, Wafercon 6 Cir. Molex, Wafercon 6 Cir. Connector, P.C.B. 34 pin Printed Circuit Board

CPU P.C.B. ASSEMBLY

PL100203

ALU . Nand Gate Nor Gate . Hex Inverter Nand Gate Nand Gate Nor Gate Or Gate Quad D Latch . Mag Comparator . Exclusive Or Dual J-K Flip Flop 1 of 8 Data Selectors Quad Data Selector Binary Counter . 8 Bit Shift Regist 4 Bit Shift Regist. Tri-State Quad . 8 Bit Latch Quad 2-Input Multi. . Octal D Flip Flop Dual 4 Bit Counter Nand Gate Nor Gate Hex Inverter And Gate Or Gate Dual J-K Flip Flop Quad 2 to 1 Data Sel. Look Ahead Carry Dual 4 In Nor Gate Quad Comp. Output . Triple 3 In Nand . Ram 256X4 . Prom Drom 1 . Prom Drom 2 etotetstatalalaleteteletalalslotetetsisisleletotetetsialateterssiatels)

7-6 ICL-163-S6-T 02-09-2134 03-09-1152 09-18-5061 09-18-5062 09-18-5069

25LS181 74LS00 74LS02 74LS04 74LS08 74LS10 74LS27 74LS32 74LS75 74LS85 74LS86 74LS107 74LS151 74LS157 74LS163 74LS164 74LS194 74LS257 74LS259 74LS298 74LS377 74LS393 74S00 74S02 74804 74808 74832 748113 745158 745182 7425 74265 74810 2101A2 ener |

HE WH HEE EN NE NE NNANEWOPOCBRUPFWNHAHRWWNWER AW

Page 58

PART j MFGR. NUMBER DESCRIPTION PART NO. —=

2087 2088 2089 2090 37-2716 Pees LC. JS8722-07 7 Pole Dip Switch Crystal 20 MHz

31-1N914BDiode1N914 B
33-2N3904Transistor2N3904
33-2N6292Transistor2N6292

Cap Disk .02mf 50V Cap Disk 680pf 100V Cap Tant Dip .33mf 35V Cap Tant Dip 3.3mf 35V 10-5331 Resistor, 330 ohm %W 5%C 10-5471 Resistor, 470 ohm 4W 5%C Resistor, IK ohm 4W 5%C PRE RHE OE NRE

10-5102 10-5222 Resistor, 2.2K ohm 4W 5%C 10-5103 Resistor, 10K ohm 4W 5%C 10-5303 Resistor, 30K ohm 4W 5%C 10-5564 Resistor, 560K ohm %W 5%C 19-002 Resistor, Dip Pak 1K K27C Test Points Molex, Wafercon 12 Cir. 09-18-5127

609-1622MConnector, P.C.B., 16 PinAnsley
609-2622MConnector, P.C.B. 26 PinAnsley
609-3422MConnector, P.C.B. 34 PinAnsley

dumpers

ICL-143-S6-TSocket, Dip 14 PinRobinson/

Nugent ICL-163-S6-T | Socket, Dip 16 Pin Robinson/ Nugent P7, R7, T7, U7 | Socket, Dip 24 Pin ICL-246-S7-T 2076 H Printed Circuit Board 10-5101 Resistor, 100 ohm %4W 5%C L.E.D. TIL-220 & PRE EE RANE ENE

ix)

Peed

AUDIO P.C.B. ASSEMBLY

PL207201

Cap Disk 470pf 50V Cap Disk .005mf 50V Cap Disk .01mf 50V Cap Disk .1mf 50V Cap 4.7mf 35V Elect. or Tant.

7-7

Page 59

MFGR. PART DESCRIPTION Qty NUMBER PART NO.

Cap Elect 25mf 50V Sub. 22mf Cap Elect 100mf 50V Cap Film .01mf 35V Cap Film .022mf 35V Sub. .02mf Cap Film .047mf 35V Cap Film .1mf 35V Cap Film .22mf 35V Cap Film .68mf 35V Film or Tant Resistor, 150 ohm 4%W 5%C Resistor, 160 ohm 4W 5%C Resistor, 300 ohm 4%W 5%C Resistor, 330 ohm %W 5%C Resistor, 470 ohm 4W 5%C Resistor, 1K ohm 4W 5%C Resistor, 1.5K ohm ¥W 5%C Resistor, 2K ohm %W 5%C Resistor, 2.7K ohm ¥W 5%C Resistor, 3.3K ohm %W 5%C Resistor, 3.9K ohm ¥W 5%C Resistor, 4.7K ohm 4W 5%C Resistor, 8.2K ohm %W 5%C Resistor, 10K ohm ¥%W 5%C Resistor, 12K ohm ¥,W 5%C Resistor, 15K ohm 4W 5%C Resistor, 20K ohm %4W 5%C Resistor, 22K ohm ¥%W 5%C Resistor, 24K ohm ¥%W 5%C Resistor, 27K ohm ¥%W 5%C Resistor, 30K ohm 4W 5%C Resistor, 39K ohm 4%W 5%C Resistor, 43K ohm %W 5%C Resistor, 47K ohm ¥%W 5%C Resistor, 56K ohm ¥%W 5%C Resistor, 68K ohm %4W 5%C Resistor, 82K ohm 4%W 5%C Resistor, 330K ohm %4W 5%C Resistor, 470K ohm 4W 5%C Resistor, 820K ohm ¥%W 5%C Resistor, IM ohm ¥,W 5%C Resistor, 1.5M ohm 4W 5%C

37-7406LC. Inverter7406
37-7414LC. Trigger7414
Sub. 74164LC. Shift Register74LS164
Sub. 743771.C. Octal Latch74LS377
Sub. 743931.C. Counter74LS393

37-7815C 7815 C

37-7815CLC. Regulator +15V7815C
37-7915CI.C. Regulator -15V7915 C

° RE BE EE OEE POE ENE ODE NE HOWH OR RE HEN EP OWWWNHEWWHYNEEE

7-8

Page 60

PART MFGR. NUMBER DESCRIPTION PART NO.

37-CA3080E1.C. Transconduct Op AmpCA3080 E
37-LM555LC. TimerLM555

Sub. MM5837N | I.C. Noise Generator AMI S2688

Sub. 848 LF1.C. Op AmpTLO81 P
31-1N914BDiode1N914 B
31-1N5240Diode, Zener1N5240
33-2N3904Transistor2N3904
33-2N3906Transistor2N3906
33-2N6107Transistor2N6107
33-2N6292Transistor2N6292

Heat Sink Thermalloy 6071B Heat Sink Thermalloy 6072 B Header, P.C.B. 16 Pin 609-1622M Molex Wafercon 9 Cir. 09-18-5094 Molex Wafercon 6 Cir. 09-18-5069 4-40-14” M.S. Pan Hd. Ph Lock Washer #4 Int Th Hex Nut 4-40 AW207600 Printed Circuit Board i) BPOADDH HEN EP E ROWE EO Rw

COIN DOOR ASSEMBLY

PL100601

Coin Door Coin Mechanism Lock Carriage Bolt Blk Ox 3/16”-%” Lock Washer #10 Int Th Hex Nuts #10-24 Cable Clamps 4”

COIN METER ASSEMBLY

PL100405

Coin Meter E2B65D Diode 1N4003 Molex, Female Pin 02-09-118 Molex, Plug 3 Cir. 03-09-2038

A C CORD ASSEMBLY

PL100202

Power Cord Terminal, Spade #16 C10-401-P

7-9

Page 61

WL100203

16-5501 COIN SWITCH HARNESS ASSEMBLY

PL100203

Molex, Connector W/Lock Molex, Female Crimp Terminal Terminal, Female Quick Disconnect .187-.032 Wire 5 Pcs. Tie Wraps

POWER SUPPLY BLEED RESISTOR

PL100407

Power Supply Resistor, 500 ohm 5W 09-50-3031 08-50-0126

T-18R

Mdl 2921

Page 62

APPENDIX A

Assembly Drawings. Schematics & Wiring Diagrams

Page 63

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 64

WaLiium .noHLIM aainatwisio Pry 30 01 81 OMY “ON! BOINOWLYRENID. ALuagOUd 244 $1 1NBWNDOG BH vowsey [avo wousneesa Tass) Auviaiudoud

cn )

Page 65

WRiTTEN

VERT, DEFL. AMP

WORIZ.DEFL, AMP

8-3 WITEMISITY ADNUST

70 POWER HARNESS (POLARIZED)

54 PIS COAL.

NOTES: UNLESS OTHERWISE SPECIFIED

Page 66

_¥_ = — QalsIO3dS SSIMUIHLO SSZINN 'S3LON

80 31907 HaUMS NOLO xOLveaIO sani

Page 67

MELLIN LNOMLIM GauNEtMLsIO QNGOwsEY 38 OL LON ‘81 ONY “OHI SOINOWLVRENID 40 Auwaeows mL 81 ANaANDOG SOUL ewan [aiva [__nousacega Tass Auviaiudoud HORE

Page 68

af accum. secect @) "TO 20. MHz oer a

7406 osc SELECT COIN CONTROL COUNTER

oo con Lt negeren PAC!

SECONDARY

ACCUM,

FROM

DISPLAY “PROCEED” INPUT SELECT @ CONTROL

Recister TO AC 80 PANEL

c Q 02

PRIMARY ACCUM. (2)

LINE LENGTH COUNTER @) JGHHE TO LF13331 J RAM ADDR. 0) ADDRESS COUNTER ® J INSTRUCTION (ADDRESS 12 REGISTER fecal nam stonace ©)

SYSTEM a E SEQUENCE RAM DATA (:] (‘| [:| REGISTER (@) ane career INTENCITY CIRCUITRY

8-6

Page 69

‘a1sto3u8 361MUBHLO SSITINN 'SBLON Wre970 DLTNBHOS Ned S

su 9 vcs ~ Gea

Z "aw ey EP ST worn ed , (2 EL + s| z sa] arse, EP

(298) x OVI

oy,

Bra a, EPS suman

ee eR, FET ee Poa 8, er tied Fond ber 4 f wove BOLSIEY e,

  • 795) OVE 225TH

Sze, ro

i aT ;

I Td,

: , q

Sunant TOMINOD re mene Jeieibe wana wuweoMe3 18

ard § ae 0

HOO? UOLSIGRE

Pe s #7 zm «| inst “oa 2| o| Fae

at wd i a if 7 wT { ee

  • aay wi | | it iN a nae car wate wave WOLcIeay ceges AuvaNUDIS °C 1G 70

ure wz

Tanda WO ve EH TLD Ge ann TORO CAL Wt SORE

8-7

Page 70

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 71

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 72

ra

D D

(498,48

c c

4 Le . Ws AEE

a

3 te ane) sar > — SERDELD 3] 3% jee e012 pg LE ls 8 ° woe SELL

i| - ~ co 503) ES

(608, 5C4, $85, 584)

4 2 °t505 504) oer A

m {Pe sa i wy [rovenance: pacess. i “BER — Rae oe i , [aorecrion [scar

a f= ous i (IDG. 186, 184,383. 3A3,3 86) 5 8 T 7

Page 73

er) «ace xr) nace,

  • oaeey (eos) ate

NOTES: UNLESS OTHERWISE SPECIFIED

Page 74

8 q 6

BoE a aa ae =a i aaa

I !

  • Leo Luo} 1 —_| az scan p HEAR Afgan ausus reap 4 D D a 76

a app

Pay : 780) pay

en uTARZe Sut) pace VECTOR _¢ —3) Fao ia NTI wre 5) TaeeT

Sat c c

craw swe) “S. UNE DRAWINGS 5 yo.4q _ le B

[2s eI ob tee Ph Py Hy Ste Sy She Lhe i in| al le coeur >LECTOR_iy

TALS S77 |e A us ERATE cncrarncwcs SN

=O Gy Bz Oy By Bs O Gy Oe Litre

TTT To SUMsRAM

"50100203, NOTES: UNLESS OTHERWISE SPECIFIED _{7 RRBAIILE $ z [saree

4 T 3 T 2 I 1

8-12

Page 75

v2 03-09-2041

PART OF Jt

o3"08-2122 +5V RTH eS (6nD> Few. 100, 115, weRECT

u \T. [Wernaee [reauieess [coNnBerionl woovac[1702,3 704] 1 AN S| isvac_ [ito 23 T04] 1 An0« | [2sovac Tc vos T TANC a) (Z]REcommENDED FUSING; 3A SLO BLO FOR 115V. 1,54 SLO BLO FOR 230V [i] tRansFoRMER SHOWN WIRED FOR I1SVAC OPERATION

NOTES:

Page 76

Br oN Ba Bare BaLLoMND 27-7 aaNOMS BEMARLO SENT Aly IO MOBY Saw waLsESD Te (o2W0RS HNMHLO S870 COON! AoW SIRO YE

Page 77

I =i —T E| 200105 | 406 Fel a DLP WHOS SINCE 73 AVES uu daa

(93140348 35™MUSHLO SS31NN 'S3LON ‘sya nes sanrW ZaLeI9Fe Ty ‘SOVARICEOIH Ml Ba Satie BALD T'S ses TTS a

Ee)

Page 78

8-16 <x ver or SAINTS PROPRIETARY THIS DOCUMENT IS THE PROPERTY OF CINEMATRONICS INC. AND 1S NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT WRITTEN AUTHORIZATION OF CINEMATRONICS.

we, (VERTICAL) MOLEX COMM.- PA. O8-09- 1063 (IEA), MOLEX MALE PIN - PN. 02-08-2118 (EA. MOLEX FEMALE SOCKET: PN. 08-09-1118 (SEA).

U4 . REF, SD203201 CHORIZONTAL) (J3, REF. SDE08ZO}- Fe MSs Fq@ Fs Fea Fu NOTES: UNLESS OTHERWISE SPECIFIED \ 500 133; ~ THERMALLOY TRAMS. SOCKET PUBS -PF-603 (GEA), REVISIONS. Rev DESCRIPTION DATE | APPROVED,

GAAY OF BLUE in J~ }_—

BLACK AED |

WHITE OB WAT/YEL ORANGE © 25878

L= J

h-—+ 238———}mo 3.30 HEAT SINK HARNESS, 2/78 XL HEAT SINK, 2107-A

WHITE OR WHT/ VEL.

ORANGE {| ©) be

Gey OF BLUE BLACK GREEN 2USB76 ©

a OO

\ EAT SILK HARNESS, 2179 MOLEX COUW -F1/.08-09- 1068 (1A). MOLEX MALE Piki- PAL. 02-09 +2//8 (JEA.), MOLEX FEMALE SOCKET- PA). 08-09-1/18 (SEA). a HEAT SIKIK,2107-A SHEET) OF7

Page 79

>

8 7 |

PROPRIETARY

ced 1c9 usa7rd-}

eeetecg TTTTTTTT

3 SDENCTES SIDE CF JUMPER CONNECTED TO RES

AXCAP CAN BE SUBSTITUTED IF MORE THAN ONE LETTER IS USED

4 CAF WITHOUT REF DES ARE BYPASS CAPS

Z.ALL CAR VALUES ARE IN uf,

  • SLL SES. VALUES ARE IN nM, (/W 2% 2LL DIQDES MARKED 214 ARE 1914

NOTES: UNLESS OTHERWISE SPECIFIED

7 6

Page 80

8 z 6 5 4 4 3 1 propaierany 5 3

>| PERECO OF FETE po cs Lace RIS AIK 905 UNUSED Gares aro ma i > 4 6 ace

ap cu cig DB 10 acs Lee . rilele Be 88 a “re

3 Hy 3 itlob's

3 Jicee -ssas 4-16 £ EXPLOSION 6

2Grr le Zh i, age | Bord

C23 4708 D O#

Keose rt 2 55 ass SPEAAE? Fi 23k id

a 30 eneiozlar 225 y Foro 33k 5 jf

8-18 1K Be) | ees sree EE OK = REO ASK 20K 9 S83 Re? 20K] i pussoe | 1/25). REE 39K

TLOBI Ree me L = Red 62k] A515 OPTIONAL Sing = 5 OR 7 LAST RET. DES. USED: 41, C42 Tz, HIO,ICZS pris oO > a F Weis DES. MOT WEED AME C322 f ge | i e1T = VOLUME CONTROL (10K POTD MOUNTED ON = Osseo . a eet foo 4, ADD ONE BYPASS C2 (BEW.EEN ONG 4157 tof 7 cASOBOE F001 = 2192-4 ena [cmetuarnowes Bd aa FO9 EVERY TWO TC PACKAGES LISING +5 1s} 7 EAPACITOR LEGEND 2-302 Je aoe

  • ALL C:G0ES ARE Im EXCEPT OD Prilia Eo ELECTHOUITIC GND fowa mE SCHEMATIC]
  • ll Bes. atUes FEIN OuMEING Hp sf 7 = is J2-5 eNO es -5,7 “s:| AUDIO BOARD - RIP OFF 1 ALL OLE VA UES ARE IMLa6 SOV. me cr a NOTES: UNLESS OTHERWISE SPECIFIED ‘| 5020

a 8 7 6 5 f 4 3

Page 81

8-19 4 | 3 ___+ 2 al = INTERCONNECT BG GARD

PROPRIETARY 3 PO! MOUNTED TO SIDE OF FRONT PANEL

PLAYER CONTROL PANEL

REAR VIEW

FIRST SECOND

PLAYER PLAYER

ONE FIRE FORWARD RIGHT LEFT © START_-—s FIRE. «FORWARD. RIGHT =—LEFT

COIN SWITCHES

RIBBON CABLE TO t pis!

CPU 2i Ge tO OULNOD_YBAV Td

a

& S3HOLIMS 26¢ a ' ono ¢ Pl r ' Jl H vL-4 fl ' £1 Cajon

NOTES: UNLESS OTHERWISE SPECIFIED

Pas 4 3

Page 82

~~ NOT USED

4 | 3 ¥ 2 1

‘THIS DOCUMENT IS THE PROPERTY

OF CINEWATRONICS INC. AND IS

NOT TO BE REPRODUCED OR

D | stmeureo witnour warrren AUTHORIZATION OF CINEMATRONICS. ne.

WIRE LIST

[cour [ AWG. | PIN [LENGTH] REMARKS

LENGTH | REMARKS [TWISTED - CAMP [WHITE 1 PER INCH

INOT USED.

[FROM | Ha4-1 Fat [ene | 22 _|MALE H4-2 [SPEAKER |GREEN | 22 [FEMALE

22 bl

VOLUME REF +25 ‘At Ling [SHEEN H4-4 RED CORD. [WHITE JiB x3 [ H4-5 [SPEAKER[BLACK w/PLUGIBLACK [Hat [W228 | | |” REF -25 13-1 }eROWN | Ze PRBTED-TPER ZA LC a W371 |WuiTe | 22 NER. 3 VAC H4-8 [H7-3 Teuwe [az [| VOLUME, -u | H314 (YELLOW | 22 SPOT MILL H4.8 | H2-4 a REF +5 Cc H5-G [RED {18 COIN METER!

T_|Ha-4_ | RED

HS

H5-1 [44-4 MALE REF H5-2 __[ NOT USED H5-3 MALE. REF

Not USED NOT USED 43-8 | BLUE Hal

Ho

=== ar W212 REF GNO H3-12 [| __~*(FEMALE| REF. GND

NOT USED [NOT DsED DISPLAY REF 3VAL NOT USED 3 NOT USED) NOT USED

NOT USED REF. +5)

  • USED NOT USED B _[Nor use) NOT_USED

REF 425 VOLUME. FEMALE, REF REE i.4 VAC HT MALE REF REF = 25 NOT USED NOT USED NOT USED. 4 18 GND

FEF, +5 REF SPOT KILL REF_GND

sctoare]OWG TITLE a MAIN HARNESS ASSY. Fine:

pwe wo. NOTES: UNLESS OTHERWISE SPECIFIED ae ee

~@-|NONE [eooe went ‘SHEET Z OF 2 one 192 13

4 3 + 2

8-20

Page 83

‘SPEAHER #22 BLM FROM AUDIO 22 Gane AP Lae a D 18 AW. BLK y9 WS ana, wer, TMISTED

AC LINE CORD WITH PLUG

(4e" LONG) FROM POWER

HO com METER: LE os: 071038

  • 22ANG, RED FROM AUDIO 25 22aWG. BAN FROM LOGIE

MALE PIKIS

8-21

VOLUME MALE PINS

<ebea) 03.01-1087 v4) 8 ANG, BLK. TD Las fa lean. WaT To Lane

‘FaIsteD

FEMALE PI Nia os-08 1122 POWER SUPRY Hz MALE PINS,

ware Bac i oxen ore lacs UNE coRD

He , FEMALE PIS EXCEPT PIN-+ vsren fed 224NG, Bin, FROM OHSELAY i AEP came pis EXCEPT PIN! vwsren (SS $Me Bi: HM

SANs Gm CoML METER “#1 22 AWG GREEN TO VOLUME fait OR! a

32539

2 at 7p wow, as (ANG RUE Tet sruar TRBEE eeeaepee gee ati ae

4 an ANG. ORG. TD WOID $4 22 ana. SWE To vow fg Awe, ORG. FROM DiceLar 35 HE ANS. Sad. Post aoe AWG. ORG. TD LOGIC AAG. BLK. To AUD AMG. BLM. FROM OISPLAY Hy g OISPLAY i i

Page 84

SUGGESTED PARTS FOR STOCK

It is recommended that the following list of parts be maintained in the event servicing of your game becomes necessary:

MONITOR

DAC-80 — LF 13331 — TLO81 — *7818 9 — *7918 7815 — 7915 — 2N5876 — 2N5878 — 7406 —

LOGIC digital to analog converter high speed analog switch operational amplifier +18 volt regulator ~18 volt regulator +15 volt regulator -15 volt regulator PNP power transistor NPN power transistor inverter package

Masked ROMS — particular to each game D-ROMS (1-6) — custom programmed 74LS32 74LS259 —Ic

  • Audio/Coin circuit IC

*Necessary only if monitor is not equipped with Keltron H.V. Module.

8-22