CATHODE RAY TOMES

Pepper II

Pepper II (version 8) (Exidy, 1982) · Manual · 69 pages · 20 sections · original scan

Page 1

Pepper II

Operation and Service Manadl T Edition

Page 2

PEPPER I1™

Operation and Service Manual 1st Edition

© 1982 Exidy, Inc. 390 Java Drive, Sunnyvale, California 94086-1271 Telephone: (408) 734-9410 Toll-free: (800) 538-8402 Telex: 357-499 (EXIDY MNTV) Exidy Ireland Gortlandroe Industrial Estate Nenagh, County Tipperary treland Telephone: (067) 32555 Telex: 70009 (EXDY E1)

Page 3

EXIDY PEPPER II" OPERATION AND SERVICE MANUAL

TABLE OF CONTENTS

  • PRELIMINARY PROCEDURES ...cccccccsccscccccceeveee 1

A. GAME INSPECTION seseeceseeee

  • Filing a Claim .....05
  • Visual Inspection ssecceeeee

o INSTALLATION cecccccccccccccccccccccscecccces 2

C. PRELIMINARY CHECKOUT PROCEDURE .ccceeseseceee 2

D. ADJUSTMENTS ccsccccccsccccccccccscsssceeseeee

  • Power Supply Information and Adjustments .
  • Audio Board Adjustments cececscccececveves
  • Operator Selectable Options w..sseceseseee a. Coinage b. Number of Turns c. Bonus Turns Rwww

TL. MODES OF OPERATION ...scccscccssccccvessesecvens 6

As AUTOMATIC SELF-TEST MODE ..

  • Logic Diagnostic Tests ssceccessssceeseees 6 a. The RAM Test. b. The ROM Test
  • Audio Diagnostic Tests ssccsscecccceseeves 7
  • Control and Color Diangostic Testsesseeseee 8

B. THE ATTRACT MODE .eoeee see nececeeececes F

C. INTRODUCTION MODE ceccecccccccnccvecvccccsves 9

D. GAME PLAY MODE cecccceccccsccccevvcsecveseee 10

  • Obstacles and Hazards
  • SCOFINg eeeeceeseeee seeecceeveceee 10 see eecceecececeeee 10

E. VANITY MODE ccecccccccccccssccccecsecesesece 10

Page 4

APPENDIX A: SCHEMATICS

MEMORY MAP .ccvccccccscevcccccccccscscscsesees And

Page

Page

Page

Page

Page

Page

Page

Page 1: GAME LOGIC cocecesccccceeccccccesscees And

Master Oscillator, Element (Horizontal)

Counters, Line (Vertical) Counters, Screen RAM Addresses, Coin Input Decoding, Hardware Generated Line Positioning Proms, Blanking and Video Clocking, Black and White Composite Video Output

2 LOQIC ceeccecscccccccccvcccccccccceees An3 Screen Controller PROM, Screen RAM Character Image Storage, PROM Power and_ Signal Selection, Character Generator Output Shift Register

3: Plane Interface Board .sceceseseceecee And Character Generator Image Storage RAM

4: LOZIC seccceccccececcveccccccccccscees AnS The 6502 Microprocessor, Power-on Reset circuit, Processor Workspace RAM, Main Address Decoding

5: LOgic eeccesee eee AGB Program Memory, PROM Address Selection, Memory Device ‘Personality* Selection

6: LOGIC ceccecccccccccncccccccsccccccces AnZ Moving Object Horizontal Position, Moving Object Vertical Position Counters, ‘Write Moving Object" Decoding, Color Interface Output

7: LOGIC cocceceveee eevee eeeceereeeece AWB Moving Object Multiplexing, Moving Objects Image PROM, Moving Object Video Output Shift Registers, Moving Objects Shift Register Load Logic, Moving Object Shift Register Control Logic, Memory Device Personality Configuration

B Of B: LOGIC coeeeccccecccevccccesccsses AWD Interrupt Status Latch , Option Switch Port, Control Inputs Port, Moving Image Latch, Audio Board Port, Control Port Latch, I/O Decoding

Page 5

AUDIO/COLOR PCB-GENERAL DESCRIPTION ...eeeeee. A-10

Page 1: Audio/Colorecsececcaccceccvesesescsees An

Page

Page

Page 4: Audio/Coloresesecesecece

Page Logic and Power Interface, Communications and Address Decoding

6502 Microprocessor, Peripheral Interface Adapters, Address Decoding, Music Generator, Master Oscillator, Program Memory, Output Filter

Clock Manipulation and Noise Generation Circuit, Amplitude Modulation Control, Output Summation and Volume Control

Summing Amplifier, Integrator and Audio Power Amplifier

Pattern Character Color Division, Priority Encoder, Color Data Latches, Color Selection Multiplexers, Video and Sync Signal Polarity Selection, Final Video Output Re-sychronization

Wiring Harness Diagrams Main Harness, Control Panel Harness, Coin Door Harness, Electrical Schematic for Universal Power Supply

APPENDIX B: ILLUSTRATED PARTS LIST

A.

B.

c.

dD. FINAL ASSEMBLY sscceccssccccccccecccsccsececuce

CONTROL PANEL ASSEMBLY scsssssccccccccccccseves

JOYSTICK .seee

UNIVERSAL POWER SUPPLY sececcsccccccccccccscene

ISOLATION TRANSFORMER ASSEMBLY cssccesseccecees

COIN DOOR ASSEMBLY sececssssscccccceees

LOGIC AND AUDIO BOARD ASSEMBLY ceceeeecceeeeees

PRINTED CIRCUIT, UNIVERSAL POWER SUPPLY ...eeee 5: Audio/Colorecessscccccccccccceccccsees AW15 2: Audio/Color ssecsecccscccvcccevcccsces An12

3B: AUdiO/COlOr cecesceeccccesccecescccees An13

eee ceceeeeeee AnT4

B-9

LOGIC BOARD .ecescscccccsccccccecccececesseces B10

AUDIO/COLOR BOARD ASSEMBLY «sccceceeccsevcceeee B11

PLANE INTERFACE BOARD .secceesevesecceeee eoeee BH13

Page 6

COPY RIGHT

Copyright © 1982 by Exidy Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, or by any means without the prior written permission of Exidy, Inc. 390 Java Drive, Sunnyvale, California 94806.

DISCLAIMER

Exidy Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantibility or fitness for any particular purpose. Further, Exidy Inc. reserves the right to revise this publication from time to time in the content hereof without obligation of Exidy Inc. to notify any person of such revision or changes.

TRADEMARKS

PEPPER II™ is a trademark of Exidy Inc.

WARNING

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manuals, may cause interference to radio communications. As temporarily permitted by regulation, it has not been tested for compliance with the limits for Class A computing devices pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Page 7

FOREWORD

Part One of this manual is on Preliminary Procedures, describing game inspection, installation, and checkout. Also, adjustment procedures are given for power supply, audio volume, and Selectable Options.

Part Two, Modes of Operation, describes the four PEPPER II modes: Automatic Self-Diagnostic Test Mode, Attract Mode, Game Play Mode, and Vanity Mode.

Appendix A contains game schematics, with a circuit description on the page opposite them.

Appendix B is the Illustrated Parts List. Parts are pointed out in the drawings and listed opposite each drawing.

Page 8

I, PRELIMINARY PROCEDURES

A. GAME INSPECTION

All Exidy equipment is carefully packaged in well-padded cardboard containers to prevent damage during shipment. Before signing the delivery receipt, you should follow this procedure:

  • Check for obvious damage and make certain that the physical piece count of the shipment matches the piece count on the bill of lading. These two procedures should always be done before signing the delivery receipt.
  • Shortages and/or obvious damage to the packaging on any given shipment should be noted in writing on the delivery receipt before signing for the delivery.
  • If concealed damage is suspected on any shipment, those packages believed to contain the damaged goods should be opened in the presence of the delivery driver. If the goods have sustained concealed damage, a description of said damage should be noted in writing on the delivery receipt before signing for the delivery.
  • Never apply power to any game with noticeable damage.
  • Filing a Claim

To file a claim, follow this procedure:

  • Any and all damaged freight, including packaging, should be retained by the consignee until a physical inspection of said freight can be made by a representative of the carrier involved.
  • The Claims Manager for the carrier involved should be notified as soon as possible, after the damaged goods are received. Preferably, the carrier's Claims Manager should be notified within forty-eight (48) hours of receipt of the goods by the consignee.
  • If warranted, a written claim should be filed with the carrier involved. A detailed description of the damage(s) should be provided and copies of all supporting documents, including bill of lading and/or delivery receipt, inspection report, and invoice, should be attached.
  • The sooner a claim is filed, the better for all parties concerned. The carrier against which a claim is filed is required, by law, to respond to (acknowledge) that claim within thirty (30) days of receiving same and must reach a final disposition in the matter within one hundred twenty (120) days.
  • Visual Inspection
  • Remove the rear access door with the appropriate packaged key.
  • Examine each major and electrical component thoroughly for scrapes, dents, broken or missing parts and loose or missing screws.
  • Check for loose cable connectors.
Page 9
  • Visually verify that all the integrated circuit devices (IC's) plugged into sockets are properly seated and that no IC pins are bent or misaligned.

If you find any damage during this inspection, file a claim with the carrier. Send a complete report of the damage to Exidy Inc.

B. INSTALLATION

Planning the location of the game should involve both physical and electrical considerations. Such physical considerations concern the placement of the equipment with respect to these clearances:

Height: 72.50 inches, 184.2 cm. Width: 25.50 inches, 64.8 cm. Depth: 31.00 inches, 78.7 cm.

An indoor, relatively dust-free environment is necessary, with proper conditions required of any electrical component. Electrical considerations include availability of an AC outlet with the correct voltage and frequency. You should consider the working space required for technicians and operators incuding access to the rear of the game.

NOTE: The cabinet must be within five feet of an AC outlet. Be certain that a ground jack or terminal is available at the outlet.
CAUTION: DO NOT remove the AC ground prong from the plug. Doing so voids your warranty!

C. PRELIMINARY CHECKOUT PROCEDURE

After properly installing PEPPER 11™, we suggest following this procedure to check its operation:

  • Plug the AC jack into the AC outlet.
  • Once powered up, after five seconds of silence, a quick beep sounding like an organ chord, is heard. This is part of the Exidy Audio Diagnostic Test. A single beep indicates all is well with the audio board. 1f more than one beep is heard, consult Part Il, Automatic Diagnostic Test Mode.
  • Allow 8-10 seconds to pass for the CRT to warm up.
  • Observe the TV monitor display to assure the correct attract mode is present on the screen, as described in Part || B, Attract Mode. If the PEPPER I1™ display is incorrect, contact Exidy Customer Service Department.
  • Insert the appropriate coin or token into either of the coin slots. All the messages in the attract mode will flash the following line:
Page 10

PRESS PLAYER ONE START or PRESS ONE OR TWO PLAYER START

depending on the number of coins dropped into the coin slot.

6 Press one or two player start and play the game to verify that all screen images are displayed as described in Part I! D, Game Play Mode.

NOTE:

Screen colors may possibly be affected by the relative position of the game with respect to the earth's magnetic field. If this condition occurs on your game we suggest rotating the game to the RIGHT or LEFT. Also, by powering the game ON and OFF, the internal degaussing unit should eliminate any color deficiencies. In the event that this does not correct the monitor colors, externally degaussing the game will eliminate the affected colors.

If assistance or repairs are necessary, contact the Exidy Customer Service Department, (800) 538-8402.

D. ADJUSTMENTS

  • Power Supply Information and Adjustments

All DC Power required to operate PEPPER I|™ is supplied in the Exidy Power Supply Module. These supply outputs are as follows:

+5v DC@6 amps
-5v DC7.@1 amp
+12v DC (HI)@3 amps
+12v DC (HI)@1 amp
-12v OC (HI)"@3 amps
-12v DC (LO)@1 amp
  • (HI) refers to “high current" (LO) refers to “low current"
CAUTION: Only certified technicians should make adjustments on all components of PEPPER II™. AC line voltage selection is available in your PEPPER I1™ game by setting the appropriate jumpers on the power chassis. Only the +5v DC is adjustable. This must be adjusted to:

+5.00v DC +/- .25v

as measured on the PCB near the microprocessor (location 2A).

  • Audio Board Adjustments

The following drawing points out the three individual audio adjustments and the location of the DIP switch. The audio board rides piggyback on the logic board, mounted on the right wall of the game, when viewed from the rear service door.

Page 11

MASTER VOLUME

SPECIAL EFFECTS 7 VOLUME

lon

f f—— MUSIC VOLUME

S POSITION DIP SWITCH

  • Operator Selectable Options

PEPPER II™ has several switch selectable options controlled by an 8-position DIP switch located on the main logic board at position 16A. This switch is accessible through the back door of the game.

PEPPER II™ is shipped with the dip switch already set for optimum dollar return. Should you decide to change the settings, you may select any of the following options by setting the proper switch accordingly:

a. COINAGE Switch Switch Switch

458
1 Coin - 1 CreditOFFOFFOFF
2 Coins - 1 CreditOFFONOFF
1 Coin - 2 CreditsONOFFOFF
1 Coin - 4 CreditsONONOFF
1 Coin - 3 CreditsOFFONON

OR 2 Coins - 7 Credits

Page 12

ae COINAGE (continued)

1 Coin in Left Slot- 1 Credit, 1 Coin in Right Slot- 5 Credits

1 Coin in Left Slot- 1 Credit, 1 Coin in Right Slot- 4 Credits

2 Coins in Left Slot- 1 Credit,1 Coin in Right Slot- 3 Credits

b. NUMBER OF TURNS

2 Turns

3 Turns

4 Turns

5 Turns

c. BONUS TURNS (Extra turn awarded when selectable number of points are made).

40,000

50,000

0000-60000

Jy 000 77r00 Switch

OFF

Switch

OFF

ON

OFF

Switch

OFF

OFF Switch

OFF

OFF

Switch

OFF

OFF

Switch

OFF

OFF Switch

Page 13

Il, MODES OF OPERATION

A. AUTOMATIC SELF-TEST MODE

PEPPER II™ automatically tests the logic and audio boards on power up. To run the Control and Color Test, activate the coin switch while powering up.

You may bypass both diagnostic modes by depressing either the one or two player start button while powering up. After 8 seconds of the message "STAND BY VERSION X", (where X is a number representing the software version) the Attract Mode appears.

  • LOGIC DIAGNOSTIC TESTS

a. The RAM Test

When PEPPER II™ is first turned on, a processor and video RAM test is done. If the RAM passes, it goes immediately into the ROM test, without a message indicating it passed the RAM test.

If a RAM chip fails, an attempt is made to indicate the RAM chip where a failure was detected. Since the screen depends on a properly functioning RAM, this indication may not be displayed. A failed RAM may be indicated by a digit from 0 to 7 in every position on the screen using four colors. The code for these digits is as follows:

Number Number on RAM chip Screen to check

05AProcessor RAM
14Afailure
28BScreen RAM
37Bfailure

4 11C

513CVideo RAM
612€failure

7 14C

The RAM test cycles if the failure is persistent.

b. The ROM Test

If the RAM test passes, the ROM test begins. The message STAND BY VERSION N appears on the screen (where N is a number). One by one, "X"'s appear on the screen. Each X indicates half (2K) of a ROM board chip, numbered 6A through 13A, has passed the diagnostic test. After all marks appear, the game then goes into the Attract Mode, indicating all is well.

If any failure is detected during the ROM test, a hex digit appears instead of an exclamation point with a "BAD ROM" message at the top of the screen. The test tepeats indefinately if a bad ROM is encountered. The key for which chip to check is as follows:

Page 14

Message: ROM Chip to check:

MESSAGE: CHIP TO CHECK:

8 prom7 prom6 prom

0 lower 2K of 13A 1 upper 2K of 13A

2(0)lower 2K of 12A
31upper 2K of 12A
420lower 2K of 11A
531upper 2K of 11A
642lower 2K of 10A
753upper 2K of 10A
864lower 2K of 9A
975upper 2K of 9A
A86lower 2K of 8A
B97upper 2K of 8A
cA8lower 2K of 7A
DB9upper 2K of 7A
ECcAlower 2K of 6A
FDBupper 2K of 6A
  • AUDIO DIAGNOSTIC TESTS

While the Logic tests are underway, the Audio board is also being checked.

Five seconds after power on, one or more quick beeps, like an organ chord, are heard. This is part of the Exidy Audio Diagnostic Test. The number of beeps that sound indicate different conditions of the Audio board. The following code is an indication only, of where to first check the Audio Board. Because this diagnostic test only evaluates certain components, other circuitry is relied upon for the test. Should this other circuitry fail, the diagnostic test may not, then, point directly to the failure. Please use the results of this test as a guideline for further troubleshooting.

The code is as follows:

0 beep: If no beeps are heard, along with a hum or random notes, this may indicate a failure in 3A and/or 7A.

1 beep: All audio hardware is OK. However, be sure to check the Attract Mode Cycle anyway for a possible message to check the Audio Board. In occasional instances, this can occur. The message will further direct you.

2 beeps: ZERO PAGE RAM failure. Check 6532 RAM 1.0. Timer Array at location 7B on the board

3 beeps: (will not occur)

4 beeps: ROM failure

Page 15

5 beeps: INTERRUPT failure. Check 6532 at location 7B.

in addition, this message appears during the Attract Mode only if the Audio Board needs to be checked:

"CHECK AUDIO BOARD*

XxX YY

XX and YY in the message are code characters defined as follows:

XX= 01 = ZERO PAGE RAM FAILURE, check 6532

02 = (will not occur)

n3 = ROM FAILURE. Any number in the XX position ending with a 3 (for example, 23, 33, etc.) indicates a ROM failure. The first digit (2 and 3 in the previous example) points you to the appropriate chip that needs to be checked. The code for the any number ending with 3 in the XX position is as follows:

XX= Chip to Check

03 3A 13 4A 23 5A 33 6A 43 7A

Note: The message reflects the first bad chip it encounters, in numeric order. It is possible for chips following it to also be bad.

04 = INTERRUPT FAILURE, check 6532.

2? = FAULTY COMMUNICATIONS, Check 6520 at 9B.

Here is the code for the second two numbers in the YY position.

YY= 40 = Communication from Logic Board to Audio failed. Check 6520, both locations 8B and 9B.

80 = Communication to Logic Board from Audio failed. Check 6520, at locations 9B and especially 8B.

<0 = Communication between Logic and Audio failed. Check 6520, both locations 8B and 9B.

Also, the symbol <0 in both the XX and YY position, along with a hum or random notes and no beep after power on, may indicate a failure in 3A and/or 7A.

  • CONTROL AND COLOR DIAGNOSTIC TESTS

If desired, you may test all player controls and screen colors. To do so, activate either

Page 16

coin switch at power-up. The game then enters the Control/Color Test Mode. This mode lasts for seven minutes to give you time to test and make adjustments. After that, the Attract Mode begins.

In the Control/Color Test Mode, the screen shows this pattern:

The grid pattern tests your screen for any distortion or convergence.

The solid blocks of color (red, white, green, and blue) allow you to adjust the color. When any player control (player 1 start, player 2 start, or Fire) or coin switch (coin 1 or coin 2) is activated, its name appears below the white box. This shows that the switch connection is proper. When the joystick is activated, the message Joystick appears below the red box. Also, in the middle of the screen, a square indicates the joystick direction.

B. THE ATTRACT MODE

After PEPPER II goes through its automatic self-diagnostic test mode on power-up, a series of screen displays are shown repeatedly. One screen gives instructions to the player, another shows a brief demonstration of game play, and a third shows the High Score Table, reset to factory scores each time PEPPER II is powered up.

C. INTRODUCTION MODE

After depositing a coin, this message blinks on the screen while the Attract Mode

Page 17

continues:

PRESS PLAYER ONE START

If enough coins for two plays are deposited, this message appears:

PRESS ONE OR TWO PLAYER START

After one of the two play buttons are pressed, this message appears on the screen:

GET READY PLAYER 1

D. GAME PLAY MODE

Each play screen of PEPPER II is the side of acube. Four of the sides must be filled in to advance to the next level. To fill in a side, the player guides "Pepper" around an invisible floorplan. As Pepper travels, he leaves a track, resembling a zipper. Once he encloses a space or room, it fills in and points are awarded. The challenge and fun of PEPPER is to determine the size and shape of the rooms in the floor plan. Square markers, or posts, give clues. They mark the location of either a " or an intersection.

The floorplan is shown on Side 1 during the first cube to help the beginning player learn the play of the game more quickly.

  • Obstacles and Hazards

Pepper, the angel, must avoid two enemies: Roaming Eyes, and the pink ‘Zipper Ripper", who unzips all ‘freestanding’ lines (those not enclosing a room). Pepper's one defense is to enclose a room containing a pitchfork, which turns him into a devil for a few seconds. At that time he can go after all Roaming Eyes for points. At the same time, the Zipper Ripper freezes, but is still deadly.

If Pepper backtracks on a freestanding line, it unzips. The player soon learns to maneuver Pepper around on the lines enclosing rooms, to avoid losing freestanding lines to the Zipper Ripper.

The player goes to different sides of the cube by going out any of four exits, located in the middle of each side of the screen. When all four sides of the cube are filled in, a “Cube Bonus" is awarded, a new level is given, and a cube appears on the bottom of the screen,

  • Scoring

Points are made for enclosing a space (the larger the room, the more points earned), hitting a pair of roaming eyes, completing a side, and completing a cube. A bonus turn is awarded at the operator selectable score of 40,000, 50,000, 60,000 or 70,000.

E. VANITY MODE

Anytime a player's score exceeds one of the five current high scores, he is eligible to enter his initials in the Vanity Table. If both players of a two player game are record high scorers, the highest of the two is first invited to enter his initials. To do so, he directs a character through the alphabet with the joystick. Once on the letter desired, he hits either of the Start buttons. After either logging his initials, or after about 45 seconds, the game returns to the Attract Mode.

Page 18

APPENDIX A: SCHEMATICS

MEMORY MAP

Hex Address

FFFA-FFFF 8000-FFF9 52XX 5103 5101 5101

5100 5100 50CO 5080 5040 5000 4800-4F FF 4000-43 FF 0200-03F F 0100-01F F 0000-00F F Function or Device

Interrupt and Reset Vectors Program memory space Audio board communications Interrupt Condition Latch (read) Control Inputs Port (read) Output Control Latch (write) (Not used in PEPPER 11” upright) Moving Objects Image Latch (write) Option Dipswitch Port (read) Moving Object 2 Vertical Position Latch (write) Moving Object 2 Horizontal Position Latch (write) Moving Object 1 Vertical Position Latch (write) Moving Object 1 Horizontal Position Latch (write) Character Generator RAM Screen RAM Scratchpad RAM Stack RAM Zero Page RAM

Page 19

PAGE 1, GAME LOGIC PCB

  • Master Oscillator (1D)

From this oscillator all dynamic operations are derived, such as the processor clock, the main element and line counters, the shift register clocks, as well as all other forms of timing signals.

  • Element (Horizontal) Counters (1C, 1E, 2E)

These components form the final stages of horizontal timing. All operations in this game requiring horizontal positioning or timing have their origin here. Note that, beginning with signal HCLK (from Clock Divide Counter 2D), there are 256 counts prior to setting signal E256 high. When this signal goes high, it indicates that the horizontal blanking period is in progress. At this time the final counter (1E) is preloaded with a higher number than previously loaded. This creates a shorter count the second time around. The shorter count measures the retrace interval. When the retrace count is finished, the counter preloads with a lower number, establishing a longer count sequence again for ‘real time" sweep of the electron beam across the face of the CRT.

  • Line (Vertical) Counters (4F, 5F, 6E) These components form the entire vertical timing operation starting with a clock derived from horizontal timing. These counters count 256 times and then preload with a higher number, causing a shorter count the second time. This shorter count measures the vertical retrace interval.
Note that signal L256, when high, indicates vertical blanking is in progress. After the completion of the vertical retrace count, the counters once again preload with a lower number. This way they count 256 times during the sweep of the electron beam down the face of the CRT, allowing the horizontal timers to sweep one complete horizontal line for each count of the vertical counters. Thus, the electron beam reaches the bottom of the CRT, after completing 256 horizontal line sweeps. It then begins the vertical retrace count, and the whole cycle begins anew with the beam starting again at the top of the CRT.
  • Screen RAM Addresses (7D)

During the time the screen RAM is examined by the logic for output to the monitor screen, addresses must be applied to the screen RAM to count up at a rate

A-2 corresponding to the image cells conceptually arranged on the screen in a 32 x 32 matrix. The counts used here, 4 from the element counters, and 4 from the line counters, fulfill this timing requirement, The least significant element count used (E8) represents an interval exactly eight times that of one element. The least significant line count used represents an interval exactly eight times that of one horizontal line, or eight times a single line count. Dividing a 256 element line by 8

yields 32, and fikewise dividing a 256 Tine

vertical sweep by 8 yields 32. Thus the screen RAM address lines (RAM@& through RAM9) count at a rate that creates 32 horizontal counts and 32 vertical counts as the electron beam sweeps the face of the CRT. This makes 1024 conceptual "image cells* into which can then be _ inserted images of 8 elements by 8 lines. For more information concerning these images, refer to the text for pages 2 and 3 of the Logic Schematics.

  • Coin Input Decoding (1H) Some models of PEPPER II™ contain two separate coin inputs for special coinage applications. NOR gate 1H combines these separate inputs, making signal 5COINT, which sets the interrupt flip-flop (6— on page 8) when either coin input becomes active, thus forcing the microprocessor to jump to the interrupt service routine. This interrupt driven operation prevents ever missing a coin when inserted. However, this also means that when a game is first powered up, the coin input must be inactive. If for some reason the coin input switch is enabled at the time of power up, the game does not properly initialize until the switch is disabled.
  • Hardware Generated Line Positioning Proms (3E, 4E)

These PROMs are not used for PEPPER II".

  • Blanking and Video Clocking (5H)

Flip-flop 5H merely combines blanking and all other video.

  • Black and White Composite Video Output (1H)

This circuit is not used for PEPPER II™. If desired, however, these components may be installed to aid troubleshooting, by acting as a "video probe".

Page 20

al il “7 Ll a =3 ’ 9 , Al PR = eas

(case ome Tarouine cewasere> . en . LINE POSITIONING » :

ey ; qyeaeratee Black ¢ unite ComrosiTE vive out PUT,

coms Sat af melee a 4H - 502 GAME LOGIC PCR », ROPRER Ir . 44: .SYNC AND VIDEO SEWERAT)

Page 21

PAGE 2, GAME LOGIC PCB

  • Screen Controller PROM (6D)

This PROM controls the direction of data flow into and out of the screen RAM and character generator RAM. It prevents timing errors and buss conflicts, assuring that the microprocessor can write to either the screen or character generator RAM, or read back from either.

  • Screen RAM (7B, 8B)

The screen RAM is comprised of two 1024 x 4 static RAMs, configured to act as a single 1024 x 8 RAM. This creates a screen matrix of 32 horizontal by 32 vertical positions. A single byte code is stored in each of these positions to represent a particular character. During ‘real time" (the time the CRT is being swept by the electron beam) these character codes address the character generator RAM.

These character codes, when used as addresses, are combined with the three least significant line counts (L1, L2, L4) to present to the character generator output shift register all the necessary data to form an 8 element wide by 8 line high character on the CRT, located within one of the 1024 positions mentioned immediately above; that is, the 32 horizontal by 32 vertical positions.

The screen, then, is a storage place for single byte codes that call up an 8 x 8 character and place it into the corresponding character cell. This character is stored in the character generator RAM, shown on page 3 of the schematic.

  • Character Image Storage

Shown on this page are two PROMs (9c, 10C). They could be used as a permanent set of characters. However, PEPPER 1I1™ uses RAM instead, to increase the flexibility in character manipulation. This portion of RAM appears on page 3 of the Logic schematics.

  • PROM Power and Signal Selection (10B )

This Dip Shunt configures the logic for different types of PROM devices. For PEPPER 11", however, this Dip Shunt is unnecessary due to the fact that RAM has been used rather than PROM.

  • Character Generator Output Shift Register (12B)

Video from the character generator memory devices (RAM in the case of PEPPER I!™) is formed by this shift register as a byte of data that displays one line at a time from left to right on the CRT. This ultimately forms an 8 line high by 8 element wide character positioned on the screen according to the time it is presented to the shift register.

Output from this shift register are all the images seen on the screen except the player image and the player missile image.

Page 22

SCREEY GNP SeuseT and Buss DEECTION DECODING PROM 14014] essa ‘st reer S_ses80 ee

10 7S? fe seeeao” 220 soso “Sy TL 5 5 See" [2 Swe Te “3? [Screen RAM® wi 4 Gian, cove STFA) lz g 5°) [TESBO ew 1e{ soo)" SHE beam eS 30 ~~ vo7io as

10 _Ec6BD iseas

RAM 1S. o RAM Be fe RANT 17 ne 8_ihpoit_scouw

6116 ae

CHARACTER

GENERATOR WDE OUTPUT ISWET REGISTER

sesso amt ECCS BARC La la ry , ors z

uses i te nz ecoso tT |

seo Tal v7 1s Sige A

seas, te ccoso3],. [— CRARACTER WAGE STORAGE

SED eae FT a See faye 3 for a ey Alteraahe: RAM used fe peacean gored Clageable wager

Peon Pewee SIGNAL,

SELECTION

502 GAME LOGIC PCB Eg TE Ot

Page 23

PAGE 3, PLANE INTERFACE BOARD

Image Storage RAM

  • Character Generator Image Storage and Plane Interface Board (9C, U1)

These two RAMs, when used in_ this configuration, act as a 4096 x 8 bit RAM. The two color images placed on the screen are stored in this RAM by the microprocessor, according to the game Program. In this RAM images are established, altered, shifted slightly, and even replaced with a new set, if required by the program. When called by the logic to do so, the RAM presents, to the character generator shift register, a single byte, representing one line of a particular image. Each image is composed of 8 lines of data, each line is one byte-wide. Thus, 256 images of 8 x 8 bits can be stored here simultaneously and "called up" by the screen RAM to be displayed on the CRT in any of the 1024 character cell positions. A single byte code, stored in the screen RAM, calls up a character. The character may change or move by replacing the single byte code in the screen RAM, or by altering the data in the character generator RAM which forms the image.

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

PAGE 4, GAME LOGIC PCB

  • The 6502 Microprocessor (2A)

For detailed information concerning this microprocessor, refer to the MOSTEK publication, 6500-10A, MCS Microcomputer Family Hardware Manual.

One feature that should be mentioned here, however, is that this microprocessor has "memory-mapped 1/O*. This means that all ports interfacing to peripherals of any type must be located within the normal memory map, with no duplication of addresses, since no instructions are specifically oriented toward 1/0 operations.

  • Power-on Reset circuit (connected to 2A pin 40)

When power is first applied to a game, a particular sequence of events must occur to set up all logic conditions. If this sequence is broken for whatever reason, the microprocessor may become confused, and the game will not start and run.

This sequence is accomplished when the reset line to the microprocessor is the last line allowed to reach a ‘high" logic level. The Power-on reset circuit makes sure this occurs by utilizing the charge time of an RC network as a delay.

1f any kind of power interruption occurs during normal game play, the power-on reset circuit insures that the microprocessor is reset. This alleviates confusing the microprocessor, while it also recreates the original power-on sequence.

  • Processor Workspace RAM (4A, 5A)

The RAM, or workspace, consists of the lowest 1024 bytes of memory and can be divided into three separate sections due to distinctly different functions.

The lowest 256 bytes (0 to FF Hexadecimal) is reserved for special software register operations, and is called "zero page". The Processor uses this area to store dynamic variables. For details of this type of operation, refer to 6502 technical literature regarding "Zero Page Addressing".

The next higher 256 bytes (100 to 1F F Hex) is reserved for the 6502 stack. The processor stores return addresses in the stack when interrupted or called to execute a subroutine. The game program may also request the processor to store other kinds of information here for later retrieval.

The next higher 512 bytes (200 to 3FF Hex) are used as a scratchpad area. Miscellaneous calculations and their results are temporarily stored here.

  • Main Address Decoding (5C, 5D, 5E)

This circuit is the first stage of the address line decoding necessary to organize the memory map; that is, it places specific functions or devices within generalized blocks of the memory map, grouped by function,

For details on the addressing scheme, see MEMORY MAP, Figure 1.

Page 26

Bupasvaay soe eva seb 8" SER

2104] FE. 38-915 = 2d 31907 3Wyo 2059

“suoypowe> 249 WJ0 seep) “Ao sesodind sishyoun p 4304 484 p20 Bp epee): 310K 1-98 V24 FE 90Ud af abe Fe x] ots asa Hx vive sro a. eam ssoxrw nn 7 sec

saris SaIOTD CED 4 a> Shou sha aati = snroned = « Wa = be bzor se fag. awo6 says,

sant -— nat) ef ounes = ™ 08°

ane ws ssauaay [oom

  • Lc = er be yzal

avs-29S F ano *o4s2 39d

Seaniva sone)

Page 27

PAGE 5, GAME LOGIC PCB

  • Program Memory (6A through 13A)

These memory devices may be 2516, 2716 (5 volt only), or 2732 EPROMS. If 2516 or 2716 EPROMS are used, there will also be an additional memory expansion PCB in use to create more memory space. This PCB is simply an extension of the address, data and control lines present at the memory devices situated on the logic PCB.

Note that four of the lines to each memory device (PCSO through PCS7, PAP19, PAP20, PAP21) are programmable through jumper configurations located at 4B and 11B._ This allows different memory devices to be used and/or facilitates interconnection to the memory expansion PCB (if used).
  • PROM Address Selection (4B, 5B)

This is a second stage of address decoding, used to select each individual memory device when addressed. Signal ROMSEL (from page 4 Main Address Decoding) selects the Program Memory devices in general, and jumper 4B, together with decoder 5B further defines an address to a particular memory device.

  • Memory Device "Personality" Selection (11B)

The dip shunt, or jumpers block, alters control signal configuration to the program memory devices. This allows the use of alternate size EPROMS and/or those created by different manufacturers whose control signal pinouts may not be identical to one another.

Page 28

PROGRAM MEMORY

(CAL MANUAL For Procram Hs,

g 07 a9 07 ss fe oy

ROS oa ine

  • 2 73 is 3

Oe Roa 203, a2. ROO.

ROS 2 ro x Fo3 is 02 i for = RDO ro noe res 07 = 0 ne S3SS596

PrP eirs poss se DATA BUSS | TERMINATION.

paper 2

Ringing Suppression

:

H

gy Hi

q| i pera at papas at 4068 3P e80)

R06 RS roe, ROS mor Da. _ RDG ROS coy RO ROE. 0"

ms OD n RS AS = moe z col as 3

ROS abe esssaga

ROO Ree

pose ie ress a, paper et paper 2 Par20 20. fae 2020 bars 3 FAP is 19 PROM ADDRESS SeuecTION Configuration Shaww 15 MEWRY DEVICE PERSONALITY for BV ony 2732 EFROMS. Srikeriow SS gee ieee Configuration shown 15 EXIDY INC. watiy Featces CTE Le S32 reas, = a mht for otter 6502 GAME LOGIC PCB

cota deeee [fara rr]

Page 29

PAGE 6, GAME LOGIC PCB

  • Moving Object Horizontal Position (13F, 15F, 14F, 16F)

Counters 13F and 15F form a byte-wide counter which horizontally positions Moving Object 1 on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of the Horizontal Sync, they begin to count. The count outputs AND'ed through 15E give rise to signal M1HW, the Horizontal Position Window for Moving Object 1. Counters 14F and 16F are the equivalent circuit for Moving Object 2.

  • Moving Object Vertical Position Counters (16E, 12E, 1E, 13£)

Counters 16E and 12E form a byte-wide counter which positions Moving Object 1 vertically on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of Vertical sync, they begin counting. The four count outputs of the least significant of these two counters (M1L1, M1L2, M1L3, M1L4) are sent to the moving object image PROM to specify which line of the image is presently being displayed. The AND'ed outputs of the second counter give rise to signal M1VW, the Vertical Position Window for Moving Object 1. Counters 11E and 13E are the equivalent circuit for Moving Object 2.

  • "Write Moving Object" 16H, 5E, 3F)

Consists of two distinctly different functions. 6F and 16H form the circuit that generates the load pulses for the moving object position counters, while 5£& and 3F simply prevent the counters from counting during blanking.

  • Color Interface Output (16B)

This is a 14 pin DIP socket used as the connector interface to the color selection circuitry, located on the audio PCB. The signals and their functions are listed below:

Pin #

1 5SRLOAD = Shift Register Load Pulse (Neg. True)

2CBLB= Composite Blanking
3CSYNC= Composite Sync
45CVID= Composite Video (Neg. True)
55SCLK= Shift Register Clock (Neg. True)
6HSYNC= Horizontal Sync

7 GND

8VSYNC= Vertical Sync

9 5MO2VID = Moving Object 2 Video (Neg. True)

105MO1VIDMoving Object 1 Video (Neg. True)
WDBDIR= Character Generator Address Line 9
12CSSR= NOT USED ON PEPPER II

13 VD7A10 = Character Generator Address Line 10 +5V

Page 30

inoue OesecrS VARSE crak hee We bearer L wre aescer 2)

beet eeaigrse mw D7 fer more ie nevi sie a1

tone coef Lime posre tse eww Ewin al 6 sowot mmo a [ts0o) jon:

Nevo 0 vo 3} [were oBrecrs G502 GAME LOGIE PCB Se EZ novin OBseCT VIDEO GENERA

TOF

Page 31

PAGE 7, GAME LOGIC PCB

  • Moving Object Multiplexing (14A, 14E) vole Be These two multiplexers pass information to the moving objects image PROM. They contain two codes: one determines which image should appear, and the other specifies which line of that image is to be displayed.

The data passed alternates between data for Moving Object 1 and Moving Object 2, depending on the state of element count E32,

The upper multiplexer (14A) passes the “which image" code, and the lower multiplexer (14E) passes the ‘which line of that image" code.

  • Moving Objects Image PROM (11D)

This EPROM accepts as an address the image and line codes of moving objects 1 and 2 (see “Moving Object Multiplexing" above). It then presents the appropriate data for one line of the image to the output shift registers,

The timing of the logic insures that the correct pair of shift registers are loaded with the data, then shifted out at the correct time to become, one line at a time, the 16 lines of video for that character (Moving Object 1 or 2).

  • Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D)

Shift registers 12D and 13D together form a 16 bit shift register whose task is to accent, as data, 16 bits (2 bytes) representing a single line of the image for Moving Object 1, then shift these 16 parallel bits out serially to become video. This operation is repeated for 16 consecutive lines, resulting in a video image that is 16 bits wide by 16 lines high on the monitor screen. Shift registers 14D and 15D together form this same type of circuit, identical in function, for Moving Object 2.

  • Moving Objects Shift Register Load Logic (2F, 16H)

This circuit sends properly timed load signals to the Moving Object Video Shift Registers. These load signals are needed to load the image data into the shift registers at locations 12D, 13D, 14D, and 15D.

  • Moving Object Shift Register Control Logic (15H, 14H)

The input signals to the upper two gates (15H) represent horizontal and vertical position ‘windows" for the two moving objects (for example, M1HW = Moving Object 1 Horizontal Window, M2VW = Moving Object 2 Vertical Window). These windows allow the Moving Object shift registers to shift only at the right time. This insures the image is generated at the correct position on the screen,

The lower 2 gates of 15H are, in PEPPER ul, used for later decoding in the color selection circuitry, located on the audio PCB.

Device

  • Memory Personality Configuration (10D)

This is another Dip Shunt which reconfigures the PC board in order to use an EPROM (11D) of another type or manufacturer.

Page 32

[Tege00-3

soy 51589 Save __2089

Page 33

AUDIO/COLOR PCB-GENERAL DESCRIPTION

The Audio/Color PCB is so named because it contains not only the circuitry required to generate all sounds, but also the color selection decoding circuitry and video output connector.

This PCB contains a dedicated 6502 microprocessor and circuitry to support the simultaneous generation of many types of sound, including three channel music. The Logic PCB simply sends commands to the Audio/Color PCB via a bi-directional communications port and the Audio/Color PCB takes it from there. In some cases this PCB even aids the Logic PCB in some of it's calculations when there is not enough processing time available on the Logic PCB.

As a result of this structure, the actual program to generate sounds or music resides on the Audio/Color PCB. There is also a handshake required between the two PCB's in order for the system to power up correctly, and of course, there is no video output without the Audio/Color PCB connected.

Page 34

PAGE 1 OF 5, AUDIO/COLOR PCB

  • Logic and Power Interface (P5,J2,J3)

Connector P5 provides the audio/color PCB with all the power it requires to operate. Also fed through this connector are the two speaker output leads. P5 interfaces only to the power supply module and the speaker, through the main harness.

Connectors J2 and J3 are the most significant path of communication between the Logic and Audio/Color PCB's. Address lines, Bi-directional Data lines, processor control lines, and the Audio/Color PCB Select line are all passed through these two connectors. (9B,13D)

  • Communications and Address Decoding

Peripheral Interface Adapter (PIA) 9B, in concert with 8B (another PIA ,shown on page two) serves as a_ bi-directional communications path between the Logic PCB and the Audio/Color PCB. During information transfer between the two PCB's, both PIA's are in use. Information from the Logic PCB microprocessor passes through the PIA at 9B to the PIA at 8B, then to the microprocessor on the Audio/Color PCB. When information is passed the other direction, the path is the same, but the direction is reversed.

During the time that no information transfer is occurring between the two PCB's, both microprocessors can continue to operate independently.

Also shown on page one is 13D, a 3-line to 8line decoder, used to generate the write signals for the Color Data Latches. These Latches will be covered in the text for page five of the Audio/Color PCB.

Page 35

zs

wysowd — LyWans a Bd yoOP/sGcy Taw cd aw ed "OY iv Bae

“77 B30 KINI yoy pms" ssHAAe soveyioasin Rt 38 SeOaIIND TY TES" LIN Say HOISTS TW

FBLON T ‘eh oa

Faia navi Sh.

mv] f va car}? car] Coc ia oa = amr] Ey z Sr

Sa a awe 2907 on Ea aio 9997 Oi rg ean ioe

Page 36

PAGE 2 OF 5: AUDIO/COLOR PCB

1, 6502 Microprocessor (3B)

This microprocessor is the same as that used on the Logic PCB, but is exclusively dedicated to the generation of sound It can communicate with the Logic PCB microprocessor, and receives it's instructions thereby. Once it has received it's instructions, however, it asserts complete control over all Audio/Color PCB circuitry and ignores the Logic PCB microprocessor until such time as it is informed that another command is ready. Some commands are of a type that must be processed immediately, irregardless of other operations in progress, and some commands can wait until the operations in progress are completed. The program on the Audio/- Color PCB handles all these eventualities appropriately.

  • Peripheral Interface Adapters (8B, 7B)

The PIA at 8B, as mentioned in the text for page one, is used in_ bi-directional communications between the microprocessors on the Logic PCB and the Audio/Color PCB.

The PIA at 7B is used for two fundamental purposes on this PCB. The first, and most

important, is that it contains the RAM that the microprocessor uses for zero page and stack operations. The PIA only contains 128 bytes of RAM, which under normal circumstances would not be sufficient for both zero page and stack. In this case, however, the memory map on this PCB has been altered, so that when the microprocessor thinks it is putting the stack at address O01FFH it is actually putting it at address 007FH.

The second use of this device is that of a programmable interval timer, used for various purposes unique to the specific sounds being generated on this game. The ability of this device to generate interrupts at time out is utilized here.

  • Address Decoding (4B)

Keyboard Encoder (4B) is used here to generate the chip selects of all devices located in the memory map of the Audio/Color PCB.

  • Music Generator (2B)

Another Programmable Counter/Timer device is used here to generate music (and sometimes other special effects) in up to three channels (or voices) simultaneously. The music is created by a special software operating system, and all but the counter/timer chip is therefore invisible.

  • Master Oscillator (A1,B1)

This oscillator is the source of all timing on the Audio/Color PCB. If this clock stops running, so does everything else on the Audio/Color PCB. It is, however, completely independent of the clock and other timing signals generated by the Master Oscillator located on the Logic PCB.

  • Program Memory (3A,4A,5A,6A,7A)

The memory devices used here are 2716 (2048 x 8) EPROMS. The DIP shunt located at 8A is used to reconfigure the control and power supply lines, if necessary, for equivalent devices from different manufacturers, whose pinouts may not be the same.

  • Output Filter Latch (1C)

This latch is used simply to switch different output filter capacitors in or out of the circuit to soften or shade the sound, according to program requirements, or to change the volume.

Page 37

PROGRAM MEMORY

SA 7A

AODIO/coLoR, eB. LiRgeA 77-0007-0!

Page 38

PAGE 3 OF 5: AUDIO/COLOR PCB

  • Clock Manipulation and Noise Generation Circuit (3D,4D,6D,5E)

The timers inside Programmable Timer Module 3D can be incremented or decremented either internally by the Phase Two clock input, or externally from the "C* inputs (C1,C2,C3). Both options are used by the program. When the counters are being controlled by the Phase Two clock, the "C" inputs have no effect, and the noise generation circuit is therefore inoperative. In order to generate sounds that are classified as noise, or contain some kind of noise within them, the counters are Programmed to decrement in accordance with the input on the "C* inputs. While in this mode, the combination of 6D (Dual "D* Flip-Flop) and 5E (128 Bit Shift Register), are used to "randomize" the clock inputs to the Programmable Timer Module (3D). The “randomizer" can be clocked with either the Phase Two clock or counter output Q1.

  • Amplitude Modulation Control (2D, 7D, 8b, 9D), Counter (3D) outputs Q1,Q2, and Q3 are already highly complex sounds, but in order to create much more specialized audio they must be modulated in amplitude. Each channel is separately controllable in amplitude by associated Digital-to-Analog converters comprised of analog multiplexers and a resistive ladder network. Three control bits on each multiplexer select a voltage to output, according to which input pin is addressed (since each input pin is tied to a different point, and therefore voltage, in the resistive ladder). The voltage thus selected is applied to one of the two inputs to each segment of 2D (another triple analog switch). The other input is tied to ground. Note that the control bit to each analog switch segment is one of the previously mentioned count outputs (Q1,Q2,Q3). In this manner, each output can be controlled for frequency and amplitude individually.
Note also that the count output from Q1, unlike Q2 and Q3, first passes through yet another analog switch whose function is to turn off the count output of Q1 prior to reaching the Digital-to-Analog conversion stage. This is done because the Q1 output is the one used for selective clock frequency generation, and would therefore interfere with other sounds if not disabled at the appropriate time.
  • Output Summation and Special Effects Volume Control (2E)

The three segments of Operational Amplifier 2E are configured as voltage followers (for impedance considerations), and their outputs are summed together at the top of a 10K POT, R31. The output volume, therefore is determined by the voltage applied at each input and the adjustment of the POT. Note that the resistors used to sum these three outputs together are large in value, so that each channel will have minimal effect on the others when conflicting signals arrive simultaneously (except, of course, that their sum will appear at the output).

This summed output is then again summed with all other sounds generated by this PCB at the input to the final Power Amplifier.

Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

PAGE 4 OF 5: AUDIO/COLOR PCB

  • Summing Amplifier and Master Volume Control (3F, R46)

One segment of Operational Amplifier 3F is used here as a point at which all the various sounds generated on this PCB are brought together. Note that the output goes immediately to a 10K POT (R46) which has ground on the other end. The wiper, therefore, varies the final output volume of all sounds together.

  • Integrator and Audio Power Amplifier (3F,10F)

Another segment of Operational Amplifier 3F is used here as an integrator; that is, it is used to "roll off" the higher frequency sounds in order to prevent the power amplifier from going into unwanted oscillation.

A-14 The Audio Power Amplifier (10F) is a Dual Audio Amplifier IC configured as a "Bridge Amplifier" and may be either a LM377 or LM378 for Revision A, Audio/Color PCB. Revision letters are located at position 11C. In later versions of PEPPER II it may possibly use a LM379 with a reconfigured DIP shunt. Information regarding this is available in the operators manual for this game, or contact the Exidy Customer Service Department for assistance if you must use an alternate device.

Volume Controls

Master Volume R46, see the fourth page of Audio/Color PCB schematics.

Music Volume R9, see the fourth page of Audio/Color PCB schematics.

Special Effects Volume R3, see the fourth page of Audio/Color PCB schematics.

Page 41

°

DIP SHUNT. CONFIGURATION

rT l<

wan aur) pe a noe Lin's cua AUDIO/COLOR PCB m4 —" D | “GEG Besem oC _ 17-0007-01 6 ] 5 4 | 3 2 ] 1

"HEAL & ZOOK [tert vow SrRVER

Page 42

PAGE 5 OF 5: AUDIO/COLOR PCB

  • Pattern (10A,9A) Character Color Division

The two segments of Flip-Flop 10A, using the upper two address lines from the character generator circuit, divide the character generator RAM space into four (4) conceptual groups (or quadrants) according to address. This is done in order to assign different colors to different characters.

Using this method, any character stored in a particular quadrant will be the same color as any other character stored in that same quadrant. If the same character is stored in a different quadrant, it will be displayed with a different color. The output of 9A (Two-line to Four-line decoder) applies the separated video lines of these quadrants to priority encoder 10B, whose task is to determine which image is to take visual preference when two or more coincide on the TV screen; that is, which image is to appear to be in the "foreground", and which is to appear to be in the "background".

  • Priority Encoder (10B)

All the video signals generated by the logic PCB are applied to the priority encoder. The signals assigned the higher priority are shown at the top, and the lower priority are shown on the bottom. The output of this device is a 3 Bit code representing the highest priority video line active at that instant. This output code is then sent to the color multiplexers as an address which will select the appropriate color for the imagery generated on that video line. Note that the lowest priority input to the encoder is tied permanently low (active). This insures that when no other video is being generated, there is a background color present, unless of course, the program has selected a background color of black at that time.

  • Color Data Latches (11C,12C,13C)

These latches are addressed directly by the Logic PCB microprocessor. Here the microprocessor stores the data that determines which character is what color. This data is then passed to the color selection multiplexers.

  • Color Selection Multiplexers (11B, 12B, 13B)

Each of the three multiplexers controls the video output to a different color gun in the CRT. One turns the red gun on or off, one turns the green gun on or off, and the third does the same for the blue gun. The output combination of the three multiplexers provides for one of eight possible colors to be displayed at any given instant. The color displayed is determined by two things: what type of video is present (e.g. which character), and what color the microprocessor has currently assigned to that type of video. As mentioned above, the color assignations are stored in the color data latches. The priority encoder (10B) issues the code representing the type of video currently displayed. Using these two pieces of information, the multiplexers look at the appropriate bits in the color latches and send the data directly to the TV to turn the color guns on or off.

  • Video and Sync Signal Polarity Selection (11A,12A)

Before being reclocked one last time, all video outputs are passed through an Exclusive-Or gate (11A), so that one input of each segment can be used to invert the video (make it 180 degrees out of phase with respect to the input to the gate). This feature insures compatibility with TV monitors made by several different manufacturers.

The TV Sync signals are also routed through Exclusive-Or gate segments (12A) for the same purpose.

  • Final Video Output Re-synchronization (13A)

To insure that all video signals and sync signals are accurately synchronized in time, they are all re-clocked one last time together by a HEX "D'Flip-Flop. It "cleans up" any spurious irregularities or propagation delays that may have crept into any of the video or sync signals.

Page 43

RED DATA LATCH COLOR SELECTION

+20 8 5 la Pht Dip SockeT CoRWECTOR . VIDED PoLaRITY vio" cur FoR Tete

[ere 7} ‘Sme2vid. SMaqvID, vivy sv. ‘VDTAIO +5VDC, anew vNar® ‘SINC POLARITY “snc! cur ror fare SCSYNC astwe tS Hswca 2A vewne__—1)) vse sven

PRTTERA) CHARACTER COLOR DIVISION weco PRIORITY ENCODER pera 7 PRIS RIO P21 10 PA WAFER HEADER

ep owe pi ‘GRN OT pS Bu our ‘esviic_aor- oureur To HSYNC_ OUT! TV moNrToR svc” OUT” Creu mains

HARNESS )

"ABO /Lok PCB ScHEMRTIC. DIAGRAM

Page 44

Jl Yocic soaro yer Down oad FRE ‘SPARE

SPARE

‘SPARE

Sx gu etn) 04 ( oz

ounen-|

Swat BHT ae | am ‘ONE FLAVER_CTART e2aa310 | VeuTORE =0$ spare

‘A/D CONVERT M2

J201 MONTOR vi0Eo r/o y/o.

GY/GRN Gyjaw RN] WHT

PED RN eu HeyNc vsyne ene con au, ‘SwAY_U wit Reb CRN war LEFT wT VIO, 2 PLAYER START CRN TEL BLU/ORN ORNL SIUCTS Sw.BUF. 05 SW.BUF. 03 4n) SW-BUF.D1 DN) SPae anTi= 50M + 12v 0) “$y Pane, +5 voy +5y sy

com 2 input AD Mi

[en=aue

SPARE. Sane ow v sync HsyNc su DATA RN OATA RED DATA reo RED. RN = an/wat

cr Jw RED Creu

ey can mu / wer Gr/Re. er

=NUOTIBO OS N«xecc 4m vzErrcrnmocerhd PRG aaRen

vai Avdi6 coLor can can ee TEL 7 FICE ~via | PORveK rs

ra

ve even vic ax [Ont Bux ‘ORN om

or ey Jae aul J? P10 BOARD pecuLaTOR

‘BOARD

-12vi0)] 5

wav(n| 2 sian) “sv +120)

‘Ajo Nt SPARES |. POLARIZING KEY J1 BETWEEN

PINS 86 puamstart] 7.

WIRING DIAGRAM MAIN HARNESS

Page 45

JOYSTICK

g

Dow No $3 P SHU} SL} Sil

WO sq {=]

ONE CWE START Siay downs Bu Ler Buy ve Bun eer c wo Plve sraer Alp mi ajo m2 +5v +50 Guo

>| so one praveR 7 4 cover we LS SHRI WERE com WIRING DIAGEAM- CP HARNESS ] 3 2

Page 46

REVISED PER ECN (00235

ery

DO NOT SCALE DRAWING IN MICROFARADS +12V (HI)

1, ALL CAPACITOR VALUES ARE

IDWIVERSAL POWER SUPPLY |r ELECTRICAL SCHEMATIC, ZA SHOWN FOR REFERENCE ONLY +12V (LO) —12V (LO) —l2V (HI) eo

Page 47

NEXT ASSY TED On buasescio |venroRe (xnv)2 NIOD

WOOD ON WOD ON

LHM/118 NYo/Mma

ra] a3 ie Coes W3LNNO0D NiO *xny gs HOLIMS WY1S

Y3LNNOD NIOO

WIRING. OlaGi ET DIAGRAM - UNIV. COIN DOOR HARNESS | |_| esi =r 71-2449 10 B DO NOT SCALE DRAWING

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

{ " COLOR GAME MONITOR SCHEMATIC

eu seer 9401 Q.402 0403 RED OUT GREEN OUT BLUE Gur

DIAGRAM

se, REY 352 a70P pire) HOR.OUT. 280869 2e0e068

16301 SYNC AMP vosc 1.0! wala23

DEGAUSSIG COIL,

WELLS GARDNER

K4901B, K4906B, K4951B 5833

K4956

Page 50

PART Ill: ILLUSTRATED PARTS LIST FOR PEPPER II”

The following is an illustrated parts list to aid you, should you ever need to order new parts for PEPPER II™. The drawings have all parts labeled by a number within a circle. This number refers to the item number on the Parts List directly across from the drawing. In the case of the Final Assembly list, the second drawing has numbers referring to the Final Assembly list found opposite the first drawing.

Following the Illustrated Parts List is a list of parts for the Logic, Audio and Plane Interface boards.

Page 51

A. PEPPER 11™ FINAL ASSEMBLY

Item Part Number Description

D38-5137-10 Assy, Cabinet D90-0002-00 Assy, Control Panel C38-5148-10 Assy, monitor D38-5134-10 Assy, Universal Power Supply C38-5136-10 Assy, Isolation transformer D96-0136-10 Assy, Coin Door 25 cents D96-0136-11 Assy, Coin Door D96-0136-12 Assy, Coin Door D96-0136-13 Assy, Coin Door 10 D96-0136-14 Assy, Coin Door aa D38-5135-10 Assy, Flourescent Light

1290-0005-00Assy, Logic and Audio Color Board

13 C76-1225-20 Assy, Door 14 E71-2443-10 Assy, Main Harness

1571-2250-10Assy, Isolation Transformer Harness

16 C71-2442-10 Assy, Speaker Harness 17 C38-5133-10 Assy, Power Cord 18 C71-2440-10 Ground Cable 19 B68-0035-11 Oblong Speaker Grille 20 B68-0131-10 lamp Bracket 21 C80-0003-00 Logo Plex 22 C75-5185-11 Ambient shield 23 C80-0002-00 Display Plex 24 C68-6050-20 Coin box lid 25 C68-0124-10 Mounting Bracket, Logo Plex Panel 26 B68-0142-10 Hasp, Coin Box 27 C68-0141-10 Interlock Switch Bracket 28 B89-1008-10 Label, Serial No 29 B89-1019-10 Label, Fuse 30 B89-1020-10 Label, Voltage, 110V 31 B89-1021-10 Label, Voltage, 220V

3280-0004-00Decal, Side art, left
3380-0005-00Decal, Side art, right

CONAUAWNA

3470-6053Light, Flourescent bulb
3572-3000Switch, Interlock
3668-6050-10Coin Box, Universal
3774-6524#10-24 x 1 1/2" large carriage black
3874-8532#10-32 x 1° Ig. soc. button head black
3974-4601#8 x 5/8" Ig. pan hd, x-recessed type AB
4074-4606#8 x 1" Ig. flat head x-recessed type AB
4174-5464#8 x 1/2" Ig, sheet metal, type AB, pan head, square drive, Black
4274-8534#10-24 x 2" Ig. hex hd. mach
4374-8544#10-24 x 1° Ig, carriage, BIk
4474-5468#10 fender washer, 1/38" ID x 1 1/4°0D
4574-6513#10-32 kep nut
4674-6506#10-24 kep nut
4763-7061speaker
4888-4002small tywrap, 4" minature
4987-1001packing list envelope
5087-1062plastic bag, 10" x 12"
i00-0001-00Pepper Op and Service Manual
5333-5040TV Manual, Wells-CGardner #19K 4605
5489-1009-10FCC Warning Label
5574-4603#8 X 3/4" Ig, pan hd, x-rec, type AB zinc pit
5675-5198Retainer clip (flour.)
5774-8549#10-24 x 1 1/4, carriage bolt black
5889-1023-10Static Display
5982-1019-10Seal, Strain Relief Plate
6036-0006-00Plane Interface Ribbon Cable Assy
6136-0005-00Plane Interface Ribbon Cable Assy
6277-0006-00PCB Plane Interface
6351-6047-01#6 3/4", wood screw
6458-6070-65spacer, nylon 1/8" Ig
6555-6000-01washer #6 flat B-2
Page 52

Ges ee AimReH Cons Doow Ee ) 1B msioe of Com Dooe Axee ays iw Gud See.

Page 53

L | z & v = s 9 Z \

Saaese =] Tere asaiy Tec —_ ai One oO, Ae ‘03) @ @- i 5 2 5

\ @)

& 1 I z | € ’ a $ 9 zZ

Page 54

B. CONTROL PANEL ASSEMBLY 90-0002-00

Item Part Number

65-0001-00 80-0001-00 90-0001-01 B68-0140-10 94-0001-00 74-0203 72-3062-11 72-3061-11 10-74-5247 11 53-0042-01 12 74-8548 WON NAWNHA

European Version: 90-0001-02 94-0002-00 Description

CONTROL PANEL FAB POLYCARBONATE OVERLAY JOYSTICK ASSY LATCH BRACKET CONTROL PANEL HARNESS ASSY PAL-NUT PUSH BUTTON SWITCH ASSY 10-24 X 5/8" CARRIAGE BOLT, BLK.ZN 10-24 NYLOCK NUT #6-32 X 3/8" LARGE FLAT HEAD, X-REC., MACHINE ZINC PLATE

JOYSTICK ASSY CONTROL PANEL HARNESS ASSEMBLY

Page 55

ens (20n) Gen (er) wht fos PO eke ine Side BE wimta) 9 6 Te CaNrtne fe Bevis’ “Pest MAT aE ES “cote EEE. BS Wee ecrtire, tune BE Coane t eee

Page 56

C. JOYSTICK (90-0001-00)

(Part Numbers included on drawing, opposite this page)

Page 57

G3IsIOIdS ISIMYSHLO SSIINN S3LON uO VA? OBE NoUdtw9s30 WaSWNN LuVd FOUS AOL ie ob

LHD HOLIVIS OPIUM Bas

-LG09-25] OH MY Hy VAL FBS (VBRIS

(wesdorea) 208 v(E)Ol DeLIIWW GRCOW- HBLITSOPMUW OO £10$-9p Aang wouawesa r ‘SNOISIAaH OPN? HQUINS GFW

Page 58

D. UNIVERSAL POWER SUPPLY ASSEMBLY, 90-0006-00

Item Part Number Description

1 C76-1258-10 POWER SUPPLY MOUNTING BOARD

274-3503SCREW, PAN HD, #6 X 1/2" LG. TYPE AB
374-2516SPACER, #6 x «125 NON-METALLIC
474-5198SCREW, PAN HD. #6-32 x 3/4" LG.
574-3500WASHER, FLAT, #6
674-3502NUT, KEP, #6-32
778-3001POWER SUPPLY, 5V @ 6.0 AMPS
863-4028TRANSFORMER, FILAMENT, 24V @ 4.0 AMPS
977-0009~-05PRINTED CIRCUIT ASSEMBLY UNIVERSAL POWER SUPPLY

10 C71-2389-10 HARNESS, POWER SUPPLY 1 C71-2446-10 HARNESS, POWER SUPPLY FLOURESCENT

1280-40041/4" SHRINK TUBING
1388-4002TYRAP
Page 59

oa

©

FOR PARTS LIST SEE 77-3365- 15. “O1SaG 434 SIT LNANOdWOO “ON W3LI

a. APPLY HEAT TRANSFER COMPOUND TO ITEMS 7 THRU i NOTES UNLESS OTHERWISE SPECIFIED:

‘promcch 390 Java DA eae fama 77-3365-15 SUNNYVALE Ca e403, 408-734-9410 ¥ eae Sear eine DO NOT SCALE DRAWING

Page 60

E.

Item Part Number

CONauswna 63-4029 B76-1259-10 74-5463 74-5468 74-6402 74-6506 61-8058 61-8055 61-8357

74-8536 61-8072 61-8054 ISOLATION TRANSFORMER ASSEMBLY, C38-5136-10

Description

TRANSFORMER, 1 SOLATION BOARD MTG. TRANS SCREW, PAN HD. #10-24 X 1.00" LG WASHER, FENDER, #10 WASHER, FLAT, #10 NUT, KEP, #10-24 3 PIN MOLEX PLUG FEMALE MOLEX PINS 2 PIN MOLEX RECEPTACLE WIRE, COPPER, STRANDED #18 AWG TERMINAL, RING #10 STUD SPLICE, BUTT MALE MOLEX PIN

Page 61

aoa JSMWaHIO SSTINN SIONVEETOL

(xe) (a= wad aasinayy 9

“YIEBWOV W231) IST Sldvd &SSd WAWYOR SNOWING Ov2001 NPA Bd Aasinayl SOY CYOILNI0S) OL SY3IFY

FOR PARTS LIST 38-5136-XX NOTES UNLESS OTHERWISE SPECIFIED: pmensen"" TRANSFORMER ASSY, ISOLATION lor 38-5136-XX 390 JAVA DR Peat TOLERANCES: CA94086 408-734-9410 FRAcrons fancies» —e— aRORRIETARY ( Serecvumansrigas'| gesenonans., DO NOT SCALE DRAWING UT WATER ADHORESTON,

Page 62

F. COIN DOOR ASSEMBLY, 90-0003-00

Item Part Number Description

166-4003COIN DOOR, DOUBLE (VENDALL)

2 D71-2444-10 UNIVERSAL COIN HARNESS ASSEMBLY

374-3502NUT-KEP #6-32
466-4002COIN ACCEPTOR, 25 CENTS
595-0002-00STRING CUTTER (VENDAL DE-1-S)
Page 63

ee: |EVISED PER ECA) 100221

° BLU/oRN ~ @nl'a) pb | COIN DOOR aAssy.- |, VT | 96-0136-10 3 2 1

Page 64

G. LOGIC AND AUDIO BOARD ASSEMBLY 90-0005-00

177-0008-05PWA LOGIC
277-0007 -05PWA AUDIO COLOR
374-8552SPACER NON-METALLIC #6-32 X 7/8 LONG
474-5182SCREW, PAN HD. PHIL #6-32 x 1/4 LG
571-2439-10CABLE ASSY, RIBBON
674-5173WASHER, FLAT, NYLON #6
Page 65

H. PRINTED CIRCUIT ASSEMBLY-UNIVERSAL POWER SUPPLY, 77-0009-05

77-0009-04 13-4085-00 13-3364-00 13-6844-0 20-0003-00 20-0005-00 21-0003-00 21-0004-00 21-0005-00 10 21-0006-00 W 84-0012-00 12 84-0013-00 13 40-0002-00 14 50-4027-00 15 53-4011-01 16 37-0001-00 WONAUEWN| UNIVERSAL POWER SUPPLY BOARD CAP, ELECT. 4000MF, 50V AXIAL LEAD CAP, ELECT. DIP 33MF 25V + 20% CAP, ELECT. DIP 6.8MF 25V + 20% DIODE 60S1 or UT4010 RECTIFIER, BRIDGE MDA-970-1 TRANSISTOR, 2N3055 TRANSISTOR, 2N6246 REGULATOR 7905 REGULATOR 7912 HEATS INK HEATSINK CONNECTOR 12 PIN (WAFER HEADER) SCREW, PAN HD #4-40 x 3/8 LG (PHIL) NUT, KEP #4-40 TYRAP 5 1/2"

Page 66

1, LOGIC BOARD, 77-0008-05

|tem Part Number Description

177-0008-04PCB LOGIC
222-0001-021.C. 74LS00
322-0002-021.C. 74LS02
422-0003-021.C. 74LS04
522-0004-001.C. 7407
622-0005-021.C. 74LS08
722-0006-021.C. 741511
822-0007-021.C. 741520
922-0008-021.C. 74LS21
1022-0009-021.C. 74LS27
1122-0010-021.C. 74LS32
1222-0011-021.C. 74LS74
1322-0012-021.C. 74LS112
1422-0013-021.C. 74LS138
1522-0014-021.C. 74LS139
1622-0015-021.C. 74L8157
1722-0016-021.C. 74LS161
1822-0017-021.C. 74LS166
1922-0018-021.C. 7415193
2022-0019-021.C. 74LS241
2122-0020-021.C. 7415245
2222-0021-021.C. 7418374

23 25-0004-00 24 23-0021-00 25 24-0011-00 MICROPROCESSOR 6502 2114 RAM (1K x 4) 6301 PROM (256x4) P2L5C-1

2624-0012-006331 PROM (32x8)

P2L6D-1

2724-0013-006331 PROM (32x8)

HRL14H-1

2820-0001-011N4002 DIODE

29 02-4712-00 30 02-1222-00 31 02-1822-00 32 02-2222-00 33 02-2722-00 34 09-2212-00 10 Pin Sip 35 09-0004-00 10 Pin Sip 36 09-4722-00 10 Pin Sip 37 09-6822-00 10 Pin Sip RES. 470 OHM 1/4W 5% RES. 1.2K 1/4W 5% RES. 1.8K 1/4W 5% RES. 2.2K 1/4W 5% RES. 2.7K 1/4W 5% RES. 220 OHM 1/8W 5%

RES. 2.2K 1/8W 5%

RES. 4.7K 1/8W 5%

RES. 6.8K 1/8W 5%

3823-0045-00CAP. .Otuf CERAMIC

DISC 39 10-1034-1 DISC CAP. .1uf CERAMIC Location

3D, 15C, 15H 1H, 6H, 8F 1D, 4D, 3F, 10F, 11F 2c 5E 3H 2F 12F, 15E 7F, 2H 6F 1c 2E, 6E 5B, 5D 7E, 16H 14A, 14E 1E, 2D, 4F, 5F 12B, 12D, 13D, 14D, 15D 10E, 12E, 13F, 15F, 147M 16F, 11£ 13E 1A, 3A, 15A, 3B, 6B, 9B, 8C, 7D, 9E, 4H 3C, 4C, 6C, 13B, 15B 1F, 14B, 7C, 9D, 8E 2A 4A, 5A, 7B, 8B, 11C, 12C, 13C, 14C 5C

6D

14H

8E, 9F, 2H 1D, 2H 2c 1C, 2C 7E, 2A IC, 2C 9E

15A

14A

1D

A/R

Page 67

I. LOGIC BOARD, continued

‘litem Part Number

10-1044-1 13-6844-1

13-3365-0

13-4775-0

47-0001-00 49-5002-00

29-0001-00 40-0061-00

44-1601-00

44-2401-00

44-4001-00

44-1401-00

44-1801-00 11-1053-00 02-2212-00 02-1802-00

10-2214-4 Description

CAP. 6.8uf 25v DIPTANT CAP. 33uf 25V ELECTROLYTIC CAP. 470uf 10V ELECTROLYTIC DIPSHUNT JUMPER PAKS 16 PIN DIP SWITCH 8 POS. CRYSTAL 11.289mhz (SERIES) 10 PIN MALE MOLEX HDR DIP SOCKETS 16 PIN LOW PROFILE DIP SOCKETS 24 PIN LOW PROFILE DIP SOCKETS 40 PIN LOW PROFILE DIP SOCKETS 14 PIN LOW PROFILE DIP SOCKETS 18 PIN LOW PROFLE CAP 1uf DIPTANT RES. 220 OFM 1/4W 5% RES. 18 OHM 1/4W 5% CAP. 330 pf CER. DISC E PROM, 2732 P2L6A-1 E PROM, 2732 P2L7A-1 E PROM, 2732 P2L8A-1 E PROM, 2732 P2L9A-1 Location

1C, 15D, 6E, 13F 1C, 2C

10H

4B, 11B, 10D

16A 1D

16C, 16F 4B, 11B, 5C, 6D 14H, 10D 6A thru 13A, 11D

2A

16B

4A, 5A, 7B, 8B, 11C 42C, 13C, 14C C45 thru C52, 5D, 2H R200, R311 R300 thru R302 5D 6A 7A 8A 9A CAP 220 pf CERAMIC DISC

  • PROM, 2732 P2L10A-1 £ PROM, 2732 P2L11A-1 E PROM, 2732 P2L12A-1
  • PROM, 2716 P2L11D-1

J. AUDIO/COLOR BOARD ASSEMBLY 77-0007-05

BACOVaurwna 77-0007 -04 22-0013-02 26-0003-00 25-0002-00 25-0004-00 27-0001-00 22-0022-02 27-0002-00 22-0023-00 22-0055-00 PRINTED CIRCUIT BOARD 1.C. 7415138 1.C. 6520 1.C. 6532 1.C. 6502 1.C. 6840 1.C. 74LS154 1.C. 8253 1.C. 4069 1.C. 4013B 10A 11A 12A 41D

13D 8B, 9B

3B 3D 4B 2B 1A 1B

Page 68

J. AUDIO/COLOR BOARD ASSEMBLY, continued

+1 uf. CERAMIC CAP 25V 1A thru 7A, 9A, 11A, 13A, 1B, 6B, 9B, 11B, 1C, 11C Item Part Number Description

1122-0003-021.C. 74LS04
1222-0001-021.C. 74LS00
1322-0021-021.C. 74LS374
1422-0024-001.C. 4053
1522-0025-001.C. 4175
1622-0056-001.C. 4562
1722-0011-021.C. 741874
1822-0026-001.C. LM324
1922-0054-001.C. 7406
2022-0027-021.C. 74LS86
2122-0028-001.C. 4051
2222-0014-021.C. 74LS139
2322-0057~-001.C. LM377
2422-0029-021.C. 7418148
2522-0030-021.C. 7415151
2622-0031-021.C. 7418174

27 10-1044-1

2810-2204-122pf CERAMIC CAP 16V
2910-1034-1+01 uf CERAMIC CAP 16V
3013-3365-133uf CAP, 25V,

ELECTROLYTIC W/AXIAL LEADS

3113-1075-00100uf CAP ELECTRO-

LYTIC 16V

3213-4755-004.7uf CAP ELECTRO-

LYTIC 16V

3313-1055-001.0uf CAP ELECTRO-

LYTIC 16V

3402-1822-001.8K RES. 1/4W 5%
3502-3322-003.3K RES. 1/4W 5%
3602-1022-001K RES. 1/4W 5%
3702-1062-0010M RES. 1/4W 5%
3802-3012-00300 OHM RES. 1/4W 5%
3902-1042-00100K RES. 1/4W 5%
4002-2232-0022K RES. 1/4W 5%
4102-1052-001M RES. 1/4W 5%
4202-3332-0033K RES. 1/4W 5%
4302-2722-002.7K RES. 1/4W 5%
4402-2732-0027K RES. 1/4W 5%
4502-1322-001.3K RES. 1/4W 5%
4602-6812-00680 OHM RES. 1/4W 5%
4702-3312-00330 OHM RES. 1/4W 5%
4802-1612-00160 OHM RES. 1/4W 5%

Location

5D 6B 1C, 11C, 12C, 13C 2D, 4D 6E, 73, 8E, 9E 5E 10A, 6D 3F, 2 1D 11A, 12A, 4E 7D, 8D, 9D 9A 10E 10B 11B, 12B, 13B 13A

, 13C, 1D 3D, 5D, 7D, 9D, 11D, 13D, 1E, 2E, C7, C9, C10, 3E, 5E, 7E, 9E, C12, 13E, 2F, 4F, 12F, 9E, 2E, 3F c1 C6, C8, C11, C33, IC C13, C15, C17 thru c21

c16

C3, C4, C5

C27, C32, C2

R3, R4, RS R6 R14 R2 R1 R10, R11, R12, R27 R47, 428, R29 R15, R30 R32 R33, R35 R34 R21 R44 R26 R19 R7, R8, R24 R25

Page 69

J. AUDIO/COLOR BOARD ASSEMBLY, continued

Item Part Number

K. 02-8202-00 02-3902-00 07-1032-00 07-1034-00 09-4722-00

29-0002-00 47-0001-00 44-1401-06 44-2401-00 44-2801-00 44-4001-00 44-1601-00 13-4735-00

40-0005-10 37-0009-00

41-0003-00 Description

82 OHM RES. 1/4W 5% 39 OHM RES. 1/4W 5% 10K RES. 1/4W 5% 10K POT 4.7K RES. SIP 3.579545 MHZ CRYSTAL 16 PIN DIP SHUNT 14 PIN DIP SOCKET 24 PIN DIP SOCKET 28 PIN DIP SOCKET 40 PIN DIP SOCKET 16 PIN DIP SOCKET +47 uf CAP ELECTRO- LYTIC 16V 10 PIN MALE CONNECTOR 10 PIN FLAT CABLE ASSEMBLY HEATSINK STAVER V7~-1 E PROM 2716, P2A3A~-1 E PROM 2716, P2A4A-1 E PROM 2716, P2A5A-1 FEMALE 10 PIN PAC 10 PIN

PLANE INTERFACE BOARD 77-0006

Part Number

77-0006- 10-10441-1 22-0001-02 22-0017-02 22-0020-02 23-0045-00 44-1401-00 44-2401-00 Description

PLANE INTERFACE BOARD «UF CAP., 25 VOLT 1.C. 741500 1.C., 74LS166 1.C. 7415245 1.C., 6116 14 PIN SOCKET 24 PIN SOCKET Location

R20 R22, R23 R16, R17, R18, R42, R45 R9, R31, R46 4D

2A 8A, 11E 20, 1A, 1B, 5E 3A, 4A, 5A, 6A, 7A, 2B 3D 3B, 2D, c14 7B, 8B, 9B 4D, 8A, 11E, 6E- 9E, 7D-9D

P21 J2, J3

ONLY W/ 1M277, 3A 4A 5A LM278