Karate Champ Service Bulletin
Karate Champ (US) (Data East USA, 1984) · Service Bulletin · 10 pages · 1 sections · original scan
KARATE CHAMP
SERVICE BULLETIN
We have identified the following technical problems on some of the Karate Champ upright video games manufactured to date. We will point these problems out to you in order of priority and prescribe the necessary modifications needed to fix these problems.
PROBLEM 1 COINAGE PROBLEMS
Symptom:
Symptom: When a coin is inserted into the coin mechanism, the coin meter registers it but instead of a eredit on the screen, the game resets to the attraction mode.
When a coin is inserted a credit is actually shown on the screen but when the player button is pushed to start the game, the screen resets back to the attraction mode instead of starting normal game play.
REFER TO SOLUTIONS, A, B, & C and if problem still persists, perform solution D.
PROBLEM 2 SLOW MOTION VIDEO
Symptom:
Solution: Infrequently you might experience slow motion character movement (1/8 normal speed) on the screen.
IC MODIFICATION
Remove the PCB from the game and determine whether you have the DATA EAST part number DE-0190-0, DE-0190-1, DE-0190-2.
If you have PCB part number DE-0190-0 or DE~0190-1, the following instructions refer to the device at location 11K (74LS74) on the upper PCB.
If you have PCB Part number DE-0190-2,.the following instructions.refer to the device at location 12k (74LS74) on the upper PCB.
- Carefully cut Pin No. 4 at a point very close to the PCB and bend it upward.“ Be Careful not to break the pin off!
- Carefully solder a short jumper from Pin No. 4 to Pin No. 14 of this same device (741874). NOTE: Pin No. 14 is Vee (+5v)
DO_NOT over heat the device. bO NOT use excess solder..
DO NOT allow solder bridging to adjacent pins on the device.
The schematic of the effected circuit is found on sheet 1 of 12 of the NO1-80 PCB in your KARATE CHAMP Player Vs. Player Instruction Manual.
REFER TO DIAGRAM 1
Solution A: ADDITION OF 2 CAPACITORS
For PCB Part Numbers DE-0190-0, DE-0190-1 and DE-~0190-2, perform the following modification on the device at location H8 (74LS04) on the top PCB.
- Carefully solder a 10 MicroFarad (LOMFD), 16 volt tantalum/aluminum capacitor between Pin 3 and Pin 7 of the device (pin 7 is ground). Be careful to observe the polarity of the capacitor! the side marked PLUS (+) must be connected to Pin 3.
- Carefully solder a 10 MicroFarad (1LOMFD}), 16 volt capacitor between Pin 11 and Pin 7 of the device. Be careful to observe the polarity of the capacitor! the end marked PLUS (+) must be connected to Pin ll.
DO_NOT overheat the device. DO NOT apply excess solder, DO NOT allow solder bridging to adjacent pins on the device,
REFER TO DIAGRAM 2
Solution B: COIN DOOR HARNESS MODIFICATION
On the Coin Control Coin Door assembly the following needs to be done on the harness coming out of the coin mechanism. Instead of using Coin 1 socket you want to switch to Coin 2 socket by using either one of the following fixes.
c) Using AWG # 18 (or larger) wire, run a“ ground wire from one of the joystick studs 6n the control panel to the ground stud on the power supply chassis (for Dynamo produced games, run this ground wire to the ground stud at the noise filter which is part of the back door interlock assemble). DATA EAST produced games may already have a ground wire connected to one of the joystick mounting studs. If so, this wire is probably bundied with the other signal wire, and must be clipped out.
REFER TO DIAGRAM 4
1} On the 6 Pin molex connector having male pins. Relocate the wire located in hole 2 to hole 5,
- If you do not have a "Pin Pusher type tool" you may cut the black wire on the - Female Pin Side of the moiex connector, strip the ends of the wire and then tie them up to the wire tocatea an hole 2 of the male pin side of the molex connector.
REFER TO DIAGRAM 3
Solution C: EPROM SPEED VERIFICATION
Examine the proms designated BS 16 through BS 24 on the PC Board. Refer to the attached chart and verify that the speed of the proms desiqnated Bs 16 through BS 24 is 200, 250, or 300 nano-seconds, The manufacturers code will tell you the speed of the proms. 350 ox 450 nano-second proms are slower, and may not work,
If you have 350 or 450 nano-second Eproms, call our toll free number to arrange replace~ ment proms.
You will not be receiving a different program on these Eproms, but rather just faster Eproms. The need for these Eproms should only occur in a very few instances and you should not resort to this unless you have tried all of the above procedures in a step by step fashion.
Solution D: GROUNDING
- Using SWG #18 wire (or larger) jumper from the left coin mechanism to the right coin mechanism,and then to the coin door frame.
- Run a second ground wire from the coin door frame to the ground stud on the power supply chassis. Do not run this ground wire to the logic ground terminal on the power supply.
For games having serial numbers higher than 261000 (produced by Dynamo) run the ground wire from the coin door frame to the ground stud at the noise filter which is part of the back door interlock assembly. You can locate the game serial number and manufacturer by looking at the labels on the back ef the cabinet.
DIAGRAM 1
/ f / /
/F
® fof yp LOCATION fix eo LIK or 12K 2 I {13 74yG74 Za
PINS @isi2es) 0 9 & eget nt
OM TELS 74h BEFORE MODIFICATION
WHEN MODIFIED
PCB
DE~0196-0
LOCATION
8H PINS
PS DIAGRAM 2
13 a
/23¢S5 67 74LS04
COIN SELECTOR
SIDE DIAGRAM 3
MAIN HARNESS
SIDE
EXISTING GROUND WIRE BUNDLED WITH SIGNAL WIRES CLIP THIS WIRE! DIAGRAM 4 GROUNDING
JUMPER LEFT COIN MECH. TO RIGHT COIN MECH. ADD THIS WIRE (use AuwG #18 or i
ROUTE THESE WIRES TO THE RIGHT OF THE COIN DOOR AND AWAY FROM SIGNAL WIRES
TERMINATE THESE WIRES AT THE GROUNDING STUD ON THE POWER SUPPLY CHASSIS FOR DATA EAST PRODUCED GAHES , OR AT THE NOISE FILTER GROUND STUD (DYNAMO GAMES
MANUFACTORE
HITACHI
FUJITSU
OKI
MITSUBISHI
NEC
AMD EPROM
2764-45 2764-35
HN482764 HN482764G HN482764-3 HN482764~-4 HN482764G-4 HN482764G~2
MBM2764-20 MBM2764-25 MBM2764~30
MSM2764AS
MSL2764K
UPD2764D-2 UPD2764D UPD2764D-3 UPD2764D-4
AM2764-20DC AM2764-2DC
AM2764-25DC AM2764DC
AM2764-30DC AM2764-3DC
AM2764-45DC AM2764-4DC SPEED VERIFICATION CHART
450ns MANUFACTURE
HITACHI
MITSUBISHI
INTEL CODE NUMBER
HN4827128G
HN4827128G
HN4827128G
AM27128~-1DC ~2DC AM27128DC AM27128-3DC -4DC ~15DC ~20DC -25DC ~30DC ~45DC
MSL27128K MSL27128K~2 MSL27128K~3
D2764 D27128-4
Karate Champ
© WIRING HARNESS
vo RLWE NiOL ET Hawn Ww ATS RED VIOLET Gar BLUE oe we A
AY P29 x owyr
ORANGE ( Pc-8/82
CN3 CONNECTOR CR7E-44DA-3.96E
O DIP SWITCH SETTINGS
URDNCE RED ~GFNO_ GRR2N Benclu- 1 PLAY Reo YeuoW Q Pery
GREEN RED BLaG REO Reo REO write a uf L down & LP L RIGHT
BLAE yew Yoieon Gee ® O2nNee Brew R ao Doww LEFF leur )
PART INST. SURFACE SOLDERING SURFACE
| Pin Nol | Signal | Pin No | Signal | |
| 1 | 1P RIGHT - DOWN | A | 2P RIGHT - DOWN | |
| 2__|_1P RIGHT - UP | B | 2p RIGHT - UP | ||
| 3 | 1P RIGHT - LEFT | Cc | 2P RIGHT - LEFT | ||
| 4 | 1P RIGHT - RIGHT | D | 2P RIGHT — RIGHT | |
| 5 | 1P LEFT - DOWN | E | 2P LEFT -— DOWN | |
| 6 | 1P LEFT - UP | F | 2P LEFT - UP | |
| 7 | 1P LEFT - LEFT | | 2P LEFT - LEFT | ||
| 8 | 1P LEFT - RIGHT | J | 2P_LEFT - RIGHT | |
| 9 | 1P OPTION 1 | K | 2P OPTION 1 | |
| 10 | 1P OPTION 2 | L | 2P OPTION 2 | |
| 11 | 1P SELECT | M | 2P SELECT | NELLow |
| 12 | COIN 1 | N | COIN 2 | |
| 13 | COIN COUNTER - 1 | P | COIN COUNTER - 2 | |
| 14 | TV. BLUE | R | TV. GREEN | |
| 15 | SYNC. | s | TV. RED |
| 16 ti af
| 17 | SOUND (+) | U | SOUND (-) |
| 18 | +12V | Vv | -5V |
| 19 | +5V | WwW | +5V |
| 20 | +5V | a X | +5V |
| 21 | GND | Y | GND | | |
| 22 | GND | Zz TE exp |
DIP SWITCH
| NO. | SETTING | OPTION |
| OFF | Oo | ON |
1 Type TABLE UP-RIGHT
| OFF | Oo | UN | Music in |
| 2 | NO MUSIC | MUSIC | Attractive Mode |
| 3 | OFF | oO, N | Free Game |
NORMAL FREE GAME
| 4 | oe | o__N | Game Difficulty |
EASY DIFFICULTY
| 5 | OFF | OFF | ON | ON | Game Charge | |
| 6 | OFF | ON | OFF | ON | rere |
p-rig
| me eorn | 1 | 7 | 3 | for Selector-Left | |
| 1 PLAY | 2 | 1 | 1 | ||
| 7 | OFF | OFF | ON | ON | Game Charge |
| 8 | OFF | oN | orr | ON | tapie, up-right | |||
| 1 COIN | 1 | 2 | 3 | for Selector-Right | |
| 1 PLAY | 2 | 1 | f | 1 | a |