Targ Technical Manual V1.1
TARC (Exidy, Inc., 1980) · Manual · 36 pages · 18 sections · original scan
Fovce—-vo— Locso— = i
A
TARG™
Technical Manual 1.1
© 1980 Exidy, Inc. 390 Java Drive, Sunnyvale, California 94086 Telephone: (408) 734-9410 Telex: 357-499
Il.
Ill.
Iv.
vi.
VII.
Figure Figure Figure Figure Figure Figure TABLE OF CONTENTS
TARG Audio Description of Operation .. A. Introduction sssseee . . B. Address Decoding and Input Data Latches C. Clock Divider ..s.eeeeee D. Tone Sequence Generator E. White Noise Generator «++... F. Explosion/Crash Sound Generator .. G. Shot Sound Generator seseeseeeeeeee H. Spectar (Special Target) Sound Generator I. Summing Amplifier and Integrator .. J. Audio Amplifier ....
Logic Description and Operation ssseceseseeeeeeeceeees 5
Audio Adjustments ssscssecceercceecceecessecseceseecee 8B
Power Supply Adjustments ...
«10 +10 ool? ool? ol Mechanical Assemblies ...... A. Control Panel . B. Joystick . C. Monitor .. seeee D. Logic and Audio Boards ..
SchematicS seseesescccsesvsssrscccecesesvsceseseseseeeld
Parts List LIST OF FIGURES
Logic Board Block Diagram . Audio Board Adjustments ...... Power Supply Adjustment ... Control Panel sesseeeeeeeee Four-way Joystick .......ee Logic and Audio Boards .... AURENE
I. TARG Audio Description of Operation
A. Introduction
The TARG audio PCB is comprised of the following functionally distinct sections:
Address Decoding and Input Data Latches Clock divider Tone sequence generator White noise generator Explosion/Crash sound generator Shoot sound generator Special Target (SPECTAR) sound generator Summing Amplifier and Integrator Audio Amplifier
B. Address Decoding and Input Data Latches
A two-to-four line decoder IC at location _l1D detects the combination of the audio board select signal ABSEL and the WRITE signal. The WRITE signal is derived from the CPU read/write signal R/W, logically AND'ed with CPU clock 2 (phase two).
Address line AO (Address Zero) is used to route the incoming data byte from the Logic PCB to one of two 8-bit latches, where data are held until new data are written to the same latch. If AQ is a logical zero at the time of a write to the audio PCB, the latch at location 2C will receive the data byte. If AO is a logical one at this time, the latch at location 2D will receive the data byte instead.
The bits that comprise these data bytes are directly used as enables for the various sound geration circuits.
Cc. Clock Divider The clock divider simply divides the #2 (phase two) clock frequency downward approximately near 706 Khz to approximately 10 Khz. This puts the clock frequency in the proper range to generate the musical tone sequence used for the player (Wummel) image movement.
The clock divider consists of counters 1A and 1B, whose preload combination divides the J2 clock by 71.
Tone Sequence Generator
This generates the musical tone sequence used for the _ player (WUMMEL) image movement. The 10 Khz clock provided by counters 1A and 1B is further divided by counters 3A and 3B to a frequency determined by their preload supplied by PROM 2B.
PROM 2B is programmed to supply the necessary preloads, in sequence by address, to generate a half-cycle of desired tones. The addresses of the PROM are incremented by counter 2A, which counts once each time signal NOTE is set to a high (logical one) state. Setting NOTE high also enables the flip-flop segment 5D which receives the terminal count of the counters (from counter 3B). This terminal count is of short duration, so flip flop 5D simultaneously divides the frequency by two and
creates a 50 % duty cycle (high time = low time) which is
pleasant to the ear. The tone will continue until NOTE is set once again to a low (logical zero) state.
PROM 2B is programmed to supply two different tone sequences. One sequence begins the game and continues until the CPU sets signal UPPER to a high state. This causes the PROM to issue the preloads for the second of the two tone sequences. The second sequence is used when the CPU decides that a sufficient state of tension now exists in the play of the game.
Ee White Noise Generator
This generates the white noise (noise across a wide bandwidth) that is used by the explosion/crash sound generator circuit.
This noise is created by amplifying electron agitation generated in a transistor junction (Q4) which is reverse biased to a degree that causes the junction to “break down".
Transistor Q5 forms a low impedance output source for this noise.
Fe Explosion/Crash Sound Generator
The crash/explosion sound is generated by active-filtering the white noise, and gating it through to the summing amp at the selected time. The trailing edge of the crash/explosion sound is allowed to dissipate slowly (rather than an abrupt halt) due to the discharge of capacitors C35, C36 through resistor R24. The circuit is enabled by signal CRASH, and the trailing edge length of decay can be changed by the use of signal LONG. In this case, however, (TARG), LONG remains in an enabled state throughout the game.
G. Shoot Sound Generator
The SHOOT sound is actually a combination of a triangular wave tone and white noise.
The tone is created by VCO 4B. Its oscillating range is set by pot R10. When signal SHOOT is held low (logic zero state), transistor Ql is turned on, developing a voltage across its emitter resistor R2. This voltage, applied to the control input of amplitude modulator 4A, inhibits the output of amplitude modulator 4A.
When SHOOT is set high, transistor Ql turns off, enabling the Amplitude Modulator output. This also puts a virtual ground on one side of capacitor C29 and results in dragging the control voltage input of VCO 4B low, raising its frequency of oscillation.
The virtual ground at the control voltage input of VCO 4B lasts only as long as it takes C29 to charge up again, so the frequency out of VCO sweeps from high to low.
The tone is given the "hissing" sound by applying a small white noise signal to the base of transistor Ql, which varies the output amplitude.
When SHOOT is again set low, the output amplitude (out of 4A) decreases at a rate determined by the charge rate of capacitor cl4.
H. Spectar (Special Target) Sound Generator
Consists of two halves of a 556 timer IC (5A), both configured in a free-running state.
Signal 5SPEC, when set low, enables both oscillators. The charge/discharge ramp at the THRESHOLD input of the first stage is coupled to the CONTROL VOLTAGE input of the second stage to provide a frequency varying tone out of the second stage. Signal 5WARN, when set high, provides a slowly varying frequency output, and when set low provides a rapidly varying frequency output.
I. Summing Amplifier and Integrator
Two segments of an LM324 operational amplifier are used here. The first is configured as a summing amplifier. It is the common point at which all the various sounds are algebraically added to become one signal which is the composite of all individually developed sounds. Thus this is also the location of the MASTER VOLUME control (R22).
The second LM324 segment is configured as an INTEGRATOR. Its purpose is to eliminate some of the higher frequencies, in order to make a more pleasant sound and also to aid in the prevention of oscillation due to those higher frequencies.
J. Audio Amplifier
The final audio amplifer is a single IC (6A) which is configured as a bridge amplifier. The composite audio signal is applied to the input of one of the two internal segments and the output swings in accordance with the input signal. The feedback on this segment is not only fed back to the inverting input of the same segment, but is also applied to the inverting input of the other segment. This creates a condition wherein one segment swings positive, and the other segment simultaneously swings in a negative direction, creating an output twice the voltage of a single segment.
Il. LOGIC DESCRIPTION AND OPERATION
TARG uses a 6502 MICROPROCESSOR. For more detailed information on this processor, refer to MOSTEK publication #6500-10A, MCS Microcomputer Family Hardware Manual.
The memory in this system is mapped as follows:
0000-00FF Base Page RAM O100-O1FF Stack 0200-03FF Scratch Pad RAM 1800-3FFF Program ROM 4000-43FF Screen RAM 4800-4FFF Character Generator RAM 5000-503F Wummel Image Horizontal Position 5040-507F Wummel Image Vertical Position 5100 On Board Dip Switch (Read) 5100 Wummel Image Rotation Latch 5101 Switch Register 5103 Interrupt Register 5200 Audio Board Register 5201 Audio Board Register FFF7-FFFF Interrupt & Reset vectors
The screen RAM consists of 1K bytes which, when not accessed by the processor, are scanned by main timing to display 1024 squares in a matrix of 32 x 32. The data stored in the screen RAM then selects one of 256 (8-element-wide by 8-line-high) images in the character generator RAM. These 8 x 8 bit blocks fit together to form the playfield imagery. (Alphanumeric characters take one block each to be displayed). The Wummel and its missiles are each positioned by two sets of counters (horizontal and vertical). The actual imagery for these is generated by feeding the outputs of the counters, along with data from a special rotation latch, to the hardware moving object ROM. That ROM then places the correct image in the correct place on the screen. The processor controls this operation by preloading the counters and writing to the rotation latch during vertical retrace.
The processor reads data from the control or option switches by gating the data from the appropriate port onto the bus when the correct address is selected.
The processor controls the operation of the audio board by writing data onto the bus when the address for the audio board bus buffer is selected.
Interrupts can come from three different sources. The first is a synchronous hardware generated interrupt. This occurs regularly at the vertical rate and can be detected by reading the 5L256 bit on the interrupt condition latch. This interrupt is important for providing the processor with a known real time interval used to update the screen, time counters, image velocity rates, etc, The remaining event causing interrupts is the presence of a coin signal on either of the two coin inputs. These are obviously asynchronous and are discernable from each other and from the vertical rate interrupt by testing their respective bits on the interrupt condition latch.
Main address decoding is accomplished by using Al5 through A5 inputs to a PROM. The 5 outputs of the PROM are further decoded into "blocks" in minimum increments of 2K. The signals associated with these blocks are enables for other address decoding circuits that "break up" those blocks. By using lower order address bits, the blocks break into smaller pieces giving peripheral devices a specific, unique address. This is accomplished by loading data from the screen RAM, character generator RAM and moving object ROM into parallel-in/serial-out data at 256 times the horizontal rate. This is the screen element rate. It therefore follows that 256 elements = 1 horizontal line and 256 horizontal lines make a full screen.
ADDRESS
DECODING
WUMMEL /MISSLE IMAGE POSITION COUNTERS
CHARACTER GEN RAM
Figure 1: LOGIC BOARD BLOCK DIAGRAM
TARG™
III. AUDIO ADJUSTMENTS
The following is a diagram of the audio board adjustments.
TARG AUDIO PCB POT CONFIGURATION
(ADJUSTMENTS)
FIRE VOLUME. CRI) (y FIRE CE ty FEEAUENICY VOLUME (R22)
AUDIO To
=, SPECTAR VOLUME ¢ 235) TONE GENERATOR
CRASH EXPLOSION VOL 329
VOLUME (R38) c—"y
Front (component) side
Figure 2. Audio Board Adjustments
IV. POWER SUPPLY ADJUSTMENTS
- Connect a voltmeter to the +5 and ground traces on the logic board.
- Adjust the power supply potentiometer for +5.0 + . voc.
Monitor Isolation Transformer
+12V -12V -5V 5V Power Supply Power Supply
Figure 3. Power Supply Adjustment
ve MECHANICAL ASSEMBLIES
A. Control Panel
To service the Control Panel do the following:
Unplug the power cord.
- Open and remove the back door.
- From inside the cabinet, remove the upper three control panel nuts.
- Open the coin door.
- From the front of the cabinet, swing the control panel out and down; let it rest on the open coin door.
- Check all terminal connections to the pushbuttons and the four-way control.
Figure 4: Control Panel 1 Carriage bolt 4 Control panel 2 Start buttons 5 Four-way joystick 3 Fire button 6 Control harness
B To Service the Four-way Joy Stick
The four-way joy stick is assembled with four long screws and spacers. Four pairs of spring steel cup washers surround the control stick, between the control panel and the top plate (see Figure 4). These cup washers bear against a disk welded to the control stick, and push the stick towards its center (rest) position. Four leaf switches on the bottom plate (activated by the control stick) signal lane changes to the logic board.
Figure 4: Four-way Joy Stick
1 flat head screws 2 control stick 3 upper plate 4 carriage bolt 5 flat washer 6 control panel 7 cup washer 8 spacer, short 9 kep nut 10 lower disk 11 spacer, long 12 switch plate (bottom plate) 13 kep nut 14 leaf switch 15 phillips screw
Do the following to service the Four-way Joy Stick:
- Unplug the power cord.
- Open the control panel by removing 3. black carriage bolts.
- Check the harness connectors to each leaf switch.
- Check the throw of each microswitch; the control stick should activate, but not bottom-out against, each switch.
- If microswitches are broken or switch actuator bent, replace only with Exidy authorized parts. Do not used substitution.
C. To Remove the Monitor do the following:
- Unplug the power cord.
- Open and remove the back door or monitor access panel.
- Unplug the harness connector from the monitor and the Monitor Power Connector.
- Remove the four bolts from the monitor chassis flange mounts.
- Lift the monitor up and slide it out of the cabinet.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Cerin CECODING PROM, 2 esse iS sesaD CLO swe = 8a0rr Pps 2 seat @ Screen FAW (ine, cabo ErePaeC)|
TeaEe ep 1eftsoe)p*\ SRR Pia vomie
ame ye ]*? Lihat scomo
a ~—Bhissrs Tam = 82 RAMs, a a WArRCTER
GENERATOR
ia yoko ourrur
nor useD “TARE Bee Bye 3 [Swen REGISTER
AL prom
seas [x ae stead we
bao es Prom Proce ¢ SIGNAL ‘SeucerioN. wo suunT
USED Foe TARG
DIP SHUNT WOT USED FoR TARE EHARACTER ance STORAGE, Gee Page 3 BP Aievachee RAM sed For Pha gRAM gored chegpoble ig ery
@502 GAMELOGIC ACE
Saal Ge =a WRERIA" GEAPSE HE RTON
Wa aovaos a9vWT Sa I. FEBS 89d 31907 3Wv9 2059 EO a
Cae marr oan oy MYA oo Gane] yy [va pre yA Bie oN
= 2 aL, ¥ aas0 Keabom: ayoabeny> paysunab wyIIOHE ter 750 04 Swvd 95vuaLs 39H youwana9 ysovevi>
Hl 924 31907 BWvO 2059
nes ‘Bwiaoad ssavaay iv
PROGRAM MEMORY
peo 02 19 aoe ry
E 0S co ra
Bae sada
- ne Peary renee WRIA 4
WeLKAnE
PROM _AULRESS
EXIDY INC,
Viz aa TTMIC PCE Pia isore faa
6 OBIECT 1 MOR 2. COUUTERS [moving OBTECT 2 howz. Coueees
& sein mcr s ‘Se al
s [ovine oBseCT 4
VERTICAL COUNTER:
s| i PIPED mene WOWNG oBsEcT 2 VERTICAL COUNTERS|
purg ‘annew rors
sunev ‘Sway (laze mena osrecr” vecoont|
Lwerre_to FOR “TARE”... owns OBJECT 4 = PLAYER IMAGE Comme) mote oszecT 2 = missiLe rT a a aston Sal Som | ee Teac a} EN G302 GAME LOGIC PCE
= =e FISD ak — [Cao TATE REACE OO [movin Gauees FOSiTiOn COUNTERS| 6or8 peach
IMAGE STORAGE’ vives gurrur SiieT REGISTER wang OBTECTS Moura oRseer & moving obmECT 2
ks aed one ino? ver 2 Lavsieel!®
EMORY Device] PERSONALITY SELECTION sseux | 13° rues 3. b ler sit
moving OBTECTS
SHIFT REGIETERS
‘Loab Lore fase usee ru
emevio
[mace sevection Lacie *Caihack Moving O65?) TS0e GIME LOGIC PCB = =e coos] Moving ousetT vidEO GENERATION
cr ve aoa 37 a2°5i504 GND 2089 pesos) a7 PEE
Dav «2 pre en NOIsyaANOD O/¥
Sow, mo2¥I. vera SsRLD
(cren emt Gp ne. i —— [sess BE) vate EE) oeo Gane COLOR DAPTER PCB 77-3373-I
4 T 3 2 T 1
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
sHooT S0OND GeWsRATIOA tiv SPECTAR (SIECAL TARGET) SOUND GENERATION
0 |e eq cat mc334 a 6 aev
cer per 46 + £50 bet 48) ‘5 Low. 33 Ts et les nox 3 h2K (aK a7 cs ster—papt 2 este Lohasr oe a m0 hee Sue She wre nose eh “witeg de 32K oa | en Sle fe, ther ea esz Ssrec_ fo ae cE if |e 0.
SHAOT +5v i- ai veeumer 4k 33K a3 @ 22K sun
lees 7 srccrae Vou:
SwneN Avvo AMP
CRASH GENERATION
tiv Res 12K cay wads4
ores! 4. Jumpers shown indicate cant iguration for LM 79. Amp dip shunt used ty Trange cosPigerstion to UST oo UNIT pin configuration as shown #8 Bypass Cepacitus oleh con dst) 1B EI-CH, Coy 6,629, €24,025, 027,095,093 Rv VowuMme
- 410v Bypass Copacitere(23ph tna lem) sypass Cape a telg, cua : eit-to AA
Schematic ,
17-3371-11 REV B TARG AUbIO PCR | 2 oF 2
24 ver. dame or 35 ver. 2 AMP
REVISIONS
ESORIPTION APPROVED.
Gos i/ :+i2v (Hn)
uT4010. +12 (Lo)
i ' i ] i} '
(on PcB)
NOTES: |. All capacitance values Shun’ tn wicrefirads Gf). TEE) -12v (is) 12 CHi)
60s E UT4010 | } GND
THE HE Poe no PEERS z | _SCHEMATIC
UNIVERSAL POWER SUPPLY
‘OBE WENT NO. DRAWING NO. 7 7-3365-1
‘DO NOT SCALE DRAWING
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
SS@NGNH TENN ICMINGD] 4
SSANQYH NIOD WSMININA,
SaoI2 gue) aIHIoIds 119 TWIP TASeIS OV AvauTOSEY “2 poyrrade arimeogge sper Graunsonaw Zao 08) (runner BH090 as) pope Ems 2 304" fy "Tt sau a2avinsws-now cavinsnt-on
- a in} BOR BO
i ue Drain? an rea] *) ee 0 ine tat jamurvasm - Ree | ew ee
thd
AC Line Cord Harness Assembly
PART # DESCRIPTION
71-2070 AC line cord 60-6020 fuse holder 60-6001 fuse 3AMP slow blo 61-8048 3 pin molex recept 61-8055 individual female pins 88-4002 small tie wrap 61-8051 fast-on push on terminals.8175" 61-8072 TFB butt splice wire list attached
TARG Audio Assembly
48-2321 74118139 48-2314 74L8374 48-2071 74L8112 48-2308 74LS161 48-2210 72748 (TI) 48-2342 LM324 48-2215 NE566 48-2212 NE556 48-2221 MC3340 48-2211 M379 (Dual 6 w audio AMP) 48-2015 7407 48-2302 741804 47-3005 ZN3904 46-3030 IN4454 59-5110 2.2 K resistor 1/4w 5% 59-5100 3.3 K resistor 1l/4w 5% 54-5021 100K potentiometer 54-5019 10K potentiometer
59-5070 22K resistor 1/4 w 5%
59-5125 1K resistor 1/4 w 5% 59-5163 820K resistor 1/4w 5% 59-5025 lmeg ohm resistor l/4w 5%
59-5055 47K resistor l/4w 5% 59-5080 10K resistor 1/4w 5%
59-5140 100 ohm resistor 1/4w 5% 59-5086 6.8K resistor l/4w 5% 59-5069 120K resistor 1/4w 5% 59-5050 68K resistor l/4w 5% 59-5120 1.2K resistor l/4w 5% 59-5095 4.7K resistor 1/4w 5% 59-5045 100K resistor 1/4w 5% 59-5040 150K resistor l/4w 5% REFERENCE LOCATION
PLI Fl Fl Ji Ji
E1-E2 E3
ID 20,2D 3D 1A,2A,1B,3B,3A 6D 5B 4B 5A 4A 6A 4c Ic 3¢ Q1,Q2,Q3,Q4,Q5 CR2,CR3,CR4,CR1 R7 R14 R35 R1,R10,R22,R23, R29,R38 R20,R30,R19, R31,R36,R37 R33,R40,R45,R13 R41 R9-R16,R17,R42, R47, R50 R43 R8,R12,R34,R41, R48 R44 R11 R4,R24, R3 R2,R25,R5, R21,R49,R6 R28,R15 R26
AC Line Cord Harness Assembly, cont,
PART # DESCRIPTION
59-5030 560K resistor 1/4w 5% 59-5065 33K resistor 1/4w 5% 23-4030 «22uf ceramic disk capacitor 23-4035 +luf ceramic disk capacitor
21-4015 6.8uf dipped tantalum capacitor 25v 21-4020 2.2uf dipped tantalum capacitor liv 23-4070 22pf ceramic disk capacitor 23-4060 -O00luf ceramic disk capacitor 23-4050 +O1f ceramic disk capacitor
21-4010 33uf dipped tantalum capacitor 25V 22-4025 «47uf dipped tantalum capacitor 25v 61-8042 10 pin female connector 68-3041 thermalloy 6072 heat sink
74-2506 4-40 x 1/4" machine screw 72-3025 dip package shunt-16 pin amp p-n 435704-8 74-5065 y:32 x 5/8" nylon standoff or 74-5075 6-32 x 1/2" nylon standoff 77-3371 TARG audio [bare] PCB 47-3505 6-32 x V4 machine screw 23-54040 -047uf ceramic disc cap 48-9124-01 6331 PROM [MMI] program #HRA 2B-1
Universal Power Supply PCB REFERENCE LOCATION
R27 R18,R39 641,044 69,C12,C17,031,C32 034,037,042, C43 C14,C021,022,C36 €40, 046,647,050
C48, C49 c45 c11,C13 €1,€2,03,C4,C6,C7, C8,C16,C24,C25,C27 €23,C30,C33,C38, C39
€19,€20,€28,C5,C29
€15,C10,035 32,33 6A for use only with LM379 6A heatsink
6B between logic and audio PCB's
board mounting C76 2B
77-3190 printed circuit board 20-4000 4000 uf 50v axial lead capacitor 21-4010 33uf 35v dip tantalum capacitor 21-4015 6.8uf 35v dip tantalum capacitor 46-3016 60SI diode 47-3004 MDA 970-1 bridge rectifier 47-3041 2N3055 transistor 47-3011 2N6246 transistor 48-2337 7905T negative 5v LM320T-5 regulator 48-2217 7912T negative 12v LM320T-12 regulator 48-2338 7812T positive 12v LM340T-12 regulator 68-3041 thermalloy 6072 heat sink
Universal Power Supply PCB, cont.
PART #
68-2038 61-8010 74-2514 74-5216 74-5191 DESCRIPTION REFERENCE LOCATION
thermalloy 6015 heat sink 12 pin male molex 4-40 x 3/8 phillips pan head machine screw #4 flat metal washer #4-40 kep nut
Monitor Isolation Transformer Assembly
FR 63-4029
61-8058 61-8054 61-8057 61-8055 isolation transformer midwest 773P7 molex connector 03-09-2032 AC input P22 male molex pins 02-09-2118 P22 molex connector 03-09-1023 AC to monitor J23 female molex pins 02-09-1118 323
6502 Game Logic PCB Assembly
48-2000 48-2005 48-2010 48-2015 48-2020 48-2332 48-2035 48-2316 48-2045 48-2055 48-2067 48-2071 48-2307 48-2321 48-2090 48-2095 48-2100
48-2115
48-2328
48-2350 48-2314 48-6502 48-2334
48-9125-01
48-9099-01 Ic 7400 3D 15H Ic 7402 1H 6H 8F Ic 7404 ID 3F 4D 10F LIF Ic 7407 2c IC 7408 SE IC 74LS11 3H Ic 7420 2F IC 74L821 12F 15E IC 7427 7F 2H IC 7432 6F Ic 7474 IC 5H IC 74L8112 2E 6E IC 74L8138 5B 5D IC 74L8139 73 16H TC 74157 14A 14E IC 74161 1E 2D 4F SF IC 74166 12B 12D 13D 14D 15D IC 74193 10E 12E 13F 15F 14F 16F 11E 13E IC 74L8241 8C 1A 3A 3B 4H 6B 7D 9B 9E 15A IC 74LS 245 3C 4C 6C 15B 13B IC 74L8 374 1F 14B 7C 8E 6502 microprocessor 2A 2114 [1Kx4] RAM 44 5A 7B 8B 11C 12¢ 13¢ 14c 2708 EPROM [1Kx8] HRL 110-1 11D [use w/ hdwe moving objects] 6331 PROM [32x8] 6D
6502 Game Logic PCB Assembly, cont.
PART #
48-9099-02
48-9099-04 46-3025 59-5135 59-5120 59-5115 59-5110 59-5105 59-5095 59-5080 51-0003
51-0002 51-0001 51-0004 23-4033 23-4035 20-4011
20-4014
20-4005 F2-Fa25 72-3042 45-3036 61-8041 61-8062 77-3361-14 61-8045
61-8035 61-3060 48-9126-04 48-9126-03 48-9126-02 48-9126-01 48-9126-05 DESCRIPTION
6331 PROM [32x8]
6301 PROM [256x4] IN4002 diodes 470 ohm resistor v4w 5% 1.2K 1.8K 2.2K 2.7K ohm 4.7K ohm 10K 1/4W 2200hm 1/4 w 5% 8 sip 2.2K 1/4w 5% 8 pin 4.7K 1/4w 5% 8 pin 6.8K l/4w 5% 8 pin +Olmf ceramic disc resistor resistor resistor resistor resistor ohm ohm ohm l/4w 5% l/4w 5% l/4w 5% l/4w 5% l/4w 5% 5% resistor pin resistor
resistor sip resistor sip resistor sip capacitor slmf ceramic disc capacitor 6.8uf dipped tanta 25v lum capacitor
33uf dipped tantalum capacitor 25V 470uf 10v electrolytic capacitor dip shunt jumper paks 16 pin 8pos dip switch 11.289 mhz crystal 10 pin male molex connector 16 pin low profile dip sockets printed circuit board 24 pin low profile
profile profile 40 pin low 14 pin low 2716 EPROM 2716 EPROM 2716 EPROM 2716 EPROM 2716 EPROM programmed programmed programmed programmed programmed dip
dip socket dip socket HRL 6A-1 HRL 7A-1 HRL 8A-1 HRL 9A-1 HRL 10A-1 sockets REFERENCE LOCATION
14H use w/ moving objects 5c 8F 1D 2C 7H 1c 2c 2A 1c SH 7H 9E hdwe
9E
2C SH
16A 15A 14A 1D air (per Assy dwg) 1C 6E 15D 6H
1c 2¢
10H 4B 10B 10D 11B 16A 1D 16C 16E 3E 4E 5C 6C 14H
9A 10A 11D 6A 7A 8A 2A 16B 6A TA 8A 9A 10A
6502 Color Adapter PCB Assembly
PART #
48-2080 48-2305 48-2321 48-2079 48-2341 48-2333 20-4011 59-5136 59-3103 23-4033 61-8203
61-8127
77-3373 DESCRIPTION
Ic Ic Ic Ic Ic Ic 74151 74LS74 74L8139 74148 74LS86 74L8174 6.8uf dipped tantalum capacitor resistor 330 ohm l/4w 5% 9 pin sip resistor pak 1Kohm -Oluf ceramic disc capacitor pin male molex connector +156 center pin socket stan-profile w/lock printed circuit board REFERENCE LOCATION
5A 5B 5C 1A 2A 2B 1C 6A 6B cl RITHRU R10 3A 3B 3C C2 C4 C5 C6 P2
Jl