Rampart TM-359 1st Printing Universal Kit
Rampart (Trackball) (Atari Games, 1990) · Kit Manual · 48 pages · 62 sections · original scan
TM-359 1st printing
ea ST pss
Universal Kit
Installation Instructions
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Conversion kit for upright games
Copyright © 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If A‘ 7 ee wn catsingers NWA are convicted, courts can order destruction of the infringing articles. iPad
In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases, Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Coxporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed inthe U.S.A. 4/91 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner Rampart Universal Kit
NOTICE RE.
NoON-ATARI
PARTS
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
- All ground wires in the game are properly cennected as shown in the game wiring diagram.
- The power cord is properly plugged into a grounded three-wire outlet.
- The game printed-circuit boards (PCBs) are properly installed with alll screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Rampatt Universal Kit
SAFETY SUMMARY
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
iii
CONTENTS
1 Set-Up How to Use This Manual... Cabinet Equipment Requirements Tools Required. Inspecting the Kit Preparing the Cabinet for the Kit Installation . Assembling the Control Panel... Connecting the JAMMA Harness Installing the Rampart Game PCB Installing the Bezel, Decals, Labels, and Attraction Assembly Setting the Coin and Game Options. Maximizing Earnings Game Play... Hole-Cutting Template. 2 Self-Test Introductior Entering anc Select Test Men Statistics ...... Game Options. Coin Options. Sound Test. Rampart Universal Kit
Controls Test....... - Complete RAM Test. Complete ROM Test. Playfield Test... Motion Object Test Color Test...... Color Purity Test Convergence Test 3 Maintenance and Troubleshooting Introduction Video Display Sync Problems Troubleshooting Joystick Control: ROMs and RAMs.. 4 Parts Illustrations See the List of Illustrations that follows.
5 Schematic Diagrams See the List of Illustrations that follows. ” Statistics Sheet
Rampart Universal Kit
ILLUSTRATIONS
Figure 1-1 Figure 1-2
Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Installed Kit Parts 0 Locations of Control Panel Holes to be Drilled
Self-Test Menu Screen Statistics Screen... Game Options Screen Coin Options Screen Sound Test Screen .. Controls Test Screen RAM Test Menu... Complete ROM Test Screen . Playfield Test Screen .. Motion Object Test Screen Color Test Screen..... Convergence Test Scree1 Figure 4-1 Figure 4-2
Figure 4-3
Figure 5-1 Parts for Rampart Universal Kit........... 8-Position Microswitch Joystick Assembly .. Rampart Game PCB Assembly
Rampart Game PCB Assembly Schematic Diagram
Table 1-1 Table 1-2 Table 1-3
Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5 Table 2-6
Table 3-1 Table 3-2 able 3-3 Table 3-4 Equipment Requirements Contents of Rampart Kit JAMMA Pin and Wire Connections.
Summary of All Self-Test Screens Game Option Settings . Coin Option Settings When to Run the RAM Tests . Bad RAM Locations by Error Address Bad ROM Locations by Error Address ’ Troubleshooting Table. Voltage Inputs and Test Points on “the PCB “= What-ROM Problems Look Like. Atari Games Video Connector Pin _Assignments
Rampart Universal Kit
vi
CHAPTER Installation
This manual provides information for installing, testing, and troubleshooting the Rampart™ conversion kit. & Chapter 1 describes how to instali the Rampart kit in your cabinet. This chapter also describes game play. * Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Rampart game. You can troubleshoot the PC boards, main circuits, and controls using the screens in the self-test. You should regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. * Chapter 3 contains contains troubleshooting and maintenance procedures for the joystick control. Chapter 4 contains the kit parts list and parts illustrations. * Chapter 5 contains the schematics for the Rampart game PCB.
Installation
Cabinet Equipment Requirements
Table 1-1 lists the equipment required in the cabinet into which you are installing the Rampart kit.
Table 1-1 Equipment Requirements Equipment Specification Video Display Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to-peak.» | positive polarity ©: Control Panel Metal only Speaker 8Q, 10W Coin Counter +5 VDC or +12 VDC re Three-conductor with ground +5 VDC + 0.25V @ 3.0 amps +12 VDC @ 1.0 amp -5 VDC @ 1.0 amp (optional) Power Cord Power Supply
Tools Required
- Drill with a 1/2-inch and 5/16-inch drill bits ° Phi ips screwdriver
¢ Flat-blade screwdriver
- Socket wrench set and ratchet
© 1/4-20 hex wrench
¢ Wire cutters and strippers © Straight edge *° Squeegee ° X-ACTO™ knife
- Insulated wire connectors (if you are installing a new JAMMA harness)
- Carbon paper
- Saber saw
- File
- Bandsaw
- Tape or glue
Table 1-2 Contents of Rampart Kit
| Part No. | Description | “Part No. | Description |
| 72-6608S | #6 x 1/2"-Long, Type AB, Pan-Head, | 160044-001 | Snap-Action Switches (8) |
| Cross-Recessed Screws (4) | 175014-1040 | #10 Flat Washers (8) | |
| 7551123 | #10-24 x 3/4"-Long Black Carriage Bolts (12) | 178032-002 | #10 Wire & Cable Tie |
| 177026-0040 | #10-24 Nut/Washer Assemblies (12) | 178237-001 | Red Button Assemblies (4). |
038158-01 Product LD. Label i ass See y 178237-005 Blue Button Assemblies (4) :
| 039450-01 | FCC Compliance Label | 178265-001 | L-Style Nylon Standoffs (4) |
| 047205-01 | Shield, Attraction | 048437-01 | Set of Eight Labels for Buttons |
| 047209-01 | Control Panel Cover | (lace Piece/Fire/Start and Rotate 0° | |
| 048451-01 | Control Panel Decal | Piece/Speed-up in ‘both blue and red). |
A040933-03 8-Position Microswitch Joystick Assy. (2) 04845201 Side Panel Decals (2) re aa
| 048453-01 | Attraction Panel Film | A046501-01 | JAMMA Harness Assy.” | ie |
| 048455-01 | Monitor Bezel with Graphics | . | 8 048869-13 | Rampart Kit PCB Assy. |
| 048879-01 | Instructions Label for Monitor Bezel | “ | TM-359 | Rampart Universal Kit‘Installation |
| 141026-001 | -50"-Inside Diameter Ferrite Split Beads (2) | Tnstruciioils Gwith control panel template) |
5 eS Packaging materials are'nol listed. All ‘parts are a sean) sa of 1, except as. noted in parentheses.
1-2
Rampart Universal Kit Installation
4720501 049453-01, Atraction Shield 1 traction Film items Not Shown: ‘AD46S0T-01 JAMMA Harness Assy. TM.359 Rampart Universal Kit Installation Instructions 049455.01 Borel With Graphics
048452-01 048879-01 | Side Panel Decal Instructions Label (2 places)
7551128 | #024 x 314" Cariage Bolt| ‘A048869-13 srigea0% Rampart PCB Assy. #10-24 Nt Woaher Assy. Cae men erancti r7sote0%0 ‘efecoos HOPI Wate ¥6x 112 Pant, y Gross-Rec, Type-AB Screw (4 places)
178237-005 Blue Button Assy. c, (4 places) +160084-001 3 Snap-Action Switch “@ (4 places) 0040933-03, Position Microswitch Assy. 176237-001 (2 places) Red Bution Assy. (4 places) 04045401 160084-001 ‘Control Panel Decal Ging acuen Such (047208-01|
- (places) 7551128 Cont Pane Cove Hoaer st Carage eos vourcont OTE 5 14 places) our game cabinet may n Control Pane! instructions Label tate lan separ auseny as shown 410 Flat Washer this ilustraion. The picture (places) shows the conirol panel and 17026-0040 electronic pars installed in a 10-24 Nut-Washer Assy. 'ypical game cabinet. (4 places)
Figure 1-1 Installed Kit Parts
Inspecting the Kit
Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Rampart kit serial number, part number, and description of the missing or damaged parts, and date received. Preparing the Cabinet for the Kit Installation
Installation Rampart Universal Kit
Table 1-3 JAMMA Pin and Wire Connections
Component Side ae 1 “BN GND”
“Connect to the +5V terminal on the ‘power supply. However, i ‘+SENSE | terminal; connect are eof th wires at pin 3, 4, or Cito terminal of the power supply. 12V RTN or the 5V-RTN (GND) or leave it unconnecte:
6 Yen ee HV Connect to the +12V terminal of the power supply. : # Ses og “If your coin n counters) require 12V, also connect to the +,
Not used _ r SPKR + W ©. Not used 3 ES = 12, OR “RED ‘Attach to the video display.
- BU BLUE Attach to the video. display. 14 BK VIDEO GND » Attach to the video display... : 15... W SELF-TEST. Use this wire if you want an external self test switch, However, the kit : = test switch on the PCB. Ufyou connect an external self-test switch, switch off tb switch 01 “the PCB. Connect the wire to the N.O. terininal on the external se common terminal ie the switch loa BRC dire [GND], LT COIN" a - 7 W/BK. PLYR 1 i ROTATE common terminal of the switch to-one of the BK/W wires. 18 ©. W/BN” PLYR1 ‘Connect to the N.O; terminal of the switch. Conne ae JOYST UP to.one of the BK/W wires. PLYR 1 same as pin 18. oe © JOYST DN 20 PLYR1 "Same as pin 18... “@ JOYST LT © Bee 21° W/Y PLYR1° Same as pin 18. JOYST RT 22 W/GN | PLYR 1 PLACE
- W/BU.. Not used
- WIN Not used 25 W/GY*. Not used 26 NV Not used i 7 : 27... BK/W “GND “Connect one of the BK/W wires at pin 27, 28, €, and the power supply (if it exists) and‘one to the commor Connect two of these wires to ‘the common terminals oft
1-4
Rampart Universal Kit Installation
Table 1-3 JAMMA Wire Connections, Continued.
: Wire
| Pin | Color | Signal |
Solder Side aa E ‘ee
| A | BN | GND | Connect to the 5V RIN (GND) términal on the Bote supp | However ify | have 12V |
RTN, connect one of the BN wires at pin 1,2, A, orB io the 12V RIN | termin :
| B | BN | GND | Same as pin A. |
| c | R | *5V | Connect to the +5V terminal on the power supply. However, if your power supply has a : |
+SENSE terminal, connect one of the R wires at pin 3, 4s orc to +SENSE instead of +5V.
| D | R | +5V | Same as pin C. | : | a |
| E | OR | sv | Connect to the -5V terminal of the power supply. If -SV is not availa le, ce |
12V RTN or the 5V RTN (GND) or leave it unconnected: :
NOTE: If you do not have (or 10) —SV, the maximum m power tou
by half.
F Y +12V Connect to the'+12V terminal of ihe power wp
H Key :
| J | V/V | COINCTR2 | Connect this wire to one side of the right Lv coin counter. Clip R28 on the game PCB if |
you use a second coin counter. Note: Do not use 24V counters. ect thé + side to +5V_ or +12V on the power supply, as appropriate, K Not used
| L | w | SPKR- |
M Not used
| N | GN | Attach to the video display. |
| P | BN | Attach to the video display. |
| R | GY | Service |
s Not used
| T | OR | RT COIN | Connect to the N.O. terminal of the right coin swith, Connect the common termi 2 |
the switch to a BK/W wire.
| U | Y/BK — PLYR2 | Connect this wire to the N.O. terminal of the PLYR | ROTATE switch. Connect the |
ROTATE common terminal of the switch to'one of the BK/W wires.
| v | Y/BN | PLYR2 | Connect to the N.O. terminal of the: ‘ovite |
JOYST UP to one of the BK/W wires. * “
| Ww | Y/R | PLYR 2 | Same as pin V. |
JOYST DN
| x | Y/OR | PLYR 2 | Same as pin V. |
JOYST LT
| Y | Y/w | PLYR 2 | Same as pin V. |
JOYST RT
| zZ | Y/GN | PLYR 2 PLACE Connect this wire to the N.O. terminal of the PLYR 2 PLACE s' |
common terminal of the switch to one of the BK/W wires:
| a | Y/BU | Not used | - | yes |
| b | Y/V | Not used | ||
| c | Y/GY | Not used | ||
| d | GY/W | Not used | ||
| e | BK/W | GND | Connect one of the BK/W wires at pin 27, 28, e, 01 |
power supply (if it exists) and one to the common terminals of the coi nect two of these wires to the:common terminals - the‘control switches on the panel. 2 i
| f | BK/W | GND | Same as pin e. |
1-5
Installation
Figure 1-1 shows almost all kit parts installed in a typical cabinet. Use this illustration as a guide while you instal] the parts.
- Turn off power to the game, and unplug the power cord.
n . Remove the following from the cabinet: ° Existing PCBs « Game harness, if it is not Japan Amusement Machinery Manufacturers Association (AMMA)— compatible
- Control panel decals, labels, and controls
- Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals.
- Video display (monitor) shield, display bezel, attraction shield, and marquee.
- Wipe down and vacuum the cabinet. Paint the cabinet, if required.
Assembling the Control Panel
Parts Needed
To assemble the control panel, you need the control panel hole-cutting template, which is printed on page 1-11. Cut out the template sheet from the manual. You will also need the following parts from the kit:
- Clear cover for the control panel Rampart Universal Kit
- Control panel decal
- Four red and four blue button assemblies ¢ Eight snap-action switches
- Eight control-panel button labels (on a sheet) © Two joystick controls
- Eight #10-24 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the joysticks
¢ Four #10 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the corners of the control panel cover
Installing the Parts
- Using carbon paper, transfer the joystick mounting pattern from the template to the contro! panel. Save the template. Also refer to Figure 1-2 for the exact locations of all holes.
- Drill four %" holes in the metal control panel for each joystick’s mounting bolts.
- Using a saber saw, carefully cut out the large holes for the joysticks. Deburr the sharp edges with a file.
- Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the eight button holes as close as possible to the locations shown on the template.
1.187" Dia. & & B+ &-+ (6 places) fe 275" 275—t = |
i OF Set €+) ‘ a 8] 58 , TOS 1 | 4 | 1-904 ' NOTE 1450" er { 11] | The four holes in Fy 1.187" Dia. ''] | the corners are | (places) || | not shown in this ' illustration. Dritl these holes wher- Suggested distance from *1.50"| 4.75" Dia. [150° ever space perfront of control panel. Check 3.00" (places) * 800. mits. that the joystick controls “ | have sufficient clearance before cutting holes. CL
Figure 1-2 Locations of Control Panel Holes to be Drilled
Rampart Universal Kit
Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners—wherever space permits.
- Using a bandsaw, cut the control panel cover to its correct outside shape.
- Tape or glue the temiplate to the plexiglass cover. To start the saber saw cut, drill a 1/2" hole inside the joystick holes and the button holes.
- Saw out the two large joystick holes and the eight button holes.
- Drill the four 5/16" holes that will be used to mount the cover to the control panel and the eight 5/16" holes to mount the joysticks. 9, To prevent injury, carefully deburr all the edges of the plexiglas cover.
- Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.
i . Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts. me =)
- Install the joysticks using the eight 3/4"-long carriage bolts. Install the eight button assemblies and the eight labels. For maintenance and servicing information on the joystick controls, refer to Chapter 3 of this manual. Installation
Connecting the JAMMA
Harness
- If your game cabinet does not already have a JAM- MA harness, install the JAMMA harness in the cabinet.
- Install the split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit.
- Using Table 1-2 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
Connecting Power Wires
- Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Rampart kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, -SV, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.
Connecting Video Display Wires
Installation
Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.
Connecting Coin Door Wires
- Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
- Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.
Connecting the Control Wires Connect the joystick harness and the button harnesses to the JAMMA harness using crimp splices or butt soldering, according to the information in Table 1-3.
Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.
Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.
1-8 Rampart Universal Kit
Installing the Rampart
Game PCB
1, After you have checked the power on the JAMMA connector (above), install the Rampart game board set in the cabinet. Use the nylon standoffs and four #6-32 screws in the kit.
- Connect the JAMMA connector to the PCB.
- Secure the JAMMA harness away from the PCB with cable ties.
- Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.
Installing the Bezel, Decals, Labels, and Attraction Assembly
The kit parts are shown assembled in a cabinet in Figure 1-1,
Installing the Display Bezel Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required.
Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC compliance label (part no. 039450-01) on the back of the cabinet.
Installing the Side Panel Decals Find the side panel decals in the kit. Wet the left and tight side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.
Installing the Attraction Assembly Find the Rampart attraction shield and the attraction film in the kit. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.
Rampart Universal Kit
Setting the Coin and Game Options
Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.
Maximizing Earnings
For maximum earnings, regularly maintain your Rampart game following the instructions in Table 3-1, in Chapter 3. When you set up the game and when you collect money, perform the automated selftest and check the controls with the Controls Test in the self-test.
Game Play
This section describes the theme of the Rampart game and the game play features.
Introduction
Rampart combines the best of strategy puzzle games with dynamite action and the excitement of head-tohead competition. Two players can play at once to see who becomes the medieval overlord. Installation
Play Mode In the first phase of game play, players select a site for their home castle and position their cannons. Then, it’s on with the battle, as each side hurls projectiles to destroy enemy walls. Once the onslaught ends, the players must quickly rebuild and extend their walls before the next battle. The players must completely surround at least one castle in order to continue play. In a two-player game, the contest is head-to-head for an operator-selectable maximum number of battles (the factory setting is for seven battles per game). As long as a player can place pieces to surround at least one castle, he continues. If a player is eliminated, he may deposit another coin to continue. In a one-player game, the computer directs an invading armada against the player’s castles. The objective is to establish a fort and expand your realm to the entire island. You must destroy the computer's fleet before they reach shore and move their cannons onto the land. In higher levels of game play, the computer cannon fire will leave behind burning rubble, preventing the player from repairing and extending his walls. Rampart’s action is lightning fast. The strategy is exhilarating. The thrill of head-to-head competition is intense.
Installation Rampart Universal Kit
1-10
1-11 Rotate/Speed-up
ATARI
GAMES
Place/Fire
Hole-Cutting Template for
Rampart” Kit Control Panel
Rotate/Speed-up Place/Fire
NOTE
To accommodate different playing styles, it
portant to install all eight button assemblies on the contro! panel. Trak-ball players are used to buttons on the left side of their controls, and joystick players are used to buttons on the right. With buttons installed on both sides of the joysticks, you reduce the potential for
player frustration.
Installation Rampart Universal Kit
CHAPTER 2 ~6hSelf-Test
INTRO! TION
Use the Rampart self-test to check the condition of the game circuitry and controls. You will see the self-test information on the video display and hear the sound test information through the speakers. You do not need any additional equipment to perform the self-test. ¢ You should perform the self-test when you first set up the game, each time
you collect the money, or when you suspect game failure. This chapter shows the screens in the self-test and explains each of the tests. The screens and explanations are arranged in the order they appear in the selftest. Table 2-1 lists all of the self-test screens
and their purposes.
Self-Test Rampart Universal Kit
Entering and Exiting
the Self-Test
To enter the self-test, turn on the self-test switch on AHS
| the game PCB. Exit the self-test by switching off the | AME | OPTIO |
| self-test switch. | OIN | OPTIONS |
Select Test Menu “ConTROLS TES
| Choose which test or screen you want to see from this | COMP | HOM |
menu, shown in Figure 2-1. Move up and down the PLAYFIELD TES
| list by moving the joystick; the corresponding test is | MOTION | OBJECT | TE: |
highlighted in white. Choose the screen by pressing COEOH the red PLACE button. gy :
Statistics
Use the information shown on the statistics screen, in Figure 2-1 Self-Test Menu Screen Figure 2-2, and on the histogram screens to keep track of your game use and maximize your profits. Record Press the red PLACE button to leave this screen and go the information on the Rampart statistics page in the to the histograms. back of this manual. The statistics are collected from * Left Coins show the number of coins counted in the last time the statistics were cleared. You can clear the left coin mechanism. the statistics by holding down the red ROTATE button and pressing the red PLACE button at the same time. Right Coins show the number of coins counted in the right coin mechanism.
Table 2-1 Summary of All Self-Test Screens
Screen 6 a Use or Purpose
| Statistics Screen | «© | << Displays the game statistics. | ° |
Game Options Screen Use to set and check the game options settings.
| Coin Options Screen | Use to set and check the coin options settings. | . | : | sabe | |
| Sound Test Screen | . | Use to check the audio circuits. | i | ‘ | ie: |
| Controls Test Screen | Use to test the player controls.) | 0 | : |
RAM Test Screen ; at S sis Srey Video RAM (looping) Use to check the video RAM. Color RAM Cooping) Use to check thé color RAM. All RAM (ooping) Use to check all RAM
| ROM Test Screen | : | Use to check the program ROMs. |
| Playfield Test Screen. | . | _ Use to check the alphanumeric displays. |
Motion Object Screen Use to test the movement and color of game objects.
| Color Test Screen | ° | Use to check a video display color circuits. | 4 |
Purity Test Screen " vot Red Color Purity Screen Use to check the red color purity in the video display. ‘Green Color Purity Screen? * Use to check the ‘green color purity in the video ‘display. Blue Color Purity Screen ©, “‘Use to check the’ blue color purity in the video display. White Color Purity Screen Use to check the white color in the video display... Grey Color Purity Screen Use to check the grey color in the video display. White Convergence Screen Use to check and adjust video display convergence of red, blue, and green. Violet Convergence Screen Use to check and adjust video display convergence of red to blue: Green Convergence Screen Use to check and adjust video display convergence of red and blue to green.:
e b
Rampart Universal Kit Self-Test
- Avg Time/Coin is the average number of seconds played per coin. ¢ Percentage Play is the amount of time, as a percentage, that the game is played while it is powered on.
Game Options
Check and select the coin options on this screen, shown in Figure 2-3. To move through the options, move the joystick up or down. Change the option in yellow type. The factory default settings are shown in green. To change a set- 6 ting, move the joystick right or left. To save the new settings, press the red PLACE button. This returns you
| 6 | Oi | 3 | ||
| AVG TIMECOIN | 6 SECS | aay | ||
| i | pe | : | RESTORE | FACTORY OPTIONS |
OLD RED ROTATE AND PRESS RED BLAG o.
| OCLEAR | CLEAR | SCOR |
PRESS BED PLACE BUTTO OR SCRE
| Figure 2-2 Statistics Screen. | A | DS | R ADD-A-CO |
| * Aux Coins shows the number of coins counted on | ss | a | chy |
the auxiliary coin input.
| * Idle Mins shows the number of minutes the game | 5 hen | aes reste |
was not being played. pH RED PLACE BUTTO
| * | 1 Player/2 Player Mins are the number of minutes | ae | Se | gue |
the game was played by one or two piayers.
- New Game Mins is the amount of time the game is played before continuation. ° Cont Game Mins is the amount of time the game is played during “add-a-coin” (continuation).
- Left/Right Pir Mins are the number of minutes the game was played at the left and right player stations. « Active Minsis the number of minutes the game was being played in any mode.
- Total Games is the number of games played (one game per player).
- Total Sessions is the number of sessions piayed. For example, one 2-player game counts as one session. + 1-PI Beginners is the number of 1-player beginner games played. ¢ 1-P! Advanced is the number of 1-player “veteran” games played. ° Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 38F. Figure 2-3 Game Options Screen
to the select test screen. If you want to keep the original setting, although you have changed it, press the red ROTATE button. This brings back the original setting. Use the red PLACE button to exit. The game option settings with factory defaults are shown in Table 2-2.
Coin Options
Check and select the coin options on this screen, shown in Figure 2-4.
2-3
Self-Test Rampart Universal Kit
Table 2-2 Game Option Settings
Explanation. Option e026 Settings Restore Factory Options * Yes Nov.
Clear High Scores Off Onv Game Difficulty Easy Medium 7
Hard Very Hard
Length of 2-Player Game 5, 7¥, 10, 15 battles
Additional Rounds After 2, 4a, 6,8 Add-a-coin ee
Auto-Reset High Scores off Ondo
© Pres programmed obstacles and more enemy Cantons:
V Manufacturer's recommended settings. These settings are shown in green on the screen: “Lets you adjust the additional
“within the previotis 200 games », Lets you clear the high score table.
being fired contribute to increased difficulty.
Lets you adjust the maximum number of rounds (battle
aliowed for two-player games.
after an adds l-a-coin: in ‘ulti Neves games.
To move through the options, move the joystick up or down. Change the option in yellow type. The factory default settings are shown in green. To change a setting, move the joystick right or left. To save the new settings, press the red PLACE button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the red ROTATE button. This brings back the original setting. Use the red PLACE button to exit. The coin option settings and factory defaults are explained in Table 2-3.
Sound Test
The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-5.
GIN OPTIO
FREE PLA , AME COS G RED
| BONUS | FOR QUA | B |
ON
| A | ECH | VA |
| 2) | OUNT | SIN |
| GIN | COUNTS | AS7t CO |
PRESSING RED ROTA RESTORES ORIGINA G PRESS RED PLACE BUTTO OSA SETTING AND
Figure 2-4 Coin Options Screen Shoes
BER OF SOUND 0
OUND
Pp RED ROTATE 8 O HEAR SOUN MOVE JO S) OUND PRESS RED PLACE BUTTO O RETURN TO
Figure 2-5 Sound Test Screen
Use the joystick to select the sound and press the red ROTATE button to listen to it. Pressing the red PLACE button returns you to the select test menu.
Controls Test
The controls test screen is shown in Figure 2-6. Test the coin mechanism switches, control panel buttons, and joysticks. As you use the control, the red control name changes to yellow on the screen. If the name does not change to yellow, check the connections, switches, and mechanism. Simultaneously press the red ROTATE and red PLACE buttons to return to the test select screen. Moving each joystick causes the yellow hexadecimal numbers to change when you move it up and down (UP/DN) or left and right (LT/RT). Use these numbers to help correctly orient the joystick, if you are installing a new one. If the numbers on the screen do not
Rampart Universal Kit Self-Test
Table 2-3 Coin Option Settings
Option Settings “, Explanation . es Free Play Discount to Continue
Game Cost
Bonus for Quantity Buy-in
Right Mech Value
Left Mech Value Nov Yes Nov Yes
1 coin 1 credit¥ 2 coins 1 credit
8 coins 1 credit None W 2 coins give 1 (extra coin) 3 coins give 1 (extra coin) 3 coins give 2 (extra coins) 4 coins give 1 (extra coin) 4 coins give 2 (extra coins) 4 coins give 3 (extra coins) 5 coins give 1 (extra coin) 5 coins give 2 (extra coins) 5 coins give 3 (extra coins) 6 coins give 1 (extra coin) 6 coins give 2 (extra coins) 6 coins give 3 (extra coins) 7 coins give 1 (extra coin) 7 coins give 2 (extra coins) 7 coins give 3 (extra coins) 8 coins give 1 (extra coin) 8 coins give 2 (extra coins) 8 coins give 3 (extra coins) 9 coins give i (extra coin) 9 coins give 2 (extra coins) 9 coins give 3 (extra coins) 1 coin counts as 1 coin YW
8 coins count as 1 coin 1 coin counts as 1 coin”
8 coins count as 1 coin
V Manujacturer’s recommended settings. These settings are shown in green on the screen. en Set this to “Yes” for demonstrating the game. ’, ie Léts you offer a reduced price per credit when players want to continue a game. ae Sets the number of coins required for one credit. ag
Lets you choose various levels of bonus coi ‘Or no bonus.
Is the number of coins each coin counts as the right coin mechanism. :
Is the number of coins each coin counts as in the “) left coin mechanism,
PR BUTTONS AND MO OG Ci PLACES RIGHT PLA RO R HOTA
R if
DO pow
AND BED PLACE BUETO 83 NU
Figure 2-6 Controls Test Screen change, check the connectors and harnesses for that direction of movement.
Complete RAM Test
Use this selection screen, shown in Figure 2-7, to choose which RAM test you want to perform. Use the different tests according to Table 2-4. If you get an error in any of the RAM tests, see Table 2-5 for more information, If you have serious RAM problems, you may see only a colored screen. Press the red PLACE button to leave the individual RAM test and return to the RAM test menu screen. Press the red PLACE button once more to return to the test select screen.
2-5
Self-Test Rampart Universal Kit
S =) as S
Figure 2-7 RAM Test Menu
Complete ROM Test
The ROM test screen is shown in Figure 2-8. The 0K information appears. If the game has no ROM errors, you see the message ALL ROMS are OK. If the game does have ROM errors, the ROM test screen will remain until the ROM error information is complete. Press the red PLACE button several times to pass the ROM errors, The ROM error test takes a few seconds. See Table 2-6 for the locations of the ROM errors. Press the red PLACE button to return to the test select screen.
Playfield Test
This test, shown in Figure 2-9, checks the condition of the bitmaps in the game. If you see an error on the screen, this indicates an error with the bitmap display Figure 2-9 Playfield Test Screen
circuit. Press the red PLACE button to go to the test select screen.
Motion Object Test
The motion object test screen, shown in Figure 2-10, tests the movement and color of various game objects.
Table 2-4 When to Run the RAM Tests
| ‘Wiese | se | 2 | ~ Location of |
| Problem | Type of Test. | RAMs Tested | |
| Playfield is erratic or | Bitmap RAM". | -8H, 9H, 10H, |
looks wrong Fine “and 11H
Motion objects are not Motion object SN, 6N
working properly ore" RAM* game play is erratic. ©. ° i Color RAM. 4H
esata RAM (once only) isa thorough test, and takes about
Colors look wrong,
| y | E | OKA | tft | 1 minute to run. The “half” tests are significantly | faster, but |
| 6 | rs | Ne | 4p | may not find all pes of errors. |
| 40K | BAB | a0 | EFB | |
| 80 | 9g | 80 | ||
| COK-H | D | Co | 8 | . |
Table 2-5 Bad RAM Locations by
| ALL | ROMS | ARE | O | Error Address |
os Type of RAM Data Bits
| Laie | hare | Playfield RAM“ 200000to | L1H | 0 |
we 21FFFF 10H. A oH. ua 8H 12-15,
| O RETUAN | 10 MENU | Motion Object | 30000 to | oN | 0-7 |
| RAM | _3ESEFF | 5N | §15 |
Figure 2-8 Complete ROM Test Screen Color RAM 3€0000 to agin 3COTFF
2-6
Rampart Universal Kit
Table 2-6 Bad ROM Locations by Error Address
Error ROM Location Error ROM Location
Address High Address low
Program ROM 8x1024 Configuration*:
| OK-H | 13H | OK-L | 13H/) |
| 20K-H | 13H | 20K-L | 13H/J |
| 40K-H | 13) | 40K-L | 13K |
| 80K-H | 13K/L | 80K-L | BL |
| COK-H | 13M | COK-L | 13N |
Program ROM 2x512 and 2x4096 Configuration*:
| OK-H | 13H | OK-L | BHA |
| 20K-H | By | 20K-L | 13K |
| 40K-H | 133 | 40K-L | 13K |
| 80K-H | 13) | 80K-L | 13K |
| COK-H | 13) | COKL | BK |
“If you bave 8x32-pin ceramic parts in column 13 on your Rampart Game PCB, you have an 8x1024 configuration. Uf you have 2x28-pin ceramic parts and 2x32-pin plastic parts in column 13 of this board, you have a 2x512 and (2x4096 configuration.
Select the test function with the left ROTATE button. Use the joystick to move objects, change pictures, change object size, change object palette, and to toggle the horizontal flip. If there is an error, check the motion object ROM at 2N; also check the motion object RAM at 5N and 6N (see the RAM test above). Press the red PLACE bution to move to the next object. Simultaneously press the red ROTATE and red PLACE buttons to go to the test select screen.
Color Test
This test indicates the dynamic range of the video display color circuit. The screen is shown in Figure 2-11. Self-Test
The left side of the screen should be black, with a grey scale changing to white in the middle. The right half of the screen should be red, green, and blue from. top to bottom, each with a color scale from dark to bright, left to right. If the screen does not match this description, adjust the video display as described in the video display manual. Return to the test select screen by pressing the red PLACE button.
Color Purity Test
The color purity test has five screens. Each screen is a solid rectangle of color. The first screen is red. The other screens, which you can see by pressing the left ROTATE button, are green, blue, white, and gray. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Return to the test select screen by pressing the red PLACE button.
Convergence Test
The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-13. To see the violet and green screens, press the left ROTATE button. Press the red PLACE button to go to the test select screen. Check the following on the screens:
Aes
G RETURN TO M
Figure 2-10 Motion Object Test Screen Figure 2-11 Color Test Screen
Rampart Universal Kit
MRSA A Bron ree SHON GGURORNCRE Roe ee SHO Sonne o GoGo pone: Self-Test.
The grid lines should be straight within 3 mm, and the lines should not pincushion or barrel. The convergence of the lines on the violet and white screens should be within 2 mm.
ig eg aa SERED If these screens do not meet these criteria, adjust the video display as described in the video display manual,
Figure 2-12 Convergence Test Screen
2-8
CHAPTER 3
Troubleshooting
and Maintenance
ODUCTION
This chapter contains troubleshooting tables and repair procedures for your Rampart™ game. The chapter has two parts. The first part contains three troubleshooting tables. The tables contain general troubleshooting information, the voltage levels and test points on the game printed-circuit board, and a list of ROM-caused problems, with specific ROMs to check and replace. “ The last part of the chapter has information about connecting the video display Gf it requires separate positive sync) and repair information for the joystick control assembly.
‘Troubleshooting and Maintenance Rampart Universal Kit
Table 3-1 Troubleshooting Table
Problem Suggested Action.
Coin Mechanism Problem
Game Play Problem
Joystick Control Problem
Sound Problem.
Video Display Problem Sync problems.
Screen is dark,
Display area wavers or is too small.
Picture is wavy.
Picture is upside down. Convergence, purity or color problems. Picture is not centered. ~ 9. Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC
10. If the level. is not correct, check the connectors and the harness
. Check the wiring to the coin mechanism. .. Check the voltage to the + side of the mechanism. % . Test the coin mechanisms with the sound test screen in the self -test. . Check the harness and connectors. r Se . Perform the self-test. . Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points.
- Check What ROM Problems Look Like, Table 3-3, for specific ROM problems. NE wre
a . Has the joystick been lubricated with the | correct type of lubricant? If not, lubricate it as shown in Figure 4-2. . Check the harnesses and connectors. . If you took the control apart, have you reassembled it coriectly? z Make sure all the parts on the control are in good repair. Repair or replace pans, wep
Is the speaker volume turned up? Check the voltage on the JAMMA connector. f “Check the wiring from the PCB to the speaker. z a Check the voltage level to the PCB. See Table 3-2, ‘Vollage mpus eed Test Points. . Replace the speaker. Peon
section in this chapter
Is the game plugged in? ~ ; By Is the game turned on? 3 Are the connections good? Is the line fuse good? Is the display brightness turned up? . Are the solder connections on the line filter and transformer good? . Is the JAMMA connector on the PCB tightly connected?”
. Check all of the items below. If you answer “no” to any “question, you have a
problem with the video display, not with the game circuitry, See your video display service manual. : a. Do you have power to the video display? Eat b. Are the video display’s filaments lit? i cc." Do'you have high voltage to the video display? __ i S Aw aoe
ont
or 110 VAC, depending on the type of video display. Video signal voltage i is 0. to 3.5 Volts.) %
‘Do you have correct power voltage to the video display PCB? i Do you have comrect high voltage to the video display? Is the video ground connected to the display? vies om Tae Are the sync inputs connected properly? Does your monitor need a separate positive. sync? See the Video Display Sync Problems section in this chapter. pe
Switch the horizontal or vertical yoke wires on the display. i Use the screens in the self-test to adjust the video display Use. the adjustment procedures in your video display manual. ae
3-2
Rampart Universal Kit Troubleshooting and Maintenance
Table 3-2 Voltage Inputs and Test Points on the PCB
| Voltage | Test Point or LED | Source and Purpose | |
| +5 £0.25 VDC | +5V1 | Logic power from the switching power supply: | ‘ |
CR8 LED Lights when’5 V is applied to the PCB and the reset e (RST) j es is open.
| : | CRS LED | Lights when the +12 V supply is good. | : | E |
| woe | CR4 LED | Lights when the —5 V supply i is good. |
+12V +VOP “412 V from the switching power supply. Positive supply for the analog
| . | (pin 4 of LM324) | circuitry. |
| —5V | ~vop | SV from the switching power supply (if connected). Negative supply for |
(pin 11 of LM324) ~ the analog circuitry. ie
Table 3-3 What ROM Problems Look Like
gee : ay ROM Causing :
| Problem - | the Problem: | Check the ROM at: |
Program works, but the motion, objects or Graphics 2N
playfield are wrong. :
| “Garbage on screen; program doesn't work. | Processor | BC™ | 2 |
| oF game program is erratic, | Program ROM 0 | 13H, E/E |
“No sound or erratic sound. Audio ROM:
| Un | ae | Audio ADPCM | 1D, 2D" |
Video Display Sync
Problems
Some video displays cannot use the composite negative sync that is on the JAMMA connector. The Rampart kit includes a place for a standard Atari Games video connector (not supplied) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video display. For other problems, see the video display manual that came with your game.
Troubleshooting
The tables in this chapter G-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems of
Table 3-4 Atari Games Video Connector Pin Assignments
| Pin: | Pin | Signal | ||
| Le | gets | Doe | S- | GND |
| 2 | 8 | GND | ||
| 3 | 9 | Negative com- | ||
| Ang | <. Green | * | posite sync. | |
| Soe | GND EE | Be | 10 | Positive V sync |
| 6 | Blue" | 11 | Positive H sync |
various parts of the game. The voltage inputs and test points can help you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.
Joystick Controls Routine maintenance of the joystick controls consists mainly of inspecting the roller shafts for excessive wear and periodically lubricating the bearings.
Maintaining the Joystick Maintain the joystick by inspecting the pivot ball, actuator half-ball, and the shaft and by lubricating the joystick with lithium grease.
- Turn off the power to the game.
- Open the control panel and disconnect the harness connector..
- Remove the joystick from the control panel. Use a 3/8-inch wrench to remove the nuts and washers that hold the joystick on the control panel.
- Remove the four long screws that hold the joystick together. See Figure 4-2.
- Take off the 8-position plate, the actuator, and the lower housing.
Troubleshooting and Maintenance
- Check the actuator half-ball, the pivot ball, and the shaft for dirt and wear.
- Lubricate the actuator half-ball on the end of the joystick shaft, the pivot ball below the upper housing, and the spring inside the upper housing. Use lithium grease.
- Put the joystick assembly back together. Fit the pin in the pivot ball into the slot in the lower housing.
- Replace the long screws and tighten them. Do noi over-tighten the screws. The joystick handle must return to center easily.
- Replace the joystick assembly on the control panel.
- Use the self-test to make sure you have reassembled the joystick correctly. Dust and dirt out with compressed air,
Repairs This section includes the procedure for repairing the joystick assembly.
Disassembling the Joystick
Perform the following procedure to disassemble the joystick (see Figure 4-2). 1, Take off the control panel and disconnect the harness connectors. N Remove the joystick from the control panel. Use a 3/8-inch wrench to remove the four locknuts and washers holding the joystick onto the control panel.
- Remove the four screws holding the 8-position plate on the bottom of the assembly. 4, Remove the white plastic actuator and the lower housing that the four switches are attached to.
- Remove the small roll pin holding the actuator haifball on the bottom of the shaft by pushing the roll pin all the way through the shaft. Slide the actuator half-ball off the end of the shaft.
- Remove the large roll pin holding the large pivot ball on the shaft below the upper housing. Push the pin through the ball and the shaft. The pin will not be easy to remove because of the pressure on. the pivot ball from the spring above it. After you push the pin all the way through the ball, slide the pivot ball off the shaft.
- Slide the upper housing off the shaft.
3-4 Rampart Universal Kit
- Slide the plunger and the spring off the shaft.
- Slide the disc off the shaft.
Reassembling the Joystick
- Install the disc on the shaft.
- Slide the spring on the shaft. Push the large end of plunger onto the shaft and over part of the spring (see Figure 4-2).
- Slide the upper housing onto the shaft. 4, Before you put the pivot ball on the shaft, insert the large roll pin partway into the pivot ball. The roll pin should noi interfere with sliding the pivot ball onto the shaft. Slide the ball onto the shaft, and line up the roll pin with the hole in the shaft. Now push the pin through the shaft.
- Put the small roll pin part way into the actuator ball and slide the ball onto the shaft. Line up the roll pin with the shaft hole. Push the roll pin through the ball and the shaft.
- Fit the lower housing over the shaft so that the ends of the large roll pin fit into the slots on the inside of the housing. Turn the lower housing so that screw casings align with the holes in the upper housing.
- Put on the white plastic actuator so that the black cushion ring is opposite the switches.
- Now install the 8-position plate below the actuator so that you can reinsert the long screws.
- Put the long Phillips head screws through the 8-position plate and up through the housings. Do not over-tighten the screws, or the joystick will be too hard to move.
- Reinstall the joystick on the control panel.
ROMs and RAMs
If you have think you have bad ROMs or RAMs, perform the ROM test in the self-test. If you have a ROM problem, see Table 3-3.
CHAPTER 4 ~ Parts Illustrations
INTRODUCTION
This chapter provides information you need
to order replacement parts for your kit. Com-
mon hardware parts, such as screws, nuts,
washers, and so on, are included in these
parts illustrations. When you order parts, give
the part number, part name, the number of
this manual, and the serial number of your
game. @ With this information, we can fill
your order rapidly and correctly. We hope
this will create less downtime and more prof-
it from your games. Atari Games Customer
Service phone numbers are listed on the
inside front cover of this manual.
Parts Ilustrations
o4eass.01 Bezel With Graphics
048879-01 Instructions Label
75-5112B #10-24 x 3/4" Cartiage Bolt (@ places) 177026-0040 #10-24 Nut Washer Assy. (8 places) 175014-1040 #10 Flat Washer| (8 places)
178237005 Blue Button Assy. (4places) 160044-001 ‘Snap-Action Switch (4 places) .4040939-03 ‘8-Position Microswitch Assy. (2 places)
049451-01 Control Panel Decal 04720901 Controt Panel Cover| 04843701 ‘Controt Panel instructions Label 047205-01 Attraction Shield
178237-001 Red Button Assy. (4 places) 160044-001 Snap-Action Switch (4 places) 048453-01 | Attraction Film Rampart Universal Kit
items Not Shown: ‘A046501-01 AMMA Hames Assy. TM-359 Rampart Universal Kit Installation Instructions
04845201 ‘Side Panel Decal | (2 places)
‘A049869-13 Rampart PCB Assy. 178265-001 L-Style Nylon Standott
7551128 +#10-24 x 3/4" Carriage Bolt (4places) {75014-1040 #10 Flat Washer (4places) 17026-0040 #10-24 Nut Washer Assy. (4 places)
Figure 4-1 Parts for Rampart Universal Kit A048475-01 E (4 places) ‘72-6608S #6 x 1/2" Pan-Hd., (Cross-Rec, Type-AB Scrow (4 places)
Rampart Universal Kit Parts Illustrations
4 Lithium Grease
Ball-Shaped Handle and Shaft
Disc
~ I~ Plunger |__ Upper Housing > ‘Assembly
: an) Upper Housing
a ~ Lower Housing |:
‘Snap Action Switch
Actuator
Cushion Ring
Pivot Ball
125" Dia Roll Pin
+#8-16 X-Rec ~ Screw ™~, -086" Dia Roll Pin
8 Position Plate l Actuator Half-Ball
Figure 4-2 8-Position Microswitch Joystick Assembly A040933-03 F
4-4 A048869-07 A Figure 4-3 Rampart Game PCB Assembly Parts Ilustrations
uM
- 2] = ee ta mn BE 6 Ce Gg = Os), O22 eee : ay es EE: Sar gy 8 — aa “ "El 8 eee iar SS os =f ct, : ' Boe = ee ese es = . Lat 5B: =] 8 = 8 sir 8 em a5 ste as so Boss £. 2) tsoz *1F16y Ls24s rare Oe me teh Ba me Be ne es 19} Se
. LS273 ane a7 Ls260 Ls24s HCT273 Ls244 “ee mo) Qi cee BS ee] QL Dm gS gt es $32, Ls24s. Ls2us. 137546-002 = 2
Pe ) : | Ee ext got 8 1532 ar 8 3 psn - sss er ro hi es rsa 85 rasa ee ee ei 7 S136 Ls1eiA F374 F374 1375¥6-002 _Lsas3_ a @ Ls2us Hy = ]@> =] Qo» > «= Qs ar Qa om ry] | un de
on 938 F374 F374 “ou vores
got, = bs ts ee eS] |S S//8|/s : i” *
aa O aD 4/30 is aH
oH
sa
aK Rampart Universal Kit

This page is a drawing, shown as the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Rampart Universal Kit
ARE 1X IF LS245 IS STUFFED.
ALSO, R46 STUFFED, R47 NOT.
Nt
+5uL
Bc eNo2
GND owl MeL WATCHOOG DISABLE
ar— Sot sas
-—i—_o1ms ‘MTG HOLE at
cise ie tt Onto rote
tt Onit9 ove
pe oma MTG HOLE RWS ie n ARTCH
/PARPLELeg@ ue Lso4 i /SWITCH -“ Us3z CRT FF inaooa Schematic Diagrams
FIDUCIAL MARKS FOR
SURFACE MOUNT.
&
nn
's, —
COINCTRLs jay_g
Figure 5-1 Rampart Game PCB Assembly Schematic Diagram 048868-01 F
5-3
Schematic Diagrams ‘Rampart Universal Kit
R94 ERIS RIT 47a. F470 F479 ar N06 USINCOUTS, ay 0-10
cs an /COMPS1N: AVID-9 Ls32 JAM-P
AVIO-11
gusk PVID-8 7crAn——t3]"o12 crn roa
5-4
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Schematic Diagrams
faTcH—l? [+ Rampart Universal Kit
*5VR css #4
| pomo7t6 lop | ggg L326 | a/s0y |
PoMDe—3fo6 pomos—ttlps 50 PCMD422 04 e735 peraa7 Pemo3-t24o3 MsMe295 ate/34 pcHAIE
| PeMo2—ti oe | ais 32 PCMALS | UEP $£@——————_ |
pewo1 2 fo ara Ge PCMALS PCMDI—F 00 aia} 3 PeMA13 Dis 417 ax -22-PCMAL2. 014-4316 nus}? PoMALL i342 415 fio -28- PCMALS
| 012414 | a ST PEMAD | 10. | |
| 01113 | sa Sh pemas | +3V. | ire |
O19ie 97] ‘PCMAT on mx LEL PCMAG 03210 as} PCMAS cno—ss aa PCMR Sq reset pal 2h PCMAa iro Ge peut Gno—des ro 48 PCHAD XT___ xt vss
= e+ NOT STUFFED.
Rampart Universal Kit Schematic Diagrams
cr
+22 AGNO—BGNDs sary-ny CAUD-GNO > BUD-OUTS, jon
cao aie SPKR YS Janet0 Aoog/25y
- SUA aie wiv SRM-F.
| thes | cor | Lees | Lees | Lesz | |||
| azvesy | Pd | [et | Tot | Ted | C74 | C56 | s.c80 |
a SP? GNO-
| thes | C96 | C39 | Let | pcre |
| 47/250 | a | Tat | Pinaoos |
JAMS; = JAM E,
Figure 5-1 Rampart Game PCB Assembly Schematic Diagram 048868-01 F
5-7
Schematic Diagrams Rampart Universal Kit
aan
Rampart Statistics Sheet
Date Recorded: Location:
Meter:
Statistics Screen
Left Coins: Right Coins: Auxiliary Coins: Idle Minutes: 1-Player Minutes: 2-Player Minutes: 3-Player Minutes: New Game Minutes: Continued Game Minutes: Left Player Minutes: Center Player Minutes: Right Player Minutes: Active Minutes: Total Games: Total Sessions: 1-Player Beginners: 1-Player Advanced: Error Count: Total Coins: Average Time/Coin: sec. PTET EEE]
Percentage Play:
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller's plant, and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
eyelet el el elel ele pelted rel ele peeled ele pelea pele felled fel elfelrel el
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
A
ATARI
GAMES
Atari Games Corporation 675 Sycamore Drive Milpitas, California 95036-1110