CATHODE RAY TOMES

Meadows Gypsy Juggler

Gypsy Juggler (Meadows Games, Inc., 1978) · Manual · 41 pages · 33 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

Meadows Games, Ine.

° Telephone (408) 732-8110 National Toll Free (800) 538-1606 181 Commercial Street ° Sunnyvale, California 94086

GYPSY JUGGLER

Manual

For Service/Instructions

Page 3

11.

M1.

v1.

Vii. MEADOWS GAMES INC.

GYPSY JUGGLER _tm

TABLE OF CONTENTS

GENERAL INTRODUCTION

NORMAL OPERATION AND GAME SEQUENCE A. ATTRACT MODE COINS INSERTED INSTRUCTION MODE READY TO START JUGGLING DROP AN EGG (MISS) GAME OVER amooD

SWITCHABLE OPTIONS A. COINS PER PLAYER B. MISSES PER GAME C. INTERMITTENT MUSIC DURING ATTRACT MODE D. EXTENDED PLAY (EXTRA MISS)

GYPSY JUGGLER CONTROL PANEL A. DESIGN B. TO OPEN PANEL C, TO REMOVE PANEL D. TO REMOVE

  • | PUSHBUTTONS
  • SWITCHES
  • POT CONTROL

REMOVE MONITOR

REMOVE MICROPROCESSOR LOGIC BOARD

REMOVE MICROPROCESSOR AUDIO BOARD PA

WWHHN—

Pree

nn VV uMVn uunnw GE(S)

an

Page 4

VIII.

IX.

XI.

XII.

XIII,

XIV.

XV. REMOVAL OF POWER SUPPLY

REMOVAL OF ATTRACT PLEX

REMOVAL OF FRONT PLEX

INTERLOCK SWITCH, FUNCTION OF:

AUDIO ADJUSTMENTS

AUTOMATIC ROM/RAM SELF-TEST

OVERSEAS OPERATION - VOLTAGE REQUIREMENTS

WARRANTY RETURN AUTHORIZATION (RA) POLICY

LIST OF ILLUSTRATIONS SWITCHABLE OPTIONS, OPERATOR ADJUSTABLE CABINET DRAWING, W/MARKED DESIGNATIONS CABINET DRAWING, (FOR TV, PLEX, CONTROL PANEL LOCATIONS). GAME SCHEMATICS RECOMMENDED SPARE PARTS LIST

MOTOROLA SERVICE MANUAL MEADOWS GAMES INC. GYPSY JUGGLER TABLE OF CONTENTS Page -2-

PAGE(s

Page 5

MEADOWS GAMES INC. GYPSY JUGGLER tm MAY 1978

  • GENERAL

Meadows GYPSY JUGGLER is a1, 2, 3, or 4 player game where players compete for high score against opponents or against themselves. High skill factor; takes a second to learn GYPSY JUGGLER, and a lifetime to master. Invites replay for higher score.

Objects being juggled are eggs served by the player to the juggler figure on the screen by pressing ''ADD~ANOTHER-EGG!' button. Add more eggs (maximum 4) and your score zooms up. legg=5 points, 2=50 points, 3=100 points, 4=200 points. No score for bouncing egg off the jugglers head.

Misses (dropping an egg), operator adjustable 2-9; a ''peeping'! chicken pops out of broken egg and exits off the screen in shortest direction.

Eleven separate sound effects accompany juggling. Intermittent theme music during attract mode is operator option.

Other features on this sensational new fun and skill GYPSY JUGGLER include: Separate volume control for game sounds and music; coinage options including Free Play for showroom demo and trade shows; credit accumulator to 99; external ON/OFF switch; Hi Score For the Day; 3-position interlock switch inside back door; slide-out step; automatic ROM/RAM SELF TEST.

1 NORMAL OPERATION AND GAME SEQUENCE

A. ATTRACT MODE When GYPSY JUGGLER is first powered up, the game attract mode is displayed on the screen; the computer playing the game exactly as the game should be played.

Information displayed on the T.V. screen during the attract mode is:

TODAYS H! SCORE = XXXXX GAME CREDITS=XX MISSES LEFT= X

PLAYER 1= PLAYER 3= PLAYER 2= PLAYER 4=

Directly under the juggler figure, in the attract mode, intermittently flashing,

is the message:

INSERT COIN 1 COIN PER PLAYER

OTHER COIN OPTIONS AVAILABLE ARE:

1 COIN = 2 PLAYERS 2 COIN PER PLAYER FREE PLAY

Page 6

MEADOWS GAMES, INC. GYPSY JUGGLER MAY 1978

"FREE PLAY" coin option specific design and purpose is to enable the game to be put into this mode for showroom demonstration or exhibit/trade show demonstration, and eliminating the necessity of having to leave the coin door open for access to the coin acceptor or affix an external free play button. When GYPSY JUGGLER is used in FREE PLAY, 4 game credits are always given. All 4 credits must be played before game will go back into attract mode.

Another feature included in the attract mode, (operator selectable), is one chorus of theme music, Thunder and Blazes a.k.a. (Entry of the Gladiators), which will play one chorus approximately every 4 minutes. One chorus lasts approximately 20 seconds. The volume for intermittent music during attract mode can be controlled and adjusted separately from the other sound effects that accompany the game during play.

B. COINS INSERTED When coins have been inserted, GAME CREDITS will indicate the number of credits (i.e. = 01). A series of 3 ''gong'' sounds accompany insertion of each coin. The attract mode stops immediately as soon as the first coin is inserted, and the ''Instruction'' mode appears on the screen. The MISSES LEFT will also indicate the number of misses the game is set for by the operator, (i.e.= 5) (Can be set at 2 to 9 misses).

C. INSTRUCTION MODE

All information on the top quarter of the T.V. will remain. In the area where the juggler figure appeared, the processor will write:

SEE CONTROL PANEL FOR INSTRUCTIONS

SCORE XXXXX FOR EXTENDED PLAY (*)

One chorus of The Volga Boatmen will play during the attract mode. One chorus lasts about 8 seconds. The instruction mode and 8 second chorus will be terminated immediately when PLAYERS button is pressed.

(*) EXTENDED PLAY message will appear during the attract mode only if the operator selects this feature. XXXXX indicates the minimum score to be achieved and is operator selectable at 5,000; 15,000; or 35,000 points per player. EXTENDED PLAY is one additional miss during that players turn.

D. READY TO START JUGGLING

As indicated on the control panel ''INSTRUCTIONS'', each player must press ''PLAYERS'' button. When the players press PLAYERS button, 00000 is displayed to the cooresponding players in a very rapid succession and

Page 7

MEADOWS GAMES GYPSY JUGGLER MAY 1978

this procedure, too, is accompanied with sound effects. Putting players into play is accomplished in exactly the same manner as pinballs.

Player 1 score area begins to flash indicating Player 1 up. The Jugglers legs are moving and he can be moved freely left and right on the T.V. screen.

The player should locate the man directly under the chute and serve the first egg by pressing ''ADD-ANOTHER-EGG'' button. Juggling has begun by passing the egg from one hand to the other. For the first egg, each time the egg is Juggled from one hand to the other, 5 points are added to the players score.

When the second egg is added by pressing ''ADD-ANOTHER-EGG'' button each successful hit adds 50 points to the players score. Please note that for best results and higher scores, each time one egg is added, the Juggler figure should be under chute. For the third egg put into play, each hit Is worth 100 points; forth egg in play and hit is worth 200 points every time successfully juggled from hand to hand.

E. DROP _AN EGG

When an egg is dropped (MISS), there is an accompanying "splat! sound. A chicken pops forth out of the egg and goes "peeping'' off the screen in the shortest direction. The broken egg from which the chicken emerged remains visible on the screen until the next player ''ADDS-AN~EGG'' and starts juggling.

For each miss, the ''MISSES LEFT! decreases by one. ''NEXT PLAYER'' is atso written across the T.V. screen. These events occur until all "misses" are used up by the players.

F. GAME OVER

After all players have used the designated number of misses, ''GAME OVER'! is written across the T.V. screen and remains written on the screen for about four seconds. The game will automatically play one chorus of ''Thunder and Blazes''. ''GAME OVER'' message will disappear from the T.V. after the four se~ cond period and then the game will automatically go into the attract mode.

If a game credit remains on the game after ''GAME OVER'', the game will sequence its four second message and music for ''GAME OVER'' and then instantly go into Instruction Mode, playing its one chorus of The Volga Boatman.

All scoring information remains on playfield at completion of game if all credits are used. If credit(s) remain at completion of games just played, all information Is eliminated except TODAYS HI SCORE and GAME CREDITS.

Page 8

MEADOWS GAMES INC. GYPSY JUGGLER tm MAY 1978

111, SWITCHABLE OPTIONS (See Page ga )

A.__COINS PER PLAYER

COINAGEswh‘SWS,
1 coin per playerONON
1 coin = 2 playerOFFON
2 coins per playerONOFF
FREE PLAYOFFOFF

B. MISSES PER GAME

#MISSESSWISW2,SW3
2ONONON
3OFFONON
4CNOFFON
5OFFOFFON
6ONONOFF
7—OFFONOFF
8ONOFFOFF
9OFFOFFOFF

C. INTERMITTENT MUSIC DURING ATTRACT

sw6 ON OFF OFF ON

D.__ EXTENDED PLAY (EXTRA MISS) SW7. SWB

NO EXTENDED PLAYONON
5,000OFFON
15,000ONOFF
35,000OFFOFF

tf extended play Is selected by the operator, this will be indicated to the player during the "Instruction Mode''. To reiterate, the extended play message during Instruction Mode reads: ''SCORE XXXXX FOR EXTENDED PLAY''; (XXXXX being the level of score the operator has chosen from D. above).

When the player reaches this score level while playing the game, a series of "gongs'' will be heard and the message ''SAME PLAYER PLAYS AGAIN'' will be written in the solid yellow area under the juggler constantly until a 'miss!'' occurs during that play. When the egg is dropped the egg splats ; the chicken exits the T.V. screen and the identical message ''SAME PLAYER PLAYS AGAIN" is written again across the middle of the T.V. The extended play is therefore indicated in ''MISSES LEFT'' area and does not decrease by one. For instance, if "MISSES LEFT" shows 3 and extended play is reached, ''MISSES LEFT" will still indicate 3 at the end of that players turn. Additionally the player number (1,2,3, or 4) will continue to flash as further reminder that it is still this players turn.

he

Page 9

MEADOWS GAMES INC. GYPSY JUGGLER tm MAY 1978

IV. GYPSY JUGGLER CONTROL PANEL

A. DESIGN GYPSY JUGGLER control panel has (2) pushbuttons and (1) clutch potentiometer (pot) control knob. One pushbutton, PLAYERS, is for putting the number of players into the game. The other pushbutton, "'ADD-ANOTHER-EGG'' is used for the purpose of adding eggs to be juggled to the juggler. The clutch pot control is designed to move the juggler from left to right on the T.V. screen.

The control panel is covered with MEADOWS new '' texture-tuf, scratch resist, perma-print control panel".

B. TO OPEN PANEL . Unlock and open coin door. Reach through coin door and remove wing nut and washer from the left and right side of the control panel. Pull panel ; out from front plex. Panel is hinged to the cabinet and therefore has a built-in 'stop' when flipped out from the cabinet.

c. TO REMOVE PANEL To remove the panel, follow procedure described in B above. Remova], however, should not be necessary. When the panel is open, remove all wiring from the (3) switches and tuck the wiring back inside the cabinet to keep out of your way. Remove hex nuts, washers and carriage bolts from back side of hinges. The complete panel can now be removed.

Dd. TO REMOVE PUSHBUTTONS, SWITCHES, POT CONTROL

  • Pushbuttons (MEADOWS p/n 051-0029) With panel open, disconnect switch. Remove large nut from back of pushbutton. Remove pushbutton by lifting off from top of control panel.
  • Switches Cherry p/n E2350K (MEADOWS p/n 051-0016) Disconnect switch. Remove (2) 4-40 hex nuts, washers and machine screws. Remove switch and replace.
  • Pot Control (MEADOWS p/n 043-0014) Pot Control is a 5K clutch pot. With the control panel in closed position, remove Black knob (MEADOWS p/n 091-0070) with a small screwdriver or hex driver, as applicable. Now open control panel and remove (3) wires. Using your fingers, grasp pot firmly and from the outside surface of the control panel, remove the nut and washer from the pot with the use of pliers or nut driver.

V._TO REMOVE MONITOR

1.

2.

3. Turn ON/OFF TOGGLE SWITCH located on top back of cabinet to ''0FF''. (See pg.)

Disconnect power cord from AC outlet.

Remove cabinet back door.

Page 10

MEADOWS GAMES GYPSY JUGGLER MAY 1978

4, Remove and set aside (4) hex nuts and washer from underside of wooden TV mounting shelf.

  • Remove (4) carriage bolts from shelf.
  • Remove front plex. (Refer to page 7).
  • Remove nuts and machine screws from each upper corner of TV chassis brace mounted into wooden support blocks.
  • Grasp frame and TV firmly with both hands and remove TV from front of cabinet opening. SPECIAL NOTE: Manufacturer recommends front removal of TV; however, TV can be removed throught back door.

VI. TO REMOVE MICROPROCESSOR LOGIC BOARD 1, Turn ON/OFF toggle switch located on top back of cabinet to "OFF". 2, Disconnect power cord from AC outlet.

  • Remove back door of cabinet.
  • Logic board is located on the right side of the cabinet as seen from the back door. Remove #6 sheet metal screw, 5, Disconnect (2) edge connectors.
  • Slide board out from slotted cleat.

VII. TO REMOVE MICROPROCESSOR AUDIO BOARD

  • Turn ON/OFF toggle switch located on top back of cabinet to "OFF".
  • Disconnect power cord from AC outlet,
  • Remove back door of cabinet, 4, Audio board is the smaller board located on the left side of cabinet as seem from back door. Remove #6 sheet metal screw.
  • Disconnect (2) edge connectors.
  • Slide board out from slotted cleat.

VIII. REMOVAL OF POWER SUPPLY (IF_NECESSARY)

  • Turn ON/OFF toggle switch located on top back of cabinet to "OFF".
  • Disconnect power cord from AC outlet.
  • Remove cabinet back door.
  • Power supply is located on the floor of the cabinet.
  • Disconnect mal e and female 9-pin Molex connector that connects the power supply and main harness.
NOTE: DO NOT REMOVE 115/230V converter plug.

Re Remove (4) sheet metal screws located at each corner of this

assembly.

  • Remove from cabinet.
  • Refer to schematics for service. (Page 14).
Page 11

MEADOWS GAMES INC, GYPSY JUGGLER MAY 1978

IX. REMOVAL OF ATTRACT PLEX

  • Open cabinet back door.
  • Located on inside ceiling of cabinet, find 1/2" wide, flat security bar.
  • Loosen slightly the Phillips screw, (suggest 1/4 turn). 4, Pull straight back on security bar releasing attract plex.
  • Move to front of cabinet and carefully lift plex out from cabinet. (A small screwdriver can be used for removal, or plex can be removed without the use of tools - by hand).

X. REMOVAL OF FRONT PLEX

  • Open control panel. (See Section IV., B., Page 5).
  • Push "up" on lower center of plex.
  • Remove by pulling up and forward on plex.

XI. INTERLOCK SWITCH, ‘FUNCTION OF: (Inside Back Door)

  • Door ON, game powered, provided plugged into AC outlet.
  • Door OFF, AC power automatically shut off.
  • To service or troubleshoot game when back door removed, pull Interlock Switch OUT to fullest extension.

XII, AUDIO ADJUSTMENT

GYPSY JUGGLER has two (2) volume control pots (found on the Audio PCB) to regulate the game play sounds from the music sounds during ATTRACT MODE. Please refer to Page 10 for location and function of volume controls.

XIII. AUTOMATIC ROM/RAM SELF-TEST

Upon powering up GYPSY JUGGLER, the microprocessor will clear the screen to all white (not visible if monitor is not warm), which will show any defects in the screen display circuitry. After about one or two seconds, the microprocessor will attempt to exercise the "RAM" circuits. If there is a failure in the RAM, the screen will flash “RAM FAILED" in a dark rectangle in the center of the TV, and then the microprocessor will begin the automatic ROM/RAM test all over again,

If the RAM's are good, then the microprocessor will examine all of the program ROM's to verify they are working and that the program is good. If the ROM test fails, the words "ROM FAILED" will flash on the TV in a dark rectangle in the center of the screen, and the automatic ROM/RAM test will be started over again.

Due to warm-up time, the RAM's or ROM's may fail to pass the automatic ROM/RAM test once or twice. If this happens and the game starts normally, then the failure was temporary. If there is a ‘real’ failure, the words in the rectangle will continue to flash indefinitely.

Page 12

MEADOWS GAMES INC. GYPSY JUGGLER MAY 1978

XIV. OVERSEAS OPERATION - VOLTAGE REQUIREMENTS

For overseas operation of GYPSY JUGGLER requiring operation at other than 115V, please refer to:

  • IV monitor - slide switch located on bottom left side marked: "VOLTAGE", (See MOTOROLA SERVICE MANUAL, Section XVI).
  • Nine-pin connection located at power supply on cabinet floor. Make connection at end labeled 230V.
  • On models built by the manufacturer for overseas operation, an additional "Step-Down Transformer" has been installed between the AC power cord and the light fixture. If you plan to ship your game to a location where 230V only is available, a Step-Down Transformer is REQUIRED. DO NOT attempt to power up at 230V without a transformer. If you need this transformer, a Stancore, P/N P6820, or equivalent, (MEADOWS P/N 050-0017) can be used.

WARRANTY

Contact the distributor from whom your game was purchased for warranty and/or service information.

NOTE: ALL EQUIPMENT RETURNED TO THE FACTORY MUST HAVE A RETURN AUTHORIZATION NUMBER, ISSUED BY MEADOWS GAMES, INC., AND TRAVEL FREIGHT PREPAID. TO ASSIST YOURSELF IN EXPEDITING THE RETURN OF ANY ITEM TO BE SERVICED, PLEASE BRIEFLY LIST SYMPTOMS OF MALFUNCTION. YOUR COOPERA- TION IS GREATLY APPRECIATED.

GOOD LUCK AND ENJOY THE MANY PROFITS OF OWNING AND OPERATING ---- MEADOWS GAMES "GYPSY JUGGLER".

Page 13

é = 2 5 = = = Vay LOGIC Pcp MISS {

OPTION

[or fe Tor fo [for for

gGOWN ek | COIN e COINS FREE DON

COIN

B PLAYER

OPTION | oO ?

GYPSY JUGGLER +,

OPERATOR SELECTION

SulTCk OPTIONS

MUSIC

(arrract) ° NONE 500c i§08¢ 35,006

OPTION SWITCH

MEADOWS GAMES , INC.

Page 14

MEADOWS GAMES INC GYPSY JUGGLER tm MAY 1978 i enpeereeasianie

4 ATTRACT PLEX LOCK LOGIC PCB

ON/OFF TOGGLE SWITCH

“OPERATOR OPTION'' SWITCH

INTERLOCK SWITCH

POWER SUPPLY

“SLIDE QUT" STEP, (EXTENDED)

ATTRACT MUSIC VOLUME CONTROL

~-10-

Page 15

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

MEADOWS GAMES INC.

GYPSY JUGGLER SPARES LIST

023-0069Sound PCB085-0031Panel Hinge

027-0066 Power/Light Harness 027-0063 Ground Harness 027-0067 115/230. Volt Adapter

PART NUMBERJ sesamin| | arr ncn |DESCRIPTION
012-0012ieeeee ON/OFF Switch
012-0175| coin poor assy| |osi-ons | Interlock Switch

amansanninraeiiirnen 3

016-0121J warning tabet| |ot6-0133 | Panel Overlay Texter-Tuf

916-0131 _ [To eront rex | [sions Red Prshiourton

023-0068oeee Black Control Knob

fonts [rower /ighe Harness || ee ee ae | eee 027-0065 Main Harness

~13—

Page 18

Tt Z 0 1 133s] 3WoS "Duunywa 3185 10N 00 7 | 8900 sz0 | a smal aw “on Dmvaivad | (on 13013009 | 3715 | ef [ D2799NL ASAD a Qyveg sauye oe OM aI Om IES t

b i s rr Sy Do an 7 i sypayswwwi23 “ONL ‘SAWYD BMOQVaW. tx 3 fa wsone mn seth -2/o- ser fe e08y - paar oy 21 sty — AG ato usney x ama oe or sony Segal —plovo¥ & snoy — oq avov ssoov

£4 wil es 82 gor wore tseay 1 sony — Pau secon ye 2202 FF a asnas, eh te tl at oo a nae ops af 5y| eve + we wt tele “ who 9019 10 29 0 #019 10 400 O30/K ‘yer7en waren was aroin canis wonata3630 cg

Page 19

mov enak or mene 193

seme ri myer 5”

‘PEAK ano CEBURR SIUSRARY ces MAK, | waTERAL NSH rye MEADOWS GAMES, INC.

GAME BOARD GYPSY FUGCGCLER MALS ANGLES ce ed

TE] CODE DENT NO. | ANG nO,

Page 20

feny FameD

be 4 pavsy sig Ea—teane paves Segue) eer a

208° aa veer

ara ra pe

oy v % cree a —it{ ontea

ON suGhlen omen #8.

bese

oy SEHEN3 OWE ARE nos, NCES A

coal MEADOWS GAMES

PROGRAMA BLE AUDIO BORD GYPSY TJVGELER

TYE ] COOP GENT WO. BaAWINERG, ols -00 6F

‘DONOT SCALE ORAWING,

Page 21

No VOLT Plug

VOLT SELECT 28V.CT lata INTRICK & sw S&

LAMP

oFF/on

@ ramps aa{” MONITOR Le WHT $0 ye RIK -3—1 P

joa hes ANT _Y 74-5 - 34 3 8 COIN SWITCH #1 mate 83 $3 [pil — s4-¢—§ —— 3-8: p so-a———o \p, CON swiTCH #2 wrax——_J* cal

¢ [ins e SI Pavers }—— 3 ‘ [| Al =) on [pL — s1~3_—__—. |_ ——ra-a. n Az- bps =R\ o_o | = MAN MOVEMENT ContRol $2 DROP EGG

Harness piacram

Oussler

NONE { SDUNDO B-2 22 Ba F Peace Zon

w/e cid Qlw 5/3 ais = UV Ls NX Fe

A219 sac op Annis ee

226-2010

H A

Page 22

MOTOROLA

Service Manual

FAEPC 00399 Model M5000/M7000 Series Monitor

CAUTION NO WORK SHOULD BE ATTEMPTED ON ANY EXPOSED MONITOR CHASSIS BY ANYONE NOT FAMILIAR WITH SERVICING PROCEDURES AND PRECAUTIONS.

GENERAL INFORMATION

This manual contains information on the M5000/M7000 monitor series, the optional KV800A audio module, and the +5 volt logic power supply. The M5000/M5010 series use a 19-inch CRT and the M7000/M7010 series use a 23-inch CRT. All CRT’s are of the magnetic deflection type with integral implosion protection.

The M5010/M7010 series incorporates the adjustable +5 volt logic supply for external logic circuitry, and the optional audio module. The monitor series is capable of providing power for external audio modules to reproduce monaural or stereo sound. The monaural and stereo input signals are applied to the 12-pin connector located at the rear of the chassis. A 3-pin output connector is provided at the rear of the chassis for each audio module.

All monitor power supplies are capable of producing both +73 volts and +12 volts regulated from either 115 DATA PRODUCTS

MODELS M5000-155 M7000-155 M5010-155 M7010-155 KV800A- auDio MODULE *

AVAILABLE OPTION

KV800A - Audio Medule*

volt or 230 volt AC input to the transformer primary. All monitor variations described herein require a composite video input signal.

Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire. The outputs consist of +5 volts regulated (12-pin connector), and +73 volts regutated and audio (3-pin connector).

All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one-stage blanking amplifier; and a regulated, full-wave bridge, power supply. The table below describes the associated functions and optional equipment that is available for each monitor.

MODEL BREAKDOWN CHART

VIDEO INPUT +5 VOLT SUPPLY

5000-155 MS5019-155 COMPOSITE COMPOSITE (FACTORY OPTION) | (AVAILABLE OPTION) 19" CRT | 23” CRT

x

M7000-155 M7010-155 COMPOSITE COMPOSITE x a x x

& MOTOROLA Data Products _ caro.stream, iLunols 60187 PART NO. 68P25253A47 6/77 PRICE $2.20 COPYRIGHT 1977 BY MOTOROLA, INC. PRINTED IN U.S.A,

Page 23

SAFETY WARNING

CAUTION: NO WORK SHOULD BE ATTEMPTED ON AN EXPOSED MONITOR CHASSIS BY ANYONE NOT FAMILIAR WITH SERVICING PROCEDURES AND PRECAUTIONS.

1, SAFETY PROCEDURES should be developed by habit so that when the technician is rushed with repair work, he automatically takes precautions.

2, A GOOD PRACTICE, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.

  • Extreme care should be used in HANDLING THE PICTURE TUBE as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). Do not nick or scratch glass or subject it to any undue pressure in removal or installation. When handling, safety goggles and heavy gloves should be worn for protection, Discharge picture tube by shorting the anode connection to chassis ground (not cabinet or othér mounting parts). When discharging, go from ground to anode or use a well insulated piece of wire. When servicing or repairing the monitor, if the cathode ray tube is replaced by a type of tube other than that specified under the Motorola Part Number as original equipment in this Service Manual, then avoid prolonged exposure at close range to unshielded areas of the cathode ray tube. Possible danger of personal injury from unnecessary exposure to X-ray radiation may result.

4, An ISOLATION TRANSFORMER should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also protect the chassis and its components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

  • Always REPLACE PROTECTIVE DEVICES, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
  • If the HIGH VOLTAGE is adjustable, it should always be ADJUSTED to the level recommended by the manufacturer. If the voltage is increased above the normal setting, exposure to unnecessary X-ray radiation could result. High voltage can accurately be measured with a high voltage meter connected from the anode lead to chassis.
  • BEFORE RETURNING A SERVICED UNIT, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without
danger of electrical shock. DO NOT USE A LINE ISOLATION TRANSFORMER WHEN MAKING THIS TEST.

in addition to practicing the basic and fundamentai electrical safety rules, the following test, which is rv lated to the minimum safety requirements of the Underwriters Laboratories should be performed by the service technician before any unit which has been serviced is returned.

we 1000 OF M/VOLT (OR HIGHER) AC VOLTMETER, NOTES: 1. REPEAT EACH CHECK WITH THE LINE CORD

REVERSED IN THE POWER QUTLET

  • METER READING MUST NOT EXCEED TA VOLTS ac. “MOT” LEAD OF METER TO EACH

EXPOSED PART OF CABINET

AS WELL AS THE CABINET,

GROUND LEAD OF METER TO ANY EARTH

GROUND SUCH AS. COLD WATER PIPE Ny

1500 OHM 10 WATT RESISTOR INSULATOR, Au

Voltmeter Hook-up for Safety Check

A 1000 ohm per volt AC voltmeter is prepared by shunting it with a 1500 ohm, 10 watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.

The AC voltage indicated by the meter may not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and “earth” ground. Such a unit represents a potentially serious shock hazard to the operator.

The above test should be repeated with the power plug reversed, when applicable.

NEVER RETURN A MONITOR which does not pass the safety test until the fault has been located and corrected.

Page 24

ELECTRICAL SPECIFICATIONS*

MODELS: MODELS:

M5000-155/M5010-155 M7000-155/M7010-155

19" measured diagonally (48.2 cm); 184 sq. 23’ measured diagonally (58.4 cm); 282 sq, inch viewing area (1188 sq. cm); 114° de inch viewing area (1820 sq. cm); 110° deflection angle; integral implosion protection; flection angle; integral implosion protection; P4 phosphor standard P4 phosphor standard

POWER INPUT: 115/230V AC, 110 Watts (nominal); 60 Hz provision for 230’ AC, 50 Hz

FUSES: MS000-155, M7000-155 — 0.8A; M5010-155, M7010-155 — 1.04

+73 VOLT SUPPLY: Electronically regulated over AC inputs from 103V AC to 130V AC, or 206V AC to 260V AC : PICTURE TUBE:

VIDEO INPUT 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT

RESOLUTION: 500 lines at picture center

LINEARITY: Within 3%, measured with standard EIA ball chart and dot pattern

HIGH VOLTAGE 17KV (nominal)

HORIZONTAL BLANKING INTERVAL 11 microseconds typical (includes retrace and delay)

SCANNING Horizontal: 15,750 Hz +500 Hz; Vertical: 50/60 Hz FREQUENCY:

ENVIRONMENT: Operating temperature: 10 °C to 55° C (ambient)

Storage Temperature: —40 °C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 (electronic components)

TYPICAL 14.11” H, 18.18” W, 14.83” D 16.72” H, 21.56" W, 16.18” D DIMENSION (35.8 x 46 x 37.6 cm) (42.4 x 54.7 x 41 om)

AVAILABLE OPTIONS*

AC INPUT

DC INPUT Derived from +73 volt output in monitor power supply for reference amplifier.

DC OUTPUT +5V DC @ 3A adjustable, +. 5% regulation.

*Specifications subject to change without notice. +5 VOLT LOGIC SUPPLY

Derived from separate winding in monitor power transtormer.

Page 25

AVAILABLE OPTIONS*

KV800A AUDIO MODULE

DC INPUT: +73 volts required, supplied from M5010/M7010 series monitors or external power source.

AUDIO INPUT: (Each Channel) O.5V for full output accessed through 12—pin connector.

AUDIO OUTPUT : Linear 1.0 Watt (Nominal)

MECHANICAL: 4’ PM speaker, integral volume control, 4 ft. cable (120 cm) provided for remote installation with M5010/M7010 series monitors.

ENVIRONMENT: Operating temperature: 10° C to 55 °C (ambient). Storage temperature: —40 °C to +65°C. Operating altitude: 10,000 ft. maximum (3048 meters) CSA certified for use in coin-operated amusements in a combustible enclosure , UL listed under specification 1410 (electronic components).

  • Specifications subject to change without notice.

SERVICE NOTES

CIRCUIT TRACING

Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, contro! names are also shown and teferenced on the schematic diagram in this manual.

Transistor elements are identified as follows:

E — emitter, B—Base, and C- collector.

COMPONENT REMOVAL

Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.

It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.

The nozzle of the solder extracting gun is inserted directly cover the component lead and when sufficiently heated, the solder is drawn away leaving the lead free from the copper foil. This method is particularly suitable in removing multiterminal components. CRT REPLACEMENT

Use extreme care in handling the CRT as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.

  • Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
  • Remove CRT from the front of the chassis by loosening and removing four screws; one in each corner of the CRT.

ADJUSTMENTS

A non-metallic tool is recommended when performing the following adjustments.

REGULATOR ADJUSTMENT

=—— NOTE =

Misadjustment of the +73 volt regulator, or the horizontal oscillator may result in damage to the horizontal output transistor or pulse limiter diode. The following procedure is recommended to insure reliable operation.

Page 26
  • Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
  • Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service,
  • Adjust HOR. SET coii L1 until display is stable.
  • Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 volt test point.

5, Adjust the 73V ADJUST. control, R93, for an output of +73 volts. DO NOT rotate the control through its entire range; damage to the monitor may result.

  • When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.

HORIZONTAL HOLD/OSCILLATOR ADJUSTMENT

Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical, or the CRT display is stable (synced).

+5 VOLT SUPPLY (OPTIONAL)

  • Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
  • Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q201, or any +6 volt test point.
  • Adjust the 5V adjust control, R206, for an outout of +5 volts.

4, When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation.

VERTICAL HEIGHT/LINEARITY ADJUSTMENT

1, Connect a test generator whose output is similar to the display signal normally used.

  • Rotate the vert. size control, R6O, until the smallest display is obtained.
  • Adjust the vert. lin. control, R64, until the top and bottom of the test pattern is equally spaced.
  • Re-adjust R6O until the desired display height is obtained. 5, Re-adjust R64, if necessary, as in Step 2 above.

FOCUS ADJUSTMENT

The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus at a point which is near the center and approximately 1/3 down from the top of the display.

MONITOR SERVICING

The monitor circuit board or the +5 volt supply circuit card may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see views below).

Monitor Circuit Board in Service Position +5 Volt Supply in Service Position

Page 27

COMPOSITE VIDEO (NPUT

CHAN. AUDIOIN

(CHAN, 2 AUDIO IN «——

sync sync. ‘SEPARATOR AMI

uss no. cere-00422-0 Block Diagram

THEORY OF OPERATION

POWER SUPPLY

The power supplies are transformer operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.

+73 VOLT SUPPLY (See Figure 1.)

When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (Pin 6) to increase the forward bias of 019. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage will cancel the attempted output voltage increase.

When the +73 volt supply buss attempts to decrease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19, The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series with the output, will decrease proportionally to the attempted decrease in the output buss.

Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within the device. Resistor R82 is the current limiting resistor for Q18 and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of IC1, and C49 is a Miller effect capacitor which efiminates instability, Capacitor C32A filters horizontal frequency variations from the output buss.

Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output buss, back to pin 3 preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature compensate for variations within D21. Capacitor C32B filters AC variations from the output of the full-wave bridge.

Page 28

FIO PL ~T fi Ce 4 Ql7 ABW we “1 REGULATOR mc. 8S,

' siPzFL3

foctae tg 1 rat

Ag rOWERLow | ye tomOBA.

SOU ran mes

INPUT.time |boner a

8 EO ee

!7a
a3) 2FaQl? BE
. |Isl=omREG. BUFFER

2 a cue.

ee ae) Tana

Figure 1.

+5 VOLT SUPPLY (See Figure 2.)

The +5 volt power supply is a simplified form of the +73 volt supply in that it uses a series pass regulator output and a zener diode reference source on one input of the integrated circuit reference amplifier. This supply uses one less stage for voltage regulation. Therefore, the reference voltage is connected to pin 3 instead of pin 2, as in the +73 volt supply.

When the output of the supply attempts to increase, the voltage at pin 2 of IC1 will increase and disturb the balanced condition at the inputs of the reference amplifier. The output voltage at pin 6 of IC1 will decrease causing the forward bias of Q202 to decrease. Transistor Q202 will conduct less and therefore, less base current will be supplied to 201 via the emitter of 0202. A greater voltage will be present, from collector-to-emitter across 0201, which is directly proportional to the attempted increase in output voltage.

When the output voltage of the supply attempts to decrease, the voltage at pin 2 of IC1 will decrease and disturb the balanced condition at the inputs of the reference amplifier. The output voltage at pin 6 of IC1 will increase causing the forward bias of Q202 to increase,

Transistor Q202 will conduct more and therefore, more base current will be supplied to Q201 via the emitter of 202. A smaller voltage will be present, from collectorto-emitter across Q201, which is directly proportional to the attempted decrease in output voltage.

Capacitor C201 filters line frequency variations from the output supply buss. Resistor R201 provides base bias voltage for 0202 and R204. Resistors R202 and R203 provide the operating voltage for IC1. Resistor R205 establishes the operating current for D202.

The zener diode provides a constant reference voltage for pin 3 of IC1. Capacitor C202 is a Miller effect capacitance which eliminates instability. Resistor R206 sets the 5 volt bias voltage for pin 2 of IC1.

REGULATED 9204 7634 WEAT SINK MOUNTED) ‘AC INPUT + FROM SEC. >-—— To PING OF P4 FMA TS. + REGULATED. ¢203 +5.0V AT 3.08 400 — OUTPUT = LO Termsoree REF. AMPL. t5v = \C204 S3F REG. ADJ.

ion, f M, “ARD L o 4/4aWw

Page 29

+73V +150V

R2 i P/O 33K PL Ql AGH EMITTER oomeoo 1 FOLLOWER INPUT

VIDEO AMPLIFIERS AND OUTPUT (See Figure 3.)

The composite video signal is coupled to the emitter follower Q1 through the input connector P1 and capacitor

C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifier and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the syne separator Q10 through C33 and, to the contrast control R6 through C47.

The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct coupled common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high frequency peaking. Qs Ble VIDEO OUTPUT

DRIVER 27v CB zzope 022 =S VIDEO ‘All TO PIN 7 (CATHODE) = OF V1 (CRT) VIA R78

To Q10 EMITTER Tog COLLECTOR Figure 3.

The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the syne amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7 and C8, and resistor R16, are used for high frequency compensation. Diode D22 is used for temperature compensation and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2 and, R19 and D4 are used to limit the current through the CRT. Capacitor C10 AC couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5 and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and a3.

Page 30

Q7 P2s HORIZ PULSE SHAPER ay R Q8 ASF WORIZ DRIVER 4.59, Q6 AbL HORIZ OSC gag £ a aI BASE

gn as]|aa.av1 Fx
47K:P26:1e
10 be 5c20R30Bgpc21

1K =o

825“*cool7
R24S3,3KolTe
150K Puan1=R37IC23

two > e3zo[t

aoaol,R3410
coosOLEr Acers

HORIZONTAL DEFLECTION CIRCUITS (See Figure 4.)

PHASE DETECTOR

The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base. The horizontal output (Q9) coliector pulse is integrated into a sawtooth by R24 and C12. During hori- Zontal syne time, diodes DS and D6 conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. \f the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). This is the correct polarity to cause the horizontal oscillator to speed up to correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D). Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor

PARABOLA FROM EMITTER OF O17 >

EXISTING VERTICAL SAWTOOTH WITHOUT BY VERT PARABOLA 1 ADDED

PARABOLA PULSE AND VERTICAL SAWTOOTH ADDED TOGETHER, HENCE PRODUCING THE REQUIRED VERT

DRIVING SIGNAL

+73V

Figure 4.

C13 times the phase detector for correct centering of the Picture on the raster.

HORIZONTAL OSCILLATOR

The horizontal oscillator employs the principles of the Hartiey type oscillator, Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off, The initial forward starting bias is supplied via R26,

HORIZONTAL PULSE SHAPER AND DRIVER

The horizontal pulse shaper Q7, serves as a buffer stage between the horizontal oscillator and driver. Capacitor C20, and resistor R30, combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.

The horizontal driver Q8, operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.

Resistor R35, and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36, is used for current limiting in the collector of Q8 , and C22 filters the horizontal frequency variations from the DC side of the transformer primary.

REFERENCE HORIZ. SYNC

OSC ON FREQ NO CORRECTION VOLTAGE DEVELOPED

OSC SLOWS, POS CORRECTION VOLTAGE

OSC FAST, NEG CORRECTION VOLTAGE

Page 31

= 12, wena WIDTH oll o2y cas on

1% ‘HOF RIV O82, (DO NOT MEASURE 08 —e- ars 5 fe -0.8V4 ent METER TO PIN ess tio HEATER 1D DAMPER | .01 VOLTAGE, oat fon Nt ore 2 aH ii ro PN. R39 an 330K t we Ik42 Focus 0 angen To 7 cRT “R34 (2nd ANODE +73V Wd ¥ TOCI ‘R? REO aw me Ee ib wt cAT ROMICAZ T Iso [aw Figure 5. sy

HORIZONTAL OUTPUT (See Figure 5.)

The secondary of T1 provides the required low drive impedance for Q9. Resistor R37, limits current in the base of Q9 , while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which, once each horizontal time period, connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27 since D8 will conduct if the collector voltage exceeds this value.

The damper diode D7, conducts during the period between retrace and turn on of Q9 to reduce retrace overshoot and capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from the deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor C32D is charged through D10 developing the video output supply voltage.

Tog. EMITTER

VERT. SYNC. INTEGRATOR gr ROA | RBA R50 .oay TocRT PINS

SYNC CIRCUITS (See Figure 6.)

The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negative going sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.

Resistors R45 and R46, provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, also providing base bias for Q12. Resistor R50, limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, teaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.

+1

Qi3

VERT. SYNC. AMPLy

10 C36 3.3K 13.3KjaW| ¢35 [c34 ARoar liad es

Page 32

+12V +73V

0,22 R66

c4a C41 fet TO ROB eri qis 82V ial VERT. OUTPUT L4B VERT. YOKE

Figure 7.

VERTICAL OSCILLATOR AND OUTPUT (See Figure 7.)

The vertical oscillator is a relaxation oscillator and operates at a free running frequency that is set by the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.

Diode 014 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14 and, D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.

The vertical choke L5, acts as a current source during linear scan time and provides a high voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.

Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical nonlinearity will result unless some compensation is employed.

Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of 37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40, couples the signal to the vertical yoke winding and blocks Dc.

SPOT KILL (See Figure 8.)

The spot kill circuitry is utilized to reduce the effect of the elctron beam concentrating on one area of the CRT after the monitor is turned off. This is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the high voltage charge which normally remains in the CRT.

When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 ‘on. When the monitor is turned off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of 20 from exceeding the reverse voltage rating of the transistor.

+73V

R73

TOR?7 CRT, PIN2 Figure 8.

Page 33

AUDIO MODULE (See Figure 9.)

The audio module has been designed as an optional add—on unit to the MS5010—155 and M7010—155 monitors. The module uses the +72 volt monitor power supply which is accessible through connectors P4 and P5, The audio input signal is applied to the 12—pin input connector, P1, located at the rear of the chassis. The audio amplifiers, Q1 and Q2, are connected in a negative feedback arrangement to improve bias stabilization,

Resistor R1 and capacitor C2 form a low pass filter which filters out high frequency logic pulses that may saturate Q1. Capacitors Ci and C3 block DC irom R2, eliminating the possibility of noise generation within R2 as its setting is varied. Capacitor C3 also prevents the bias of Q1 from being shifted as R2 is adjusted. Resistors R3, R5, RO and R10 form a negative feedback network which sustains bias Stabilization for Q1 and Q2. Resistor RO presents degeneration at the emitter of 2 for low signal distortion and C7 is a bypass capacitor which eliminates audio degeneration within the feedback network. Resistor R6 and capacitor C4 decouple the ripple from the +73 volt supply. Resistors R7 and R8 are a split collector load fur Q1, which provides base drive for Q2. Transformer T1 matches the impedance of the speaker to the output impedance >f Q2 while capacitors C5 and C6 are used for high frequency roll-off.

TO c31 AUDIO OUTPUT a2 MJE340K (HEAT SINK MOUNTED}

Figure 9.

BLANKING AMPLIFIER (See Figure 10.)

The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field.

Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses while R69 determines the amplitude of the horizonta! pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.

TO R74

c43 Ql6 A6J BLANKING AMPL.

Figure 10.

Page 34

a6 (CONTRAST) u (HORIZ. OSC.) 973 Raz aoe (BRIGHT) (FOcus) Lz FAEFC-00401

M5000—155, M7000—155, Chassis Rear View — Component Location

73 LS FI/F2 O15 RG (CONTRAST)

M5010—155, M7010—155, Chassis Rear View — Component Location

Page 35

MalA Japfog — /121aG p4seog INI 1OIIUO|

Page 36

C35 C36

637,38, 39 cao cat C42 ca ca cas cae

ca7 C48 C49

DIOOEs:

Di

D3 D4 05, 06 D7 os D10 23810255427 218135660 238187 A26 21S180E60 218138660 218131625

21S180B87

8S10191B99 $S10212B18 218131625 218180041 21S180C02 218180034 23S10228A32 8S10191B96 8510299B 28 8810299629 8S10191B98 218180851 8510191898 23S10255B50 218180851 8810299827 218131625 8810212411 8S10571A06 8S10212B53 8S10191B98 23810255873

8S10191A51 8S10191A32 21S180E60

8810191867 23510255460 8S10212B16 218180C82 8S10191B67 23510255B28 8810191890 218132492

23810255863 21S180D56 218180851

48S10813A03 48D67120A13 48S10813A01 48S191A02 48067120411 488134921 488134978 483191 A05 488137114 488137638 488191 A05 48D67120A11

488191 AOS: 48810813A02 48S10813A03 48D67120A11 485191 A05 MONITOR PARTS LIST

PART RE PART IN

CAPACITORS: (ALL VALUES ARE IN MICROFARADS

UNLESS OTHERWISE NOTED.

47, 50V; Lytic .05, +80--20, Z5V, SOV; Cer. Disc 22, 25V; Lytic .01, +80—20; Z5V, 50V; Cer. Disc 05, +80—20, Z5V, 50V; Cer. Disc 330pf, 10%, XBF, 500V; Cer. Disc 220 pf, 10%, X5F, S00V; Cer. Disc .015, 10%, 250V; Poly. 0.22, 10%, 400V; Mtiz. Poly. 330pf,10%, X5F 500V.Cer.Disc. .0027, 10%, Z5F, SOOV; Cer. Disc 10pf, 10%, N150, S00V; Cer. Disc 005, 20%, Z5F, 1KV; Cer. Disc 1.0, 16V; Lytic .033, 10%, 250V; Poly. .01, 10%, 100V; Polycarb, 0082, 10%, 106V; Polycarb. 01, 10%, 250V; Poly, £001, 10%, X5F, 500V; Cer. Disc .01, 10%, 250V; Poly. 150, 10V; Lytic 001, 10%, X5F, 500V; Cer. Disc 0.£2, 10%, 200V; Mtlz, Polycarb. 330pf,10%,X5F,500V; Cer. Disc. 1.0, 10%, 630V; Mtiz, Poly. .01, 5%, 1200V; Polyprop. Foil 0.47, 10%, 630V; Mtlz. Poly. 01, 10%, 250V ; Poly. 20/200, 400/125, 600/100, 200/50; Lytic 033, 10%, 160V; Poly. .047, 10%, 250V; Poly. .01, +80 —20, Z5V, 50V; Cer. Disc 0.22, 10%, 250V; Poly. 100, 63V; Lytic 0.1, 20%, 400V; Mtlz. Poly. 0.33,10%, N150,500V; Cer.Disc. 0.22, 10%, 250V; Poly. 4.7, 100V; Lytic .033, 10%, 250V; Poly. .01, +80-20, Z5V, 100V; Cer, Disc 100, 10V; Lytic 47pF,10%,N750,100V; Cer.Disc. 001, 10%, X5F, 500V; Cer. Dise

Diode, Silicon, Zener; IN5242 Diode; A13 Diode, Silicon, Zener; IN5234B Rectifier, Silicon; 91402 Diode; A11 Diode, Damper; D1D Diode, Pulse Lim; D1K

Rectifier, Silicon; 91405 Rectifier, Silicon; 91A05

Rectifier, H.V., D2¥ Vert. Osc.; MPU6027

Diode; A1t

Rectifier, Silicon; 91 AOS Diode, Silicon, Zener; 1N52318 Diode, Silicon, Zener; 1N5242 Diode; A11 Rectifier, Silicon; 91 A05 FUSES:

F1,F2 65S138269

INTEGRATEO CIRCUITS:

Ie 51810732A01

COILS/CHOKES:

24C25448A01 24025603 A0S 24D25248A14 24D25261A09

24D25261A10

25D25221C12

TRANSISTORS:

a1

a3 a4 as

a7 as ag

an a12 a3 a4 Q15 aie Qi7

arg 488137171 488137172 488137127 488134952 488137476 48S137172 485137127 488137093 488137570 488137173 489137172 488137172 488137172 485137632 485137596 488137172 488137368 48S134952 488137476 485137476

RESISTORS/CONTROLS: NCTE: ONLY POWER OR SPECIAL RESISTORS

ARE LISTED. USE THE DESCRIPTION

WHEN ORDERING STANDARD VALUES

OF FIXED RESISTORS UP TO 2 WATTS.

R6 R14 R17 R36 R42 R60 Re4 R66 R73 Rea ROS R95

SWITCHES:

swt 18D25245A27 178135204 17810731A01 17810130807 18D25218A14 18D25245A29 18D25245A31 6810201 A04 18D25245A28 178135589 18D25245A21 10731A03

40810624407

TRANSFORMERS:

T2

T3 25D25221A05 24D 25240823 25025239820

25D25239830 Fuse, 0.8A~-250V

Ref. Amp!.; T3F

Coil, Horiz. Osc. Coil, Horiz. Width Coil, Horiz. Lin. Coil, Defi. (M5000—155, 5010-155) Coil, Def. (M7000—155, 7010-155) Choke, Vertical

Emitter Follower; AGH Video Pre~Ampl.; AGJ Video Pre—Ampl.;P2S Video Driver; A2J Video Output; B1E Horiz. Osc.; AB Horiz. Pulse Shaper; P2S Horiz. Driver; ASF Horiz. Output; B2L Sync Separator; P2W Syne Ampl.; A6S Vert. Sync Integrator; A6J Vert. Sync Ampl.; AGJ Vert. Driver; MPS A13 Vert. Output; B2V Blanking Ampi.; A6J Regulator; ASW Reg. Driver: A2J Reg. Buffer; B1E Spot Kill; B1E

Control, Contrast; 500 100, 10%, 5W 3.9K, 5%, 5W 1.5K, 10%, 3W Control, Focus; 2M Vert. Size; 250K Vert. Lin.; 100K Varistor, 1 ma, 120V, 0.5W Control, Brightness; 200K 150, 10%, 10W Control, +73V out Adj.; 2.5K. 1.5K, 10%, SW

Switch, Slide; D.P, 0.T.

Horiz. Driver HV. Transformer Transformer, Power (M5010 —155, M7010--155) Transformer, Power (M5000 —185, M7000-155)

Page 37

Mt 96S241A01

M1 96S10848A01

MECHANICAL PARTS:

9825456A01 42D25158C01 26810251 A08 Pa 15510183069

39810184467

P2 15$10183A82

P2 15S10183A81

39810184467 P3 28S10586A35 P4,P5 15$10183812

39S10184A84 MONITOR PARTS LIST (Con’t.)

19” — CRT; Type 19VARP4 (ms000/M5010) 23” — CRT; Type M22VATP4 (M7000/M7010)

Block, Fuse (F 1,2) Clamp, Defl, Coil Heat Sink (05) Housing, Connector; Female (12— Contact, Less Contacts) Contact, Plug; 5—Rea’d M5000/ M7000, 9—Req'd; M5010/M7010. Housing, Connector; Male (3— Contact, Less Contacts), M5000/ M7000 Housing, Connector; Female (3— Contact, Less Contacts), M5010/ 7010 Contact, Plug; 3-Req’d for P2 Header, Connector; 2—Contact Housing, Connector; Female (3— Contact, Less Contacts) M5010/ M7010

Contact, Plug; 3 ea. Req'd for

P5, M5010/M7010

REPLACEMENT PARTS LIST FOR +5 VOLT SUPPLY (M5010/M7010)

CAPACITORS:

C201 C202

DIODES:

D201 D202 23510255830 21S8180B51 23810255882

48S137670 48510641043

FUSES:

F201 65$139733

INTEGRATED CIRCUITS:

§1S1073201 1C201

TRANSISTORS:

485137634 485137169

RESISTORS/CONTROLS: R206 18D25245A04 MECHANICAL PARTS: 7B25466A01 42S810122A12 140562353 14S10550A02

2810080A26 38139702

38136050

9C63825A03 PART DI 1 x. NUMBER ncminchdmcld

Transistor, Regulator: 7634

Transistor, Regulator Driver: 5000, 20V; Lytic .001, 10%, X5F; Cer. Disc 100, 10V; Lytic

Rectifier, Diode Module; 7670 Diode, Zener; 4.3V

Fuse, 7A—125V

Reference Amplifier; T3F

ABG

Control, +5V ADJ.; 4K

Bracket, Heat Sink (Q201) Fuse,Clip; 2-Req‘d. for F201 Insulator, Mica (201) Insulator, Transistor Cover (0201) Nut, 6—32 x 5/16 (Mtg. 0201) Screw, Mch.; 6-32 x 5/8 (Mig. D201) Screw, Tpg.;6—20 x % Clu Pan (Q201) Socket, Power Transistor (Q201) 15S10183A81

s2 15$10183A82

39810184064

S3 15$10183A94

39810184472

14825459401 144562353 14C25230A01

1410157430

14S10580A02

33136050

9D25470A01

90D25201A01 9C63825A03

41D65987A01 PART PART RIPTION No. | NUMBER Descent ion Li | NUMBER ESE) a MISC. ELECTRICAL PARTS: Housing, Connector; Female {3-Contact, Less Contacts), M5000/M7000 Housing, Connector; Male (3-Contact, Less Contacts), ™M5010/M7010 Contact, Receptacle; 3-Rea‘d. for SZ Housing, Connector; Female {2-Contact, less Contacts) Contact, Receptacle; 3-Req'd. for $3 Insulator, Fuse Cover (F1,2) Insulator, Mica (09,015,017) Insulator, Molded (On D11 Body) Insulator, Nylon (2-Req'd); Mtg. P.C. Board Insulator, Transistor Cover (Q9,015,017) Screw, Tpg; 6-20x% CLU Pan (Mtg. Q9,Q15,Q17 and B11 Socket) Socket, CRT; R79, R80 Socket, H.V.and CRT Anode Socket, Power Transistor 9,015,017) Spring Special; CRT Aquadag Gnd, Incl’s.277,R78,

PARTS LIST FOR KV800A AUDIO MODULE (M5010/M7010)

CAPACITORS:

23S187A16 21S180F45 238187A16 23810255828 218180890 218180803 23S187A16

TRANSISTORS:

Qi 488137171 a2 485137648

RESISTORS/CONTROLS:

R2 18D25245A30

TRANSFORMERS:

1 25D25221A11

MECHANICAL PARTS: 42B25460A01 26025198A02 26C25198A04 15S10183B09

39S10184A83

14025461401

2S810080A26 38138058

50D25453A01 PART TION

100, 16V; Lytic .015, 20%, 100V, Z5U:; Cer. Disc 100, 16V; Lytic 4.7, \00V; Lytic .01,20%, 100V, Z5U; Cer.| .02,20%,Z5U, 500' ‘er. Disc. 100,16V; Lytic

Audio Driver; A6H Audio Output; 7648

Control, Volume; 10K

Audio Output

Clamp (Mtg.Ckt. Bd, to Spkr.) Heat Sink (Q2) Heat Sink (Q2) Housing, Connector; Female (3-Contact) Contact, Receptacle; 3-Req'd. for §1 Insulator, Washer; PC Board to Spkr. (LS1) Nut, 6-32 x 5/16 (Mtg.Q2) Screw, Mch., 6-32 x 3/8 (Mtg. 02) Speaker, P.M.; 4" x 4”

Page 38

POWER SUPPLY

To 45.0¥ rea 350 @ rout 27V +130 i suPly ercut co LO care

s.r oy eh ee

oaTwoue) es 10 va weaves VOLTAGE} FOR V1

M5010—155, M7010—155 — Diagram Schematic

Page 39

To MAIN BOARD +73V (GND)

+73 IN

OVERLAY —BEPC.00417

SOLDER SIDE ~ BEPC-00418 OVERLAY — BEPC-00419

Audio Module Circuit Card Detail — Solder View ToLs1

TOLSt

#31 MATES WITH P4j25 ON MONITOR CHASSIS. To.a201 COLLECTOR

Page 40

AG INPUT FROM SEC. OF PWR XFMR TS

+73V FROM MONITOR cwmcurt i CARI ac aang REGULATED g208 7634 (wear sine MOUNTED) @+ TO PING OF P4 REGULATED +5,0V AT 308 OUTPUT >—— TO PIN 3 OF PA

AC F201

+73V { GND =< Cant

AUDIO OUTPUT T

us4 Bn

AUDIO OUTPUT Qi MJE340K (HEAT SINK MOUNTED)

Audio Module — Diagram Schematic

Page 41

M1 (DIQDE MODULE)

'C1 p202z

R206 +5V ADJ.

0201

FAEPC~00404

Audio Module — Circuit Card Detail - Component Location