The Real Ghostbusters Conversion Kit 2 Player (780-0070-01)
The Real Ghostbusters (US 2 Players, revision 2) (Data East USA, 1987) · Manual · 12 pages · 3 sections · original scan
THE REAL
GH@STBUSTERS
2 PLAYER CONVERSION KIT
MODEL NUMBER 1US30K
INSTALLATION & SERVICE MANUAL
D fa DATA EAST USA, INC. 470 NEEDLES DRIVE KI SAN JOSE, CA 95112 TELEPHONE: (408) 286-7074
MANUAL PART NUMBER: 780-0070-CH
not installed and used properly, ie., in strict accordance with is instructions manual, interference to radio communications. This equipment has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of the FCC regulations, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environgent.
Operation of this equipment in a residential environment is likely to cause interference which the user, at his own expense, FCC WARNING
This equipment generates and uses radio frequency energy and if
may cause hareful
will be required to take whatever measures are necessary to correct the interference.
ENVIRONMENTAL DATA
This product is intended for indoor use only, power requirements are 105-125 volts AC 50-60 hz, and requires a 3 wire grounded outlet.
FBI WARNING
Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games. The Federal Bureau of Investigation investigates allegations of criminal copyright infringement. —I
COPYRIGHT NOTICE
The Real Ghostbusters is Copyright 1984 Columbia Pictures Industries, Inc. Copyright 1986 Columbia Pictures Television, a division of CPT Holdings, Inc. All rights reserved.
The Real Ghostbusters video game 1s Copyright 1987 by Data East USA, Inc. All rights reserved, licensed from Columbia Pictures Industries, Inc.
REPLACEMENT PARTS AND SERVICE
To obtain replacement parts or technical assistance, contact the authorized Data East distributor in your area. If you require teferral or further technical assistance, you may contact Data East's Customer Service department during the hours of 8:00 am to 5:00 pm Pacific Time at (408) 286-7074. Diwiinierseterste sisted ar senengetienatetinienitaieseanitinsieemnsinciy
GHOSTBUSTERS 2P
MODEL NUMBER 1US30
INSTALLATION & SERVICE MANUAL
TABLE OF CONTENTS
. Game Options
PCB Edge Connector Pin-Out...eseseceecereeeereeceee seal
. Main Harness Edge Connector Pin-out...... Seam eeenenees 8 GENERAL INFORMATION
Specific Requiremerits.....ssssseevecceevos ee eeccereseed
« List of Materials. .cccc cece cece cree net en nese cer eecnces 1
Installation Instructions....csseeeeeeececeecceeveeenes 2
GAME INFORMATION
© 1986 DATA EAST USA, INC. 470 NEEDLES DRIVE SAN JOSE, CA. 95112 (408) 286-7074
FIRST PRINTING FEBRUARY 1988
PN: 780-0070-O1
Ir 71 H 1. GENERAL INFORMATION |] i}
| A. Specific Requirements. |
The Ghostbusters 2P game is a One or Two Player video game conversion kit. It is intended to be installed into an existing video game cabinet and comes with all the necessary components to make the converted game look and play like a new dedicated game!
THE GAME TO BE CONVERTED MUST MEET THE FOLLOWING REQUIREMENTS
anon | 1 MONITOR Horizontal, RGB, negative Composite Sync input.
POWER SUPPLY + & vde @ 7 amperes, and + 12 vde @ 1 ampere (min)
B. List of Materials.
DESCRIPTION PART NUMBER
| 1 | PCB, GHOSTBUSTERS 2P | 510-0110-01 |
| 1 | PCB, EMI FILTER, DE-0239 | §20-0083-00 |
| 1 | MAIN HARNESS, GENERIC KIT | 036-0154-00 |
| 2 | JOYSTICK, 8 WAY, MICROSW., CC | 450-0014-01 |
| 2 | PUSHBUTTON ASSY, RED | 350-0016-02 |
| 4 | PUSHBUTTON ASSY, YELLOW | 350-0016-04 |
| 4 | PUSHBUTTON ASSY, BLUE | 350-0016-06 |
| 1 | CONTROL PANEL OVERLAY, GENERIC | 800-0030-00 |
| 1 | UNDERLAY CARD, GENERIC, H-V | 810-0014-00 |
| 2 | LABEL, BUTTON ID, GENERIC | 406-0085-00 |
| 1 | LABEL, INSTRUCTIONS, GHOSTBUSTERS | 406-0078-00 |
| 2 | SIDE DECAL, GENERIC | 820-0040-00 |
| 1 | MARQUEE PLEX, GHOSTBUSTERS | 830-0033-00 |
| 1 | FCC WARNING LABEL | 406-0003-00 |
| 1 | MANUAL, INSTALLATION & SERVICE | 780-0070-01 |
PAGE 1 INSTALLATION & SERVICE MANUAL
Installation Instructions.
When selecting a game to convert, make sure that the Power Supply, the Monitor, and the Coin Acceptors are functional. There is nothing more frustrating than installing a conversion kit and having it not operate due to a faulty Monitor or Power Supply. I know...we will all suspect that the new Logic PCB is defective, right?
It is mandatory that the cabinet be wired to conform with all National and Local Electric Code requirements before the conversion is attempted, The primary section must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference. ‘Adequate’ is defined as a filter with both common mode and differential mode filtering and a minimum current capacity of 1 % amperes.
According to the FCC and other regulatory agencies, every video game must have be clearly labeled with the Name and Address of the Original Manufacturer, Date of Manufacture (or serial number), Voltage Rating, Current Rating, Suitability for indoor or outdoor use, and Model Number. In addition, the FCC requires that after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a _ residential area. An acceptable sticker is included in this kit.
IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE INSTALLATION TO COMPLY WITH ALL LABELING REQUIREMENTS.
TAKING IT APART...
Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit.
Find the wiring diagram of the game to be converted! You will need to identify the required DC power supply output wires and the monitor video .and syne wires. Note the color coding of these wires or better yet, label them as to their function. This kit contains a new Main Harness, but you will need to splice it into the existing power supply and vider wires.
Remove the existing game harness parts that will not be used in this conversion. NOTE: You are modifying only the secondary (DC from power supply) and 1/0 (video, speaker, and controls) section of the wiring. DO NOT MODIFY OR REMOVE THE PRIMARY AC WIRING. The primary AC wiring has been designed and built to comply with UL and FCC regulations and must not be altered.
INSTALLATION & SERVICE MANUAL PAGE 2
Cc. Installation Instructions (cont.)
Remove the game pebs. Remove all exterior decals and repaint the cabinet if necessary. Repair any cabinet damage at this point. Remove the monitor plex (or glass). If your plex has silkscreened artwork on it, you will need to strip it off, or replace the plex with a piece cut to the same size. Using the Monitor Plex as a template, cut the supplied Underlay Card to the same size as the plex. NOTE: Be certain that the opening in the Underlay Card lines up with the Monitor CRT.
Remove the Marquee Plex from the game and use it as a template to cut the new Marquee Plex down to the correct size. Remove the control panel from the game and remove all controls and graphics from it.
PUTTING IT TOGETHER...
Control Panel: This is never any fun, so lets do it first and get it out of the way. Select a button and joystick layout that fits your control panel size. Refer to figure 1 for the suggested panel layout.
START START
Figure 1
PAGE 3 INSTALLATION & SERVICE MANUAL
Installation Instructions (cont.)
Install the Control Panel Overlay by peeling off the paper backing and carefully laying the overlay down onto the panel. Smooth it out starting in the center and working your way out to the edges, removing all of the trapped air pockets. If possible, cut the edges of the overlay oversize and fold the excess under the panel. Cut out the button and joystick holes. Install the Control Function Labels found on the sheet of labels supplied in your kit. NOTE: Install the Control Function Labels in the formation shown in figure 1.
Cover the Control Panel Overlay and Control! Function Labels with a clear plex to protect the overlay and labels. Install the buttons and joystick at this time. Mount the completed control panel to the cabinet.
Game PCB: Mount the game PCB set to a convenient wall of the cabinet using the mounting feet and hardware supplied with the pcb. Plug the EMI Filter PCB onto the game PCB set.
Power Supply Wiring: Plug the Main Harness edge connector onto the EMI Filter PCB’s edge connector. Separate the DC Power wires and route them through the cabinet to the Power Supply. Try to keep the length of these wires to a minimum for best results. NOTE: Use a minimum of 2 wires EACH for the +5 Volts and the Ground lines between the power supply and the PCB, Terminate them at the Power Supply as required.
[ wore: IMPROPER WIRING WILL DAMAGE THE PCB SET AND VOID YOUR waranty: |
Player Control Wiring: Route the Pushbutton and Joystick wires up to their proper destinations, cut to length, and terminate as required.
REFER TO THE EDGE CONNECTOR PIN-OUT ON PAGE 8 FOR WIRE COLOR AND FUNCTION INFORMATION.
INSTALLATION & SERVICE MANUAL PAGE 4
i C. Installation Instructions (cont.) | L i
Monitor Wiring: The game PCB set has outputs for Positive Red, Green, Blue, and Negative Composite Sync. If your monitor has separate Horizontal and Vertical syne inputs, hook the Composite sync to the negative Horizontal input. This method will work on most monitors, however some model Electrohome’s require that the Composite sync signal be hooked up to both the negative Horizontal and Vertical inputs. Contact your distributor for more information if you are uncertain as to how to hook up the monitor wires.
Coin Door: The Coin Counter(s) may be the 12 volt or 6 volt type as the game PCB utilizes an open collector drive circuit. Hook one coin counter wire to the required voltage (+12v or +5v) and the other wire to the coin counter signal wire from the game PCB.
Graphics: Install the Game Instruction Labels onto the Underlay Card, either in the lower portion, or on one side of the picture tube cutout. Install the Underlay Card under a clear monitor plex (or glass). Mount the new Marquee Plex, and install the Side Decals. NOTE: Install the FCC Warning label to the upper rear of the cabinet.
THE BIG TEST!
REMOVE THE MAIN HARNESS EDGE CONNECTOR FROM THE GAME PCB!
Apply power to the game. Measure the +5 volts at the edge connector and adjust to +5,15 VDC using a Digital Multi-Meter. Measure the +12 and -5 vde wire to be certain they are connected preperly and are on the correct terminals. Remove power to the game.
RE-CONNECT THE MAIN HARNESS EDGE CONNECTOR!
Apply power to the game once again. The attract mode video should appear on the screen. Adjust the picture size and colors on the monitor to get the optimum appearance. Adjust the Sync and Hold controls on the monitor for a stable picture. Coin it up and give it a try! Test all the controls and sound for proper operation.
Congratulations! You have successfully installed your Data East conversion kit! We hope that it gives you many years of successful operation.
PAGE 5 INSTALLATION & SERVICE MANUAL
al { 2. GAME INFORMATION || t |
Game Options.
The Ghostbusters 2P game options can be fine tuned to suit the location via two sets of dip-switches on the Game PCB. Remove power to the game before changing the settings to avoid possible shock hazards. switches indicated should be left in the OFF position as shown for proper operation. Factory settings are boldface,
DIP SWITCH 1
| REMARKS | 4 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| COIN | 1 COIN = 1 PLAY | OFF OFF | ||||||
| vs | 4 COIN = 2 PLAY | ON OFF | ||||||
| CREDIT | 1 COIN 3 PLAY | OFF ON |
2 COIN = 1 PLAY ON ON
| NOT USED MUST BE OFF | OFF OFF OFF | OFF! |
| ATTRACT MODE | YES | OFF |
| SOUND | NO | ON |
| SCREEN | NORMAL | OFF |
| FLIP. | FLIP. | ON |
DIP SWITCH 2
| REMARKS. | al | 2 | 3 | 4 | S | 6 | 7 | 8 |
| NUMBER OF | THREE | OFF OFF | ||||||
| LIVES | FIVE | ON OFF |
ONE OFF ON
| — | INFINITE | ON ON |
| LEVEL OF | NORMAL | OFF OFF |
| DIFFICULTY | EASY | ON OFF |
HARD OFF ON HARDEST. SCENE 5:00 TIME (MAX) 6:00 IN 4:30 {__ MINUTES 4:00 CONTINUE NO MODE YES BEAM ENERGY NORMAL, PICK-UP UP 1.5%
INSTALLATION & SERVICE MANUAL PAGE 6 Unused
B. PCB Edge Connector Pin-Out. | j
The game PCB set uses a 56 pin ‘JAMMA’ standard Edge Connector pin-out as shown below in figure 2. Please note that the Main Harness supplied in the kit utilizes the pin-out following page.
SOLDER SIDE and wire colors shown in figure 3 on the
PARTS SIDE GND GND GND GND +5V +5V +5V +5V
+12V +12V
MISTAKEN INPUT PREVENTION MISTAKEN INPUT PREVENTION
COIN COUNTER 2 COIN COUNTER 1
SPEAKER (-) SPEAKER (+)
VIDEO GREEN VIDEO RED VIDEO SYNC VIDEO BLUE SERVICE SWITCH VIDEO GND
COIN SWITCH 2 COIN SWITCH 1 START SWITCH 2 START SWITCH 1 A 2P_CONTROL UP 1P CONTROL 1 _uP 2P CONTROL 2 DOWN 1P CONTROL 2 DOWN 2P CONTROL LEFT 1P CONTROL 3 LEFT 2P CONTROL RIGHT 1p CONTROL 2P CONTROL PUSH 1 1p CONTROL 2P_ CONTROL PUSH 2 IP CONTROL 6 PUSH 2 _
PAGE 7 INSTALLATION & SERVICE MANUAL
C. Main Harness Edge Connector Pin-Out.
The DE-0239 EMI Filter PCB uses a 44 p pin-out as shown below in figure 3.
SOLDER SIDE
WIRE COLOR FUNCTION |PIN #
OR/WH 2P LEFT = RD/WH apricit | as | PK/WH NOT USED 2P PUSH3 _ BS NoT USED |
i NOT USED
NOT USED
2P PUSH1 (FIRE) ag
2P PUSH2 (BEAM) ALO PIN #| FUNCTION in DECO standard Edge Connector
COMPONENT SIDE
WIRE COLOR}
1P DOWN
1P RIGHT
1P PUSH3 NOT USED PI
NOT USED
NOT USED
NOT USED
1P PUSH1 (FIRE)
1P PUSH2 (BEAM)
COUNTER 1 COUNTER 2 | Al
VIDEO GREEN
VIDEO RED VIDEO BLUE
VIDEO SYNC
NOT USED NOT USED
SPEAKER (-) SPEAKER (+)
- 5 VOLTS
+5 VOLTS | aig + 12 VOLTS
+ § VOLTS
A20 +5 VOLTS + § VOLTS
GROUND GROUND
Figure 3
INSTALLATION & SERVICE MANUAL PAGE 8
WARRANTY INFORMATION
Data East USA, Inc., (“Seller”), warrants only to the original purchaser (“Buyer”), of its products that the items listed below are free from defects in material and workmanship under normal use and service for the period specified:
GAME LOGIC PRINTED CIRCUIT BOARD(S) 90 DAYS
No other parts of the Seller's products are warranted.
Warranty periods are effective from date of initial shipment from Seller to Buyer. Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
- Seller is notified promptly upon discovery by buyer that stated products are defective.
2, Such products are properly packaged and then returned freight pre-paid, to a place specified by Seller.
This warranty does not apply to products damaged during shipment and/or due to improper handling, or due to improper installation or usage, or alteration. Inno event shall Seller be liabie for any anticipated profits, loss of profits, loss of use, accidental or consequential damages, or any other losses incurred by the customer in connection with the purchase of a Data East USA, Inc., product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND BUYER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.