CATHODE RAY TOMES

Pit and Run Universal Kit

Pit & Run (Taito America Corporation, 1984) · Kit Manual · 23 pages · 6 sections · original scan

Page 1

TAITO AMERICA CORPORATION

CONVERSION KIT

Page 2

TABLE OF CONTENTS

CONVERSION INSTRUCTIONS .e eee cece ccc cee cee cece eect eee edad

REPLACEMENT PARTS LIST .ecceeecc ccc ce cece cece cece seer ee ee 596

LIST OF FIGURES

GROUND PLATE ASSEMBLY 1... cece ce cec ccc ec ccc cce ec esccseee 7

WIRING DIAGRAM .c cece cece cece cece cece eee e cece esse ceccees &

JOYSTICK TEMPLATE 2... cece ec ee cece cere cee ee eee recseees 9

SCHEMATICS ce cesses ccc e cece cece cece eee e eee eeteeeeseces 10-22

Page 3

This manual will guide you in the conversion of your raster scan, color monitor upright video game into a PIT & RUN game. We urge you to read through the instructions and study the drawings before beginning the conversion. Perform the instruction steps in the order presented.

  • Check the parts supplied in this kit against the parts list in the manual.
  • Cabinet preparation,

a. Remove the exsisting logic boards from cabinet.

b. PIT & RUN requires a vertically mounted monitor. Remount monitor in

the best possible way viet =. horizontally mounted. Note: PIT &

RUN generates composite negative sync.

c. To insure compliance with FCC regulations, the power supply used for PIT & RUN must meet these requirements:

A line filter must be installed between the power supply and the AC line. Taito recommends a Corcom model #681 or equivelent. Taito part no, #22-00001-001

A single point ground must be maintained thoughout the game, i.e, the chassis for the power supply. the monitor chassis and the ground plate for the PCB set must be connected to the green "earth ground" wire in the Ac line cord.

The power supply must meet or exceed the voltage and current requirements,

+5 volts @ 4 amps +12 volts @ 1 amp

d. PIT & RUN requires a speaker with a nominal impedance of 4 ohms or greater.

  • Install Ground Plate, filter board and PCB.

a. Locate the the Ground Plate on a cabinet wall. Experiment to determine the best orientation for the plate remembering that the game PCB set must be able to slide into the card guides. Mount the plate to the cabinet using a 8x11/16 screw in each corner. Using the holes in the plate as a template, screw the two PCB mounting brackets into the cabinet using the 8 x11/16" screws provided. Be carefull not to bow or bend the ground plate. It must lay flat against the mounting surface.SEE FIGURE 1.

b. Depending on the installation. the PCB set may have to be slid into place before the filter board is mounted. If this is the case, slide the PCB set into place before mounting the filter board.

Page 4

Cc. Using the holes in the plate as a template, screw the filter board into the cabinet using the 6 x 1 1/2" screws provided. SEE FIG. 1.

Slide the PCB set into the guides with the edge connector facing the filter board and the component sides of the PCB set facing outward. Push the PCB set edge connector GENTLY into the connector On the filter board. Be sure the connectors on the PCB and filter board are aligned properly.SEE FIGURE l.

Mount the "L" bracket into the cabinet, using a 6 x 1/2" screw provided, on the left side of the PCB to keep it from sliding. SEE FIGURE 1.

  • Connect the main harness.

a.

Db. Connect the 44 pin edge connector of the main harness to the filter board, observing the keying plug. SEE FIGURE 1.

Connect the 12 pin connector of the main harness to the filter board. Connnect the "power jumper" cable between the filter board and the PCB set.

Using the supplied wiring diagram as a guide, connect the main harness ends to the correct power supply, coin door and speaker connections. Note: The coin door bundle of wires contains an orange wire to be connected to a tilt switch. To enable the tilt “feature, cut the J5 jumper on the center board of the Pit & Run PCB set. Connect a NORMALLY CLOSED switch between ground and the orange wire. If the tilt feature is not desired, then DO NOT cut the J5 jumper and tie the orange wire out of the way.

Connect the gray video cable to the monitor. The connectors will mate with most Wells Gardner and Electrohome monitors. If using a different monitor, use the wiring diagram as a guide in wiring the video cable to the monitor.

  • Rework control panel.

a.

b. Strip the control panel of all buttons and/or joysticks.

Locate and drill the holes needed for the joystick and buttons. Use template supplied with kits to locate holes for the joystick. Clean any burrs from around holes.

Remove any soil and/or grime from the front of the panel.

Cut the lexan to the approximate size needed to cover the panel. If possible, leave enough lexan to wrap a small lip around the top and bottom of the panel.

Page 5

e.

h. Peel the backing off the lexan and apply it to the control panel. Cut out the lexan from the holes needed for the joystick and buttons.

Install joystick, buttons and any hardware that might have been removed on the panel.

Using the supplied wiring diagram as a guide, connect the joystick and buttons to the main harness. Note: A section of black wire is supplied with the kit for jumpering grounds between the push buttons and joystick switches.

Mount the control panel back on the cabinet.

  • Install marquee overlay.

d. Remove marquee and clean soil and grime off.

Cut the marquee overlay to approximately the size needed.

Peel the backing off the overlay and apply the overlay to the marquee. Trim excess overlay off with a sharp knife or razor blade.

Replace the marquee back on the cabinet.

  • Install Ground Braids.

a. Connect one end of a 28 inch ground braid to the Ground Plate at a convenient corner with a screw. Connect the other end of the ground braid to a convenient point on the the power supply chassis ground.

“Connect another 28 inch ground braid from a convenient point on the power supply ground chassis to a convenient point on the monitor chassis.

  • Game Adjustments

a. Consult the PIT & RUN Switch setting card and adjust the DIP switches as desired. Attach this card to the rear door of the game for future reference.

Turn the game ON and play a "2-PLAYER" test game. Adjust the volume controls as desired.

Some adjustments may have to be made to the horizontal and vertical frequency controls on the monitor. Some centering and width adjustments may also have to be made.

  • Attach FCC compliance and FBI warning labels.

Affix the FCC compliance and FBI warning labels to the back of the cabinet.

Page 6
  • Attach the Instruction card.

Affix the instruction card to a convenient location on the coverglass.

The conversion is complete.

Page 7

PIT & RUN CONVERSION PARTS LIST

CONVERSION KIT

DESCRIPTIONQUANTITYPART NUMBER
PCB set108-00146-001
Filter Board108-00147-001
Ground plate161-00361-001
Marquee overlay, PNR166-00018-001
Control panel overlay166-00005-001
Main Harness109-00317-001

MANUAL PACK

DESCRIPTIONQUANTITYPART NUMBER

Switch Setting Card 79-00105-001

Instruction card179-50040-001
Conversion manual172-10025-001
FCC Compliance Label179-00070-001
FBI Warning label179-00074-001
Page 8

CONTROL PANEL PACK

DESCRIPTIONQUANTITYPART NUMBER

“Accelerate” button ——=«22~S~S*S*S*S«S SOSH =DOE

1 player button163-00176-001
2 player button163-00176-002
P.B. Switch429-00020-001
Stamped nut454-07001-008
Ball and Shaft163-00031-002
Mask163-00033-001
E ring159-00020-017
4 way leaf switch163-0003 2-004
4 way actuator163-00030-002
#10x24 carriage bolt451-03004-013
#10x24 keps nut454-02004-001

PARTS PACK

DESCRIPTIONQUANTITYPART NUMBER
PCB mtg. bracket207-00364-001
Power jumper cable109-00318-001
Screw #8x11/161051-00005-001
Screw #6xl 1/2"451-01012-015
"L" bracket161-00014-001
Screw #6x1/2"151-01012-006
Black wire5'28-00009-000
Tye wraps1059-00003-001
Page 9

FIGURE 1

PIT & RUN KIT - PCB & FILTER BOARD

° ie) ©) °

rT o o

i = | = = = = =a = = = =| = =n

  • i} POWER JUMPER S| CABLE S| =n =

;

e| J

ff) ay yy] ol - = ol} a HM / ie) ° ie) FILTER ‘BOARD oO, / 7 ee

PIT & RUN PCB GUIDE ASSY. FIGURE | "GR STRAP PCB SET GROUND PLATE ASSY. DETAIL 28 GROUND. TO POWER SUPPLY CHASSIS

Page 10

J

PIT & RUN PCB

POWER JUMPER

FILTER PCB FIGURE 2 PIT 8 RUN WIRING DIAGRAM

—j——_ BLACK A} Gaay —— GROUND iS ORANGE Hai 14 SeLLOW Ren

15 PELL OYRIGHTCONTROL PANEL BUNDLE

& i LEFT

OLET ACCELERATE

NP BLUE 2 PLAYER

a Bac GROUND GRAY. COIN SWITCH Cc

ea naroe sours’~COIN DOOR BUNDLE
i=LLOSERVICE SW.

CH LORANGE TILT

[s] @ pRED VIDEO RED (MI-6) So} GREEN me 1 VIDEO GREEN © (MI-8) VIDEO BLUE (MI-4) VIDEO CABLE (SEE Note) F< \— COMPOSITE SYNC (M2-1,M2~- B_LSHIE! "SHIELD (mMt- 3) , ORANGE Sfatack aublo . SPEAKER BUNDLE foo} up OPTIONAL 2 PLAYER a CONTROLS FOR COCKTAIL aoe TABLE INSTALLATIONS ACCELERATE

T7-LBLACK + BLACK 8 volts

RED+svolTsPOWER SUPPLY BUNDLE

9 +12 VOLTS

NOTE: MI AND M2 CONNECTORS MATE WITH WELLS~GARONER, ELECTROHOME AND EQUIVALENT MONITORS. Si ADDITIONAL NOTE! | On some kits, the coin sw: the instead of BROWN as shown

diagram. itch wire is RED wiring

ply for +5 and ing the power SUPP" ue PCB SET. d just: When adj ae voltages +12 volts,

Page 11

SOUND BOARD LAYOUT

O°

fetta ca-| Eee =

ww 6 wason [LPR 26 ¢G Roars) D> 38 404 [1 4- 8 cS 33 @ ae) SE) gas D | SOUND IC 17 SiCio | fiCIO AY-3-8910° J i" g [ SOUND. iGa7 F AY-3-8910

=B &

ra 41 }+ CID [er oO w

& : eet five .

Rp ce

Fics]. Bic is] a ele J AGT Nkis\e'e)

Page 12

TT IS

5 sc yap2—s Mis) zac so2payt

740a 7404 4 res 21 2B | Laie 2B VSYNe aoe 74.574 |e Fat Rot tlex a i

on 2@/T auvod dNnos

Page 13

on é T 2, 47K t 47K Ez 10p

° GND:

1000p 2204 1S158 a

40K: —, 190K gr 3200 , : ELECTROLYTIC - BLOCK 5 [ae : : ! CERAMIC Veo ACK 270K -

ai soosro| @/e duvod annos

Page 14

CPU BOARD LAYOUT

Page 15

P 8 ul Zen eI [L j Pee EER 2-8. Ceae) G@=32)

amr) j 74832 Licht —_HSK

  • Fees = (AT) 8 7 [ $ 4 3 M1) oO

ws

a n/T auvod nado

Page 16

af LXED MN ai)

A= NMICN (ET) n/e qavod ndo

Page 17

“n

m

Ww H FIL? (4-51)

cs ~ a n/E duvod ndo

Page 18

Last lll {ok as

rs h/h Guvod ndo

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

6r nae 6S soc = SEEN 1 CBE KAE)(2 CRUE Ce2xA6: (3-82) p x I HAP i (4-04; —— Hl EE i i wee) . -- 1 9e Geel —_____ale FLIED a3)

  • TALSR6

lay oc 22

(ey Bick ii TASC ay ASK

6)

uy Tg ae wT (2-84)

a

m

co)

iw

~~ H/T GuVOd OIA

Page 21

ey

CIA)

(1-84)

off

‘4 4 | RES a pris z

Vf Gly ETE ob ma n

= fe HFIP x (3° 88) 0B 86% CFI)

H2— 8B (3-B3)(3-93) ca

w 27S) : ‘1 ah eR al | Q-€3] [Be og TAGES cy lw

iY mass? | woo be 39 +

© h/e Guvod OFdIA

Page 22

TNT BU

ja

WELS00 TSA

o m

~oa 7

oO

mM

TT /E GUYOd OACIA

Page 23

or ce ECaELIE Kester]

@ oC sala ! 2 78 Mm rok ral 741508 7ALS32, h/h GUVOd OACIA