CATHODE RAY TOMES

Arabian SP-237 1st Printing Troubleshooting Guide

Arabian (Sun Electronics, 1983) · Troubleshooting · 9 pages · 40 sections · original scan

Page 1

Arabian™ Troubleshooting Guide

*Manufactured under license from Sun Electronics Corporation

AL

ATARI

©ATARI INC., 1983

SP-237 1st printing

Page 2

Troubleshooting Guide Arabian

TABLE OF CONTENTS

Troubleshooting with the Atari CAT Box and Z80 Interface Adapter

Preliminary CAT Box Set-Up ..

‘Troubleshooting with the Read/Write Controller Working RAM (IC10) Check Display RAM IC154-185) Check

‘Troubleshooting with Checksums 2 Program ROM (IC1-4) Check 2

‘Troubleshooting with Signature Analysis... .....--.- 066000 e eee eee 2

Signal Name Descriptions for Arabian

Page 3

Arabian ‘Troubleshooting Guide

Troubleshooting with the

Atari CAT Box and Z80 Interface Adapter

Preliminary CAT Box Set-Up

2.

3.

10.

Troubleshooting with the Read/Write Disconnect the electrical power from the game. Disconnect the wiring harness from the game PCB. Remove the game PCB from the game cabinet. Remove the Z80 Microprocessor 1C15 from the game PCB. Connect the CAT Box flat cable connector to the 50-pin connector of the CAT Box/Z80 Interface Adapter. Connect one end of the 40-pin flat cable supplied with the Interface Adapter to the 40-pin connector of the Interface Adapter. Connect the other end of the 40-pin flat cable to the socket of Z80 microprocessor IC15 on the game PCB. Connect the DATA PROBE ground of the CAT Box to the ground bus bar adjacent to Game Microprocessor IC15 on the game PCB. Apply power to both the CAT Box and the game. Set the following CAT Box switches as indicated: R/W MODE: (OFF) R/W: WRITE BYTES: 1024

DBUS SOURCE: ADDR

TESTER MODE: R/W TESTER SELF-TEST, OFF Press the TESTER RESET button on the CAT Box.

Controller

Working RAM (ICIO) Check

Check the Working RAM of the game PCB as follows: 1.

2. Perform the preliminary set-up procedure. Enter address DOOO on the CAT Box keyboard. Check that D000 is shown on the ADDRESS/SIGNA- TURE display of the CAT Box. Set R/W MODE to PULSE and then back to (OFF) Set R/W to READ. Set RAW MODE to PULSE.

  • Check the COMPARE ERROR light-emitting diode (LED) on the CaT Box. If this LED is off, the game Working RAM is okay. If this LED is turned on, first check that all interconnections between the CAT Box, Interface Adapter, and game PCB are correctly and securely made. Then repeat parts 1 through 6 of this procedure. If the COMPARE ERROR LED lights up again, check the game Working RAM for failure.

Display RAM (IC154—185) Check

Check the Display RAM of the game PCB as follows:

  • Perform the Preliminary Set-Up Procedure.
  • Perform the Working RAM Check.
  • Set the following CAT Box switches as indicated: R/W: WRITE R/W MODE: (OFF) DBUS SOURCE: DATA BYTES: 1
  • Write FF to address E000. ‘To write data from the CAT Box to the game memory, first set R/W to WRITE. Then, enter the hexadecimal address with the keyboard on the CAT Box. Check that the address shown in the ADDRESS/SIGNATURE display of the CAT Box is correct. Then press the DATA SET button and enter the hexadecimal data with the keyboard on the CAT Box. Check that the data shown in the DATA display is correct. Then set R/W MODE to PULSE and back to (OFF) to send the data to the game memory address shown in the ADDRESS/SIG- NATURE display.
  • Write 07 to address C800 and 40 to address CA00. Then write OE to address C800 and 08 to address CAQ0O0.
  • Set BYTES to 1024.
  • Write 00 to addresses 8000, 8400, 8800, 8C00, 9000, 9400, 9800, 9C00, A000, A400, A800, ACOO, BO0O, B400, B800, and BC00.
  • Check that a section of the game display is erased when the R/W MODE switch is used to write data to each of the above addresses. The erasing begins at the top of the display and proceeds downward by sections.
Page 4

Troubleshooting Guide

Troubleshooting with Checksums

NOTE The following procedure can only be done with those CAT Boxes equipped with a Checksum Switch.

Program ROM (IC1-—4) Check

1. Perform the CAT Box preliminary set-up.

  • Set the CAT Box switches as indicated: BYTES: 256

DBUS SOURCE: DATA

R/W MODE: OFF

CHECKSUM SWITCH: ON

R/W: READ

  • Key in the address pattern given in Table 1 (use 0000 to start). 4, Set the RAY MODE switch to PULSE and then back to (OFF).
  • Check the CAT Box ADDRESS/SIGNATURE display for the appropriate checksum.
  • Repeat steps 3 through 5 for each address listed in Table 1.

Table 1 Program ROM Checksums

ADDRESS ROM TESTED CHECKSUM

0000ROMO29E0
2000ROM18FF8.
4000ROM247CA
6000ROM3C594

Troubleshooting with Signature

Analysis

NOTE The signatures checked in the following procedure are printed in color on the Game Microprocessor and Address Decoders schematic diagrams shown on Sheet 6A and 6B in the Schematic Package Supplement.

Address Bus Lines and Address Decoders Check

1. Perform the CAT Box preliminary set-up. Arabian

Connect the three BNC-to-EZ clip cables supplied with the CAT Box to the SIGNATURE ANALYSIS CONTROL START, STOP, and CLOCK jacks of the CAT Box.

Connect the three black EZ clips to the ground bus bar adjacent to the Game Microprocessor ICI5. Set the CAT Box switches as indicated:

TESTER MODE: SIG TESTER SELFTEST: OFF PULSE MODE: LATCHED START: Positive-going edge trigger STOP: Positive-going edge trigger CLOCK: Positive-going edge trigger Press TESTER RESET on the CAT Box.

Connect the CAT Box Signature Analysis probe tips as indicated: START: pin 12 of ICI16 STOP: pin 12 of IC16 CLOCK: pin 14 of 1C36 Verify the set-up connections by connecting the DATA PROBE to the Game Microprocessor IC15, The CAT Box ADDRESS/SIGNATURE display should show 0000. Now connect the DATA PROBE to the +5V bus adjacent to the Sound Microprocessor IC27. The ADDRESS/SIGNATURE display should show OOUP.

NOTE While testing decoders and ROMs, adding 270 pF capacitors to AB12, Al3, Al4, and Al5 may be necessary to eliminate unstable signatures.

Probe the IC pins with the DATA PROBE and check for the signature indicated in color on the Game Microprocessor and Address Decoders schematic diagrams (Sheet 6A and 6B).

Page 5

Arabian. Troubleshooting Guide

Signal Name Descriptions for Arabian

AO~AI5 Address bits on Microprocessor Address Bus lines AO-A15 are generated by Game Microprocessor ICIS. These bits are buffered by ICI6, IC21, and IC22 to produce the bits on ABO-ABIS. They are also used as the address bits for Program ROM IC1-IC4. AB

Signal AB is the blue playfield data generated at pin 10 of shift register RAM dataon DDO-DD3. This occurs when ENA goes high. The AB signal

IC140in the Video Output Decoders circuit when LDISFT goes low. Data into the shift register is multiplexed by IC/41 from the playfield dynamic

is processed in the Video Output circuit, ABO-ABI5 Address bits on Buffered Microprocessor Address Bus lines ABO-ABIS are software generated by Game Microprocessor ICI5 and are buffered by ICI6, IC21, and IC22. The bits on lines ABO-AB2 and AB9-ABI5 are the select input signals for Address Decoders ICI7, ICI8, C31, and IC32. (Refer to the Memory Map to determine which addresses activate the various Address Decoder output signals.) The bits on lines ABO-ABIO are multiplexed with those on lines OA0-OAI0 in the Custom I/O Microprocessor RAM circuit by 1C23-1C25 to produce the address bits for 1C10. The bits on lines ABO-AB13 are multiplexed with the output count of IC51, C70, IC 49, and 1C68 of the Dynamic RAM Address circuit to produce the bits on ABX0-ABX13 at the outputs of IC52, IC7], 1C53, and 1C72. In the Game Microprocessor circuit, ABIS is gated with CS1 to produce the enable for data-bus buffer 1C28.

In the Watchdog Enable circuit, AB14 is one of the control signals used to generate the WAIT signal for Game Microprocessor IC15. ABHF The active low-level ABHF signal is software-generated by Sound Microprocessor C27. This signal is gated through 1C189 to control the blue shading when the playfield is written. ABPO-ABP12 The picture ROM address bits on lines ABPO-ABPII are generated by counters 1C46, 1C65, and IC47 in the Picture ROM Address Decoders circuit.

The bit on ABPI2 is generated by flip-flop 1C66. These lines carry the address bits for the Picture ROM.

ABXO-ABX13, The buffered DMA address bits on lines ABXO-ABXI3 are generated by multiplexers 1C52, IC53, IC71, and IC72 in the Dynamic RAM Address circuit. These bits are the address inputs for Dynamic RAM Multiplexers IC130-IC133. ‘ACASO The active Iow-ievel ACASO signal is generated at pin 8 of ICI04 in the Row/Column Address Select circuit, This is the column address select for the Red/Shade Playfield RAM. ACASO is active low when CAS is high. ACASI

The active low-level ACASI signal is generated at pin 6 of IC104 in the

Row/Column Address Select circuit. This is the column address select, for the Bluc/Green Playfield RAM. ACASI isactive low when CAS is high. AG

Signal AG is the green play field data generated at pin 10 of shift register

1C142 in the Video Output Decoders circuit when LD/SXT goes low. Data into the shift register is multiplexed by 1C143 from the playfield dynamic RAM data on DD4~DD7. This occurs when ENA goes high. The AG signal is processed in the Video Output circuit. AGHE The active low-level AGHF signal is software-generated by Sound Microprocessor IC27. This signal is gated through C99 to control the green shading when the playfield is written, AR

Signal AR is the red playfield data generated at pin 10 of shift register RAM dataon DDO-DD3. This occurs when ENA goes high. The AR signal

ICI35 in the Video Output Decoders circuit when LD/SFT goes low. Data into the shift register is multiplexed by IC134 from the playfield dynamic

is processed in the Video Output circuit. ARASO ‘The active low-level ARASO signal is generated at pin 11 of 1C104 inthe Row/Column Address Select circuit. This is the row address select for the Red/Shade Playfield RAM. ARASO is active low when RAS is high. ARASI ‘The active low-level ARASI signal is generated at pin 3 of IC104 in the Row/Column Address Select circuit, This is the row address select for the Blue/Green Playfield RAM. ARASI is active low when RAS is high. ARHF ‘The active low-level ARHF signal is software-generated by Sound Microprocessor IC27. This signal is gated through IC99 to control the red shading when the playfield is written. AVO-AV14. ‘The Video Address bits on lines AVO-AVI4 are generated by counters 1€95, IC96, and flip-flop IC129 in the Clock, Sync Chain, and Timing Signals circuit. These bits are used to generate BLNK, INT, VSYNC, and TRGA. In the Dynamic RAM Flip Address circuit, these bits are used to produce the flipped address bits when the game is in the cocktail mode. AV6' The bit on AVG' is generated at pin 4 of ICIII inthe Clock, Sync Chain, and Timing Signals circuit by inverting the bit on AVG. This signal functions as a horizontal blanking signal by disabling multiplexers IC141, 1C143, 1C134, 1C136, ICI51, IC153, IC144, and 1C146 in the Video Output Decoders circuit during video blanking, AVXO-AVX13 ‘The flipped video address bits on lines AVX0-AVXi3 are developed in the Dynamic RAM Flip Addresses circuit from the bits on AVO-AV13. ‘These signals are used, when the game is in the cocktail mode, by Dynamic RAM Multiplexers [C130-IC133. AWO-AW3 — The active low-level write enable signals on lines AWO-AW3 are generated by IC121 in the Dynamic RAM Write Enable circuit from the bits on DBO-DB4 and DISO-DIS3. AWO-AW3 write enable the Red/Shade Playfield RAM. AZ Signal AZ is the playfield shading data generatedat pin 10 of shift register IC137 in the Video Output Decoders circuit when LD/SFT goes low. Data into the shift register is multiplexed by IC136 from the playfield dynamic RAM data on DD4-DD7. This occurs when ENA goes high. The AZ signal is processed in the Video Output circuit. BB Signal BB is the blue motion-object data generated at pin 10 of shift register IC150 in the Video Output Decoders circuit when LD/SFT goes low. Data into the shift register is multiplexed by IC151 from the playfield dynamic RAM dataon DDO-DD3. This occurs when ENA goes high. The BB signal is processed in the Video Output circuit, BCASO The active low-level BCASO signal is generated at pin 8 of 1C106 in the Row/Column Address Select circuit. This is the column address select for the Red/Shade Motion-Object RAM. BCAS0 is active low when CAS is high.

Page 6

Troubleshooting Guide

BCAS1 ‘The active low-level BCASI signal is generated at pin 6 of C106 in the Row/Column Address Select circuit. This is the column address select for the Blue/Green Motion-Object RAM. BCAS| is active low when CAS is high

BG Signal BG is the green motion-object data generated at pin 10 of shift register IC152 in the Video Output Decoders circuit when LD/SFT goes low. Data into the shift register is multiplexed by 10153 from the playfield dynamic RAM data on DD4-DD7. This occurs when ENA goes high. The BG signal is processed in the Video Output circuit. BLNK ‘The active low-level Blanking signal is generated at pin 6 of IC108in the Clock, Syne Chain, and Timing Signals circuit. BLNK is used in the Video Output circuit to turn off gates IC118, IC1I9, 1C120, 1C189, IC98, and IC99 during video blanking. BR

Signal BRis the redmotion-object data generated at pin 10 of shift register

IC145 in the Video Output Decoders circuit when LD/SFT goes low. Data into the shift register is multiplexed by IC144 from the playfield dynamic RAM dataonDDO-DD3. This occurs when ENA goes high. The BR signal is processed in the Video Output circuit, BRASO ‘The active low-level BRASO signal is generated at pin 11 of IC106in the Row/Column Address Select circuit. This is the row address select for the Red/Shade Motion-Object RAM. BRASO is active low when RAS is high, BRAS The active low-level BRASI signal is generatedat pin 3 of IC106 in the Row/Column Address Select circut. This is the row address select for the Blue/Green Motion-Object RAM. BRASI is active low when RAS is high BSEL BSEL is software-generated by Address Decoder 1C31. BSEL is the clock signal for flip-flops 1C90 of the Row/Column Address Select circuit BW0-BW3 The active low-level write enable signals on BWO-BW3 are generated by IC122 in the Dynamic RAM Write Enable circuit. These signals write enable the Blue/Green Playfield RAM. BZ

Signal BZ is the motion-object shading data generated at pin 10 of shift

register 1C147 in the Video Output Decoders circuit when LDISFT goes

low. Data into the shift register is multiplexed by IC146 from the playfield dynamic RAM data on DD3-DD7. This occurs when ENA goes high. The BZ signal is processed in the Video Output circuit. CAS The active high-level Column Address Select enable signal is generated at pin 8 of ICI25 in the Clock, Syne Chain, and Timing Signals circuit. CAS enables 1C104 and IC106 for dynamic RAM column select in the Row/Column Address Select circuit.

CLK4 The CLK4 signal is generated at pin 9 of IC91 in the Clock, Sync Chain, and Timing Signals circuit. This is the clock signal for Custom I/O Microprocessor IC26, via buffer IC38.

COM0-COM5 The active low-level COM0-COMS signals are software-generated by Custom I/O Microprocessor 1C26. These signals are the output enables for buffers ICI1-ICI3 in the Input Bus Drivers circuit. Arabian

Cwo-cw3 Theactive low-level write enable signals on CWO-CW3 are generated by1C123 in the Dynamic RAM Write Enable circuit. These signals write enable the Red/Shade Motion-Object RAM. DO-D7 Microprocessor Data Bus lines D0-D7 form a bi-directional data bus between the Game Microprocessor, the Program ROM, the microprocessor data-bus buffer (IC28), and the Custom I/O Microprocessor RAM buffer (IC9).

DBO-DB7 Buffered Microprocessor Data Bus lines DB0-DB7 form a bi-directional data bus between microprocessor data-bus buffer (IC28), the Coin and DIP Switch Inputs, the Sound Microprocessor, the Dynamic RAM Address, the Picture ROM Address Decoders, the Row/Column Address Select, the DMA Control, and the Dynamic RAM Data circuits. DD0-DD7 Lines DDO-DD7 form a data bus from the dynamic RAM in the Red/Shade Playfield RAM, Blue/Green Playfield RAM, Red/Shade Motion- Object RAM, and Blue/Green Motion-Object RAM circuits to decoders IC134, 1C136, ICAI, 1C143, IC144, ICL46, C151, and 1C153 in the Video Output Decoders circuit. DISO-DIs3

‘The active low-level enable signals on DISO-DIS3 are generated by 1C103

inthe Enable Control Logic circuit, These signals are produced from the picture ROM data and are used to control the outputs of IC121-IC124 in the Dynamic RAM Write Enable circuit. DPBO-DPB3 The blue data bits on lines DPBO-DPB3 are generated by Picture ROM. ICGBO and ICGBIL. These bits are multiplexed with DBO-DB3 by C45, in the Dynamic RAM Data circuit. When EXCT is high, the bits on DPBO-DPB3 are used to generate those on DXBO-DXB3. In the Enable Logic Control circuit, the bits on DPBO-DPB3 are gated by ICi00. DPGO-DPG3 The green data bits on lines DPGO--DPG3 are generated by Picture ROM ICGBO and ICGBI. These bits are multiplexed with DB4—DB7 by IC64 in the Dynamic RAM Data circuit. When EXCT is high, the bits on DPGO-- DPG3 are used to generate those on DXGO-DXG3. In the Enable Logic Control circuit, the bits on DPGO-DPG3 are gated by IC100. DPRO-DPR3 The red data bits on lines DPRO-DPR3 are generated by Picture ROM ICZRO and ICZR1. These bits are multiplexed with DBO-DB3 by IC48 in the Dynamic RAM Data circuit. When EXCT is high, the bits on DPRO-DPR3 are used to generate those on DXRO-DXR3. In the Enable Logic Control circuit, the bits on DPRO-DPR3 are gated by IC102. DPZ0-DPZ3 ‘The shading data bits on lines DPZ0-DPZ3 are generated by Picture ROM ICZRO and ICZR1. These dits are multiplexed with DB4-DB7 by

1C67 inthe Dynamic RAM Data circuit. When EXCT is high, the bitson

DPZ0-DPZ3 are used to generate those on DXZ0-DXZ3. In the Enable Logic Control circuit, the bits on DPGO-DPG3 are gated by ICIOI. DWo-DW3 Theactive low-level write enable signals on DWO-DW3 are generated by ICI24 in the Dynamic RAM Write Enable circuit. These signals write enable the Blue/Green Motion-Object RAM. DXBO-DXB3 ‘The multiplexed blue data bits on DXBO-DXB3 are generated by 1C45 in the Dynamic RAM Data circuit. Theseare input to blue playfield RAM IC174-1C177 and to blue motion-object RAM IC182-IC185,

Page 7

Arabian

DXG0-DXxG3 The multiplexed green data bits on DKGO-DXG3 are generated by IC64 in the Dynamic RAM Data circuit. These are input to green playfield RAM 1C158-IC161 and to green motion-object RAM IC166-IC169,

DXRO-DXR3 ‘The multiplexed red data bits on DXR0-DXR3 are generated by 1C48 in the Dynamic RAM Data circuit. These are input to red playfield RAM 1C170-IC173 and to ted motion-object RAM IC178-IC181 DXZ0-DXzZ3 ‘The multiplexed shading data bits on DXZO-DXZ3 are generated by 1C67 inthe Dynamic RAM Data circuit. These are input to shading playfield RAM 1C154-1Ci57 and to shading motion-object RAMIC162-IC165.

ENA ‘The active high-level ENA signal is software-generated by Sound Micro-

processor IC27. This signal enables the playfield color multiplexers of

the Video Output Decoders circuit via gate C191. ENB ‘The active high-level ENB signal is software-generated by Sound Microprocessor IC27, This signal enables the motion-object color multiplexts of the Video Output Decoders circuit via gate IC191. EXCT ‘The active high-level EXCT signal is developed from the DMA start signal

(aipin 8 of IC5S in the DMA Control circuit) by IC54 and 1C58, EXCT to counters IC49and1C51 in the Dynamic RAM Address circuit. In the

enables trickle input to counter IC43 in the DMA Controi circuit, and

Dynamic RAM Addtess circuit, EXCT also selects theaddress bus for input to multiplexers IC53, 1C72, 1C52, and IC71. Inthe Watchdog Enable circuit, EXCT is used to help generate WAIT. In the Dynamic RAM Data circuit, EXCT selects the picture data bits for output from C45, 1C48, 1C64, and 1C67. EXcT

‘The active Jow-level EXCT signal is developed from the DMA start signal

(at pin 8 of 1C55 in the DMA Control circuit) by [C73. EXCT is the chip select for the Picture ROM. In the Row/Column Address Select circuit, EXCT controls the output of gates ICI16 for dynamic RAM tow and col-

umn selects. In the Picture ROM Address Decoders circuit, this signal

enables the trickle input to counter 1046.

GATE ENABLE ‘The GATE ENABLE signal is clocked out of the Watchdog Enable circuit by K2 atlC91. This signal enables the logic gates at 1C108 for the dynamic RAM row and column select logic. INO-IN3

‘The data bits on INO-IN3 are hatdware-generated by the control panel

and buffered by 1Cl-ICI3 in the Input Bus Drivers circuit. These data bits are input to Custom 1/0 Microprocessor 1¢26. INO, INT The active low-level Input Address Select lines are software-generated by Address Decoder IC32. ‘These are the select enables for IC41 and IC6t in the Coin & DIP Switch Inputs circuit. When low, INO enables the COIN RiNPUT andCOIN L INPUT data through 1C41 to DBOand DBI, and the SELF TEST and Service Switch data through C61 to DB2 and DB3. When low, INI enables the data from DIP switch SW1 to pass through [C41 and IC61 to the data bus. INT The active low-level Interrupt Request is generated every 16 ms at pin 3 of IC92 in the Clock, Sync Chain, and Timing Signals circuit. After inversion by IC75 of the Game Microprocessor cicuit, it clocks through D-type flip-flop 1C74 into pin 16 of Game Microprocessor 1C15. ‘Troubleshooting Guide

TREQ The active low-level Interrupt Request signal is software-generated by Sound Microprocessor 127. This signal is the Interrupt Request for Custom VO Microprocessor C26. Kl The active high-level K1 signal is generated at pin 7 of IC80in the Clock, syne Chain, and Timing Signals circuit. KI is used by [C800 produce the dynamic RAM column address enable signal (CAS). Ki ‘The active low-level Ki signal is generated at pin 4 of [C77 in the Clock, Syne Chain, and Timing Signals citcuit. This isa DMA timing signal for clocking IC49, 1C68, 1C51, and 1C70 in the Dynamic RAM Address circuit; 1C46, 1C65, and 1C47 in the Picture ROM Address Decoders circuit; and 1C34, \C43, and 1C62 in the DMA Control circuit. K1 is gated) by1C57 and IC58 in the Custom I/O Microprocessor Read/Write citcuit to produce the clock for flip-flops C39. Kasi The active low-level KTSI signal is generated at pin 8 of [C78 in the Clock, Syne Chain, and Timing Signals circuit from Kl. in the DMAControl circuit, KTST is gated with K2 to clock IC55. K2 ‘The active high-level K2 signal is generated at pin 2 of IC77 in the Clock, Sync Chain, and Timing Signals circuit. K2 enables parallel counts at 1C46, IC65, and [C47 in the Picture ROM Address Decoders circuit; 1C62 1C43, IC54, and [C74 in the DMA Control circuit; and 1C70, and C51 in the Dynamic RAM Addiess circuit. K2 The active low-level K2 signal is generated at pin 6 of C77 in the Clock, Sync Chain, and Timing Signals circuit. K2 controls Dynamic RAM Multiplexers IC130-IC133 via gate ICII1. Italsois the clock sigaal for Sound Microprocessor 1C27. IDL ‘The active low-level LDL signal is generated at pin 11 of [C73 in the DMA Control circuit, LDL parallel loads counters 1C43 and 1C62 in the DMA Control circuitand counters IC51 and [C70 in the DynamicRAM Address circuit. LDLis inverted by IC75 in the Dynamic RAM Address circuit to enable a parallel count from 1C68 and 1C49. LDASFT. ‘The LD/SFT signal is generated at pin 8 of IC58 in the Clock, Sync Chain, and Timing Signals circuit. When high, LD/SFT toads the dynamic RAM data from the multiplexers of the Video Output Decoders circuit to the associated shift register. When low, it shifts this data out of the shift registers to the Video Output circuit.

MR The active low-level Microprocessor Read signal is generated at pin 11 of 1C20 when the Game Microprocessor is reading from the data bus. MR occurs when both MREQ and pin 21 of [C15 are low. Inthe Address Decoders circuit, MR enables {C32 In the Watchdog citcuit, MR is decoded with other control signals to produce WAIT. In the Game Microprocessor circuit, itis gated with PRD by 1C54 to produce the direction signal for data-bus buffer 1C28. In the Program ROM circuit, MR is the output enable signal for {C1-IC4, In the Custom 1/0. Microprocessor RAM circuit, MR is gated through IC56 and IC35 to enable [C10.

MREQ The active low-level Memory Request signal is generated by Gane Microprocessor IC15 and buffered by IC19. This signal indicates that the bits on the microprocessor address bus are valid for a read or write operation. MREQ is gated with the active RD or WR output from the Game Microprocessor to enable [C20 to produce MR or MW. MREQ is also used to enable IC75 and [C187 of the Watchdog Enable circuit

Page 8

‘Troubleshooting Guide

MW

‘The active low-level Microprocessor Write signal is generated at pin 3

of 1C20 when the Game Microprocessor is writing to the data bus. MW

occurs when both MREQ and pin 22 of ICIS are low. In the Address Decoders circuit, MW is the enable signal for IC31. In the Watchdog Enable circuit, MW is decoded with other control signals to produce WAIT. In the Custom I/O Microprocessor RAM circuit, MW is

used fo enable IC10 fora write operation (via gates C56 and1C35) and

also determines the direction of data flow through buffer IC9. OA0-OA10 The address bits on OAO-OA10 are generated by Custom 1/0 Microprocessor IC26. These bits are multiplexed by IC23-1C25 to produce the address for Custom I/O Microprocessor RAM ICI0. OR The active low-level OR signal is generated at pin 8 of 1C56 in the Custom I/O Microprocessor Read/Write circuit whenever Custom I/O Microprocessor 1C26 requests a read from IC10. OR is gated by 1C35 to enable the Custom I/O Microprocessor RAM (IC10). It also clocks flipflops 1C37 to pass data into the Custom I/O Microprocessor. ow ‘The active OW signal is generated at pin 3 of [C56 in the Custom I/O Microprocessor Read/Write circuit whenever Custom/O Microprocessor 1C26 requests to write data to IC10. OW is gated by 1C35 to write enable 1C10, OW enables Custom I/O Microprocessor buffer 1C36 via inverter 1C57,

PRD The active low-level Priority Read signal is generated at pin 11 of ICi87 whenever the Game Microprocessor requests to read data from the data bus. PRD is gated with MR by IC54 to determine the direction of data flow through data-bus buffer [C28. PRD also is a control signal for the output logic gates of Sound Microprocessor 1C27.

PROM ENABLE The PROM ENABLE signalis generated by flip-flop IC66 in the Picture ROM Address Decoders circuit from the data on DB4. When low, PROM ENABLE enables an output from Picture IC84 and 1C85. When high, it is inverted to enable an output from Picture ROM C86 and IC87.

PWR The active low-level Priority Write signal is generated at pin 3 of C187 whenever the Game Microprocessor requests to write data to the data bus. PWRis a control signal that enables Sound Microprocessor 1C27 for output.

RAS ‘The active high-level Row Address Select enable signal is generated at

pin 6 of IC76 in the Clock, Sync Chain, and Timing Signals circuit. RAS dress Select circuit, RAS enables IC104 and IC106 for dynamic RAM row

is gated by IC77 and IC58 to develop LD/SXT. In the Row/Column Ad-

select.

RBO-RB3 ‘The data bits on RBO-RB3 are generated by Custom 1/O Microprocessor IC26 and buffered by 1C36. These data bits are latched by IC37 to provide the input data bits for the Custom I/O Microprocessor. In addition, RBO-RB3 are sent to Custom 1/O Microprocessor RAM ICI0, RD The RD signal is generated by Custom 1/O Microprocessor 1C26. RD enables buffer 1C38 in the Custom I/O Microprocessor circuit and logic gates 1C35 in the Custom I/O Microprocessor Read/Write circuit. RD is the data input for 1C40, which uses it to produce OR.

RD(H) The active low-level RD(H) signal is software-generated by Address Decoder IC31. RD(A) clocks flip-flop IC66 and parallel loads counter 1C47 for the high address byte of picture ROM data for DMA in the Picture ROM Address Decoders circuit. Arabian,

RDG) The active low-level RD(L) signal is software-generated by Address Decoder 1C31. RD(L) parallel loads buffered data into 1C 46 and 1C65 in the Picture ROM Address Decoders circuit for the picture ROM data lowbyte address for DMA. RESET The active low-level RESET signal is generated by transistor TR3 in the Game Microprocessor circuit. This is the reset signal for Game Microprocessor 1C15, Sound Microprocessor 1C27, and Custom 1/O Microprocessor IC26. In the Custom I/O Microprocessor RAM Control circuit, it presets flip-flop 1C59. ROMO-ROM3, The active low-level Read-Only Memory Chip Select lines ROMO-ROM3 are software-generated by address Decoder ICI7. These are the chip select signals for Program ROM ICI-IC4. SELIM The SELM/II signal is software-generated by Custom I/O Microprocessor 1C26. This signal is used in the Dynamic RAM Flip Addresses circuit to flip the video fora cocktail game. In the Video Output Decoders circuit, SELI/I is inverted by IC75 to produce the data select signal for multiplexers 1C134, IC136, 1C141, IC143, IC146, ICI51, and 1153. SET The active low-level SFT signal is generated by IC80and inverted by IC60 in the Clock, Syne Chain, and Timing Signals circuit. SFT enables shift registers 1C135, IC137, IC140, IC142, 1C145, IC147, IC150, and IC152 of, the Video Output Decoders circuit to be loaded or shifted, depending on the state of LD/SFT. SG0, 5G1 The active low-level Sound Generation signals are software-generated by Address Decoder IC32. SG0 control the address and data latch select logic gates for Sound Microprocessor [C27. SGI controls the input/outputselect logic gates for Sound Microprocessor IC27. SRES The active low-level Sound Reset signal is software-generated by Sound Microprocessor 1C27. SRES is gated with RESET by 1C58 to control the reset input of Custom I/O Microprocessor IC26. TRGA The active low-level horizontal syne signal (TRGA) is generated at pin 8 of IC129 in the Clock, Sync Chain, and Timing Signals circuit. TRGA clears IC96 and is gated through 1C120 for further processing by the video display. SYNC Theactive low-level Vertical Sync signal is generatedat pin 8 of 194 in the Clock, Sync Chain, and Timing Signals circuit. VSYNC is gated by IC120 in the Video Output circuit to develop COMPSYNC. VSYNC is inverted by IC188 to produce VSYNC for further processing by the video display. wair Theactive low-level Wait signal is generated at pin 8 of IC128 by decoding the control signals input to the Watchdog Enable circuit. WATT is buffered by IC19 and applied to pin 24 of the Game Microprocessor, IC15. WE The active high-level Write Enable signal is generated at pin 9 of C133 in the Dynamic RAM Multiplexer circuit. This is the signal that enables 1C195 in the Dynamic RAM Write Enable circuit. WR The WR signal is generated by Custom I/O Microprocessor 1C26. WR enables logic gates 1C35 to produce the chip select for Custom 1/0. Microprocessor RAM ICIO, In the Custom I/O Microprocessor Read/Write circuit, WR is the data input for 140, which uses it to produce OW.

Page 9

Arabian

WR(H) — The active low-level WR(H) signal is software-generated by Address Decoder IC31. WR(A) parallel loads buffered data into 1C49 and 1C68 in the Dynamic RAM Address circuit for the bit map RAM high-byte starting address for DMA. WR) The active low-level WR(L) signal is software-generated by Address Decoder 1C31. WR) clocks IC69 and IC50 to pass data to counters [C70 and ICS inthe DynamicRAM Address circuit for the bit map RAM lowbyte starting address for DMA. XAO-XA6, ‘The dynamic RAM address bits on lines KAO-XA6 are generated by the Dynamic RAM Multiplexers and used to address the Red/Shade Playfield RAM, the Blue/Green Playfield RAM, the Red/Shade Motion-Object RAM, and the Blue/Green Motion-Object RAM. XGHIL

‘The XGHIL signal is generated at pin 8 of C76 in the Clock, Sync Chain,

and Timing Signals circuit. This signal is used by the Dynamic RAM Multiplexers (IC130-IC133) to flip the video by selecting flip video addresses. ‘Troubleshooting Guide

x¥@) The active low-level X¥(A) signal is software-generated by Address

Decoder 1C31. X¥(A) presets flip-flop 1C55 inthe DMA Control circuit

for the picture size high-byte and DMA start. xY¥O The active low-level XY(L) signal is software-generated by Address Decoder iC31. X¥(L) clocks flip-flops 144 and IC63 in the DMA Control circuit for the picture size low-bytes and DMA starts. ® The & signal is generated by 1C80 in the Clock, Sync Chain, and Timing Signals circuit at a 2.5 MHz rate. This signal is inverted by 1C77. ® clocks Game Microprocessor ICI5 through buffer 1C36. Itis also used 10 clock data into Custom I/O Microprocessor RAM IC10 via flip-flop 1C59.