Challenger
Challenger (Centuri, 1981) · Manual · 50 pages · 34 sections · original scan
SERVICE MANUAL
eee centuri 374-10-0100 . inc.
CHALLENGER
CENTURI, INC,
245 W. 74TH PLACE
HIALEAH, FLA. 33014
CUSTOMER SERVICE:
TEL. #(305) 558-5200 (IN FLORIDA)
TEL. #(800) 327-7710 (OUTSIDE FLORIDA)
TELEX: 803694 ANSB CENTURI CABLE: CENTURI
It.
Itr.
Iv. CHALLENGER
TABLE OF CONTENTS
INTRODUCTION: PAGE NO. USER INFORMATION... 2. eee cece cere renee eee cece eect aeeteee sever es end FRONT VIEW CHALLENGER CABINET (FIGURE 1).....eceeceecceeceereeeeendd FRONT VIEW CABINET PARTS LIST FOR FIGURE 1........-++0-- Po Tee esoad
GAME DESCRIPTION SUMMARY........----- bee eee eee see eee wee eee ed
OPERATION: GAME INSTRUCTIONS AND POINT SCORING.........- eee eee eens sce eee 5 OPTIONAL SWITCH SETTINGS....... pce ee eee bee eee eee eee wee ee 6 SYSTEMS DIAGNOSTICS...... ccc ee eect cece eect steer ee ceeeee nec e 859
SPECIFICATIONS: INSTALLATION AND ELECTRICAL REQUIREMENTS... .++eeeeeeeeeeceeeeee +10
ROUTINE MAINTENANCE AND SERVICE......--+6- ee rere So
110/220 VAC CONVERSION INSTRUCTIONS.......- eee eee see eee aeve eld
110/220 VAC CONVERSION DIAGRAM(FIGURE 2)........-+--- see eens 013
GAME PART DRAWINGS, PART LISTS, AND SCHEMATICS FRONT PLATE EXPLODED VIEW(FIGURE 5)..... ereer ere es eee e eee wee eee 14 FRONT PLATE EXPLODED VIEW PARTS LIST FOR FIG. 5.....-.-+-- ceeeee 15
COIN DOOR EXPLODED VIEW OF OPERATING MECHANISMS (FIGURE 6)........16
COIN DOOR EXPLODED VIEW PARTS LIST FOR FIG. 6
COIN DOOR EXPLODED VIEW(FIGURE 7)...... os COIN DOOR EXPLODED VIEW PARTS LIST FOR FIG. 7.
SHINDENGEN POWER SUPPLY PARTS LIST....-.--+-+- PERIPHERAL INTERFACE BOARD A-30(374-13-0100) PARTS LIST......---- 22
VIDEO INTERFACE BOARD A-20(374-13-0200) PARTS LIST........-
AUDIO COMPUTER BOARD A-25(374-13-0300) PARTS LIST.......+--+-- MICRO COMPUTER BOARD, REV. C (374~-13-0400) PARTS LIST. CHALLENGER CONTROL PANEL & PARTS LIST(FIGURE 3)....
CHALLENGER CONTROL PANEL HARNESS (374-12-0500)..... GAMMA II COIN DOOR MODIFIED (374-10-0400)....-.. sees ee cree ee er ecee COIN DOOR HARNESS (374-10-0400) .... eee eee reece eee eceee ELECTROHOME & WELLS-GARDNER MONITOR SIGNAL HARNESS (374-12-0300)..30
P.C.B. POWER HARNESS (374-12-0600).....-..----
D.C. OUTPUT POWER HARNESS (374-12-0200)......- SPEAKER OUTPUT POWER HARNESS (374~-12-0400).. PERIPHERAL POWER HARNESS (374-12-0700) AUDIO BOARD FLAT CABLE HARNESS (374-12-0100)
Iv. CHALLENGER
TABLE OF CONTENTS
GAME PART DRAWINGS, PART LISTS, AND SCHEMATICS (CONT'D): PAGE NO.
PERIPHERAL BOARD FLAT CABLE HARNESS (374-12-0900).............
VIDEO BOARD FLAT CABLE HARNESS (374-12-1000).
CABINET POWER HARNESS (370-12-0200A).........
SHINDENGEN POWER SUPPLY (363-17-0300)..... ay
COMPLETE GAME LESS PKG. (374-01-0200)....... ce eee e cece cee GAMMA II PERIPHERAL INTERFACE BD. SCHEMATIC (374-17-0100)......... Al
GAMMA II AUDIO COMPUTER BOARD SCHEMATICS (374-17-0300)......... 42,43 GAMMA II VIDEO INTERFACE BOARD SCHEMATIC (374-17-0400)..........0% 44
GAMMA IIC MICRO COMPUTER BOARD SCHEMATIC (374-17-0200)............45
Ir
CHALLENGER UPRIGHT
(figure 1]
NO.
1.
10.
ll.
12.
13.
14,
15.
16.
17.
18. CENTURI P/N: CABINET
(FIGURE 1)
PARTS LIST
DESCRIPTION:
361-06-0100
343-03-0200
361-10-0200
374-06-0100
374-06-0500
361-004-1000
374-06-0200
374-06-6300
374-10-0400
361-12-0900A MARQUEE BOTTOM HOLD DOWN BRKT.
MARQUEE TOP HOLD DOWN BRKT.
VINYL TRIM, 7 1/4" LONG
SILK SCREENED MARQUEE PANEL
SILK SCREENED MONITOR OVERLAY
VIEWING GLASS
LEFT HAND SIDE DECAL
RIGHT HAND SIDE DECAL
ONE PLAYER BUTTON
WARP BUTTON
LEFT MOTION BUTTON
RIGHT MOTION BUTTON
TWO PLAYER BUTTON
FIRE BUTTON
CONTROL DECK WIRED ASS'Y.
SUPER BOMB BUTTON
COINCO COIN DOOR (MODIFIED)
A.C. LINE CORD HARNESS
CHALLENGER
CHALLENGER is the newest video game to be introduced by Centuri. With its vivid colors and lively setting, it is sure to lure the most ardent player into game action. The game consists of sixteen sectors(rounds) of play. Sector one begins with Large Energy Rings floating randomly across the screen. The Spaceship must avoid colliding with the Rings, or it will explode into a starburst of brilliant colors. The Spaceship dodges the Energy Rings by moving right or left across the playfield, while bursting them with the Spaceship's 3-directional guns. Bursting the Large Rings (100 points), breaks them into Medium Rings. Bursting the Medium Rings (200 points), breaks them into Small Rings. Bursting the Small Rings (400 points), causes them to disintegrate. The Spaceship is further protected by a feature called a “Warp" button. By depressing this button, the Spaceship will relocate from the top or bottom of the screen to the opposite side. If the Spaceship is in ultimate danger of being destroyed, releasing its Super Bomb will wipe out all the objects on the playfield, and add the point value of the objects to your score. Use of the Super Bomb is lost, if the ship is destroyed first. Only one Super Bomb is awarded per Spaceship. At any time a colorful Space Bogey resembling a Worm may appear on screen and proceed to chase the Spaceship. If the Worm is destroyed by Spaceship fire, or dodged sucessfully for several seconds, a "clang" is heard and the Worm(500 points) wriggles off the screen in a bright red hue of embarrassment. If the Spaceship is caught by the Worm, a bell is sounded, and the astronaut is chased out of his ship in pursuit of safety. At random time intervals a Bonus Bug will walk across the playfield, stop, and count down a Bonus Number. This number is equal to i100 times its value. To receive this Bonus, the Spaceship must link with the nose of the Bonus Bug. When the Spaceship has survived 50 Seconds of playing time, it now enters the challenges of the next sector. The remaining 15 sectors are played in the same manner as Sector one. The differences include that each succeeding sector increases in difficulty. The Energy Rings increase in number and move faster across the screen making them harder to dodge. Also there are several Space Bogeys introduced in the first 8 sectors. They also increase in number with advancement through each sector. Some of the Space Bogeys resemble Comets whizzing through space. Others resemble Spaceships from other worlds. Each Space Bogey(500 points), is an assemblage of bright colors, and when destroyed, burst with a "clang" into a spray of bright light. Sectors 4, 8, 12, and 16, are alike as follows. A few seconds after the Energy Rings are broken into smaller pieces, they are pulled into a Black Hole in the center of the screen. While swirling across the game area, the condensed Rings expand and_ shatter into fragments which must be destroyed before they absorb the Spaceship. When Sector 16 has been accomplished, it will return to Sector 9. When Bonus levels are achieved, an additional Ship will be added to
your game.
CHALLENGER INSTRUCTIONS
BURST ENERGY RINGS TO SCORE AND INCREASE BONUS LEVELS.
LARGE RINGS - 100 POINTS MEDIUM RINGS - 200 POINTS SMALL RINGS - 400 POINTS
AFTER ALL THE SMALL RINGS ARE HIT, ADVANCE TO THE NEXT SECTOR.
IN EACH SECTOR, SPACE BOGEYS APPEAR AND SCORE 500 POINTS WHEN HIT.
WHEN THE BONUS BUG WALKS ACROSS THE PLAYFIELD AND STOPS, BONUS POINTS ARE COUNTED DOWN. TO COLLECT THE BONUS, LINK THE SHIP WITH NOSE OF THE BUG.
PRESSING THE WARP BUTTON IMMEDIATELY RELOCATES THE SHIP FROM THE TOP OR BOTTOM OF THE PLAYFIELD TO THE OPPOSITE SIDE.
THE SUPER BOMB BUTTON DESTROYS ALL OBJECTS ON THE PLAYFIELD SCREEN AND AWARDS TOTAL POINT VALUE TO YOUR SCORE.
ONE SUPER BOMB IS AWARDED PER SHIP. USE OF IT WILL BE LOST IF THE SHIP IS DESTROYED FIRST.
GAME IS OVER WHEN ALL THE SHIPS HAVE BEEN DESTROYED.
200 POINTS 400 POINTS 100 POINTS
OPTIONAL SWITCH SETTINGS
The optional switch settings for the game are found on the C.P.U. Board. They will aid you in your game selection format. Dip Switch A controls the number of coins per game, and also the the number of ships allotted per game. The following settings can also be found described on mode 6 of the self diagnostic test modes. (See System Diagnostics section for further explanation.)
DIP SWITCH A
Switches 1 and 2, of this switch, control the number of coins per game:
| SWITCH 1 | SWITCH 2 | COINS PER GAME |
| oft | off | 1 Coin per game |
| on | Of£t | 2 Coins per 1 game ar |
3 Coins per 2 games
| oft | On | 2 Coins per game |
| On | On | Free Play |
Switches 3 through 6 are factory settings. They are to remain in the OFF position.
Switches 7 & 8 control the number of ships allotted per game:
| SWITCH 7 | SWITCH 8 | NO. OF SHIPS PER GAME |
| Off | off | a |
| on | off | 4 |
| off | on | 5 |
| on | on | 6 |
Dip Switch B controls the number of points at which a Bonus Ship is awarded, as well as some factory settings also described on mode six of the self diagnostic test modes.
DIP SWITCH B
Switches 1 through 3 control the Bonus Ship for different point levels.
| SWITCH 1 | SWITCH 2 | SWITCH 3 | BONUS SHIP AWARDED AT |
| On | on | on | 30,000 Points |
| off | off | off | 40,000 Points |
| on | off | oft | 50,000 Points |
| off | on | oft | 60,000 Points |
| on | on | Off | 70,000 Points |
| off | oft | On | 80,000 Points |
| On | Off | On | 90,000 Points |
Switches 4 & 5 are factory settings and remain in the OFF position. Switches 6 & 7 are factory settings which remain in the ON position. Switch 8 - OFF for the upright game; ON for the Cocktail Table-
SYSTEMS DIAGNOSTICS
Programmed into the Challenger game is a feature called "Systems Diagnostics". This is a series of system level (game level as opposed to circuit level) tests which are used to aid a service operator in checking-out or setting-up a game on site. Regardless of the state of the game or position of the operator switch settings, entry into the test modes is possible as long as the power is on in the game. This is accomplished by depressing the test switch located on the inside of the coin door. By pressing this switch down, a momentary action results which advances you through the selection of test modes. By pressing the switch up, it is now placed in a detent position. This position is used in performing special tests within some of the modes. To exit from the test modes, activate the coin-switch or slam-switch, upon which the game automatically returns to the attract mode. Please note that test mode 7 is used to test the coin switches and exit from it can only be accomplished by stepping to another test mode or interrupting the power with the switch in a neutral position.
The test modes are numbered 0 through 9, with Mode 0 displaying the "diagnostic menu". This is merely the Table of Contents of all of the test modes. The following is a brief description of each of the nine mode selections: COLOR FIELDS (Mode 1) This test is comprised of a built-in, color bar generator. It is used to properly set-up the color monitor for color purity, static and dynamic convergence, and white balance. When Mode 1 is first entered the screen is all black with "TEST NO. 1 COLOR FIELDS" inscribed across the top. When the test switch is placed in a detent position (upward), the screen will automatically sequence cyclically through the 8 color fields (solid color rasters) of RED, GREEN, YELLOW(RED & GREEN), BLUE, MAGENTA(RED & BLUE), CYAN(GREEN & BLUE), WHITE(ALL ON), BLACK(ALL OFF). Any of these color fields can be selected by returning the test switch to a neutral position.
COLOR_GRIDS (MODE 2) This test displays crosshatch patterns. As in Mode 1, the switch in a detent position can be used to select any of the eight colors. The color grids fill the total image display on the monitor screen, so that size and position adjustments of the grid relate directly to the game image. These grids should be periodically used to check the monitor set-up for IMAGE SIZE, POSITION, SYNCHRONIZATION, LINEARITY, PINCUSHIONING, COLOR CONVERGEANCE, COLOR BALANCE. Image focus and brightness should be a final adjustment made on-site to the game, while in play.
CONTINUOUS VIDEO CLEAR (MODE 3) The function of this test is to provide repetitive clear and write signals, so that the functions can be observed with synchronous test equipment such as oscilloscopes. When Mode 3 is entered, the
screen will go solid blue with "TEST NO. 3 CONT'. VIDEO CLEAR" displayed across the top in black. After a 2 second delay, the screen will begin flashing, indicating that repetitive "clear to blue" signals are being processed.
CONTINUOUS VIDEO WRITE (MODE 4) When the test in this mode is entered, the monitor screen will be cleared to all black and "TEST NO. 4 CONT. VIDEO WRITE" will be displayed across the top of the screen in white. After a 2 second delay, a white diagonal line will appear from the upper-left to the lower-right screen. Although not apparent to the viewer, this line is being constantly redrawn to force the video X-Y write counters to cycle through binary up-counts. Since the video RAMS are being continuously accessed, errors from defective or marginal RAMS will appear as spurious dots on the screen, and when errors are observed, the next test mode can then be entered to determine which RAMS are generating the erroneous dots.
VIDEO RAM LOCATOR (MODE 5) Mode 5 is a unique diagnostic aid that uses the video display as well as the hardware configuration of the video computer to isolate problems down to chip level. There are 48 video RAM chips which are socketed and arranged in three groups of 16, corresponding to the 3 primary colors: Red, Green, and Blue. Whenever one of these chips is defective, spurious dots will appear on the screen. For this test, vertical, white lines are spaced across the screen, and 3 pairs of letter-numbers appear in the middle of the screen. These pairs are "road-map" locators corresponding to the physical location of the 3 specific RAM chips on the video board. The locators are displayed in Blue, Green, and Red, and correspond to the 3 RAMS which generate the vertical white lines. If any of the white lines overlaps a noise dot, the locator indicates which chip generated that dot. By moving the test switch up and then back to neutral immediately, the next set of RAMS is selected. The vertical lines appear wider since a second set of lines is drawn adjacent to the first set, and the RAM locators change to indicate the new set of RAMS which generate the new lines. Once again, if these white lines overlap a noise dot, then the locator will tell you which chip is generating that dot. Activating the test switch to the detent position (upward), then back again to neutral can be repeated 16 times total. This process continues adding white lines to the screen until the entire image area is covered with white lines. It is helpful to experiment with this test by removing one of the RAM chips and find its location by using the video locator.
DIP SWITCHES (MODE 6) Test Mode 6 serves a dual, first by checking the proper operation of the option DIP switches(A & B), and second by displaying all the possible switch options. The DIP switch positions are numbered and followed by the word OFF in Red. When a switch is turned ON, it will be written in Green, following the switch number. The best way
to verify proper operation of the DIP switches is as follows:
- Turn all switches OFF.
- Confirm all 16 OFF is displayed.
- Turn all odd-numbered switched ON.
- Confirm alternating ON-OFF is displayed.
- Turn all remaining switches ON.
- Confirm all 16 ON is displayed.
- Turn all odd-numbered switches OFF.
- Confirm alternating OFF-ON is displayed.
- Turn all switches OFF.
- Confirm return to all 16 OFF.
For various selections of the switch options, see the OPTIONAL SWITCH SETTINGS section of this manual.
COIN & START SWITCHES (MODE 7) In this display, as in the previous test, the switches are numbered and followed by word OFF (in Red) or ON (in Green) when the switch is activated. There is also an additional column labeled LOCATOR, which provides the information concerning the connection of each switch to its harness. FOR EXAMPLE ONLY: If the SLAM switch locator is A30J1-4, this means that this switch is wired to Pin 4 of of Connector J1 on assembly A30. When the SLAM switch is activated, the display should show COIN-DOOR switch number 3 ON. If it doesn't connect a jumper from the common of the connector to Pin 4. If the display shows ON, the problem is external to the computer system. Each of the switches listed in this test display should be manually activated to verify proper electrical connections. However, most of these switches are critical switches, and the only true test of total operational performance is by actual use in a game environment. FOR EXAMPLE, multiple coins should be inserted in the coin-slot with the verification of proper tracking of the coins all the way to cash box, through proper credit accumulation and coin counting. Note that the SELECT TEST switch cannot be directly tested in this mode since its activation will sequence to the next test mode.
PLAYER SWITCHES (MODE 8)
The display format for this test is identical to test 7, except that it displays the player 1 and player 2 control switches. This test is also used to isolate problems, but performance testing must be obtained by operating the switches while playing an actual game.
AUDIO COMPUTER (MODE 9) This test lists all the 15 sounds in the Challenger game. By putting the switch in the detent position(up), a sequence of sound effects will be heard. If the proper response is received by the Game Computer, the test will display OK in Green after the sound number. If not, it will write NO in Red. Either response indicates that the request was made. Thus this test provides a check on the Game-to Audio Computer link, when the sound system is not working or not properly connected.
INSTALLATION
Your game was shipped from the factory in ready-to-play condition. A brief inspection is suggested before the machine is removed from the carton. If there is damage to the shipping
carton, contact the freight carrier for claim purposes. External damage could indicate possible damage to the cabinet and/or electronics components.
After the carton has been satisfactorily inspected, remove the machine from the shipping carton.
Examine the interior of the game for disconnected wires, cables, or harnesses. Make sure the electronic devices are securely mounted in their sockets, etc. Record the game serial number since it will be required for reference and servicing.
ELECTRICAL REQUIREMENTS
Unless otherwise specified, this game is set to operate at 110 Volts A.C. See Figure-2~ and 110/220 VAC conversion instructions.
Power Supply Chasis schematic information and parts list are included in this manual.
ROUTINE MAINTENANCE & SERVICE
Because of the solid state electronic circuitry, this machine should require very little maintenance and only occasional adjustments. However, it is necessary to take measures to insure this.
The volume control is labeled, and located in the middle of the cabinet, and can be accessed through the rear cabinet door.
The video monitor has been properly adjusted before shipping. Occasionally minor adjustments are necessary. See monitor specifications and schematics for technical information. Adjustment controls for the monitor are located on the rear of the monitor.
This machine should be serviced only by a qualified technician.
Do not make any adjustments on this machine while power is on.
For service information, contact the Customer Service Department. The number and information is located on the first page of this manual.
POWER SUPPLY The Computer Board in this game operates most efficiently and reliably when the power supply is set so that the voltage on the board is 5.0 Volts, +0.1 Volts. To check this, place a meter across the 5 Volts and ground at the edge of the connector. If necessary, adjust the screwdriver control on the power supply so the meter reads between 4.9 and 5.1 Volts.
110/220 VAC CONVERSION INSTRUCTIONS
This video game has a harness configuration that allows the machine to be operated from either a 110 VAC or 220 VAC, 50 or 60 Hz power source. All games shipped from Centuri, Inc., are in the 110 VAC configuration. To change to the 220 VAC configur-
ation perform the following:
FIRST: Unplug the machine from the wall outlet to completely eliminate shock hazards.
SECOND: Remove the single 3 AMP slow-blow fuse in the A.C. Distrubution Bracket, and install two(2) 1.5 AMP slow-blow fuses. Now cut the #18 AWG. white jumper wire at both ends of the fuse holder and replace the cover.
THIRD: Locate the "orange" jumper plug marked 110 VAC on the game power transformer, on the floor of the machine. Unplug the “orange” jumper, and plug in the "red" jumper plug marked 220 VAC.
To change back to 110 VAC, replace the components changed in
Steps above.
*
(SEE ALSO FIG. 2, 110/220 POWER INTERCONNECT DIAGRAM, #370-10-040C
ENTIAL 4OUT THE FIGURE 2
Hofz20vK. INPUT 9 uy
220 VAC CONVERSION
D.C. PWR, AC BRT S) 5
ELECTRONICS CHASSIS
b + REV. ECN LET. al NO. ASSEMBLY NO
HIALEAH, FLORIDA 33014
110/220 v PIER INTERCONNECT DVAG MATL'S. [eat TREAT, FINISH TE =8- DWN. DA’ SCALE PART NO. REV. a 370-/0-0400 FRACTIONS DECIMALS 2 PL DECIMALS 3 PL
HOLES
ANGLES SHT. MET BENDS .003
REVISION BY < » Ay g
€ Wit Lt ee
Index
PERUZeCorvaMaene
a 2800-0 FRONT PLATE EXPLODED VIEW 25¢ COIN
Description
25¢ Coin Acceptor #4-40 Self Locking Nut Coin Inlet Chute Assembly 4x 3/8 Screw Lamp Socket #47 Lamp (6.3 Volt) Fastener Inner Panel/Lever Assembly Coin Return Button Assembly Coin Return Button 25¢ Price Decal Reject Cover Button (25¢) #4 x 5/16 Pan Head Screw #10-24 Hex Nut (Mounting Hardware) #10-24 x 1-1/8 Carriage Bolt (Mounting Hardware) Index No. Part No.
904588 904590 Description
Coin Inlet Housing Coin Return Cover Coin Return Door Frontplate Assembly, 3-1/8" x 9-1/4" Coin Return Chute Assembly Bar Keeper 4-40 x 3/4 Screw Switch & Wire Assembly Retainer Switch Wire-Silver Switch 6-32 x 3/16 Screw 12 Volt Crem Assembly Switch Cover
2800-0 FRONT PLATE EXPLODED VIEW
(FIGURE 5)
PARTS LIST
| NO. | CENTURI_ P/N: | MANUFACTURING P/N: | DESCRIPTION: |
| 1. | 50270144 | 5031-10 | 25¢ COIN ACCEPTOR |
| 5. | 50270169 | 904717 | LAMP SOCKET |
| 6. | 50270170 | 904716 | #47 LAMP (6.3 VOLT) |
| 8. | 50270172 | 404464 | INNER PANEL/LEVER ASS'Y. |
| 10. | 50270145 | 904591 | COIN RETURN BUTTON |
| 11. | 50270146 | 904703 | 25¢ PRICE DECAL |
| 12. | 50270147 | 904589-2 | REJECT COVER BUTTON (25¢) |
| 16. | 50270149 | 904588 | COIN INLET HOUSING |
| 17. | 50270157 | 904590 | COIN RETURN BEZEL |
| 18. | 50270150 | 904599 | COIN RETURN DOOR |
| 19. | 50270173 | 404463 | FRONTPLATE ASS'Y. (31/8"x9%" |
| 21. | 50270168 | 905115 | BAR |
| 25. | 50270141 | 900651 | RETAINER |
| 26. | 50270142 | 904710-1 | SWITCH-WIRE, SILVER |
| 27. | 50130061 | 904845 | SWITCH |
| 29. | 50270165 | 404354 | 12 VOLT C.R.E.M. ASS'Y. |
| 30. | 50270164 | 904762 | SWITCH COVER |
index No. Part No.
404429
400-8 904782 904706
904822 404352 400-4 904722 904762 100-6-3 404354
904936 100-4-12 404353
900651 2800 SERIES COIN DOOR EXPLODED VIEW
25¢ U.S. COIN
FIGURE 6
Description
Inner Panel With Levers Sub-Assembly Nut Toggle Switch Test Switch Decal Custom Harness Assembly Insulation Coin Counter Assembly (6 Volt D.C.) Nut Wire Key Holder Switch Cover Screw C.R.E.M. Coil Assembly. 12 Volts D.C. Keeper Screw Coin Switch Assembly for U.S. 25¢ Coin Retainer \ =
Description
Silver Switch Wire — for U.S. 25¢ Coin Switch Coin Chute Coin Return Box Switch and C.R.E.M. Coil Bracket Assembly 25¢ Acceptor Bar Screw Miniature Bayonet-Base Lamp. Socket #47 Lamp (6.3 Volt) Coin Inlet Chute Sub-Assembly Right Half of Coin Inlet Chute “U"-Type Fastener Screw Slam Switch Assembly
2800 SERIES COIN DOOR EXPLODED VIEW
25¢ U.S. COIN
(FIGURE 6)
PARTS LIST
| NO. | CENTURI_ P/N: | MANUFACTURING P/N: | DESCRIPTION: |
| 1. | 50270160 | 404429 | INNER PANEL w/LEVERS |
SUBASS'Y.
| 3. | 50130062 | 904782 | TOGGLE SWITCH |
| 4. | 50270161 | 904706 | TEST SWITCH DECAL |
| 5. | 364-62-1000A | = | CUSTOM HARNESS ASS'Y. |
| 6. | 50270162 | 904822 | INSULATION |
| 7. | 50270140 | 404352 | COIN COUNTER ASS'Y. |
| 9:,. | 50270163 | 904722 | WIRE KEY HOLDER |
| 10. | 50270164 | 904762 | SWITCH COVER |
| 12. | 50270165 | 404354 | C.R.E.M. COIL ASS'Y. |
(12 VOLT D.C.
| 17. | 50270142 | 904710-1 | SILVER SWITCH WIRE- FOR |
25¢ U.S. COIN
| 18. | 50130061 | 904845 | SWITCH |
| 19. | 50270143 | 904701 | COIN CHUTE |
| 20. | 50270166 | 904598 | COIN RETURN BOX |
| 21. | 50270167 | 404428 | SWITCH & C.R.E.M. COIL |
BRACKET ASS'Y.
| 22, | 50270144 | 5301-10 | 25¢ ACCEPTOR |
| 23. | 50270168 | 905115 | BAR |
| 25. | 50270169 | 904717 | MINIATURE BAYONET-BASE |
LAMP SOCKET
| 26. | 50270170 | 904716 | #47 LAMP(6.3 VOLTS) |
| 27. | 50270171 | 404418 | COIN INLET CHUTE-SUBASS'Y. |
| 31. | 50130063 | 904707 | SLAM SWITCH ASSEMBLY |
Index No.
Oo nao w FIGURE 7
Part No.
404341 404341-1 404348-1
904591 904703 904589-2
904707-1 2800 SERIES COIN DOOR EXPLODED VIEW
25¢ U.S. COIN
Description
Coin Door Only (2 Coin) Coin Door Only (3 Coin) Coin Return Button Assembly for U.S. 25¢ Coin Coin Return Button U.S. 25¢ Price Decal Coin Return Button Cover for U.S. 25¢ Coin Lock Assembly Index No.
T
W Part No.
345-4-5 904588 325-4-4 904590 904599 904581
406-416 904734 404357 Description
Screw Coin Button Housing Screw Coin Return Bezel Coin Return Cover Coin Door Frame, 11-5/8” x 13-3/8" Mounts in a 10-3/8” x 12-3/16" Opening Hex Nut Carriage Bolt Locking Arm Assembly
NO.
10.
il.
12.
15. 2800 SERIES COIN DOOR EXPLODED VIEW
CENTURI_ P/N:
50270152
50270158
50270145
50270146
50270147
50270148
50270149
50270157
50270150
50270151
50270159 25¢ U.S. COIN
(FIGURE 7)
PARTS LIST
MANUFACTURING P/N: DESCRIPTION:
404341
404348-1
904591
904703
904589-2
904707-1
904588
904590
904599
904581
404357 COIN DOOR ONLY (2 COIN)
COIN DOOR BUTTON ASS'Y. FOR U.S. 25¢ COIN
COIN RETURN BUTTON
U.S. 25¢ PRICE DECAL
COIN RETURN BUTTON COVER
LOCK ASSEMBLY w/KEYS
COIN BUTTON HOUSING (INLET HOUSING)
COIN RETURN BEZEL
COIN RETURN COVER
COIN DOOR FRAME (11 5/8"x13 3/8")
LOCKING ARM ASSEMBLY
PARTS LIST - SHINDENGEN POWER SUPPLY
SYMBOL: DESCRIPTION:
v1 TRANSFORMER, SINGLE PHASE, 2A VA
Ll CHOKING COIL, 1.6mH, 1.5A L2, L4 CHOKING COIL, SF-T8-50S-03 L3 CHOKING COIL, SF-HP-2A-03
D1 DIODE, V19G D2 DIODE, VO6C D3, D6 DIODE, 1S1588 D4 DIODE, S15S3 D5, D7 DIODE, 5CH1M D12, D13 DIODE, F113B D14 DIODE, F113B RF1 DIODE, S4VB40(BRIDGE TYPE)
Ql TRANSISTOR, 2SC2504 Q2 TRANSISTOR, 2SD467(B) Q3 TRANSISTOR, 2SC460(B) Q4 TRANSISTOR, 2SA673(B)
Icl INTEGRATED CIRCUIT, RM723DC or HA17723G-02 PC1 PHOTO COUPLER, PS2001
R1 RESISTOR, 2 WATT, 18 OHM R8, R9 RESISTOR, 2 WATT, 47K OHM R3, 1-4 RESISTOR, 2 WATT, 15 OHM R4 RESISTOR, 1 WATT, 56 OHM R12 RESISTOR, 1 WATT, 100 OHM R28 RESISTOR, 1 WATT, 470 OHM R7 RESISTOR, 1 WATT, 0.56 OHM R26 RESISTOR, 1 WATT, 0.82 OHM R23 RESISTOR, 1/4 WATT, 22 OHM R10 RESISTOR, 1/4 WATT, 33 OHM R27 RESISTOR, 1/4 WATT, 68 OHM R2 RESISTOR, 1/4 WATT, 330-470 OHM R22 RESISTOR, 1/4 WATT, 220 OHM R21 RESISTOR, 1/4 WATT, 270 OHM R6 RESISTOR, 1/4 WATT, 330 OHM R11 RESISTOR, 1/4 WATT, 68 OHM R20 RESISTOR, 1/4 WATT, 470 OHM R17 RESISTOR, 1/4 WATT, 680 OHM R19 RESISTOR, 1/4 WATT, 800 OHM R18 RESISTOR, 1/4 WATT, 1.2K OHM RS RESISTOR, 1/4 WATT, 10K OHM R16 RESISTOR, 1/4 WATT, 220K OHM R29 RESISTOR, 3 WATT, 27 OHM R39 RESISTOR, 1/4 WATT, 4.7K OHM R38 RESISTOR, 1/4 WATT, 5.6K OHM R24 RESISTOR, 1/4 WATT, 330 OHM R25 RESISTOR, 1/4 WATT, 150 OHM RV1 VARIABLE RESISTOR, RJ-6P501 USAGE:
PRENNENER FPNE
BPeRR
RH
PRB BRB BBB B BPE RPREEP BRP RE ERR RADE
PARTS LIST - SHINDENGEN POWER SUPPLY
SYMBOL:
cl, c2 c3-1,-2 c9, C10 Cll, ¢23 c12, C13, C15 c27 C18, C19, C20
C21, C22, C25
c14, C16 DESCRIPTION:
CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, ECK-DAL102E 160VSN100 SM10VB-2200 SM10VB-2200 SL25VB-10 SL25VB-10 SM35VB-1000 SM35VB-1000 SM16VB-1000 DMY21H472K DMY21H104K DMY21H222K CM20XC511K5 MDD22G473K DMY21H222K
ENCLOSED TYPE FUSE, 3A USAGE:
PRENEPRPWRPWRPWNNNN
N
374-13-0100
PERIPHERAL INTERFACE BOARD A-30
| NO. | PART NUMBER: | DESCRIPTION: | USAGE: |
| 1. | 50020005 | MPS 6531 NPN SIGNAL TRANSISTOR | 1 |
| 2. | 50020065 | TIP 120 NPN POWER TRANSISTOR | 1 |
| 3. | 50030014 | 270 OHM, 1/4W., 5% RESISTOR | 2 |
| 4. | 50030097 | 2.7K OHM,1/4W., 5% RESISTOR | 1 |
| 5. | 50040010 | O.1mfd, 16V., CERAMIC DISC CAPACITOR | 2 |
| 6. | 50060055 | 100mfd, 16V., ELECTROLYTIC CAPACITOR | 1 |
| 7. | 50230001 | 3 AG., 1 AMP, NORMAL BLOW FUSE | 1 |
| 8. | 50230014 | 3 AG., P.C MOUNT FUSE CLIP | 2 |
| 9. | 50150313 | 4 CKT., P.C. WAFER, MOLEX | 1 |
| 10. | 50150310 | 10 CKT., P.C. WAFER, MOLEX | 1 |
| ll. | 50150312 | 9 CKT., P.C. WAFER, MOLEX | 3 |
| 12. | 50150177 | 20 PIN FLAT CABLE HEADER, STRAIGHT w/EJECTOR 1 | |
| 13’. | 50100007 | 1N40001 SILICON 1AMP DIODE | 1 |
| 14. | 50100014 | 1N914 SIGNAL DIODE | 32 |
| 15. | 50210197 | P.C. BOARD, A-30 | 1 |
374-13-0200 VIDEO INTERFACE BOARD A-20
| NO. PART NUMBER: | DESCRIPTION: | USAGE: |
| 1. 50010002LS | 74LS00 I.c. | 2 |
| 2. 50010004LS | 74LS02 I.c. | 2 |
| 3. 50010005LS | 74LS04 I.c. | 3 |
| 4. 50010007LS | 74LS10 I.c. | 2 |
| 5. 50010008LS | 74LS20 I.c. | 2 |
| 6. 50010019LS | 74LS874 I.c. | 6 |
| 7. 50010024LS | 74LS93 I.c. | 4 |
| 8. 50010028LS | 74LS153 I.c. | 5 |
| 9. 50010045LS | 74LS157 I.c. | 2 |
| 10. 50010059LS | 74LS165 I.c. | 6 |
| 11. 50010105Ls | 74LS32 I.Cc. | 1 |
| 12. 50010194LS | 74LS191 I.c. | 5 |
| 13. 50010014 | 7442 I.c. | 3 |
| 14. 50010191 | MK4027-4, 350ns I.c. | 48 |
| 15. 50030051 | 1K OHM, 1/4W., 5% RESISTOR | 3 |
| 16. 50030095 | 330 OHM, 1/4W., 5% RESISTOR | 2 |
| 17. 50030206 | 180 OHM, 1/4W., 5% RESISTOR | 3 |
| 18. 50040010 | -lmfd, 16V., CERAMIC DISC CAPACITOR | 33 |
| 19. 50040027 | -Olmfd, 16V., CERAMIC DISC CAPACITOR | 1 |
| 20. 50040053 | 100pfd, 25V., CERAMIC DISC CAPACITOR | 10 |
- 50060055 100mfd, 16V., AXIAL ELECTROLYTIC CAPACITOR 3
| 22. 50040066 | 470pfd, 16V., CERAMIC DISC CAPACITOR | 4 |
| 23. 50150111 | 16 PIN SOLDER TRAIL SOCKET, LOW PROF. | 48 |
| 24. 50150178 | 26 PIN FLAT CABLE P.C.B. HEAD w/EJECTOR | 1 |
| 25. 50150310 | 10 CKT., P.C. WAFER, MOLEX | 1 |
| 26. 50150314 | 12 CKT., P.C. WAFER, MOLEX | 1 |
| 27. 50070009 | 11.6688 MH, CRYSTAL | 1 |
| 28. 50210195 | VIDEO INTERFACE BOARD | 1 |
374-13-0300
AUDIO COMPUTER BOARD A-25
| NO. PART NUMBER: | DESCRIPTION: | USAGE: |
| 1. 50010004LS | 74LS02 I.C. | 1 |
| 2. 50010005LS | 74LS04 I.C. | 1 |
| 3. 50010014LS | 74LS42 I.C. | 1 |
| 4. 50010019LS | 74LS74 I.C. | 1 |
| 5. 50010172 | 6502 I.C., C.P.U. | 1 |
| 6. 50010177 | AY3-8910 I.C. | 1 |
| 7. 50010171 | 2716 I.C., EPROM | 1 |
| 8. 50010206 | 6532 I.C. | 1 |
| 9. 50010054 | LM380N I.C. | 1 |
| 10. 50030010 | 470 OHM, 1/4W., 5% RESISTOR | 2 |
| 11. 50030146 | 15K, 1/4W., 5% RESISTOR | 2 |
| 12. 50030112 | 3.3K, 1/4W., 5% RESISTOR | 3 |
| 13. 50030092 | 1 MEG., 1/4W., 5% RESISTOR | 1 |
| 14. 50030051 | 1K, 1/4W., 5% RESISTOR | 2 |
| 15. 50030154 | 2.7 OHM, 1/4W., 5% RESISTOR | 1 |
| 16. 50030150 | 47K, 1/4W., 5% RESISTOR | 1 |
| 17. 50030063 | 10K, 1/4W., 5% RESISTOR | 1 |
| 18. 50040010 | 0.1mfd, 16V., CERAMIC DISC CAPACITOR | 16 |
| 19. 50040011 | .001lmfd, 16V., CERAMIC DISC CAPACITOR | 1 |
| 20. 50040056 | .05mfd, 16V., CERAMIC DISC CAPACITOR | 1 |
| 21. 50040085 | 22pfd, 16V., CERAMIC DISC CAPACITOR | 1 |
| 22. 50060060 | 10mfd, 16V., AXIAL ELECTROLYTIC CAPACITOR | 1 |
- 50060055 loomfd, 16V., AXIAL ELECTROLYTIC CAPACITOR 3
- 50060090 2.2mfd, 16V., AXIAL ELECTROLYTIC CAPACITOR 1
| 25. 50060058 | 2200mfd, 16V., ELECTROLYTIC CAPACITOR | 1 |
| 26. 50130034 | 8 POSITION DIP SWITCH (SPST) | 2 |
| 27. 50150061 | 24 PIN SOLDER TRAIL SOCKET, LOW PROF. | 1 |
| 28. 50150060 | 40 PIN SOLDER TRAIL SOCKET, LOW PROF. | 3 |
| 29. 50150179 | 34 PIN FLAT CABLE HEADER w/EJECTOR | 1 |
| 30. 50230001 | 3 AG., 1 AMP FUSE, NORMAL BLOW | 1 |
| 31. 50230014 | 3 AG., MOUNT FUSE CLIP | 2 |
| 32. 50150311 | 3 CKT., P.C. WAFER, MOLEX | il |
| 33. 50150310 | 10 CKT., P.C. WAFER, MOLEX | i, |
| 34. 50070005 | 3.579 MHz CRYSTAL | 1 |
| 35. 50090015 | 14 PIN DIP HEAT SINK, V7-1, STAVER | 1 |
| 36. 50120005 | 100K, 1/4W., TRIMMER POT | 1 |
| 37. 50210196 | AUDIO COMPUTER BOARD, A-25 | 1 |
MICRO COMPUTER BOARD, REV. C 374-13-0400
PARTS LIST
| NO. PART NUMBER | DESCRIPTION: | USAGE: |
| 1. 50010002LS | 74LS00 I.c. | 1 |
| 2. 50010005LS | 74L804 I.c. | 4 |
| 3. 50010019LS | 74LS74 I.c. | 2 |
| 4. 50010273LS | 74LS244 I.c. | 2 |
| 5. 50010195LS | 74LS367 I.Cc. | 1 |
| 6. 50010248LS | 74LS138 I.C. | 2 |
| 7. 50010045LS | 74LS157 I.C. | 1 |
| 8. 50010035LS | 74LS161 I.c. | 1 |
| 9. 50010172 | 6502 I.C., CPU | 1 |
| 10. 50010173 | 6522 I.c. | 3 |
| 11. 50010322 | 2532 I.C., EPROM 500ns or LESS | 6 |
| 12. 50030007 | 100K., 1/4W., 5% RESISTOR | 1 |
| 13. 50030010 | 470 OHM, 1/4W., 5% RESISTOR | 2 |
| 14, 50030063 | 10K., 1/4W., 5% RESISTOR | 3 |
| 15. 50030112 | 3.3K, 1/4W., 5% RESISTOR | 3 |
| 16. 50040010 | -lmfd., 16V., CERAMIC DISC CAPACITOR | 14 |
| 17. 50040011 | -001mfd., 16V., CERAMIC DISC CAPACITOR | 9 |
| 18. 50040056 | -O05mfd., 16V., CERAMIC DISC CAPACITOR | 1 |
- 50060055 100mfd., 16V., AXIAL ELECTROLYTIC CAPACITOR 1
- 50060124 1.0mfd., 16V., AXIAL ELECTROLYTIC CAPACITOR 1
| 21. 50070005 | 3.579MH,, CRYSTAL w/LEAD WIRES | 1 |
| 22. 50130034 | 8 POSITION DIP SWITCH (SPDT) | 3 |
| 23. 50150061 | 24 PIN SOLDER TRAIL SOCKET, LOW PROF. | 8 |
| 24. 50150060 | 40 PIN SOLDER TRAIL SOCKET, LOW PROF. | 4 |
| 25. 50150112 | 18 PIN SOLDER TRAIL SOCKET, LOW PROF. | 4 |
| 26. 50100014 | 1N914 SIGNAL DIODE | 1 |
| 27. 50150177 | 20 PIN FLAT CABLE w/EJECTOR | 1 |
| 28. 50150178 | 26 PIN FLAT CABLE w/EJECTOR | 1 |
| 29. 50150179 | 34 PIN FLAT CABLE w/EJECTOR | 1 |
| 30. 50150310 | 10CKT. P.C. WAFER, MOLEX | 1 |
| 31. 50010310 | 2114 RAM | 2 |
| 32. 50210194c | MICRO COMPUTER BOARD, REV. C | 1 |
| 33. 374-10-0300 | EPROM LABELS | 6 |
AF 17899¢ CONTROL PANEL 4S OE woz EPS NUT 1011 00 22 |#/0-24x36 CARRIAGE BolT BLACK OX/DE | i 50/3 0049! RED BY7TON ASS CZ 50/3 0050 | PAL NUT i 50730047 | SWITEH | 3G/-10-0600 | H/NGE CONTROL PECK [10110023 |#10-24x12 CARRIAGE B0CT, BLACK OK/DE | Bi 37d-03-0/00 | CONTROL PANEL 374-06-0400 CONTROL PANEL WWERLA _$0/30048 | WHITE BUTTON ASSY PART VE DESCRIPTION
BILL OF MATERIALS
[Oooks | NNN] shoe ASSNS S|
I- PLAYER 2- PLAYER. CRIMP TERMIWAES CHAIN SET. FEMALE Houswa mocax
2 50150274 50150309 WHITE WIG B2LAWG, VIOLET wi EFA AWG ELE Oly Me BLUE VIRE * 22AWG_ GREEN WIRE *22AwG BLACK WIRE #22 AWG SUL OF MATERIALS
CONTROL PANEL HARNESS
farce Tees TRE. aw by Biee/ Be [Sxdev2-a500
fey. ter. ge REVISION wv AF 17899¢
SAA SW NiO.
RIGHT COIN Sw
NOTES
QO moneares simyvet
WIRE CONN. TO OM SIDE
OF TEsT SW.
@ INDICATES CUT ON
WHITE WIRE TO ON SIDE OF TEST SW
OF TEST SW.
® INDICATES CUT AND REMOVAL
OF WH/YET WIRE FROM POINT X TO NOT USED* RIGHTLAME ONO. |\eerr con Sw LEFT ERP Nor use0 & Oc. APD SS Se
++ REV. LET. REVISION TOLERANCES: canton. HIALEAH, FLORIDA 33014
RANE GAMMA IE COIN DOOR MODIFIED FF e14-0700 [Re [ewe Eas [Cind S700 [B¥#10- 0400)" AF 178998
)
4 i
- T[COLA Tessa
\ RIGHT COIN F406, SLAM Sw. [11 Do Test A SELECT TEST ‘| 7” \ EFT COIN [5508]
oe ;
® a] Cc 3, GND
fata
L
Hal. £
NOTES ALL WIRE IS *22 AWG
RECEPTCALE Ae. == ‘AamaNmLY RO
RIPTION Tora a cantDAl. ee
Ey EOIN DOOR HARNESS
8a! AF 17a99C
NOISIA3Y O080-TI-hui ON Lava:
F ‘Wesiwwio3a sto + WeSsivwil3aa ¥ ‘SNOLLOVUS NOLL THOS3C [oN
Q wr TT SI SUIM TY (2LON
OT PRC YEOH yy O00 MS F% Cope a MU bb 90bbi
peas Nee
‘On AvawaESY | “Ai0 | G.aav“00Ma | GAw 20 lorto-10-Kle Wy Big SI FYIM TY I7LON
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
HIALEAH, FLORIDA 33014
FRACTIONS
DECIMALS 2 PL
DECIMALS 3 PL : SPEAKER OUTPUT HARNESS
HOLES — MATL'S. [neat TREAT. FINISH ow. ME “ es [Ble Bare." E2- orool™
SHT. MET BENDS +
REVISION
weeeci av
DECIMALS 2 PL + J
DECIMALS3PL + 4
HOLES:
ANGLES: + W2
SHT. MET BENDS + z
veee.i av
LET. NO. REVISION
veseii av
TOP VIEW
FRONT VIEW
2" | 2 {s0isoiee | 34 PUN STERIN ELIEF
FRACTIONS.
DECIMALS 2 PL 015 DECIMALS 3 PL
HOLES
REV. LET.
REVISION
ANGLES
SHT. MET BENDS. oa
TOP VIEW
[2 | 2 | 50/80/22 | 2ZOPW FLAT CABLE Comm.
- |22% 50/70023 | ZOPIN FLAT CABLE _ Te TY, PART 2 | DESCRIPTION
BILL OF MATERIALS
2 | 50/50/46 | 20 PIN STRAIN RELIEF
FRONT VIEW TRA,
TOLERANCES
HIALEAH, FLORIDA 33014
FRACTIONS
DECIMALS 2 PL
DECIMALS 3 PL HOLES ANGLES SHT, MET BENDS + z NAME PERIPHERAL BD. FLAT CABLE HARNESS
LL
REV. ECN Rey | NO. REVISION HHH LH
we6ec) Av
ff —————_
TOP VIEW
rT
FRONT VIEW
212 | S$0/80123 | 26 PW COMM __ f" |50/70024 |26COWDCABLE lL DESCRIPTION
BILL OF MATERIALS
ee. HIALEAH, FLORIDA 33014
VIDEO FLAT CABLE HARN&ES |
FRACTIONS
DECIMALS 2 PL
DECIMALS3PL + ae ‘ mars HEAT TREAT. FINISH sneer sens; 2 [Ps by (Bios [Re [87F12-1000|""
vee. REV. “! Ler. REVISION
Bla SAwG te |atentrs0o4 reer sheparbionbace ae © Bhp [13 e650 Violek, Wigel3 Aws 1267450 | Green Wine 3 dws | 115745017004] Whike Wine FAW rebrand Black wine” 13 AWG
SPEAKER
SCREEN
#01 | A.c. INPUT TO aw: Pe 3-4 ZSOLATION TRANFORMER a oy, 628 513 0150105 SOA wanna oe PS ape Mp\ex
DECIMALS 2 PL
DECIMALS 3 PL
me AE Bal
ANGLES
+ + + oan £
SHT. MET BENDS +
we [a é ve 45vec com my B [eanas Havoc ro] we 12] con 033 SC7RO. 7 } Setter RB “doh
2 TIPI20
Ag Aa Aa az Ag.
| walt | WAVAVAVAYA | Yv¥ yy | AVA | AVA, “4 y | VY |
& si[afalz|e[s|e}s|el/ vole sla] 3|2}/ slele7fell22)1 > ]el7lelelelelel
| y Beas < | & | hoe | NY ype | gy | |
| 8 | eS5 3g | ae 8 | & | i | g x |
| 8 geo 8 | ub | OS | WR | 88 | |
| COIN DOGR | CAME | DO NOT USES | PLAYER 1€2 | ||
| SU/TCHES | CONTROL | SWITCHES |
SUITEHES, 4 al TOLERANCE rr Tate es = err _ ipeomssanaety ae) GAMMA IE PERIPHERAL (TERME G4. t es paar nant —[ Fo we _nevinon wy |e anon |" [Rw ig 17-o100]
[Aer efron REVISIONS
| pa 3s | ecw | DISPOSITION | ||||
| ~ | la | | | aie | 8] 2] No. | DESCRIPTION | OF existing |22 |
| LF | we. | gels | pants |S % | |||
| Sethe | She | Fi choad el |
ier
| 25. | ak | eamucs | ilae |
| at | Lf | ow | |
| 7476 | + | oF o.o~ |
ances .
| : | aa | i |
feo, A ASS [8
| ay | 8, | =) |
RIRRRERS | a TEN Tu ete PS ¢, rade i
| 2 | VQe | | | Af_@ | |||
| 7 | ale | i | - | we | ||
| it | alg | | | ess | «| | i | 9, |
; ge__<) Hf ssp ta Mm a\3 i
| = | a | an | oon | 1 |
| — | - | Th | ||
| + | fl | i | = | |
| H | t | nb |
7 23x + xix
| = | + | i | To |
+ = re
| — | ; | + | , |
£4
%;
| i | in | afelalalafeleitetsteld | aisist_ SISIRISIR} |
| Bee | ee | 1g TS 8Szl | ggg Sug Ry |
| cpu | TSLUE Et | 2 Psat | |
| Be | Reysgessysg | BESPTVe IVs | |
| Lt | Ra | SRP appiafelsis | slg |
| + i
+ +
| is | + | =e |
lela ol 2 NUTHIENI SS BSNY sysera,
| qeselyeseysial | 3 | _ |
‘lel i | slele ia ] u | pce * souolge REVISION DATE: 8-9 280 Hel " y s ‘ 8 WATERIAL OF
| FRO AJOTS | ov ine assy ]OWG No. | womencrature | __|cowm'erantno| _srock swe __| _rimist_Jrnocess}vcar aca |
| NCa VEAZ | bi | ALLIED LEISURE INOUSTRIES INC. |
i unctss orwenwst seccwee| 1780 W, 4th AVENUE HIALEAH, FLORIDA 33010. frmcuons 3 1 ame: Ganwa eT Cans we Oe EO, | ARS AUO1e COMPUTER #2. AchisT
| a | mous, | Seg fa | re |
| NEXT ASSEMBLY. | ANGLES tL, | Su |
rr
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
FI (ANB 412 Voe o™~
AUDIO AMPLIFIER
ALL CAPS IN HFO @16V L
PCB 50210196 cB AE S3 10K + RG 1 or aE 2200 me = RS 3 BIH iv 7 3 OME ©, Yaw ce Orne Oy
REVISION DATE: J 26-80
@ ©OBGO
QO OGBSBOO
CBO ODDAI® O68) DODDBOO 8
@ ee GOES BOO GO
FIG. F
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ROMS Fi, 61, V1, 02,62, Fefee ALL PINS SAME AS El EXCEPT PIN 20 (EB)
EEEEPEERE SONOOSeas Ls.8 8 =
yeae
cat ro TS wr
al ee
az] we We
vig Ad wens vis az
oo Wa oe yaar Vig on te] vig of ie] Vie oe oF ar] we i" we 27 79] veer Buawk
pe] zene necay 5] een mane be] ware pevsy
Coal Coc. [| 8 fe] com core fF cok Ta eve fy] ae Cou PcBPSO2/0194.C
a] cent. ee Ban. 2 |. nee Stans! [iw Male ber [SS [HE azole]