Pot Shot TM-318 1st Printing
Pot Shot (Qps) (Scorpion 4) (set 1) (Qps, 200?) · Technical Manual · 78 pages · 100 sections · original scan
printing eM " e
«# Fa | Weber: soninton nt fe with Illus'
ATARI
GAMES
Pot Shot» Operators Manual with Illustrated Parts Lists and Schematics
© 1988 by Atari Games Corporation. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035
Printed in the U.S.A 58
Produced by the Atari Games Technical Publications Department
DISCLAIMER Atari Games Corporation does not express nor imply an opinion or a warranty that the Pot Shot game is legal to operate in every jurisdiction, or that this game conforms to every local ordinance or regulation. The operator is solely responsible for ascertaining that the operation of this game in the intended jurisdiction will be in full compliance with all applicable laws, ordinances, and regulations.
Atari Games Corporation disclaims all liability for claims, damages, or penalties resulting from the operation or use of this product whether or not the same is in full compliance with all applicable laws, ordinances, and regulations. >
Notice Regarding Non-Atarie Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game. ° Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
- All ground wires in the game are properly connected as shown in the game wiring diagram,
- The power cord is properly plugged into a grounded three wire outlet.
- On games provided with an Electromagnetic Interference (EMD ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
iii
Table of Contents
Set-Up How to Use This Manual. Inspecting the Game. Levelling the Game. Setting the Anti-Tilt Mechanism Installing the Marquee Installing the Steps... Loading the Firing Balls. Loading the Prize Ball Control and Switch Locations... Coin and Game Option Settings . Game Operation Game Play........ Hits for Game Play Operator Adjustments for Maximum Earnings.. Calculating Payout and Win Ratios. Prize Balls... Carousel Settings Loading Prize Balls .. Game Price..., Self-Test RAM Test ROM Test. Audio Test .. Light Test Firing Ball Delivery Anti-Tilt Mechanism Switch Opiions...... Maintenance Preventive Maintenance. Cleaning the Coin Mechanism .... Checking the Feed Screw Motor Belt. Checking the Feed ScrewPulley and Motor Screws Checking the Gear Assembly Checking the Crank Handle. Cleaning the Ball Receiver Assembly . Removing the Plastic Feed Tub Replacing the Gun O-Ring Adjusting the Firing Tub: Adjusting the Firing Wheel. Cleaning the Game Field... Cleaning the Electronic Components . Cleaning the Bubble Dome and Windows Repaits ...... Unjamming the Gun Motor Adding More Firing Balls... Replacing the Gun Ratchet Assembly Spring Replacing the Gun Pinch Wheel Cushion. Replacing the Gun Support Chain...
Replacing the Gun Diaphragm . Replacing the Gun Firing Tube. Replacing the Gun Firing Motot Replacing the Gun Shot Sensor.. Replacing the Start Switch or Buttot Replacing Lights........ Replacing the Feed Screw Pulley Belt Replacing the Feed Screw Motor . Replacing the Firing Ball Delivery Removing the Game PCB Removing the Speaker. 5 Troubleshooting Mechanical Troubleshooting. Electronic Troubleshooting 6 Illustrated Parts Lists and Schematics See List of Illustrations that follows. Glossary
Figure 1-1 Figure 1-2 Figure 2-1 Figure 2-2 Figure 3-1 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Figure 6-6 Figure 6-7 Figure 6-8 Figure 6-9 Figure 6-10
Table 1-1 Table 3-1 Table 3-2 Table 3-3 Table 4-1 List of Illustrations
Feed Screw Shipping Brace Control and Switch Locations . Factory Carousel Settings for Lage Balls. Increased-Difficulty Carousel Settings for Power Supply and Game PCB Area Ball Reservoir Area .... Firing Ball Delivery Assembly. Firing Assembly .............005 Adjusting the Firing Assembly Unjamming the Motor .. Cabinet-Mounted Assemblie: Pot Shot Gun Assembly. Power Supply Assembly. Coin Acceptors, Inc. Coin Door Assembh Pot Shot Game PCB Assembly Game Wiring Diagram. Power Supply and Coin Door Wiring Diagrams Pot Shot Game PCB Schematic Diageam, Sheet 1. Pot Shot Game PCB Schematic Diagram, Sheet 2 .. Pot Shot Game PCB Schematic Diagram, Sheet 3 ..
List of Tables
Game Specifications Self-Test Results... Coin and Credit Option Settings. Firing Ball Allocation and Attract Audio Setting: Recommended Preventive-Maintenance Intervals ...
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
Shapter 4 bo ains gfeventive spfintenance Y ands f “ Chapter 5 contaigs vole information. parts lists and for ie Pot Shot game, mation required to set om Pot Shot game is not shipped. You must 7 ie marque¢; frant step, add the firing / a put in tye prize balls. YY
are ¥edexnption prizes with your, 5
Set-Up
Inspecting the Game
To avoid electrical shock, do not plug in the cabinet until it has been inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you have only a two-wire outlet, we recommend that you hire a licensed electrician to install a grounded outlet, Players can receive an electrical shock if the cabinet is not properly grounded. Do not touch the printed circuit board with your hands or with metal objects.
Please inspect your Pot Shot game carefully to ensure that the game is complete and delivered to you in good condition. Figure 6-1 shows the location of the primary parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: 1. Examine the exterior of the cabinet for dents, chips, or broken parts. Unlock and open the rear access door to the power supply and game PCB area and the ball reservoir area. Check the following: © Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed connector can damage the printedcircuit board (PCB) and will void your warranty.
- Ensure that all plug-in integrated circuits on the PCB are firmly plugged into their sockets.
- Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected.
1-2 Feed Screw
Ball Reservoir
Shipping Brace
Figure 1-1 Feed Screw Shipping Brace
In the ball reservoir area, remove the wooden shipping brace that holds the feed screw bracket. See Figure 1-1. Check that the belt is tight between the motor pulley and the feed screw pulley. Also check the following screws and nuts to be sure they are tight:
- The two screws holding the motor mount on the cabinet floor. © The four screws holding the motor on the motor mount.
- The socket-head screws on the motor and feed screw pulleys.
- The three screws holding the feed screw shaft to the reservoir.
- The six screws that hold the triangular ball distributor channel on the cabinet. Unlock and open the carousel access doors on the sides of the game. Check that the cotter pins on the top of the carousel shaft are firmly in place.
Unlock and open the gear assembly door on top of the game. Check that the cotter pins are firmly in place. Make sure the socket-head screw holding the motor on the driver gear is tight. Check to be sure the motor bracket screws are tight. Check that the electrical connectors from the motor are firmly plugged in.
Unlock and open the coin doors. Check that the electrical connectors are firmly plugged together on the component bracket inside the door. Inspect the power cord for any cuts or dents in the insulation. Inspect the gun and feed screw for any damage. The gun has been adjusted at the factory and is ready to use. The feed screw never needs adjustment.
Levelling the Game
The game must be level or it will not operate properly —the firing balls will not roll back to the feed screw and the prize balls will not roll to the front to be claimed by the players. 1, The four game levellers are in the spare parts package in the storage compartment. The levellers screw in underneath the game, 1 1/2 inches in from the sides. The location of the levellers is shown in Figure 6-1. Put the four furniture coasters, also in the parts package, under the levellers. Put a bubble level on the bottom of either side window frame to check the level. Screw the levellers in or out to level the game, If you move the game, be sure to check the level of the game before you operate it.
Setting the Anti-Tilt
Mechanism
Set the anti-tilt mechanism to prevent players from tilting the game. The game does not turn off if the game is tilted, but a siren sounds to alert the attendant. 1.
2. Adjust the anti-tilt mechanism after you have installed the levellers. This is described above in Levelling the Game. Turn the thumb screw to loosen and tighten the plumb bob setting on the anti-tilt mechanism. For a very sensitive mechanism, adjust the plumb bob high. For a less-sensitive adjustment, adjust the plumb bob low. Set-Up
If you adjust the plumb bob high, the anti-tilt siren will sound very frequently.
Installing the Marquee
Install the marquee on the top of the Pot Shot game, in front of the gear assembly access door. See Figure 6-1. To install the redemption sign in the marquee, perform steps 1 and 2 and then put in the sign.
- First, remove the four screws holding the black plastic retainer on the marquee. Take off the retainer.
- Remove the glass on the front of the marquee. Unlock and remove the gear assembly door on top of the game, so you can plug in the marquee light electrical connector. 4, Put the marquee on the top of the game.
- Push the electrical connector into the gear assembly area through the large middle hole.
- Using four washers and the four 2 3/4-inch-long hex head screws from the parts bag, screw the marquee onto the game through the holes in the bottom of the marquee.
- Connect the electrical connector for the marquee light. Make sure the electrical harness does not interfere with the gears.
- Close and lock the gear assembly door.
- Install the attraction shield and graphics. Install the retainer,
:
Installing the Steps
Attach the steps so both children and adults can play the game. 1, Put the two brackets of the bottom step against the front of the game cabinet. The end of the left bracket should be 1 3/8 inches from the right edge of the chrome strip on the side of the game.
- Mark where the screws in the right and left brackets will screw into the cabinet.
- Drill six 3/32-inch holes for the screws.
- Use the six 3/4-inch wood screws in the parts bag to attach the step to the cabinet.
Set-Up
Loading the Firing Balls
Two packages of firing balls are shipped with your game in the storage compartment under the play field. Load the large package of 850 balls now. Do not load the smaller package with 100 replacement balls. See Adding More Firing Bails in Chapter 4 for information about adding these replacement balls. 1, Open the rear access door to the ball reservoir area. See Figure 4-1. Turn on the game power. Go to the front of the game, open the coin door, and press down twice on either auxiliary coin switch. (See Figure 1-2 for the location of the switch.) Press the Start button to start the feed screw.
- As the screw turns, slowly add the firing balls in the large package to the reservoir.
- Watch the firing balls returning to the reservoir for several games. Remove some of the firing balls if they are jamming in the flat triangular distributor above the reservoir. If the balls are not returning to the distributor, check that your game is level. If necessary, level it, then check the ball distribution again.
- Close and lock the access door to the ball reservoir area.
Loading the Prize Balls
The prize balls are shipped separately. If you need more prize balls, you can obtain them from your distributor or Atari Games Corporation Customer Service. An illustrated list of approved prize balls, with an order form, is included with this manual. Follow the directions on the order form for ordering. If you do not have this list, call or write Atari Customer Service at the numbers on the inside front cover of this manual.
1-4 The carousel disc heights are set at the factory. Try these settings first if you are using the large size prize balls between 2 7/8 and 3 1/8 inches in diameter. After you have operated with these settings, you may want to make the game more difficult by changing the disc heights.
- Open the carousel access doors on both sides of the game. (These doors have interlock switches on them that prevent the gun from firing while either door is open.)
- Load the prize balls. (if you want to take out any carousel, follow the instructions under Carousel Settings, in Chapter 2.) 3, After you load the prize balls, close and lock the carousel access doors.
Control and Switch
Locations
Power On/Off Switch The power on/off switch is located at the rear of the cabinet. (See Figure 6-1.) Self-Test Switch The self-test switch is located on the shelf behind the upper coin door. (See Figure 1-2.) Use the self-test switch to select the self-test mode to check game operation. Refer to Chapter 3 for a complete description of self-test operation. Volume Control The volume control is located on the shelf behind the upper coin door. (See Figure 1-2.) The volume control adjusts the volume of the sound effects.
Coin Counter The coin counter is located on the shelf behind the upper coin door, (See Figure 1-2.) The coin counter records the number of coins deposited.
Auxiliary Coin Switches
The auxiliary coin switches are located on the lower part of the coin mechanism. (See Figure 1-2.) Press once on either switch to give one coin credit to a player.
Table 1-1 Game Specifications
Characteristic Specification
Power Consumption 285 VA at 120 VAC Temperature 45° to +38° C (437° to +100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games at 60 Hz) Width 33.25 in. (85 cm) Depth 120 in. G05 cm) Height 88 in. (224 cm) Weight 750 Ibs. (341 kg)
Coin and Game Option Settings
The Pot Shot game has two dual inline package (DIP) option switches on the game PC board. (See Figure 3-1.) The switches at 4E on this board control the number of firing balls given in each game and music in the attract mode. Set-Up
The switches at 7D/E select the coin options and game price. Refer to Coin and Game Option Settings in Chapter 3 for information on the coin and credit settings and the game option settings. This section also describes how to set the switches and what the recommended settings are.
‘Component Bracket Assy Coin Counter
Auxiliary Coin: ‘Switches
Coin Door Self-Test Switch Volume Control
Figure 1-2 Control and Switch Locations
ce fads snigiis f tee.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ener quarts”
folls to yet Claims it. i¢._playét shoots a prize sels, the ere the-j the crank.on.-the’ #layer aims a crank-handle. {tioh game based on actual ? ‘nsf
the €2r01 “he she “Gatlidg gun and\tuys ‘control the raté-of fire.
Agi out of one &
e front of the gathe wl ‘. NY LO Va X
XN
ie ROMs; the de thé goin the RAMs, th very
d the ball deli
'S
any : switch as te itermi test by x. / This made m2, éxplained The mo The/ lent mus’
ona ode, exp! had, wa starte
auidio syste: play/mode is
Operating
Game Operation
Game Play
To begin the game, the player deposits the number of coins required for the game (coinage amount is an operator game option), then presses the Start button. The “Hold Your Fire” light begins flashing and the feed screw turns to deliver the firing balls. The plastic feed tube to the gun fills with firing balls. Some firing balls always fall on the game field, but only the balls that enter the plastic feed tube are actually counted. A player always receives the correct number of balls, no matter how many fall on the playfield. While the firing balls are counted, the “Hold Your Fire” light flashes until all of the firing balls for that game enter the plastic feed tube. The player can begin shooting as soon as balls reach the gun, even though the “Hold Your Fire” light is still flashing. Or the player can wait until all the firing balls are delivered and the “Hold Your Fire” light turns off. The player aims the gun at the ball he wants and turns the gun crank handle to control the rate of fire. If the player turns the crank quickly, the balls are fired quickly. The player has unlimited time to shoot the firing balls. When a ball is knocked out of the carousel, it rolls to the front of the game where the player retrieves it. If a player deposits more coins than are required for one game, he can either press the Start button once to receive the balls for only one game or he can press the Start button several times quickly, to receive the balls for all the games at once, If he presses the Start button several times, the plastic tube fills and then the firing balls spill onto the game field, since the plastic feed tube only holds about 100 balls. In this case, the player must begin shooting before the “Hold Your Fire” light goes out since the feed screw will not stop delivering balis until the correct number of balls have entered the plastic feed tube.
Hints for Game Play
To begin, shoot a few firing balls slowly to find out where they will go. Aim at a prize ball and start shooting as the ball rotates towards you. The best place to aim on the prize ball is above the ball-holding disc. Shoot very rapidly at the ball. The ball bounces in the holder under the rapid fire and will bounce and roll out of the holder. Depending on the carousel settings, the easiest prize balls to shoot out are usually in the center of the middle carousel. The more difficult prize balls to shoot out are at the top and bottom comers.
Operator Adjustments for Maximum Earnings
This game has several operator adjustments. To adjust
2-2 the game intelligently, you must keep track of the payout and win ratio each week and change the carousel settings according to this information. Put in new prizes regularly, to keep up player interest. You can also change the game coinage, depending on the value of the prizes. If your location relies heavily on regular customers, you can change this option as you change prizes. This list summarizes what the operator must do to keep earnings high.
- Be sure the prize balls are properly lit. Replace burned-out lights immediately. If the prizes are not lit, players cannot see the prizes nor the results of their shooting and eamings will fali.
- Keep a weekly payout sheet. Adjust carousels as needed. Your weekly payout should be between 25% and 35%. If the payout is lower than 25%, players will feel they are cheated. If your payout is higher than 35%, you are not only giving away too many prizes, but good players, who are the repeat players, will not be challenged by the game. Repeat play is very important for game longevity.
- Calculate the win ratio on the game. The ratio should be between 8 and 12, if the cost of each prize is about $1.00.
- Use only the following types of prize balls: Balls recommended by Atari Games. (See the Prize Bail section below.) Do not use any fuzzy or plush balls, like tennis balls. Do not use plastic capsules. The firing balls will shatter them.
Calculating Payout and Win
Ratios
Your payout should be between 25% and 35%. Your location may have maximum earnings with the payout at the higher or lower end of this range. After operat+ ing the game for a while and tracking the payout, you will know how to adjust the game for maximum earnings. Fill the carousels at regular intervals, and keep track of how many balls you replace. Calculate your payout weekly, particularly when you first set up the game and players are learning how to shoot. After the first week, you will probably want to change to more diifficult carousel settings (shown in Figure 3-2) to continue to challenge your players. For your information, each carousel holds a maximum of 35 balls, with a total of 105 for the entire game. Your win ratio (or “hit frequency”) should be between
8 and 12, if the prize cost is about $1.00. To calculate these numbers, use these formulas: Payout = Cost of Prizes Given Out / Income Win Ratio = Number of Plays / Number of Prizes (where Number of Plays = Income / Coinage).
Prize Balls
Use the prize balls recommended by Atari Games. These are shown on the order forms that come with this manual. If you do not have an order form, contact your distributor, or Atari Games Corporation Customer Service. The Customer Service number is printed on the inside front cover of this manual. If you plan to use balls that have not been recommended by Atari Games, follow these guidelines for choosing the balls. Do not use balls with a plush or fuzzy surface, like tennis balls. These balls are difficult to shoot out and will contaminate the game field, ball reservoir, feed screw, and gun. You will have to repair and probably replace game parts. Do not use the clear plastic capsules that are readily available and can be filled with prizes. These plastic balls will be shattered by the firing balls.
1/4" and 3/4" All between-tier (1" total) spacers are 3 1/2" high (6 places) 1/4° and 3/4" (1" total)
18", 1/4", and 3/4" (1-178" total)
1/4" and 3/4" (1" te
1/8", 1/4", and 3/4" (1 1/8" total)
1/4" and 3/4" (1" total)
L—— 18", 1/4", ena gia" (1 1/8" total) Game Operation
The prizes themselves inside the capsules create two other problems. The prizes have different weights, so the light ones are easy to shoot out and the heavy ones difficult. Also, since the prizes can shift around inside the capsules, it may be impossible to shoot some of the capsules out since the weight is always in the bottom of the capsules. ¢ Prize balls sizes should be between 2 7/8 and 3 1/8 inches in diameter for the ball-holding discs with 3 3/8-inch diameter holes. Prize balls should be between 2 3/8 and 2 5/8 inches in diameter for the ball-holding discs with 2 7/8-inch diameter holes.
- Do not use balls heavier than 2.8 ounces. Balls heavier than 2.8 ounces are extremely difficult, and even impossible, to shoot out.
Carousel Settings
Use different ball sizes in the carousels with different ball-holding discs. You must adjust the carousels differently for the two sizes of prize balls. The carousels set at the factory use the discs with 3 3/8-inch diameter holes-—see Figure 3-1. (Madballs™ use this size disc.) The discs in the carousel spare parts kit have 2 7/8-inch diameter holes.
All three carousels should be set as shown (if you are using Madballs™ throughout).
Figure 2-1 Factory Carousel Settings for Large Balls
2-3
Game Operation
Recommended Settings The factory settings for the ball-holding discs with the 3 3/8-inch diameter holes combine easy and difficult settings on each carousel to give both skilled and unskilled players opportunities to shoot out prize balls. Figure 3-2 shows suggested settings to make the game more difficult. As a rule, you should change to these settings after the payout exceeds 35%.
Changing Carousel Settings
To change carousel settings, add and remove spacers between the ball platform disc and the ball-holding disc. Adding spacers makes the game harder and removing spacers make the game easier. (However, do not make the carousel settings too difficult.) Always use at least the 3/4-inch standard spacer between the discs for any size balls.
Removing a Carousel
- Turn off the game. It is easier to take out the carousels when they are not turning.
- Open a carousel service door on the side of the cabinet. These doors have interlock switches so that the gun cannot fire while a door is unlocked.
All between-tier (1 total) ers are 3 1/2" high (6 places)
(1" total)
1/8", 1/4", nd 3/4"
and 3/4"
18", 1/4",
18", 1/4", id 31 1/4" and 3/4"
1/4" and 3/4"
a1 (1 1/8" total)
114" and 3/4” (1 total)
1a", 1/4", (1-1/4" total)
and 3/ (1 1/8" total)
an (1 1/8" total) 3, Remove a carousel by taking out the cotter pin in the top of the carousel. 4, If you want to operate the game while you have a carousel out, put a piece of tape over the bottom hole.
Taking Apart the Carousel
- Loosen the screw on the top retainer and slide the retainer off. Keep this retainer separate from the other pieces. It must go back on top. Do not take Off the retainer on the very bottom.
- Take the carousel parts off the shaft by sliding the game parts off the top. Leave the bottom retainer at the same place so the bottom platform disc is 6 inches from the play field floor.
- Each carousel has 3/4-inch standard spacers, 3 1/2-inch spacers, platform discs and bali-holding
1" Easy
11 ledium 1 1/ Hard
All three carousels should be set as shown (if you are using Madbalis™ throughout).
Figure 2-2 Increased-Difficulty Carousel Settings for Large Balls
discs on it. The factory-set carousels also have 1/4inch spacers between the discs, and some have 1/8-inch spacers. The carousel kit in the storage compartment has 1/8-inch spacers, 1/16-inch spacers, ball-holding discs for smaller balls and extra cotter pins. Changing Disc Height and Discs Add 1/4-inch, 1/8-inch and 1/16-inch spacers between the ball-holding discs and the platform discs to make the game harder. Remove these spacers to make the game easier,
- We recommend that you set up the carousels with both easy and hard settings to provide a combination of challenges for experienced and beginning players.
- Assemble the carousel with the correct discs for the size of ball you are using, with standard spacers, and with as many extra spacers as you like. Put the top retainer (which has a screw in it) back on top. Press down hard on this retainer to get a tight fit between all the pieces. If you don’t do this, the top platforms may not rotate with the shaft.
- Tighten the screw with a 5/16-inch nut driver. Game Operation
Reinstalling the Carousel
- Turn off the power to the game. Open the carousel service door. If the game has been in operation, remove the tape over the bottom hole.
- Put the carousel back in the game by putting the lower end of the shaft into the bottom hole. Push the carousel into the top sleeve. With a new cotter pin, connect the carousel shaft to the sleeve. Push open the halves of the cotter pin to hold the carousel in place.
Loading Prize Balls
- Open a carousel access door. The gun will not fire while this door is open.
- Load the prize balls.
Game Price
You can change the number of coins required for each game with settings on the DIP switches at 7D/E on the game PCB. You can choose one to four coins required for each game on both coin mechanisms. See Game Options in Chapter 3 for more information. The factory game setting is 2 coins per game. The front instruction panel also reads “1 Play 2 Coins.” If you change the settings on the DIP switches, also changed the coinage label. Coinage labels are included with your game. To replace the coinage label, remove the instruction panel. Information about removing the instruction panel is in Replacing the Start Switch or Button in Chapter 4.
Game Operation
N
2-6 S
self-test the coin
6u do not hear the LD YOUR FIRE” light is en the RAMs failed the didn’t hear a beep,
Self-Test
Audio Test
Press the start switch on the front of the game to go to the audio test. The game passes the audio test if you hear four different sounds and then a steady sound. If you do not hear anything, then you have a problem with the audio ICs, the speaker, or the harness. To turn off the sound and go to the next test, press the Start switch.
If you want to turn the game off after the self-test is finished, first shoot the firing balls so they do not jam the gun motor when you turn the game on again later.
Light Test
When you press the start switch to end the steady tone, you enter the light test. The left and right “Hold Your Fire” lights turn on and off.
Firing Ball Delivery Test
Press the start switch on the front of the game to go to the firing ball delivery test. The feed screw turns and delivers balls to the ball delivery assembly. The ball delivery assembly counts 5 balls and the test ends. If for some reason the feed screw does not deliver any balls to the assembly, the feed screw turns until you switch off the self-test switch. After the balls are counted, the self-test ends. If you press the start switch, the RAMs are tested again. To leave the self-test, switch the self-test switch off.
Anti-Tilt Mechanism
The anti-tilt mechanism is in the back of the game in for the location of the mechanism. When you move the plumb bob on the mechanism, you should hear a siren sound if the mechanism is working correctly.
Switch Options
Pot Shot has two option switches on the game PCB. One 8-position DIP switch is at 7D/E. The other 8position DIP switch is at 4E. These are shown in Figure 3-1.
DIP Switches at 70/E DIP Switches. Pot Shot PCB at4E Assy
Anti-Tilt Mechanism
Fuse Cover Power Supply
Assy Power Supply
Astec Switching
Figure 3-1 Power Supply and Game the power supply and game PCB area. See Figure 3-1 PCB Area
Table 3-1 Self-Test Results
| Test | Pass | Fail | Other |
| RAM | Beep | Right HOLD YOUR | No sound or light |
FIRE light is on. ison. Check speakers and audio ICs.
| ROM | “Boing” sound | Left HOLD YOUR | No sound or light |
FIRE light is on. is on. Check speakers and audio ICs.
| Light | Left and right HOLD YOUR | No lights are on. |
FIRE lights turn on. Audio 4 different sounds, then 1 steady sound. Ball Delivery Counts 5 balls. No sound
Doesn't count
3-2
The switch at 7D/E controls the coin and credit options.
The switch at 4E controls the number of firing balls allotted for each game and turns on and off the attractmode music.
Table 2-2 and Table 2-3 show the options and the recommended settings. The options are set at the factory to the recommended settings. To change the settings, remove the thin plastic covering over the switches. Use a pen or a sharp pointed instrument to slide the buttons to different settings. Up is the on position and down is the off position. The DIP switches at 4E control the number of firing balls allotted for each game and the music in the attract mode. The firing balls are controlled by turning switches off. Self-Test
For example, to give 70 firing balls in each game, set the DIP switches as follows: Switch 1 On
| Switch 2 | of | (40 balls) |
| Switch 3 | OF | (20 balls) |
| Switch 4 | Off | (Oballs) |
Switch 5 On Switch 6 On Total Balls 10 + 20 + 40 = 70 balls
Do not set the DIP switches to give more than 90 balls, because the plastic feed tube to the gun holds only about 100 balls.
DIP Switch Settings at 7D/E on the Pot Shot Game PCB
| 8° | 7 | 6 | 5 | 4 | 3 | 2 |
| On | On | On | ||||
| On | On | Off |
On Off On Off = On On
| On | Off | off |
Off On Off
Off Off Off
On Off
On On On Off
Off On
Off Off
On On Off Off Table 3-2 Coin and Credit Option Settings
“This is the order of the switches on the game PCB as it is installed in the game. Option
Bonus Adder No Bonus Coins # 2 Coins Give 1 Extra Coin 4 Coins Give 1 Extra Coin 4 Coins Give 2 Extra Coins 5 Coins Give 1 Extra Coin 3 Coins Give 1 Extra Coin Free Play (for demonstration)
Left Coin Mechanism 1 Coin Counts as 1 Coin # 1 Coin Counts as 2 Coins
Right Coin Mechanism 1 Coin Counts as 1 Coin # 1 Coin Counts as 4 Coins 1 Coin Counts as 5 Coins 1 Coin Counts as 6 Coins
Game Price” 1 Coin 2 Coins + 3 Coins 4 Coins On Off On On
“This game price ts the number of coins required for each game. However, if your coin mechanism ts set to anything other than “1 coin counts as 1 cotn,” then divide the number of coins each coin counts as by the game price, to find out how many games the player receives for bts coins, For example, if your coin mechanism set to “1 coin counts as 6 coins” and the game price is set to 2 coins, then 6/2 = 3; the player receives 3 games, + Manufacturer's recommended settings
3-3
Self-Test
DIP switch settings at 4E on the Pot Shot Game PCB
| 1 | 2 | 3 | 4 | 5 | 6 | 7 |
| OF | On | On | On | On | On | |
| On | OF | On | On | On | On | |
| On | On | OF | On | on | On | |
| On | On | On | Of | On | On | |
| On | On | On | On | Or | On | |
| On | On | On | On | On | OF |
+ Manufacturer's recommended settings Table 3-3 Firing Ball Allocation and Attract Audio Settings
8 Option
Number of Balls Allocated 5 Balls 10 Ball 20 Balls 40 Balls 80 Balls 160 Balls (DO NOT USE)
Music in Attract Mode Music Plays # No Music Plays
If you set the DIP switches to deliver more than 90 balls, the balls are counted and go into the feed tube until the feed tube fills up. Then no more balls can cross the ball delivery assembly. The feed screw continues to deliver balls, but the firing balls fall on the playfield. When the player fires some of the balls, then balls can cross the ball delivery assembly again and go into the feed tube. The player always receives and is able to fire the number of balls he paid for, since only the balls that actually go into the feed tube are counted. Although the player does receive the proper number of balls, we do not recommend a setting of more than 90 balls per game, since this will confuse players.
, cai ent ‘pre Kom for ment pi rocedusesare
Maintenance
Preventive Maintenance
Preventive maintenance includes checking, cleaning, and adjusting hardware. How often you perform preventive maintenance depends upon the game environment and frequency of play. However, we recommend you check, adjust, and clean the components listed in Table 4-1 at the intervals specified.
Table 4-1 Recommended Preventive- Maintenance Intervals Component Inspection and Maintenance Intervals Inspect whenever you collect coins. Clean at least every three months. Check every 2 months. Replace when worn. Check every 2 months. Adjust when necessary. Check every 2 months. Readjust when necessary. (If you adjust the firing tube, you must also adjust the firing wheel.) Feed Screw Belt & Screws Check every 2 months, Gear Assembly Check every 2 months. Crank Handle Check every 2 months. Ball Receiver Assembly Clean when needed. Bubble Dome and Side Window Coin Mechanism
O-ring
Firing Tube Adjustment
Firing Wheel Adjustment
Clean when needed.
Cleaning the Coin
Mechanism
Use a soft-bristled brush: to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.
4-2
Checking the Feed Screw
Motor Belt
Unlock and open the rear door to the ball reservoir area. (See Figure 6-1.) Check to be sure the feed screw motor belt is tight, shown in Figure 4-1. It should have about 1/2-inch of slack when you pull or push on it. If it does not, tighten the belt. Tighten the belt by moving the motor bracket back and forth.
- Loosen the motor bracket screws on the bottom of the cabinet with a Phillips screwdriver just enough to move the bracket back and forth.
- Move the bracket until the belt has about 1/2-inch of slack. Tighten the screws.
Pulley and Motor Screws Check the socket-head screws on the feed screw pulley and feed screw motor pulley. (See Figure 4-1.) If screws are not tight, tighten them with a 3/16-inch Allen wrench.
Checking the Gear Assembly The gear assembly is located on the top of the game, behind the marquee. Open the top door, shown in Figure 6-1, and check the following items.
Feed Screw Feed Screw Motor Ball Reservoir
Ball Distributor Feed Screw Feed Screw Motor Bracket Pulley Bet ‘Pulley
Figure 41 Ball Reservoir Area
- Check the socket-head screw on the driver gear below the gear motor. If necessary, tighten it with a 5/16-inch nut driver.
- Check the cotter pins on all gears. If any cotter pin is broken, replace it.
- Check the screws on the motor bracket that hold the motor on the bracket and that hold the bracket on the mounting plate. If they are not tight, tighten them with a 3/8-inch nut driver.
Checking the Crank Handle
The crank handle turns a ratchet that makes the gun noise. If the ratchet is loose, the gun will not make much noise when the handle is turned. Check the ratchet wheel adjustment by turning the crank handle backwards. If the handle turns backwards easily, then you should tighten the ratchet wheel screw.
- Look up in the gun from below. Find the hole in the gun body across from the handle. You can see the ratchet wheel inside the gun.
- Rotate the handle until you can see the sockethead screw in the middle of the ratchet wheel. If the crank handle is so loose you can not turn the ratchet wheel, try to turn the wheel with a screwdriver.
- Use a 5/32-inch Allen wrench to tighten the screw. 4, Turn the crank handle backwards to test how much resistance it meets.
Cleaning the Ball Receiver Assembly
If the firing ball delivery assembly (shown in Figure 4-2) is extremely dirty, it should be cleaned so the balls feed smoothly and do not jam.
- Turn off the game power.
- Remove the bubble dome by removing all the tamperproof screws holding the dome on the Sensor Block
Ball Receiver Feed Screw Assy
Plastic Feed
Tube
Figure 4-2 Firing Ball Delivery Assembly Maintenance
game. Lift off the dome by standing on the step, grasping the dome on the right and left sides, and lifting it.
- Wipe the dirt off the ball receiver assembly with a small cloth dampened with isopropyl alcohol or a 1% solution of detergent in water.
Removing the Plastic Feed
If the plastic feed tube is extremely dirty, it should be replaced so the balls feed smoothly and do not jam.
- Turn off the game power. 2, Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome by standing on the step, grasping the dome on the right and left sides, and lifting it.
- Remove the plastic feed tube by taking off the hose clamps and disconnecting the tube from the gun and the ball receiver unit. Slip the tube through the feed tube bracket.
- Replace the tube by slipping the plastic feed tube through the feed tube bracket, putting hose clamps on both ends, and connecting the ends to the gun and the ball receiver assembly.
Replacing the Gun O-Ring
Check the O-ring every 2 months or if the balls are not firing or not firing with enough force. Replace the Oring if it is worn. Always check the O-ring before you make any other adjustments to correct firing problems. If you are only checking or replacing the O-ring, then follow the next procedure. If you are also adjusting the firing tube and the firing wheel, take off the inside gun cover (explained in Adjusting the Firing Tube) instead of opening the top cover.
- Turn off the power to the game. 2, Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome by standing on the step, grasping the dome on the right and left sides, and lifting it.
- Take off the top black cover on the gun by removing the four screws and washers with a 1/8-inch Allen wrench.
- Find the O-ring (see Figure 4-3), and take it off.
- Put the new O-ring on. Make sure it fits into the groove on the firing wheel.
- Put the cover back on the gun and reinstall the bubble dome.
Maintenance
2. Top Black Cover
Inside Gun Cover
(8 places) Firing Tube Nut (3 Places) Gun Cover Stud
Firing Tube Plate
Firing Assembly Bracket
Motor Mounting Bracket
Figure 4-3 Firing Assembly
Adjusting the Firing Tube
The firing tube must be the right distance from the pinch wheel so the firing balls are fed at the correct rate to the firing wheel. If the tube is too far from the pinch wheel, too many balls fall through at once. If the tube is too close to the pinch wheel, the balls may not fall through at all. Turn off the game power. Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome by standing on the step, grasping the dome on the right and left sides, and lifting it. Remove the inside gun cover. Take off the four nuts facing the player side of the game with a 3/8inch wrench. Pull the gun cover towards the back of the game enough to clear the studs. Then slide the gun cover to the left. Finally, pull off the cover towards the back of the game. 4, Disconnect the plastic feed tube from the gun. If you see metal balls in the firing tube above the pinch wheel, turn the crank (with the power off) and then spin the firing wheel by hand. Before you adjust the firing tube, check the cushion on the pinch wheel. Figure 4-3 shows the location of the pinch wheel cushion. You may need to use a flashlight to see the cushion. If the cushion is worn, replace it before doing this adjustment. The procedure is in Replacing the Pinch Wheel Cushion, in the Repairs section of this chapter. Loosen the three nuts that hold the metal feed tube on the firing assembly bracket. (see Figure 4- 3). Use a 3/8-inch socket to remove the two nuts on the top of the plate. Use a 3/8-inch flat wrench to loosen the nut on the bottom, behind the motor. Loosen the nuts just enough to allow the metal plate to slide back and forth.
- Insert the long end of the adjustment tool, shown in Figure 4-4, into the firing tube from the top. Move the metal plate back and forth until the rod is held between the pinch wheel and the metal tube, (It should not be held very tightly.)
- Tighten the nuts.
- To make sure you have adjusted the firing tube correctly, turn the crank handle backwards. The adjustment tool should move up and down when you turn the handle.
- Be sure you have the power turned off, then drop several balls into the gun and turn the crank handle. Check that the balls feed one at a time. 12, Now adjust the firing wheel. Do this because you have probably changed the firing tube height (the mounting holes of the firing tube have vertical play in them). The firing wheel adjustment is described next.
Firing Wheel ‘Adjustment Nut
S Firing Tube
Firing Tube Plate
Short End
Sensor Block
Figure 44 Adjusting the Firing Assembly Maintenance
Adjusting the Firing Wheel
If you have replaced the O-ring or adjusted the firing tube, adjust the firing wheel.
2. Turn off the game power. Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome by standing on the step, grasping the dome on the right and left sides, and lifting it. Remove the inside gun cover. Using 3/8-inch wrench take off the four nuts facing the player side of the game. Pull the gun cover towards the back of the game enough to clear the studs. Then slide the gun cover to the left. Finally, pull off the cover towards the back of the game. Adjust the firing wheel by moving the motor mounting bracket up and down. See Figure 4-3. Loosen the three motor mount nuts with a 3/8inch socket. These nuts are on the motor side of the firing assembly, on either side of the motor. Loosen the nuts just enough to slide the motor up and down. Use the short end of the adjustment tool, as shown in Figure 4-4, and insert it into the metal feed tube beneath the firing wheel. Move the motor until the firing wheel rests on the tool. Tighten the nuts on the motor mount. Remove the adjustment tool. Put the gun cover back on and tighten the nuts. Reinstall the bubble dome.
Cleaning the Game Field
1.
3.
4. Turn off the game power so you are not accidentally shot. First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome. Use a vacuum cleaner with a brush attachment to remove the loose dirt and dust. Reinstall the bubble dome.
Cleaning the Electronic Components
Maintenance
- Unlock and open the door to the power supply and game PCB.
- Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet.
Cleaning the Bubble Dome
and Windows
Keep the bubble dome and windows clean so that the players can clearly see the prizes and the results of their shooting. Use window cleaner and soft paper towels on the dome and window to clean them. If you wipe the dome and windows with dry towels, you will scratch them.
Maintenance
Repairs
The following procedures include infrequent adjustments required by the game as well as removal, disassembly, reassembly, and replacement of game components. You probably will not need to do many of these procedures during the life of the game. The first procedures are those that have to do with the gun assembly, and the most likely repairs and adjustments to the gun are listed first. The next procedures concern replacing lights. The final procedures concern the feed screw motor, the firing ball delivery assembly, and removing the speaker and game PCB.
Unjamming the Gun Motor
If the gun motor is not working, first check to see if the game is plugged in and the power switch is on. Check that the service door next to the carousels is locked. If this door is not locked, the gun will not operate.
‘Tamperproot ‘Screw Plastic Feed Tube If the game is plugged in, the power is on, and the door is locked, the firing motor is probably jammed. The firing motor can jam when the power is turned off, balls are in the firing tube, and then the crank handle is turned. The balls jam between the pinch wheel and the firing wheel.
- Turn off the power to the game.
- Take off the bolt on the left side of the game using the 3/8-inch tamperproof wrench.
- Put the release tool (shown in Figure 4-5) into the cabinet through the screw hole. Insert it into slot in the end cap on the motor shaft which is inside the large round hole in the side of the gun. 4, Point the gun down. Turn the release tool clockwise. The jammed firing balls will fall out of the gun.
Firing Motor Release Tool
Figure 4-5 Unjamming the Motor
Maintenance
- Remove the tool. Put the screw back in the side of the game and tighten it.
Adding More Firing Balls
After you have lost at least 50 to 100 balls add more firing balls to the Pot Shot game. Replacement firing balls were shipped with your game in the storage compartment. If you have already used these, contact your distributor or Atari Customer Service, at the number listed on the inside front cover of this book, to get more firing balls. If you do not use Atari-supplied firing balls, but have another source, be sure that the balls are completely clean, and do not have any grease or dirt on them. if the balls are not clean, they will jam in the distributor and jam in the feed screw. You will probably have to replace the feed screw if you use dirty or greasy balls.
- Turn on the power to the game.
- Open rear door to the ball reservoir area. See Figure 4-1,
- Turn on the feed screw by opening the coin door and pressing down on the auxiliary coin switch enough times to give three games, then pressing the Start button quickly three times.
- As the screw turns, add 50 to 100 balls.
- To make sure that you haven’t added too many balls watch the ball distributor to see if the balls jams. If the balls do jam, remove some of the balls.
- After you are sure the balls are not jamming, put the door back on the ball reservoir area.
Replacing the Gun Ratchet Assembly Spring
If the crank handle does not make any noise when it is turned clockwise, and you have already tightened the ratchet wheel, the ratchet assembly spring is probably sprung and must be replaced.
- Turn off the game power.
- Take off the outside gun cover by removing the seven washers and screws on each side of the gun. Do not remove the two screws on the right side that hold the crank handle on the gun.
- Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome. 4, Inside the game, on the flat metal plate against the black rubber diaphragm, remove the two nuts below the chain bracket with a 3/8-inch nut driver.
- Pull off the outside gun cover carefully, using the gun handle.
- Inside the gun, opposite the crank handle, is the ratchet wheel and the ratchet assembly that strikes against the wheel. See Figure 6-2. The spring is in the ratchet assembly.
- Unhook the spring from around the screw at the end of the striker.
- Remove the ratchet assembly by unscrewing the two socket-head screws holding the assembly on the gun. Use a 5/32-inch Allen wrench.
- Take out the assembly and unhook the old spring from the floor of the gun. Put the hook of the new spring through these holes,
- Reinstall the ratchet assembly. Be sure the ratchet pin is centered on the ratchet wheel.
- Adjust the ratchet assembly so the pin stops the ratchet wheel from rotating backwards.
- Hook the new spring on the screw at the end of the striker,
- Push the gun cover back on. Push the four studs through the diaphragm and the metal plate. Put nuts on the top two studs. The bottom studs are used only as guides.
- Replace the seven screws and washers on each side of the outside gun cover.
- Reinstall the bubble dome.
Replacing the Gun Pinch
Wheel Cushion
The pinch wheel cushion will eventually wear and need to be replaced. 1, Turn off the game power.
- Take off the outside gun cover by removing the seven screws and washers on each side of the gun. Do not remove the two screws on the right side that hold the crank handle on the gun.
- Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome.
- Inside the game, on the flat metal plate against the rubber diaphragm, remove the two nuts below the chain bracket with a 3/8-inch nut driver.
- Carefully pull the outside gun cover off using the gun handle.
- Remove the two socket-head screws that hold the sprocket and pinch wheel assembly on the bottom of the gun. Use a 5/32-inch Allen wrench. See Figure 6-2,
- Pull the assembly to the front of the gun so you can work on it.
- Pull off the old pinch wheel cushion.
- Put on the new pinch wheel cushion. Make sure it is centered on the pinch wheel.
- Reinstall the sprocket and pinch wheel assembly.
- Push the outside gun cover back on. Push the four studs through the diaphragm and the flat metal plate. Put nuts on the top two studs. The bottom studs are used only as guides.
- Reinstall and tighten the 14 screws and washers on the outside gun cover.
- Adjust the firing tube as described in Adjusting the Firing Tube in the Preventive Maintenance section of this chapter.
Replacing the Gun Support
Chain
The chain holding the gun weight may need to be replaced. See Figure 6-1. The chain bar, screwed into the cabinet above the gun, holds the chain. The chain is Maintenance
attached to the gun by the chain bracket on the flat metal plate.
- Turn off the game power.
- First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome.
- Remove the nuts holding the chain bracket on the flat metal plate. Use a 3/8-inch wrench. (The diaphragm can support the weight of the gun temporarily.) 4, Remove one cotter pin from the chain bracket. Remove the rod. The bottom part of the chain is now free.
- Remove the bolts from the chain bar on the cabinet with a 7/16-inch nut driver or box open-end wrench, Take the chain off the bar.
- Put the new chain in place on the bracket on the metal plate. Slide the rod through the bracket and chain. Install a new cotter pin to hold the rod in place.
- Replace the screws holding the chain bracket on the flat metal plate. Use a 3/8-inch wrench.
- Install the new chain on the bar on the cabinet. Put the screws holding the chain bar back in and tighten them.
- Reinstall the bubble dome.
Replacing the Gun Diaphragm
If the black rubber diaphragm is worn or has holes in. it, it must be replaced.
- Turn off the game power,
- First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the bubble dome.
- Take off the small square metal cover in the lower corner of the cabinet interior. This cover protects the electical harness connections for the gun. Carefully pull out the wires until you can reach the connectors, Disconnect the connectors.
- Remove the four tamperproof screws from the gun movement restrictor panel on the front of the cabinet, See Figure 6-1.
- Turn the crank handle parallel to the bottom of the gun.
- Remove the 10 screws in the right and left diaphragm holders that press the black rubber diaphragm against the inside of the cabinet. Use a 7/16-inch socket to remove the screws.
- Remove the two screws that hold the chain bar on
Maintenance
the cabinet above the gun. Put a piece of wood between the gun and the bottom of the cabinet to support the weight of the gun. Do not let the gun drop.
- Pull the gun out of the cabinet towards the back of the game.
- Lay the gun on a work bench. Refer to Figure 6-2 for an exploded illustration of the gun. Remove the inside gun cover. Take off the four nuts facing the player side of the game with a 3/8-inch wrench. Pull the gun cover off enough to clear the studs. Then slide the gun cover to the left. Finally, pull the cover completely.
- Take off the outside gun cover by removing the seven screws and washers on each side of the gun. Do not remove the two screws on the right side that hold the crank handle on the gun.
- Use a 3/8-inch socket to remove the two nuts below the chain bracket on the flat metal plate. Pull off the outside gun cover.
- Remove the firing assembly bracket. The two nuts that hold the bracket are in the outside part of the gun. Use a 7/16-inch nut driver to remove the nuts,
- Remove the five nuts holding the diaphragm between the flat metal plate and welded gun case. Use a 7/16-inch socket. You do not need to remove the middle gun cover from the flat metal plate.
- Install the new diaphragm between the welded gun case and the flat metal plate. Tighten the five nuts with a 7/16-inch nut driver.
- Install the firing assembly bracket. Use a 7/16-inch nut driver to tighten the two nuts. Check the firing tube adjustment following the procedure in Adjusting the Firing Tube in this chapter.
- Reinstall the outside gun cover. Install the inside gun cover over the firing assembly.
- Be sure the crank handle is still parallel to the bottom of the gun. Put the gun back in the game.
- Suspend gun from the chain on the chain bar. Put the two screws into the chain bar and screw them into the cabinet.
- Put on the gun movement restrictor panel on the outside of the cabinet. Screw the four tamperproof screws into the cabinet.
- Reinstall the left and right diapharagm holders that press the black rubber diaphragm against the inside of the cabinet. Install the 10 screws.
- Reconnect the electrical connectors.
- Reinstall the bubble dome.
4-10
Replacing the Gun Firing
Tube
The firing tube may eventually wear. Do the following procedure to remove and replace it.
- Turn off the game power.
- First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome.
- Remove the inside gun cover. Take off the four nuts facing the player side of the game with a 3/8inch wrench. Pull the gun cover towards the back of the game enough to clear the studs. Then slide the gun cover to the left. Finally, pull off the cover towards the back of the game.
- Loosen the hose clamp and remove the plastic feed tube from the gun.
- Remove the nuts that hold the firing tube on the firing assembly bracket. See Figure 4-3. Remove the nut below the motor with a 3/8-inch box open-end wrench and the two above the motor with a 3/8-inch socket.
- Put in the new firing tube. Put on the nuts. Do not tighten the nuts.
- Do the procedure Adjusting the Firing Tube in the Preventive Maintenance section of this chapter.
- Do the procedure Adjusting the Firing Wheel in the Preventive Maintenance section of this chapter.
Motor
If the firing motor does not work anymore, do the following procedure to replace it.
- Shoot any firing balls that are in the plastic feed tube or in the gun.
- Turn off the power.
- Remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the bubble dome. 4, Remove the inside gun cover. Take off the four nuts facing the player side of the game with a 3/8inch wrench, Pull the gun cover towards the back of the game enough to clear the studs. Then slide the gun cover to the left. Finally, pull off the cover towards the back of the game.
- Loosen the hose clamp and remove the plastic feed tube from the gun.
- Loosen the socket-head screw holding the firing wheel on the motor with a 5/32-inch Allen wrench. See Figure 4-3. Take the firing wheel off the motor.
10.
11.
12.
13.
14,
15.
16.
17. Take the wires out of the tie wrap below the gun. Disconnect the motor electrical connectors. Remove the three nuts and washers that hold the motor on the firing assembly bracket. Loosen the three motor mount nuts with a 3/8-inch socket. These nuts are on either side of the motor. See Figure 4-3. Take the motor out of the game and remove the fan and the large slotted end cap on the motor shaft. Remove the two nuts on the motor clamp plate on the top of the motor with a 3/8-inch wrench. Then take off the two nuts that hold the motor in the motor mount. Use an 11/32-inch nut driver. Remove the motor. Put the new motor into the motor bracket. First, put the motor clamp plate back on the top of the bracket and tighten the nuts until the plate touches the motor, but does not clamp it. Put two nuts on the motor studs and tighten them with an 11/32-inch nut driver, so you pull the motor towards the front of the motor bracket.
When the motor is tight against the bracket, tighten the nuts on the top in the clamp plate. Put the fan and the large slotted end cap back on the motor shaft and tighten the set screws that hold them on. Put the motor assembly back on the firing assembly bracket. Pat on the three nuts that hold it on the bracket. Do not tighten the nuts. Put on a new tie wrap to hold the wires. Reconnect the motor wiring with the wiring harness. 18.
19. Maintenance
Put the firing wheel back on. Line up the firing wheel on the center of the firing tube. Check the centering of the firing wheel from the
20.
21.
22. end of the gun. You can hold a mirror in front of the sensor block on the gun to look at the reflection of the firing wheel through the hole in the sensor block, The most dangerous way to check the centering is to look down the firing tube through the hole in the sensor block at the end of the gun. You can be shot in the eye if the game power is on. If you do it this way, hold a clear acrylic panel between you and the gun. After you have centered the firing wheel, turn on the game power and watch the gun from above to see if the firing wheel is actually centered over the firing tube. If not, turn off the power and try again. Always check the centering with the motor running. When the firing wheel is centered, turn off the power, and tighten the set screw on the firing wheel, Finally, adjust the firing wheel height as described in Adjusting the Firing Wheel in the Preventive Maintenance section of this chapter.
Replacing the Gun Shot
Sensor
if no noise is produced when the gun fires, replace the shot sensor and emitter. 1.
2. Turn off the game power. First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome. Remove the inside gun cover. Take off the four nuts facing the player side of the game with a 3/8inch wrench. Pull the gun cover towards the back of the game enough to clear the studs. Then slide the gun cover to the left. Finally, pull off the cover towards the back of the game. The shot sensor and emitter are in the black box on the end of the gun. Both sensor and emitter have two wires attached to their holders. See Figure 4-3,
4-11
Maintenance
- Loosen the two lock nuts on the socket-head screws on either side of the cutout in the middle of the box. Use a 1/4-inch flat wrench.
- Loosen the socket head screws. Carefully remove the component holders and the components by gently pulling them out of their holes on the sides of the box. If the components won't come out of the holes, loosen the screws more.
- Replace the sensor and the emitter in the holders.
- Put the holders with the components back in the holes. Tighten the screws finger tight. If you overtighten the screws, you can crush the components.
- Tighten the two lock nuts with a 1/4-inch flat wrench.
- Put the gun cover on, tighten the nuts, and put the bubble dome back on.
Replacing the Start Switch
or Button
If you need to replace either of these, take off the instruction panel.
- Turn off the game power.
- Take off the top and bottom retainers on the instruction panel by removing the four screws in each retainer.
- Remove the retainers, holding the graphics and plastic shield on the game.
- Carefully lift off the plastic shield a little ways off the game. Pull out the start button light assembly. The start switch is on the bottom of this light.
- Take off the instruction panel. If you are replacing the start button, unscrew it from the panel.
- Assemble in reverse order.
Replacing Lights
If the game lights are burned out, replace them immediately. If the prizes are not properly lit, earnings may drop. Instruction Panel Lights
- Turn off the game power.
- Take off the top and bottom retainers of the instruction panel by removing the four screws in each retainer.
- Remove the retainers, holding the graphics and plastic shield on the game.
4-12
- Carefully lift off the plastic shield a little ways off the game. Pull out the start button light assembly.
- Take off the instruction panel.
- Remove the fluorescent light from the light fixture.
- To-remove the entire light fixture open the upper coin door and disconnect the light harness connector. The light harness is a flat white wire.
- Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
- Replace the fluorescent light and/or light fixture in the reverse order of removal.
Playfield Light
- Turn off the game power so you are not accidentally shot.
- Either take off the bubble dome or open a carousel access door and remove a carousel to gain access to the screws holding the acrylic sheet over the playfield light.
- Use a Phillips screwdriver to remove the five screws that hold the acrylic shield over the light. Lift off the shield. Remove the graphics. Remove the fluorescent light from the light fixture.
- To remove the entire light fixture, disconnect the light harness connector by the side of the light.
- Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
- Replace the fluorescent light and/or light fixture in the reverse order of removal.
“Hold Your Fire” Lights
Turn off the game power to avoid being shot.
- Either take off the bubble dome or open a carousel access door and remove a carousel to gain access to the screws holding the acrylic sheet over the light.
- Use a Phillips screwdriver to remove the five screws that hold the acrylic shield over the light. Remove the acrylic shield. Remove the light from the light fixture.
- To remove the entire light fixture, disconnect the wires from the light.
- Remove the four screws holding the light fixture. Remove the light fixture.
- Replace the light and/or light fixture in the reverse order of removal.
Lights Over Prizes
- Turn off the game power.
- Open the gear assembly area.
- Remove the fluorescent light from the light fixture. 4, To remove the entire light fixture, disconnect the light harness connector.
- Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
- Replace the fluorescent light and/or light fixture in the reverse order of removal.
Marquee Light 1, Tur the game power off.
- Use a Phillips screwdriver to remove the four screws in the retainer on the top of the cabinet that hold the attraction shield in place. Remove the retainer,
- Remove the attraction shield by pulling it up and out. 4, Remove the fluorescent light from the light fixture.
- To remove the entire light fixture, open the gear assembly access door. Disconnect the light harness connector in the gear assembly area.
- Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
- Replace the fluorescent light and/or light fixture in the reverse order of removal.
- Put the attraction shield back. 9, Put the retainer back on and tighten the four screws,
Replacing the Feed Screw
Replacing the Feed Screw Pulley Belt
If the feed screw pulley belt is worn and slips, replace it following this procedure.
2. 3. Turn off the game power. Open the ball reservoir area. Loosen the screws that hold the motor on the floor of the game. See Figure 4-1. Maintenance
Take off the old belt. Put on the new belt and adjust it: move the motor back and forth until the belt has about 1/2 inch of slack when you push or pull on it.
Motor
If the feed screw motor does not work, replace it following this procedure. i.
3. Turn off the game power. Open the ball reservoir area. The motor is held to the floor of the game by two screws, See Figure 4-1. Remove these screws. Take off the belt. Check the belt for wear. If it is worn, replace it, following the procedure in Replacing the Feed Screw Moior Belt. Install a new motor. Put the belt on the motor pulley. Tighten the screws enough to hold the motor in place. Adjust the belt tension by moving the motor back and forth. The belt should have about 1/2 inch of slack when you push or pull on it. Tighten the screws when the belt has the proper amount of slack.
Replacing the Firing Ball Delivery Sensors
If the firing balls are not counted correctly every game, and you have checked the settings on the DIP switches on the Game PCB to be sure the number of firing balls allotted every game is correct, you may need to replace the sensors.
Turn off the game power. First remove the bubble dome by removing all the tamperproof screws holding the dome on the game. Lift off the dome. The ball delivery sensor and emitter are in the black block between the plastic feed tube and the feed screw. See Figure 4-2. Loosen the two lock nuts on the socket-head screws on the top of the block with a 1/4-inch wrench.
4.13
Maintenance
Loosen the socket head screws. Carefully remove the component holders and the components by gently pulling them out of their holes on the sides of the block. If the components won't come out of the holes, loosen the screws more. Replace the sensor and the emitter in the holders. Put the holders with the components back in the holes. Tighten the screws finger tight. If you overtighten the screws, you can crush the components. Tighten the two lock nuts. Put the bubble dome back on.
Removing the Game PCB
Perform the following procedure to remove or replace the Game PCB. See Figure 3-1 for the location of the game PCB. 1, Turn the game power off.
- Unlock and remove the rear door to the the power supply and PCB area.
- Disconnect the harness connectors from the Game PCB.
- Use a Phillips screwdriver to remove the screw and washer holding the Game PCB to the cabinet.
- Grasp the edge of the Game PCB and gently slide it to the right and up.
- Replace the Game PCB in the reverse order of removal.
Removing the Speaker
Perform the following procedure to remove or replace the speaker. 1. 2. Turn the game power off. Remove the four tamperproof screws holding the speaker grille to the cabinet. Remove the grille.
Use a Phillips screwdriver to remove the four screws holding the speaker to the cabinet. Do not let the speaker fall. Remove the speaker just far enough to disconnect the two speaker wires. When you reassemble the speaker and the wires, be sure that you hook up the wires correctly. The signal wire for the speaker should be attached to the speaker tab marked with color, a + sign, or a round dot. (The signal wires are shown on the game wiring diagram; refer to the schematic included in the manual.) Replace the speaker in the reverse order of removal.
4-14 Z
wy
AY
Chapter 5
Troubleshooting
The information in this chapter discusses troubleshooting aids and techniques to assist you when you have trouble with your game. Most problems can be located by using the information in this chapter. However, if problems persist, contact your local distributor or the Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.
Troubleshooting
5-2
Mechanical Troubleshooting
‘You should perform the preventive maintenance procedures in Chapter 4 on a regular basis to avoid some of the problems listed below. If you have problems, try the first suggestion in the series. If that does not work, try the next suggestion. After you have tried all the suggestions that apply to your problem, call your distributor or Atari Customer Service if you still have not solved your problem. Firing Ball Problems Firing balls are not loading, no music is playing, and no lights are on. 1, Check that the game is plugged in.
- Check that the game power is on.
- Check if any fuses are blown on the power supply. Firing balls are not loading, but the music is playing, and the feed screw is turning. 1, The balls are probably jammed in the ball distributor. You have too many firing balls in the game. Open the door to the ball reservoir area and take out about 30 balls. If this does not cure the problem, take out more balls.
- If there are no balls in the reservoir, the balls are probably jammed on the return surface. They will jam there if the game is not level. Level the game following the procedure Levelling the Game in Chapter 1. Firing balls are not loading and the gun doesn’t work, but the lights are on and the carousels are turning. The carousel access doors are probably unlocked. The feed screw and gun will not work if the doors are unlocked. Firing balls do not roll smoothly through the plastic feed tube.
- Check for kinks and twists in the feed tube.
- Replace the feed tube if it is extremely dirty. Balls do not fire.
- Check the carousel service doors. They must be locked before the gun can fire.
- If the power to the game has been off, try unjamming the motor. The directions for this procedure are in Chapter 4 in Unjamming the Motor. If this is a problem that has recently gotten worse, try the following: a. Check the O-ring in the gun firing assembly and see if it is worn. Replace it if it is. The directions for this procedure are in Chapter 4 in Replacing the Gun O-Ring. b. Adjust the firing wheel. The directions for this procedure are in Chapter 4 in Adjusting the Firing Wheel. c. If you have taken out the firing motor, you may not have adjusted the firing wheel correctly when you put it back in, Follow the procedure Replacing the Firing Motor in Chapter 4. The balls fire, but they are not fired with enough force to knock out prizes.
- Check to see if the O-ring in the gun firing assembly is worn. Replace it if necessary, following the procedure in Replacing the Gun O-Ring in Chapter 4.
- Adjust the firing wheel. The directions for this procedure are in Adjusting the Firing Wheel in Chapter 4.
- If you have tried steps 1 and 2, and the game has been operating for a number of months, you might need a new firing tube. The directions for replacing the firing tube are in Chapter 4, Replacing the Firing Tube. 4, If you have taken out the firing motor, you may not have adjusted the firing wheel correctly when you put it back in. Follow the procedure Replacing the Firing Motor in Chapter 4. Balls do not always fire, or too many fire, when the crank handle is turned.
- Check the firing tube adjustment. Follow the procedure in Adjusting the Firing Tube in Chapter 4.
- Check the pinch wheel cushion for wear. If it is worn, replace it. Follow the procedure in Replacing the Pinch Wheel Cushion in Chapter 4.
- If you have replaced the pinch wheel cushion and still have this problem, be sure that the pinch wheel is centered over the firing tube. Firing balls occasionally drop out of the gun on the player side. This is normal for the game. Put the firing balls back in the game by dropping them inside the prize door. Firing balls are not going into the plastic feed tube. In normal operation, some of the balls will fall out of the ball receiver assembly while the plastic feed tube is filling. The firing ball delivery sensor
counts the number of balls that actually go into the plastic feed tube, so every player receives the number of balls selected on the DIP switches on the game PCB. Too many balls are delivered by the feed screw and the feed tube is already full.
- If this happens occasionally, the player has probably put in more coins than needed for one game and then pushed the Start button more than once quickly.
- If this happens in every game, check the DIP switches at 4E on the game PCB. You have probably chosen more than 90 balls to be delivered each game. Instructions for changing the DIP switches are in Switch Options in Chapter 3.
- If the DIP switches at 4E on the game PCB are set to 90 balls or less, and this always happens, replace the ball delivery sensors. Follow the procedure in Replacing the Ball Delivery Sensors in Chapter 4. The feed screw delivers balls very slowly.
- Take the slack out of the feed screw motor belt. Follow the procedure in Checking the Feed Screw Motor Belt in Chapter 4.
- If the belt is worn, replace it. Follow the procedure in Replacing the Feed Screw Motor Belt in Chapter 4. The feed screw delivers too few balls. 1, If this happens occasionally, check the ball distributor and see if the balls are jammed. The game will jam if it has too many firing balls. Open the door to the ball reservoir area and take out about 30 balls. If the balls continue to jam, take out more balls.
- If this happens occasionally, check the ball distributor and see if the balls are returning to the distributor. If there are only a few balls in the reservoir and distributor, the balls may be jammed on the return surface. This happens when the game is not level. Level the game, following the directions in Chapter 1 in Levelling the Game.
- If this happens in every game, check the DIP switches at 4E on the game PCB to see how many balls are to be delivered each game. You may have chosen too few firing balls to be delivered each game. Instructions for changing the DIP switches are in Chapter 3 in Switch Options. 4, If this happens in every game, check the feed screw motor belt. Follow the procedure in Checking the Feed Screw Motor Belt in Chapter 4. Troubleshooting
Gun Crank Problems Crank handle does not make noise. Refer to Sound Problems, below. When the crank handle is turned, balls do not fire or too many fire. Refer to Firing Ball Problems, above. Prize Ball Problems Prize balls do not roll to the prize door. Make sure your game is level. If the back of the game is lower than the front, the balls will not roll to the prize door. Level the game according to the directions in Levelling the Game in Chapter 1. Carousel Problems Upper platform discs on the carousel are not turning or turning slower than the lower platform discs. The top spacer was not pressed down hard enough when the screw was tightened. Take the carousel out, loosen the screw in the top spacer, press down on the top spacer, and tighten the screw.
Sound Probiems When the crank handle turns, it makes little or no noise.
- Adjust the ratchet wheel. Follow the procedure in Checking the Crank Handle in Chapter 4.
- Adjust the ratchet assembly. The assembly may have gotten loose and slid back from the ratchet wheel, Follow the procedure in Replacing the Ratchet Assembly Screw in Chapter 4, but only adjust the assembly, do not replace the spring.
- Replace the ratchet assembly spring. The spring is probably sprung (stretched out). Follow the procedure in Replacing the Ratchet Assembly Screw in Chapter 4. No shot sound is produced when balls are fired. Replace the gun shot sensors. No game sounds at all.
- Check the speakers and the wiring. 2, Check the +12 Volt supply from the power supply board.
5-3
‘Troubleshooting
Electronic Troubleshooting
Check Fuses Check for open fuses. Refer to the power supply parts list in Chapter 6 for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating. Check Power-Supply Voltages If no circuits are operating correctly, you probably have a power supply problem. Be sure that the proper line voltage is available to the game. Refer to the label on the back of the game for its voltage rating.
5-4 Check the LED on the Game PCB to make sure the +5 V supply is good. Visual Check Check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged components. Check Individual Components Check soldered-in passive components (e.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, the most practical way to determine if a component is faulty is to substitute a new component. Before you do this, make sure that you do not have some other circuit problem that could damage the new component.
“and Schematics
\ This chapter provides Yeformation you need to
order parts for your game,
The PCB parts lists are arkanged in alphabeticat””
order by component. Each’ component section is
arranged alphanumerically by reference designator. a Other - parts lists are arrangé géd/alphanumerically by. Atari part number.-Ti.-thiese parts lists, all A- _-Previx numbers, sotie first, Next come part num-
arranged alphanumerically by reference designa by. Atari part number.-Ti.-thiese parts lists, all A bers with a. tw6 number designation followed by a
hyphen (09- through 99-). Ending the list are part
os numbers with six numbers followed by a hyphen we _GQVEI- through 201000-). Oo oe When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. i? Atari Customer Service phone numbers are listed \ on the inside front cover of this manual.
Illustrated Parts Lists Pot Shot
A045202-01 7 “Hold Your Fire" bpp Ught Assy 171086-001
| 170001-001 | 045247-01 | Fluorescent | 048248-01 |
| Incandescent | Glass Panel | Lamp Fixture | Retainer |
| 045245-01 | Lamp | A045208-01 |
Acrylic Panel Marquee Assy
| 045232-01 | 045235-01 | 045224-02 | ||
| ‘Hold Your | = | -uae408.07 | Graphics | Right Decal |
Fire” Decal Assy 045403-01 72-5544 ‘A045205-01 or Carousel 2.3/4-Inch
| ‘A045205-02 | . | 3 |
Skylight Assy Screw
A045431-01 a 045223-02 Feed Screw . Rear Fight
| ° | fop | De |
045229.01 Front Play Assy Field Decal 045219-01 045240-01 $
| Front Playfield | Ps | % | 045225-02 / |
Acrylic Panel Right Carousel 045226-01 Door Decal Prize Door aiasoe0-03
| Decal | . | 4 | Right Carousel |
: Door
148004-003 oasari-oy SPeeker Grille 045246-01 Acrylic Side Window
045221-01 Rear Right 045270-01 / Upper S ‘Narrow Decal Retainer 045241-01 Lit Playfield 176037-4008 J Acrylic Panel #10 Tamperproot / Screw 045230-01 Lit Playfield Decal L__ 045231-01 Vertical Decal
045220-02
| Ze | K | < | “ST | Front Right |
| A045203-01 | , | ~ Narrow Decal |
Instruction Panel . Assy 045228-01 Instruction Decal
cs Shield Acrylic Shi t7e020-212 o45269-01 A°Y | Square Drive Lower —TS il 045222-02 Screw Retainer . Front Right 178233-001 Start Button With Lamp Assy 160044-001 Switch 178048-002 A045383-01 Rigid Caster Ten sip tacit 178023-002 ey i Swivel Caster 94537201 Cash Box Gun Movement 045254-01 Restrictor Panel
| 171027-001 | Coaster | —aagystie-01 |
| Coin Door | 78-3201 | Component |
Leveller Bracket Assy (4places) Figure 6-1 Cabinet-Mounted Assemblies A045200-01 A
6-2
Pot Shot Illustrated Parts Lists
Items Not Shown:
045225-01 Left Carousel Door Decal 045223-01 Rear Left ‘A045128-01 Top Decal Carousel Motor 045222-01 Assy Front Left Top Decal 045221-01 beta aoa Fluorescent Narrow Decal Light pissing (2 places) Front Left 171086-002
| Narrow Decal | tener | Fluorescent | |||
| 178126-002 | 045429.01 | Feed Tube | paseaa-oy | \ Lamp Fixture | |
| #10 Tamperproot | Plastic Feed | Bracket | Aeea mane | Acrylic Ceiling) | (2 places) |
Tube anel 99-11006. Release Tool 045971-02 lease oo! (2 places) _\ Retaining Clip Right Diaphragm Holder 045370-01 ‘Top Door
A045250-01 Left Carousel Door
045491-01 Chain Bar
045413-01 Mounting Plate A045410-01 ‘Carousel Gear Assy 045971-01 Left Diaphragm Holder
A036189-01 Interlock Switch A045402-01 Assy Carousel Assy
A045125-01 ‘On/Off Switch with Harness
045441-01 178126-003 Ball Distributor 3/8 Tamperproot Wrench A045211-01 Anti-Tilt Mechanism ‘A045129-01 Feed Screw Motor Assy
045440-01 045404-02 i Feed Screw 1/4-Inch-High T, Pulley Spacer 178220-001
| 045404-03 | 045367-01 | Pulley Bett |
4/8-Inch-High Storage Door Spacer 045405-01 3.1/2-Inch-High Spacer oagane-si 170003-001 End Spacer rom A045120-01 045368-01 Rear Door oassoe-ta 171086-001 Powe’ Suey Ball-Holding Assy ok Fluorescent
| Lamp Fixture | A045052-01 | 045445-01 |
| 045408-01 | Pot Shot PCB | Feed Screw |
| Platform Disc | "Assy | Motor Pulley |
045404-01 045444." ailnch-High food Screw Spacer Motor Bracket 045492-01 Gun Adjustment Too!
Figure 6-1 Cabinet-Mounted Assemblies, Continued
6-3
Illustrated Parts Lists Pot Shot
Cabinet-Mounted Assemblies Parts List
Part Description
A036189-01 Interlock Switch Assembly A045052-01 Pot Shot PCB Assembly A045112-01 Main Assembly Harness A045113-01 Upper Light Assembly Hamess A045114-01 Lower Light Assembly Harness A045118-01 Component Bracket Assembly A045120-01 Power Supply Assembly A045125-01 Power On/Off Switch with Harness Assembly A045129-01 Feed Screw Motor Assembly A045201-01 Cabinet With Pallet Assembly A045202-01 Flashing Light “Hold Your Fire” Assembly. Replaceable Parts: 179239-001 Rear-Terminating Lamp Receptacle A045203-01 Instruction Panel Assembly. Replaceable Parts: 045234-01 Coinage Label 045228-01 Instruction Decal 045239-01 Acrylic Shield for Instruction Decal 160044-001 Snap-Action Switch 178233-001 Square Green Start Button With 6.3 Volts Lamp Assembly A045204-01 Lit Playfield Assembly. Replaceable Parts: 170003-001 18-Inch 15-Watt Fluorescent Light 171086-001 18-Inch Fluorescent Lamp Fixture 176015-i10 Tapping Pan Hd. Cross-Recessed #10 x 5/8-Inch Lg. Screw 99-11006 Fluorescent Lamp Retaining Clip A045205-01 skylight Assembly A045206-01 Carousel Components Kit: 045404-03 1/8-Inch-High Spacer 045404-04 1/16-Inch-High Spacer 045409-01 Ball-Holding Disc With 2 7/8-Inch Diameter Holes 73-00624 3/32 x 1 1/2-Inch Steel Cotter Pin A045207-01 Steel Firing Ball Kit (50 Balls) A045207-02 Spare Firing Ball Kit (100 Balls) A045208-01 Marquee Assembly. Replaceable Parts: 045224-01 Left Marquee Decal 045224-02 Right Marquee Decal 045235-01 Marquee Graphics 045247-01 Glass Panel 045248-01 Retainer 170003-002 24-Inch 20-Watt Fluorescent Light 171086-002 24-Inch Fluorescent Lamp Fixture 99-11006 Fluorescent Lamp Retaining Clip A045211-01 Anti-Tit Mechanism A045250-01 Left Carousel Access Door A045250-02 Right Carousel Access Door A045378-01 Bottom Step Assembly (Shipped assembled with the Top Step Assembly, Part No. A045383-01) A045383-01 Top Step Assembly (Shipped assembled with the Bottom Step Assembly, Part No. A045378-01)
Illustrated Parts Lists
Cabinet-Mounted Assemblies Parts List, Continued
Part No. Description
A045402-01 Carousel Assembly. Replaceable Parts: 045403-01 Carousel Shaft 045404-01 3/4-Inch-High Spacer 045404-02 1/4-Inch-High Spacer 045404-03 1/8-Inch-High Spacer 045405-01 3 1/2-Inch-High Standard Spacer 045406-01 End Spacer 045408-01 Platform Disc 045409-02 Ball-Holding Disc with 3 3/8-Inch Diameter Holes 72-5112 #10-24 x 3/4-Inch Hex Head Machine Screw
A045410-01 Carousel Gear Assembly. Replaceable Parts: A045128-01 Carousel Motor Assembly 045413-01 Mounting Plate 177010-241 Polymer Hex Lock Nut 73-00612 3/32 x 3/4-Inch Steel Cotter Pin 73-00624 3/32 x 1 1/2-Inch Steel Cotter Pin 75-910d #10-32 Hex Nut A045431-01 Feed Screw Assembly A045450-01 Gun Assembly (See Figure 6-2) A045498-01 Ball Receiver Assembly 045219-01 Feed Screw Decal (Included with Feed Screw Assembly, Part No. A045431-01) 045220-01 Front Left Narrow Decal 045220-02 Front Right Narrow Decal 045221-01 Rear Left Narrow Decal 045221-01 Rear Right Narrow Decal 045222-01 Front Left Top Decal 045222-02 Front Right Top Decal 045223-01 Rear Left Top Decal 045223-02 Rear Right Top Decal 045225-01 Left Carousel Door Decal 045225-02 Left Carousel Door Decal 045226-01 Prize Door Decal 045229-01 Front Playfield Decal 045230-01 Lit Playfield Decal 045231-01 Decal on Vertical Panel in front of Lit Playfield 045232-01 “Hold Your Fire” Decal 045233-01 Upper Redemption Decal 045233-02 Redemption Decal 045240-01 Front Playfield Acrylic Panel 045241-01 Lit Playfield Acrylic Panel 045244-01 Ceiling Light Acrylic Panel 045245-01 “Hold Your Fire” Acrylic Panel 045246-01 Acrylic Side Window 045247-01 Glass Marquee Panel 045253-01 Redemption Decal Overlay
Illustrated Parts Lists
Cabinet-Mounted Assemblies Parts List, Continued
Part No. Description
045254-02 Leveller Coaster 045258-01 High Voltage Cover 045269-01 Lower Retainer for Instruction Panel 045270-01 Upper Retainer for Instruction Panel 045271-01 Speaker Grille 045367-01 Storage Compartment Door 045368-01 Rear Door 045370-01 Top Door 045371-01 Left Gun Diaphragm Holder 045371-02 Right Gun Diaphragm Holder 045372-01 Gun Movement Restrictor Panel 045429-01 Plastic Feed Tube 045440-01 Feed Screw Pulley 045441-01 Ball Distributor 04544401 Feed Screw Motor Bracket 045445-01 Feed Screw Motor Pulley 045491-01 Chain Bar 045492-01 Gun Adjustment Tool 045496-01 Firing Motor Release Tool 045497-01 Plastic Feed Tube Bracket 129002-505 Capacitor, 5pF, 370 VAC 148004-003 5-Inch-Round, 5-Watt 8-Ohm Unshielded Speaker 170001-001 Incandescent Tubular 25W Clear Lamp (for “Hold Your Fire” Light Assembly) 170003-002 24-Inch 20-Watt Fluorescent Light (above Carousels and behind Instruction Panel) 171027-001 Over/Under 25¢/25¢ Coin Door 171086-002 24-Inch Fluorescent Lamp Fixture (above Carousels and behind Instruction Panel) 176037-4008 #10 Button Head Tamperproof Screw 176037-4832 3/8 Bution Head Tamperproof Screw 178023-002 3-Inch x 1 1/4-Inch Hard Wheel Swivel Caster 178048-002 4-Inch x 1 1/2-Inch Rigid Wheel Caster 178126-002 #10 Tamperproof Wrench 178126-003 3/8 Tamperproof Wrench 178220-001 Feed Screw Pulley Belt 72-5544 1/4 x 2 3/4-Inch Screw 73-00624 3/32 x 1 1/2-Inch Steel Cotter Pin 78-3201 Leveller 99-11006 Fluorescent Lamp Retaining Clip (above Carousels and behind Instruction Panel) 038091-01 Cash Box These items are the technical information supplements to the game: ST-318 Pot Shot Troubleshooting Label ™-318 Pot Shot Operators Manual
Illustrated Parts Lists
Mlustrated Parts Lists Pot Shot
045461-01 Top Shield 82-8006 Button Head Screw
‘75-010F Black Washer
‘A045483-01 inside Gun Cover Assy # A045483-02 178223-002 eae, O-ring saniied / &£ (# 178223-001) Gun Shield ‘ Co \ 048474-01 % | : . Firing Wheel (# 045474-02)
Firing Tube si Motor Clamp lot
75-0188 OO —_ Firing Tube 177010-238 p #8-32 Lock Nut g 045473-01 . Firing Tube Plate (A045127-01 Motor Assy 75-4003 131050-001 Pring Amy Set Screw Emitter 945476-01 Support Bracket Sensor Box
045492-01 > 177010-244 Gun Adjustment Nut Tool 178177-002 045486-0 Fan 045480-01 Motor End Cap Firing Motor x) Support “ Sea gar no™ EE 2 ‘A045479-01 Firing Motor Assy
Figure 6-2 Pot Shot Gun Assembly A045450-01 C
6-8
Pot Shot Illustrated Parts Lists
178200-005 Chain 75-010S 045464-01 vrmi0-241 Chain Bracket RatWiester 72-8008 Socket Head 045465-01 Middle Gun “ cole 044390-01 Pinch Wheel A045466-01 Cushion Feed Sprocket 72-8008 177010-241 pos ole Lock Nut seen 75-010S ae A045458-01 7eios Ratchet 75-0408 Spli-Lock Washer
Ratchet Pin
73-00612 arroniou Cotter Pin Lock Nut 045451-01 < Welded Gun Case 045463-01 Flat Metal Plate
s 78224-002
- Rotating 045501-01 / eQ) Handle Gun Diaphragm A045455-01 Crank Handle 177010-244 Assy Nut
82-8006 Socket-Head 176008-112 Screw Nylok Screw
045454-01 Raichet Wheel
178026-012 Spring
A045488-01 Outside Gun Cover Assy
Gun Handle
Figure 6-2 Pot Shot Gun Assembly, Continued
Illustrated Parts Lists
Pot Shot Gun Assembly Parts List
Part No. Description
A045455-01 Crank Handle Assembly 178224-002 Rotating Handle on Crank Assembly (sold separately from part no, A045455-01, Crank Handle Assembly) A045458-01 Ratchet Assembly. Replaceable Parts: 82-8010 #10-32 x 5/8-Inch Socket-Head Screw 178026-012 Spring A045466-01 Feed Sprocket Assembly. Replaceable Parts: 044390-01 Pinch Wheel Cushion 72-8008 #10-32 x 1/2-Inch Socket Head Screw 75-010 Flat #10 Washer 75-040 Split-Lock #10 Washer A045471-01 Firing Assembly (# Ireland-built cabinets use part no. A045471-02 ). Replaceable Parts: 045472-01 Support Bracket 045473-01 Firing Tube Plate 045474-01 Firing Wheel (# Ireland-built cabinets use part no. 045475-01) 045476-01 Sensor Box 045486-01 Slotted Motor End Cap 131050-001 Emitter 133038-001 Sensor 176008-108 #10-32 x 1/2-Inch Socket-Head Polymer Lock Screw 177010-241 #10-32 Polymer Hex-Head Lock Nut 178065-100 Tie Wrap 178177-002 Fan 178223-002 O-Ring (# Ireland-built cabinets use part no. 178223-001) 72-8409 #4-40 x 9/16-Inch Socket-Head Screw 75-4003 #10-32 x 3/16-Inch Hex-Head Cup Set Screw 75-914D #4-40 Hex Head Nut A045479-01 Firing Motor Assembly. Replaceable Parts: A045127-01 Motor Assembly 045480-01 Firing Motor Support 045481-01 Motor Clamp 177010-238 #8-32 Polymer Hex Head Lock Nut 177010-241 #10-32 Polymer Hex Head Lock Nut 75-0188 Flat #8 Washer A045483-01 Inside Gun Cover Assembly (# Ireland-built cabinets use part no. A045483-02). Replaceable Parts: 045487-01 Inside Vertical Gun Shield A045488-01 Outside Gun Cover Assembly 045451-01 Welded Gun Case 045454-01 Ratchet Wheel 045461-01 ABS Top Shield on Inside Gun Cover
045501-01 Gun Diaphragm 045463-01 Flat Metal Plate 045464-01 Chain Bracket 045465-01 Middle Gun Cover
6-10
Pot Shot Illustrated Parts Lists
Pot Shot Gun Assembly Parts List, Continued
Part No. Description
045492-01 Gun Adjustment Tool 176008-112 #10-32 Nylok Socket-Head Screw 177010-241 #10-32 Lock Nut 177010-244 #1/4-20 Lock Nut 178200-005 Endless Chain 72-8008 #10-32 Socket-Head Screw 73-00612 3/32 x 3/4-Inch Steel Cotter Pin 75-010F #10 Black Oxide Washer
75-0108 #10 Washer 75-0408 #10 Split-Lock Washer 82-8006 #10-32 Button-Head Screw
6-11
Illustrated Parts Lists
A045121-01 +5v Hames Assy
179211-001 Jumper
A045122-07 043396-01 116024-500 Power Tray Hamess Assy Power Supply Base 5w 50 Ohm Resistor
ini
A042384-01 N Line Filter Assy . .
034544-01 Fuse Block Cover 149007-001 17925-2205 Astec Switching Power Supply 5 Pos. Fuse Block
46-2015002 5 Amp 250 V Fuse 46-2013002 9 Amp 250 V Fuse 46-2011502 1.5 Amp 250 V Fuse
46-2011002 1 Amp 250 V Fuse
Figure 6-3 Power Supply Assembly A045120-01 A
6-12
Illustrated Parts Lists
Power Supply Assembly Parts List
Part No. Description
A042384-01 Line Filter Assembly A045121-01 +5V Harness Assembly A045122-01 Power Tray Harness Assembly 034544-01 Fuse Block Cover 043396-01 Power Supply Chassis Base 116024-500 5W 50-Ohm Chassis Mount Resistor 149007-001 5V/12V 5-Amp Astec Switching Power Supply Sub-Assembly (see parts list below) 178181-6808 Aluminum Stand-Off 179211-001 Terminal Block Jumper 179225-2205 5 Position Fuse Block 179231-002 2 Position Terminal Block 46-2011002 1 Amp 250 V Slow-Blow Fuse
46-2011502 1.5 Amp 250 V Slow-Blow Fuse 46-2013002 3 Amp 250 V Slow-Blow Fuse 46-2015002 5 Amp 250 V Slow-Blow Fuse
Astec 5-Volt Power Supply Sub-Assembly Model SA40-1304 Parts List
| Designator | Description | Part No. |
Capacitors
| C1, C2 | Capacitor, Met Poly, .1 pF, 20%, 250 VAC | 99-209076 |
| 3, C4 | Capacitor, Poly, 2200 pF, +20%, 250 VAC | 99-209077 |
| Cc | Capacitor, Met Poly, 2200 pF, +20%, 250 V | 99-209080 |
| c8 | Capacitor, Electrolytic, 220 pF, +100 -+10%, 10 V | 99-209072 |
| co | Capacitor, Ceramic, 1000 pF, +20%, 3 KV, Z5P | 99-209068 |
| cio | Capacitor, Met Poly, .022 pF, +20%, 250 VAC | 99-209079 |
| ci | Capacitor, Poly, .22 pF, +10%, 100 V | 99-209014 |
| c12z | Capacitor, Electrolytic, 2200 WF, +20%, 16 V, Sxa | 99-209073 |
| C13 | Capacitor, Poly, .01 pF, +5%, 50 V | 99-209075 |
| c14 | Capacitor, Electrolytic, 100 pF, +20%, 25 V, Sxa | 99-209006 |
| cs | Capacitor, Electrolytic, 1000 pF, +20%, 16 V, Sxa | 99-209008 |
| C16 | Capacitor, Poly, .022 pF, +20%, 50 V | 99-209078 |
| C17 | Capacitor, Electrolytic, 1000 pF, 20%, 10 V, Sm | 99-209071 |
| C18 | Capacitor, Ceramic, 330 pF, +20%, 100 V, SI | 99-209069 |
| C19 | Capacitor, Electrolytic, 470 pF, 20%, 16 V, Sm. | 99-209074 |
| C20 | Capacitor, Electrolytic, 100 pF, +20%, 16 V, Sm. | 99-209070 |
| c21 | Capacitor, Poly, .22 pF, +10%, 100 V | 99-209014 |
| C23, | Capacitor, Ceramic, .01 pF, +80-20%, 100 V, Z5U | 99-209003 |
Diodes
| D1 | Diode, RGP10A | 99-209083, |
| D2 | Diode, RGP10} | 99-209033 |
| D3. | Diode, GP10A | 99-209084 |
| D4, DS | Diode, RGP10} | 99-209033 |
6-13
Illustrated Parts Lists Pot Shot
Astec 5-Volt Power Supply Sub-Assembly Model SA40-1304 Parts List, Continued
Designator —_ Description Part No.
| D6, D7 | Diode, 1N4606 | 99-209030 |
| Ds | Assembly, Regulator/SCR/Diode/Heat Sink | 99-209105 |
| Ds | Diode, 12CTQ035 | 99-209107 |
| D9 | Diode, RGP10B | 99-209034 |
| D10 | Assembly, Diode/Heat Sink | 99-209103 |
| D1 | Diode, 1N4606 | 99-209030 |
| D12, D3. | Diode, 1N4001 | 99-209035 |
| DB1 | Diode, Bridge, KBPO8 | 99-209085 |
Inductors
| 1B | Inductor, 2.2 pH | 99-209029 |
| 14 | Inductor, 1.5 mH | 99-209028 |
| bb | Assembly, Inductor Coil | 99-209059 |
| 16 | Inductor, 4.4 pH | 99-209102 |
Transistors
| Ql | Transistor, NPN, 2SC2120 | 99-209082 |
| Q2 | Assembly, Transistor/Heat Sink | 99-209104 |
| 3 | Transistor, PNP, 2SB561 | 99-209022 |
Resistors
| R1 | Resistor, Carbon Film, 470K Ohm, +5%, 1/2 W | 99-209089 | |
| R2 | Resistor, Wirewound, 33 Ohm, +5%, 3 W | 99-209097 | |
| R3, R4 | Resistor, Metal Oxide Film, 100K Ohm, +5%, 1 W | 99-209054 | |
| RS | Resistor, Carbon Film, 1K Ohm, +5%, 1/4 W | 99-209086 | |
| RO | Resistor, Metal Oxide Film, 120 Ohm, +5%, 2 W | 99-209095 | |
| R7 | Resistor, Metal Film, 1 Ohm, +5%, 1 W | 99-209025 | |
| R8 | Resistor, Carbon Film, 27 Ohm, +5%, 1/4 W | 99-209040 | |
| RO | Resistor, Carbon Film, 68 Ohm, +5%, 1/4 W | 99-209090 | |
| R10 | Resistor, Carbon Film, 10 Ohm, +5%, 1/4 W | 99-209037 | |
| Ri | Resistor, Carbon Film, 15 Ohm, +5%, 1/4 W | 99-209087 | |
| R12 | Resistor, Metal Film, .75 Ohm, +5%, 1 W | 99-209091 | |
| R13. | Resistor, Carbon Film, 5.6 Ohm, +5%, 1/4 W | 99-209046 | |
| R14 | Resistor, Carbon Film, 47 Ohm, +5%, 1/4 W | 99-209043 | |
| R15, R16 | Resistor, Carbon Film, 270 Ohm, +5%, 1/2 W | 99-209041 | |
| R17 | Resistor, Carbon Film, 8.2 Ohm, +5%, 1/4 W | 99-209049 | |
| R1s | Resistor, Carbon Film, 330 Ohm, +5%, 1/4 W | 99-209042 | |
| RI9 | Resistor, Carbon Film, 56 Ohm, +5%, 1/4 W | 99-209045 | |
| R20 | Resistor, Carbon Film, 68 Ohm, +5%, 1/4 W | 99-209090 | |
| R21 | Resistor, Carbon Film, 330 Ohm, +5%, 1/4 W | 99-209042 | |
| R22 | Resistor, Carbon Film, 470 Ohm, +5%, 1/4 W | 99-209044 | . |
| R23 | Resistor, Metal Film, 8.2K Ohm, +1%, 1/4 W | 99-209094 | |
| R24 | Resistor, Metal Film, 2.7K Ohm, +1%, 1/4 W | 99-209093 | . |
| R25 | Resistor, Metal Film, 18K Ohm, +1%, 1/4 W | 99-209092 | |
| R27 | Resistor, Carbon Film, 22 Ohm, +5%, 1/4 W | 99-209088 | |
| R28 | Resistor, Carbon Film, 10 Ohm, +5%, 1/4 W | 99-209037 | |
| R29 | Resistor, Metal Oxide Film, 120 Ohm, +5%, 2 W | 99-209095 | |
| R30 | Resistor, Wirewound, 15 Ohm, +5%, 5 W | 99-209096 | |
| R32 | Resistor, Carbon Film, 10 Ohm, +5%, 1/4 W | 99-209037 |
6-14
Astec 5-Volt Power Supply Sub-Assembly Model SA40-1304 Parts List, Continued Ilustrated Parts Lists
| Designator | Description. | Part No. |
Transformers
| Tl | Com Mode Transformer Assembly | 99-209101 |
| T2 | Transformer, Power, AC8154 | 99-209100 |
| 3 | Control Transformer Assembly (J/V) | 99-209088 |
Miscellaneous
| Fl | Fuse, 2 A, 250 V | 99-209081 |
| Icl | Regulator, 431 | 99-209023 |
| 1c2 | Assembly, Regulator/SCR/Diode/Heat Sink | 99-209105, |
| IC2 | Regulator, UA7912 | 99-209106 |
| SCR1 | Assembly, Regulator/SCR/Diode/Heat Sink | 99-209105 |
| SCR1 | Thyristor, SCR, 2N6395 | 99-209108 |
| TM1, TM2 | Thermistor, 8 Ohm, +20% | 99-209099 |
| VR1 | Potentiometer, Trimming, 1K Ohm | 99-209098 |
| Z\ | Diode, Zener, 5.6 V, +5%, 40 mA | 99-209031 |
Illustrated Parts Lists
8 a = 5 se x3 28 Zo 5 Ze 55 ge 3° BS ze ee Bs $3 33 28 2s Ps bs ge ge 6 / as se § ‘ns 3° a 5 3B 3 gOS a) Be < ° lg 33 ss = & 8 ae
% 8 s N | A \
a $2 er
- / £ 99-10148 Lock Assembly
171027-001 A Lf fe ory re Ey i a fai
}-001. You can obtain a free Coin Controls Ltd. supplement (part. no. CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, Ireland. Telephone 062-52155. orem Screw 72-HA1404C
S x go
4 Coin Acceptors, Inc. Coin Door Assembly Figure 6.
6-16
Pot Shot Illustrated Parts Lists
99-10140 Panel Assembly
75-948S Locknut -_ 99-1016 Ix Lever 99-10152 BY = Right Coin Inlet " 5 ( Put 99-10147 A Harness 171006-035 oT a Coin Mechanism X< \ SOR.
y 75-944 S Locknut
99-10096 Fastener
99-10151 Left Coin Inlet
99-10080 Lamp Socket
99-10105 72-9406S Bar Screw
99-10104 Bar Retainer
99-10042 thru 99-1045 99-10154 Coin Switch Assembly Bracket Assembly
99-10150 ‘Switch Cover 99-10068 Coin Chute
65-4410 Coin Switch
99-10075 thru 99-10078 ‘Switch Wires,
‘99-10008 Retainer 75-14128 ‘Screw
Figure 6-4 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A
Illustrated Parts Lists
Coin Acceptors, Inc. Coin Door Assembly Parts List
Part No. Description 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x 1/4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 3/4-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch Wire (included in coin switch assembly 99-10043) 99-10076 Switch Wire (included in coin switch assembly 99-10042) 99-10077 Switch Wire (included in coin switch assembly 99-10044) 99-10078 Switch Wire (included in coin switch assembly 99-10045) 99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever
99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1-Inch Wide Die-Cast Coin Inlet Housing 99-10161 25¢ Amber Side-Entry Coin Button Assembly 99-15066 Screw for Clamp Metal Coin Mechanism for U.S, 25¢ 171006-035
6-18
Pot Shot Illustrated Parts Lists
7 78 & TS7a us74 xc.
1SA3 tse
az Coes
Figure 6-5 Pot Shot Game PCB Assembly A045052-01 B
6-19
Illustrated Parts Lists Pot Shot
Pot Shot Game PCB Assembly Part List
Designation Description Part No.
Integrated Circuits
| 1A, 1C, 1D | Integrated Circuit, MOC3011 | 37-M0C3011 |
| 2c | Integrated Circuit, 7406 | 37-7406 |
| 2D | Integrated Circuit, 7418273 | 37-741S273 |
| 2 | Integrated Circuit, 7418244 | 37-7418244 |
| 3c | Integrated Circuit, 7418245 | 37-74L8245 |
| 3D, 4/5C | Integrated Circuit, 7418244 | 37-74L8244 |
| 4B | Integrated Circuit, 6502 A | 90-6013 |
| 4C | Integrated Circuit, 7418244 | 37-7418244 |
| 4D | Integrated Circuit, 27256, 300 nsec | 136060-1101 |
| 5A | Integrated Circuit, 741932 | 37-741832 |
| 5B | Integrated Circuit, 74LS08 | 37-74LS08 |
| 5c | Integrated Circuit, 74LS139 | 37-74L8139 |
| SF | Integrated Circuit, TLO82CP | 37-TLO82CP_ |
| 6A | Integrated Circuit, 7419393 | 37-74LS393 |
| 6B | Integrated Circuit, 741914 | 37-741814 |
| 6c | Integrated Circuit, 74LS139 | 37-7418139 |
| 7A, 7B | Integrated Circuit, 741874 | 37-74LS74 |
| 7C | Integrated Circuit, 74LS00 | 37-74LS00 |
| 8A, 8B | Integrated Circuit, 7418393 | 37-74LS393 |
| 8D | Integrated Circuit, POKEY | 137430-001 |
Capacitors
| cl | Capacitor, Ceramic Disc, .01 pF, 125 VRMS | 120010-10. |
| c2 | Capacitor, 100 pF, 25 V, Electrolytic | 24-250107 |
| C3-C5, | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C6 | Capacitor, 39 pF, 100 V, Ceramic | 122016-390 |
| co | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 |
| c9, C10 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| Cll, C12 | Capacitor, Ceramic Disc, .01 pF, 125 VRMS | 120010-103 |
| C13-C15, C17-C25 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| €29-C31 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C32 | Capacitor, .001 pF, 50 V, Ceramic | 122002-102 |
| C33 | Capacitor, .22 pF, 50 V, +80% -20% | 122002-224 |
| C34 | Capacitor, .047 pF, 200 V, Polycarbonate | 122010-473 |
| C35, | Capacitor, .22 pF, 50 V, +80% —20% | 122002-224 |
| C36 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| 38 | Capacitor, 10 pF, 25 V, Electrolytic | 24-250106 |
| 39 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C40 | Capacitor, 100 pF, 25 V, Electrolytic | 24-250107 |
| C41 | Capacitor, 22 pF, 35 V, Electrolytic | 24-350226 |
| C42 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C43 | Capacitor, .22 pF, 50 V, +80% -20% | 122002-224 |
| C44-C47 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C48, C49 | Capacitor, .001 pF, 50 V, Ceramic | 122002-102 |
| €50-C52 | Capacitor, .1 fF, 50 V, Ceramic | 122002-104 |
| 53 | Capacitor, 22 pF, 35 V, Electrolytic | 24-350226 |
6-20
Pot Shot Iustrated Parts Lists
Pot Shot Game PCB Assembly Part List, Continued.
Designation Description Part No.
| C54 | Capacitor, .22 pF, 50 V, +80% —20% | 122002-224 |
| C55 | Capacitor, 10 pF, 25 V, Electrolytic | 24-250106 |
| C56, C57 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
Diodes
| CRI | Diode, MV5053, Light-Emitting | 38-MV5053 |
| (CR2-CR7 | Diode, 1N4001 | 31-1N4001 |
Inductor
| il | Inductor, 100 pH | 41-3003 |
Transistors
| Ql | Triac, 2N5756, 2.5 A RMS, 400 V | 133035-003 |
| Q2 | Transistor, 2N5306 | 133033-001 |
| Q3 | Transistor, 2N3904 | 34-2N3904 |
| Q5 | Triac, 2N5756, 2.5 A RMS, 400 V | 133035-003 |
| Q6, Q7 | Transistor, 2N3904 | 34-2N3904 |
| Qo | Triac, 2N5756, 2.5 A RMS, 400 V | 133035-003 |
| QU, Q12 | Transistor, 2N5306 | 133033-001 |
| Q13, Q14 | Integrated Circuit, TDA2030 | 137301-001 |
| Q15 | Transistor, 2N5306 | 133033-001 |
Resistors
| R1 | Resistor, 10 K Ohm, +5%, 1/4 W | 110000-103 |
| R2 | Resistor, 1 K Ohm, +5%, 1/4 W | 110000-102 |
| R3 | Resistor, 100 Chm, +5%, 1/4 W | 110000-101 |
| R4 | Resistor, 220 Ohm, +5%, 1/8 W | 110027-221 |
| RS | Resistor, 240 Ohm, +5%, 1/8 W | 110027-241 |
| R6 | Resistor, 100 K Ohm, +5%, 1/8 W | 110027-104 |
| R7, R11 | Resistor, 220 Ohm, +5%, 1/8 W | 110027-221 |
| R12, R13 | Resistor, 10 K Ohm, +5%, 1/8 W | 110027-103 |
| R14 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| R16 | Resistor, 470 Ohm, +5%, 1/8 W | 110027-471 |
| R17, R18 | Resistor, 150 K Ohm, +5%, 1/8 W | 110027-154 |
| R19 | Resistor, 10 K Ohm, +5%, 1/4 W | 110000-103 |
| R20 | Resistor, 1 K Ohm, +5%, 1/4 W | 110000-102 |
| R21 | Resistor, 100 Ohm, +5%, 1/4 W | 110000-101 |
| R22 | Resistor, 220 Ohm, +5%, 1/8 W | 110027-221 |
| R23, | Resistor, 150 Ohm, +5%, 1/8 W | 110027-151 |
| R24 | Resistor, 4.7 K Ohm, +5%, 1/8 W | 110027-472 |
| R25 | Resistor, 470 Ohm, +5%, 1/8 W | 110027-471 |
| R26 | Resistor, 4.7 K Ohm, +5%, 1/8 W | 110027-472 |
| R27, R29 | Resistor, 470 Ohm, +5%, 1/8 W | 110027-471 |
| R30 | Resistor, 10 K Ohm, +5%, 1/4 W | 110000-103 |
| R31 | Resistor, 1 K Ohm, +5%, 1/4 W | 110000-102 |
| R32 | Resistor, 100 Ohm, +5%, 1/4 W | 110000-101 |
| R33, R37 | Resistor, 220 Ohm, +5%, 1/8 W | 110027-221 |
| R38-R50 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| R54-R58 | Resistor, 470 Ohm, +5%, 1/8 W | 110027-471 |
| R62-R69 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| R70 | Resistor, 470 Ohm, +5%, 1/8 W | 110027-471 |
6-21
Illustrated Parts Lists
Pot Shot Game PCB Assembly Part List, Continued
Designation Description Part No.
| R71 | Resistor, 22 K Ohm, +5%, 1/8 W | 110027-223 |
| R72 | Resistor, 3.3 K Ohm, +5%, 1/8 W | 110027-332 |
| R73 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| R74 | Resistor, 1 Ohm, +5%, 1/8 W | 110027-010 |
| R75, R76 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| R77 | Resistor, 0 Ohm, 45%, 1/4 W | 110005-001 |
| R79 | Potentiometer, 10 K Ohm, Horizontal | 119002-103 |
| R80 | Resistor, 10 K Ohm, +5%, 1/8 W | 110027-103 |
| R85, R86 | Resistor, 150 Ohm, +5%, 1/8 W | 110027-151 |
| R87, R88 | Resistor, 10 K Ohm, +5%, 1/8 W | 110027-103 |
| R89 | Resistor, 1 Ohm, +5%, 1/8 W | 110027-010 |
| R90 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
| ROL | Resistor, 22 K Ohm, £5%, 1/8 W | 110027-223, |
| R92-RO4 | Resistor, 1 K Ohm, +5%, 1/8 W | 110027-102 |
Connectors
| Ja, J2 | Connector, 11 Circuit, Header, .100 Ctr | 179118-011 |
| 3B | Connector, 6 Circuit, Header, .156 Ctr | 179213-006 |
| i4 | Connector, 6 Circuit, Header, .100 Ctr | 179118-006 |
| ab) | Connector, 6 Circuit, Header, .250 Ctr | 179069-006 |
| J6 | Connector, 2 Circuit, Header, .156 Cir | 179213-002 |
Sockets
| 4B | Socket, 40-Pin | 79-4240 |
| 4D, 5D | Socket, 28-Pin | 79-42C28 |
| 8D | Socket, 40-Pin | 79-42C40 |
Miscellaneous
| X1 | Crystal, 3.579 MHz | 144007-001 |
| HS1 | Heat Sink, TDA2030 | 178190-032 |
| 7D/E | Switch, 8-Position DIP | 160031-008 |
| 4E | Switch, 8-Position DIP | 160031-008 |
Test Point 179051-001
6-22
Pot Shot Illustrated Parts Lists
N O T E S
6-23
Illustrated Parts Lists Pot Shot
P3 >
| eno |7 | at | 1| oN | + |
+5v | 6 2| +5v
| GND /12 | ey | 3| GND | POT SHOT MAIN PCB | BE g |
| +12v | 4 | a | 4] #12V | SCHEMATIC 045052-01 | 33 3 |
| cud | 5 | R | 5| GND | se 4 | |
| +5v [1 | 6| +5V | rr | | |
14 43 Se aa 86 s aloo me [-anene .
| 2 | Se) hy | 7 |
Zz} > 3)8) >| >|s|8] 3) P32
| — | vio | cv_/; | cr |
| neurra | 4 (28 | OR | 9 | OR ©) LAMP 2 |
BN | 5 BN
| neurraL | 5} | oR |) | OR 6) LAMP 1 |
P50 BK OR or (,{ 7 BU Neutral 8 aN | 3 GN SCREW ow 3 Y MOTOR 115 VOLTS oe a NO R ‘ouT ae P51 oR oR
| NEUTRAL | 8 | fi | ( Mi carrouse |
ny
| une | 1% | y45 | 1) }OTOR |
Ni x Os P52 &
| OR | . | OR | L | x |
| NEUTRAL | 9 | a i | = | MV sHooTeR |
MOTOR LINE, 2 foo ogote v 3
- INTERLOCK INTERLOCK POWER SUPPLY WIRING DIAGRAM — 045119-01 304 P31A BK BK_/, |
| 115 volts | 1 | * | 1 |
| our | 2 1S | * | eo |
a a Pd P31B =e >> KT] R(ea ne ¢ cu 2
P3ic
| BK _/, | FLUORESCENT | > |
| GN | 5 | UGHTS | Pata |
as wii at an
| 3308 | P3iD | a | : |
“ Sy
| + [BK | BK_/, | a3 |
| 115 vorts | 9 [GN | |} | 2 sx |
| ‘ouT | Ww. | Ww |
| 3 | 3 | ma |
PSHE g 4 BK_(| 3 oN |)
6-24
Figure 6-6 Game Wiring Diagram P24 R/W R/W
GY
oY z BALL COUNTER +5V
ae P25 Ww
BALL COUNTER
BALL | 9 |_BK 5 | 16D 3 — BALL
4 | KEY
BK
BK GND
GND
BN ‘START
W/BK | 5 | test 7 | TT
OR COIN 2
9 | COIN 1 10| KEY
START SW
BK/W
- +5V BU/W | § | coIn CNTR 2 BK/W START LIGHT
fo} SEE P/N 99-15085 FOR COIN DOOR WIRING vA +12V
W/8K BU/W VW OR/W COIN CNTR 1
oR/w 4 +12V 1 | +5V AUDIO 4 AUDIO 2
Blan
Sls
The
n
PSS RUNS P29
SEE A044328-01 FOR COMPONENT WIRING DIAGRAM ust
‘SPEAKER Illustrated Parts Lists
6-26 Figure 6-7 Power Supply and Coin Door Wiring Diagrams Astec 5V 5-Amp/12V 1-Amp Power Supply Wiring Diagram ay av cow Illustrated Parts Lists
Figure 6-7 Power Supply and Coin Door Wiring Diagrams, Continued
6-27 fe tAasov reo ScKCarn Ty
Ft rer FS sags fe} ancsov ee, [oN pats Be AS. wrures | -
notes ev ACTERMATE WIRE COLOR SHOWN: |
(nereaiverst seis 343} ASTES SwwrTeninie POWER SUPALY.
b —~Ve_8 ne RIGHT COIN SWITCH | c Bi
LEFT COIN SWITCH
SW GND
RIGHT COIN SW
LEFT COIN SW
CHASSIS GND
i ' I ' I i L.
Coin Door Wiring Diagram
Ilustraied Parts Lists
Alfustrat
+5y A
R17 ted Parts Lists
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden with- ‘out the specific written permission of Atari Games Corporation, Milpitas, CA. This drawing is only conditionally issued and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any desiga or technical information shown thereon, nor any right to reproduce this drawing, or any part thereof. Except for ‘manufacture by vendors of Ati Games ration, and for manufacture under the corporation's written license, no right is granted to re produce this drawing or the subject matter thereof, unless by written agreement with or ‘written permission from the corporation. Pree
7NMI 7IRQ
7RESET AUF y se BPH2
| 45}A | ys | BR/H- |
| 13/9 | pall | —_—— iAi3__ |
| ttlq | yf | BAL? |
+ BAii
| sla | F | yz | |
| bla | 4 | y|te | BaLO |
| Hla | y [te | BAY |
2 18 WZUY7I
= GND 2 18 A uct BAZ
| Ha | vite | a | |
| Sia | ye | _— | BAS. |
8\A yi2_ BAY <
| ttle | FZ | yf | |
| tale | a | yz | Raz |
| 15]q | ys | Bat |
ar 3 pa0 Fac rec a ]i4
=eND . >——— BR/h-
16)
i]
cr
TF
FE]
i1|
Mlustrated Parts Lists
et B 13 6B, BA 2am ree 13 ett woo & ya /entL Usa qc ~ vobL— /RAM
“LAR /SWRD 7CACK /BACK 70PS /POKEY
SHT 2
4D SHT 2
2alea 8K8-70A IS ao o> [xv Jor fer f= fev [Or J |S
&
Figure 6-8 Pot Shot Game PCB Schematic Diagram, Sheet 1
6-29
Illustrated Parts Lists Pot Shot
SHT 1 Road Road RE7S Ree $ ik 1k = 4k 3 1k oe a 307] PE
| Hla | Y | 3 | Alay | |
| Hoole | t | S/A | y | aN or alas |
| alg—o} | eo | slay | tae | EE] |
| 1312—Sle | tila = y/o | qv | alr | |
| ala Oo yz | iz] | Alp |
16 fay
| 4E | 15}q | y{S | mY Ss Ae |
| at | 3 | ey oS Ay |
Fac ec : i s , rezk Road Rows Re v0) :
+ a < $ 1K 3 aK 3 1K 3 1K 7aPs +5V
& Ss 4 0 3 iD z 40 De NODELOS 34 ID all 38 mn 18 Ps [14 re) ¢ gis. 120 Db a [te
| l2a. | 5 | 4 |
=o le Ca |23 Lee 7LWRE ler [28
2 PR 37__ pauD
J2-44
J2-10
J2-9>
J2-8
J2-7
J2-6
J2-5
J2-3
+5V Mlustrated Parts Lists
as NOTICE TO ALL PERSONS ——_ J1-2 ‘RECEIVING THIS DRAWING Ja-3 CONFIDENTIAL: Reproduction forbidden with- ‘out the specific written permission of Atari Ji-4 Games Corporation, Milpitas, CA. This drawing is only conditionally issued and neither receipt = GND nor possession thereof confets or transfers any
| —— | rs | SJ1-5 | right in, or lense to use, the subject mater of |
RE the drawing or any design or technical informa-
| START | 54-6 | tion shown thereon, nor any sight to reproduce |
| ‘1k | RUB | this drawing, or any part thereof. Except for |
| AW\- | TILT __y j4-7 | ranufacture by vendors of Atari Games Corpo- |
| R47 | 4k | rauon, and for manufacture under the corpora- |
| COIN2 | _» j4-8 | Hons writen license, no ight i granted t te |
roduce this drawing or the subject matter
| ine | COINI | y j4-4 | Thereof unless by waten agreement with or |
| if | [ | twiten permission fom te exporton. |
ices tc24 1co23 1c22lc21
| . | 7.4 | es | aL | ve | ot |
+5V-<a-—__ 1-11
=GND Rit Rd
| +5V | ji | af | iB | |e | TRIS _y j5-5 |
| cet | ec | | 220-2 | we | 3 OF | R10 |
rs 2 Moc3011. 2NS756 too cc2 Uo 27 | RS cB 10K zt To TRIS _y 45-2 R37 R35
| af | ie | ______, | TRIS | > 5-1 |
[¢ —AAA- 220 fe A J" |mocs011 £ 4
MOC304: aio 2NS5756
£ _ /RESET C508 Fy 3 9 2N5756
Lc12 IRA 5-3
Figure 6-9 Pot Shot Game PCB Schematic Diagram, Sheet 2
6-31
Illustrated Parts Lists
Qi. R75 2NS306 cz ff ) does 1 rt
PAUD +SV +12 4 $V yyy
c30 cos j Cry yg tan 1 = $Réoos
couA 12 ie] ors pre 2N5306 =. > Ju-2 cei) _ can | cosB 1K + 8 Cts yey
ft ND Hd $Réoo1
cage G2. > jy-6
R90
- 1K
cnn
e535 i0
=AGNO
R71 22k
R79
=AGNo
FSLi
a
Lsos 5B
Lso8 i" re
Lsos
6-32 as 2N5306 FSL_y jy-5
SPARE GATES
4 2c # ety Uoe ts32 7c. a2
TS00 $32
tc,
S00 S32 +12V SING SF, 3 id a TLOS2
AGND
+12V f Ulustrated Parts Lists
C4,5,9,10, le 13-15,17-20 100
C BYPASS)
+12U A
1OA2030 Qi3 iRtoos wan GND _» 33-5
Ret
MTG HOLE 3-3
+a2y J3-4 > Jo-2
RBq
J3-1
C54 Ra2 ee
1K
=AGND
R72 3.3K
R73 1K
L534 55
SRCND
NOTICE TO ALL PERSONS
RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden with- ‘out the specific written permission of Atari ‘Games Cotporation, Milpitas, CA. This drawing, is only conditionally issued and neither receipt ‘nor possession thereof confers or transfers any right in, or license to use, the subject mater of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing, or any patt thereof. Except for manufacture by vendors of Atari Games Corporation, anid for manufacnure vader the corparation's writen license, no right '5 granted to reproduce this drawing or the subject matter thereof, unless by wricten agreement with of written permission from the corporation.
Figure 6-10 Pot Shot Game PCB Schematic Diagram, Sheet 3
6-33
Illustrated Parts Lists Pot Shot
N O T E S
6-34
AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for is low. ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is ap-
plied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panei, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING ‘Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.
CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC curtent while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM. A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.
Glossary
COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.
CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in ore direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors, DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory.
gl-1
DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically aiterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE
- A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
- A circuit in which one signal switches another signal on and off.
- To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. Vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.
gl-2 LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed. inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request.
PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. ‘TROUBLESHOOT The process of locating and repairing a fault.
VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. ‘WATCHDOG A counter Circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035