Krull Instruction Manual (May 1983)
Krull (Gottlieb, 1983) · Instruction Manual · 43 pages · 28 sections · original scan
I
t Instruction Manual
: .
i éz0lttlieb
KRULL (GAME GV-105) INSTRUCTION MANUAL
TABLE OF CONTENTS
SEC. PAGE
I, 2 INSTALLATION... 55. sr oe 1 I= > SINIALIZATION 2 3
Il. GAME OPERATION..................000.....00060- 3
IV. GAMEPLAY AND SCORING...................... 4 V. SOUND/SPEECH ........ 0000... ooo ee ec eeceeeeee 6
VI. GAME ADJUSTMENTS/OPTIONS ................ 6
Vil. BOOKKEEPING AND SELF TEST ................. 7
VII. GENERAL INFORMATION ........................ 9
IX THEORY OF OPERATION......................... 1
X. | WIRING AND SCHEMATIC DIAGRAMS .......... 12
XL PARTS INFORMATION ............................ 33
WELLS GARDNER MONITOR, SERVICE AND OPERATION MANUAL (Attached)
“WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”
NOTICE
WARRANTY INFORMATION IS LOCATED ON THE INSIDE BACK COVER.
FOR SERVICE, CALL TOLL FREE: 1-800-323-9121; (ILLINOIS) 1-800-942-1620 eas Qa wa rer rom rear mae =e ee , ia ae a z= r.Cté<C*S Se al r.té«<‘* Steen _
I. INSTALLATION
GAME ADJUSTMENT SWITCHES [PART OF Al LOGIC BOARD}
COIN CHUTE COIN CHUTE COIN CHUTE FRONT DOOR #2, LIGHTS 1 INTERLOCK
ASSY.
COIN SWITCH, a
COIN SWITCH #2 MA457 FILTER BOARD ASSY.
MA-487 ‘Ab SOUND BOARD ASS.
MA492 A3 POWER SUPPLY ASSY.
MA456 Al LOGIC BOARD ASSY,
ELECTRONICS BOARD
PLAYER SWITCHES {TYPICAL}
JOYSTICK ASSY. (TYPICAL) ASSY, A458 CONTROL PANEL
MA-300 SERVICE PANEL
STEP/TEST SELECT TEST SWITCH SWITCH VOUME COIN CONTROL METER
MA-375 F3 Fa BRIDGE FS F2 BOTTOM PANEL = MONITOR 9VAC RECTIFIERS 'SVAC 6.3V AC ASSY, FUSE FUSE FUSE FUSE
SERVICE ‘OUTLET
I. INSTALLATION
A. SET—UP
- Carefully inspect the exterior of the game for any damage which might have occurred during shipment.
- Unlock and open the rear cabinet door.
- Check that all plug in connectors are seated firmly. The connectors are keyed so they will only go in one way.
- Remove the binding strap from the line cord, and install the line cord plate in the groove provided (see photo).
- Cabinet levelers (2) are stored within the cash box for shipping purposes. Install and adjust as necessary.
LUNE CORD PLATE
B. CHECK-OUT
- Check that all cables are free of moving parts.
- Check for any loose wires.
- Check far loose solder or foreign matter on switches and power supply assemblies.
- Be certain all fuses are seated firmly.
- Be sure transformer wiring corresponds to the supply voltage.
- Refer to section VI to make all the necessary game adjustments.
- Reassemble the game.
- Plug the line cord into a properly grounded 3-wire receptacle ONLY!! c CONTROL PANEL REMOVAL 1, Unplug the game.
- Unlock and open the coin chute door.
- Reach in through the coin chute door and remove the wing nut and flat washer from each of the two carriage bolts which secure the control panel to the game. Unlatch the control panel atch at the top center of the panel. Note where the latch strike plate is located. Remove the carriage boits.
- Pull the control panel back, grasp it at the front edge as far back as it will go (approximately 4").
- Raise the front of the contro! panel approximately one inch above its supports and lift the entire assembly high enough to disconnect plug A9J2/A9P2.
- Remove the entire control pane! assembly from the game.
- The joystick’s and leaf-switches are now accessible for removal or cleaning.
- For reassembly, reverse the above procedure.
MONITOR REMOVAL
- Unplug the game.
- Perform the contro! panel assembly removal procedure (Section C).
- Unlock and open the rear cabinet door. 4, NOTE: The color monitor contains HIGH VOLTAGES delivering LETHAL quantities of energy. Do not attempt to service the monitor until you have shorted the anode plug on the picture tube to ground.
- Disconnect the video plug Al7JI, the monitor power supply plug Al2ZJ3/A12P3 and the ground wire from the monitor chassis.
- From the rear of the game, remove the one nut and one washer from each of the four carriage boits used to secure the monitor to the platform.
- Remove the monitor from the rear of the game, being careful to clear all cables from the CRT neck.
- For reassembly, reverse the above procedure.
I. INSTALLATION , ‘I. INITIALIZATION, Ill. GAME OPERATION
I. INSTALLATION
E. SPEAKER ASSEMBLY AND MARQUEE REMOVAL
- Unplug the game.
- Unlock and open the back door.
- Unplug the Al5-JI/PI connector.
- Unlatch the two latches on the rear of the Speaker Assembly Panel located inside the back door above the monitor.
- On the front of the game, pull down on the lower molding under the marquee. The Speaker Assembly will lower to allow removal of the marquee.
6, Remove the marquee by lifting it upward out of its track. The Speaker Assembly and {llumination Assembly are now accessible for servicing.
- Tilt the front of the Speaker Assembly downward while lifting the center upward. Pull the assembly straight out to remove. Be careful not to pinch the Speaker Assembly cable.
- For reassembly, reverse the above procedure. When replacing the marquee: a. Tilt the front of the Speaker Assembly downward. b. Place the bottom of the marquee in the lower molding track on the front of the assembly. c. Apply slight pressure with your thumbs to the lower left and right corners of the marquee. d. Slowly raise the Speaker Assembly until the top of the marquee is in place in the upper track in the top molding. e. Be certain to reconnect the Al5-J1/P1 connector and relatch the rear assembly latches.
I. INITIALIZATION
TURN GAME ON B. The playing field cycles through the following: Immediately, the coin chute lamps and the 1. High Game to Date screen speaker marquee lamp will turn on. 2 Instruction Set
- Game Play Cycle
AFTER A TEN SECOND DELAY A. The attract mode appears on the screen.
Il, GAME OPERATION
A. GAME START Cc. SECOND PLAYER
- Insert coins into coin chute. 1. Additional player is indicated by the words a. Coin chute tune is played. “COLWYN 2” and a zero in the second b. Total credits are displayed on screen. Player's display.
- Press one or two player button to start game.
a. Total Credits are decreased by one. D. COLWYN’S/EXTRA COLWYN’S b. Game initializes. 1. Each player will begin with three Colwyn’s (dependent on Option/Parameter settings). B. FIRST PLAYER 2. Extra Colwyn’s are earned by achieving
- The first player's score displays a zero. certain score levels (dependent on
- The other player's display will be blank. Option/Parameter settings).
1V. GAME PLAY AND SCORING
HOW TO PLAY
CONTROL PANEL The Jeft joystick controls the movement of the Player character, Colwyn. He can be moved in any one of eight directions. The right joystick controls the movement of the players weapon, the glaive. It can be thrown in any one of eight directions. Four glaives can be in flight at one time and will return to Colwyn with a boomerang-type action. The one and two player select buttons are also located on the panel. Krull consists of five subgames: (1} The Mountain Game, (2) The Swamp Game, (3) The Fortress Game, (4] The Hexagon Game and (5) The Beast Game. The player must accomplish a task in each of the five games with eight levels of difficulty in each. All eight levels can be reached in one task based on the time spent performing that task (amount of time spent on that subgame). The total number of lethal characters on the screen at one time increases as the levels increase.
“FROM THE SKY WILL COME THE BLACK FORTRESS. FROM THE FORTRESS WILL COME THE SLAYERS, TO DEVOUR THE PLANET OF KRULL. THEN SHALL A GIRL OF ANCIENT NAME BECOME QUEEN, AND THE KING SHE CHOOSES SHALL RULE THE PLANET.”
The planet Krull is threatened by the Beast. His army of Slayers has brought terror to the land. Colwyn must stop this terror and save the land and its people. On the day Colwyn is to wed the Princess Lyssa, the Slayers, army of the Beast, kidnap her to become the Beast’s bride. Colwyn must reach the Black Fortress and reclaim his Princess. He who marries the Princess shall be king. The Beast must not be allowed to rule the planet. A prophet acquaints Colwyn with the magical properties of the glaive, a five-bladed sword, which Colwyn must acquire. To accomplish this task, he must climb the mountain and collect the five individual blades of the glaive in order to assemble the weapon. The blade is picked up by touching Colwyn to the blade. Boulders are fatal and must be avoided. The weapon joystick is not utilized in this subgame. The player is awarded 1000 points for each biade picked up. Points are also awarded for placing Colwyn in a dangerous Position in front of one or more boulders. During his travels to discover the Black Fortress, Colwyn comes upon an army of eight men that he befriends and recruits to help him in his quest to destroy the Beast so that Krull can be safe from his evil.
With no intentions of losing his newly acquired bride without bloodshed, the Beast orders an army of Slayers to stop Colwyn and his friends. Forging through the quicksand-riddled swamps, Slayers materialize from the soil and Colwyn Prepares for battle. In the second subgame, Colwyn must save as many friends as possible while killing all of the Slayers. The friends are saved by touching them and the Slayers are destroyed by the glaive. The Slayers themselves and their spears must be avoided. The game begins with eight friends. The number of friends saved is the number of friends carried over into future subgames. The friends can eliminate the Slayers with hand-to-hand combat but can also be destroyed themselves. Receiving three blows either by hand-to-hand or by the Slayers spear is fatal to the friends. The subgame ends when there are no longer any friends to save and all of the Slayers have been eliminated. Avoid quicksand, as it slows Colwyrés attack. Each friend saved awards 1000 points (maximum 8000 points) and 100 points for each Slayer the player eliminates.
After days of travel, Colwyn and his men have found the Black Fortress in the Iron Desert where many dangers await them. While attempting to lead his men through the dangerous narrow passageways that lead to the Fortress, Slayers materialize once again in a second attempt to stop Colwyn’s struggle. In this third subgame, Colwyn must pick up all of his friends and deposit them safely into the hexagon while again combating the Slayers. The total number of friends in this subgame is equa! to the total number of friends saved in Subggame 2. This subgame concludes
1V. GAME PLAY AND SCORING
when all of the friends have been delivered to the hexagon. The player is awarded 1000 points for each friend delivered to the hexagon, 100 points for each Slayer he destroys and 100 points for each Slayer remaining when the last friend is delivered to the hexagon.
Victorious in battle, Colwyn must now attempt to release his friends from the hexagon. Unlike entry, exiting the hexagon is a struggle deservant of its own merit. Once again Colwyn must call upon the power of the glaive. Release of his friends is accomplished by throwing the glaive at the front wall while it is black only. Any glaive striking the wall while it is not black will stick in the wall until the wall becomes black. The Slayers, of course, attempt to stop Colwyn’s efforts. In his own attempt for survival, Colwyn must fight them off and avoid their spears. The subgame ends when the last black wall is broken through and the friends have escaped. The player is awarded 100 points for each Slayer he puts an end to, 100 Points for each Slayer remaining when the friends are set free and 1000 points for the first black wall destroyed, 2000 points for the second, 3000 points for the third and 4000 points for the fourth. Now inside the Black Fortress, Colwyn secedes from his friends in order to rescue the Princess Lyssa. He finds her in a large cave carefully guarded by the Beast. He knows that the only way to reclaim his bride and conserve the planet is to forge into battle with the Beast. In the fifth subgame, the player moves Colwyn towards the Princess in order to reach her. As he progresses, the Beast attempts to stop him by throwing fireballs at him. The fireballs must be avoided or destroyed by the glaive. If not destroyed, the fireballs will ricochet off of the walls. Destroying a fireball awards the player 100 points multiplied by the number of fireballs in flight. The Beast is momentarily stunned when hit with a glaive and awards the player 100 points. The Beast cannot be destroyed and the player mi'.t avoid touching him. When Colwyn reaches the Princess, his friends, following the pandemonium of the battle, appear and chase the Beast off, awarding 1000 points per friend. The total number of friends in this subgame is equal to the total number of friends saved in Subgame 2.
V. SOUND, VI. GAME ADJUSTMENTS / OPTIONS
Vv. SOUND
The Sound Board installed in this game has been programmed for sound only. The switch bank on the Sound Board is not used and the switch Positions have no effect on the sound.
Vi. GAME ADJUSTMENTS/OPTIONS
CONTROL BOARD B. SOUND ADJUSTMENTS SWITCH ADJUSTMENTS The audio output is controlled by the potentiometer mounted on the service panel SWITCH 1 LIVES PER GAME
| OFF. | ++ B LIVES | assembly (located inside the coin mechanism door). |
ON «5 LIVES
—— ATTRACT PLAY «SOUND .NO SOUND
COIN/CREDITS vi Turning the potentiometer counter-clockwise will decrease the volume. Turning it clockwise will increase the volume.
| a | ee | of | installed on the Sound board have been |
| ON | ON | FREE PLAY | factory adjusted. The potentiometer |
SWITCH 5. HEXAGON CONTROL settings should never be changed when
| on | SON ART | performing the recommended calibration |
procedure. ———S DIFFICULTY CONTROL NORMAL ++» HARD c MONITOR ADJUSTMENTS Normally, few if any adjustments are required
| 7 | 8 | EXTRA LIVES |
FIRST EXTRA EACH ADDITIONAL for proper monitor operation. However, after
OFF 30,000 POINTS EVERY 50,000 POINTS any major repairs to the monitor chassis refer to OFF :40,000 POINTS EVERY 50,000 POINTS On +30,000 POINTS EVERY 30,000 POINTS the attached monitor manual. ON 50,000 POINTS EVERY 75,000 POINTS
Vil. BOOKKEEPING AND SELF TEST
SELF TEST The battery back-up bookkeeping functions of this game are contained in Self Test steps 3 and 4. These are in addition to the electro-mechanical coin counter located inside the front door panel. Every time a coin is inserted into a coin slot, the counter is energized, incrementing the count.
The self-test consists of six functions which may be used to identify problems in the video system and to change program parameters. The self-test mode is entered by setting the self-test toggle switch located inside the cash door to “TEST”. A selection of available tests is displayed on the monitor. To return to the GAME mode at any time, the operator needs only to set the toggle switch back to “GAME”.
Selection of tests is done with the push button switch labled “SELECT”. Upon entering the test mode, a flashing arrow points to the first test selection. Momentarily depressing the “SELECT” button will advance through each selection one by one. When the arrow is pointing to the desired test, the operator may begin that test by pressing the “SELECT” button and holding it down until the test appears on the screen.
Once a test has been selected, the operator can return to the selection list by holding down the select switch until it re-appears. The six tests are as follows:
- MONITOR ADJUSTMENT Four patterns can be displayed on the screen for adjusting monitor color, brightness, contrast and convergence. The patterns are: Color bars, a cross-hatch, a gray scale, and a dot pattern. By momentarily pressing the select switch, the operator may cycle through the four patterns.
- MEMORY TEST
For each RAM memory chip: An OK or an NG (no good) appears signaling that the chip is good or bad respectively. Check sums are displayed for each ROM memory chip. If you have a suspect ROM, refer to your distributor for the correct check sum number.
- DIP SWITCHES A functional description of the eight Dip Switches located on the Logic Board Assy. is displayed. Changing any switch will cause an immediate update of the description displayed on the screen.
- BOOKKEEPING Selecting this test will display a menu of four functions. Pushing the SELECT button momentarily will move an arrow on the screen. When the arrow points to the desired function, press either start button on the control panel to perform that function.
DISPLAY SCORE COUNTS — A table is shown
with 20 categories of score values by thousands (K] and a count associated with each category. The count represents the number of plays in which the score at the end of the game fell into that category. In addition, a high score, low score, and average is shown along with the total number of plays on which the average is based. To clear the table, press either start button and return to the menu by holding down SELECT.
DISPLAY TIME COUNTS — Same as above except each category represents play times in seconds. The high, low, and average are given in minutes and seconds. DISPLAY ROUND COUNTS — Same as above except each category represents the round in which the games ended.
- SWITCH TEST A colored square is displayed for each player button. Pressing a button causes the appropriate square to change color. For each cain mechanism, a digit is displayed (initially 0). Inserting a coin into a coin
Vil. BOOKKEEPING AND SELF TEST
chute will increment the appropriate value without affecting the coin meter. Moving the MOVE joystick will display its direction of movement in the upper right corner of the screen. Moving the FIRE joystick will display its direction of movement directly under the MOVE joystick display.
SOUND TEST After selecting this test a count will appear on the screen representing the various sounds that are produced by the game. There will be 28 different sounds produced and the screen count will repeat to OI. Pressing either Start button will suppress all sound output and speed up the count so a particular sound can be sought out and checked.
c.
Fl F2 F3
FS
Ful F2) F31 F32 VII. GENERAL INFORMATION
A. PRINTED CIRCUIT BOARDS ARE DESIGNATED AS FOLLOWS:
Al Logic Board Assy.
A3 Power Supply Assy.
A6 Sound Board Assy.
A8 Filter Board
B. WIRE COLORS ARE SHOWN AS NUMBERS:
0 Black | 5 Green 1 Brown 6 Blue
2 Red 7 Purple
3 Orange 8 Slate
4 Yellow 9 White
For example, 688 is a BLUE- SLATE-SLATE striped wire.
FUSES
BOTTOM PANEL
Primary Power 4 Amp SLO-BLO. 6.3 VAC 3 Amp SLO-BLO Monitor 2 Amp SLO-BLO. 9 VAC 10 Amp SLO-BLO 15 VAC 1 Amp SLO-BLO
POWER SUPPLY ASSY. (A3} +5VDC Source 6 % Amp SLO-BLO
| Sound Board Assy. | +16VDC | 2 Amp SLO-BLO |
| Sound Board Assy. | +12VDC | % Amp SLO-BLO. |
| Sound Board Assy. | -12VDC | %& Amp SLO-BLO |
| Coin Meter | +20VDC | 1 Amp SLO-BLO |
Vill. GENERAL INFORMATION
POWER SUPPLY SPECIFICATIONS
LOCATION PROTECTION
Logic Board Assy. Voltage adjustable. 6 Amps over-voltage Protection and fused for over-current protection. Sound Board 2 Amps fused for over-current protection. The reference for this circuit is aIN4¢745A +16VDC Zener controlling the base of an emitter follower pass transistor.
Sound Board +12VDC -12VDC 100 milliamps fused for over-current protection. The plus and minus 12 volts supplies are the 7812 and 7912 IC regulators respectively. Coin Meter +20VDC Full wave rectified unfiltered voltage, fused for over-current protection.
Coin Chute Lights +4.5VDC Full wave rectified unfiltered voltage, fused for over-current protection.
Monitor and Marquee TOOVAC or N5VAC, GOHZ Isolated, fused AC voltage.
IX. THEORY OF OPERATION
INTRODUCTION The character based graphics system designated GG-IIl has two main subdivisions. The first subdivision is the Central Processor Unit (CPU) which has three partitions: a. Microprocessors b. Memory c_ Input and Output ports (I/O)
The Intel 8088 microprocessor is used and 32K bytes of memory is reserved for programming space and has 5 input ports and 5 output ports. The second subdivision is the video state machine which generates and controls the video signal to the Monitor. The state machine has three partitions: a. System Clock (CLK) b. Foreground generator (FGND) c Background generator (BGND)}
The system clock is driven by a 2OMHZ crystal, divided down for a 5MHZ dot clock.
All inputs and outputs including the video control and general purpose I/O are memory-mapped, (i.e. everything within the system can be addressed in a single segment of 64K addresses as memory]
The video control unit is divided into an “objectoriented” foreground driver and “character-oriented” background driver. The screen resolution is 256 pixels horizontally, and 240 lines vertically for both foreground and background. The CPU communicates with the foreground driver and background driver by writing data into the designated memory areas in a certain format. The foreground is designed to display moving objects on the screen with a minimum overhead to the processor. The game programs will only have to specify the vertical and horizontal position and the object select number to the foreground driver. The background video supplements the foreground with relatively static figures on the screen. The CPU specifies all the character positions on the screen with desired “character ” patterns.
A 5MHZ system clock drives a 9 bit horizontal dot counter and an 8 bit vertical line counter. The horizontal counter counts from 0 to 255 during active scan line and 256 to 317 during horizontal blanking time. When the horizontal counter reaches 317, the horizontal counter resets to 0. At the beginning of the horizontal blanking time (horizontal counter = 256) it increments the vertical counter. The vertical counter counts from 0 to 239 during active vertical scan time and 240 to 255 during vertical blanking time.
The battery backup system supports two battery RAM’s that store all of the bookkeeping functions. The battery is maintained at a +3.6V reference by a trickle charge supplied on the logic board regulated by a current limiting resistor. If the AC power to the game is interrupted, the battery allows the RAM’s to store the data contained in the Distrubutors table and the Options/Parameters screen. X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
TABLE OF CONTENTS
LOGIC BOARD ASSY. [A1) COMPONENT LOCATION AND PARTS LIST ...........0.000.0ceeee ee eee 13 SCHEMATIC DIAGRAM (SHEET 1 OF 3) SCHEMATIC DIAGRAM (SHEET 2 OF 3} .. 18 SCHEMATIC DIAGRAM (SHEET 3 OF 3) .. 21
POWER SUPPLY ASSY. (A3} COMPONENT LOCATION AND PARTS LIST . 24 SCHEMATIC DIAGRAM 25
SOUND BOARD ASSY. {A6) COMPONENT LOCATION AND PARTS LIST ...........-0-0.0.0c0ee eee 27 SCHEMATIC DIAGRAM ....... 0.000.000 ccc ccc ese cs eee eeneteee nen ees 28
PRIMARY POWER/FILTER BOARD/ INTERCONNECTION DIAGRAM .......... 0.0.0.0. 0 cc ccccec ec ee eee entree 30
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
LOGIC BOARD ASSY. [A1], COMPONENT LOCATION
LOGIC BOARD ASSY. (A1},
| PARTS LIST | A | 8 | 6 | H | J | K |
+
| XTAL4I | RI | ae | Oo | {+ | Oo |
MISCELLANEOUS ELECTRONIC Le R42 ‘COMPONENTS
| REFERENCE | DESCRIPTION | PART | ||
| NO. | oo | oo | ||
| Bat.1 | Battery, 36V | xO-458 | ||
| cree | Capacttor.01 UF SOV AX.CR._X0-230 | pe} | poe | pw) |
+80%-20%
| C25 | ‘Capacitor, 100 UF, 25V EL-AX | xXO-212 | —- | — | = | oe |
| 26 | Capacitor, 01 UF 50V AX CR, | XO-230 | ||||
| +80%-20% | . | Lo | HS | 3 | 5 _K3_| | |
| C27 | Capacitor, 100 UF, 25V EL-AX | XO-212 | . | pow | Ps) | . |
| 31-34 | Capacitor. 0.1 UF, SOV AX.CR, | XO-230 | ||||
| ra0%. 20% | = | —s | = |
CsI Capacitor, 100 PF, i00V CMD 5% XO-198 cs2 Capacitor, 01 UF. 100V CMD 5% | XO-I96
| C53 | Capacitor. 10 UF, 25V AX. TANT. XO-127 | « | . | . |
| 10% | a | 2 | . |
ALL UNMARKED (CAPACITORS O1 UF, SOV AX CR. +80%-20% = XO-229
| ALL POLARIZED | £05) | } | |||||||
| UNMARKED | ° | . | bd | ||||||
| CAPACITORS | 10 UF, 25V AX. TANT. 10% | xO-127 | R741 | $ | |||||
| D2 | Diode, 1N4454 | XO-275 | |||||||
| D4 | Diode, 1N4733A | XO-274 | |||||||
| ar | Transistor, MPS-U45 | XO-306 | co | K6 | |||||
| 02-04 | Transistor, 2N6044* | xO-120 | co | 7 | |||||
| 81-087 | Transistor, MPSA70 | XO-309 | |||||||
| BiRIG | Resistit, 420; OHM, Si: Atl | X0°35: | 2 G7 | | pH? | | |||||
| R25 | Resistor, IK OHM, 5% 14\/ | XO-5, | e | e | e | e | |||
| R31 | Resistor, IOK OHM, 5% \4\W/ | XO-18 | |||||||
| R32-R34 | Resistor, IK OHM, 5% 14 | XO-5 | = | ||||||
| R37, R38 | Resistor, 330 OHM, 5% Y\W/ | XO-34 | |||||||
| 139 | Resistor, 130 OHM, $86 AW | XOAI72 | f | ||||||
| R40 | Resistor, 270 OHM, 5% /4W | xO-68 | ° | . | ° | . | |||
| R41, R42 | Resistor, 510 OHM, 5% “AW | XO-25 | — | idl | _—7 | ||||
| R43 | Resistor, 130 OHM, 5% 4W | XO-172 | |||||||
| R44, RAS | Resistor, IK OHM, 5% 14W | xO-5 | Lo_] | Ar) | |||||
| R53, RS4, RS6 | Resistor, 1K OHM, 5% WW | XO-S | o | R794 | |||||
| RS7, R5B | Resistor. 560 OHM, 5% A\W/ | XO-36 | — | ||||||
| R59-R6} | Resistor, 1K OHM, 5% '4\W | xO-5 | |||||||
| IRA | | ROMs | KOE | <0] | ||||||
| R70 | Resistor, IK OHM, 5% '4W | xO-5, | e | ¢ | e | e | . | ||
| R73, R74 | Resistor, 1k OHM, 5% '4W | xO-5 | REI | i | |||||
| R76-R80 | Resistor, 1K OHM, 5% '4\W | XxO-5 | a | = | co | ||||
| Ral | Resistor, 820 OHM, 5% W/ | XO-174 | |||||||
| #82 | Resstor 100 OHM, SH 4W — XO-28 | a | ult | cK) | |||||
| R83, REA | Resistor, 15 OHM, 5% 4W | xO-171 | ° | ° | . | . | ° | ||
| RES | Resistor, 80 OHM, 5% AW | xO-24 | — | a | a | ||||
| R86, R87 | Resistor. 15 OHM, 5% “WW | XO-171 | |||||||
| Res | Resistor, 180 OHM, 5% “WW | xO-24 | . | ||||||
| fee. | Resor ISCHMESH WOT | i | pee jy | pe] | pee | ||||
| RO | Resistor, 180 OHM, 5% '4\W | XO-24 | |||||||
| R92 | Resistor. 1K OHM, 5% “AW | xO-S | JP22) | R60 | 7 | ||||
| R93 | Resistor, 2K OHM, 5% “WW | xO | |||||||
| 94 | Reastor IK OHM, 5% UXO | pHs] | cK ] | us | |||||
| R95 | Resistor, 470 OHM, 5% WwW | XO-35 | b | a | ¢ | b | . | ||
| RIG | Resistor, 240 OHM, 5% “W | XO-173, | - | ||||||
| ROT | Resistor, 2K OHM, 5% «W | xOe | YS Q87 | +H | co | R58 | co | LI3-14 | |
| ROB | Resistor, IK OHM, 5% V4\W/ | xXO-5 | 85 -—} | <¥Ds! £2+R92 LFRIO2 | . | ||||
| RID | Resistor. 470 OHM, 5% AW | xO-35, | 84} | Q | ~C+R89 2 RIOOLRIO! | R5I | |||
| R100 | Resistor, 240 OHM, 5% "AW | XO-173 | es 85 | + R83-+R99 RIB * | ° | = | —o-C5] | ||
| RIO} | Resistor. 2K OHM, 5% YA\W/ | xO-4 | 87> | Cy | R86 | R97 | oo | R57 | Re |
| R102 | Resistor, IK OHM, 5% WW | xO-5 | Q85 | XTALSI | <>-c52 | ||||
| RIO3 | Resistor, 470 OHM, 5% ‘AW | XO-35, | 7 | ||||||
| SIP 1, SIP 2, SIP4 — Resistor, Dip, 4.7K, 9 Pin | xO-492 | 5 | |||||||
| SIP 71, SIP 72. | Resistor. Dip. 1K, 9 Pin | xO-493 | = | = | cc |
SIP 73
| X-TAL 41 | Crystal, 15 MHZ | xO-482 | 16 | c_kKie_ | | | | |
| ae | Costa 15 wiz | beet | {pie ) | ine") | pve} | EK} |
| Dip Switch | xXO-505, | co | oo! | |||
| 20 Pin Dip Socket | xO-491 | _—7 |
22 Pin Dip Socket xO-467 BATTERY
| 24 Pin Dip Socket | xO-529 | 7 | HI7 | KI7 | |
| 28 Pin Dip Socket | XO-536 | D | ¢ | . | |
| 40 Pin Dip Socket | XO-530 | — | ee | co | R59 |
FERENCE
A. AIO
812, A OQAESBSRRESLSIBE
AT
G1 G2, 63, HGS LOGIC BOARD ASSY. (A1}, PARTS LIST (CONT.)
INTEGRATED CIRCUITS
| DESCRIPTION | PART | REFERENCE |
No.
| Loghe Board Assy | masse | G7 |
| 8284 CLK Dever | xO473 | GB |
74LS02 Quad 2inpur "NOR" gate xO428 GP
| 7416! Sycrronous 4bit counter | XO.192 | GIO |
| 7415377 Ocal"D" Fp Fp | XO-97 | Gil |
| 8088 CPU | xo490 | Giz, |
741S373 Ocal D-ype fip top XO-445.—GI3, GH, GIS
| 7ALS367 Hex 3state butler” | XO-444_— | Gib, GI7 |
741508 Quod 2-npin "AND" gate XO-85 HI, H2. H3, Ht
| 74HCI38 Decoder/cemultiplerer | XO-190 | HS, H6, |
7ALSI39 Dual | of 4 decoder XO-419 745138 of 8 decoder XON3_H7, HB, H9, HID
| 7415138 1 of 8 decoder | x0437 | HI |
| 7415240 Octal Buterfine drver | XO-91 | IZ |
| 7415373 Ocal D-ype fip op | XO-445 | HI |
| 741285 Octal Bus wansever | —-XO-79 | Hi |
RAM 9 GIIGLP-+ O91
| RAM I GLa | xOIt | HIS |
| ROMA2732A 4K x8 EPROM | —-XO-485 | Hb, HIT |
ROM B2732A4K x8 EPROM XO-485 ROM 9 2764 8K xB EPROM — XO-489— JJ. J3,
| ROM 1 2764 8K xB EPROM | —-XO-49 | 8, J5, 6 |
| ROM 2 2764 8K xB EPROM | — xO409 | J? |
| ROM 3.2764 GK xB EPROM | —-xO489 | 8 |
ROM 4 2764 8K xBEPROM —-xO489 7AUSI39 Dust} of4 Decader—XO4I9 0.
74157 Quad 2onput muivpiexer XO
| 7a1S374 Octal Dive fipfop | X09 | IS |
| 7415244 Octal puferfine dmver | XO? | HIT |
7415157 Quad 2eput mutpiererXO-390
| 7ALS6 Quad input exctusne | XO-435 | KI. K2,K3 |
‘OR gate i
| 7415283 4-01 binary full adcer | X09 | KS |
| 78SI6! Sypenronous presetaple | x04 | Ko |
‘inary counter Ke
| 93419 64 x9 Doar RAM. | x0-99 | 9, KIO. Kil |
| 7415203 4-bi binary full adder | -XO-95 | KZ |
74130 B-nput “NAND™ xO-432
| 4801 kx 8 RAM | x0193 | KB |
| 741245 Ocal Bus Transcener | — XO-79 | KF |
4001 Ik 8 RAM xO193
| 2128 (8G) RAM | xo195 | KIS |
| 2128 (8G) RAM | xo1s | IG |
78186 Quad 2-input exchsive _ XO-435 “OR” gate 7 7415273 6-4 register x0-% 7A1S20 Dual 4aeput "NANO" gate XO-430 L415, 16, 78
| 7415283 4-01 binary ful ger | XO-95 | UO |
| 741532 Quad 2anput “OR” gate | XO-433— | UI |
7ALSO4 Hex verter xo-4i8
| 74SI61 Synchronous presetable | XO-4BB | UZ |
binary counter
| 74186 Quad 2input excise | XO-435 | U3 |
“OR” gate use 7415157 Quad 2ieput mutipleser XO-390 7ALSI61 Smictwonous presettable X40 Diary counter DESCRIPTION
74157 Quad 2-nput mutuplexer 741574 Dual O-ype fp top 745157 Quad 2-nput mutoplexer 7415245 Ocal bus vanscener 7415374 Octal D-npe fp op 741S157 Quad 2input mutipieser 7489 64-2 RAM 7ALSI74 Hex D fp Hop 745189 64-01 RAM 74516} Synchronous presetable binary counter TALSI57 Quod 2-np.t mutupleer 7415260 Dual Sanput "NOR gate 7415298 Quad 2-por register 7815157 Owed 2arpet mubperer 741500 Quad input "NANO" gate 74130 8 input “NAND" gate 74186 Dual 2nput exclsve "OR" gate
74109 4-0 RAM 741508 Hex inverter 741532 Oued 2put “OR” gate 7808 Quad 2nput “AND gate 93422 256 x 2 Dpoler PAM 741802 Quod 2pct “NOR” ote 74184 Dual D-ype tip Nop 7407 Hex btter/arver 741530 8 input "NANO" gate 24161 Synchronous presetable 2415374 Quad O-ype fi fop FCO 2764-3 OK x 8 EPROM FGI 2764-3 8k 8 EPROM G2 2764-3 x x 8 EPROM FG3 2764-3 BK x8 EPROM 7AISIS7 Quad 2input matiptrer 7415260 Dual Sept "NOR" gate 241532 Quad Zit “OR gate 741508 Quod 2nput "AND" ste 74808 Hex inerter 71820 Dual nput “NANO” gate 743161 Synchronous presetable inary counter 7asI66 Bt sit register 741874 Dua tip top 741520 Dual ¢eput “NANO” gate 7ASIe Synchronous presertble Dinar counter 74574 Dual Ope pos. edge ip op. 1009) 74804 Hex verter PART No. Xone xoa34 xO-126 xo-79 x096 0-390 xo8s xO-442 xo-89 0-488
0-390 xO-93 OB 0-390 xO427
x0-432 xO-435
x0-89 xo-418 xO433 x0-404 x0-100 xo-428 xO-434 X0-384 xO-432 xO-488
xo-98 x0-489 0-489 0-489 0-489 0-390 x0.93
0-433 xO-86
x0-400 0-430
xo-488
xo-391 0-434 0-430
x0-440
xo-87
x0-400 hee Aooress aus fos gl,
| Ne Ta | wap | af | |p | para Bus |
| as | Ip | {e484 | ||
| Kio | > pg Spe | Fil | Fiz} | |
| oie | aM | Tela | sconessea $$ 219 | poet |
ae iusto sth —— a
| 2 | ee | we | iz | |||||
| ae Be | ee cae oe SF | i | ||||||
| Reser | a | + | Vest | ‘ | +57 | ww | aay) | gv |
| a | ‘i | s | | | Vee | Vee | ee | | Pm | |
| w98 | ee | oq | . | Bethe | she" | WR vee | WR Vee | WR Vee | ||
| senor | BE | ce | ‘ | =e | Re | |||
| od ae | | | a | ||||||
| jos | He | PROGRAM MEMORY | SCRATCH PAD MEMORY |
see Fe $ 45 06 vanes. et : Bee st
wat a 70 ei/Pe-a Loe oh eRe Elia caves 84 f 24] iNTA His Geisies fs — Se
| AIPT | eho | EE | 88 | |||
| P | SMISESENS | —+ ro payrerse | 20] LOA | CAML | ees | ||
| & | fice | Sone | 3 78 as/§ | 23| 59% | wR | Lt | ig |
| ad | oN | — | ||||
| 8 | qev | tne | a | |||
| i | + | (sourR<€) | RD | |||
| : | oo | a | fee | |||
| ic | 4uusv oe | ay | rol |
ate ———* Csource) wmeEZ 2c} BE2 70 payre-13 Re gages 75 halme-it BE Fb aati a
| 3 | ef | _£0IN neruen |
a2 viet Fa |
| a) | tk xe) | rs | cal | Cy enres | ||
| tseitety | + | 8a | ihe | aps | ||
| - | a | hs | Ee | |||
| & | z | Hesairineata | bs | |||
| Sore | : | far une | 9p | |||
| Ferrin | mf | dole | shi | |||
| ie | t | aiuensettralie | Eo | |||
| ptevef | sip2 | [ee | Jer | Jes’ | a | ke< |
| PVP TT PE TT teteeg | a | fer Tes | Jevea | ee |
yet apes Ai3E $ 3 : ie Fite
| teettESt | ToL a | a} | Ag. | bs vélsa7 |
| ieee | Trea | AP | Hi |
ars zl, BIO &
| Ke | . | z | Bee 38 | |||
| for) | INPUT | a | ‘9 | 176 Set | Lcd | = 20 |
| a | INTERFACE | BoARD | =a | Lon | sin | AULT |
| e | a | LBD, 19 25/4 | SSIS METRS | |||
| ae | ASSY, (OPTIONAL) | coeet | PEE | i | a | it |
¢
| ; | save | eer | “re, alPe |
3 arena) [Aye ne
| 3 | st | ait | oi |
| Fs | os | Ape | BI2 |
° SUFFER iy sf a ER
| ‘i | HA | ae | 3 UMUC sary |
| ze | Baa ps— oat | ‘ita! |
z 4
| g | BS | 0 |
| 3 | o1P SwiTcH | oo |
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
lag PI Le 5 ae az 3 ie +3 th sid tig
x FROM 81-17 «WERT BLANK sv 8 RSSARROMRA Oo
oe ie
BEsK From arose SESE FROM 95-3 « SOSRSELI | 5 2 Feo 06-7 «2888e 1S 5 peu 26-9 + 2SEE_ty 5 Feom 64-3 «WE _t> 6 Pom a4 it Fam 8-5 + HORE EE | 26 FRam 4g-6 4YERT FLOP +, 24 peonaee oH PRORIE! 9 FROM At-g ¢@ ROLL ts 2g
} p=3 p_PS, oh fo spre ESBS Fam aie aw 16 Fh Aipig «HORR_SINELS |g Fearn Atptnige SE2__1s 13 ogee FeoM Aipn26 «222855 17 FROW AD IW 254 OPE 5 15, I +5 meaig B ios =e * S33
DESIGNATIONS P1 THRU PE WEE INDICATED FOR REFERENCE ONLY.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS A A ADDRESS BUS 4 PATA BUS
| ‘ups | cose ued 3 | a | C13, C14, C15, COLOR RAM | a |
ee vib 33
| 5 ten gop ues | Fore ibs THgs Ale, | 289 | ||||||||
| CuK. | Bice ving ht | GA® | fx00 | |||||||
| es | pacing tye | 7 | Py | 78 | ||||||
| co | Back vibe 5|%% | sores +3 | & | |||||||
| aa ir tio | Bick vie] ste | a | ||||||||
| Rceata Tate | 3, | Eom | XO) | |||||||
| als as | Bey, | Reo | ||||||||
| PHS Shree: | WR | mrSA7o | ||||||||
| Saas WE | le | sa | 7 | ol | tose | Rot | ||||
| ie | 5 | Qa | ||||||||
| H5¢He | on | Mesn70 | ||||||||
| Line BUFEER| | 4 | HI¢ | “efor | aa | ||||||
| Bopeecs | -raeo | : | aLeR | pa GIS | le | |||||
| 3 | eaNTER, | Hrawwild (use af | ae | ik) | ig 7489 | $3 | ||||
| LINE. ADDRESS. Sant | Pt | cae | PARALLEL, | 408 | sa | |||||
| ZU MUe | LES las HT” | BAB) | T0,SERU| | SEALY 08 | ||||||
| 39 | oe OG peeve | ad | oo | SES |4% | a | |||||
| 1408 | ae alte | | | ees | : | 5 | Ms | es | Jumper, | 0° we we | gen |
| a | aE) comes | lieeeery 22S | eer ion FOR | Z | mesare | GREEN | |||||
| a | : <i | TELSO2 | SUMMER, | ed |
or ase
| a) | ey | 4 ss | Be | 0 | MP=ATO |
| = | a8 8 A ae | Ey | cS | Bp | |
| cl | ki | a | 12, | i | Ri |
| GB es9 | cares | ate | wae | (P) | Fst |
| DISENARLE | iz wear | Ls | cea | os | GS |
| nr | COUNTER | - | REE hoe | nm | |
| B00NS | rer | puta | Ge | ) | |
| counter | Tre | as | BLUE. |
3 MPSATO
| 4 | fi | RBs | |||
| 08, D9, Dio | 11,012,013 | Panna | |||
| — | 06, | —— | 322 | »I2, | ITAL TOMA IDES GRD |
| . | bes | ws oft | - | ‘ADDRESS BUS |
ogee 7 orem
| Uren | K4 THru KB | RAZ 1a | lat | 2 ato | ora | |
| CATERER acetate eg | FOREGROUND OBJECT ROMA | Be | soe the pags) o fizero. | areas | ||
| we | (| | Hig | e580 S].5 Fis pp fltaene | EMS | ta] | |
| ie | borne 414, | 5 f SER | ras 4]. | ia rd | ||
| 7 | 22e5 3], | be | oTRAG 3 | er | ||
| eit | ae | esrac | | seo | EAs | ||
| Hie] | DMA | peray t | IG RDG | STEAD 73 | | ROL | |
| Us] | rT) | ee | ‘TRANSFER, | rer | LPSEAIO 22 | |
| | “9 | JB orpcenou | aang | he | 07 pO | Conga 13] | |
| T4Ls32 | Rep | BKAS 6 | CRAP 2 yy | ore ot | ry | py eaters |
| x | = | is Gi pte |
I rlsts7
| Hi | E10-11 | clades | Sf Zronoe yf ace vio 2, |
BACKGROUND jee
| ae | 7 | ae | wae? | CHIR | es | yf | bace vos |
| | | BACKERDUND | RAM | RAM | FI | be cing a | ||
| Enneacter | — | si | |||||
| REGISTER, | BOTRWR/OTRAIZ | os fi | |||||
| bene | a | ane | |||||
| CO | ee | esc | ce | ve REAR | oraz ,272, | | 3 | |
| 4 | BRWR 1], DS ypfz BRAD | 10% DIO | ie | —y > | |||
| c | DS | va | 5 | pied | > | ||
| Cooma | a | wt | ‘rater rage | SOE E160 8 | orem 310 | @ | Fy |
| 5 | EI | We s|e | can ERILULS | ure fizaame | nana ii | raste | |
| 6 | 3 | RDi 4] | peta | 15 OFRAND | ing | ||
| KiK2,K3 | ic OTRAT | aa zn, | | |||||
| dedect om | sess | cx 5g fLomae | |||||
| obese LATCHES | ST | sew | A | we | |||
| 7 | wae] | oka. |
n LOGIC BOARD ASSY. (A1), SCHEMATIC DIAGRAM, SHEET 3 OF 3
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
POWER SUPPLY ASSY. (A3), COMPONENT LOCATION Pa 4—t5V DC ( SOURCE) T T = >16 IN4734A
| ot | Di2 | 7 |
mnvoct = pee Bee
| uit—y+ 4+ | bd | Ri |
| Das | R31 | Ww |
tay t zon wa
| p23) | £22 | asw | Mvs752 W | _ |
| 20 vor | — | a | ol | |
| Diz | as, | R18 | ||
| re | 4 | = | - |
SS 8s
| en | 4 | Hs | : |
| 2 | as | HS. TO-3 |
« R22
| Fe | Lek | 2N3055 | 23 |
on 2w
| a | taevoc | out |
é 50V c22 ae
| s2200ur | 025 | D26 |
75V {N4745A Mv5752 16V, 5%
| L | Ww | - |
IN4004 IETS | 2 (______________5
| p32 | 031 | DEY | H | ||||
| 7 | + | 419.sv 0c, | [in| unssor | our | +46V DC(souRCE) | | | - |
| MLP-12 | t | t | |||||
| ose | Rai] | a7ourl. oa | ae | 7 | 1 | +12v be (SOURCE) | iy 4 |
| 933 7500. | 35V | a | Liev | i |
C32 33 [nnn ic 5
| iw | c3l | 4 | ||
| ow | aa | = | i | H |
POWER SUPPLY ASSY. (A3), PARTS LIST MV5752, : 044 IN4004 KEY: 2
| REFERENCE | DESCRIPTION | PARTNO. | REFERENCE | DESCRIPTION | PART NO. | = | ! | |||||||
| Power Supply Assy. | Ma-492 | °2 | Connector, 10 FN | x0531 | LM320 | H | ||||||||
| CM,C32,C42_—— | Capacitor. 01 mid. Sov | XO-229 | 3 | Connector, 7 PIN | XO-526 | ~19.3V DC | IN) MUP- 12 | OUT | =—12v DC (SOURCE)! | |||||
| 2 | ‘Capacitor, ]OOUF. 16V" | XO-235 | 4 | Connector, 16 PIN | xO-372 | aoa | —+>3 | |||||||
| 03.23 | Capacitor, UF, 100V | x0-2% | on | Transistor, PNP. 2N5879 | XO323 | ae | 7500 | -OluF | (rez) U4! | uf | H | |||
| Cis, C33, C43 | Capactor 0.2UF. 16V | x0-205 | az | Transistor, NPN. TP3IB | XO-GAI | a | sv | Loy | = lev | i | ||||
| ai | CCepacior, 22000F, 75 | xO-132 | a2 | Transistor, NPN. 23055 | XO-301 | R4I | Tai | cas | 1 | |||||
| 31. cat | ‘Capacitor, 470UF, 35V | xO-286 | Rn | Resistor, 470 OHM, 5% 1A | XO-55 | c4e | snd | + | ' | - | ||||
| Bi D2s | RI | Resistor 100 OHM. 59% 17 | XO.137 | vas | Law | = | ! | |||||||
| 35, 043 | Diode, Light Emitting MV-5752_ | XO-270 | RIB, RIG | Resistor 12 OHM, 5% 2W/ | XO138 | = | = | NOTE: | j | |||||
| or | Diode, Zener, 5 6V, 5% NW | XO-255 | RIS, | Resistor, 200 OHM, 5% AW | XO-43 | Mv5752 | ALL RESISTORS ARE +5% | ' | ||||||
| INS74A | Rig | Resistor 180 HM. 5% KW | XO-24 | H | 7 | |||||||||
| 02-024 | Drove, INSHO! | x0-263 | R17 | Resistor 100 OHM, 5% KW | XO-28 | = | H | |||||||
| 026 | Diode, Zeer, TEV. 5%, IW, | 0-620 | a | Restor, 20 OHM. 5% YW | 0.29 | eons | ' | |||||||
| tNa74sa | R22 | Resistor, 1 8KOHM, 5% 2W/ | x0135 | ey | ||||||||||
| 031034, 036 | 23 | Restor, OHM. 535 207 | X0-827 | |||||||||||
| DsL.082.084 | Diode, M4004 | x0-254 | 3, Rat | Restor, 750 OHM, 53% IW | xO136 | | | ||||||||
| fi | Fuse, 6 AMP SLO-BLO | ee | scat | Siicon Contoled Rectifier | XOr31 | |||||||||
| Fai | Fuse, 2 AMP SLO-6LO | eL7 | ut | Diode, Programmable Zener 1431 XO-272 | ocr | err | ee | ee | ee | eS | SS | SS | OC | eC |
| 31, #32 | Fuse, AMP SLO-810 | es | ua | Voltage Regulator #12V, UM 340T XO-473, | ||||||||||
| Fal | Fuse, !AMP SLO-BLO | es | ua | Voltage | Reguator-I2V. LM 320. | XO-130 | ||||||||
| A | Connector 4 PN | er | var | Potente 00 OFM | xO | POWER SUPPLY ASSY. (A3), SCHEMATIC DIAGRAM |
24 25 26 -
X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
SOUND BOARD ASSY. (AG), COMPONENT LOCATION
REFERENCE
aa 4-c7, clo C12, €20, C21 23,25, C26 28, 29, C30 C33, C42, Cas 31, ca ar 3, cece oo cs. 45, C46 a7 cri RR, RI2 2, RB RB Rs 223-830 Ra
- ssrdtes wer
28-20887-3 0000 7) O00
SOUND BOARD ASSY. (AG), PARTS LIST
DESCRIPTION
Sound Board Assembly Capacitor, O1UF, 25V
Capacitor, 047UF, 25V (Capacitor 4.7UF, 35 (Capacitor 47UF. SOV (Capacitor. 100PF (Capacitor, 470UF, 35V Capacitor, 33°F (Capacitor. O1UF, 100V Diode, INei48 Resistor, 56K ohm, 5%, 1/4 Resistor, 2K ohm, 5%, 1/4 Potentiometer, 10K ohn Potentiometer, 10K ohm Resistor, 10K chem, 5%, 1/8 Resistor, 68K ohm, 5%, 1/4. PART No. Ma487 xO-288
0-222 xo-291 x0-210 xo-223 x0-284 xO-277 x0-202 x0-261 xo19 xO-18 xo-108 x0:109 xor8 xO-189 REFERENCE
Re? sw u uz U3 us Us-Ub u7 uo uss us ur u20 U2 um 2s. DESCRIPTION
Resistor, OF Switch, Momentary Pushbutton 1c 748 IC, SN7ALs74N (CPU, R6502-13 IC, SN7ALSI38N EPROM, 2732 Ic, su7ais75 IC, SN741S02N RIOT, R6532-18, IC, SNPALSO8N IC, SN7ALS30N Converter, PMI, HOBA-SP IC UMatcP IC. Dual Comparitr, Lwn93 Inverter, 7408 CCostal, 3579545MHZ Socket. 22 Pin DIP Socket. 24 Pin (2) Socket, 40 Pin (2) PART No. O68 xO-5I5 x0-397 xO-434 x0-360 xO-437 x0-485, x0-394
x0-361 xo-18 0-432 x0-416 x0.393 x0-396 x0-402 xO-456 x0-467 x0-529 x0-530 X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
£70 AGP
+5v
+Bhay hile asv eaters |e 25) sie fF 10K 7av 7 | utes) ot. Vv RZ33R25 3830) R27 TOK sa {KOK 10K. > 1 | uie-
| aime | Bo | —- u15-36 |
R26 ABIO.
| 10K | etl | eur, s4h 65 |
= UR U3 LMI93, S502, LAMP DRIVER | “GPU INTERFACE peg
Des DATA BUS
| clock Logie | « | oes | ||
| YI | +0 | GL | 086 | |
| 3.579545 My | 644 | 87 | ||
| 0 | MZ | aur | oT | i. |
al IRQ) a ti : a1 —_ 7a vo ES
| 33eF | sv | 18 |
JUMPER CONNECTIONS
| E16-E17, Maz | : | Rl |
E1G-€18, 2Mqx [Eig bic EIT
| NOTES! | BH pei. | NIL + | FROM E8 |
LLUNLESS OTHERWISE specirien, | p—Zq]ABl2 ABIS = sh6 RESISTORS ARE £5%, 1/4.W. 2, LEGEND WITHIN GATES INDICATES SCHMITT TRIGGER. AWITH THE EXCEPTION OF ELE2,E3 AND E1G,€17, €183 SOLID JUMPERS Used with 2716 PROMS. DASHED JUMPERS USED WITH'2732 PROMS. us
Pfo A@PI AUDIO OUTPUT
wae NESS + EG. ren Sov 1} taupe Lesa Rea. “aTUF T4LS02
REFERENCE
c1,c3
RL R2 RS uL v2 $234, 0.1UF a
i¢o8 DIGITAL To ANALOG |CONVERTER, 45V $18 sg P29 WWE uI6 ai$04 fie DOF
PART
| DESCRIPTION | NUMBER | +5v | ||
| Piggyback Board | Ma-483 | ‘6 | ||
| Capacitor, 0-1UF, | Sov | x0-230 | prof] | EY |
| Capacitor, | 100UF, 25¥ | xo-212 | agi |
Resistor,’220 ohm, 5%, 1/2W X0-185 ts Resistor, 10 ohm, 8%, 1/4" X0-32
| Resistor, 1 ohm, Si,1/2W | X0-593 | ee |
Socket, i4 Pin X0-619
| IC, Lud0o2T or TDaz0027 | ——_X0-550 | eg] |
clip Heat sink 0-528
To U3-6-—+ Aue +5v
20 + Hag mag iA oat AS PAL
Pas 4 yeas Nee PAS 13,8 AGPI-B.
S4, AGP,
$8, APL
Ste, U3
U2, | Lm2oo2T UL (socken) | ‘OR | toa8800r {Ler | AMPLIFIER
Is MA~483 BOARD
SOUND BOARD ASSY. (A6), SCHEMATIC DIAGRAM
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
XI. PARTS INFORMATION
TABLE OF CONTENTS
SPEAKER/MARQUEE ASSY. .
ILLUMINATION ASSY. ............-...0555 34
CONTROL PANEL ASSY. .
SERVICE PANEL ASSY..................... 36
BOTTOM PANEL ASSY. ....
CABINET PARTS...................00 eee 38
CABINET PARTS...............00.-00 200s 39
XI. PARTS INFORMATION
SPEAKER/MARQUEE ASSY. AND ILLUMINATION ASSY.
1 2 3 4 5
6 7 8 9 10
ITEM _— DESCRIPTION PART NO.
| 1 | Ilumination Assy. | MA-376 |
| 2, | Starter | EL69 |
| 3 | Ballast (60 HZ) | EL-70 |
| 4 | Lamp, Fluorescent | lA4 |
| 5. | Cable Assy. | A364 |
| 6. | Speaker Assy. | MA459 |
| 7 | Cable Assy. | MA3I8 |
| 8. | Speaker | EL93 |
| 9. | Speaker Grill | 8-20931 |
| 10. | Marquee, Lexan (Screen) | A-23044 |
XI. PARTS INFORMATION
CONTROL PANEL ASSY.
1 2 3,4
| ITEM | DESCRIPTION | PART NO. |
| L | Control Panel Assy. | MA458 |
| 2. | Joystick (2) | C2297 |
| 3. | ‘Short Button (2) | A-21970 |
| & | Button Holder and Switch (2) | A-21971 |
| 5 | Cable Assy. | MA-464 |
| 6 | Lexan Overlay | A-23045, |
XI. PARTS INFORMATION
SERVICE PANEL ASSY.
eM eWNe a DESCRIPTION
Service Panel Assy. Cable Assy. Switch (Push Button) Switch (Toggle) Volume Control Coin Meter PART NO. M4300 MA-316 EL-57 EL-B5S XO-104 EL-84
XI. PARTS INFORMATION
BOTTOM PANEL ASSY.
vie vf rf La
9 6
| (TEM | DESCRIPTION | PART NO. |
| 1 | Bottom Panel Assy. | MA-375, |
| 2. | Transformer | C-22919 |
| 3. | Capacitor, 50, OOOUF, 25V | XO-141 |
| 4. | Resistor, 200 OHM, 5%, 2W | XO-142 |
| 5. | Fuse, 3 AMP, SLO-BLO | EL-9 |
| 6. | Cable Assy. (Secondary) | MA476, |
| 2, | Fuse, | AMP, SLO-BLO- | EL |
| 8. | Fuse, 10 AMP | EL-23 |
| 9. | Bridge Rectifier {2} | EL42 |
| 10. | Fuse, 2 AMP, SLO-BLO | EL-7 |
| Th | Fuse, 4 AMP, SLO-BLO | EL-33 |
| 12. | Service Outlet | A-18133 |
| 13. | Une Filter | EL-SO |
| 4. | Cable Assy. (Primary) | MA-363 |
ONO MeWNa XI. PARTS INFORMATION
CABINET PARTS
DESCRIPTION
Vent Channel (2) On-Off Switch Switch Plate Cable Assy. Master Electronics Interconnect Cable Back Door Master Electronic Board Rear Door Lock Anchor Plate, Lock PART NO.
D-21754 EL-56 A-223% MA-466 MA-465 D-23073-3 MA-IISS MH4 MH-1 2,3
10. i. 12. 13. 14. 15. 16. 7. 18, DESCRIPTION
Shield, Top Shield, Bottom Monitor Cable Clip Bracket, Shieid Cover Plate, Line Cord Line Cora Cable Assy. High Voltage Interlock Switch Cover, Interlock Switch PART NO.
D-22632 C-22633 A-22620 B-22631 A-21955 B-15357 MA-360 EL-66 A-21888
NOU AWN DESCRIPTION
Left Side CRT Decal Right Side CRT Decal Rear Side CRT Decal Top Glass CRT Frame Monitor Filter Glass Monitor Mask Xi.
PARTS INFORMATION
CABINET PARTS
a
PART NO.
A-23068 A-23069 A-23070 A-22464 A-23042 C-22849-1 D-22463 ITEM
10. 1. 12. 13. 14. DESCRIPTION
Monitor Cable Assy. Front Door Interlock Switch Cover, Interlock Switch 3" Leg Adjuster (2) Lexan Overlay {Screen} Side Decal (Left or Right} Onow
PART NO.
C-22462-3 MA-369 EL-66 A-21888, MH-2I A-23043 D-21346
SERVICE NOTES
wells-Gardner elecTRONICS We TC ORPORATION
19” IN LINE COLOR MONITORS
MODELS 19K4901 19K4906
MODELS
19K4951 19K 4956
wells-Gardner electronics
CORPORATION 2701 NORTH KILDARE AVENUE CHICAGO, ILLINOIS 60639
WARNINGS
- Power Up Warning— An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing or testing is performed since the chassis and the heat sink are directly connected to one side of the AC line which could present a shock hazard. Before servicing is performed, read all the precautions labelled on the CRT and chassis.
2. [RAY RADIATION WARNING NOTICE
- High Voltage— This monitor contains HIGH VOLTAGES derived from power supplies capable of delivering LETHAL quantities of energy. Do not attempt to service until all precautions necessary for working on HIGH VOLTAGE equipment have been observed.
- CRT Handling— Care must be taken not to bump or scratch the picture tube as this may cause the picture tube to implode resulting in personal injury. Shatter proof goggles must be worn when handling the CAT. High voltage must be completely discharged before handling. Do not handle the CRT by the neck.
For replacement purposes, use the same type or specified type of wire and cable, assuring the positioning of the wires is followed (especially for H.V. and power supply circuits). Use of alternative wiring or positioning could result in damage to the monitor or in a shock or fire hazard.
PERFORMANCE AND OPERATING DATA
- Apply a suitable power source to the monitor through an isolation transformer.
- Apply a Suitable signal source to the monitor PCB by means of P201 and P202
- Set Up Controls, All controls are preset at the factory, but may be adjusted to suit program material. 1.0 Supply
Voltage 108 VAC-132 VAC
Frequency 50 Hz-60 Hz
3.0 Service Set-Up Controls MAIN PC BOARD 3.8 Horizontal Width Coil, L352
3.41 3.2 3.3 3.4
3.5
3.6 3.7 Vertical Hold Control, VR301 Vertical Size Control, VR303 Horizontal Held Control, VR351 Vertical Raster Position Adjustment Jumper (3 positions) Horizontal Raster Position Adjustment Jumper (3 positions) Screen Control (Part of H.V. Unit, T352) Focus Control (Part of H.V. Unit, T352) 3.9 Black Level Control, VR201 3.10 Horizontal Video Position Control, (Horizontal Shift) VR352
NECK PC BOARD 3.11 Video Drive Controls, Red VR401 Green VR402 3.12 CRT Cut Off Controls, Red VR403 Green VR404 Blue VR405
SERVICE INSTRUCTIONS
1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished). 2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. 3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. 4.0 FOCUS Adjust the Focus control, located on the HV unit (T352), for maximum over-all definition and fine picture detail. 5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the’ game signal, short TP601 to TP31. Adjust VR351 until. the picture stops.sliding horizontally. Remove the short.
6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. 7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U" or “D". 8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or "L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning too! adjustment. This control must be adjusted slowly. if necessary, until the picture or test pattern attains the correct horizontal proportions. :
DRIVE RED CUTOFF GRN CUTOFF’ BLU CUTOFF
NEG H SYNC NEG V SYNC
HORIZ. WIDTH COIL
HORIZ HOLD BLK LEVEL
A ers
HORIZ VERT VERT VERT HORIZ
CENTERING SIZE HOLD RASTER RASTER SHIFT = SHIFT FIGURE 1
INSTALLATION AND SERVICE INSTRUCTIONS
1.0 DEGAUSSING The monitor is equipped with an automatic degaussing circuit. However, if the CRT shadow mask has become excessively magnetized, it may be necessary to degauss it with a manual coil. Do not switch the coil OFF while the raster shows any effect from the coil.
2.0 COLOR PURITY AND VERTICAL CENTERING ADJUSTMENT 2.1 For best results, it is recommended that the purity adjustment be made in the final monitor location. If the monitor will be moved, perform this adjustment with it facing west or east. The monitor must have been Operating 15 minutes prior to this procedure. 2.2 Set the converger assembly on the CRT neck with the center line (of the Purity Adjustment Magnet) over the gap between grids no. 3 & 4. (See Figures 2 & 6) 2.3. Make certain that the magnetic ring-pairs are in their correct positions before starting procedure. This produces a zero-correction state and helps facilitate adjustments. 2.4 Vertical raster position adjustment jumper must be in position “C" (center). 2.5 Remove the R-G-B signal from the monitor. 2.6 Turn the Green Cut off Control (VR404) on the Neck Board fully CW. (See Fig. 3) 2.7 Turn the Red and Blue Cut off Controls (VR403 & VR405) fully CCW. 2.8 Pull the Deflection Yoke backward so that the Green belt will appear. (See Fig. 4) 2.9 Decrease the horizontal width of the raster, if necessary, in order to be able to see the right and left edges of the raster, 2.10 Move the two Purity Magnets with respect to each other in order to center the raster on the screen and the Green belt on the raster horizontally. 2.11 Push the Deflection Yoke forward gradually and fix it at the place where the Green screen becomes uniform throughout. 2.12 Turn the Cut off and Drive Controls and confirm that each color is uniform. 2.13 If the color is not uniform, re-adjust it moving the Purity Magnets slightly. 2.14 Decrease the vertical size of the raster, if necessary, such that the top and bottom raster edges can be seen. (GRIDS NO. SAND 4)
PURITY ADV. top —— Fi BLUE ‘ADJ. ys view ON REN ADs.
RED/BLUE RED/BLUE ON GREEN 20" 10 O'CLOCK crock
REAR CONCENTRIC viEW CONVERGER ASSY. SHOWN IN ZERO CORRECTION POSITION
PURITY PURITY
goclockKN——”— 8 o'cLock INDIVIDUAL TAB ROTATION FIGURE2
CUTOFF CUTOFF CUTOFF FIGURE 3
NECK BOARD
GREEN BELT
FIGURE 4
2.15 Rotate the Purity Magnets as a pair (without changing the angle of one magnet relative to the other) in order to center the raster on the screen vertically. 2.16 Readjust the raster to the desired vertical size. 2.17 Turn all three cut off controls fully counterciockwise (CCW). Slowly turn up (CW) the Red cutoff control until a Red raster is just barely visible. 2.18 Siowly turn up the Green and Blue cutoff controls such that their associated colors, mixing with the Red, results in a White or Gray raster. 2.19 Confirm that the white or gray color is uniform throughout the Screen. 2.20 Insert a wedge temporarily as shown in Fig. 4 and adjust the anglé of the Deflection Yoke. 3.0 STATIC CONVERGENCE ADJUSTMENT 4-Pole Magnets and 6-Pole Magnets are for static convergence. 3.1. A cross hatch signal should be connected to the monitor. A pair of 4-Pole Convergence Magnets is provided and adjusted to converge the blue and red beams. (See Fig. 6) When the Pole opens to the left and right 45° syrnmetrically, the magnetic field maximizes. Red and blue beams move to the left and right.(See Fig. 5) Variation of the angle between the tabs adjusts the convergence of red and biue vertical lines. When both 4-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of the red and blue horizontal lines is adjusted. A pair of 6-Pole Convergence Magnets is also provided and adjusted to converge the magenta (red + blue) to green beams. (See Fig. 6). When the Pole opens to the left and right 30° symmetrically, the magnetic field is maximized. Red and blue beams both move to the left and right (See Fig. 5). Variation of the opening angle adjusts the convergence of magenta to green vertical lines. When both 6-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of magenta to green horizontal lines is adjusted. 3.2
3.3
3.4
3.5
FIGURE 6 GREEN GUN IS THE CENTER GUN. CONVERGE THE RED AND BLUE. THEN CONVERGE REO AND GLUE ON GREEN.
4-POLE O)
4-POLE MAGNETS VERTICAL CONVERGENCE BLUE & RED
3.2
HORIZONTAL CONVERGENCE BLUE & RED
VERTICAL 6-POLE Va
CONVERGENCE |MAGNETS BLUE & RED ON GREEN
HORIZONTAL 6-POLE CONVERGENCE |MAGNETS BLUE & RED ON GREEN an RED/BLU 35 8
ROTATE BOTH MAGNETIC RINGS TOGETHER
JF ALL LINES ARE NOT CONVERGED AT CENTER 5827 REPEAT 3.2 @ 3.3
FIGURE 5
ANODE CONTACT
L 6 POLE CONVERGENCE MAGNETS. | CONVERGENCE [L r — 4 POLE CONVERGENCE MAGNETS / maGNeT ASS'y ——— PURITY CENTERING MAGNETS
‘ DEFLECTION YOKE ‘\__________— nupger weoGes
4.0 PRECISE ADJUSTMENT OF DYNAMIC CONVERGENCE (See Fig. 7, 8 and 9)
4.2
4.3 Feed a cross hatch signal to the monitor. Insert a wedge temporarily and fix the Deflection Yoke so as to obtain the best circumference convergence (See Fig. 8 and 9)
2)
3)
4)
5)
6)
7) Tilting the angle of the yoke up and down adjusts the crossover of both vertical and horizontal red and blue lines. See Fig. 8 (a) and (b). Tilting the angle of the yoke sideways adjusts the parallel convergence of both horizontal and vertical lines at the edges of the screen. See Fig. 9 (a) and (b) Use three rubber wedges (tapered rubber wedges are used for a purpose). The position of each rubber wedge is shown in Fig. 7. Do NOT force the permanent wedges in. They are to be inserted until they just make contact with the yoke—after the yoke has been positioned. Fix the three permanent rubber wedges with chloroprene rubber adhesive. After the adhesive has dried enough to hold the wedges in place, carefully remove the temporarily installed wedge.
UPPER \ ae
RGB UNDER BGR
Daw TEMPORARILY INSTALLED WEOGE
DEFLECTION YOKE
FIGURE 7
UPPER
“P ZL, CRT SCREEN (a) INSERT RUBBER WEOGE CRT SCREEN ) Insert RUBBER WEDGE
FROM UPPER SIDE FROM LOWER SIDE FIGURE 8
CRT
YC la
CRT SCREEN INSERT RUBBER WEDGE CRT SCREEN *)iNSERT RUBBER WEDGE FROM LEFT SIDE FROM LOWER SIDE FIGURE 9
5.0 WHITE BALANCE
5.1
5.2 5.3
5.4
5.5
5.6
5.7 Refer to Fig. 2 and do the following in subdued light. Ground the R/G/B inputs. Set the R/G drive controls to their mechanical centers. Set the screen and R/G/B cutoff controls to minimum (fully CCW). Connect a jumper wire between TP301 and TP302 (located on the MAIN PCB) Slowly turn up (CW) the screen control until the first colored line becomes just barely visible. That color which has just appeared. is referred to as the “lead” color. Do NOT turn its associated cutoff control—it must remain fully CCW. Connect a DC oscilloscope to the collector of the lead color’s output transistor (Q401, Q402, or Q403) on the Neck PCB at TP47R, TP47G, or TP47B. 5.8
5.9
5.10
5.11 5.12
5.13
5.14 Adjust the black level contro! (VR201) to obtain the waveform shown in Fig. 10. Readjust the screen control such that the colored line is just barely visible. Slowly turn up the two remaining cutoff controls such that their associated colors, mixing with the lead color, results in a white or gray line. Remove the jumper wire. Adjust the Black Level Control for a dim raster. Touch up the two trailing cutoff controls (NOT the lead cutoff control) for best gray uniformity. Adjust the Black Level Control for a bright raster. Adjust the R/G drive controls, if necessary for best neutral white. Repeat steps 5.12 and 5.13 until good tracking of white balance is achieved.
BLANKING PULSES
FIGURE 10 140V
O-voc
Ref. No.
R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 Ratt R214 R215 R216 R217 R218 R219 REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R369 | 203%5602-329 | 680K Ohm, 5%, 1/2W Comp, |
| 203X6500-523 | 30 Ohm, 5%, 1/4W Carbon | R370 | 203x€501-002 | 33K Ohm, 5%, 1/4W Carbon |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide |
| 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203X9101-119 , | 12K Ohm, 5%, 1W Metal Oxide |
| 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R375 | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon |
| 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide |
| 340X2201.934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon |
| 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon |
| '340X2201.934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon |
| 203X6500-540 | 390 Ohm, 5%, 14W Carbon | R380 | 203X6500-865 | 8.2K Ohm, 5%, 1/4W Carbon |
| 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | F383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide |
| 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ofim, 5%, 1/4W Carbon |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204X1700-535 | 150 Ohm, 5%, 15W Metal Oxide |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203x9014-267 | 47 Ohm, 5%, 1W Metal Oxide |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon |
| 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R506 | 203X9104-105 | 15 Ohm, 5%, 2W Metal Oxide |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185 | 220K Ohm, 5%, 1/2W Comp. |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | 4 %R601 | 204X1625-058 | 3.3 Ohm, 5%, 10W WW |
| 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide |
| 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Onm, 5%, 1/2W Carbon |
| 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R201 | 204x2070-072 | 2K Ohm-B Semi-Fixed |
| 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R301 | 204x2070-084 | 5K Ohm-B Semi-Fixed |
| 203X6501.044 | 47K Ohm, 5%, 1/4W Carbon | R303 | 204X2070-055 | 500 Ohm-8 Semi-Fixed |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | VR351 | 204Xx2070-072 | 2k Ohm-B Semi-Fixed |
| 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R352 | 204x2070-072 | 2K Ohm-B Semi-Fixed |
203X6500-863 8.2K Ohm, 5%, 1/2W Comp. 203X6500-863, 8.2K Ohm, 5%, 1/2W Comp. 203X6500-863, 8.2K Ohm, 5%, 1/2W Comp. 203X€500-468 180 Ohm, 5%, 1/4W Carbon 340X2820-934 82 Ohm, 5%, 1/4W Carbon CAPACITORS
| 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | C201 | 203X0014-088 | 1000 uF, 16V, Electrolytic | |
| 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | C202 | 202X7200-064 | 330 pF, 500V, Ceramic | |
| 203X6500-508 | 270 Ohm.5%, 1/4W Carbon | C203 | 202X7200-043 | 220 pF, 500V, Ceramic | |
| 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, 500V, Ceramic | |
| 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C205 | 203X0014-076 | 470 UF, 16V, Electrolytic | |
| 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | C208 | 203X1810-149 | 0.1 uF, 125V Mylar | |
| 203X6500-842 | 6.8K Ohm, 5%, 1/4W Carbon | C207 | 349X2232-109 | 022 UF, 100V Mylar | |
| 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | 301 | 203x0014-065 | 330 uF, 50V Electrolytic | |
| 203X6500-825, | 5.6K Ohm, 5%, 1/4W Carbon | C302 | 203X1600-563 | 0.033 uF, 50V Mylar | |
| 203x6500-965 | 22K Ohm, 5%, 1/4W Carbon | C303 | 203x0629-037 | 3.3 UF, 50V Electrolytic | |
| 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203X1600-366 | 0.068 pF, 50V Mytar | |
| 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C306 | 203x0412-012 | 2.2 uF, 16V Tantal | |
| 203x9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | 307 | 203Xx1600-634 | 0.033 UF, 50V Mylar | |
| 204X 1450-537 | 1K Ohm, 5%, 5W Carbon | C308 | 203X0025-174 | 3.3 uF, 5OV Electrolytic | |
| 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | 309 | 203X1207-100 | 0.068 UF, 100V PP | |
| 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | C310 | 203X0629-061 | 10 uF, 100V Electrolytic | |
| 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | c3tt | 203x0041-025 | 10 uF, 160V Electrolytic | |
| 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | C312 | 202X7050-248, | 1000 pF, 500V Ceramic | |
| 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | 313 | 203X0040-052 | 47 uF, 160V Electrolytic | |
| 203x6500-645, | 1K Ohm, 5%, 1/4W Carbon | cata | 203X1201-265, | 0.033 UF, 200V PP | |
| 203x6501-002 | 33K Ohm, 5%, 1/4W Carbon | C315 | ~~: | 203x0629.023 | 1 uF, 50V Electrolytic |
| 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | 6361 | 203x0629-023 | 1 uF, 50V Electrolytic | |
| 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C352 | 203X06 19-045 | 47 uF, 25V Electrolytic | |
| 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C353 | 203X1190-015, | 0.0082 pF, 50V Mylar-PP | |
| 203X6500-785 | 3.9K Ohm, | 1/4W Carbon | C354 | 203X0619-045 | 47 uF, 25V Electrolytic |
| 203X6501-088 | 68K Ohm, 5%, ¥4W Carbon | C355 | 203X 1600-366 | 0.0068 pF, 50V Mylar | |
| 203X6500-762 | 3.3K Ohm, 5%, 14W Carbon | C356 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| 203x9205-143, | 6.8K Ohm, 5%, 3W Metal Oxide | C359 | 202X8065-606 | 100 pF, 500V Ceramic | |
| 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366 | 0.0033 pF, 500V Ceramic | |
| 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483, | 0.01 uF, 500V Ceramic | |
| 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| 203X9014-645, | 1.8 Ohm, 5%, 1W Metal Oxide | 2*0363 | 203x1270-911 | 8700 pF, 1.5 KV PP | |
| 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | C365 | 203x 1201-265 | 0.33 uF, 200v PP | |
| 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25V Electrolytic | |
| 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202x8065-162 | 6 pF, 500V Ceramic | |
| 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | 368 | 202X7203-032, | 0.01 uF, 50V Ceramic | |
| 203X5602-185 | 330K Ohm. 5%, 1/2W Comp. | C372 | 203X1207-125 | 0.1 uF, 100V PP |
P.C. BOARD LAYOUT
wf INT.FACE Qi to 2 ye a Eel le a 7 Joe ty © 18 ee ll "el J5 ° oe ale ita gts re F ‘s) = 5 — a = Jet at
om 0" B® ye a s=-HOROUT 9
= OD ; . =
AB Mae tag ig a Sat
BOTTOM VIEW
FIGURE 11 MAIN P.C. BOARD
P.C. BOARD LAYOUT
TOP VIEW
BOTTOM VIEW
FIGURE 12 NECK P.C. BOARD
MAIN BOARD (CONT.)
| Ret. No. | Part No. | Description | Ref. No. « | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 380 | 202x7200-087 | 470 uF, 500V Ceramic | 206 | 200X3181-523 | Transistor (NPN) 28C1815GR |
| 4.6501 | 203x1810-149 | 0.1 uF, 125V Mylar | Q207 | 200X3181-523 | Transistor (NPN) 25C1815GR |
| 4 C502 | 202X7050-282 | 100 pF, 500V Ceramic | 208 | 200X3181-523 | Transistor (NPN) 28C1815GR |
| 4.6503 | 202X7810-214 | 2200 pF, 125V Geramic | Q209 | 200X3181-523 | Transistor (NPN) 28C1851GR |
| A.c504 | 202x7810-214 | 2200 pF, 125V Ceramic | 210 | 200X3181-523 | Transistor (NPN) 28C1851GR |
| 505 | 203X0220-075 | 560 uF, 200V Electrolytic | Q301 | 200X3181-523 | Transistor (NPN) 28C1851GR |
| C506 | 203x0040-034 | 22 uF, 160V Electrolytic | Q302 | 200X3207-308 | Transistor (NPN) 28C2073LBGL2 |
| 507 | 203X0041-057 | 47 UF, 160V Electrolytic | 303 | 200X3207-306 | Transistor (NPN) 2SC2073LBGL2 |
| 701 | 203X0019-092 | 1000 UF, 25V Electrolytic | Q351 | 200X3248-217 | Transistor (NPN) 25C2482BK |
| C702 | 203x0634-061 | 10 uF, 100V Electrolytic | 0352 | 200X4589-802 | Transistor (NPN) 2508988 |
| 6703 | 202X7050-248 | 1000 pF, 500V Ceramic | ae | 200X2300-033 | IC HA11423 |
| 1¢501 | 200X2600-183 | IC STR381 |
SEMICONDUCTORS
| 203 | 201X2010-159 | Diode, 1$2076-27 | |||
| D204 | 201X2010-159 | Diode, 182076-27 | TRANSFORMERS & COILS | ||
| 0205 | 201X2010-159 | Diode, 1$2076-27 | test | 201%4710-154 | Goll (BF Choke) |
| 0206 | 201X2010-159 | Diode, 182076-27 | br | Feder | gall mane Size |
| D208 | gorxzo10-168 | Heed | 351 | 202X1300-080 | Transformer, Hor. Drive |
| 0209 | 201X2010-159 | Diode, 182076-27 | Ak 1352 | 200X9720-301 | HV-Unit M-11 |
| D301 | 201X2010-165 | Diode, ISS81 | |||
| 0302 | 201%2010-159 | Diode, 182076-27 | MISCELLANEOUS | ||
| 0303 | 201X2010-159 | Diode, 1S2076-27 | F501 | 204X""120-073 | Fuse, 4 Amp. 125V |
| 0304 | 201X2120-009 | Diode. RH-IV | 3402 | 206%s008-632 | Recep W Wire 3P-M.BG |
| 305 | 201X2120-009 | Diode, RH-IV | P201 | 204X9600-466 | Plug, PWB 3P-J |
| 0408 | 201X2010-159 | Diode, 12076-27 | P202 | 204X9601-477 | Plug, PWB 6P- |
| 40501 | 201X3120-216 | Diode, PM.1AV | 401 | 204X9600-298 | Plug, PWB 4P-B |
| 4.0502 | 201X3120-216 | Diode, RM-1AV | P6501 | 204X9600-249 | Plug, PWB 2P-B |
| 41503 | 201X3120-216 | Diode, RM-1AV | 601 | 204x9600-304 | Plug, PWB 4P.C |
| Ase | 201X3120-216 | Diode, RM-1AV | TH501 | 201X0100-112 | Thermistor |
| 0508 | 201x3120-2'6 | Diode, RM-1AV | |||
| 0506 | 201X3120-216 | Diode, RM-1AV | |||
| D701 | 201x2130.294 | Diode, RU-2V | lity ASSEMBLY PARTS | ||
| 0702 | 201X2120-009 | Diode, RH-1V | A | 88X0138-508 | 19VLTP22 Plx Tube |
| 201 | 200X3181-523 | Transistor (NPN) 25C1815GR | 205X9800-158 | Lateral/Purity Assembly | |
| 0202 | 200X3181-523 | Transistor (NPN) 25C1815GR | A | 20041111201 | Yoke Deflection |
| 0203 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 204X9301-255 | CRT Socket | |
| 204 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 291X5004-262 | Automatic Degaussing Coil Unit | |
| 0208 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| Rao1 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | C401 | 202X7060-269 | 1200 pF, S00V Ceramic | |
| R402 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | ca0z | 202X7050-248 | 1000 pF, 500V Ceramic | |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248 | 1000 pF, 500V Ceramic | |
| aos | 203X6000-728 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 1500 pF, 1.5KV Ceramic | |
| aos | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | 6405 | 202X7080-483 | 0.01 uF, S00V Ceramic | |
| R406 | 203X6000-661 | 820 Ohm, 5% AW Carbon | ||||
| R407 | 203X6000-729 | 470 | Ohm, 5% 1/4W Carbon | |||
| R408 | 203X6000-998 | 270 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | |||
| R409 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | ||||
| R410 | 203x9104.824 | 18K Ohm, 5% 2W MO. Forming | prs | Perna | eee or NEN Secret | |
| Rat | 203X9104-824 | 18K Ohm, 5% 2W M.O. Forming | 0403 | 200X3208-800 | Transistor (NPN) 2SC2068LB | |
| Ratz * | 203X9104-824 | 18K Ohm, 5% 2W M.O. Forming | ||||
| R413 | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | c | ous | ||
| Rata | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | ||||
| Rats | 203X6000-908 | 2.7K Ohm, 5% 1/2W Comp. | sat | wanes ELLANEOU a | ||
| Rate | 203X9105-154 | 2.2 Ohm, 5% 2W Metal Oxide | pe | Patrica | rn | |
| RaI9 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | ; | ug: EWE GPA | ||
| ‘ | P403 | 204X9600-981 | Plug, Pin 1P-D | |||
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | pane | Popes | ae | |
| R421 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | moaXHEOT | 020) | U9. | 7 |
| R401 | 204X2115-014 | 500 Ohm, “B Semi-Fixed | ||||
| vRaoz | 204X2115.014 | 500 Ohm, -B Semi-Fixed | ||||
| VR403 | 204X2115-006 | 5K Ohm, -B Semi-Fixed | ||||
| vRaos | 204X21 15-006 | 5K Ohm. -B Semi-Fixed | ||||
| VR405 | 204X21 15-006 | 5K Ohm, -B Semi-Fixed |
TYPICAL DC VOLTAGES
TRANSISTOR TERMINAL 1.C. 301 No. COLLECTOR BASE EMITTER PIN NO. | VOLTAGE
9.7
9.7 15.4 14.0 15.5
41.4
DO NOT MEASURE OMNOANMSWON=
VOLTAGE
19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956 A Power Supply Voltage and Symbols
| Symbol | vottage | | Operating Circuit | OSCILLOSCOPE WAVEFORM PATTERN | |||||||||
| ® | tev _| vert. Ose | SERVICE TECHNICIAN WARNING | CAUTION: FOR CONTINUED SAFETY. | The waveforms shown are as observed on the wide band | |||||||
| Syne | X-RAY RADIATION PRECAUTION: | REPLACE SAFETY CRITICAL COM | oscilloscope with the monitor turned to a reasonably | ||||||||
| Blanking | PONENTS ONLY WITH MANUFAC- | strong signal and a normal picture. The voltages shown | |||||||||
| CRT Cut-Off | THIS PRODUCT CONTAINS CRITICAL | TURER’S RECOMMENDED PARTS. | F | on each waveform are the approximate peak ampli- | |||||||
| cv | noun oss | ELECTRICAL AND MECHANICAL PARTS | AVERTISSEMENT: | POUR MAINTENIR | tudes. | |||||||
| Ose. | : | LE DEGRE DE SECURITE DE L'APPAREIL | If | the waveforms are observed on the oscill | ith | ||||||
| 0 | Nae ore | ESSENTIAL FOR X-RAY RADIATION | Ra are itt oe ee | tthe waveform | oscilloscope wit | ||||||
| Vert. Output | FOR REPLACEMENT PURPOSES. USE | CRITIQUE POUR LA SECURITE QUE PAR | eerie amin Me pe sh igh trequeney pele vil | ||||||||
| ; | 47 | TYPE | PARTS: | SHOWN, IN. | THE | DES PIECES RECOMMANDEES PAR LE | an | plitu | igh | fr | wi |
| @) | ev | Video output | oats wer | er sHown | iN | FABRICANT. | tend to be less. |
Q351 COLLECTOR 9401 9402 0403 RED OUT -SREENOUT _ BLUE OUT. 28C2068L8/.8K 2SC20681.B/aeK 25C20681 8/.58K' 2scisiaave/cve 28CISIBveeVE 2SCISiaaVC/CVC
| 1VIDIV 200uSECIDIV | 20VIDIV 10uSECIDIV | O.5/DIV SMSECIDIV |
131 D¢ COUPLED : BOTTOM LINE =0 VDC <—_ R204 soaive: > omy jestiove — Se'Biovs Fecsasasc3a6
[RORIVE) [G.DRIVE] [B.cuTOFF) [R.CUTOFF) [6.cUTOFF ome) ee | 9.301 ase sync. AMP = ——
| 2vIDIV 200MSECIDIV | SVIDIV 20uSECIDIV | OSIDIV 20u SEC/DIV | 2scieisy/o. | (EHO) 9 I | e300, | R358 | 0362 | |
| fecsas | leas: (HOLD) | sit | ite | Bee | ||||
| . | 250845 | vase | thin J 8m | i | Gnd Gin | |||
| LC. 901, PINS | F | LC. 301, PIN 15 | nae | Ln | ee | 9351 | — | 280869. |
| St) e728 | eennses) , HORORIVE | Brie | ‘2808988 |
2sceaezek tT casa | 25C26108K eee id
ve on a)
| LIPSE) | (nor | L_[nor] | [sow] |
{Bet} Lose [tore | (prorectow
mes 38K S3725y
| WOW sMSECIOWY | troy 20u secioiv | FE} EE | al aely |
° 64
| ‘TP-82 | TP-31, AC COUPLED | + vane | ae | Cosy | ; | ;: |
pracs[nace\e20e | a ike 2B eat sync amp vose Kose 8" watiazs og
| 20VIDIV SMSECIDIV | 1VIDIV 200uSECIDIV | 2VIDIV 10uSECIDIV |
LC. 201, PIN 13, NEGATIVE SIDE OF €303
ic so AvR istR381
nue ge37 Seo £13 wa
13, 14
| 1VDIV 200uSECIDIV | 2VIDIV SMSECIDIV | AVIV 2MSECIDIV |
K4901D, K4906D, K4951D 5833 DEGAUSSING COIL K49868
- =]
LIMITED WARRANTY
D. Gottlieb & Co. warrants to the initial purchaser of the D. Gottlieb & Co. machine that the items listed in the following schedule as installed and used in the original D. Gottlieb & Co. machine will for the applicable period set forth in the schedule, computed from the initial date of purchase from an authorized D. Gottlieb & Co. distributor, be free of defects in materials and workmanship:
SCHEDULE
GAME ITEM WARRANTY PERIOD
Pinball All Electronic 90 days Printed circuit boards Pinball-Video All Electronic 90 days Printed Circuit Boards Card Cage 90 days Television 30 days Monitor All Electronic 90 days Printed Circuit Boards Television 30 days Monitor This Limited Warranty does not apply to any parts damaged in the course of handling or assembling by the customer or damage due to other than normal use or use in violation of instructions or reasonable practices, or further damaged in return shipment. This Limited Warranty is made only to the original customer, and is and shall be in lieu of all other warranties expressed or implied, and of all other obligations or liabilities on the part of D. Gottlieb & Co. and inno event shall D. Gottlieb & Co. be liable for any anticipated profits, consequential damages, loss of time, or other losses incurred by the customer in connection with the purchase or operation of D. Gottlieb & Co. machines or components thereof. The registration card with each D. Gottlieb & Co, factory-wired machine must be filled in and returned to D. Gottlieb & Co. within ten days after date of purchase for this Limited Warranty to be effective. This Limited Warranty applies only to machines so registered.
THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, -
INCLUDING ANY IMPLIED WARRANTY OF MER- ottlieb
CHANTABILITY OR FITNESS, AND OF ANY OTHER OBLIGATION ON THE PART OF THE SELLERAND AMUSEMENT GAMES D. GOTTLIEB & CO.
Gottlieb
AMUSEMENT GAMES
165 W. Lake Street. Northlake, IL 60164 (312) 562+7400 Telex 72-8463 AColumbia Pictures Industries Company MP™& mel 4
zs, eh yy I
a
te — i