Centipede CO-182-01 Signature Analysis
Centipede (revision 4) (Atari, 1980) · Change Order · 6 pages · 13 sections · original scan
Signature Analysis Guide
to
CENTIPEDE™ Upright
Please disregard signatures and signature test setups printed in blue on Sheet 1, Side B of the Centipede upright schematics, DP-182-01. Instead please use these corrections as a guide for signature analysis.
© 1981 Atari, Inc.
ATARI INC 1265 BORREGAS AVENUE PO. BOX 427 SUNNYVALE, CA 94086 (408) 745-2000 > warner Communications Company
1.
A. 1.
@. Centipede™
Signature Analysis for Centipede™
Table of Contents
1, Set-Up for Signature Analysis
- Checking Address Lines
- Checking Address Decoder 4, Checking ROM and Data Lines
- Checking Horizontal Sync
- Checking Vertical Sync
- Set the CAT Box switches as follows: Set-Up for Signature a. TESTER MODE: SIG Analysis b, TESTER SELF-TEST: OFF c. PULSE MODE: LATCHED
Remove: ° 5 a . : As ind @ The electrical power from the game. f. CLOCK: As indicated © The wiring harness from the game PCB. 6. Power up the game board and the CAT Box. @ The game PCB from the cabinet. @ The MPU chip C2 from the game PCB.
- Checking Address Lines Connect: @ The extender cables to the game PCB A. CAT Box Settings for Address Test and the wiring harness. Probe Trigger IC-Pin Test Pt. @ Pins 37 to 39 on the MPU socket with a Start 2-25 piece of 28 AWG wire. Stop Tq C2-25 @ The CAT Box flex cable to the game PCB Clock TL 2-39 02 test edge connector. B. Signatures Logic Probe Signal Signature Signature Analysis Procedure on IC-Pin Name Should Be Connect the three BNC to E-Z clip cables (sup- C1-12 ABO UUUU plied with the CAT Box) to the SIGNATURE C1-14 ABI 5555 ANALYSIS CONTROL START, STOP, and CLOCK 01-16 AB2 cccc jacks on the CAT Box. C1-18 ABS 7F7F C1-9 AB4 5H21 Attach the three black E-Z clips to a ground loop C17 ABS OAFA on the Centipede™ game PCB. C15 ABB UPFH Attach the CAT Box data probe to the DATA jack ors 487 sere papell jox data probe to the jact B1-12 ABB Hc89 B1-14 ABS 2H70 The colored E-Z clips on the cables will be B1-16 ABI0 HPPO moved about for each group of signatures to be B15 oe 1293 taken. The set-up for each group of signatures is B1-3 AB12 HAP7 located on the schematic sheet near the device C2-23 A13 3096 to be checked. The signatures are located on or C2-24 A14 3827 near the signal point on the schematic. C2-25 A15 755U
Centipede™
3. Checking Address Decoder 4. Checking ROM and Data e@
A. CAT Box Settings for Address Decoder Test Lines
| Probe | Trigger | IC-Pin | Test Pt. | A. CAT Box Settings for ROMO Test (I.C. D1) | |||
| Start | —- | Gos | Probe | Trigger | IC-Pin | Test Pt. | |
| Clock | — | 6239 | 62 | on | _— | pr20 | OMG, |
| Clock | o_o | C239 | 2 |
B. Signatures To obtain stable signatures from ROMO, it may be necessary to install a 1000 pf capacitor
| Logic Probe | Signal | Signature | from K3-11 to ground. | ||
| on IC-Pin | Name | Should Be | |||
| K3-10 | 3097 | B. Signatures | |||
| J3-8 | asta | 3c97 | Logic Probe | Signal | Signature |
| J29 | 51u? | on IC-Pin | Name | Should Be | |
| v0 | p19 | DBO | 5AF2 | ||
| d2-11 | ROM | 5P33 | D1-10 | DBI | 3276 |
| J2-12 | ROMO | 1H32 | 01-11 | DB2 | 48UH |
| Hott | ABH2 | D1-13 | DB3 | P316 | |
| teste | sel | D1-14 | DB4 | PF7A | |
| H3-9 | _ 9550 | D1-15 | DBS | H973 | |
| ne | ; | 9ucé | D1-16 | DB6 | 3F34 |
| Ht | QUAS | 01-17 | DB? | 638 | |
| H3-5 | POKEY | F733 | e@ |
H3-4 4231
| H3-3 | SWRD | 3580 | C. CAT Box Settings for ROM1 Test (I.C. E1) | |||
| H3-2 | Pr | 4PSC | Probe | Trigger | IC-Pin | Test Pt. |
| Ho | RAMO | OOH | Start | “Lh | £1-20 | ROMT |
| J3-11 | F6HP | Stop | J | £120 | ROMT | |
| C58 | FO7A | Clock | TL | 2-39 | 2 |
C46 EA READ oo99 To obtain stable signatures from ROM1, it may
C45 EACONTROL = U08U be necessary to install a 1000 pf capacitor
| C4-4 | EA ADDR | HF7A | from K3-11 to ground. | ||
| E3-3 | INO | 0294 | |||
| K3-12 | 5554 | D. Signatures | |||
| E36 | INT | 40A4 | Logic Probe _ Signal | Signature | |
| E3-8 | PFRAMRD | 4P5C | on IC-Pin | Name | Should Be |
| For the following four tests, ground J2, pin 1: | E1-9 | DBO | 13PH | ||
| J2-7 | PEWAS | 41uU6 | E1-10 | DB1 | Caps |
| 12-6 | PEWRD | 1C3F | E1-11 | DB2 | 11F3 |
| J25 | PFWRT | 4FH7 | E1-13 | DB3 | ogsP |
| J2-4 | FWRO | 461F | E1-14 | DB4 | 5H24 |
| E1-15 | DBS | 0548 | |||
| E1-16 | DB6 | 33P7 | |||
| E1-17 | DB7 | 80AA |
E. CAT Box Settings for Address Decoder Test (LC. FIH1)
| Probe | Trigger | IC-Pin | Test Pt. |
| Start | TL | FIH1-20 | FOMZ |
| Stop | I | F/H1-20 | ROM2 |
| Clock | ~ hl | 2.39 | o2 |
F. Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| FIH1-9 | DBO | CU62 |
| F/H1-10 | DB1 | 9553 |
| F/H1-11 | DB2 | 7756 |
| F/H1-13 | DB3 | A7CF |
| FIH1-14 | DB4 | 6081 |
| FIH1-15 | DBS | SHAC |
| FIH1-16 | DB6 | 6U43 |
| FIH1-17 | DB7 | F83H |
G. CAT Box Settings for ROMS Test (I.C. J1)
| Probe | Trigger | IC-Pin ° Test Pt. |
Start “lL J1-20 ROM
| Stop | J | J1-20 | ROMS |
| Clock | oo | C239 | 2 |
H. Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| J1-9 | DBO | 476H |
| J1-10 | DB1 | 2A2C |
| J1-11 | DB2 | 2337 |
| J1-13 | DB3 | FPO7 |
| J1-14 | DB4 | AQAF |
| J1-15, | DBS | 12HA |
| J1-16 | DB6 | 2367 |
| J1-17 | DB7 | 8P82 |
5. Checking Horizontal Sync (Synchronizer)
A. CAT Box Settings for P2 Counter Test
Probe Trigger IC-Pin
| Start | t_ | P2-11 |
| Stop | S_ | P2-11 |
| Clock | —_ | P22 |
B. Signatures Logic Probe on IC-Pin
P2-15 P2-14 P2-13 P2-12
K4-11 N16 Signal Name Centipede™
Signature Should Be
0102 5SH1 334U 0U16
0102 ACA2
C. CAT Box Settings for N2 Counter Test Probe
Start Stop Clock
D. Signatures Logie Probe on IC-Pin
N2-15 N2-14 N2-13 N2-12 Trigger Hh
Signal Name
8H 16H 32H IC-Pin
N2-11 N2-11 P2-2
Signature Should Be
C3F2 7P25 85PA T7F7
E. CAT Box Settings for M2 Counter Test Probe
Start Stop Clock
F. Signatures Logic Probe on IC-Pin
M2-15, M2-14 N1-10 M3-8
M3-5 M36 M43 M4-15
M4-14 N1-4 4-3 4-2
8-11 D4-8 Trigger
oe
Signal Name
128H
HSYNC HSYNC 256H2D 256HD 256HD aa COLOREN
HBLAN IC-Pin
M2-13 M2-13 P2-2
Signature Should Be
FHSF 4596 cc34 1979
P77U 309C 2633 A829
7UFH H93H A829 7UFH
8304 24U5
Centipede™
6. Checking Vertical Sync (Synchronizer)
A. CAT Box Settings for P3 Counter Test
Probe Trigger IC-Pin
| Start | J | P3-11 |
| Stop | ~L | P3-11 |
| Clock | _J— | P2.2 |
B. Signatures
Logic Probe Signal Signature
on IC-Pin Name Should Be
| P3-15, | - | H7P4 |
| P3-14 | 1v | 3F3U |
| P3-13 | 2v | uucc |
| P3-12 | 4v | 2A42 |
C. CAT Box Settings for N3 Counter Test
| Start | "lL | Ne |
| Stop | 7 | N3-14 |
| Clock | 7 | P22 |
D. Signatures Logic Probe on IC-Pin
N3-14 N3-13 N3-12 P49
P4-10 P4-11 P4-12 N4-10 N4-11 N46 N4-2 N4-3 M4-10 Signal Name
16V 32V 64V
VBLANK Signature Should Be
239F 6U0H U047 F91U
5890 108A FUU7 9H7H
94FP F5U6 PPIF 8F15
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.