Battlezone TM-156 3rd Printing
Battlezone (rev 2) (Atari, 1980) · Technical Manual · 64 pages · 50 sections · original scan

This page is a drawing, shown as the original scan.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on a plate on the outside of the game. &
The same number is also stamped on the chassis of the TV monitor, Regulator/Audio || PCB, Battlezone Analog Vector-Generator PCB, and Battlezone Auxiliary PCB. Please mention this number whenever calling your distributor for service.
GAME SERIAL # IDENTIFICATION TAG
MONITOR
BATTLEZONE AUXILIARY PCB
BATTLEZONE ANALOG REGULATOR/AUDIO II PCB VECTOR-GENERATOR PCB
and Service Manual
Complete with Illustrated Parts Lists
Published by: ATARI INC 1265 Borregas Avenue P. O. Box 427 Sunnyvale, California 94086
Copyright © 1980 by Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Lithographed in the U.S.A. 12J ™
© 4 Werner Communications Company
Table of Contents
Location Setup A, New Parts... 6 cen eyes ce cee cbc ee eee ees B. Game Inspection .. GC. Game Instailation.......
- Line Voltage Selection ... .
- Interlock and Power On/Off Switches D. Self-Test Procedure ................- E. Option Switch Settings
- Bonus Play Feature...
- Coin Mechanism Multipliers . .
- Examples of Option Switch Settings . F. GamePlay ...
- Attract Mode ....
- Ready-to-Play Mode
- PlayMode ..........
- High Score Initial Mode... 6.0.6... cece cee 13 OCHWMOONE RWWA
Maintenance and Repair A. Cleaning... 2.6... ccc cece teen eee B. Fuse Replacement... . C. Opening the Control Panel .
- LED Switch Replacement........
- Control Handle Maintenance and Repair Monitor Removal ..............-00 05 19 Mirror Removal. . Housing Removal!
- Fluorescent Tube Replacemen:
- Speaker Replacement........ G. Printed-Circuit Board Replacement .
- Analog Vector-Generator and Auxiliary PCB Removal .
- Regulator/Audio ll PCB Removal ..............- H. Game Operation... 0.0... 00.0 c cece eee teen eens 24 mmo
Illustrated Parts Lists
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5
Figure 6 Figure 7 Figure 8 Figure 9 Figure 10
Figure 11 Figure 12 Figure 13 Figure 14 Figure 15
Figure 16 Figure 17 Figure 18
Figure 19 Figure 20 Figure 21 Figure 22 Figure 23
Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 List of Illustrations
Overview of Game... 6... cece eee c eee eens 2 Installation Requirements 3 Line Voltage Selection .... 0... 00... ccc eee eee 4 Interlock and Power On/Off Switches .. » 5 Location of Self-Test Switch, Volume Control and Option Switches ..... 6
Self-Test Procedure ....... 6... cee 7 Game Option Settings . 9 Game Price Settings .... 10 Coin Counter Option Settings .............. 002. 12 Opening the Control Panel ......... 00... cece cece cece eee eee 16
Control Handle Maintenance and Repair...................20 ee eee 7 Monitor Removal... ... 2.0.0 cece eect eens Mirror Removal .. 20... 600 e eee ee ee en cc ete nt ee ee nee ee Housing Removal ........... Fluorescent Tube Replacement
Printed-Circuit Board Replacement ...... Power Distribution .......... Signal Distribution
Illustrated Parts Lists: Cabinet-Mounted Assemblies Control Panel Assembly ...... Control Handie Assembly . Fluorescent Lights . . Housing Assembly
Power Supply Assembly for X-Y Games Battlezone™ Auxiliary PCB Assembly ......... Battlezone Analog Vector-Generator PCB Assembly . Regulator/Audio Il PCB Assembly ............ i New Coin Door... 2... n eee 48
lf reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographica! area, as shown in one of the two maps below. Order all parts from the California office.
WEST and CENTRAL U.S.A.
Parts for all Atari Customers. Sales and Service
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103
(Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii (408) 745-2900
a@» From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A.
Sales and Service Only
Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347
(Monday - Friday, 7:30 - 4:00 pm Eastern time)
z From New Jersey (201) 469-5993
Z From anywhere else in this area toll-free (800) 526-3849
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following: 1.) you substitute non-Atari parts in your coin-operated game, or 2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Location Setup
A. New Parts
The Battlezone™ game has five new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ The control handle is a redesign of the Atari gear shifter. It has been strengthened by adding several additional ribs to the interior and exterior of the housing. These ribs keep the assembly properly aligned to assure proper switch contact. Another new feature is the rubber centering bellows; it acts as a centering spring to return the control handle to the center position. The microswitches are now mounted with locknuts for easy replacement.
AAWARNING-SHOCK HAZARD £&
This game is designed to be connected only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!
SIDE WINDOW
ATTRACTION
PANEL SPEAKER
HOUSING
ACCESS PANEL
CENTER VIEWING WINDOW (Fe YER) (FOR PLAYER) MONITOR
INSTRUCTION PANEL
CONTROL HANDLE AUXILIARY PCB
LARGE a .\) ANALOG VECTOR. GENERATOR PCB
REGULATOR) AUDIO tI PCB
POWER ON/OFF SWITCH
POWER SUPPLY COIN aS ce
FOOTSTEP
ATTENTION
Le piedestal doit 6tre installé pour la
The footstep must be installed for cabinet Stability. Without the footstep, this game can tip over onto an aggressive player. Stabilité du cabinet. Sans le piedestal, ce jeu pourrait se renverser sur un joueur enthousiaste.
Figure 1 Overview of Game
e@ Atari's X-Y game circuitry has expanded into two interconnected printed-circuit boards—the Analog Vector-Generator and the Auxiliary PCBs. The circuitry produces more lines on the screen at a faster rate, thus creating a smoother screen image. @ This game includes a newly designed power supply assembly. This power supply has a larger transformer to handle the increased power requirements of the expanded game circuitry. @ Battlezone’s new cabinet design will accept- Atari's new deep-well coin box that holds more coins. @ The cabinet also includes a removable footstep which must be mounted on the front of the game when on location. (You can store the footstep inside the cabinet, however, during transportation.)
These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol: \
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Battlezone Analog Vector-Generator PCB, Auxiliary PCB, Regulator/Audio II PCB and Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, contro! panel and monitor for secure mounting. @ Finally, turn on the game and look at the screen through the player's viewing hole. Check that the radar “screen” is centered in the bright orange-banded round hole of the graphics bezel (the upper cardboard). If it’s misaligned, carefully remove the staples that hold the graphics bezel to the wood mounting. Then shift the bezel until the monitor image is centered in the hole of the bezel.
Cc. Game Installation
e
Figure 2 Installation Requirements
Power 175 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required With footstep: 64 x 842 cm (2514 x 33% in.) Without footstep: 64 x 64 cm (25% x 25% in.) Game Height 190 cm (74% in.)
Figure 3
International Line Voltage Selection
- Line Voltage Selection
The international power supply has 4 colored plugs. Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.
Line Voltage Range Voltage Selection Plug Color
90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access pane! and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.
Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet. @ Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. e@ Ifthe results of the preceding step are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.
SAFETY INTERLOCK SWITCH
POWER ON/OFF SWITCH
Figure 4 Interlock and Power On/Off Switches
BATTLEZONE ANALOG VECTOR-GENERATOR PCB
og
- & OPERATOR OPTION SWITCH
ON aig VOLUME INCREASE: TURN CLOCKWISE SELF-TEST | SWITCH US) | | SELF-TEST SWITCH (EURO- VOLUME CONTROL PEAN'GAMES)
Figure 5 Location of Self-Test Switch, Volume Control
and Option Switches
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game's circuitry and con- Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test pro-
options. trols are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary.
Figure 6 Self-Test Procedure
Results if
Instruction Test Passes
lined in Figure 6.
Results if Test Fails cedure anytime you need to change the game’s
To run the self-test, follow the instructions out-
- Set self-test switch to on position (see Figure 5). After about 3 seconds, the monitor displays the picture below.
CENTER COIN MECH MULTIPLIER (LEFT MECH OF A 2-MECH DOOR)
RIGHT COIN MECH MULTIPLIER
SWITCH TOGGLE 8 SWITCH TOGGLE 1
SWITCH AT P10 (TOP ONE) SWITCH AT M10 (BOTTOM ONE)
DISPLAY OF COMPLETE CHARACTER SET RAM FAILURE is indicated by a sequence of 1 to 10 tones. You will hear a short low tone for each good RAM chip, and a long high tone for a failing RAM chip. The test stops with the first failing RAM-chip pair (example: J2 and H2 are a pair). To restart the sequence, press the reset pushbutton on the Battlezone™ Analog Vector-Generator PCB, or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with the table below. Example: four short low tones followed by a long high tone indicates failure of RAM at location B2.
Long High Tone 1st 2nd
3rd 4th
5th 6th
7th 8th
9th 10th Bad RAM Chip Location J2 H2
A2 Al
B2 BI
c2 ct
D2 DI
ROM/PROM FAILURE is indicated by two columns of numbers on the left side of the screen. The number in the left column indicates the location of the failing ROM/PROM(s). Identity the bad ROM/PROM with the table immediately below. Ignore the hexadecimal numbers in the right column.
Displayed No. Failing ROM BIC3*
A FIH1 v1 Ki uM Ni** NOMWRONAO Failing PROM B/C3*, E3 AS, FIH3
- If ROM or PROM BIC3 is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **If ROM N1 is bad, program will be unable to produce tones in RAM test.
Figure 6
Results if
Instruction Test Passes
Self-Test Procedure, continued
Results if Test Fails
- Activate slam switch, all control As switch activates, you'll hear a low beep. panel switches and As switch deactivates, coin door switches. you'll hear a high When satisfied with beep. test, set self-test switch to off position.
- Sounds Test (Optional) You may test the hardware-generated sounds by starting a game and proceeding as follows: Engine Rumble (Idle): Should be heard as soon as start button is pushed. Engine Rumble (Active): Pushing both control handles forward should cause an increase in pitch. Releasing control handles MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner of the display. Math-box failure is explained in the Signature Analysis Procedure, on the game schematic Sheet 1, Side B. Identify the failure with the table below. Displayed Letter Failure T Time out error H Data error—high byte L Data error—low byte
You will not hear a low or high beep for the defective switch.
should cause engine rumble to return to idle. Loud Shot: Press the fire button. Loud Explosion: Heard when you get hit, indicated by cracked windshield. Soft Explosion: Is heard when you hit an enemy tank or another object.
E. Option Switch Settings
- Bonus Play Feature Battlezone™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.
For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 3 plays for $1.00. This bonus feature encourages players to inseri more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).
- Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.
The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.
[2s¢ [s1 [se) |f2se} |]s1
This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/250/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)
You can set these multipliers with toggles 3 thru 5 on the Battlezone PCB switch assembly at location P10. For exact settings of these toggles, refer to Figure 8.
- Examples of Option Switch
Settings
Figure 8 explains the options, giving fourteen examples of the most common U.S. situations. The toggles mentioned are all in the switch at location P10; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$” symbois indicating Atari’s recommendations.
Figure 7 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Battlezone Analog Vector-Generator PCB is mounted in place. When changing the options, verify proper results on the TV Monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the TV monitor screen during the self-test.
Toggle Settings of &Toggle Switch on Battlezone PCB (at M10) (BOTTOM switch when PCB is in game) 8 7 6 5 4 3 2 1 Option
On
Off Off
Off On Off Off
On On On Off
On On
On Game starts with 2 tanks Off Game starts with 3 tanks § On Game starts with 4 tanks Off Game starts with 5 tanks Missile appears after 5,000 points Missile appears after 10,000 points $ Missile appears after 20,000 points Missile appears after 30,000 points No bonus tank Bonus tank at 15,000 and 100,000 points $ Bonus tank at 25,000 and 100,000 points Bonus tank at 50,000 and 100,000 points English language $ French language German language Spanish language
The white block below contains the manufacturer’s suggested settings. All numbers 1 thru 8 are Figure 8 Game Price Settings
toggle settings on the 8-toggle switch at location P10, on the Battlezone™ Analog Vector-Generator PCB (the TOP switch assembly).
50¢ PER PLAY:
Bonus
| No bonus | $1.00 = 3 plays | $1.00 = 3 plays | |||||||||
| 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 |
| Straight | On On On On | On Off Off On | On On Off On |
25¢ Door
| oe) 4 | 3 | 2 | 1 | iC) 4 | 3 | 2 | 1 | @ 4 | 3 | 2 | 1 | |
| On On Off Off | On On Off Off | On On Off Off | ||||||||||
| 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 | |
| 250/$1.00 | On on on On | |@)on of of on | |G@on on off On | |||||||||
| Door or | © | © | ||||||||||
| 25¢/25¢/$1.00 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 |
| Door | On Off Off Off | On Off Off Off | On Off Off Off |
25¢ PER PLAY:
Bonus Bonus
| No bonus | $.50 = 3 plays | $1.00 = 5 plays | |||||||||
| 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 |
| Straight | On On On On | On On Off On | On Off On On |
25¢ Door
| ® 4 | 3 | 2 | 1 | @ 4 | 3 | 2 | 1 | @ 4 | 3 | 2 | 1 |
| On On Off On | On On Off On | On On Off On | |||||||||
| 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 | 8 | 7 | 6 | 5 |
| 25¢/$1.00 | On On On On | On On Off On | On Off On On |
Door or
| 25¢/25¢/$1.00 @ 4 | 3 | 2 | 1 | i) 4 | 3 | 2 | 1 | @ 4 | 3 | 2 | 1 |
| Door | On Off. Off On | On Off Off On | On Off Off. On |
Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on opposite page).
For your information, we have detined below the switch settings for those options reiating to game price, coin mechanism Figure 8 Game Price Settings, continued
multipliers, and bonus play. This information is useful in case you need to temporarily set the Battlezone™ game on free play. or if you have German coin mechanisms in your door.
Toggle Settings of 8-Toggle Switch on Battlezone PCB (at P10). TOP switch when PCB is in game 5 4 3 2 1 Option
Off Off
Off
On On On On Off
Off On
Off Off
On On On Off
On Off
Off
On
Off Free play 1 coin” for 2 plays 1 coin for 1 play 2coins* for 1 play $ Right coinmech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Center coinmech x 1 $ Center coin mech x 2 (Both these settings affect the left mech in a 2-mech door) No bonus coins For every 2 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins” inserted, game logic adds 2 more coins* $ For every 5 coins” inserted, game logic adds 1 more coin*
“in the U.S., a “coin” is defined as 25%. In Germany a “'coin" is 1 DM.
$ Manufacturer's suggested settings To achieve bonus plays, ail coins must be inserted before pushing Start button.
oe \, @@ 2 coins = 1 play
e A.” @ 1 coin = 1 play ATARI
KO @ @ 2 coins = 1 play ATARI
= 3 plays 6000 4 coin
nO @@ 2coins
A” @@@ 3 coins @0@ @ 4 coins
°e 06 2 coins = 1 play A @ $1 coin =3 plays (Susan B. Anthony coin)
O71 @ 1 coin = 1 play Arak’ 2 play minimum (2 coins = 2 plays)
J, oe appropriate phrase) ATARI
Figure 9 Coin Counter Option Settings [These toggles determine which coin mechanisms activate which counters]
For Games Having These Coin Doors: Option
Thai 1 Bahi/1 Baht, German 1 DM/1 DM, U.S. 25¢/- 25¢, Belgian or French 5 Fr/5 Fr, Swiss or French 1 Frit Fr, U.S. 25%/25¢/25¢, Japanese Y100/Y100, Swedish 1 Kr/1 Kr, U.K. 10 P/10 P, Australian 20¢/-
German 2 DM/1 DM, German 1 DM/5 DM, U.S. 25¢/- All 3 coin mechanisms are same denomination; all register on one coin counter.
Left and center mechanisms are same denomination; Toggle Settings of 4-Toggle Switch on Game PCB (at L11) 4 3 2 1
On On
206, or Italian 100 1/100 L.
Off On
25¢/$1, or U.S. 25¢/$1.
On Off uration.
Off Off German 1 DM/2 DM/5 DM. No coin door is currently designed for this contigright mech is another denomination. Requires two coin counters.
Left mech is one denomination; center and right mech are another denomination. Requires two coin counters.
Left, center and right mechs are 3 different denominations. Requires three coin counters.
F. Game Play
Atari’s Battlezone™ is a one-player game with an X-Y or vector-generation monitor. The game depicts a first-person view from inside a tank. The battles are fought in a large valley that is completely surrounded by mountains and volcanos. The valley floor contains pyramids and boxes that can provide temporary protection for players. (These cannot be destroyed by shots.)
The enemy consists of slow and fast “super” tanks and intelligent missiles—all of which become more evasive as the game progresses. In addition, flying saucers appear periodically. These don’t shoot at players, but players can get very high point scores for shooting them.
The Battlezone game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled and the high score initials are reset.
- Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test.
In this mode, the monitor displays three possible pictures. One is a simulation of a typical game, another is the high score table, and the third picture shows the Battlezone logo rolling up from the bottom of the screen.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a game. It ends when the start pushbutton is pressed. When this mode begins, the message PUSH START flashes in the center of the
screen, and the start button will also flash on and off. The sequence of displayed pictures are otherwise the same as those shown in the attract mode.
- Play Mode The play mode begins when the start pushbutton is pressed. The start LED will then stay on, and the audio will begin. The mode ends when the player's last tank of the game is lost.
The game starts with the slow tank visible on the screen. The player can determine the position of either type of tank or the missile by reading the messages in the upper left corner of the screen. For example, ENEMY TO RIGHT may be displayed. In addition, the sweeping radar display shows a dot for the enemy’s location, accompanied by a sonar “blip” sound.
The upper pie-shaped area on the radar represents the player's range of view on the screen below. If the enemy falls anywhere within the radar circle, the message ENEMY IN RANGE is displayed.
Occasionally the flying saucer appears on the screen. It is a harmless observer to the battle and will not destroy the enemy or player. Its position is never shown on the radar, but players can earn 5,000 points for shooting it down. The saucer does act as a distraction, though, since it usually appears at the same time as the enemy tanks or missile. Saucers can be shot down by the player as well as enemy tanks. Scoring for hitting the enemy is as follows: the slow tank earns a player 1,000 points; the missile earns 2,000 points; and the super tank earns 3,000 points. A super tank moves and turns twice as fast as beth the slow tank and the player's tank.
Several options allow operators to set the Battlezone™ game for 2 through 5 tanks, for giving a bonus tank after earning various point scores, and for adjusting difficulty by having the missile appear for the first time at various point scores. For information on how to set your game for these options, refer to Figure 7 in this manual.
- High Score Initial Mode If a player’s score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. The instructions are self-explanatory and are provided in four languages.
Any score on the list over 100,000 points is specially highlighted with a tank symbol following the player’s initials. If a player doesn’t enter his or her initials within about 60 seconds, the game will automatically enter dashes instead. After this, the game reverts to the attract mode.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
nance
and Repair
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the control handle switches, fire button, or start switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the control handle: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.
B. Fuse
Replacement
This game contains five fuses—all on the power supply assembly (not including the monitor fuses).
C. Opening the Control Panel
Prior to repairing or replacing any switch on the control panel, unplug the game. Then open the coin door.
Reach through the opening and remove all three sets of carriage bolts, wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 10). Lift up on the control panel and tilt it towards you.
- LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
To remove LED switch: @ Remove all wires from the faulty switch. @ Tur the switch counterclockwise (as viewed from inside of control panel) while hoiding the black cone-shaped nut on the outside of the control panel. ® = Instail a new switch using the reverse procedure. @ Reconnect the harness wires.
NORMALLY CLOSED (N.C.) CONTACT
NORMALLY OPEN (N.O.) CONTACT
\ LIGHT-EMITTING-DIODE COMMON ° (L.E.D.) CONTACTS CONTACT
Figure 10 Opening the Control Panel
TO REPLACE THE BELLOWS:
Open the housing. Remove both halves of plastic control handle from shaft assembly. If you are replacing bellows in right-hand handle (one with switch), remove tie-wrap at lower end of fireswitch wires. Pull sleeving down until it touches connectors at bottom. Hold three wires tightly against shaft, and slide bellows off the bottom of shaft. Slide new bellows up over the wires and shaft. Then slide sleeving back up over the wires. Leave about 3 inches of sleeving on wires beyond small side hole in shaft. Attach new tie-wrap as shown. Joe Sie = =
LUBRICATE HERE &
BELLOWS
SWITCH ACTUATOR PIN
LUBRICATE HERE
Figure 11 Control Handle Maintenance and Repair
- Remove the wires from the suspected switch.
- Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter.
- Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement).
- Check contacts (push and release the switch button) for closed and open continuity.
- If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
a
- Control Handle Maintenance and
Repair
Normal maintenance involves jubricating three parts in the control handle approximately every six months (this requires removing the controls). First open the control panel as described in Figure 10. Then unplug the “quick-disconnect” connectors on the four control switches, as well as the three connectors for the fire switch.
From the inside of the control panel, remove the four flat and lock washers and four screws that mount the control onto the wood support and the round bezel.
Then open up the control handle assembly by removing the six split lock washers and screws (see Figure 11). In addition, remove the two switches and carefully save the small actuator pins.
For lubrication, use only Dow Corning #111 heavy silicone lubricant (Atari part no. 78-1710). Lubricate the following two parts inside the control: @ The spherical part of the shaft and the two small pivot pins that protrude from this area, and @ The two clear plastic actuator pins, located over the switches (push the narrow ends of the pins into the tube to cover them with lubricant).
Reassemble the control handle, and then reinstall it in the control panel. Reconnect the harness wires as shown in the following diagram: make sure the right colors go to each switch.
YELLOW WHITE
Repairs on the control handle would probably only involve replacement of switches. When removing a switch, be careful not to lose the small clear plastic actuator pins that sit above the white switch actuators. Note: the flat head of the pin must always face towards the switch actuator.
D. Monitor Removal
If you should need to remove the Quadrascan X-Y monitor, follow steps 1 thru 6 as listed on this page. Refer to Figure 12.
- Unplug the harness connector underneath the monitor. Be sure the game is unplugged from its wall outlet!
- Remove the two sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the chassis. (This hardware is located at the left and right side of the monitor, near the access panel opening.) Carefully slide the monitor chassis out the rear of the game. If you must replace the monitor, place the red and green overlays on the face of the new picture tube as follows. Place the red overlay within the top 4 inches of the screen; then butt up the green overlay to the red one. (These overlays may overlap by a maximum of 1/8 inch.) Once the monitor has been installed in the cabinet, check for proper alignment with the graphics bezel as follows. The horizon line (the floor of the valley) should be even with the short horizontal line in the graphics bezel. This line is located between the two screws in the bezel design. Also, the vertical center line of the gunsight should be directly under the D in RADAR (at the top center of the bezel).
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 12 Monitor Removal
Figure 13 Mirror Removal
E. Mirror Removal
If you wish to remove the half-silvered mirror for cleaning or replacement, follow these instructions. Handle the glass mirror with care—it is heavy! Never wipe the silvered side with an abrasive cloth: you will scratch the coating.
Uniock and remove the rear access panei. Unpiug the harness connector located at the left side of the cabinet opening. Remove the two Phillips screws that secure the wood support (located at the mirror’s rear edge): see Figure 13. Carefully slide the wood support and the mirror out of the cabinet. Note that the wood is NOT attached to the mirror!
When replacing the mirror in the game, be sure the silvered side is facing downwards towards the iower froni of tne game. if you see doubie monitor images when looking through the player's viewing window, the mirror has been installed incorrectly.
F. Housing Removal
If you wish to replace the fluorescent tube, either speaker or any of the acrylic panels, you will need to remove the front housing from the game. Follow the illustration in Figure 14. Remove the three Allen-head screws and split lock washers at the top of the game, as well the three at the bottom of the housing. They secure the housing to the cabinet. Tilt the top of the housing towards you, then unplug the harness connector for the speakers. Remove the housing and lay it on a clean surface, with its inside facing up. You can now service any parts in the housing, as well as replace either fluorescent tube. You'll find a list of housing replacement parts in Figure 23.
When reinstalling the housing on the game, be sure the inside surfaces of the three windows are clean. The acrylic windows tend to attract dust more easily than glass.
Figure 14 Housing Removal and Speaker Replacement
- Fluorescent Tube Replacement
To replace the white fluorescent or blacklight tube behind the front graphics attraction panel, follow this procedure (see Figure 15):
- Remove the housing as described previously. Unplug the harness connectors for both fluorescent tubes. To replace the blacklight tube, remove the two screws that secure the light board to the cabinet, and slide out the whole assembly.
Figure 15
- Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you.
- Replace with a new tube. Do not snap the tube in vigorously— you may break it, causing an implosion!
- Reconnect the Y-shaped connectors. Reinstall the fluorescent light assembly with the two screws (if you removed it). Reconnect the harness connectors, and replace the housing on the front of the game.
- Speaker Replacement First disconnect the harness plugs for the defective speaker. Then remove the four screws that hold the speaker in the wood mounting block (the wood block and speaker grille remain attached to the housing with rivets). Replace the speaker, then reconnect the harness connectors.
Fluorescent Tube Replacement
REGULATOR! AUDIO Ii PCB BATTLEZONE 7 AUXILIARY PCB
“>
BATTLEZONE ANALOG VECTOR: GENERATOR PCB
Figure 16 Printed-Circuit Board Replacement
G.
Printed-Circuit Board Replace
Board Replacement
You may wish to remove the Battlezone™ Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB, or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 16 and pro-
A ceed as follows:
- Analog Vector-Generator and
Auxiliary PCB Removal
Unlock and open the access panel. Unplug the 24-pin PCB interconnector from the Auxiliary PCB or the Analog Vector-Generator PCB (whichever board you are removing). Remove the 44-pin edge connector from the right side of the PCB. Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove this screw. Remove the PCB from the cabinet by pulling it out of the plastic PCB retainer. Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, So if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially
Regulator/Audio Il PCB Removal Untock and open the access panel. Remove the five plug-in connectors. Note that all of these connectors are also keyed for proper orientation. Locate the four Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these four screws and the fiber washers behind the board. Remove the PCB from the interior wall of the cabinet.
H. Game Operation
With this manual you received three large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. The diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Battlezone™ is a microprocessor-controlled game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch inputs from the control panel and coin door. These inputs are then processed by the Analog Vector-Generator PCB and output to the monitor, Regulator/Audio || PCB, and control panel.
The monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. The Regulator/Audio 11 PCB performs two functions: 1) it regulates the voltages from the power
supply to +5 VDC and + 12 VDG, and 2) it amplities ea
the audio output from the Auxiliary PCB.
Specifically, the +5 VDC from the Regulator/- Audio || PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCB; +22 VDC is regulated on the Analog Vector-Generator PCB to produce +15 and +5 VDC (the latter for the digital-to-analog converters); and + 22 VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio II PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.
The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.
Figure 17 illustrates the distribution of power in this game. Figure 18 illustrates the distribution of signals. *S
FLUORESCENT & BLACK LIGHTS.
MONITOR
CONTROL PANEL
AUXILIARY PCB 4
COIN DOOR
ANALOG VECTOR- GENERATOR PCB
ON/OFF SWITCH
INTERLOCK SWITCHES
REGULATOR/AUDIO II PCB
LINE VOLTAGE
/__6.1vAc. POWER CORD Z
: POWER SUPPLY
Figure 17 Power Distribution
SPEAKERS
SPEAKER
SPEAKER 1&2 CONTROL PANEL
VOLUME CONTROL
AUXILIARY PCB
COIN DOOR X,Y,Z OUTPUT.
ANALOG VECTOR- AS
GENERATOR PCB
‘SPEAKER 1&2
REGULATORIAUDIO II PCB.
Figure 18 Signal Distribution
Hlustrated
Parts Lists
This chapter provides you with the necessary information for ordering replacement parts for your Battlezone™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
NOTICE TO ALL PERSONS RECEIVING THiS DRAWING CONFIDENTiaL. Reproduction lorodenwitnoul the
Housing Assy.— cara See Figure 23 (Red Overlay) fen leense. no agnt Io reproduce (Ms Graming ts granted 036263.02 036143-01 Fluorescent Lights— Sine bia erat ans ey mien agement (Green Overlay) (Mirror) See Figure 22 sth OF item Rerenysin re
035829-01 (Graphics Bezel)
036124-01 (Black Bezel) A036150-01 { = Auxiliary PCB— (Monitor Assy.) Mn See Figure 25 A 036105-01 036116-01 7 (Retainer Strip) ij (Mirror Support)
Control Handle Assy.— A See Figure 21 Control Panel Assy.— See Figure 20 Se ie 19-9032 or~& (Vol. Control) 71-2110 148001-001 Lock) (Oval Speaker)
036130-01 (rte Sw. Cover) (Speaker Grille) a (Coin Box Bracket) 035745-03 A036247-01 | (10" PCB Retainer, (PCB Interconnector) Q A036189-01 (Inter. Sw. Assy.) 036124-02 034536-02 (Coin Deflector), = (Vibration Damper) Z A021700-01, -02, 03 New Coin Door— (Coin Box) See Figure 28 Te" 030249.01 (Separator) 78-6HO02 : Analog Vect..Gener. PCB— 035745-02 ‘See Figure 26 (18" PCB Retainer) (Rubber Matting) : Rue Reg./Audio Il PCB— 02305010 | See Figure 27 (T-Molding) ~: 009992-01 (On/Off Sw. Cover)
A034631-01 (On/Off Sw. Assy.) : ¥ n036260-01 ; a a (Footstep Assy.) Power Supply Assy.— A036244-01 (Main Harness) See Figure 24 Schematics, Self-Test Label & Manuals— see parts list on opposite page 78-3201 (Cabinet Leg)
Figure 19 Cabinet-Mounted Assemblies A036140-xx Cc (Power Cora)
Figure 19 Cabinet-Mounted Assemblies Parts List
Part No. Description
A021700-01 Coin Box Assembly (for all the same coins) A021700-02 Coin Box Assembly (for two different coin denominations—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations-—has two separators) A034631-01 On/Off Switch Assembly
| A034841-03 | Strain Relief Power Cord | (domestic) |
| A034863-03 | Strain Relief Power Cord | (German) |
A036150-01 Monitor Assembly A036189-01 Interlock Switch Assembly (modified for safety)
| A036244-01 | Main Harness Assembly | (a/so includes on/off switch, 2 interlock switches and their brackets, |
and volume control and its bracket) A036245-01 Fluorescent Light and Speaker Harness Assembly A036247-01 Printed-Circuit-Board Interconnector A036260-01 Footstep Assembly (includes rubber matting) The following six items are the technical information supplements to this manual:
| DP-156-01 | Battlezone™ Schematic Drawings | (Sheet 1) |
DP-156-02 Battlezone Schematic Drawings (Sheet 2)
| DP-156-03 | Battlezone Schematic Drawings | (Sheet 3) |
ST-156 Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for G05-802/805 Quadrascan™ X-Y Monitor TM-156, Battlezone Operation, Maintenance and Service Manual 02-305010 %4-Inch Plastic T-Molding 19-9032 Volume Control
| 71-2110 | Panel Cartridge Lock Mechanism | (for access panel) |
75-07017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-6H002 1/8-Inch Thick Corrugated Rubber Matting for Footstep (14% x 23 5/8 inches are required) 78-24012 &Inch Beaded Nylon Tie Wrap (for PCB Edge Connectors) 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 033266-01 Monitor Mounting “L” Bracket
| 03453603 | Foam Vibration Damper | (for Auxiliary and Analog Vector-Generator PCBs) |
035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer 035829-01 Graphics Bezel 036105-01 Mirror Support 036116-01 Housing Retainer Strip 036124-01 Black Cardboard Monitor Bezel 036124-02 Cardboard Coin Deflector 036130-01 Speaker Grille 036143-01 Mirror 036262-01 Coin Box Bracket 036263-01 Red Monitor Overlay 036263-02 Green Monitor Overlay 148001-001 6 x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
62-039 ——>|
7507054
75-9910W0 ————*
005255-04 Control Handle Assy.— See Figure 21
4 fa fi NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the specific written mermisetn ni, Ine Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any Fight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
78-6900402
Figure 20 Control Panel Assembly A036139-01 B
Parts List
Part No. Description
A036246-01 Control-Panel Harness Assembly 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-07054 Flat Nylon Washer, 0.470-Inch inside diameter x 0.968-Inch outside diameter x 0.075-Inch thick 75-9910W0 #15/32-32 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, 1/8-Inch thick x ¥-Inch wide 005255-04 Control-Handle Bezel 033127-01 Black Molded Switch Bushing 036830-01 Control Panel with Graphics 036102-01 Wood Support Block for Control Handles
035997-01 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbiddgn without ie specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only condittonally. 035995-02 issued, and neither receipt nor possession thereo! confers or transfers any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon. nor ani Tight to reproduce this drawing or any part tnereo! 72-8614 Except for manufacture by vendors of Atari, Inc. ang for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or ‘the subject matter thereof unless by written agreement with of written permission from the corporation.
AD
A036277-01 A036278-01
035995-01
Ad: 1-017 ae 136281-0)
000609-02 7 03628201"
See oe 035792-01 =u ZZ a AOSTK SS: 02,
035844-01 75-944S Ser A087 FS3-5
The A036271-01 assembly has NO fire switch and harness (left control handle). The A036271-02 assembly HAS the fire switch and hamess (right control handle).
Figure 21 Control Handle Assembly A036271-01 and -02 B 7214128
Figure 21 Control Handle Assembly Parts List
S
Part No. Description
A036277-01 Shaft Assembly with Fire Switch Harness (includes pivot ball, pivot shaft and 2 slotted pins) A036278-01 Shaft Assembly without Fire Switch Harness (includes pivot bali, pivot shaft and 2 slotted pins) A036281-01 Centering Bellows 62-043 SPST Pushbutton Switch with Red Non-Lighting Cap (used as fire switch) 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-1412S #4-40 x %-Inch Pan-Head Cross-Recessed Cadmium-Plated Steel Machine Screw 72-8614 #6-32 x 7/8-Inch Hex Socket-Head Steel Machine Screw 73-20809 1/8-Inch Diameter x 9/16-Inch Long Slotted Pin " . 73-a4a¢42/%FX — 3/16-Inch Diameter x Finch Long Slotted Pin <&) 073 42 TB) 75-046 #6 Internal-Tooth Steel Split Lock Washer 75-944S #4-40 Steel Self-Locking Polymer Hex Nut 78-1710 Dow Corning Heavy Silicone Compound #111 Lubricant 85-22F608 #6-32 x ¥2-Inch Pan-Head Cross-Recessed Self-Threading Type F Steel Machine Screw
| 000609-02 | Control Handle Housing | (two of these required per control handle assembly) |
005255-04 Control-Handle Bezel 035792-01 Straight-Pattern Detent 035844-01 Clear Plastic Actuator Pin
| 035995-01 | Plastic Control Handle | (Right Half) |
| 035995-02 | Plastic Control Handle | (Left Half) |
035997-01 Plug for Left Control Handle 036276-01 Bezel for Fire Pushbutton 036279-01 Pivot Ball 036280-01 Piyoi Shaft 036282-01 Flat Actuator Spring 178010-001 Nylon Actuator Ball 178016-001 Spring
Wire Nuts Not Shown for Clarity NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atarl, Inc. Sunnyvale, CA. This drawing 18 only consitionally issued, and neither receipt nor possession Inereot Confers or transfers any fight In,oF license to use, the subject matter of the drawing or any design of technical information ‘shown thereon. nor any fight to reproduce thie drawing of any part thereat. Except for manufacture by vendors cf Alar, Inc. and for manufacture under the corporation's writ: {en license, no right to reproduce this drawing is granted or the subject matter thereof unless by Written agreement with of writter permission from the corporation.
99-11008
035835-01
99-1101
Figure 22 Fluorescent Lights A036146-01 A
Parts List
Part No. Description
A005493-01 Fluorescent Light Harness 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 70-306 18-Inch 15-Watt Blacklight Fluorescent Tube 79-561816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter
99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥2-Inch Clamp (for white tube) 99-11012 1-Inch Clamp (for blacklight tube) 035835-01 Y-Lead Connector
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specilic written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, of license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any ‘aght to reproduce this drawing or any part thereof Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is. Granted or the subject matter thereof unless by written agreement with or written permission from the corporation. A036248-01
036258-01 ™!
036256-01
036152-01
035828-01
Figure 23 Housing Assembly A036147-01
Parts List
Part No. Description
A036248-01 Speaker Harness Assembly 48-004 5-Inch 8&Ohm 5-Watt High-Fidelity Speaker 000869-01 Speaker Grille 035827-01 Attraction Panel with Graphics
035828-01 Instructions Decal 036152-01 Side Window 036256-01 Center Viewing Window 036258-01 Housing
a 034482-02
A035888-01 or -02 (int'l) OR A036354-01 or -02 (U.S)
TOP VIEW (Cr 79-4411006 46-2017002
79-3206
2 WE 03567401 Lf (Int'l only) A035891.01
: & D 78-2708
@ (F2is not used)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally’ issued, and neither 29-053 receipt nor possession thereof confers or transfers any right in, oF license to use, the subject matter of the draw: ing or any design or technical information shown thereon, nor any ‘right to reproduce this drawing or any part thereof, Except for manutacture by vendors of Atan., Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing 1s granted or the subject matter thereof uniess by written agreement with or written permission from the corporation, 78-70501SC
BOTTOM VIEW
3A-MDA3501
A035890-01 (Int'l) A034630-01 or AQ36355-01 (U.S.) A034629-01 79-15021001
Figure 24 Power Supply Assemblies for X-Y Games A035892-01 (International) A | A036353-01 (U.S.) A
Figure 24 Power Supply Assemblies for X-Y Games Parts List
Part No. Description (Reference Designations in Bold)
A034629-01 AS. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 or 02 Transformer Assembly—international only (T1) A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 or -02 Transformer Assembly—U.S. only (11) A036355-01 Power Harness Assembly (U.S. only) 29-053, 26,000 uf 15 V Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR)
| 46-2014001 | 4-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F4, F5, F6) |
| 46-2017002 | 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F1) |
| 46-301203 | 20-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F3) |
78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC. 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 03448202 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction. lorbidden without the specific. welten permission of Alar. Inc, Sunmyvats, Cahforma” This arawing ss only concttionally issued. neither receipt nor possession thereat confers ar vansiers ‘ny right in. licenge fo Use, tne Subject matter 31 (Me Sawing or any design or techalcal information shown hereon. nar any ightTo reproduce this Grawing orany oar! inereot- except tor manulacture by vendors ot Alar, Inco: porated anc for manutactufe under the corporation's wrt fen license. no rght to reoroduce this drawing 1s granted forthe subject matter ihereo! uniess ey writen agreement switn oF written permission Irom the corporation
Gatien
| [036177 | SPARE | Pe | L324 | q | T | Tig! |
car MYL. MYL az ¥ oo
| Qs | ~ | a | a | ||
| S | a | s | |||
| ESET fy | "|e | ae | race, | Yt | a |
S : je
| ideal | ‘ | ' | lo | 23 | Saat? | : | |||
| of | HS | tact | |||||||
| (036179 | SPARES | " | pausieag | Paiste, | |||||
| me see | ca | \ | |||||||
| SE a | i | Is | 3 | ||||||
| 88 | go | ie | : | ' | |||||
| O3e1804 | Jo | [ratsi | 7401619 | al | 7 | ||||
| cis | 137004 | 4 | [seo | aisiel ¢ | ~ | se | & | Im | og |
| ll | ri | R. | iN | ||||||
| Seep | BBR | 5 |
7 “
| rac sie | <> | Tas | 748864 |
C24 SE 9aa
| Qs | a> | daaee | I |
jo
| |37004 | Fi | is) | ||
| T4LSI6I§ | 74.502 | 74508: | UW | os |
geass S8Se00
| 74153744 | T4USi856 | Task | rans74s, | ioe see] |
corz294¢-01 qpcas ay GEIR 36 '
| ; | Sane | Tao, | = | [Brae |
G os | 4 ce lo D> QD 2S S|
| ‘ | 8 | eet | {9 |
| SPARE | SPARE | ts |
pan a ISIoIoLeolelorelere slererolsiorarerereiers] Ma! is
| 0 | cis | cz | {lo} |
| a | ea | 10) |
Figure 25 Battlezone™ Auxiliary PCB Assembly A035678-01 B
Figure 25 Battlezone™ Auxiliary PCB Assembly Paris Lisi “~S
Part No. Description (Reference Designations and Locations in Bold)
C012294-01 Audio I/O N-Channel MOS/LSI Custom Chip (B/C2) 21-101153 .015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C11, C25) 21-101472 .0047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C21, 22) 21-101474 -47 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C29) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13, 14) 24-250227 220 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C27) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C28) 24-500475 4.7 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C9) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 10, 12, 15-20, 23, 24, 26, 30-35) 31-1N914 75V Type-1N914 Switching Diode (CR1) 37-LM324 Type LM324 Integrated Circuit (K5, M5) 37-4066 Type 4066 Analog Switch Integrated Circuit (J3, L4)
37-555 Type 555 Timer Integrated Circuit (F3) 37-74LS00 Type 74LS00 Integrated Circuit (D3) 37-74LS02 Type 74LS02 Integrated Circuit (D4) 37-74LS04 Type 74LS04 Integrated Circuit (4)
37-74LS20 Type 74LS20 Integrated Circuit (J4) 37-74LS32 Type 74LS32 Integrated Circuit (C4) 37-74LS74 Type 74LS74 Integrated Circuit (C5, J5) 37-74LS139 Type 74LS139 Integrated Circuit (C3)
37-74LS161 Type 74LS161 Integrated Circuit (D1, E1, F4, F5) 37-74LS164 Type 74LS164 Integrated Circuit (H4, H5) 37-74LS273 Type 74LS273 Integrated Circuit (M2) 37-74LS374 Type 74LS374 Integrated Circuit (C1) 37-74S08 Type 74808 Integrated Circuit (D5) 37-74109 Type 74109 Integrated Circuit (B4) 38-MV5053. Type MV5053 Red Light-Emitting Diode (CR2) 79-42C16 16-Contact Medium-Insertion-Force Integrated Circuit Socket (B1, F1, H1, J1, K1, L1, M1) 79-42C40 40-Contact Medium-insertion-Force Integrated Circuit Socket (B/C2, D/E2, F2, H/J2, K2) 020670-01 Test Point 036174-01 Programmable Read-Only Memory (B1) 036175-01 Programmable Read-Only Memory (M1) 036176-01 Programmable Read-Only Memory (L1) 036177-01 Programmable Read-Only Memory (K1) 036178-01 Programmable Read-Only Memory (J1) 036179-01 Programmable Read-Only Memory (H1) 036180-01 Programmable Read-Only Memory (F1) 110000-102 1K Ohm, + 5%, YW Resistor (R2, 3, 5, 7, 15, 16, 22, 38, 46-52) 110000-103. 10K Ohm, + 5%, %4W Resistor (R13, 18, 30, 36) 110000-124 120K Ohm, + 5%, YW Resistor (R11)
[Continued on next page]
aRK Figure 25 Battlezone™ Auxiliary PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 110000-104 | 100K Ohm, + 5%, %W Resistor | (R8, 10, 23-25, 28, 31) |
| 110000-151 | 150 Ohm, + 5%, %4W Resistor | (R37, 45) |
| 110000-223 | 22K Ohm, + 5%, YW Resistor | (R9, 14, 17, 29) |
| 110000-333 | 33K Ohm, + 5%, ¥4W Resistor | (R12, 19-21, 26, 34, 35) |
110000-334 330K Ohm, + 5%, %W Resistor (R27, 32, 33) 110000-471 470 Ohm, + 5%, %W Resistor (R1, 39-44)
| 110000-472 | 4.7K Ohm, + 5%, V4W Resistor | (R6) |
| 137002-001 | Type 74886 Integrated Circuit | (E5) |
| 137003-001 | Type 74803 Integrated Circuit | (E3) |
137004-001 Transistor Array (D/E2, F2, H/J2, K2) 179014-012 12-Pin PCB Header
rT A . @ se = ; Peacae aaa ft atbeedads = vo gt oe oe Ss B Nanoangs ese cess (ee. = ES of; ereaoe Casas pasoat, ;: favre’ fasee — [racsone azaze SERENE RG E.. ry os EE cae Se ti
1 = si ve ee er ee eae Le pase? raced aman fe? amet 7 enema err ie ery eer ee
a Vea] [95]
- nom el ATT ; balled
Pasex rash pasar) fasirs¢ pecs fine} con [escaun ma RPE See i ge
fo fam «= CES mea i0''o j = Bo CD Le as Sow [eres facies? = facsaad faced ees fl oy
se Sat ae panos : faced = fsscol« fsfracarsd fuel * ewes 5 cad 8 ag Re By an = Ber
A036424 -02 Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly
Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly Parts List
Memory Components (Locations Shown in Bold)
-02 P.C. Boards (ROMs)
036409-01 (N1) 036410-01 (UM1) 036411-01 (K1) 036412-01 (1) 036413-01 (FIH1) 036414-02 (E1)
036421-01 (A3) 036422-01 (BIC3)
Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List
of the Battlezone memory chips (described on the previous page) PLUS the Universal Vector-Generator PCB. The latter is interchangeable with Battlezone and future X-Y games, but not with Lunar Lander™ or Asteroids™. All the following parts in this figure make up the Universal Vector-Generator PCB Assembly.
Part No. Description (Reference Designations and Locations in Bold)
Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts:
19-007
19-315103 19-315201 21-101102
21-101103 21-101473 24-250106 24-250107
24-500105 27-102182
28-101100 28-101101
28-101151 28-101221 28-101390 28-101470
29-006 29-088
31-1N100 31-1N914
33-2N3906 34-2N3904 34-2N6044 37-LM319
37-TLO82CP 37-13201 37-347 37-74LS00
37-74LS02 37-74LS08 37-74LS10 37-74LS14
37-74LS20 37-74LS27 10K Ohm, + 20%, 114W 8-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations E6, F6, H6) 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R73, 74) .001 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94)
.01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 PCB Assy. ortly: C103) .047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C56, 59) 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C17, 18) 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C78, 83-86)
1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C30, 89, 90) .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB Assy. only: C103; For -02 PCB Assy. only: C105) 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C44) 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C27)
150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C63) 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C82) 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C25, 64, 106) 47 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor (C104)
1 uf, +10%, 35V Tantalum Capacitor (C88) -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-39, 45, 46, 50-54, 61, 72-77, 79-81, 97, 98. Also, for -01 PCB Assy. only: C40, 41, 48, 49. For -02 PCB Assy. only: C42, 43, 50, 51) 100V Type-1N100 Switching Diode (CR11) 75V Type-1N914 Switching Diode (CR1, 3-10)
Type-2N3906 PNP Switching and Amplifying Transistor (Q3, 7) Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) Type-2N6044 Darlington NPN Transistor (Q4-6) Type LM319 Integrated Circuit (B12, D12)
Type TL082 Integrated Circuit (A10, D10) Type LF13201 Integrated Circuit (B10, D11, E10) Type TL084 Integrated Circuit (C11) Type 74LS00 Integrated Circuit (J4)
Type 74LS02 Integrated Circuit (N9, M7) Type 74LS08 Integrated Circuit (L5, P8) Type 74LS10 Integrated Circuit (K4) Type 74LS14 Integrated Circuit (B6)
Type 74LS20 Integrated Circuit (M5) Type 74LS27 Integrated Circuit (N7)
[Continued on next page]
a Figure 26 Battlezon e™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts:
| 37-74LS32 | Type 74LS32 Integrated Circuit | (J5, K10, L2, M8) |
| 37-74LS42 | Type 74LS42 Integrated Circuit | (B4, J7) |
| 37-74LS74 | Type 74LS74 integrated Circuit | (H10, L10, M9) |
| 37-74LS86 | Type 74LS86 Integrated Circuit | (D7) |
| 37-74LS109 | Type 74LS109 Integrated Circuit | (N8) |
| 37-74LS139 | Type 74LS139 Integrated Circuit | (C4, K5, M2) |
| 37-74LS157 | Type 74LS157 Integrated Circuit | (D4, E4, F4, H4) |
37-74LS161 Type 74LS161 Integrated Circuit (K6, L4, L6, M6, N6)
| 37-74LS164 | Type 74LS164 Integrated Circuit | (P9) |
| 37-74LS174 | Type 74LS174 Integrated Circuit | (C7, L7, M11) |
| 37-74LS175 | Type 74LS175 Integrated Circuit | (F8, F9, J8, K8) |
| 37-74LS191 | Type 74LS191 Integrated Circuit | (F410, J6) |
| 37-74LS193 | Type 74LS193 Integrated Circuit | (ES, F5, H5) |
| 37-74LS194 | Type 74LS194 Integrated Circuit | (A5, A6, B5, C5, D5, D6) |
| 37-74LS244 | Type 74LS244 Integrated Circuit | (K3, N2, N11, P11, R11) |
| 37-74LS245 | Type 74LS245 Integrated Circuit | (F2,P2,P4) Acceptable substitute is part no. 37-8304B. |
| 37-74LS273 | Type 74LS273 Integrated Circuit | (C8) |
| 37-74LS367 | Type 74LS367 Integrated Circuit | (F7, H7) |
| 37-74LS393 | Type 74LS393 Integrated Circuit | (M4, N5) |
| 37-74LS399 | Type 74LS399 Integrated Circuit | (H8) |
| 37-74LS670 | Type 74LS670 Integrated Circuit | (E6, F6,H6) Acceptable substitute is part no. 37-74LS170. |
| 37-74S00 | Type 74S00 Integrated Circuit | (C6) |
| 37-74S802 | Type 74S02 Integrated Circuit | (K9) |
| 37-74804 | Type 74804 Integrated Circuit | (K2, R9) |
| 37-74S74 | Type 74S74 Integrated Circuit | (J10, L9) |
| 37-74S260 | Type 748260 Integrated Circuit | (L8) |
| 37-7404 | Type 7404 Integrated Circuit | (H11) |
| 37-74193 | Type 74193 Integrated Circuit | (N4) |
37-7805 +5V Voltage Regulator (VR2) 37-7815 + 15V Voltage Regulator (VR3) 37-7915 ~ 15V Voltage Regulator (VR1) 38-MV5053 Type MV5053 Light-Emitting Diode (CR2)
| 41-3004 | 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke | (L1) |
62-001 SPST Momentary Pushbutton Switch (SW1)
| 66-114P1T | 4-Station Single-Throw, Dual-Inline-Package Bit Switch | (L11) |
| 66-118P1T | 8-Station Single-Throw, Dual-Inline-Package Bit Switch | (M10, P10) |
79-42024 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, J1, J3, K1, LM4, N41) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (L/M/N3)
| 81-4302 | Nylon Snap-In Fastener | - |
| 90-102 | 12.096 MHz, + .005%, Crystal | (¥2) |
90-6013 Microprocessor (L/M/N3) 90-7033 Random-Access Memory (A1, A2, B1, B2, C1, C2, D1, D2, H2, J2) 020670-01 Test Point 936408-01 Programmable Read-Only Memory {K7)
Figure 26 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) AD
Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts:
| 110000-101 | 100 Ohm, +5%, %4W Resistor | (R70, 75) |
110000-102 1K Ohm, +5%, %4W Resistor (R18, 20, 27, 67, 84-86, 94, 110, 128-133)
| 110000-103 | 120 Ohm, +5%, %4W Resistor | (R1-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 99, 125-127. |
In addition, for -01 PCB Assy. only: R48, 50, 69) 110000-104 100K Ohm, +5%, YW Resistor (R35-42)
| 110000-122 | 1.2K Ohm, +5%, YW Resistor | (R46) |
110000-151 150 Ohm, +5%, %4W Resistor (R103)
| 110000-153 | 15K Ohm, +5%, %W Resistor | (R93) |
| 110000-221 | 220 Ohm, +5%, %4W Resistor | (R24) |
110000-222 2.2K Ohm, +5%, YW Resistor (R45, 92, 102, 112, 114-116, 119-121, 123) 110000-223 22K Ohm, +5%, “4W Resistor (R28-32)
| 110000-270 | 27 Ohm, +5%, YW Resistor | (R111) |
| 110000-332 | 3.3K Ohm, +5%, %4W Resistor | (R87, 97) |
| 110000-392 | 3.9K Ohm, +5%, YW Resistor | (R47, 49) |
110000-471 470 Ohm, +5%, YW Resistor (R34, 104-109) 110000-472 4.7K Ohm, +5%, YW Resistor (R43)
| 110000-474 | 470K Ohm, +5%, %4W Resistor | (R113, 117, 118, 122) |
| 110000-561 | 560 Ohm, +5%, %4W Resistor | (R96) |
| 110000-680 | 68 Ohm, +5%, %4W Resistor | (R124) |
110000-681 680 Ohm, +5%, 4W Resistor (For -02 PCB Assy. only: R83) 110000-821 820 Ohm, + 5%, %4W Resistor (For -02 PCB Assy. only: R68, 69, 82) 110003-752 7.5K Ohm, +1%, 1/8W Metal-Film Resistor (R71, 72, 76-81, 89) 122000-225, 2.2 uf, +10%, 35V Tantalum Capacitor (C87) 122005-103 .01 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100)
| 137002-001 | Type 74S86 Integrated Circuit | (B7) |
| 137149-001 | Type 74LS11 Integrated Circuit | (J9) |
137159-001 Type DAC-08 Digital-to-Analog Converter (C9) 137158-002 Type AM6012ADC Digital-to-Analog Converter (For -02 PCB Assy. only: A9, D9) OR OR 137160-003 Type MC3410 Digital-to-Analog Converter (For -01 PCB Assy. only: B9, E9) 179010-001 12-Pin PCB Header (J19)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specilic written permission of Atari, Inc.. Sunnyvale, CA. This drawing Is only conditionally issued, and neither receipt nor possession thereof! Confers or transters any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., oa and for manufacture Under the corporation's wri z > ten license, no right to reproduce this drawing is an Granted or the subject matter thereat unless by oe Girtten agreement with or written permission from Ra the corporation fo} Bo af mo = YZ
m> z m
Figure 27 Regulator/Audio !| PCB Assembly A035435-02 c
Figure 27 Regulator/Audio Il PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54PO 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108. 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105, 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055 | NPN Silicon Transistor, Type 2N3055 | (Q3) |
37-LM305, 5V Linear Voltage Regulator (Q1)
| 37-7812 | +12V Voitage Regulator, Type 7812 | (Q8) |
| 37-7905 | —5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x 1%4-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
78-16014 Thermally Conductive Silicon Insulator (Q2, 9) 79-58306 6-Position Connector Receptacle (J6, 9) 79-58308 9-Position Connector Receptacle (J7)
| 79-58346, | 12-Position Connector Receptacle | (J10) |
79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 110000-010 1Ohm, + 5%, %W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, %4W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, + 5%, %4W Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, %W Resistor (R27, 28)
| 110000-103 | 10K Ohm, + 5%, %W Resistor | (R13, 14) |
| 110000-271 | 270 Ohm, + 5%, %W Resistor | (R1) |
| 110000-330 | 33 Ohm, + 5%, %W Resistor | (R3) |
110000-392 3.9K Ohm, + 5%, %4W Resistor (R6) 110000-562 5.6K Ohm, + 5%, %4W Resistor (R32, 33)
| 110000-752 | 7.5K Ohm, + 5%, %4W Resistor | (R7) |
| 110001-221 | 220 Ohm, + 5%, Y2W Resistor | (R9, 21) |
116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimun 25V Radial-Lead Capacitor (C2, 7, 16)
| 122004-224 | .22 uf Ceramic-Disc 25V Capacitor | (C6, 8, 15, 17) |
100015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)
99-10103 99-10052
99-10095
99-10064
COIN INLET CHUTE 99-10101
70-11-47
99-10105 & aa A > 99-10081 COIN MECHANISM vA SEE PARTS LIST oo (71-1200) ; : / Nf 75-9448 99-10102 65-441 a, COIN RETURN< —99-10065 . ' 72-9603S CHUTE WITCH WIRE ~ 99-10068 SEE PARTS LIST (99-1075 thru aw 99-10078) - COIN SWITCH ASSY. SEE PARTS ier 99-1008 PART OF 99-10047 (99-10042 thru 75-1412S 99-10082 99-10045) -
Figure 28 New Coin Door 71-10xXxxx D
COIN RETURN BUTTON ASSY.— SEE PARTS LIST 199-10072 thru 9910022, and 99-0107) ( COIN DOOR ONLY— SEE PARTS LIST (99-10009 and 10010)
99-10094
PART OF 99-10074
75-5520B
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specihic written permission of Atari, Inc., Sun nyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any rightin, or license to use, ‘ne subject matter of the drawing or any design or technical information shown thereon, nor aay right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Alari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is ranted of the subject matter thereo! unless by written agreement with or written permission from the corporation.
71-102201 — 25¢/25¢Coin Door 71-103202 — 25°125¢/25¢ Coin Door 71-103203 — 25¢/25¢/$1 Coin Door 71-102204 -- 2 DM/1 DM Coin Door 71-103205 — 1/2/5 DM Coin Door COIN RETURN BUTTON COVER— SEE PARTS LIST (99-10055 thru 99-10059)
PRICE PLATE—
99-10074 thru 99-1092, and 99-10108)
99-10062
75-915S, me 99-10051
71-102206 — 1 OM/5 DM Coin Door 71-102207 — 5 Fr/5 Fr Belgian Coin Door 71-102208 — 1 Fr/1 Fr Swiss Coin Door 71-102209 — 100Y!100Y Coin Door 71-102210 — 10 PHO P Coin Door
Figure 28 New Coin Door 71-10Xxxx D 72-JA1405B
99-10054
72-HA1404C
99-10061
99-10066
72-JA1405B
71-102211—20¢/20¢ Australian Cain Door 71-102212—100 L/100 L Italian Coin Door 71102213 — 50¢/50¢ (2 x 25¢) Coin Boor 71-103214 — 50%/50¢/50¢ Coin Door 71-103215 — 50¢/50¢/$1 Coin Door
Figure 28 New Coin Door, continued Parts List
Part No. Description
31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism
71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism
71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x 4" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16" Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75-915S. #14-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-944S #4-40 Polymer self-locking steel hex nut 75-948S, #8-32 Polymer self-locking steel hex nut 75-1408S, #4-40xY2" Slotted pan-head steel machine screw 75-1412S, #4-40x34” Slotted pan-head steel machine screw 75-5520B #¥%4-20x1¥%" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire)
Figure 28 New Coin Door, continued Parts List
Part No. Description
99-10045, Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coii assembly 99-10048, Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99:10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price piate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096 “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters
S1
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
a, 3rd printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm © Distributor
Address Operator
City State Zip _ CO Other.
Area Code Phone
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE. CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States
Second fold
eBpe siy) ede, “Wold
bE BES RE BEN REN REN RN. Ree 28
> id > a ERS SS ES ES ES ES
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Setter be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty, The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. : : : : : : :
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.