CATHODE RAY TOMES

Roads Edge (Hyper Neo-Geo 64)

Roads Edge (SNK) · Manual · 47 pages · 12 sections · original scan

Page 1

Sa

ROADS EDGE

HYPER NEO-GEO 64 LINK seTmINGs:

2-4 UNITS CAN BE LINKED TOGETHER FOR MULTI -PLAYER GAMES.

  • Thelink cable can be installed in either of the 2 available jacks. ( upper or lower serial cable input )
  • Connect the link harness from 1st communication PCB to 2nd, 2nd to 3rd, and 3rd to 4”.

¢ Use one cable for each link between games. Verify the link cable is connected with extra “play” in the length connections. Do not allow the link cable to become pinched or pulled. This will cause the CPU to recycle the network test function and reset the game.

© — Set the rotary switch id number on the communication board to position 1,2,3,or 4. Each machine must have a unique number between 1 - 4. You cannot use same number for id settings. This will result in an error in the communications.

¢ — Verify that the dip switch bank located near the rotary connector is set to 1, 3 on 2 ,4 off. [Positions ton 2 off 3on 4 off

These settings will allow you to use the factory installed link communications capabilities on the roads edge games. ( Multi player mode only accessible between linked units. ) lf you have any questions please feel free to fax or telephone us with your concems. Parts / Customer service ( phone ) 310 371-7100 ( fax ) 310 371 0969

Page 2

PRECAUTIONS FOR SAFE OPERATION

The procedures listed herein must be carefully followed to ensure both safe operation and to prevent personal injury and property damage. Before use, please carefully ready through the manual for proper usage methods. After reading it, be sure to keep the manual in a safe place for later reference.

WARNING . High voltages are present behind this
DANGER panel. There are no user-serviceable parts inside. Refer all servicing to Hl 4 \ f qualified personnel. To reduce risk of electrical shock, disconnect power supply cord before servicing. 497130037W

¢ This cabinet is for indoor use only. This machine should never be placed outdoors or used in the places listed below. Doing so may damage the machine and cause accidents.

  • In areas such as indoor pools or near a shower where humidity is high.
  • In areas exposed to direct sunlight. :
  • Near areas exposed to direct heat from a heater, etc., and around dangerous materials.
  • In excessively dusty areas.
  • In areas that are prone to water leakage and flooding.
  • Near ventilators and areas of severe temperature extremes.
  • In areas subject to severe jolts and unstable locations.
  • Near fire fighting equipment.

¢ Should any of the following occur, immediately turn the power switch off and unplug the cabinet. Continued use in any of these circumstances may result in accidents such as fire and electric shock.

  • When the cabinet breaks down.
  • When the cabinet is damaged.
  • When water or foreign matter enters the cabinet.
  • When smoke, unusual odors, or strarige noises emanate from the cabinet

Be sure to tightly connect all connectors. If insertions are partially or incorrectly made, these may result in accidents such as fire and electric shock.

  • Before changing software and performing other procedures, be sure the power switch is turned off and the cabinet unplugged. Performing procedures while the power is on may result in accidents such as fire and electric shock.

¢ Do not perform repairs or modifications on the cabinet yourself. Doing so may result in accidents such as fire and electric shock.

Page 3

Be sure to use an outlet rated at AC110-120V and insert the plug into a standard outlet. If other high-capacity products (air conditioners and large-size cabinets, etc.) are used on the same power line, this may result in accidents such as fire and electric shock.

Be sure receptacle is a 3-prong duplex - DO NOT USE a ground elimination adapters. If not suitably grounded, the cabinet may cause electric shocks in the event of a short circuit.

Place the cabinet as close as possible to the outlet and ground connections. Keep electric cords out of sight from customers. If exposing cables cannot be avoided, be sure to place a protective cover over them for protection. Do not forcefully bend, pull, or place heavy objects on cords.

If cords are damaged, they may result in accidents such as fire and electric shock.

While moving the cabinet with casters, move it s lowly being careful of the area around you. Make sure this is done with a suitable number of personnel and take proper measures to accommodate the cabinet’s size and weight.

Absolutely do not touch the back of the monitor. Because the monitor has high voltage parts, touching these even after the machine is unplugged may cause severe electric Shock.

Do not place any of the following materials on or around the cabinet. If liquid should spill onto or into the cabinet, it may cause accidents involving electric shock and damage the machine. -

  • Vases, potted plants, cups, cosmetic products, and containers holding medicine and water.

Do not use multiple appliances in excess of current capacity on a single outlet. This may. cause fire and electric shock.

Before moving the cabinet, be sure to unplug the power cord. This is necessary to avoid accidents and damage to the cabinet.

Do not damage the power cord and ground cable when moving the cabinet. This may cause accidents and damage to the cabinet.

Be sure to use specified parts and fuses meeting the specifications listed herein. Using parts not meeting these standards may cause damage or breakdowns.

Make sure the warning labels affixed to the cabinet can be read at all times. Be sure they are in an open place, well-lighted, and not dirty. Also, be careful these labels are not hidden by other objects such as game cabinets, etc.

Page 4

Do not unplug the machines if your hands are wet. This may cause an electric shock.

Do not mount the cabinet or place heavy objects on it. This will not only cause injury should it become unbalanced and tip over or fall, it may also damage the cabinet.

When unused for long periods, turn the cabinet off and unplug it for safety.

Place the cabinet where room temperature is between 5° and 35°. If the temperature exceeds or falls below the recommended temperature range, this may damage the cabinet.

During shipping or moving, avoid serious jolts to the cabinet. This may cause damage or breakdowns.

Be sure to use fuses meeting the specifications listed herein. Using parts not meeting these standards may cause damage or breakdowns-

Always use a Logic tester when checking IC port circuitry. Using a normal tester may cause damage or breakdowns.

When installing the cabinet, be sure to calibrate the adjusters to bring the cabinet level. Should it fall over, it may cause injury and accidents. If the machine is not level, there are times when the coin sorting function may not work.

Do not apply volatile liquid cleaners like benzene, alcohol, thinner, and insecticides to the cabinet. This may cause paint and stickers to peel and ruin the luster of the cabinet’s finish.

Raise the adjusters and move the cabinet. This is necessary to avoid accidents and injury.

Over graded areas, be sure to.remove the control section and seat section before moving the cabinet. This is necessary to avoid accidents and injury.

When disposing of this machine, make sure you do so according to the laws of your area concerning collection, shipping and disposal.

When disposing of this cabinet through the agency of another, be sure to do this through a suitably qualified agency.

Page 5

To Our Customers Precaustions for Safe Operations ... Specifications Convenience Kit Packing Check... Part Names .... Switch and Terminal Locations Moving and Shipping the Cabinet... Placing and Attaching the Seat Base . Attaching the Billboard Turning on the Machine .. Test Mode ... Main Menu... Memory Test .. Network Test .. I/O Test ..... Sound Test . Coin Data .. Game Options System Options . Maintenance .. Control Panel Pedal Assembly . Hyper Neo-Geo 64 PCB Unit Inserting/Removing Software Cartridges . - Overall Harness Drawings... cece eeeeeeseeeceeseeceseceeesereeeeeeteeeeee - 44-45

Page 6

SPECIFICATIONS

*Specifications may be changed without not Model number: RE29-S

1) 2) 3)

4) 5) 6) Power supply: PETER CHOU 44-1065 AC110-120V Power consumption: 200W Cabinet section: 37”(L) x 40” (W) x 80” (H) includes height of pallet Seat section: 22”(L) x 40.5” (W) x 59”(H) includes height of pallet - Total weight: 500 lbs. Internal monitor: NEOTEC NT29-C Fuse Standard: 7A/250V

CONVENIENCE KIT

PACKING CHECK

  • Mounting bracket left
  • Mounting bracket right
  • Bolt hex M8 x 30 mm black
  • Washer flat M8 black
  • Washer split lock M8 black
  • Screw Phillips Pan head #8 x 3/4 black
  • Washer flat #8 black
  • Link cable _
  • Wrench Allen M5
  • Manual

Be aware that the items listed herein are subject to change without prior notice for-product improvement.

This cabinet is packed in the method below: =

  • Number of packages: 2
  • Package contents: Monitor Base Seat Section

Because packing will be needed subsequently for shipping between locations, store the cardboard boxes and pallets, etc., in good condition in an suitable location.

The convenience kit is packed in the coin box. Remove the kit and check contents.

Page 7

PART NAMES

Front

Lamp panel assembly

Page 8

SWITCH AND TERMINAL LOCATIONS

Control Panel: Inside the service door, the following switches and terminals are accessible.

  • Volume - Adjusts the volume levels of the front speakers.

peony LIME SONTRO iaRATION po a / x

  • Power plug
  • On-Off switch
  • Fuse
  • Volume - Adjusts the volume levels of the seat speakers.
  • Volume - Adjusts the volume levels of the woofer in the seat.
  • Service switch - The service credit switch.
  • Test switch - The switch that begins the Test Mode.
  • Coin counter - Counts the amount of coins. =

Power plate: In the rear power section, the following switches and terminals are accessible.

Page 9

MOVING AN

When moving or shipping the cabinet, be aware of the points listed below.

  • When moving and carrying the cabinet over graded surfaces, be sure this is done with the control panel and seat section separated. Separating parts is to be done in the reverse order of the procedures used to assemble the cabinet during installation.
  • Use a forklift only when the cabinet has been fully packed.
  • When moving the control panel section separately, be sure to push it in the orientation and direction shown in the diagram below. .

*CABINET IS TOP HEAVY!

  • Move the cabinet as shown here.
DANGER
  • When moving the cabinet, be sure to do so with the appropriate number of personnel. If the cabinet should fall or tip over, it may cause personal injury and other accidents.
  • When moving the cabinet, be careful of conditions around you and create a path sufficient to safely move the cabinet.
  • Before moving the cabinet; make sure the power cord is unplugged. This is necessary to avoid accidents and damage to the cabinet.
  • Do not damage the power cord when moving the cabinet. This may cause accidents and damage to the cabinet.
  • Moving and shipping should be carried out with a number of personnel. This is necessary to avoid accidents and personal injury.
  • When moving the control panel separately, be sure to move it in the orientation and direction specified. If the cabinet falls over, it may cause personal injury and other accidents.
  • Do not damage the wiring. This may cause fire and electric shocks.
  • When moving the cabinet in an unpacked state, do not use a fork lift. There is the danger of personal injury should the cabinet tip over or-fall.
WARNING
  • Do not move the cabinet with the adjusters lowered. This may cause personal injury and accidents. :
  • When separating the cabinet’s sections, keep careful track of removed parts and screws so you do not lose them.
Page 10

PLACING AND ATTACHING THE SEAT BASE ;

Necessary Entrance Dimensions At the time of shipment from the factory, the cabinet is shipped with the control panel and seat sections separately packed. Each package’s size and weight are shown below. Check the size of your entrances to see if these can be accommodated.

¢ Cabinet section: 37”(L) x 40” (W) x 80” (H) includes height of pallet © Seat section: - 22”(L) x 40.5” (W) x 59”(H) includes height of pallet e Total shipping weight: 500 lbs.

Placing Conditions The areas needed for operating and maintaining the machine are shown below. e Single-cabinet use: 33” (W) x 72” (D)

more than 1maSom

F q E g :

Aisle

This cabinet can be linked with up to four cabinets for communication competition. When using communication links, place cabinets as listed below. =

¢ As with single-cabinet usage, the back of cabinets should be placed apart by more than 50 cm. ¢ As with single-cabinet usage, the edges of both sides of the cabinet should be separated by more than 50 mm from walls and other cabinets. ¢ Cabinets in a communication network should be placed so the communication cables easily reach the other cabinets.

Page 11

Preparations for Installation Before installing cabinets, locate convenience kit and check for the following:

¢ Billboard, Left and Right seat mounting fixtures, and attaching hardware e Allen wrench

Installation Methods Connecting the control panel section and the seat section.

  • Loosely fasten the seat mounting fixtures (Left and Right) to the locations shown in the diagram of the control panel section with the hex bolts and washers.
  • At this time, fasten these loosely.
  • Position the control panel near the seat section and connect the seven connectors.
WARNING : ~ Be sure machine is not plugged into electrical outlet.
Page 12
  • Lower the adjusters at the bottom of the control panel section (four locations) to the surface. When they are set on the surface, use the spanner to adjust the height of each adjuster and bring the cabinet level (the casters should be about 5 mm off the ground).
  • Adjust the four adjusters on the bottom of the seat section to the same height of the control panel section.

= Cosier Wi Raise Adjuster o bout Smm SS —

  • Lower .

~Ptacement surface ; Directions for tuming adjusters

  • Being careful not to pinch the connectors and harnesses, attach the control panel section to the seat section.
  • As shown in the diagram, attach the four hexagonal bolts (M8 x 15) to the seat section.
  • Tighten the hexagonal bolts loosely screwed into the cabinet in step (1).
  • When separating the sections, follow the above procedures in reverse order.
DANGER — e Under no circumstances should the cabinet be placed in the locations listed below. So doing may result in accidents such as fire and electric shock. -
  • Indoor pools, areas near a shower, and other locations where humidity is high.
  • Inareas exposed to direct sunlight. : ~— Inareas that are excessively hot, like next to a heater. In areas around dangerous materials.
  • In places that are excessively dusty.
  • In areas prone to leaking or flooding.
  • Near ventilators and areas of severe temperature extremes ~ On inclines, areas subject to severe jolts, and other unstable locations.
  • Near fire fighting equipment, etc.
Page 13
  • Do not place any of the following materials on or around the cabinet. If liquid should spill onto or into the cabinet, it may cause accidents involving electric shock and damage the machine.
  • Vases, potted plants, and containers holding medicine, water and other types of liquids.
  • Heavy objects

© Be sure to lower the eight adjusters of the control panel and seat sections to the surface and stabilize the cabinet. If not stabilized, it may result in personal injury or accidents.

¢ Set up the cabinet according to the explanations and procedures listed in this user’s manual. If these are not followed correctly, there is a danger of accidents involving electric shock and other personal injuries.

e Use the cabinet with indoor wiring meeting the proper voltage specifications. Failing to do so may cause fire or electric shock.

« Absolutely do not use numerous appliances on one outlet. It may result in fire or electric shock.

  • Do not damage, bend, or placing heavy or hot objects on the power cord. If the cord is damaged, this may cause accidents involving fire and electric shock.
WARNING ¢ Do not place the power cord in areas where people can step on or kick it. This may result in personal injury and accidents.
Page 14

ATTACHING THE BILLBOARD

  • Attach the billboard to the control panel’s lamp box with provided screws.

RQUEE MARQUEE _

WARNING 7 ; ; « Before beginning assembly, have a footstool ready and use it for assembling parts. Trying to “assemble parts without a footstool may cause accidents and personal injury. ¢ Be sure to tighten screws securely. ; , _ If screws become loose, this may damage parts and cause accidents. ; e Prepare enough space to safely set up the cabinet. Failing to do so may cause accidents and _ personal injury. TURNING ON THE MACHINE . _

e . Turn on the machine and check the following;

  • Check to see if the rear power switch is “OFF.”
  • Plug the AC cord into the outlet.
  • Connect the ground cable. 4> Switch “ON” the power switch on rear power plate.
WARNING ; ¢ When turning on the cabinet, do not touch the steering wheel. = If the power switch is not switched on, the cabinet will not operate.
Page 15

Checking Operations

  • The fluorescent light turns on.
  • After the power has been turned on, the RAM TEST will automatically begin. If all displays show [OK], the next display will appear. For a few seconds at this time, each lamp will turn

on and off.

  • After the crosshatch screen appears for a few seconds, the screen will change to the

“Network Check” screen.

  • 4. The “Network Check” screen will be displayed. for about 40 seconds whether the cabinet is connected for communication competition or not. After this, the game screen will then appear. At the same time the “Network Check” screen is displayed, the steering wheel will automatically straighten itself out.
WARNING . e During the “Network Check,” absolutely do not touch or try to use the steering wheel, pedal, shift lever and switches. This will cause the cabinet to malfunction. Ifthe steering wheel does not return to its home position, check the connections again.

. When you press the Test switch inside the service door, the Test Mode begins. Settings and adjustments you can make in the Test Mode are listed below.

MEMORY TEST (Memory check) Checks the read/write capabilities of the RAM device.

MONITOR TEST (Display check) _ Ascreen display for adjusting the monitor.

: NETWORK TEST (Communication check) Displays the condition of communication between cabinets.

1/O TEST (I/O check) Checks all types of input devices.

SOUND TEST (Sound check) Checks the output of all sound-system devices.

_ COIN DATA (Income totals) Shows coin/play totals. ‘ -

GAME OPTIONS (Game settings) Sets game difficulty levels, etc.

SYSTEM OPTIONS (Cabinet settings) Sets all cabinet characteristics.

Page 16

While conducting the Test Mode with multiple cabinets connected in a linked communication network, be careful of the points below.

¢ Check whether power switch is connected. ¢ When a number of cabinets are connected in a communication network and the Test button is pressed, all connected cabinets will enter the Test Mode. If there is a cabinet that is in operation, do not push the Test switch. ¢ During communication play, when a communication error occurs, the game will be forcefully stopped and cabinets will enter the Network Test Mode.

SCREEN DISPLAY

MAIN, MENG

  • WEWORY. TEST MONITOR TEST

“SINK sux corporation 1997

ACTIVATION METHOD During the game, when the Test button is pressed, this menu is displayed.

BASIC OPERATION INSTRUCTIONS

  • Move the arrow (*) with the shift lever and match it to the item you wish to change. -
  • CURSOR UP: The cursor moves up. ° .
  • CURSOR DOWN: The cursor moves down. 2, Make settings according to the operation instructions in the lower left corner of the screen. (There is an operation explanation for each selected item.)
  • ENTER: Step on the accelerator (pedal) te-call up the item contents. =
  • CHANGE: When you step down on the accelerator or brake, the item contents will change.
  • Choose the EXIT display in each item and step on the accelerator to return to the previous screen.

END: To get out of the Test Mode, match the cursor to EXIT and step down on the accelerator. (Restart the cabinet to go to the game.)

Page 17

SCREEN DISPLAY

MEMORY TEST SCROLL RAM PALETTE RAM

For the items on the left, OK or NG (No good) test results are displayed.

EXIT ; ACCELERATOR SNK © snk corporaTion 1997

OPERATIONS The memory is checked automatically and if there is nothing wrong an “OK” will appear. If there is something wrong, an “NG” is displayed.

*When an “NG” message appears, quickly turn the cabinet off and contact your nearest SNK Service Center.

FUNCTIONS The test pattern for adjusting the monitor is displayed. Three types of screens are displayed: a color bar for correcting color tones, the crosshatch for correcting image and size distortions, and the monitor adjustment screen.

_ 1. COLOR BAR [Color Tone Adjustment]

EXIT : ACCELERATOR SNK © shk conPoRATION 1997

Page 18
  • CROSS HATCH [Positioning Adjustment]

SGRREEEED

  • MONITOR CHECK [Screen Adjustment]

EMOSRWG

Based on sample images, color misalignment, r rasters, display scaling, brightness, contrast, sizes possible for stabilized displays, and screen center images are examined.

Page 19

NETWORK TEST

SCREEN DISPLAY

NETWORK TEST

01:0K 02: — 03:0K 04: — a a => ‘\— [ite

SNK © six corporation 1997

Communication settings and Ds are displayed. ~ ID NUMBER: Connected SEARCH: Searching : _ LINK: ~ | if the ID numbers are displayed after more than two minutes, there is something wrong with the network.

FUNCTIONS 7 Checks communication settings and displays communication circumstances.

ID CHECK Displays the ID number of the cabinet and the ID numbers of each connected cabinet.

SYNCHRONIZING CHECK . . Displays communication circumstances.

Page 20

SCREEN DISPLAY

\/0 TEST

SINK © sux corporation -1997

  • [Input Test]

INPUT TEST

Bau HANDLE GEAR

C000 +H

00 Oo !00 ol 4: VIEW START BRAKE ACCELERATOR Input data is reflected on successive screens. By stepping down on the accelerator and brake simultaneously, it is possible to exit from this screen. °00 0 Oo COIN SERVICE TEST

STEP_ON THE THE BAER nD TO EXIT SNK © sux corporation 1997

CHECK CONTENTS . Steering wheel, accelerator, and brake input is carried out through analog input.

¢ The steering wheel center value is “80,” turning all the way to the left is “O,” and turning all the way to the right is “FF.”

  • Steering wheel 1-digit values can vary slightly, but this is normal. «If the brake and accelerator are not being stepped on, a full left turn “O” condition is represented as “FF.”
Page 21
  • [Output Test]

OUTPUT TEST —> BGM SELECT#1

ON: Always lit up BLINK#1: Lights up

WINNING LAMP REACTIVE STEER EXIT 7 we ger uw The reactive steering wheel, when this CURSOR item is selected, automatically rotates CURSOR DOWN =H. FT DOWN from right to left to canter and displays GiANGe a 5 BRAKE this information successively. SNK © sux corporation 1997 ON OFF BGM OFF BGM SELECT#4 = OFF ON OFF BL OFF

There are four types of winning lamp patterns. _ When the reactive steering item is selected, a warning message is displayed.

  • ANALOG DEVICE ADJUST [Sets basic analog standard values]

ANALOG DEVICE ADJUST

apie YOUR HANDLE NEUTRAL PUSH THE START BUTTON

WITH ‘OUR LEGS OFF THE ACCELERA’

T : ACCELERATOR SINK © snk corporation 1997

When all settings are made, an “OK” message is displayed.

When you press the Start button with the steering wheel in neutral and your feet off the accelerator and brake, you can match the centers of each part.

  • The Start button is deactivated when you step down on the accelerator.
Page 22

SCREEN DISPLAY

SSN © sn corporation 1997

FUNCTIONS Performs tests of music and sound effects.

  • BGM (Background music) - ° When selected, the BGM will begin to play simultaneously. (All sounds playing beforehand will be canceled.) After selection, this is played only for 10 seconds. You can cancel the test by stepping down on the brake when the sound is playing.
  • SE [Sound Effects] ¢ When selected, the sound effects will begin to play. (All sounds playing beforehand will be canceled.) 7 After selection, this is played only for 10 seconds. You can cancel the test by stepping down on the brake when the sound is playing.
  • LEFT SPEAKER [Speakers on the left side]
  • Based on the view from the seat, plays sound through all speakers on the left side. e The sound will continue until the brake is stepped on or another item is selected.
  • CENTER SPEAKER [Central speakers]
  • Plays sound through the right and left speakers. e The sound will continue to until the brake is stepped on or another item is selected.
  • RIGHT SPEAKER [Speakers on the right side] Based on the view from the seat, plays sound through all speakers on the right side. The sound will continue until the brake is stepped on or another item is selected.
Page 23
  • REAR SPEAKER [Speakers in the rear of the cabinet] ¢ Plays sound through the speakers located in back of the seat. The sound will continue until the brake is stepped on or another item is selected.
  • VIBRATION DEVICE [Vibration device levels} ¢ Sends sounds through the vibration device located under the seat. ¢ The sound will continue to until the brake is stepped on or another item is selected.

COIN DATA

SCREEN DISPLAY

COIN DATA

  • DAILY COIN DATA MONTHLY COIN DATA

: SHIFT UP. : SHIFT DOWN : ACCELERATOR SINK © sue corPoRATION 1997

FUNCTIONS . ¢ The coin data for all cabinets linked through the network is displayed. ¢ Income total data and play frequency data is displayed.

  • Totals for the past week by time
  • Totals for the past year by month.
Page 24
  • DAILY COIN DATA

DAILY COIN DATA

EXIT : ACCELERATOR SNK © su corporation 1997

SERVICE

Play Continue Average Number of Number of Service frequency frequency playtime coins 1 coins 2 frequency

Page 25
  • MONTHLY COIN DATA

WONTHLY COIN DATA

  • NEXT [ 1/2 ] EXIT

CURSOR UP :SHIFT UP CURSOR DOWN :SHIFT DOWN ENTER ACCELERATOR SINK © six CORPORATION 1997

SERVICE

97/01 JAN

Play Continue Average Number of Number of Service frequency frequency Playtime coins1 coins 2_ frequency

Page 26

GAME OPTIONS

SCREEN DISPLAY

FUNCTIONS. HARD NORMAL NORMAL MPH ALL THE TIME ENGLISH RIGHT

DEFAULT IN BLUE

Sets software dip settings, such as game-difficulty, etc. Settings for basic game contents is done here. : When making connections for a communication network, if there is a faulty connection or a cabinet’s items (GAME OPTIONS) are changed, all settings are-simultaneously changed for the other cabinets.

. DIFFICULTY

EASY NORMAL HARD _ HARDEST

Total: 4 types =~ Initial settings: “HARD”

Page 27
  • NUMBER OF LAPS (TRIAL)

® LONGEST

Total: 5 types Default: “NORMAL”

Sets the standard laps of the Trail Mode.

  • NUMBER OF LAPS (VS PLAY)

NORMAL

Beginner23
Intermediate123.|[18
‘Advanced123416

Total: 5 types Default: “NORMAL”

Sets the standard laps of the Competition Trial Mode.

  • SPEED DISPLAY .
  • km/h - Displays the speed meter units in kilometers per hour.
  • Displays distance meter units in meters.
  • Displays course information in meters.
  • MPH_ - Displays speed meter units in miles per hour.
  • Displays distance meter units in miles.
  • Displays course information in miles and feet.

Total: 2 types Initial setting: “MPH”

Page 28
  • DEMO SOUND TRACK
  • ALL THE TIME Plays music all the time during demo screens.
  • ONCE EVERY 2 Plays music once every two demo screens.
  • ONCE EVERY 4 Plays music once every four demo screens.
  • BGM OFF Doesn’t play music during demo screens.
  • SOUND OFF Doesn't play any sound during demo screens.

Total: 5 types Initial setting: “ALL THE TIME”

“DEMO PLAY” is the only item where you can choose whether sound plays or not.

  • LANGUAGE
  • Japanese
  • English

Total: 2 types Initial setting: “ENGLISH”

  • TRAFFIC LANE
  • Left _
  • Right

Total: 2 types / Initial settings: “RIGHT”

Decides whether other cars drive mainly on the right or left sides.

Page 29

SYSTEM OPTIONS

SCREEN DISPLAY

SYSTEM OPTIONS —> COIN/CREDIT SETTING CALENDER SETTING BACKUP MEMORY CLEAR EXIT

ENTER EAGCELERATOR | SSNIKK © SNK CORPORATION 1997 |

FUNCTIONS > ¢ When the communication network is set up, making item changes (SYSTEM OPTIONS) on any one of the cabinets will simultaneously alter settings on the other cabinets. e Performs system information settings. :

  • Sets coin shooter and credits.
  • Sets the calendar.
  • Initializes the back-up memory.
  • COIN/CREDIT SETTING

COIN/CREDIT SETTING OFF COMMON COINS 3COIN 1CREDIT 3COIN 1CREDIT When the FREE PLAY item is set to ON, credit

ERATOR: . SINIK © six comPoRATION 1997

Page 30

Settings can be made for each coin shooter from 1COIN 1CREDIT to SCOINS SCREDITS.

SNK © sxx conPORATION 1997

  • CALENDAR SETTING

CALENDER SETTING 97 / 06 / 09 (HON) 16 : 05 97 / 06 / 09 (MON) 16°2' 05 SET

After matching lower calender dates with the cursor A, the calendar Settings are altered when the cursor is moved to the SET item.

SINK © suc corporation 1997 eee

  • BACKUP MEMORY CLEAR

When settings are determined with “YES,” 5 the data for credit total information, etc., will be cleared. = Cabinet information, credit settings and Software dip information is not cleared.

SNK © sxc corporation 1997

Page 31

Changing Fluorescent Lights and Lamps « Methods for Changing Fluorescent Lights and Lamps in the Control Panel Section.

  • Remove the fluorescent light (15 W), the glow bulb (FG1E), and the lamp (S35 E17Y8W). Replace these with new ones.
  • Put the lamp box back together following the procedures in reverse.
Page 32
DANGER ¢ Make sure these operations are done with the power off. This can cause accidents involving electric shock and personal injury. e During replacement procedures, do not touch any other areas than those indicated. This can cause personal injury and accidents. ¢ Do not use replacement parts other than those designated by the SNK Corporation. Doing so can cause accidents and damage to the cabinet.
WARNING e Make sure all screws are screwed in tightly. If screws become loose, it may damage parts or cause accidents. e Because lamps and fluorescent lights become very hot right after the cabinet is turned on, wait a while before beginning to replace lights and lamps.

CONTROL PANEL

On the Test Mode screen, when the volume values of the steering wheel are shown to be abnormal, it is necessary to change the volume.

Abnormal examples : Even when the steering wheel is turned all the way, a “O” or “FF” reading does not appear.

  • e Even when the steering wheel is not turned all the way, a “O” or “FF” reading appears.

e Removing the Control Panel Assembly

  • Remove the five screws shown in the diagram below and remove the upper control panel.

Control panel (upper)

Page 33

OPweN

a Remove the screws on the upper surface shown in the diagram below. Remove the bolts of the lower area shown in the diagram below. Pull out the control panel assembly forward until there is a gap you can fit your hand into. With your right hand, support the control with your left hand.

‘Speaker box

  • Disconnect the four ecto!
DANGER Make sure the power has been turned off before beginning to replace parts. Failing to do so may cause accidents involving electric
WARNING -
  • Because the control panel unit is very heavy at 12 kg, perform procedures carefully. Directly after the game is finished, because the motor is still extremely hot, wait a while after the game before beginning to remove_parts. When the control panel is pulled forward, be sure to support it with your hand. Failing to do so may damage the panel and cause accidents. Be sure to hold the housing when removing connectors. Pulling on the cords will damage them. | panel assembly and remove the four connectors

. Pull out the control panel assembly at the end.

shock and personal injury.

Page 34

¢ Replacing Volume Knobs

  • Loosening the hexagon socket head cap screw is sufficient. If these are removed, be careful not to lose them.
  • Pull out the connector.
Page 35

“WARNING

  • After soldering parts together, be sure to insulate these with electrical tape, etc. Without insulation, these may cause accidents involving electric shock.

¢ Attaching the Control Panel

Reassemble following the removal procedures above in reverse.

WARNING -
  • At the time of assembling parts, be careful not to pinch harnesses. This may cause damage to the cabinet.
Page 36

& ¢ Adjusting Volume °

  • Turn on the cabinet and go to the “Analog Standard Value Settings” item of the Test Mode.
  • In the Test Mode’s “Input Test,” check to see if the cabinet is operating properly.
DANGER
  • Following removal and replacement procedures, do not touch areas other than those indicated. Doing so may cause injury and accidents.
WARNING
  • After replacing the volume knob, be sure to perform necessary adjustments. If these are not made, there are cases where the game will not operate normally. Make certain all screws are tightened. If screws become loose, they may damage parts and cause accidents.
Page 37

PEDAL ASSEMBLY

« Removing the pedal assembly.

  • Remove the two screws and pull up the pedal assembly.
  • When the two connectors are disconnected, remove the pedal assembly.

‘After puling the assembly towards you, temember to disconnect the connectors.

DANGER
  • Make sure the power has been turned off when removing parts. Failing to do so may result in accidents from electric shock and personal injury.
Page 38

HYPER NEO-GEO 64 PCB UNIT .

Explanation of Parts 64 bit sofware ROADS EDGE

Hyper NEOGEO 64 PCB PCB unit driving game specification

WARNING = "
  • The PCB unit of the cabinet is customized for the Road’s Edge cabinet. Do not use other Hyper NEO-GEO 64 software cartridges.
  • Do not take apart the PCB unit and software cartridge.
DANGER
  • When removing/inserting software cartridges and replacing connector connection areas and unit parts, be sure to turn off the cabinet and unplug the power cord from the outlet. If procedures are done with the power on, this may cause accidents like electric shock and cause personal injury.
Page 39

= INSERTING / REMOVING SOFTWARE CARTRIDGES

Slide the seat back to its farthest 5

1. Slide the’ seat back to its farthest position. Pull up the peat cy

_2. Remove the two screws shown in the diagram. Next, use the included two common keys and open the seat base cover. :

Page 40

D. &

ANGER When inserting/removing software cartridges, be sure to turn off the cabinet. Failing to do so may cause accidents involving electrical shock and personal injury. When inserting software cartridges, be sure to turn off the cabinet and unplug the power cord from the outlet. Performing operations with the power on may cause accidents involving electrical shock and personal injury.

Installing Software Cartridges First, while being careful of the position of the software cartridge as shown in diagram A, push the cartridge securely into the guides along the sides of the PCB unit. Install the cartridge into the connectors. After installing the cartridge, be sure to fasten the lock levers on the side of the PCB unit onto the software cartridge as shown in diagram B.

Diagram A (Be careful of the positioning of the software cartridge.)

Software cartridge Diagram B

WARNING Be sure the lock levers_on either side of the PCB unit are securely clamped onto the software cartridge. When the lock levers cannot be sufficiently clamped, because the installation is incomplete, push the software cartridge down securely into the connector. When the software cartridge is in use and at times of shipping, make sure such objects as foreign matter and conductive materials do not get into the connectors underneath the software cartridge.
Page 41

a

« When Removing Software Cartridges Pull back the lock levers 90* as shown in diagram C and release the locks. Next, push levers in the front and back of the software cartridge down together and remove the software cartridge. Diagram D

WARNING - . When installing (and removing) the software cartridge, do not touch the parts on top of the PCB and the various harnesses and plate edge sections, etc. This may damage the cabinet and cause’ personal injury.

Things to Note When Connecting the Communication Cable « Always place the communication PCB’s dip switches to 1 & 3 to ON and those of 2& 4 OFF. © Set the rotary switch of the communication board between 1 and 4. Because the ID number of cabinets is set with this switch, be careful that the number is not set to that of another cabinet. e Because there is no distinction between input and output in connection terminals, connector plugs can be placed in any of these sockets.

A1

Page 42
  • When cable connections and board settings are finished, close the seat base cover and turn on the cabinet. © While the “Network Check” screen is displayed, turn on the other cabinets. If the communication set-up has been done correctly, the game screen will appear.
WARNING
  • For connecting the link cable, to prevent electric shock and damage to electric circuits, be sure to turn the cabinet off before beginning procedures.
  • So the link cable is not tripped over, be sure to run it through the back of the cabinet.

The monitor in this cabinet is adjusted to optimal performance at the time of shipment from the “factory. If for some reason it becomes necessary to make adjustments, make sure it is done by a technician who has experience and knowledge regarding the daily maintenance and supervision of amusement machines. Under no circumstances should areas not designated herein be touched.

Page 43

Explanation of Adjustment Functions

| te = BRIGHT | Brightness Adjusts image brightness V. HOLD | Vertical hold Use when the screen runs up and down

BRAG V. SIZE | Vertical size Adjusts vertical image v. HoLD~ | sue

Vv. SIZE — V. POS! | Vertical positioning Adjusts vertical image v. POS |-—— position

é H. HOLD | Horizontal hold ‘Adjusts image H. POS! precraehaiesyo DG TrorTre

H. SIZE H. POS! | Horizontal positioning | Adjusts horizontal ‘ image position

H. SIZE | Horizontal size Adjusts horizontal _ image size aa (74 = EM

WARNING = . Inside this cabinet, there are areas that contain a high-voltage of over 25,000 volts (FBT section, etc.). Even when the power has been turned off, because there are instances where these parts still contain an electric charge, under no circumstances should parts other than those designated be touched. There is the danger of severe injury’and even death.
Page 44

Sa aiel ADJUSTING THE MONITOR

7 Be eS So Ge & & re stem =| FG BE BE NSB W-HOLD V- SIZE BRIGHT —GGAIN W- POST = V-POSI Vv -tOLD BGAIN GAIN

Page 45

Tuy G evi ino | Same Operation 1 R-GAIN | Red signal amplitude ~Tadjusts red signal amplitude |

2G-GAIN|Green signal amplitude | Adjusts green signal amplitude
R-GAIN3BGAIN|Blue signal amplitude | Adjusts blue signal amplitude

~ 4 | BRIGHT | Brightness [Adjusts image brightness

G-GAIN5Vv. HOLD | Vertical holdUse when the screen

runs up and down B-GAI

BRnGit6V. SIZE | Vertical sizeAdjusts vertical image

Vv. HOLD at

SIZE L

7V. POS! | Vertical positioningAdjusts vertical image

. POS |I-—j . position

  • HOL -
H. POS!|H.HOLD[Horizontal holdAdjusts image

funning right to left

4,SIZE9 | H.POS!|Horizontal positioning | Adjusts horizontal

image position

10H. SIZE | Horizontal sizeAdjusts horizontal

adie (ye Gis L

Page 46

TO ULL. BRACKET {A [RELEASED FOR PRODUCTION Vw | IS

J27

—*. a x©Wut
seila@BRACKET

Ye | [te 1010] '

ace12WIN LANES -
ail BeHYPER NEO-GEO 54Peete-ey] N64S
ayLVS-LACLan=
°oo |5\3) aecoIN-SAB |*
Eaee|[Sse 88.COWNTER|=a=
1234Fua~T2345 678wy
au-1018-BH clelsieide) 8FEETa
Be | 9) /BK=l=o
We} $/5 We=|

BK ala BK =

55wys
teRE-1016-00saeiS

= =

J-60al~
400TTtOGcasteRE-1003-00EEEiad
20 aangMONITORwa 35 pe2dae
COIN co7SIPS
ESegas =|STEP DOWNFEEPEE
eE-1018-00“TRANSFORMERs-
To 56sey ETiS

200¥ POWER =

SUPPLYJHI10OPTIONALae
FLOUR SCENTaanies“omRE- 1003-00aBRAKE LIGH
LAMPRE- 1008-00wefca ALal J2
RE-1007-00ag)see, sles) J-6
J-503J4be pe
anesRE-1003-00eat akwhoan
UL433fecoe ercay LV S-LOA
BRACKETRET0000 ~~ RE-1004-00a
—E@--@-*,tse |
=5hl;asselseecd sia 5ae = = 32
a: eeé-1002-00fecreeeetniast a
La Shad.SRSRSS SSS Se =|RE- 1019-00
RE-J001-00"¢|HLWT Ss

eo) T weacre ADVANCED MANUFACTURING & DEVELOP Tewagies Aimee ms Mu. Oo (STONER SNK DG, TIME: a UMS EOE QVERALL WIRING ee [pee © RE-1000-01

/ORAIN BY:joATe:| CHECKED BYATE:
HOae neea
Page 47

PER NEOQ-GEU 64 nats | SEE zed -orfh seseaeetongeage ie A errs peceegeeamniny a eae RE

ena (IMM) TP.S. |

RE-1018-01 TOPS.

RE-1023-00 nea wer Wier In

fer

¥ e t L

et St we rt) st we me cag we

ney sail 2 +H

c ie

$56

+36 wa a ia cs

co ca —_e ca “1 is

ca te

+B

a {ox | UL. BRACKET

_——aky

{it

[a

[ie a)

[ar (ae {aL [a], +46 RE-1018-0) ay Le r T i fl ' '

t

r b

Is

a nN fF q

I i t RE-1018-01

+20 RE-1018-04

RE-1018-04

RE-1018-05,

TO PS

LVS-ACA RE-

RE=1018-01 = ig

RE-1018-01 8-01

7 ee Oe cate RE=1018-06

i ET PEDAL ASSY.= 2 2 Keo 1U1G-U2

ne AE U.L BRACKET

iT]

oJ pe- 1014-00 ul

CRT COLOR MONITOR

-1012- cs

FEWEW

j =e] i ©

+ ie

ad eS 0) ax ax +23

+15 J-SPEAKER

H a {es ‘a jax Re-1018-021

S|. 5 | vo é| ™ h

in

pf amc ia

ace, Loa

ua

va

so Ler [a

re La [a

rr nt TO_TRANSFORMER

RRS fray

ep jal

iq SEAT

RE=101)-00 SPEAKERS H “ :

A VIEW CHANGE

Ei

bid

a

Fra 3 [re-r0ve-o7 TH I-37 ‘I | Re-1013-00 a a

SPEAKER

DASH SPEAKERS The

RE-1018-05

i

i)

I

!

i

i} | RE-1018-01

3 RE-1015-00 Re-1022-00

J vt om a Wr i =—3y|

ci RE-1025-00

“ a (a tr (er a

Jil s

3K HY SIs HA HH HB

LVS - LAC Triese cE ad +19

a BEES Ss Ee oe ee

RE-1024-00 RE-1024-01

r

1 BGM

i i 1 View i

1 io:

‘7 (| s ‘| Oat

iu

+3) es [ea a TOLAWS RE=1005-00

52}

Lae] eee (rari J

J

UA

meas TERME: Tt: site

TOMS FOWLER.

Ges V- 1 E TESS pe A> SMUT SIF xv 050 DOES 12-10-97

“4/015 DOES »@ aoe SNK

wo ENON EOE 1 weRACTINE T EOMLOGIES 7 WG. IME:

is me RE-1000-01

—s Crd FAC TT ABTS

ys Mel

set li “DVERALL WIRING ADVANCED MANUFACTURING & DEVELC

MLUUTS,