Red Baron TM-169 1st Printing
Red Baron (revised hardware) (Atari, 1980) · Technical Manual · 64 pages · 49 sections · original scan

This page is a drawing, shown as the original scan.
GAME SERIAL NUMBER LOCATION r
Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/- Audio II PCB, the Red Baron™ Auxiliary PCB, and the Analog-Vector Generator PCB. Please mention this number whenever calling your distributor for service.
GAME SERIAL NUMBER MONITOR IDENTIFICATION TAG
AUXILIARY PCB e
REGULATORIAUDIO II PCB ANALOG VECTOR. GENERATOR PCB
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Published by: ATARI INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94085
Lithographed in the U.S.A. 6K
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1.) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
Table of Contents
Location Setup A. New Features B. Gamelnspection . C. Game Installation. ..
- Voltage Plug Selection ...
- Interlock and Power On/Off Switches . D. Self-Test Procedure ............005 E. Option Switch Settings .
- Bonus Play Feature. .
- Coin Mechanism Multipliers .
- Examples of Option Switch Settings . F. GamePlay .... 1, Attract Mode... 6. ccc cece e eee eens
- Ready-to-Play Mode .
- PlayMode ......... ;
- High Score Initial Mode .... 2.0.0.0. 0 ces e eee e eee e eee tees
Maintenance and Repair A. Cleaning... .. cece cence eee eee eee e tenet eee B. Fuse Replacement..... C. Opening the Control Panel ....
- LED-Start Switch Replacement .
- Joystick Maintenance and Repair . Monitor Removal ............655 Fluorescent Tube Replacement . Printed-Circult Board Removal . .
- Analog Vector-Generator and Auxiliary PCB Removal .
- Regulator/Audio li PCB Removal .............. G. Game Operation.......... 0.6 cece cece eee tenes mmo
IMustrated Parts Lists illustrations and parts lists begin on page .......-... 6. eee e eee eae OOWODRWWOA
List of Illustrations
Figure 1 Overview of Game... 2... 2 eee eee eee eee 2 Figure 2 Installation Requirements ...... 3 Figure 3 International Voltage Plug Selection . 4 Figure 4 Interlock and Power On/Off Switches 5
Figure 5 Location of Self-Test Switch, Volume Control and Option Switches ... 6 Figure 6 Self-Test Procedure 7 Figure 7 Game Option Settings 0 Figure 8 Game Price Settings. . 1
Figure 9 Coin Counter Option Settings ....... 66... cece cece cee eee eee Figure 10 Opening the Control Panel... . Figure 11A Joystick Maintenance and Repair Figure 11B Joystick Maintenance and Repair Figure 12 Monitor Removal
Figure 13 Fluorescent Tube Removal............. 00sec eee n cence eee eens Figure 14 Printed-Circuit Board Removal Figure 15 Power Distribution Figure 16 Signal Distribution
Illustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies ... Figure 18 Control Panel Assembly Figure 19 Gimbal-Type Joystick Assembly . Figure 20 Regulator/Audio Il PCBAssembly .........-0+-.0eee seen eee e eee 32
Figure 21. Red Baron™ Auxiliary PCBAssembly ..........-00 0. cece eee sees 34 Figure 22 Red Baron™ Analog Vector-Generator PCB Assembly Figure 23 Fluorescent Light Assembly one Figure 24 Power Supply Assemblies for X-Y Games .........02 00sec ee ee eee 42
Figure 25 American-Made Coin Door... 2.2.0... cece erence eee 44 Figure 26 —_British-Made Coin Door
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvaie, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska or Hawaii (408) 745-2300 = From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey 2s (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 0062-52155
vi
Location Setup
=> Derm
w
A. New Features
The Red Baron™ game has three new features. Even if you are familiar with Atari games, you should
These new parts, as well as all other major parts @ Game Circuitry. Atari’s 3-dimensional X-Y game in the game, are illustrated in Figure 1. Throughout circuitry has been expanded into two intercon- this manual, wherever one of these new parts is a) nected printed-circuit boards (PCBs)—the Red mentioned, you will see this symbol:
FLUORESCENT LIGHT
XY MONITOR
MONITOR SHIELD REAR ACCESS PANEL
GIMBAL-TYPE JOYSTICK CONTROL
SPEAKER ‘START SWITCH
CONTROL PANEL
AUXILIARY PCB
RED BARON™ . ANALOG VECTOR- GENERATOR PCB
POWER ON/OFF ‘SWITCH
POWER SUPPLY
REGULATOR: AUDIO Il PCB
The footstep must be installed for cabinet stability. Without the footstep, this game can tip over onto an aggressive player. Le pledestal doit &tre installé pour la stabilité de cabinet. Sans le piedestal, ce jeu pourrait se renverser sur un joueur enthousiaste.
Figure 1 Overview of Game
B. Game
Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
1, Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the rear access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors{in the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that ail plug-in integrated circuits on the game PCB are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black metal strain-relief plate in the wood slot at the bottom of the rear panel opening.
® Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Red Baron™ Analog Vector-Generator PCB, Red Baron Auxiliary PCB, Regulator/Audio I! PCB and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.
Cc. Game Installation
Figure 2 Installation Requirements
175 watts maximum 0 to 38°C (32 to 100°F) Not over 95% relative With footstep: 64 x 84% cm (25% X33% in.) Without footstep: 64 x 64 cm (2514 x 25% in.) 190 cm (74% in.) Power Temperature Humidity Space Required
Game Height
- Voltage Plug Selection This game has two possible power supplies: the domestic or international. The domestic power supply operates on one line voltage range: 105 to 135 VAC. The international power supply has four colored voltage selection plugs and operates on the line voltage of almost any country In the world.
Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored voltage selection plugs, make sure that the voltage selection plug on the power supply is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4), One is located behind the rear access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when either the door or panel is opened.
Check for proper operation of the interlock switches by performing the following steps: © Be sure the coin door and rear access panel are closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture. @ Slowly open the rear access panel. The monitor picture should disappear when the door is opened approximately 2.5 cm (1 inch). Close and lock this door and repeat this step with the coin door. @ If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.
Line Voltage Range 90-110 VAC (100) 105-135 VAC (120) 200-240 VAC (225) 220-260 VAC (240)
Figure 3
Fuse cover must be in place during game operation.
Voltage Selection Plug Color Violet Yellow Blue Brown
International Voltage Plug Selection
POWER ONIOFF SWITCH
Figure 4 Interlock and Power On/Off Switches
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor and the game speaker, no additional equipment is necessary. Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.
To run the self-test, follow the instructions outlined in Figure 6.
RED BARON ANALOG VECTOR-GENERATOR PCB
OPTION SWITCHES
VOLUME INCREASE: TURN CLOCKWISE
SELF-TEST SWITCH (EURO- PEAN GAMES) VOLUME CONTROL
Figure 5 Location of Self-Test Switch,
Volume Control and Option Switches
Figure 6 Self-Test Procedure
Results if Test Fails Results if instruction Test Passes
- Set self-test After about 10-12 sec- ‘switch to on position onds, the monitor (see Figure 5). displays the picture below. No sounds are produced.
DISPLAY OF COMPLETE CHARACTER SET
AVERAGE GAME TIME IN SECONDS.
LEFT COIN MECH RIGHT COIN MECH MULTIPLIER (CENTER MULTIPLIER MULTIPLIER IF YOU HAVE A 3-MECH DOOR)
SWITCH SWITCH TOGGLE 8 TOGGLE 1
PHOTO ABOVE SHOWS AN EXAMPLE ONLY RAM FAILURE is indicated by a sequence of 1 to 10 tones, You will hear a short low tone and a short flash on the LED start pushbutton for each good RAM chip, and a fong high tone accompanied by a long pulse on the start pushbutton for a failing RAM chip. The test stops with the first failing RAM-chip pair (example: J2 and H2 are a pair). To restart the sequence, press the reset pushbutton on the Red Baron™ Analog Vector- Generator PCB, or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with the table below. Example: four short low tones followed by a jong high tone indicates failure of RAM at location B2. Bad RAM Chip Location Long High Tone: on Analog Vector-Generator PCB: ist J2 2nd H2 3rd Az 4th At
5th B2 6th 81
7th c2 8th C1 ath D2 10th D1
ROM/PROM FAILURE is indicated by two columns of numbers on the left side of the Screen. The number in the left column indicates the location of the failing ROM/- PROM(s). Identify the bad ROM/PROM with the table immediately below. Ignore the hexadecimal numbers in the right column on the screen.
Displayed No.: Bad PROM Chip Location: _Printed-Circuit Board: BIC3 or F/H3* A3 or E3
FIH1 J K1 uM1 Nt pi** co*t* Auxillary PCB
- If this PROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **If this PROM is bad, self-test will not work (screen may be blank or may display “ garbage”). ***If you replace this part, you must erase this ROM before locking up the game (see instruction 5 in this self-test procedure). Otherwise the self-test will Continue to display 9. Analog Vector- Generator PCB OMVODRWNAD
MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner of the display. Math-box failure is explained in the Signature Analysis Procedure, on the Red Baron™ schematic Sheet 1, Side B. Identify the failure with the table below.
Displayed Letter Failure ‘i Time out error H Data error—high byte L Data error—low byte
[Selt-test is continued on next page]
Figure 6 Self-Test Procedure, continued
Results if Instruction Test Passes Results if Test Fails
| 2. | Activate start | As switch activates, | You will not hear a beep for the defective switch. |
switch, fire switch, you'll hear a beep. As slam switch, and switch deactivates, utility and coin you'll hear another switches.* beep.
| 3. | Move joystick | The lower left number | Incorrect progression of numbers indicates potentiometer harness wires were con- |
| forward and back- | on the screen will in- | nected incorrectly. No number change indicates potentiometer is bad or harness | |
| ward. | crease with backward | wires are loose. |
motion, and decrease with forward motion. (Ignore any flickering of numbers.)
| 4. | Move joystick to | The tower right |
the right and left. number on the screen will increase with rightward motion, and decrease with leftward motion.
- Erasing the High Score Table (optional) The current three highest scores are held in permanent memory, even if the game is unplugged. If you want to erase these scores, simultaneously press the start and fire buttons. The ERASING message at the center rig! played for several seconds, until the entire table i: data will also be erased.
- When satisfied with test, set selftest switch to off position. ht of the screen will then be disis erased. The average game time
“Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you are in self-test.
NY LAM XR
E. Option Switch Settings
- Bonus Play Feature Red Baron™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.
For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a
ai play. Therefore, players receive 3 plays for
1.00.
This bonus feature encourages players to insert More money than just the minimum 50¢ you could require for one game. Various other bonuses are available (see Figure 8).
- Coin Mechanism Multipliers The coin-door mechanisms for this game will accept about a dozen different denominations. The door has either two or three mechanisms that can accept the same or different denominations.
All recent Atari game PCBs identify the different mechanisms in a certain pattern. The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech ina 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.
[2se [st Jese} |f2se| |[]\$1
This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/x 4. (The left mech in a 3-mech door always has avalue of x 1—you cannot change its value.)
You can set these multipliers with toggles 3 thru 5 on the switch assembly at location M10 on the Red Baron Analog Vector-Generator PCB. For exact settings of these toggles, refer to Figure 8.
- Examples of Option
Switch Settings
Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location M10; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7, 8, and 9 provide “$” signs indicating Atari’s recommendations.
Figure 7 Game Option Settings When changing the options, verify proper results on the moni- To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Red Baron Analog Vector-Generator PCB is mounted in place. tor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the monitor screen during the self-test.
Toggle Settings of 8-Toggle Switch on Red Baron PCB (at P10) {TOP switch when PCB is in game)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
Off Off English $ On Off French
| of | On | Spanish |
| On | on | German |
Bonus airplane granted at:
| Off | Off | 2,000, 10,000 and 30,000 points | $ |
| Off | On | 4,000, 15,000 and 40,000 points | |
| On | Off | 6,000, 20,000 and 50,000 points | |
| On | On | No bonus airplanes | |
| Ott | Off | 2 airplanes per game | |
| Off | On | 3 airplanes per game | $ |
| On | Off | 4 airplanes per game | |
| On | On | 5 airplanes per game |
Off 1-play minimum $ On 2play minimum Off Self-adjusting game difficulty feature tumed off
| On | Self-adjusting game difficulty feature turned on | $ |
aR Airplanes per game:
| If self-adjusting game difficulty feature is | Bonus airplane granted at: | 2 | 3 | 4 | 5 |
| fia ‘on, the program a to maintain me | 2,000, 10,000 and 30,000 points | 90 | 405$ | 120 | 135 |
| following average game lengths {in seconds): | 4,000, 15,000 and 40,000 points | 5 | 90 | 405 | 120 |
| 6,000, 20,000 and 50,000 points | 60 | 75 | 90 | 105 | |
| No bonus airplanes | 45 | 60 | 75 | 90 |
$ Manufacturer's suggested settings
} XJ
Figure 8 Game Price Settings The white block below contains Atari's suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at with each situation (labels are on the following page). Use the location M10, on the Red Baron™ Analog Vector-Generator PCB label no. 6 (indicated with © only if you set toggle 7 at PCB (the CENTER switch assembly), switch assembly P10 to on.
50¢ PER PLAY
Bonus Bonus 2 plays No bonus $1.00 = 3 plays 3 plays
Straight 25¢ Door
25¢/$1.00 Door or 250/25°/$1.00 Door
25¢ PER PLAY
Bonus Bonus No bonus $.50 = 3 plays $1.0
| 87 | 6 | 5 | ||
| @ | of | of | of | off |
Straight 25¢ Door
| 4 | 3 | 2 | 1 |
| Off | Off | On | Off |
25¢/$1.00 Door or 25¢/25¢/$1.00 Door
ab]
| Figure | 8 | Game Price Settings, continued |
The switch settings below relate to options for game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Red Baron™ game on free play, or if you have German coin mechanisms in your door. To achieve bonus plays, all coins must be inserted before press- Ing the start button. The label no. 6 shown below should be used ‘only if you set toggle 7 at PCB switch assembly P10 to on.
Toggle Seitings of 8-Toggle Switch on Red Baron PCB (at M10). CENTER switch when PCB is in game
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
Off Off Free play
| Off | On | 1 coin* for 2 plays | |
| On | Off | 1coin* fort play | $ |
| On | On | 2 coins” for 1 play | |
| Off | Off | Right coinmech x 1 | $ |
| Off | On | Right coin mech x 4 | |
| On | Off | Right coin mech x 5 | |
| On | On | Right coin mech x 6 |
Off Left coinmech x 1 $ On Left coin mech x 2
Off Off Off Oft Off On Off On Off Off On On
On Off Off
On Off On
No bonus coins $ For every 2 coins* inserted, game logic adds 1 more coin* For every 4 coins” inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 2 more coins* For every 5 coins” inserted, game logic adds 1 more coin* For every 3 coins* inserted, game logic adds 1 more coin*
*in the U.S., a “coin” is defined as 25%. In Germany a “coin” is 1 DM.
$ Manufacturer's suggested settings
Game Pricing Labels
o Zs @@ 2 coins =1 play ATARI
e
| J. | @ | 1 coin = | 1 play |
AO @ @ 2 coins = 1 play ATARI 6000 4 coins = 3 plays eo @@ 2coins A 9 @@ 3 coins 008 @ 4 coins
© @@ 2 coins =1 play
A $1 coin =3 plays
(Susan B. Anthony coin)
O71 @ 1 coin = 1 play amr’ 2. play minimum (2 coins = 2 plays)
(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)
Figure 9 Coin Counter Option Settings
[These toggles determine which coin mechanisms activate which counters]
Toggle Settings of 4-Toggle Switch on Game PCB (L11) Two coin acceptors 4 3 2 1 in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game: Three coin acceptors in the coin door:
| On | On | Both acceptors activate all coin |
counters simultaneously.
| Off | On | Both acceptors activate 2 count- |
ers separately. zy 3 3
| 3 | 3 | On | Off | Both acceptors activate all coin |
counters simultaneously.
| Off | Off | Both acceptors activate 2 count- |
ers separately. $ Do not use this setting.
Do not use this setting.
Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate all coin counters simultaneously.
Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters separately. All 3 are same denomination and they activate all coin counters simultaneously.
Left and center acceptor activate one coin counter, right acceptor activates another coin counter.
Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3mech coin door.
Left, center and right acceptors activate 3 coin counters separately. $
$ Manufacturer's suggested setting
F. Game Play
Atari’s Red Baron™ game is a one-player game with an X-Y or vector-generator monitor. The game depicts a first-person’s view from a World War | biplane cockpit. The player’s goal is to destroy as many enemy biplanes, blimps, tanks, pillboxes, pytamids and buildings as possible.
Players can maneuver their airplanes with the joystick control. Moving the joystick in its four directions creates a sensation of diving, climbing, or banking to the left or right.
The game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.
- Attract Mode The attract mode begins when power is applied to the unit, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a play is paid for and accepted or when in self-test. In this mode, the monitor displays three possible pictures.
One of the pictures displays a typical game play sequence, with a view looking out of the airplane cockpit at the horizon and mountains below. The player's propellor is almost always visible at the center bottom of the screen during this phase.
Enemy biplanes swoop towards the player's airplane and eventually overtake it. The VALUE message at the top center of the screen indicates the current number of points a player can earn for shooting the enemy biplane. The value ranges from 10 to 300 points, and decreases as the enemy plane comes closer to the player.
Blimps also appear in this scene. The blimps, tanks, and pillboxes may be firing shells at the player. If hit, the player sees a bullet picture on the windshield, and the scenery spins around, indicating that the player has crashed.
The second picture displayed during this mode will only appear if no credits remain in the game. The screen shows the RED BARON banner pulled
by a piane traveling towards the left. The propellor usually at the bottom of the screen disappears during this phase.
The third picture shows the three to seven highest scores and their matching initials. \f you erase the special ‘‘permanent” memory (see Figure 6, Self- Test Procedure), then this table will not appear on the screen. The table is redeveloped from scores of subsequent games.
- Ready-to-Play Mode This mode begins when sufficient coins are accepted for a game. It ends when the START pushbutton is pressed. When this mode begins, the message PRESS START jlashes in the center of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
Operators may choose one- or two-play minimums by selecting one of the option switch settings on the Analog-Vector Generator PCB (see Figure 7, Game Option Settings). !f you select the two-play minimum and a player inserts enough money for only one play, the message 2 PLAYS MINI- MUM flashes on the screen until the required number of coins is inserted.
- Play Mode The play mode begins when the start pushbutton is pressed. The mode ends when the player's last airplane is lost.
Players can score various points for shooting the different objects; the point values for each are silkscreened on the control panel. As mentioned earlier in Section 1, Attract Mode, the value for enemy Planes can vary. Point values for all other objects remain fixed.
The game starts with a slow enemy biplane appearing on the screen; the first four planes are relatively passive. As game time progresses, the play: er’s biplane speed increases and the enemy planes become more evasive.
After four airplane “attacks”, the player will see various objects on the ground. Later on, to provide challenge, the tanks, pillboxes, and blimps will start shooting at the player. If the player gets a very high score, the planes themselves will finally start shooting at the player.
One of the new operator-selectable features of Red Baron™ is its self-adjusting game difficulty. Figure 7 shows the option switch settings that determine an average game time in seconds (displayed on the screen during self-test). The game program accumulates an average of the last 32 games’ lengths. If the accumluated average exceeds the operator-selected average, at the beginning of the next game the computer makes the play harder. The logic does so by increasing the speed of the player's airplane and enemy airplanes. In essence, this feature adjusts the difficulty to establish a consistent average game time.
The average is stored in the non-volatile memoty—as are the top three scores on the high score table. Therefore, if you select this game difficulty option, you need not worry that the average will be “lost” if you turn off the game each night.
- High Score Initial Mode At the beginning of this mode, player instructions appear near the upper center of the screen, and A____ appears below them. Players enter initials one character at a time.
Pressing the fire button a third time causes the initials and game score to transfer to the high score table. This table contains a maximum of seven scores and appears during the attract and ready-toplay modes.
Maintenance and Repair P
& All games require certain maintenance to keep them in good working order. Clean, properly maineae tained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if the gimbal-type joystick control or light-emittingdiode switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the joystick control— for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.
B. Fuse Keplacement
This game contains five fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 24 of this manual. See the Quadrascan monitor manual, TM-146, for the monitor fuse data.
C. Opening the
Control Panel
Prior to repairing or replacing any item on the control panel, unplug the game. Then open the coin door. Reach through the opening and remove all three sets of carriage bolts, wing nuts, flat and lock washers, located on the underside of the contro! panel (see Figure 10). Lift up on the control panel, and tilt it towards you.
- LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
@ Remove the wires from the suspected switch. ® Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. ®@ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
TO REMOVE LED SWITCH: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise (as viewed from inside of control panel) while holding the black cone-shaped nut on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.
COMMON J CONTACT LIGHT-EMITTING-DIODE (L.E.D) CONTACTS
NORMALLY OPEN (N.O.) CONTACT
NORMALLY CLOSED (N.C.) CONTACT
Figure 10 Opening the Control Panel
LED { VIOLET CONTACTS RED
START SWITCH HARNESS YELLOW TO N.O. GREEN TO GROUND FIRE SWITCH | BLACK TO COMMON
VERTICAL POTENTIOMETER
HORIZONTAL ORANGE | POTENTIOMETER
Figure 11A Joystick Maintenance and Repair
- Joystick Maintenance and Repair Normal maintenance involves lubricating four paris in the joystick control approximately every three months (this requires removing the control). First open the control panel as described previously.Then unplug the “quick-disconnect” connectors on the two potentiometers, as well as the connector for the fire switch.
From the inside of the control panel, remove the four flat and lock washers, hex nuts and carriage bolts that mount the joystick onto the control panel.
Then open up the joystick control assembly by removing the four flat washers, hex nuts, and long screws (see Figure 11B). At this point, most of the parts should become disassembled.
For lubrication, use only Nyogel 779 lubricant (Atari part no. 178027-001). Lubricate the following parts inside the control: @ The ball pinned to the shaft and the ends of the pivot pins that protrude from the ball. @ The insides of the two black linkages, located on the potentiometer shafts. @ The insides of the two gimbals, where the bottom of the shaft wears against them. @ The four holes on the sides of the pivot ball housings, where the gimbals are attached.
To replace the bellows, remove both gimbals and the bellows cap. Slide the bellows off the bottom of the shaft and over the harness wires. Slide the new bellows up over the harness and shaft.
Reassemble the joystick control, and then rein- Stall it in the control panel. Reconnect the harness wires as shown in the Figure 11A: make sure the right colors go to the tabs on the potentiometers and the fire switch.
Repairs on the contro| handle would probably only involve replacement of potentiometers, the fire switch or the centering bellows.
PIVOT BALL: HOUSINGS,
‘LINKAGES LUBRICATE HERE LUBRICATE HERE “ (4 PLACES) we
CENTERING BELLOWS
‘BELLOWS CAP
INNER GIMBAL OUTER GIMBAL
TIE-WRAP
RS LUBRICATE HERE
‘SLEEVING!
Figure 11B Joystick Maintenance and Repair
D. Monitor Removal
If you should need to remove the Quadrascan X-Y monitor, follow steps 1 thru 7 as listed on this page. Refer to Figure 12 below. 7. Open the rear access panel. Be sure the game is unplugged from its wall outlet! Remove the middle and bottom retainers at the front of the game. Set aside the attraction panel. Then remove the acrylic monitor shield by pulling its upper edge out. Working up from the bottom side corners, carefully pry loose the two side flaps of the colorful 2-piece cardboard bezel. (A 4-inch strip of double-sided adhesive tape is centered behind both side flaps, flush with each edge.) Remove the bezel as a complete unit—do not remove the smaller part first. Unplug the monitor harness connector underneath the monitor. Remove the four sets of carriage bolts, flat and split lock washers, and self-locking hex nuts that hold down the metal chassis of the monitor. These are underneath the monitor shelf. Carefully slide the monitor chassis out the front of the game.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 12 Monitor Removal
Figure 13 Fluorescent Tube Removal
E. Fluorescent Tube
Keplacement 1. Remove the six Allen-head screws and lock
washers that secure the middle and top retainers at the front of the game. Set aside the at-
- Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an imit will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.
To replace the white fluorescent tube behind the Plosion! front graphics attraction panel, follow this pro- 4. Reconnect the Y-shaped connectors, Reinstall cedure (see Figure 13): the attraction panel and its two retainers.
F. Printed-Circuit Board Kemoval
You may wish to remove the Red Baron Analog- Vecior Generator printed-circuit board (PCB), Auxiliary PCB, or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 14 and proceed as follows:
- Analog Vector-Generator and
Auxiliary PCB Removal
@ Open the rear access panel. @ Unplug the 24-pin PCB interconnector from the Auxiliary PCB or the Analog Vector-Generator PCB (whichever board you are removing). @ Remove the 44-pin edge connector from the right side of the PCB. @ Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove and save this screw as well as the fiber washer. @ Remove the PCB from the cabinet by carefully pulling it straight out of the plastic PCB retainer. id Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage the PCB and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you replace a PCB.
Regulator/Audio li PCB Removal Unlock and open the rear access panel. Remove the five plug-in connectors on the Regulator/Audio II PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the two fiper washers. Remove the PCB from the interior wall of the cabinet.
REGULATOR/ AUDIO Il PCB
Figure 14 AUXILIARY PCB
*
ANALOG VECTOR. GENERATOR PCB
Printed-Circuit Board Removal
G. Game Operation
With this manual you received three large sheets that contain the wiring and schematic diagrams for the Red Baron™ (upright) game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They include explanations. of the functions of the circuits; the diagrams also define inputs and outputs.
Atari’s Red Baron is a microprocessor-controlled game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch and potentiometer inputs from the control panel and coin door. These inputs are processed by the Analog Vector-Generator PCB and output to the monitor, RegulatoriAudio Il PCB, and control panel.
The monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. The Regulator/Audio Il PCB performs two functions: 1) it regulates the voltages from the power supply to +5 VDC and + 12 VDC, and 2) it amplifies the audio output from the Auxiliary PCB.
Specifically, the +5 VDC from the Regulator/- Audio {1 PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCBs; + 22 VDC is regulated on the Analog Vector-Generator PCB to produce +15 and +5 VDC (the latter for the digitalto-analog converters); and + 22 VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio I! PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.
The power supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis (F3-F6). The primary winding of the power-supply transformer is protected by the fuse in the separate fuse post on the power-supply chassis (F1).
Figure 14 illustrates the distribution of power in this game. Figure 15 illustrates the distribution of signals. =
ww
FLUORESCENT, LIGHT
MONITOR
CONTROL PANEL
AUXILIARY PCB
ANALOG VECTOR- GENERATOR PCB
SAFETY INTERLOCK ‘SWITCH
LINE VOLTAGE
‘ON/OFF SWITCH
POWER SUPPLY
REGULATORI/AUDIO II PCB’
Figure 14 Power Distribution
CONTROL PANEL,
COIN DOOR
VOLUME CONTROL’
REGULATOR/AUDIO li PCB MONITOR
SPEAKER
Zour
AUXILIARY PCB
ANALOG VECTOR- GENERATOR PCB
Figure 15 Signal Distribution
Illustrated Parts Lists
This chapter provides you with the necessary information for ordering replacement parts for your Red Baron™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results wiil be less downtime and more profit from your game.
Fluorescent Light— see Figure 23 037576-01 (Retainer)
037577.01. (Retainer)
037571-01 Schematics, Self-Test Label & Manuals— see parts list on following page
037080-01 (Mon. Overlay) A036138-01 oa7s6a01 (Cab. Assy.)
(Attract. Panel) 02-305010 ‘{T-Molding)
A037559-01 (Housing) (Mon. Shield),
92-047 ot -050, 01 XY Monitor) N20 037578-01 iron (eek) (Retainer) _ 03612601 (Rear Panel) Joystick Assy.— see Figure 19.
| (Speaker) | a | 03574503 |
(epaeich (10-In. PCB Retainer) Control Panel Assy.— A036243-01
| see Figure 18 | oasr. | (Main Harness) | |
| 036130-01 | (18-In, PCB Retainer) | : | 03453603 |
| (Spkr. Grille) | 4 | (Viora. Damper) |
03612402 i
| i | : | Auxiliary | PCB— | |
| Pal | (Coin Defletr, | ; | : | hal ay Po 7 |
03016801 A036247-01 (Vol. Ctrl. Brkt.) (PCB Interconnector) (Inter. Sw.) Coin Doors— ‘Analog Vect.-Gener. PCB— see Figures 25, 26
| berese02) | ; | 5 | see Figure 22 |
(Interl. Sw. Cover)
| A036943-01, .02 or -03 | 5 | : | 009992.01 |
(Coin Box) "pace L (On/Oft Sw. Cover)
Reg/Audio Il PCB 61-1624 (on/off Sw) 006450-01 (On/Off-Sw. Plate) 78-6HO02" (Matting)
A034841-03, NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ‘A036260- A034863-03 or CONMBENTIAL: Reproduction forbdogn withont tne ape id Power Supply Assy.— A035989-03 Gific written permission of Atari, Inc., Sunnyvale, CA. This (Footstep Assy.) see Figure 24 drawing is only congitionally issued, nelther receipt nor (Power Cord) possession thereof conters or transfers any right in, or I Sense to use, the subject matter of the drawing or any de- Sian or Iechnical Infomation shawn threon, nor any ght {0 reproduce this drawing or any part thareet, Exc manufacture by vendors of tat nt. and for manufacture under the corporation's written lice to reproduce this drawing or the sul {ess by written aproement vith or written permission from he corporat
Figure 17 Cabinet-Mounted Assemblies A037558-01 A
Figure 17 Cabinet-Mounted Assemblies Parts List
Part No. Description
| A034841-03 | Strain-Relief Power Cord | (U.S.) |
| A034863-03 | Strain-Relief Power Cord | (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, |
Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A035943-01 | Deep-Well Coin Box Assembly | (for all the same coins) |
A035943-02 Deep-Well Coin Box Assembly (for two different coin denominations—has one separator) A035943-03 Deep-Well Coin Box Assembly (for three different coin denominations—has two separators) A035989-03 Strain-Relief Power Cord (Australia and New Zealand) A036138-01 Cabinet Assembly (inc/udes legs and PCB retainers, but not the rear access panel) A036189-01 Interlock Switch Assembly (modified for safety) A036243-01 Main Harness Assembly A036245-01 Fluorescent Light Harness (at upper rear of game) A036247-01 Printed-Circuit-Board Interconnector A036260-01 Footstep Assembly (includes rubber matting) A037559-01 Wood Housing Assembly The following seven items are the technical information supplements to this game: DP-169-01 Red Baron™ (Upright) Schematic Drawings (Sheet 1)
| DP-169-02 | Red Baron Schematic Drawings | (Sheet 2) |
| DP-169-03 | Red Baron Schematic Drawings | (Sheet 3) |
ST-169 Red Baron Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for Electrchome G05-802/805 Quadrascan™ X-Y Monitor TM-164 Service Manual for Wells-Gardner Quadrascan X-Y Monitor TM-169 Red Baron Operation, Maintenance and Service Manual 02-305010 %-Inch Black Plastic T-Molding 19-9032 Volume Control 61-162A DPST Power On/Off Toggie Switch
| 71-2110 | Panel Cartridge Lock Mechanism | (for rear access panel) |
7507017 Spacer for Mounting Printed Circuit Boards
| 78-24012 | 5-Inch Beaded Nylon Tie Wrap | (for PCB edge connectors) |
78-3201 Cabinet-Leveling Leg 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, % inch wide x inch thick (for bottom retainer— 24 in. required) 78-6H002 1/8-Inch-Thick Corrugated Rubber Matting for Footstep (14% x 23% inches are required) 92-047 19-Inch Quadrascan™ X-Y Electrohome Monitor 92-050 19-Inch Quadrascan X-Y Wells-Gardner Monitor 006450-01 On/Off-Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030168-01 Volume Contro! Bracket
| 034536-03 | Foam Vibration Damper | (for Auxiliary and Analog Vector-Generator PCBs) |
035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer 035942-01 Deep-Well Coin Box Separator 03612402 Cardboard Coin Deflector 036126-01 Rear Access Panel (does not include lock) 036130-01 Speaker Grille 036262-01 Coin Box Bracket 037090-01 Blue Monitor Overlay with Foam Tape [Continued on following page]
Figure 17 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description
037569-01 “Red Baron” Attraction Panel with Graphics 037571-01 Monitor Shield with Graphics 037573-01 Left Side-Panel Decal 037573-02 Right Side-Panel Decal 037576-01 Top Retainer (for attraction panel) 037577-01 Middle Retainer (for attraction panel and monitor shield) 037578-01 Bottom Retainer (for monitor shield) 037581-01 Cardboard Bezel with Graphics 148001-001 6x9Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker
(LED Spacer)
75-9910WO {Stamped Nut)
78-6900402° (Foam Tape)
A037666-01 (Harness)
ce
1 ae
{ asl A037579-01 033127-01 (Sw. Bushing) (Ctrl, Panel)
Figure 18 Control Panel Assembly A037582-01 A
Parts List
Part No. Description
A037579-01 Controi Panel with Graphics A037666-01 Control Harness Assembly 62-039 Momentary-Contact SPDT Light-Emitting-Diode Switch with Red Cap 75-07054 Nylon Spacer for Light-Emitting-Diode Switch 75-9910WO #15/32-32 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, 1/8-inch thick x %4-inch wide (24 in. required) 033127-01 Black Molded Switch Bushing
178027-001 (Lubricant— not shown) (oN 72-8614 72-5240 (Screw) (Screw) 036276-01 Q~ (Bezel) ow . 62.043 036953-01 ‘ (Plate) (Switch)
036961-01 (Shaft) 036279-03 \ A036958-01 (Pivot Ball) ¢ (Shaft Assy.) 73-2232 , 035995-01, -02 in) 2 (Ctr, Handle)
036963-01 036952-01 (Slide Plate) (Housing)
036954-01 (Mount, Plate)
A036281-02 (Bellows)
036955-01 ‘ (Cap) ; (Screw)
75-0108: (Washer)
19-9026 (Resistor) 75-9408: (Hex Nut)
036956-02 (Outer S602 — |
036956-01 (Inner Gimbal) 036957-01 75-07020 (Linkage) (Washer)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: ‘Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw: ing or any design or technical information shown thereon, ‘nor any right to reproduce this drawing or any part there: of. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation’s written license, fo right to reproduce this drawing is granted or the sub: ject matter thereof unless by written agreement with or written permission from the corporation.
Figure 19 Gimbal-Type Joystick Assembly A036951-01 A
Figure 19 Gimbal-Type Joystick Assembly Parts List
Part No. Description A036281-02 Centering Bellows A036958-01 Shaft Assembly with Fire Switch Harness (includes pivot ball, pivot shaft and slotted pin) 035995-01 Control Handle (right half) 035995-02 Control Handle (left half) 036276-01 Bezel for Fire Pushbutton 036279-03 Pivot Ball 03695201 Pivot Ball Housing (two of these required per handle) 036953-01 Square Control Plate 036954-01 Mounting Plate 036955-01 Bellows Cap 036956-01 Inner Gimbal 036956-02 Outer Gimbal 036957-01 Gimbal Linkage 036961-01 Pivot Shaft 036963-01 Slide Plate 19-9026 5K Ohm, + 20%, 2%4W Variable Resistor 62-043 SPST Pushbutton Switch with Red Non-Lighting Cap (used as fire switch) 72-5240 #10-32 x 2¥2-Inch Hex-Head Steel Machine Screw 72-8406 #4-40 x 3/8-Inch Hex Cap-Head Steel Machine Screw 72-8614 #6-32 x 7/8-Inch Hex Socket-Head Steel Machine Screw 73-21232 3/16-Inch Diameter x 2-Inch Long Siotted Pin 75-0108. #10 Zinc-Plated Steel Flat Washer 75-07020 3/8-Inch Flat Washer 75-940S #10-32 Steel Self-Locking Polymer Hex Nut 178027-001 Nyogel 779 Lubricant
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproducti
cific written permission
drawing is only conditionally issued,
possession thereof confers or transfers any right in, oF l-
‘Gense to use, the subject matter of the drawing or any de
‘sign or technical information shown thereon, nor any right
to reproduce this drawing or any part thereof. Except tor ture by vendors of At. and for manufacture
jon's writer is granted or the subject matter thereof fn agreement with or written permission
from the corporation.
A035435-02 D ‘0
R527,
ic 3300 35V
C18 3301 38"
TIP 32. Ejaz
753] R4 NAO CR4
33IR3 Be
Baty Alec ar
C22 Rishox
3300uF 440 5Wb sas 7812
C7 oD COD
ror C23 eiaF
TDAZO02 A 02 arr
Rid |O'
He an a0 ad
+
co R24, 10,,7W}— cal
=) 0g R3i
Figure 20 Regulator/Audio Il PCB Assembly clo 3300uF +h-— S35V. ID g il 22.0,10W
7905
Re2poa) a 220] R21 Cle coop!
cl4 oO
TDAZOO2A arte
Lew
Figure 20 Regulator/Audio ll PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 12-52P7 | 2.7 Ohm, +5%, 1W Resistor | (R5) |
16-54PO 40Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 -1 Ohm, +3%, 7W Wirewound Resistor (R24)
| 19-315102 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot | (R8) |
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C4, 4, 12) |
| 24-350226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C24, 31) |
| 24-350338, | 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C9, 10, 18, 19) |
24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088. .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CR1, 4-8)
| 31-5401 | 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode | (CR 5-8) |
33-TIP32 PNP Power Transistor, Type TIP32_ (Q2)
| 34-2N3055 | NPN Silicon Transistor, Type 2N3055 | (Q3) |
37-LM305 5V Linear Voltage Regulator (Q1)
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | —5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x ¥a-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405, #6-32 x V4-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
78-16014 Thermally Conductive Silicon Insulator (Q2, 9)
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Recepiacie | (J7) |
| 79-58346, | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 100015-103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C5, C14) |
110000-010 1 Ohm, +5%, %W Resistor (R10, 19) 110000-100 10 Ohm, +5%, %W Resistor (R11, 20, 29, 30)
| 110000-101 | 100 Ohm, +5%, %4W Resistor | (R4, 12, 22) |
110000-102 1K Ohm, +5%, %W Resistor (R27, 28)
| 110000-103 | 10K Ohm, +5%, %W Resistor | (R13, 14) |
110000-271 270 Ohm, +5%, %W Resistor (R1) 110000-330. 33 Ohm, +5%, %4W Resistor (R3)
| 110000-392 | 3.9K Ohm, +5%, %4W Resistor | (R6) |
| 110000-562 | 5.6K Ohm, +5%, %W Resistor | (R32, 33) |
| 110000-752 | 7.5K Ohm, +5%, %W Resistor | (R7) |
110001-221 220 Ohm, +5%, /2W Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16)
| 122004-224 | .22 uf Ceramic-Disc 25V Capacitor | (C6, 8, 15, 17) |
| 137151-002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. this drawing is only ‘conditionally’ issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing orany design or echnical information shown thereon, nor-any right fo. reproduce this drawing or_any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereo! unless by written agreement with or written permission from the corporation.
15} RO ee eS ae si iA . oer as2 [- ° v AE Re! ae 323 0 zy Raz an ORR] a ass Bed Ly (EE 2Se ‘oer R57
b QS os terzed] g LES
z a < wor > 1k Oe lo-rezzICs 1e0--OOLE! Ioo-PooLE! 1GO-OOLE!
T TAR @D We a or
€ oe ee
v ZB aaa = +] ZEST] Z pest past = ee]
¢ a a
or = Figure 21 Red Baron™ Auxiliary PCB Assembly A036305-01 B+
Figure 21 Red Baron™ Auxiliary PCB Assembly --) Parts List
Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio VO N-Channel MOS/LSI Custom Chip (B2)
| 12-5821 | 820 Ohm, +5%, 1 W Resistor | (R39) |
21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C8) 24-101104 -1uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C21, 22, 32} 21-101153. 015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C12) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C30, 50, 52) 24-250107 100 uf Aluminum Electroiytic Fixed Axial-Lead 25V Capacitor (C46) 24-250226 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C5) 24-250476 47 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C53) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C35, 43) 24-350106 10 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C54) 24-350476 47 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C53) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C36, 37, 51) 28-101101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C27) 29-006 1 uf, +10%, 35V Tantalum Capacitor (C48) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-4, 6, 7, 9-11, 14, 18-20, 23, 25, 26, 28, 29, 31, 33, 38, 39-42, 44, 45, 49, 55, 56) 31-1N100 100V Type-1N100 Switching Diode (CR6, 7) 31-1N914 75V Type-1N914 Switching Diode (CRI1, 2, 4) 32-1N5235, 6-8V 500mW Type-1N5235 Zener Diode (CRS) 34-2N3643 60V 300mW Type-2N3643 NPN Transistor (Q1, 2)
| 37-LM324 | Type-LM324 Integrated Circuit | (K4, K5) |
37-1408 Type-1408 Digital-to-Analog-Converter Integrated Circuit (B4) 37-4066. Type-4066 Analog Switch Integrated Circuit (J5)
| 37-555 | Type-655 Timer Integrated Circuit | (JO, K2) |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (A4, J4) |
| 37-74LS02 | Type-74LS02 Integrated Circuit | (D3, C5) |
| 37-74LS04 | Type-74LS04 Integrated Circuit | (D5) |
| 37-74LS08 | Type-74LS08 Integrated Circuit | (F3) |
| 37-74LS32 | Type-74LS32 Integrated Circuit | (C4) |
| 37-74LS74 | Type-74LS74 Integrated Circuit | (D4) |
| 37-74LS139 | Type-74LS139 Integrated Circuit | (B5) |
| 37-74LS161 | Type-74LS161 integrated Circuit | (C1, D1) |
| 37-74LS164 | Type-74LS164 Integrated Circuit | (E4, F4) |
| 37-74LS174 | Type-74LS174 Integrated Circuit | (AQ) |
| 37-74LS175 | Type-74LS175 Integrated Circuit | (HO) |
| 37-74LS191 | Type-74LS191 integrated Circuit | (A3, B3) |
| 37-74LS244 | Type-74LS244 Integrated Circuit | (EQ) |
| 37-74LS273 | Type-74LS273 Integrated Circuit | (E3) |
37-74LS374 Type-74LS374 Integrated Circuit (FO, B1)
| 37-74S08 | Type-74S08 Integrated Circuit | (K3) |
| 37-74109 | Type-74109 integrated Circuit | (C3) |
37-7815 +15V Voltage Regulator (VR2) 37-7915 — 15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Red Light-Emitting Diode (CR3) [Continued on next page]
Figure 21 Red Baron™ Auxiliary PCB Assembly, continued Parts List
Part No, Description (Reference Designations and Locations in Bold) 41-3003, 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1-4)
| 79-42016 | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | (A1, A5, E1, F1, H1, J4, K1, L1) |
| 79-42C22 | 22-Contact Medium-Insertion-Force Integrated Circuit Socket | (C0) |
| 79-42C40 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | (B2, C/D2, E2, F/H2, J2) |
81-4302 Nylon Snap-In Fastener 020670-01 Test Point
| 036174-01 | Programmable Read-Only Memory | (A1) |
| 036175-01 | Programmable Read-Only Memory | (E1) |
| 036176-01 | Programmable Read-Only Memory | (F1) |
036177-01 Programmable Read-Only Memory (H1)
| 036178-01 | Programmable Read-Only Memory | (J1) |
| 036179-01 | Programmable Read-Only Memory | (K1) |
| 036180-01 | Programmable Read-Only Memory | (L1) |
| 036464-01 | Programmable Read-Only Memory | (A5) |
100015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C34) 110000-102 1K Ohm, +5%, %W Resistor (R1, 4, 12, 17, 19, 21-23, 33, 37, 43, 64-72) 110000-103 10K Ohm, +5%, %W Resistor (R7-9, 11, 31, 32, 46-63) 110000-104 100K Ohm, +5%, %4W Resistor (R29)
| 110000-151 | 150 Ohm, +5%, V4W Resistor | (R35, 44) |
110000-152 1.5K Ohm, +5%, %4W Resistor (R34) 110000-153 15K Ohm, +5%, %4W Resistor (R27) 110000-221 220 Ohm, +5%, %4W Resistor (R20) 110000-222 2.2K Ohm, +5%, %W Resistor (R16, 40) 110000-223 22K Ohm, +5%, YW Resistor (R28, 36, 38) 110000-273 27K Ohm, +5%, %4W Resistor (R30)
| 110000-333 | 33K Ohm, +5%, Y4W Resistor | (R6, 26) |
110000-334 330K Ohm, +5%, %W Resistor (R25) 110000-391 390 Ohm, +5%, %4W Resistor (R45) 110000-392 3.9K Ohm, +5%, %W Resistor (R15) 110000-471 470 Ohm, +5%, %W Resistor (R13, 41, 42) 110000-473 47K Ohm, +5%, YW Resistor (R2) 110000-562 5.6K Ohm, +5%, %4W Resistor (R5, 10, 18)
| 110000-681 | 680 Ohm, +5%, %W Resistor | (R24) |
110000-683 68K Ohm, +5%, %4W Resistor (R3) 110000-822 8.2K Ohm, +5%, %4W Resistor (R14) 122000-225 22 uf, +20%, 35V Tantalum Capacitor (C47) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C13, 15-17, 24)
| 137002-001 | Type-74S86 Integrated Circuit | (H4) |
| 137003-001 | Type-74S03 Integrated Circuit | (J3) |
137004-001 Transistor Array (C/D2, E2, F/H2, J2) 137161-001 Read-Only Memory (C0) Note: If you replace this part, you must erase this ROM before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. If you do not erase the ROM, the self-test wili show the ROM to be “defective” by displaying the number 9 on the screen. 179010-001 12-Pin PCB Header (J16, J17)
» ia
° f LI
| fy | iN | [FI | Z | ) EE] | rR] |
| ~ (8d | © OSE | A | ol | Bo | H 80 |
| cee | SS | = | LS |
= -
| “HO | 8 | G0 oO Gell Del © | ie | |
| o | om | LSS | ||
| F | 7 | a | oe | |
| -/ | GH | © QSCHMEA Bled | 0 | Weze. |
| © | 8 | Fy | Am | ae |
~ POH Wl Woee E weh Tg ue
- H Hl
o
NOTICE TO ALL FERSONS RECEIVING THIS: 3 CONFIDENTIAL: Reproduction forbidden with-
granted or the sut ° written agreement with or written permission from the corporation
Figure 22 Red Baron™ Analog Vector-Generator PCB Assembly A037544-01 A
Figure 22 Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) [A035742.02, Rev. C+] 19-007 10K Ohm, + 20%, 1%4W 8-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations E6, F6, H6) 19315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R73, 74) 21-101102 .001 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94) 21-101103 01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C103)
| 24-250106 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C17, 18) |
| 24-250107 | 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C78, 83-86) |
| 24-500105 | 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor | (C30, 89, 90) |
| 27-102182 | .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor | (C105) |
| 28-101100 | 10 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor | (C44) |
| 28-101101 | 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C27) |
| 28-101151 | 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C63) |
| 28-101221 | 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C82) |
| 28-101390 | 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C25, 64, 106) |
| 28-101470 | 47 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C104) |
29-006. 1 uf, +10%, 35V Tantalum Capacitor (C88) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-39, 42, 43, 45, 46, 50-54, 61, 72-77, 79-81, 97, 98)
| 31-1N100 | 100V Type-1N100 Switching Diode | (CR11) |
| 31-1N914 | 75V Type-1N914 Switching Diode | (CRI, 3-10) |
| 33-2N3906 | Type-2N3906 PNP Switching and Amplifying Transistor | (Q3, 7) |
34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q4-6)
| 37-LM319 | Type-LM319 Integrated Circuit | (B12, D12) |
| 37-TLO82CP | Type-TL082 Integrated Circuit | (A10, D10) |
| 37-13201 | Type-LF13201 Integrated Circuit | (B10, D11, £10) |
| 37-347 | Type-TL084 Integrated Circuit | (C11) |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (J4) |
| 37-74LS02 | Type-74LS02 Integrated Circuit | (N9, M7) |
| 37-74LS08 | Type-74LS08 Integrated Circuit | (L5, P8) |
| 37-74LS10 | Type-74LS10 Integrated Circuit | (K4) |
| 37-74LS14 | Type-74LS14 Integrated Circuit | (B6) |
| 37-74LS20 | Type-74LS20 Integrated Circuit | (M5) |
| 37-74LS27 | Type-74LS27 Integrated Circuit | (N7) |
[Continued on next page]
Figure 22 Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) [A035742-02, Rev. C+] 37-74LS32 Type-74LS32 Integrated Circuit (J5, K10, M8) 37-74LS42 Type-74LS42 Integrated Circuit (B4, J7) 37-74LS74 Type-74LS74 Integrated Circuit (H10, L10, M9) 37-74LS86 Type-74LS86 Integrated Circuit (D7) 37-74LS109 Type-74LS109 Integrated Circuit (N8) 37-74LS139 Type-74LS139 Integrated Circuit (C4, K5, L2, M2) 37-74LS157 Type-74LS157 Integrated Circuit (D4, E4, F4, H4) 37-74LS161 Type-74LS161 Integrated Circuit (K6, L4, L6, M6, N6) 37-74LS164 Type-74LS164 Integrated Circuit (P9) 37-74LS174 Type-74LS174 Integrated Circuit (C7, L7, M11) 37-74LS175 Type-74LS175 Integrated Circuit (F8, F9, J8, K8) 37-74LS191 Type-74LS191 Integrated Circuit (F10, J6) 37-74LS193 Type-74LS193 Integrated Circuit (E5, F5, H5) 37-74LS194 Type-74LS194 Integrated Circuit (A5, A6, B5, C5, D5, D6) 37-74LS244 Type-74LS244 Integrated Circuit (K3, N2, P2, N11, P11, R11) 37-74LS245 Type-74LS245 Integrated Circuit (F2, R4/5, R5) Acceptable substitute is part no. 37-8304B. 37-74LS273 Type-74LS273 Integrated Circuit (C8) 37-74LS367 Type-74LS367 Integrated Circuit (F7, H7) 37-74LS393 Type-74LS393 Integrated Circuit (M4, N5) 37-74LS399 Type-74LS399 Integrated Circuit (H8) 37-74LS670 Type-74LS670 Integrated Circuit (E6, F6,H6) Acceptable substitute is part no. 37-74LS170. 37-74S00 Type-74S00 Integrated Circuit (C6) 37-74S02 Type-74S02 Integrated Circuit (K9) 37-74S804 Type-74S04 integrated Circuit (K2, R9) 37-74874 Type-74S74 Integrated Circuit (J10, L9) 37-74S260 Type-74S260 Integrated Circuit (L8) 37-7404 Type-7404 Integrated Circuit (H11) 37-74193 Type-74193 Integrated Circuit (N4) 37-7805 +5V Voltage Regulator (VR2) 37-7815 +15V Voltage Regulator (VR3) 37-7915 - 15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR2) 41-3004 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1) Acceptable substitute is part no. 41-3003. 62-001 SPST Momentary Pushbutton Switch (SW1) 66-114P1T 4Station Single-Throw, Dual-Inline-Package Bit Switch (L11) 66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (M10, P10) 79-42024 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, Ji, J3, K1, M1, N14, P1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (L/M/N3) 81-4302 Nylon Snap-In Fastener 90-102 12.096 MHz, + .005%, Crystal (¥2) 90-6013 Microprocessor (LIM/N3) 90-7033 Random-Access Memory (A1, A2, B1, B2, C1, C2, D1, D2, H2, J2) 020670-01 Test Point 036408-01 Programmable Read-Only Memory (K7)
Figure 22 Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) [A035742-02, Rev. C+]
| 036995-01 | Read-Only Memory | (N1) |
| 036996-01 | Read-Only Memory | (U/M1) |
| 036997-01 | Read-Only Memory | (K1) |
036998-01 Read-Only Memory (J1)
| 037000-01 | Read-Only Memory | (E1) |
| 037006-01 | Read-Only Memory | (B/C3) |
| 037007-01 | Read-Only Memory | (A3) |
| 037587-01 | Read-Only Memory | (F/H1) |
100015-103 .01 uf Ceramic-Dise Minimum 25V Radial-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100) 110000-101 100 Ohm, +5%, %4W Resistor (R70, 75) 110000-102 1K Ohm, +5%, %W Resistor (R18, 20, 27, 67, 84-86, 94, 110, 128-133) 110000-103 120 Ohm, +5%, %4W Resistor (R9-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 125-127) 110000-104 100K Ohm, +5%, %W Resistor (R35-42) 110000-122 1.2K Ohm, +5%, %4W Resistor (R46)
| 110000-151 | 150 Ohm, +5%, %4W Resistor | (R103) |
| 110000-153 | 15K Ohm, +5%, YW Resistor | (R93) |
110000-221 220 Ohm, +5%, %W Resistor (R24) 110000-222 2.2K Ohm, +5%, YW Resistor (R45, 92, 102, 112, 114-116, 119-121, 123) 110000-223 22K Ohm, +5%, %W Resistor (R28-32) 110000-270 27 Ohm, +5%, %4W Resistor (R111) 110000-332 3.3K Ohm, +5%, %W Resistor (R87, 97) 110000-392 3.9K Ohm, +5%, %4W Resistor (R47, 49) 110000-471 470 Ohm, +5%, %W Resistor (R34, 104-109) 110000-472 4.7K Ohm, +5%, Y4W Resistor (R43)
| 110000-474 | 470K Ohm, +5%, %W Resistor | (R113, 117, 118, 122) |
110000-561 560 Ohm, +5%, %4W Resistor (R96)
| 110000-562 | 5.6K Ohm, +5%, %4W Resistor | (R99) |
110000-680 68 Ohm, +5%, %4W Resistor (R124)
| 110000-681 | 680 Ohm, +5%, YW Resistor | (R83) |
110000-821 820 Ohm, + 5%, %W Resistor (R68, 69, 82) 110003-752 7.5K Ohm, + 1%, W Metal-Film Resistor (R71, 72, 76-81, 89) 121007-473 .047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Polycarbonate Capacitor (C56, 59) 122000-225, 2.2 uf, + 10%, 35V Tantalum Capacitor (C87)
| 137002-001 | Type 74S86 Integrated Circuit | (B7) |
| 137149-001 | Type 74LS11 Integrated Circuit | (J9) |
137159-001 Type DAC-08 Digital-to-Analog Converter (C9) 137158-002 Type AM6012ADC Digital-to-Analog Converter (A9, D9) 179010-001 12-Pin PCB Header (J19)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This ‘drawing Isonly conditionally issued, and neither recelpt nor possession thereot confers or transfers any right In, oF li- ‘cense fo use, the subject matter of the drawing or any de- 70-304 sign or tectnical information shown thereon, nor any right > (0 reproduce this drawing or any part thereof. Except Yor (White Tube) anutacture by vendors of Arar Inc, and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.
A005493-01 (Fl. Lt. Harness)
(Connector)
99-11008 (Transformer)
99-110114 (1%-in. Clamp) (Wire nuts not shown for clarity)
Figure 23 Fluorescent Light Assembly (from A036146-01 A) Parts List
Part No, Description
A005493-01 Fluorescent Light Harness 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 79-561816P Spring Connector Wire Nut for 16- to 18-Guage Wires. 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥%-Inch Clamp 035835-01 Y-Lead Connector (part no. A036045-01 is an acceptable substitute)
79-4411001 034544-01 034482-02 (Fuse Post) 036304.01 (Chassis) 46-2017002 (Cover) eanraove ‘Labe) (Fuse) > _—_—_ 79-3206 ( o> (Fuse Block) mA 31> Lt 403588001 or 02 19 a _ 0063201 or-02 i ‘A035891-01 ws) (Fuse Harness) (Transformer)
78-2708 (Hole Bushing) TOP VIEW (F2is not used)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- 78-70501SC afc written permlasion of Atal, Inc. Sunnyvale, a7 is (Capac. Bracket) 29.053 possession theroot confers or tsnsers any ght in or Ir i ‘sense to use, the subject matter of the drawing or any de- (Capacitor) ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture Under the corporation’s written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
BOTTOM VIEW
3A-MDA3501 (Rectifier)
A035890-01 (Int'l) (A034630-01 or A036355-01 (U.S.) A034629-01 79-15021001 (RFI Filter) (Pwr. Harness) (AC Harness) (Term'l Block)
Figure 24 Power Supply Assemblies for X-Y Games A035892-01 (International) A / A036353-01 (U.S.) A
Figure 24 Power Supply Assemblies for X-Y Games Parts List
Part No. Description (Reference Designations and Locations in Bold) A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 Transformer Assembly (international only) (11) Acceptable substitute is A035888-02. A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 Transformer Assembly (U.S. only) (T1) Acceptable substitute is A036354-02. A036355-01 Power Harness Assembly (U.S. only) 29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014002 4-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4, F5, F6) 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Y%-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 03448202 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-10103 CONFIDENTIAL: Reproduction forbidden without the (Inner Pri. $pecitic written permission of Atari, Inc., Sunnyvale, CA. a is drawing is only conditionally’ issued, and neither wiLevers) 75.948S : re (Hex Nut) 99-10095 (Self-Test Sw.) 99-10052 ;ceipt nor possession thereof confers or ‘transfers any Tight in, or license to use, the subject matter of the drawing 99-10096 ‘or any design oF technical information shown thereon, nor (Fastener) any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manulacture under the corporation's written license, no right to reproduce this drawing Is granted or the subject matter thereof unless by written agreement with or written Permission from the corporation. we 99-10071 99-10073 (Slam Sw.) (Decal
75-1408S Gerew) NN |
75-944S 99-10096 (Hex Nut) (Fastener)
99-10063 (Coin Chute) 99-10097 99-10040 99-10101 (Insul.) (Coin niet Chute) | ae et
70-11-47 (Lamp),
99-10080 (Lamp Socket)
7294068,
(Bar Retnr.)
| . 4 99-10041 , (Coin Counter) ee 99-0105 99-10081 (Bar) (Key Holder) 71-A2Kxxx (Coin Mech.) ~~~ 75.9448
(Brkt, 5. 72-9603S 9.10065 (Coin Sw.) COIN RETURN J sain Bon woe 99-0068 99-10075 thru (Lockt. Coil) (Coin Chute) 99-10078 iwi 31-1N4002—Part 99-1042 thru 10008 of 99-10047 99-10045 99. (Diode) it 75-1412S 99-10082 (Coin Sw. Assy) (Retainen) 7S 1428 ‘onveny
Figure 25 American-Made Coin Door 71-40Xxxx D
99-10012 thru 99-10022, and 99-10107 (Button Assy.)
99-10062 (Button) 99-10009 or 99-10010 (Door)
Part of 99-10074
99-10049 (Locking Arm)
75-5520B (Bolt)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc, Sunnyvale, CA. This ‘drawing is only conditionally issued. and neither receipt nor Possession thereof confers or transfers any right in, or Il ‘ene to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted of the subject matter thereof unless by written agreement with or written permission from the corporation.
71-102201 — U.S. 25¢/25¢ Coin Door
71-103203 — U.S. 25¢/25¢/$1 Coin Door 71-102204 — German 2 DM/1 DM Coin Door 71-103205 — German 1/2/5 DM Coin Door 99-10055 thru 99-16059 {Button Cover)
99-10074 99-1070, 99-1083 (cock) thru 99-1092, and 99-10108 (Price Plate)
75.918S (Hex Nut)
75.9158 (Hex Nut)
99-1051 (Frame)
‘71-102206 — German 1 DMS DM Coin Door 71-102207 — Belgian 5 FriS Fr Coin Door 71-102208 — Swiss 1 Fri1 Fr Coin Door 71-102209 — Japanese 100¥/100Y Coin Door 71-102210 — British 10 P/10 P Coin Door 72-JA1405B (Screw) 99-1054 (Btn. Housing) 72-HA1404C (Screw)
99-10061 (Bezel)
99-10066 (Cover)
72-JA1405B Screw)
99-10048 (Harness—not shown for clarity)
71-102211 — Australian 20¢/20¢ Coin Door 71-102212 — Italian 100 L/100 L Coin Door 71-102213 — U.S. 50/50¢ (2 x 25¢) Coin Door 71-103214 — U.S, 50¢/50°/50¢ Coin Door 71-103215 — U.S. 50¢/50%/$1 Coin Door
Figure 25 American-Made Coin Door 71-10Xxxx D
Figure 25 American-Made Coin Door, continued Parts List
Part No. Description 31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 71-1201ADU U.S. $1.00 Coin Mechanism 71-1201FCH Swiss 1 Fr Coin Mechanism
71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism 71-4210PE U.K. 10 P Coin Mechanism 71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Coin Mechanism 71-12100YJ Japanese Y100 Coin Mechanism 72-HA1404C #4 x Y4-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B #4 x 5/16-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Plastite” Black Screw 72-9406S #4-40 x 3/8-Inch Slotted Truss-Head Steel Machine Screw 72-9603S #6-32 x 3/16-Inch Slotted Truss-Head Steel Machine Screw 75-9158 #%-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-918S #8-32 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-9445, #4-40 Polymer Self-Locking Steel Hex Nut 75-948S #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S, #4-40 x Y2-Inch Slotted Pan-Head Steel Machine Screw 75-14128 #4-40 x 34-Inch Slotted Pan-Head Steel Machine Screw 75-5520B #%4-20 x 1%4-Inch Round-Head Square-Neck Steel Bolt with Black Finish 99-10008 Switch Wire Retainer 99-10009 2-Mech Coin Door Only 99-10010 3-Mech Coin Door Only 99-10012 U.S. 25¢ Coin Return Button Assembly 99-10013 U.S. $1.00 Coin Return Button Assembly 99-10014 German 1 DM Goin Return Button Assembly 99-10015 German 2 DM Coin Return Button Assembly 99-10016 German 5 DM Coin Return Button Assembly 99-10017 Belgian 5 Fr Coin Return Button Assembly 99-10018 Swiss 1 Fr Coin Return Button Assembly 99-10019 Japanese Y100 Coin Return Button Assembly 99-10020 U.K. 10 P Coin Return Button Assembly 99-10021 Australian 20¢ Coin Return Button Assembly 99-10022 Italian 100 Lire Coin Return Button Assembly 99-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 99-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (silver wire) 99-10043 Coin Switch Assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins (black wire) 99-10044 Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins (gold wire) 99-10045, Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins (green wire) 99-10047 Lockout Coin Assembly 99-10048 Coin Door Harness Assembly
Figure 25 American-Made Coin Door, continued Parts List
Part No. Description 99-10049 Locking Arm Assembly 99-10057 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Retum Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058 Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063 Right Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066. Coin Return Cover 99-10068 Coin Chute 99-10070 U.S. 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S. 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S. $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 DM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095 Toggle Switch 99-10096 “U"-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Left Half of Coin Inlet Chute 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103 Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw: ing or any design or technicat information shown thereon, nor any ‘right to reproduce this drawing or any pari thereof. Except for manutacture by vendors of Atari, Inc, and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with of written permission from the corporation.
99-15051 (Lamp Holder) 99-1052 . (Spring for Button) 2-7 99-15001 thru 99-15012 (Ret. Button) 99-15038 (Bezel for Button)
99-15040 Z 99-15026 (Lever) os 99-15056 (Coin inlet)
| (Screw for Bezel) | J | » |
99-15025 ——», ~
| (Coin inlet) | © | Se | 9.15039 |
> a \ (Bezel for Cover) PART OF P qeaniee
| 99-15041 | a | a |
Ky 9.15055 . lo a beainesiad ; a (Pivot for Lever) (Retng. Screw) (Lockout Coit) ~
99-15053 (Lockt. Coli Spring) <
9.15027 (Coin Ret. Box)
—— 99-15028 (Coin Ret. Box)
9915037 (Sw. Adjuster) 99-15056 (Screw for Bezel) 99-1 9.15029 5060 (Bracket) << (Sw. Cover) (Switch)
Figure 26 British-Made Coin Door 17100 1-xxx A
99-15087 (Lock Assy.)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specite written permission of Alar, Inc. Sunnyvale, CA, This drawing js only conditionally issued, and neither: Possession thereof confers or transfers any right in, or rr Gense to use, the subject matter of the drawing or any de sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Excent tor manufacture by vendors of Atari, Inc., and for manufacture Under the corporation's written license, no right to repro- ‘duce this drawing Is granted or the subject matter thereof unless by written agreement with or writter permission from the corporation.
9915064’ (Frame)
171001-001 — British 10 P/10 P Coin Door 171001-006 — German 2 DM/5 DM Coin Door 171001-007 — Belgian 5 Fr/5 Fr Coin Door French 1 Frit Fr Coin Door 171001-009 — French 2 Fri1 Fr Coin Door 177001-010 — Swedish 1 Kr/1 Kr Coin Door 171001-002 — British 10 P/S0 P Goin Door 171001-003 — British 20 P/S0 P Coin Door 171001-004 — German 1 DM/1 DM Coin Door 171001-005 — German 2 DMH DM Coin Door (Dual Entry Frame)
47-1002 (Counter)
171001-008 99-15067 (Lock Assy.)
99-15062 (Hinge)
99-15066 (Screw) 99-15085 (Clamp)
171001-011 — Hong Kong $1/$1 Coin Door 171001-012 — Canadian 25¢/25¢ Coin Door 171001-013 — U.S. 25¢/25¢ Coin Door 171001-0%. Spanish 25 Pts/25 Pts Coin Door 171001.015 — Swiss 1 Fri1 Fr Coin Door
Figure 26 British-Made Coin Door 171001-xxx A
Figure 26 British-Made Coin Door, continued 171001-xxx A
Part No. Description 47-1002 Coin Counter 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel} for Coin Return Cover 99-15040 Coin Return Lever 99-5041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15061 Dual Entry Frame 99-15062 Hinge 99-15063 Screw 99-15064 Coin Door Frame 99-15065 Clamp for Frame 99-15066 Screw 99-15067 Lock Assembly
pa
YOUR COMMENTS, PLEASE! Sot printing
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor
Address. O Operator City State Zip OC Other Area Code Phone
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if maited in the United States
eBpe siyy ede, ire Sanna nnn nnn EEE
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
@ RE ETE TREE
t
vi
~@
yada Sates ated. Napad ated, Nala Nand Sate’ Na
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
|f the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © Y s =
s S AS
AL
ATARI
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488