CATHODE RAY TOMES

Castle of Dragon

Castle of Dragon (Romstar Inc.) · Document · 24 pages · 31 sections · original scan

Page 1

: as z2 UNIVERSAL JAMMA C (H I 2 PI r, 2d =a (Ee (LL, SS Le = w =e =)

Page 2

Installing Your

CASTLE OF DRAGON

New Game Package

Table of Contents

New Game Package Contents ........ cece eee e eee nent e cette eee ene neees 2

Power and Monitor Requirements 0.0.0.6... c cect eee eee eet eee e tenet tenn eee 2

Recommended Tools and SUPPIi€S . 16... cece eect nent eens 4

Installation PrOC@CUIeS ... 6... cee cece ee tence eee een nee een eet eee enes 5

Coin Meter Diagram... ... 6.6 cece cee eee eee rete een ene ee 10

Monitor SYNC TIPS 6... 6c cee ec eee ne een ee eee eee een ents 11

Control Panel PositiONINg..... 2... cece cece cee n ee ene eee eee enone 12

Factory S€ttingS 0.0... cece cece cen eee ee cee eee sees este ete eeeteneeetaenes 15 Dip SW Diagram oon etn eee ene eee eE 15 In Case Of Difficulty ...

Main Harness Connections

Page 3

CASTLE OF DRAGON NEW GAME PACKAGE CONTENTS

DESCRIPTION PART # || DESCRIPTION:

1 Main Printed Circuit Board (PCB)62014 YELLOW Player Button
| Monitor Bezel6208| Marquee
1 PCB Feet Assembly05241 Conwel Panel Overlay
1Connecting Wire Harness (Jamma)02151 Plex Control! Cover
2 Eight-Way Joystick02101 Set Side Graphics

8 Player Button Assemblies 1 Set Play Instructions & Function Labels

2 Red Player Button02291 Installation Manual

2 Blue Player Button 0233

Note: Replacement accessories available through your exclusive Romstar distributor

POWER REQUIREMENTS MONITOR REQUIREMENTS

7 amp minimum Horizontal Mount Raster Scan Tamp minimum Negative Composite Sync 1 amp minimum Required for Jamma Compatibility

Page 4

ROMSTAR ‘inc.

Invites You To Use

OUR PHONE OR FAX NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER ROMSTAR GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS.

ROMSTAR, INC. 22857 LOCKNESS AVENUE ® TORRANCE, CALIFORNIA 90501 TECHNICAL QUESTIONS — SENIOR TECHNICIAN DARRYL WILLIAMS EXT, 119 RMA'S / PARTS QUESTIONS — PARTS MANAGER AUDREY SMITH EXT. 112

PHONE (213) 539-2744

FAX (213) 539-3626

WARNING

Federal !aw provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

Page 5

Before You Get Started. . .Stop!

Does your new game package include all listed parts? (Is it complete?)

  • _Isthe game you have chosen to transform able to supply all the required voltages for the new game?
Note: Some games, (i.e. Ms. Pac Man, Galaxian, etc.) regulate their voltages on the main PC.B. This makes the existing power supply inefficient. These games will require a change in power supply for your new game. Many game supply houses can offer you a switching regulated power supply for a relatively low cost.
  • !s the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical Mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
  • Do you have the necessary tools? (See the recommended tool list)

Caution

F.C.C. Reguiation Compilance Operation of this equipment in a residential area is likely to cause interference

  • in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4" © 7/16” Drill Bits 1/4” Plex Bit 1-3/16" Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Smail File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own Painting) Paint Brush and Paint (don’t forget the primer} Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Nights Sleep Staple Gun and Staples Soldering iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” ¢ 3/16” Masking Tape 3 112” OR 4” Wire Ties Spray Window Cleaner and Rags (baby diag ers work GREAT!)

Thorough Research shows that two and a half minute games both satisty players and also keep the quarters flowing. {f games aren't running about two and a half minutes tong, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 6

Installation Procedures

Something To Think About Your final product will be a new game. You have made a wise decision to transform a game that has seen better days in the all important cash box into anew game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is... amew game at a very low cost. Fact: Spend alittle time on the cabinet’s appearance (i.e. marquee, contro! panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game Package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary g/itches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game Remove the following:

1,Main logic board(s)4.Monitor Bezel
2.Control panel5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. You may consider having an auto body shop take care of your painting needs.

If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 7

Time To Install Your New Goodies

Before You Start. . .Remember DO NOT Do This Work With The Power Oni

Logic P.C.B. Mount the logic board securely (away from power supply). A Mark and drill pilot holes (3.32”). B Install the P.C.B. into cabinet. Use feet and spacers supplied and adjust them so that the screws will go through the holes in the cabinet.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panei, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and uSe their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Soider the new wire designated for that position to the original wire you just stripped.

Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING

INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do It right.

  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble. .
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Page 8

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. . .CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. Youcan check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires

Connect the designated wires to the coin switches and meter. (See tech tips)

  • Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new PCB. is functional.
Page 9

Time to Apply Power:

  • Look and smell for smoke. (TURN OFF iMMEDIATELY IF ANY IS NOTICED)
  • Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker.
  • How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative (see tech tips section).

NOTES:

B) Now how's your picture? © It it centered? ® Is it too bright or dim? © Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Refer to your monitor manual - switch two horizontal yoke wires and then switch two vertical wires. (Pull the pins in the connector on the monitor P.C.B. to switch them.) or check Dip Switch Tables

Page 10

Control Panel Assembly

  • Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overlay until the new holes have been drilled.
  • Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that yournew game investment is well worth protecting. . .and the control panel is the first place to show wear and tear. © You will need to cut this piece to size. Use the control panel as a template. © Use arazor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
  • Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes.
  • Drillthe same holes on your plexiglass panel protector. Once again use your pane! as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
  • The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
  • Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easler: Pee! the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel.
  • Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible) On

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics andscore the new marquee deeply to fit the cabinet. Break off the excess with pliers.

Note: when cutting marquee to size, check to make sure that you are cutting as little of the necessary art as possible (name, manufacturer, etc.)

Be sure the light behind the marquee works. Everything should always work on a new game. Take your time ... Don’t forget this is going to be a new game.

Page 11

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet}. Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can't get a coin into it. Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?} B. Play your new game . © Are all the player controls working?

  • Are-the game sounds present? © Is the volume level proper? © Are the dip switches set properly? Well, that’s about it. Good Luck.

Coin Meter Diagram

To attach a coin meter, use following diagram:

+5VDC +12VDC or +24VDC

DIODE (IN4004)

COIN SWITCH TO MAIN HARNESS COIN | ° OR COIN DIODE (IN4004} COUNTER SWITCH GROUND — OUTPUT

Page 12

Star Tech Tips We are grateful to Star Tech Journaltm for allowing us to publish the following excerpts from their journal.

  • Monitor Sync Ifyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going. CURE 1: Install asimple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.) HORIZONTAL SYNC INPUT FROM P.C.B. 5. Vcc SVDC (PIN 14} (OR COMPOSITE SYNC INPUT) SOLDER TO. HORIZONTAL SYNC OUTPUT TO MONITOR # EXISTING CHIP {OR COMPOSITE SYNC OUTPUT) a VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR

FIG.2

BENT PINS aa =) GND [PIN 7} Leama}

FIG.1 SOLDER

CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x140B.

Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS6 transistor as follows: Collector to anode leads of diodes X20! & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded} lead of zener diode ZD201. Insert a IN4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3) REDI GREEN 2 BLUE 3 GND4 FIG. 3 VERT. S HORIZ. 6 MPSAS6

IN4148, 0000

CUT TRACES =?

x201 an)

Page 13
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor Negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2: Connect IN4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. {See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.

IN4148

NEG: SYNC INPUT

n--|-=

1Q-H vv O! Gno

eeSLa
FIG. 432!

GND BLUE GREEN RED t x —t On OVO _ O_O Oo;

65432i

IN4148

CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from W102 to either J2 or J3.

CURE 3: For Wells-Gardner K4600 series monitors Replace C 356 (4 7uf 25V) on the Horizontal vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.

Control Panel Positioning

PLAYER 1 PLAYER 2

2 “>o-== 8 WAY JOYSTICK ---7~

Page 14

ILLUSTRATED

PARTS LISTS

NOT USED ON MOST MODELS

MONITOR CONNECTIONS

  • VIDEO LAYOUT

COIN METER

COIN METER LAYOUT 98-4115-00 MICROSWITCH WITH GOLD CONTACTS

Exploded View

J59-2213-00

Page 15

56 PIN EDGE CONN. PIN-OUT CHART (JAMMA COMPATIBLE)

WIRE COLORSOLDER SIDEPARTS SIDEWIRE COLOR
BLACKGNDA1GNDBLACK
BLACKGNDB2GNDBLACK
RED+5VCc3+5VRED
RED+5VD4+5VRED
WHITE-5VE5-5VWHITE

YELLOW +12V F 6 +12V a YELLOW

KEYHKEY
COIN COUNTER 2 | J8COIN COUNTER 1BROWN
COIN LOCK OUT 2|K9 | COIN LOCK OUT1RED
WHITE/BLACKSP (-)L10SP(+)WHITE
OP.-BLU/BLACKN.C.MINC.BLUE-OPTION
GREENVIDEO GREENN12VIDEO REDRED
GRAYVIDEO SYNCP13 |VIDEO BLUEBLUE
-RED/BLACKSERVICE SWITCHRVIDEO GNDBLACK
OP.-BRN/BLACKTILT SW.STEST SW.BROWN
COIN SW. 2TCOIN SW. 1WHITE
WHITE/GRAYSTART SW. 2USTART SW. 1
WHITE/VIOLET2P UPVvIP UP
WHITE /BLUE2P DOWNWw1P DOWN
WHITE/GREEN2P LEFTXxIP LEFT
WHITE/YELLOW2P RIGHTYIP RIGHT
WHITE/ORANGE2P PUSH I *ZIP PUSH 1 »
WHITE/RED2P PUSH 2 «aIP PUSH 2 «
WHITE/BROWN2P PUSH 3 «bIP PUSH 3 «BROWN
GREEN/WHITEN.C.CcNc.BLUE/WHITE
YELLOW/WHITEN.C.dRED/WHITE
BLACKGNDeBLACK
OPTION-BLACKGNDfBLACK-OPTION
  • PUSH | = ATTACK PUSH 2 = JUMP PUSH 3 = SHIELD
Page 16

OPTION SWITCH SETTINGS

The following option switch settings were designed to allow the customizing of various game features to suit different environments. If used wisely, the flexibility they offer can maximize game performance and increase potential earnings.

DIP SW (1)

itemCondition| 1]2 | 34] sle]7|s

°& | OFF Don’t Touch ON

ScreenNormal*OFF
Tuming OverReverseON

1 out of 4 Scenes

Demo Sound boi Test Mode OFF

1 out of 8 Scenes: ON

Game

Test ON 1 COIN 1 PLAY OFF OFF 1 COIN 2 PLAY ON COIN 1 2 COIN 1 PLAY OFF ON 2 COIN 3 PLAY ON

1 COIN 1 PLAY % OFF -—————_ OFF 1 COIN 2 PLAY ON COIN 2 2 COIN 1 PLAY OFF ON 2 COIN 3 PLAY ON

DIP SW (2)

Item

Difficult

200,000/400,000 Pt. OFF OFF Exua Player 150,000/300000 Pt. ON

Score 300,000/500,000 Pt. OFF | t—— ON 400,000 Pt. ONLY ON

3*OFF

OFF

Number of5ON
Player's Life2[OFFI on

1 ON

* Don’t Touch

* Don’t Touch M §|_[x|-|-[a]« & [a]

Zz fe} ol + BMPS BRB] os

Fa a ZiE/E;EIE 2/2/6/6/6/6| 5 Slolsislaleic 5 cle; Ese}e

  • |6|/6]/S/6]5

g re} 4 a Zlelz]> a|3|% x 2 o{¥lglele| | 5 PlElslalziz|"le uId Zz x 8/9 }2)/2 tl ls|s|e/e} |s “ ol-|-|- 3 =

a 1)

Qa 5 |z/8

w83 lallaFd

> [E/S/slzlz/z2/2 6 (2 S/£/8/8/2|&

5esaleing

ik *

Parts Side

op sw || 28 or sw 2[|

vri ©

  • Rec. Setting
Page 17

CHECKPOINTS IN CASE OF DIFFICULTY PROBLEM / CAUSE-CURE No Raster/No Video ~ Check A.C. line cord

  • Check line fuse ~ Check monitor brightness ~ Check power switch and/or interlock switch ~ Check all solder connections on line filter and transformer
  • Check for proper orientation of the PCB, connector

Raster/No Video ~ Check all PCB to monitor connections

  • Check power supply voltage on PCB

No Video/Game sounds can be heard

  • Check monitor brightness ~ Check all PCB to monitor connections

Wrong colors ~ Monitor needs degaussing, ~ Check for proper wiring between PCB and monitor

  • Check monitor adjustment and adjust if necessary

Wavy picture —Check monitor ground is properly connected to monitor

  • Be certain sync inputs are properly connected to monitor
  • Check horizontal hold adjustment

Horizontal/Vertical Roll

  • Check horizontal and/or vertical hold adjustments
  • Check for proper wiring of sync from PCB to monitor

No sound ~ Check for -5 volts on edge connector of PCB ~ Check volume control potentiometer adjustment

  • Check for +12 volts on edge connector of PCB ~ Check wiring from PCB to speaker ~ Check speaker for low resistance between the “+” and “-" tabs

Bad sound

  • Check wiring to speaker for bad solder connections
  • Check sound with another speaker

No switch input ~ Check ground connection to switch/es

  • Check wiring between PCB and switch/es for proper connection
  • Check switch/es with an ohmmeter to verify proper operation

Switch operates incorrect function

  • Check wiring between PCB and switches for proper orientation
  • Check wiring for shorts between switch inputs

No coin meter = Check wiring to coin meter

  • Check that +5 volts is on +” side of meter
  • Verify a +5 volt meter is used

When coin switch is made and meter pulses, the screen blanks out and/or game resets ~ Verify that a meter with a diode is used ~ If no diode is built in meter a \N4004 can be used across the meter. Cathode to "+" side of meter and anode to “-” side of meter

Page 18

ROMSTAR JAMMA HARNESS PLEASE REFER TO MAIN HARNESS

VERSIONS 1-4 PIN-OUT FOR PINS Z, a, b, 22, 23, & 24.

JAMMA GE.BK JAMMA CA.BLU

Wire ] Wire

Color Solder Side Parts Side Color

1 Black Ground Ground Black

2 Ground Black Black Ground Ground Black

3 +5VDC Red Red +5VDC +5VDC Red

4 +5VDC Red Red +5VDC +5VDC Red 5 White White

Ground Black Ground Red +5VDC Red +5VDC Yellow +12VDC Post Red Coin Counter 2 Coin Lockout Black ‘Speaker (-] N/A Green Video Green White Video SYNC iorenes: Pink Service Switch Yellow Tilt Switch ‘Orange Coin 2 Gray 2P Start Green 2P Up Blue 2P Down Violet 2P Left Yellow 2P Right

Red ‘Orange +12VD0C Yellow Yellow +12VDC +12VDC Yellow

Post Post Post Coin Counter 1 Violet Brown Coin Counter 2 Coin Counter | Brown Coin Lockout Red Coin Lockout Coin Lockout Red 10 ‘Speaker {+} Gray Black Speaker (-} ‘Speaker (+) White " N/A Blue N/A N/A Blue Video Red Red Green Video Green Video Red Red Video Blue Biue Gray Video Sync ic Video Blue Blue Video Ground Black Red N/A Video Ground Biack Test Switch Blue Brown N/A N/A Brown 16 Coin) Tan White SRVC Switch Coin White 7 IP Start Brown, Gray 2P Start IP Start Gray 1P Up Green Viioet 2P Up 1P Up Violet 9 1P Down Blue Biue 2P Down IP Down Blue 20 IP Left Violet Green 2P Left IP Left Green 2i IP Right Yellow. Yellow 2P Right IP Right Yellow 22 Red Orange Orange as Orange Red Red Brown Brown Blue N/A N/A Blue Blue N/A N/A Biue Black Ground 27 Ground Black Black Ground Ground Black Black Ground 28 Ground Biack Black Ground Ground Black

Wire color / Stripe color Wire color /Stripe color [NI mle fnjoln fala

N/A N/A 25 N/A 26 N/A

<falUlOfwiulrrfx (aS ]zZ ja je jo fe [9] > /B)x |>|NJwlolulole le cJalUjalwiufr[alx</afsjzlo fein |r jo]> /B]x|>|N{ajoalujole]—

NOTE: Please refer to manual harness pinout for pins

= N

Page 19

= o

JAMMA DA.BK

JAMMA SK.GR

Black

Ground

Biack

Red +5VDC Red Red +5VDC +5VDC Red

Red +SVDC Red Red +5VDC +5VDC Red

White ~5Vv0C White Green ~5VvOC ~5VDC Green

Yellow +12VDC Yellow Yellow +12VDC +1ZVDC Yellow

Post Post Post Post

Brown/White Coin Counter 2 Coin Counter 1 Bm/wht Coin Counter 2 Coin Counter I Brown

Red/Black Coin Lockout T

INI me linfolN lala Cain Lockout Red/Blk Coin Lockout min [mle |infolsN|olo Coin Lockout

White/Black Speaker (-} rr Speaker {+} White White Speaker {-) speaker [+] White

Audio

Green Video Green 12 Video Red Red Light Green Video Green Video Red Pink

Gray Video Sy come inea: 13 Video Blue Biue Gray/White Vide0 SYNC com nnsi Video Blue Sky Blue

Red/Bik Service Switch 14 Video Ground

Violet Service Switch Video Ground

Tilt Swatch 15 Test Switch Brown Gray NWA N/A Orange

Wht Bik Coin 2 16 Coin t White Coin 2 Con Violet/White

wnt/ay 2P Start 7 IP Start Gray [ WhI/BIk 2P Start IP Start Black/White

wht/Vio 2P Up 18 1P Up Violet Brown/ Black 2P Up 1P Up Brown/White

Whi/Biu 2P Down 19 1P Down, Bie Red/Blk 2? Down IP Down Red/White

WhyGm 2P Left €falulalwiulr}[ajx|o/S]Z Jo le lu |b Ja |> |B} x 20 IP Left Violet (Orange/Black 2P Left IP Left Orange/White

Wht/Yel 2P Right IP Right Yellow Yellow/Black 2P Right 1P Right Yellow/White

Wht/Ora Orange Green/Black Green/White

Wht/Red Red Blue/Black Blue/White

Why/Bm Brown <lmfufofwlu jr} fx |s/s]2 fo le jo je [D> |B |x |>|N] olo

Gm/wht N/A N/A

Yel/wht N/A N/A

[Black

Wire color / Stripe color

NOTE: Please refer to manual harness pinout for pins

lel.

Wire color/Stripe color

Page 20

FHEFEE EHH HFEF HH HEHEHE HEHE HEFHEFHEFHFH EOF EH HHH OH H+

LIMITED WARRANTY

ROMSTARING. (‘Seller’), warrants only to the initial purchaser of its products thatthe items listed below are free trom defects in material and workmanship under normal use and service for the warranty periods specified:

A. Printed Circuit Boards (60) days B, Electronic Components (30) days C. Television Monitors (30) days

No other parts of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from Seller to its authroized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specitied, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective.

B. Such products are properly packaged and then returned, prepaid to Seller’s plant.

This warranty does not apply to any parts damaged during shipping or handling, or due to improper installation or usage, or alteration. Inno event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of Romstar Inc. product.

(WARRANTY DISCLAIMER)

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PEPHEHE EHH HEHEHE HEHEHE EHH ED HEFEFHIFHEEEEH EF HFEF HEF HH FSH HEH HHH Het FHFEEH HEEL EFEFH HEHEHE HEHEHE EEEFEFEFEFEHEEE HEHEHE HH FHF HEH HH HH Hoos

PEDFHH EH EH HEHEHE HFEF EH HHH HH HE HHH Hs hho oes 19

Page 21

* * RETURN MERCHANDISE AUTHORIZATION — [RMA]

ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.

ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #).

ALL PC BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL NOT BE ACCEPTED.

ROMSTAR WALL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.

ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WILL BE ISSUED.

ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY ROMSTAR WITHIN 24 HOURS QF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).

FOR ANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.

ROMSSTAR WILL REPAIR OR REPLACE ROMSTAR PCB's FOR A MINIMAL CHARGE FOR A PERIOD OF 1 YEAR.

MINIMUM $50.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR RETURNS.

ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS WARRANTY. (ATTEMPTED REPAIR USUALLY INCREASES THE TIME AND COST OF REPAIR.) :

(*ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR)

**NOTE: IF AN ADVANCE REPLACEMENT IS NOT RETURNED TO ROMSTAR, INC. WITHIN 30 DAYS (ONE MONTH) AFTER THE DAY OF ADVANCEMENT, THE CUSTOMER WILL BE LIABLE FOR FULL PAYMENT OF THE PART OR: PRINTED CIRCUIT BOARD.

Page 22

NOTES

Page 23

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 24

ROMSTAR inc.

ROMSTAR, INC. 22857 LOCKNESS AVENUE * TORRANCE, CALIFORNIA 90504