Saturn Sega Saturn (PAL) Service Manual No. 013-1 June 1995
Saturn (Sega, 1994) · Service Manual · 68 pages · 14 sections · original scan
SEGA SERVICE MANUAL
SEGA SATURN (PAL)
NO. 013-1
ISSUED JUNE, 1995
CONTENTS
SESS 3576) 13 (67-4 8 (0). (ce 3
- IDENTIFYING PARTS «srt r etter tee tet terete eter eens 4
- ACCESSORIES +++ sete ee teen tee ee ce te eee ee eee ene e eee 5
- IDENTIFICATIONS AND LOCATIONS OF CIRCUIT BOARDS ---- 5
- DISASSEMBLY PROCEDURE «+--+ sess r errr rere reer 6
- CD DRIVE MAINTENANCE AND ADJUSTMENT: +++ ++ 00-0000 ++ 8
- BLOCK DIAGRAM
- SCHEMATIC DIAGRAMS +++ +--+ errr rere etree tet t etree tees 13
- CIRCUIT BOARD DIAGRAMS «++ +++ sere errr terete trees 27
- PARTS SPECIFICATIONS
- EXPLODED VIEW & PARTS LIST + +++ +++ essere terete erste eres 70
11-1. Exploded View: +++ 1sr rect r etre et rtt tert eee tence eee e eee 11-2. Mechanical Parts List -
11-3. Electrical Parts List -+++ +++ ++ sr ert ttt ttre eee eee eens
11-4. Accessories/Package list +--+ +++ srs srr ttt tree r treet etree es 77
Sega Enterprises, Ltd.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
This console is classified as a CLASS 1 LASER product.
SAFETY PRECAUTIONS Notice: Comply with all cautions and safety related notes located on or inside the cabinet and on the chassis. . When replacing a chassis in the console, all the protective devices must be put back in place, such as barriers, non-metallic knobs, adjustment and compartment covers/shields, isolation resistors/capacitors, etc. When service is required, observe the original lead-dress. Extra precautions should be taken to assure correct lead dress in the high voltage circuit. Always use the manufacturer’s replacement components. Especially critical components as indicated on the circuit diagram should not be replaced by other manufacturer’s. Furthermore, where a short-circuit has occurred, replace those components that indicate evidence of overheating. te
we
PRODUCT SAFETY NOTICE Many electrical and mechanical parts have special safety-related characteristics. These are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a A\ in the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the SEGA recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time.
This symbol indicates a Fast Operating Type Fuse.
Hh This symbol indicates a Time Lag Type Fuse.
SATURN COMPATABILITY
Audio CD:
The normal audio Compact Disc is playable on the Saturn machine, and can be altered with all the effects of a modern Hi-fi and more. Surround sound, vocal cut-out for Karaoke, program sequence of tracks and shuffle to name but a few. You need no extra equipment to play music CDs on your Saturn.
CD+G:
CD and Graphics are a format where simple visuals can appear on the screen that relate to the music. These visuals might include stills of the band, or other pictures. You need to buy no extra equipment to use CD+G on your Saturn.
CD+EG:
CD and extended graphics is a new medium ready to be utilised by the music community. It is basically an enhanced version of what is described above in CD+G. You need no extra equipment to use CD+EG on your Saturn.
MPEG:
MPEG is the standard industry format for compressing Full Motion Video footage. This means that the footage takes up less disk space, and when it is to be viewed, the MPEG program decodes the footage and plays it on screen. The MPEG add-on is needed in order to use the MPEG video CDs and Philips CDi. At the current rate of compression one movie can fit on two CDs.
CDi:
Developed by Philips, CDi is an interactive CD format that can be used in a variety of educational and entertainment purposes. Using video footage and CD quality sound CDi has become an industry leader in the field of interactive fun... The MPEG add-on is required to access the full range of CDi software
Kodak Photo CD:
Photos stored on CD have theoretically infinite life, are always picture perfect and will never fade or be otherwise damaged. The Saturn can access Kodak Photo CDs with the use of another Saturn CD which allows the user to see display the photos in various ways. There are many Kodak Photo CD stores open in the major cities.
Frame Buffering: A technique to maximise graphic display performance by letting the graphics processor chip “set aside” images it has already calculated, allowing it to work on enerating the next fraction of a seconds visual images, all while the screen is still busy painting the last fraction of a second’s display.
Playfields: The background(s), anything that is on screen that it not a sprite. When two playfields (layers of bacground) are contolled properly, parrallax scrolling can result.The Sega Saturn has a whole chip dedicated to controllingbackgrounds (the VDP2 or Video Display Processor 2”) that can generate 5 distict layers of background at the same time.
Polygons/Second: (1000’s of) The number of polygons of a given size that can be drawn on the screen in one second. This figure does not include the size of the polygons, nor their texturing, shading, or lighting.
Realtime: An important adjective that usually indicates the game display is being re-calculated every second, taking into account the full effects of the player’s actions. When reffering to a game’s response or speed, it means the game responds instantly to the player’s commands.
Render: Drawing 3D graphical objects on a computer or game machine. “BUG?” and “Clockwork Knight” are filled with beautifully rendered characters.
Texture Mapping: Copying a bit-map onto the faces of selected polygons to give the illusion of surface texture. “Daytona USA” is a great example of a texture mapped game.
Wireframe: A connect the dots approach to showing graphical objects by drawing lines between sets of points that make up a geometric outline.
Dynamic Perspective: Constantly changing the point of view (“camera angle”) so that the players feel that they are weaving in and around the on-screen action. Typically requires strong scaling and rotational capabilities. This can be seen on Sega Sports games on Saturn.
- SPECIFICATIONS
Ratings
Model MK — 80200-50
Power supply AC220-240 V 50/60 Hz
Power consumption Approx. 20 W Temperature 5°C to 35°C Operating environment Humidity10% to 80% RH (no condensation) 260 mm(W) X 230 mm(L) X 83 mm(H) Dimensions (10.2 inches) x (9.0 inches) x (3.2 inches)
Specifications
Master 32bit RISC SH2 (28.4 MHz, 25MIPS) CPU Slave 32bit RISC SH2 (28.4 MHz, 25MIPS) Sound 68ECO000 (11.3 MHz) Work RAM 16 Mbit
Video RAM 12 Mbit
Memories Sound RAM 4 Mbit
CD Buffer RAM 4 Mbit
IPL ROM 4 Mbit
Backup RAM 256 Kbit Resolution 320 X 224 dot etc. Graphics Colors 1024/2048 (16,770,000 simultaneous transmission) Sprite Enlargement, Reducation, Rotation, Transformation 5 screen maximum
XY Scroll 4 Rotation 2 Scroll Enlargement / reduction 2 Window 2 Vertical cell scroll
Special features Lateral line scroll Enlargement / reduction Polygons Specialized hardware
CG Functions . Wire frame
Special features Flat shading Gouraud shading 32 channels ; Sound PCM & FM sound source Sempling ate 4 1 kHz max. Audio DSP CD-ROM Intelligent double-speed CD drive
{Note] Characteristics and specifications may be changed without notice.
- IDENTIFYING PARTS
2-1. Front View of Console
OPEN Button
POWER Button
POWER Light 2-3. Control pad
To Control Port
RIGHT SHIFT Button
X Button Y Button Z Button
A Button B Button DIRECTIONAL Button START Button C Button
CONTROL PORT1 CONTROL PORT 2
2-2. Back View of Console
TT Taxa POWER Jack SS | — TT Gn epee ooetn saoee
Battery Cover Lithium Battery Master Reset Switch Communications Jack AN OUT Jack
- ACCESSORIES
Positive Side
Lithium Battery (CR2032)
AC Cable [UK] AC Cable [SOE] AC Cable [AUSTRALIA]
- IDENTIFICATIONS AND LOCATIONS OF CIRCUIT BOARDS
> CD Drive Unit Power Board
P. SW Board
R. SW Board
- DISASSEMBLY PROCEDURE 5-1. Top Case Removal 5-3. CD Drive Unit Removal
- Remove six screws ® and then the top case in the 1) Disconnect two connectors and one flat cable. direction of the arrow. 2) Remove the CD drive unit in the direction of arrow
CD Drive Unit
Fig. 5-1 Fig. 5-3
5-2. CD Compartment Lid Removal 5-4, SH-1 Board Removal
- Remove two screws (8) and then the bracket lid CD 1) Remove four screws @ and then the top shield spring. plate.
- Remove spring © . 2) Remove screw (D and release three tabs, then lift
- Remove two screws (D) and then the oi! dumper. the SH-1 board in the direction of arrow @ to
- Push the lever in the direction of arrow © to remove it. release the boss and then push the lever in the direction of arrow ® to remove the CD compart- (s)) ment lid. @ Top Shield oy \
Fig. 5-2 Fig. 5-4
5-5. Main Board Removal
- Remove four screws ® holding the CD drive unit supports.
- Remove five screws © and then the main board.
5-6. Power, Power Indicator and R. SW Boards Removal
- Remove three screws @ and then the power board.
- Remove screw @) and then the power indicator board.
- Remove two screws ©) and then the R. SW board.
Power Board
Fig. 5-6
6-1. Maintenance of Pickup
- Checking the laser diode As the laser diode wears out, the RF level (amplitude of eye pattern) becomes lower. Check that the RF level is 0.8V — 1.4Vp-p during maintenance. If the RF level is less that 0.8Vp-p then the pickup should be replaced.
- Variable resistor on the APC board The variable resistor attached to the pickup on the APC board is used to adjust the output power of the laser. This adjustment is done at the factory and can not be performed in the field. If the laser’s output power is low, the laser diode has worn out and should be replaced. Adjusting this variable Tesistor may cause damage to the laser diode.
- CD DRIVE MAINTENANCE AND ADJUSTMENT
6-2. Laser Pickup Replacement Procedure
Turn the power switch off and unplug the power cord from the AC outlet.
Replace the pickup.
Set the door close detection switch to on manually and turn the power switch on. Check that the laser emits light for approx. 3 seconds and the pickup lens moves up and down.
[Note] Be careful not to bring your eyes too near to the laser and do not look straight at it as this is dangerous.
Check the FE bias.
Adjust the focus gain.
Adjust the TE balance.
Adjust the tracking gain.
Check that the eye pattern waveform can be observed at the RF test point. (0.8~1.4Vp-p)
Replacement complete
{Note] Since the adjutments influence each other, it may be necessary to repeat them 2 to 3 times. times.
Adjustment Preparation Apply markings to the positions of the variable resistors before adjustment. If the adjustment are out of the specifications, the following symptoms may occur. [Focus gain] If the focus adjustment is too low the pickup lens will not be able to focus properly and the disk will not rotate. If the adjustment is too high portions of a track may be skipped and noise will increase. [Tracking gain] If the tracking adjustment is too low the drive is more susceptable to shocks or bumps, portions of a track may be skipped or the disk time counter may stop. If the adjustment is too high the pickup lens may oscillate leading to unstable or distorted sound. The focus and tracking adjustments are done so as to mutually satisfy conflicting characteristics.
6-3. Test equipment and tools necessary for adjustment
- Oscilloscope
- DC voltmeter
- Non-metallic adjustment screwdriver
- Test CD (A-BEC TCD-792A)
6-4, CD Drive Unit Adjustment Procedure
FEIN 10k Q Oscilloscope
Po
Oscilloscope
BPI vc 1/2 6-4-1. FE (Focus Error) bias adjustment and focus gain adjustment
- Connect the oscilloscope to test point FE IN as shown in Fig. 6-2.
- Turn the power switch on and set the CD drive to the stop mode.
- Adjust R114 (FE bios) so the DC voltage at test point (FE IN) is OV. the
- Play the first track of the test CD and adjust RI11 (Focus gain) so the DC voltage is — 7mV.
6-4-2. FE balance and tracking gain adjustments
- Connect the oscilloscope to test point BP IN as shown in Fig. 6-3.
- Turn the power switch on and play the first track of the test CD.
- After play has begun, connect the TEST pin to GND.
- Adjust R104 (FE balance) so the center voltage of the waveform is OV.
- Adjust R113 (tracking gain) so the amplitude of the waveform is 0.4V as in Fig. 6-4.
TA AAA LY
Fig. 6-4 LUV Wo 0.4V
—~10—
- BLOCK DIAGRAM
;RTRIDGE_ CONNECTOR en <n i CNI cng | CONNECTOR | | MPEG \ H feros} | | VIDEO } | ens (Ex8G0-EXB624) vonle-t tt im icso1 |} = power [fy +9¥ (CD DRIVE. FOR PLL) USED FOR THE POWER SUPPLY ! it i H SUPPLY #5V (WCC. AVCC2) USED FOR ALL CHIPS OTHER THAN SDRAM SHI { it 1 BOARD iF +3. 3V(LVCC) USED FOR SDRAM BOARD 1 it BUFFER | ot pupit CONNECTOR \ ocu |. tt 1c302 [1 CLOCK ' 1301 roe '
- 318HHz 1 ii NPEG sc i vt aupto | f SCPUCLK ' rt reaor | | 2 PLL scspclk “UP_TO 5 BACKGROUND SCREENS 1 oon ee ! 1620 rele (SCROLL SCREENS) i ce rete “DISPLAY PRIORITY ! it bssap: meLKa +CAN MOVE SCREEN UP. DOWN. RIGHT. ! 11] progam} atti t LEFT. ROTATE MAGNIFY AND REQUCE ! it ROM Hl Chocks / “COLOR OFFSET \ i 1c303 || (OT USED) + SHADOW I BUFFER ti up To 72 MINUTES = AuoIo 1 RAM ' | MPEG 1 (30 FRAMES PER SECOND) NISC BAO \ 1c102 rt ' POSSIBLE ON ONE CO. rf " FOR shia ' THOT 1 (OPTIONAL) | + INTERNAL WORK RAM ! ! = : i 1 1X2 SPEED 28, 6MHZ | 1 SH1 €102) ' YN 1 cO-RoM 3 arse PU se 7 ABD ADIS. AAD-AKeS \ ' BOARD | Oo}! +4kby te CACHE meee) (A-CONTROL oN Lorn. ----b----- ! | ! “INTERNAL MATH co \ ‘CD INTERNAL /EXTERNAL iz _ suse sHe WORK BUS
- (SLAVE) RAM (eeeheee: + DSP (SOUND | f s9pcH tee od ; CHANNELS *32bit RISC CPU cpus csoram J 4MPIE SeLyeLs. SPRITES. vope + FI BCHANNELS {Borne cba=co31,) ———————} COLOR CALCULATION rio Po ier TINEA Bae ( G30-cx24 ) WORK | — Ambit EXTURE *32bit INTERNAL. Lébit EXTERNAL CONTROL. “| RAM + SHADING . souno |- 4tbit “INTERNAL MATH PROCESSOR HIGH 2Mbit RAM 4 ace 14 : Ra 1C6 (SORAM) SPRITE Frame | — Mbit VIQEO CHARACTER ReM Ran son icl2 aapReSs an cPu slébit CISC CPU BUS 1¢26-1030 EC-BUS (68EC0004 «11. 3MHZ ORI VER ( Epo0-Eco1s.) 4Mbit 1c18 NATAL Frame | — 2tbit VIDEO = pane | — (PL RAM RAM ROB BNCODER To WV ATA ROH - 113 ICl6 5S H 1c7 | — mbit +VOPI READS ONLY ORAW COMMANDS = L———~ ONbit FROM HERE AND i THE DRAWS TO THE 5 aycnur — osekbit FRAME RAM 1c8 CLOCKS _CLOCK4 “Maz 32. 768KHZ cn 0 ScE2 %3 x4 To | — (BESEL., ) bs] CONTROL sHpc CONTROL, | paps L_ | ico BATTERY { INPUT: MRES FROM SW3. SRES FROM SW1 (CR2052) SYSTEM RESET CONTROL < OUTPUT: CORES. COPRORES. SNDRES. \ SYSRES. MSHRES. SSHRES
A B | c | D | E E | & | H -— W4- Nn
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
8-5. Schematic Diagram-5 [Main C.B - 5/6] wor sen vee veo vee vec exes O Oasis see 5 vee = Goal “Tio 5 Ras 0 cNeXB ver Xs Ret Ic9 ma Tye 1¢35 feR sik BiS-S74e se ie Te o1 pms Ta by 9 a 1 sr tor? ssi 4h ite [a test PG, ik sf Rut CES tea va R68 Lud a= ts naa T 5 iy Sik ‘te oo 20 330k tia) prea cones bed RIGHT eee x4 es. + ees fe 3 [oo [our cSt S32 Pome St cRTGO a ‘ 06 pom TH Veer fe 3% sites | @) 2 in 05 Al Hi cna ccvaus 36 sires La 5, ® 06 Ter Hs tL eee [2 5 Qk TT ee syecce 7 RIGHT t- Fors. ie vee wee oe P= SSeS EFT 1 01% Le sa fe} fo) @ | m Ineo a» f= svat oy Eid | Fons fete (D) sms >S Basins Ti ‘ov no [2 Dorset [ ; 5 | orem ar 33 RES arse [2 +2 1ST @ a en 05 Po SSret ete so 1Y ensi fe SoZ ra HIRO ar] © 4 2H F is] Oe iter @\z qi pels Bg oa | egret et ar T2PS|e [817 ” nstews 128025} reo roe [4 IGT 1S fae Fat 9 % ars) eros Fa FT 7 - rr Echt 8] owe Ft = 8 8 Far 10 ne ECG are mi tt ee ECAS— Bir rosa [3 Te ef tat CAG. ars PIOBA ML Prose PSE RIT ih em Eto risa PS iT set coo 1 Poza FS TDoat ver oth coe Ear Plo FS TP 34 5 a H 25 oes rook 1 o Ee 5 oe B * ver Yen ao Pst 5 oe sr os 2 sf? soa Loma [2 #530 ery | 086 vee T, E TP a Ecor 87 C52 1TH Ly em [2 1b ime cNeA
- intavais oo fe TT | pen B OS ae are 15 1095 qc = a ips S-BRP4iA-k we ft ence [2 | ne) st fo ws} TE 1 29 1¥ gle LY es [ez 1 £0 TT er] @ se es vee em Soret ot wal 0 D3 + Hy eves [2 OPS aa wa TS wvizon [Pig]? _o jes He kK | ow b aio of wee @ wo S#— a J] ee 1022 ‘TOAL386T ee svscux von fof ™ 1 4 ox 82 —H ee po ws 3 Tob smc _2 Fi S aves § ow vs os mB $1 cxae veer 22 +4 1 i, a CKALGASH 3 i osu ER fp Rs ess ie a 16 Be rest tt 1a? a7 5 0/64 10 Hl Fa dew, me om cen Se 3] aw cout Fann ag ‘Tew fe ‘oun 06 E 19. VOTO ee af fice 22 —_T awe 2,0 PEP aban pout [2 ‘ asym 1 oe 4 v R39 19 TRIOS 226/4y 1 nd 21 ssa Fiera. (aes Sh Sa Pid sein evur f22 col =m os we re bee cee ast i 3, Lew eS ep oe 1 Et ais soa aL 108 [1000 AGO AGS AGD3 aT om Your oe i cud E L vor 41 +44 te say 4 rs 10] an Zs cout LS 829 ay 20/0 ena fe var en cot " e Tt wero Re O21 cite ws90 wei ‘ kas 0 veh tn wee mo—2] wor a aL lee ts moun 1 = h Pareies wes PS oh 24 ison. 1 Pe en2 wa Ti R12 ee ens pai 2x FIMO, oes one 18 ee ee ee = core RIS6 NOT USED eyo NS ons fe Ese] te rae mare 2 Tis MISS RISE 1024 12s | aise weet Fi ou sory $f oho eh 74M rawen, | M0 wee E+ | ore @ =m SNe 38 « re 39 ens [2 wee} 1 | —? a gatise. iT 5] FO 187 C126 5 eo b +2 [sho mT ws on Sat eu ET £28 Tr seo. it | Sse 12 ews [2] Fo reso Ht Se or ne a 14 ®@ SERIAL LF 8. A | B | c | D | E E | & | H
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
- CIRCUIT 30ARD DIAGRAMS
-- 9-1. Main Circuit Board
i139 . . 6837-11493 IC BD SATURN MAIN VAO PAL 171-6963B PC BD SATURN MAIN VAO PAL Zz ; SEGA ve 2 <9 ©seca 1995 ° MADE IN JAPAN “2
¥ CNO aan] amma | BETES dials) 14! 4: 389 . ye 1 94V=0
1234 54: S
© L —
6 Satan Pies ogg Par @secn = SAV 0 ol 588 “rg 839-0750 yor {_ i canis a Se a Sa a
A {1 B |
Tres TP1e . TRSOZTy : ' soz wer
7 a Rize 33 TR2 tre Cy 4 2 a Ao : ‘ 3 | UE . to Tree 70 = CI
- 4 cee Sopris SBS praise B vo PRtosf BSF SSs Fiz & : o136 yt gta] CST Teies . . Cl cet C4 fe Q RI1g2- C7 . * Be .
. e205
is] ©seoa 1988 171-69678 an: sae PC_BD SATURN R.SW_VAD PAL i é a es = ra 0 1995 SEGA Rep vad PAL
- 92. SH-1 Circuit Board
- PARTS SPECIFICATIONS
1c1/2 IC HD6417095F28 QFP HITACHI Parts No. : 315-0922A \G HD6417095SF28 QFR HITACHI Parts No. : 315-0998
Top View 108 73
p72 = ! ! HD64170985 i i ! 2 ! Fb a7
1 36
ll Description
No. vO Pin Name Function 1 Dil 2 yO D12. Data bus 3 D13 3 4 = VCCI Power supply (SV) 5 10 D4 Data bus 6 = VSS1 Power supply (OV) 7 DIS 8 DI6 7 9 yo DI7 Data bus
- 10 Dis. i Dio 12 = VCC2 Power supply (SV) 13 Te) D20 Data bus 14 = VSS2 Power supply (OV) 4 1S D21 16 Tie) D22 Data bus 17 D23 18 = VCC3 Power supply (5V) 19 ie) D24 Data bus 20 = VSS3 Power supply (OV) i 21 D2s 22 oO D26 Data bus 23 D27 24 = VvCC4 Power supply (SV) 25 [fe D28 Data bus 5 26 = VSS4 Power supply (OV) 27 D29 28 ie) D30 Data bus 29 D31 30 AO 31 yo Al Address bus [— 32 A2 7 33 = VSSS Power supply (OV) 34 A3 35 A4 36 AS 6 7 i) 3 ——{ Address bus
38 A7 30 AB - 40 = CCS Power supply (SV)
A B
—-31- — 32-
No. vo Pin Name Function 41 vO Ad Address bus 42 = VSS6 Power supply (OV) 43, Al0 44 All 45 Tie) Al2 Address bus 46 Al3 47 Al4 48 = VOCE Power supply (5V) 49 VO AIS Address bus 50 = VSS7 Power supply (OV) 51 Al6 52 1/0 Al7 Address bus 53 Alg 54 = VCC7 Power supply (SV) 55 ie) Ald Address bus 56 - VSS8 Power supply(OV) 57 A20 58 ie) A2l Address bus 59 A22 60 = VCC8 Power supply (SV) 61 VO A23 Address bus 62 = vss Power supply (OV) 63 A24 64 vO A25 Address bus 65 A26 66 {e) DACKO DMACO acknowledge 7 = VECO Power supply (5V) 68 fe) DACK1 DMAC1 acknowledge 69 = VSS10. Power supply (OV) 70 T DREQO DMACO request 7 1 DREQI DMACI request 72 fe) C86 Chip select 0 73 s) CSL Chip select 1 74 fe) CS2 Chip select 2 75, (e) Cs3 Chip select 3 76 ie) BS Bus cycle start 77 0 RDAWR Read/write 78 - VSS11 Power supply (OV) 79 ie) RAS, CE RAS for DRAM/SDRAM, CE for PSRAM 80 {e) CAS, OE CAS for SDRAM/OE for PSRAM 81 [e) CASHH, DOMUU, WE3 | Each memory most significant byte select signal 82 [e) CASHL, DOMUL, WE2 | Each memory 2nd significant byte select signal 83 {eo} CASLH, DWMLU, WE! | Each memory 3rd significant byte select signal 84 = VCC10- Power supply (SV) 85 0 CASLL, DOMLL, WEO | Each memory least significant byte select signal 86 = VSS12 Power supply (OV) 87 [e} RD. Read pulse 88 {e) CKE SDRAM clock enable control 89 I WAIT. Hardware wait request 90 [) BEN Reserve 91 = VSS13 Power supply (OV) 92 I BACK, BRLS Bus right permission in slave mode/Bus right acknowledge in master mode. 93 (9) BREQ, BGR Bus right request in slave mode/Bus right acknowledge in master mode 94 fe) WDTOVF Watch dog timer output 5 o) FTOB, Free-running timer output B 96 - VCCI1 Power supply (5V) 97 {e) FTOA Free-running timer output A 98 = VSSI4 Power supply (OV) 99 I FTI Free-running timer input 100 1 FTC! Free-running timer clock input 101 I RXD. Serial data input 102 o) TXD Serial data output 103 Wis) SCK Serial clock input/output
No. vo Pin Name Function | 104 = VCC(PLL)12 Power supply (5V) of built-in PLL 105 1 MDO Operation mode pin_ 106 = VSS(PLL)I5 Power supply (OV) of built-in PLL 107 I MDI Operation mode pin a ° a External capacitor connection pin for PLL 110 I MD2 Operation mode pin ean fe) CKPACKN, Clock pause acknowledge output 112 1 CKPREON, Clock pause request input 113 = VCC13 Power supply (SV) 14 = N.C Not connected. 115 = VSSI6 Power supply (OV) 116 - NC Not connected. 17, 1 MD3 Operation mode pin 118 Me) CKIO System clock input/output
i 2 1 wee Operation mode pin
121 = VSSI7 Power supply (OV) 122 i RES Reset 123 = VCC14 Power supply (SV) 124 0 TVECF _ Interrupt vector fetch cycle 125 1 NMI Non-maskable interrupt request 126 IRL3
im I ne External interruput factor input
129 IRLO- _ v0 Eg Data bus 132 = VCC1S Power supply (SV) 133 VO D2 Data bus 134 = VSS18 Power supply (OV) 135 D3 = se) Pe Data bus 138 D6 139 = VCCI6 Power supply (5V) 140 vO D7 Data bus 141 = VSS19 Power supply (OV) 142 D8 143 vO D9 Data bus 144 DIO
Mi Block Diagram
p MULT ® s a Pa Ko cPU cacHeTAG [71 8 | |B aig = <
Oo; |e EXCEPTION g PROCESS 1 1}? INTERRUPT al CACHE CONTROLLER 3 ( } CONTROLLER fej
- 16-bit i IFREE-RUNNING| z TIMER qi wi ¥ 4 2 —— =| 3 S| oa rn CACHE CO BREAK Fa g SERIAL DATA \ CONTROLLER 5 £ cOMMUNI-
- [a] CATIONS K-32 < INTERFACE la = g < < a Q ee c 2 < w £ a a z < 7 Fs VECTOR ADDRESS zLis c pivu gl. ¢ a z WATCH DOG 8 TIMER 2[|2 ia
& foo 8 rE BUS STATE e piReEcT [——1= CONTROLLER MEMORY ACCESS CONTROLLER OPERATION (X2 CHANNELS)| MODE CONTROLLER OSCILLATOR
EXTERNAL BUS INTERFACE
1C3/4/11 4-Mbit SDRAM IC HM5241605TT-17 TSOP IC UPD4504161G5-A12 TSOP IC _HM5241605TT-15 TSOP Parts No. : 315-0928-17 Parts No. : 315-1022-12 Parts No. : 315-0928-15
Wi Top View & Pin Layout @ Pin Name Vee Et] Vss Pin Name Function yoo [2| lg 17015 “Address lapure 8 1/0: inpul maes ar o-a9 Row addresses AO-A8 cc vor ~ Column addresses AO-A7 woo [5] Bs Bank select address A9 vos [6] 5] vO12 Vgc [7] Vec@ 1/00-1/O15 Data inputs/outputs vos [5] fag] vO cs Chip select vos [B| laa ¥O10 RAS Row address strobe command Vss0 fg Hal Vaso CAS ‘Column address strobe command vos fii] yoo 7 + wor fi2| yO8 WE Write enable Voc ps3} Voc DOMU High-order byte input/output mask Damt [il NC DOML Low-order byte input/output mask WE fi g DOMU 5 Si CLK CLK Clock input FAS CKE CKE Clock enable sit NC Veo Power supply As [ig 3GND Vs Ground ne = Eq ead VecQ Power supply of I/O pins ai Be Ba ae VseQ Ground of I/O pins Az gl AS NC Not connected A3 Bal Aa Voc Vss Mi Block Diagram ‘AO - AS
Ao - A7 AO - Ag COLUMN ADDRESS COLUMN ADDRESS ROW REFRESH COUNTER BUFFER ADDRESS COUNTER
ROW DECODER i i ROW DECODER CL. |
MEMORY ARRAY BANK O MEMORY ARRAY BANK 1 512 x 256 x 16 bit 512 x 256 x 16 bit
COLUMN DECODER
ENSE AMPLIFIER & 1/0 BUS|
ENSE AMPLIFIER & 1/0 BUS)
+ CONTROL LOGIC &
INPUT OUTPUT TIMTING GENERATOR
BUFFER BUFFER J I ] J J J J ¥ w 223 Woo = 015 eg BREER ss og
IC5 SCU (Custom Gate Array) IC CUSTOM CHIP SCU QFP Parts No. : 315-5688 Wi Top View Mi Block Diagram
CPU
uF
DSP
Description No. fe) Name Function 1 = VSS GND 2 1/0 AD4 A-bus data bit 4 3 Hie) ADS - A-bus data bit 5 4 ie} AD6 A-bus data bit 6 By vO AD7 A-bus data bit 7 6 yO AD8 A-bus data bit 8 7 VO AD9 A-bus data bit 9 8 ie) ADIO A-bus data bit 10 9 = VDD Power supply +5V 10 lo ADI1 A-bus data bitl1 ul = VSS GND 12 ie) ADI2 A-bus data bit 12 13 vO ADI3 A-bus data bit 13 14 ie) ADI4 A-bus data bit 14 15 ie) ADIS A-bus data bit 15 16 is) AAO A-bus address bit 0 17 {e) AAL A-bus address bit 1 18 QO AA2 A-bus address bit 2 19 = VSS GND 20 (9) AA3 A-bus address bit 3 21 cal VDD Power supply +5V 22 [) AA4 A-bus address bit 4
No. ie} Pin Name Function 23 (e) AAS A-bus address bit 5 24 {e) AAG A-bus address bit 6 25 is} AA7 A-bus address bit 7 26 [e} AAS A-bus address bit 8 27 = VSS GND 28 ie) AAQ A-bus address bit 9 29 {eo} AAI0 A-bus address bit 10 30 fe} AAI A-bus address bit 11 31 = VDD Power supply +5V 32 ° AAI2 A-bus address bit 12 33 (9) AAI3 A-bus address bit 13 34 [e} AAI4 A-bus address bit 14 35, = VSS GND 36 i) AAIS A-bus address bit 15 37 [e) AAI6 A-bus address bit 16 38 fe} AAI7 A-bus address bit 17 39 {@) AAI8 A-bus address bit 18 40 ®) AAID A-bus address bit 19 41 = VDD Power supply +5V 42 () AA20 A-bus address bit 20 43 ~ VSS GND 44 [e) AA21 A-bus address bit 21 4S () AA22 A-bus address bit 22 46 [) AA23 A-bus address bit 23 47 {9} AA24 A-bus address bit 24 48 (9) AFCO A-bus function code bit 0 49 {e) AFC] A-bus function code bit 1 50 {) AAS, A-bus address strobe 31 io) ACSO ‘A-bus chip select 0 52 = VSS GND $3 [e) ACSI. A-bus chip select 1 54 (s) ACS2. A-bus chip select 2 55 = VDD Power supply +5V 56 I AWAIT. A-bus external wait 57 1 AIRQ ‘A-bus external interrupt factor 58 T TEST Test mode selection (normally, input “H”) 59 [e) ARD. A-bus read pulse 60 {e} AWRU A-bus byte 0 (AD15-~8) write pulse 61 [e) AWRL A-bus byte 1 (AD7-0) write pulse 62 = VSS GND 63 (e) ATIMO A-bus extemal access timing 0 64 {e) ATIMI A-bus extemal access timing | 65 fe) ATIM2, A-bus extemal access timing 2 66 fe) BDO B-bus address/data bit 0 67 yo BDI B-bus address/data bit 1 68 ie) BD2 B-bus address/data bit 2 a = VDD Power supply +5V 70 fe) BD3 B-bus address/data bit 3 7 = VSS GND 72 ie) BD4 B-bus address/data bit 4 73 ie) BDS B-bus address/data bit 5 74 fe) BD6 B-bus address/data bit 6 75 VO BD7 B-bus address/data bit 7 76 iffe) BD8 B-bus address/data bit 8 77 yo BD9 B-bus address/data bit 9 78 [e) BDIO B-bus address/data bit 10 9 = VDD. Power supply +5V 80 ie) BDI B-bus address/data bit 11 81 - VSS GND 82 VO BDi2 B-bus address/data bit 12 83 ie) BD13 B-bus address/data bit 13 84 iffe) BDI4 B-bus address/data bit 14
No. ie) Pin Name Function, 85 vO BDIS B-bus address/data bit 15 86 I TROL. Light pen interrupt 87 1 IRQV VDP2¢V blank interrupt 88 i VDP2+H blank interrupt 89 I VDP? data ready 90 (e) VDP2 chip select 91 e) B-bus address/data switching signal 92 = GND 93 fe) B-bus data enable 94 = +5V Power supply 95 {e) SCSP chip select 96 T SCSP data ready 97 1 SCSP interrupt 98 ) VDPI chip select 99 i VDP I data ready 100 i VDPI interrupt 101 We) C-bus address bit 0 102 ie) C-bus address bit 1 103 ie) C-bus address bit 2 104 = GND 105 = +5V Power supply 106 Me) C-bus address bit 3 107 ie) C-bus address bit 4 108 We) C-bus address bit 5 109 ie) C-bus address bit 6 110 = GND 1 Me) C-bus address bit 7 112 YO C-bus address bit 8 113 We) C-bus address bit 9 114 VO C-bus address bit 10 15 ~ GND 16 VO C-bus address bit 11 7 = +5V Power supply 18 ie) C-bus address bit 12 9 i) C-bus address bit 13 120 1/0 C-bus address bit 14 121 = GND 122 ie) C-bus address bit 15 123 ie) C-bus address bit 16 124 10 C-bus address bit 17 125 vO CA18 C-bus address bit 18 126 vO CAI9 C-bus address bit 19 127 = VDD +5V Power supply 128 ie) CA20 C-bus address bit 20 129 = VSS GND 130 tie) CA21 C-bus address bit 21 131 VO CA22 C-bus address bit 22 132 Tie) CA23 C-bus address bit 23 133 ie) CA24 C-bus address bit 24 134 ie) CcDO C-bus data bit 0 135 ie) CDI C-bus data bit 1 136 ie) CD2 C-bus data bit 2 137 = VSS GND 138 fe) CD3 C-bus data bit 3 139 = VDD +5V Power supply 140 iffe) cbD4 C-bus data bit 4 141 ive) CDS C-bus data bit S 142 1/0 CD6 C-bus data bit 6 143 1/0 CD7 C-bus data bit 7 144 = VSS GND 145 ie) CD8 C-bus data bit 8 146 Tie) CD9 C-bus data bit 9
No, vo Pin*Name Function 147 fe) CD10 C-bus data bit 10 148 ie) CDi C-bus data bit 11 149) = VDD +5V Power supply 150 ie) CD12 C-bus data bit 12 151 = VSS GND 152 ie) CD13 C-bus data bit 13 153 ie) CD14 C-bus data bit 14 154 We) cbis C-bus data bit 15 155 We) CD16 C-bus data bit 16 156 1/0 CD17 C-bus data bit 17 157 = VSS GND 158 1/0 CD18 C-bus data bit 18 159 ie) CDI9 C-bus data bit 19 160 = VDD. +5V Power supply 161 1/0 CD20 C-bus data bit 20 162 vO CD21 C-bus data bit 21 163 1/0 CD22 C-bus data bit 22 164 = VSS GND 165 rie) CD23 C-bus data bit 23 166 ie) CD24 C-bus data bit 24 167 vO CD25 C-bus data bit 25 168 ie) CD26 C-bus data bit 26 169 1/0 CD27 C-bus data bit 27 170 = VDD +5V Power supply 171 Te) CD28 C-bus data bit 28 172 = VSS GND 173 iis) CD29 C-bus data bit 29 174 ie) CD30 C-bus data bit 30 175 ie) CD31 C-bus data bit 31 176 I CCST C-bus chip select I 177 I CCS2 C-bus chip select 2 178 oO CCs3. C-bus chip select 3 179 = VSS GND 180 I RESET Initial reset 181 I CLK28 System clock 182 ie) CRDWR C-bus read/write 183 I CRD C-bus read pulse 184 = VDD +5V Power supply 185 ie) CDQMUU. SDRAM byte 0 (CD31-24) write pulse 186 ie) CDOMUL. SDRAM byte 1 (CD23-16) write pulse 187 ie) CDQMLU SDRAM byte 2 (CD15-8) write pulse 188 ie) CDOMLL SDRAM byte 3 (CD7-0) write pulse 189 = VSS GND 190 [e) RAS. SDRAM RAS 191 (9) CAS. SDRAM CAS 192 [e) CWAIT. C-bus extemal wait 193 = VDD +5V Power supply 194 I CIVECF C-bus interrupt vector fetch sycle 195 () CIRLO C-bus extemal interrupt factor 0 196 {e) CIRLI C-bus external interrupt factor 1 197 oO CIRL2 C-bus extemal interrupt factor 2 198 fe) CIRL3 C-bus extemal interrupt factor 3 199 = VSS GND 200 Q CBREQ. C-bus right request 201 1 CBACK C-bus right acknowledge 202 1 MIREQ ‘System manager interrupt 203 [e) AA25 A-bus address bit 25 204 yO ADO A-bus data bit 0 205 ie) ADI A-bus data bit 1 206 ie) AD2 A-bus data bit 2 207 ie) AD3 A-bus data bit 3 208 = VDD +5V Power supply
icé6é DCC IC CUSTOM CHIP DCC QFP. Parts No. : 315-5778 Wi Top View
Pin Name No. vo Name No. ie) Name No. vo Name 1 1 TESTI 35, I AD 69 I WEO 2 ° TESTO 36 I Al0 70 = VSS 3 e) BEN 37 I All 1 Oo BACK 4 oO BDIR 38 1 Al2 72 ° EXBACK 5 - VSS 39 I Al3 B S) BRLS 6 oO DAO 40 = vss 74 = VSS 7 Oo DAI 4l - VDD 15 i BGR 8 oO DA2 42 1 Al4 76 1 BREQ 9 oO DA3 43 I AlS 77 1 EXBREQ 10 oO DA4 44 I Al6 8 ° MFT1 u ° DAS 45 I Al7 79 ° SFTI 12 oO DA6 46 I Al8 80 = VDD 13 re) DA7 47 I Alg 81 1 CK 14 ° DA8 48 I ‘A20 82 - VSS 15 - VSS 49 1 A2i 83 I RESET 16 - VDD 50 I A22 84 1 BS 7 ° DRASO 51 I A23 85 I EWT 18 ° DRASI 52 I A24 86 (e) TOCE 19 O) DRAS2 53 - VSS 87 ) EXTCEO 20 ° DRAS3 54 oO TREQI 88 oO EXTCEI 21 ° DUCA 55 ° TREQ2 89 fe) EXTCE2 22 ° DLCAS 56 - VDD 90 = VSS 23 Oo DWE 37 i IVECF 91 - VDD 24 oO DOE 58 I RDWR 92 i HINT 25 - vss 59 1 RD 93 1 VINT 26 = VDD 60 - VSS 94 I DECON 27 I Al 61 1 Cs2 95 oO ROMCE, 28 I A2 62 1 csi 96 Oo SMPCCE 29 i A3 63 1 fese] 97 {) SRAMCE, 30 i A4 64 () WAIT 98 fe) MOE 31 I AS 65 - VDD 99 oO MWR 32 1 AG 66 - VSS 100 - VSS 33 I A7 67 I WTIN 34 1 Ag 68 1 WE!
1C7 IPL ROM OS SATURN IPL-ROM PAL DIP Parts No. : EPR-17933 Parts No. : MPR-17933 Wi Top View & Pin Layout Pin Name
AO-A17 Address inputs CE Chip enable OE Output enable GND Ground
BYTE
DO-D15 Data inputs/outputs Voc +5V power supply
1C8 BACKUP RAM IC CXK58267AM-10L SOP IC UPD43257B-10LL SOP IC M5M5255BFP-12LL SOP Parts No. : 315-0948-10 Parts No. : 315-0930-10 Parts No. : 315-0964-10
1C SRM20257LLM10 SOP IC UM62257M-70LL SOP Parts No. : 315-0965-10 Parts No. : 315-1002-70
Bi Block Diagram @ Top View & Pin Layout a V, x 8 Vcc A14 O Pee WE A1is0—| f° Ql Ais Aizo—|| « © Vec As AO | ¢ : ° | Memory Ao Aavo—|| BUFFER| © |occoben| @ | MATRIX att aso—|| * ° o | st2xsi2 cee aro—||e [-—o GND ‘Ato Aso— | te As O—L iT @ vos La gl 07 eee vos @ vos Ai0 OF oa mol As014 | VO GATE ol BUFFER COLUMN a A2O1+ | © DECODER @ Description Arot | Ao > Name Function a A0-Al4 ‘Address inputs eee 1/01-1/08 Data inputs/outputs BUFFER CEI, CE2 Chip enable inputs WE oO} — VO BUFFER: WE Write enable input vi +5V power supply Eto a J J cc po PI CE2 ©. ) vO1 vos GND Ground
~ 42—
ico SMPC IC CUSTOM CHIP SMPC QFP Parts No. : 315-5744
i Top View
Poss] g
@ Description No. vo | Name Function No. vO Name Function 1 R70 33 PIOOA
- Not connected. 2 R71 34 PIOIA 3 R72 yo Reset control 36 PIO2A 4 R73 36 yO PIO3A | Control pad 5 R50 37 PIO4A 6 RS1 oe 38 PIOSA 1 Jumper configuration input 7 RS2 39 PIO6A 8 RS3 40 PIOOB 9 - TEST Not connected > GND 4) PIOIB Te) OSC1 Clock 3 42 PIO2B 11 OSC2 43 yO PIO3B_ | Control pad 12 - GND Ground 44 PIO4B 13 X2 4 se) Clock 4 5 PIOSB 14 XL 46 PIO6B 15 RESET | Master reset input 47 I EXL Input 16 - VCC Power 48 I INTO/D13 | Input 17 qT cs Chip select input 49 INT2/RO1 | Backup RAM reset control 18 1 RW ite i JW Read/write input 50 10 Do Reset control 19 Al 51 Di 20 A2 52 - D2 Not connected. 21 53 vO AP | sddress bus D3 22 A4 54 D4 23 AS 55 DS 24 A6 56 D6 lo Reset control 25 DBO 37 I! jo 26 DBI 58 Ds 27 DB2 59 D9 28 DB3 DIO yo Data bus kad 29 DB4 61 R60 yo Reset control 30 DBS 62 R61 31 DB6 63 R62
- Not connected. 32 DB7 64 R63
1C10 VDP1 ; IC CUSTOM CHIP VDP1QFP = IC CUSTOM CHIP VDP1 S QFP Parts No. : 315-5689 Parts No. : 315-5883
Hi Top View 126 85
1271 Fpe4 i i i i i i 168 i bas
1 42
i Description
No. ie) Name Function 1 = NC Not connected. 2 VRAMA7 3 fe} VRAMA8 Address bus (VRAM) 4 VRAMA9 5 - VSS Ground for I/O pin 6 {e) VCLK Clock (VRAM) 7 (o) VUDOM, Upper byte input/output mask(VRAM) 8 {e) VLDOM. Lowerbyte input/output mask(VRAM) 9 = VSS Ground for internal circuit 10 le) VCASN. Column address asserted (VRAM) i o) VRASN. Row address asserted (VRAM) 12 = VCC Power supply 13 {e) VWEN. Write enable (VRAM) 14 (e) VCSN Chip select (VRAM) 15 i MCLK Master clock 16 = RESEIN. Reset 17 - VSS. Ground for I/O pin 18 > CSN Chip select 19 = ADN. Address/data select 20 = DTEN Data enable 21 {e) TRON Interrupt request 22 (9) READYN Ready 23 VBUSO 24 oO VBUS1 Address/data bus (Syscon) 25 VBUS2 26 = VSS Ground for I/O pin 27 VBUS3 28 VBUS4 29 oO VBUSS Address/data bus (Syscon) 30 VBUS6 31 VBUS7
- = VCC Power supply 33 VBUS8 # oO ae Address/data bus (Syscon) 36 VBUSI1 37 = VSS Ground for internal circuit 38 VBUS12 39 fe) VBUS13 Address/data bus (Syscon) 40 VBUS14
No. vo Name Function
- {e) VBUSI5 Address/data bus (Syscon) 2 - xe Not connected. 44 FOAO 45 fe} FOAL Address bus (FBO) 46 FOA2 47 = VSS Ground for 1/O pin 48 ie) FOA3 Address bus (FBO) 49 fe) FOA4 Address bus 30 ie) FOAS Frame buffer (FBO) 51 fe) FOA6 Address bus (FBO) 352 = VCC Power supply 53 FOA7 54 oO FOA8 Address bus (FBO) 55 FOA9 56 [e) FOCSN Chip select (FBO) 57 = VSS Ground for intemal circuit 58 ie) FOWEN Write enable (FBO) 59 {e) FOCLK Clock (FBO) 60, e) FRRASN Row address asserted (FBO) 61 [e) FOCASN Column address asserted (FBO) 62 [e} FOLDOM. Lower byte input/output mask (FBO) 63 [e) FOUDOM. Upper byte input?output mask (FBO) 64 - VSS. Groun for I/O pin
- FODO 66 FODI 67 [e) FOoD2 Data bus (FBO) 68 FOD3 69 FOD4 70 = VSS Ground for internal circuit a FODS z i) 7 Data bus (FBO) 74 FOD8 78 - VCC Power supply 76 FOD9 = fe) poe Data bus (FBO) 79 FOD12
- - VSS Ground for I/O pin 81 FOD13 82 fe) FODI4 Data bus (FBO) 83 FODI5 # - xe Not connected. 86 FIDO 87 fe} FIDI Data bus (FB1) 88 FID2 89 = VSS Ground for I/O pin 90 F1D3 4 ° aD Data bus (FB1) 93 F1ID6 94 = VCC Power supply 95 FID7 2 [s} ae Data bus (FB1) 98 FIDIO 99 = VSS Ground for intemal circuit 100 FID 101 FID12 102 fe} FIDI3 Data bus (FB1) 103 FIDI4 104 FIDIS
No. ie} Name Function 105 = VSS Ground for 1/O pin 106 {e) FICLK. Clock (FB1) 107 {o) FICSN. Chip select (FB1) 108 [e) FIWEN Write enable (FB1) 109 {e) FIRASN Row address asserted (FB1) 110 [e) FICASN Column address asserted (FB1) Mt [e) FILDQM Lower byte input/output mask (FB1) N2 = VSS. Data bus (FB1) 113 {e) FIUDQM. Lower byte input/output mask (FB1) 14 FIAO us ie) FIAL Address bus (FBI) 116 FIA2 17 = VCC Power supply 118 FIA3 119 fe) FIA4 Address bus (FB1) 120 FIAS 121 [e) FIA6 Address bus (FB1) 122 = VSS Ground for I/O pin 123 {e) FIA7 124 ) FIA8 Address bus (BF1) 125 {eo} FIA9
128 = HTIMN. Horizontal sync timing 129 = VTIMN Vertical sync timing 130 {e) V2CLK Video clock (1/2 MCLK) 131 = VSS Ground for I/O pin 132 {e) VOUTO x 3 von Display start address/video data 135 (@) VOUT3, 136 = VCC Power supply 137 fe) VOUT4 Display start address/video output data 138 fe) VOUTS 139 fe) VOUT6 Video output data 140 oO VOUT7 141 = VSS Ground for internal circuit 142 {e) VRAMDO 143 {e) VRAMD1 144 [e) VRAMD2 VRAM data bus 145 [) VRAMD3 146 {e) VRAMD4 147 = VSS Ground for I/O pin 148 {e) VRAMDS 149 [e) VRAMD6 150 [e) VRAMD7 151 ra) VRAMD8 VRAM data bus 152 {e) VRAMD9 153 {e) VRAMDIO 154 = VSS Ground for intemal circuit 155 (e) VRAMDI1 156 [e) VRAMD12 157 i) VRAMD13 VRAM data bus 158 {e) VRAMD14 189 - VCC Power supply 160 {e) VRAMDIS VRAM data bus 161 [e) VRAMAO 162 [e) VRAMAI 163 [s) VRAMA2 164 fe) VRAMA3, VRAM address bus 165 () VRAMA4 166 fe) VRAMAS 167 {e) VRAMA6 168 = NC Not connected.
1012/13/15/16 IC UPD4502161G5-A12 TSOP NEC Parts No. : 315-0910-12 IC HM5221605TT-17 TSOP HITACHI Parts No. : 315-1017-17 IC LC382161T-17 TSOP SANYO Parts No. :315-1012-17
Ii Top View & Pin Layout Pin Name
Vee H] Ed Vss A0-A9 Address inputs Dao | ha Dats DQo-DQ5 Data inputs/outputs dar [3] leg} Daa Vsg Fa] bi Vsg CLK System clock input dae [| fa Dats CKE Clock enable Das [6] les] Dat2 — Veo H] M44] Voc cs Chip select das [a] Bg oats RAS Row address strobe command Das [3] Dato Vg (19) Ere AS Col / address strobe command Das fi] fg Das WE Writre enable baz [ial bq Das Veo Bal Voc DOML, DOMU | DQ mask enable DomL [id B7] NC Vv, 1 WE al Fa pomu ‘oc Supply voltage TAS fig] B5] CLK Vss, GND Ground RAS [7] 4] CKE NC No connection SS fig 3] NC As [i] 84 GND As Bol Bi] GND Ao Bi] 50 A7 At Bal Bo AS a2 Bal Ba] AS A3 Bal 7] Aa Vec B5| BG Vss
i Description No. vO Pin Name Function 4 15, 25, 38, 44, - VCC Power supply of internal circuits.
4, 10, 26, 41, 47,50] — VSS Ground pins.
2, 3,5, 6, 8, 9, 11, 12, 39, 40, 42, 43, se) DQ1-DQI6 1/O pins are the same as conventional DRAM. 45, 46, 48, 49
DQMU controls upper byte and DQML controls lower byte input/output buffers. In read mode, DOMU, DOML control output buffer impedance like conventional OE. If DQMU, DOML is high, output buffers become high impedance. If DQMU, DQML is low, output buffers become low imedance. 14,36 P| BOML, DOMU | tf DOMU, DOML is low, output buffers become low impedance. And when device in write mode, DQMU, DOML contro! word mask. If DQMU, DOML is high input data is not written to memory cell. If DOMU, DOML is low input data is written to memory cell. WE CAS RAS have the same names with conventional DRAM. But these pins 15, 16, 17 1 | WETASRAS | have different definitions with conventional ones. Alll of these pins only define command cycle definition. For detail information see command table.
CS low start the command input cycle. When CS is high, all input are not 18 i cs referenced. But even if CS is high, internal operations i.e, bank active or burst are not changed. 19 I AQ AQ is bank select signal (BS). In command cycle, A9=low select bank A and AQ=high select bank B.
-~47—
No. vO Pin Name Function
20, 21-24, 27-30 A0-A8 Row address (AXO-AX6, AX8) is determined by AO-A8 level at the bank active command cycle CLK rising edge. (AX7 is don’t care.) Column address (AYO-AY7) is determined by AO-A7 level at read or write command cycle CLK rising edge. And this column address become burst access start address. A8 define precharge mode command cycle, both banks are prechareged. But A8=low in when A8=high in precharge command cycle, only one bank that is selected A9 (BS) is precharged. And when A8=high in read or write command cycle, the precharge cycle start automatically after the last data in burst accessing. 31, 32 GND Ground 33, 37 NC Not connected.
CKE CKE determine next CLK is valid or not. If CKE is high next CLK rising edge is valid. But if CKE is low, next CLK is invalid. If CLK rising edge is invalid, intemal clock is not asserted and 2 PD4504161 becomes halt operation. And when 42 PD4502161 does not in burst mode and CKE is negated, 1 PD4502161 enter power down mode. During power down mode CKE must keep low level.
CLK CLK is the master clock input pin. The other inputs signals are referenced at CLK rising edge.
1C14 VDP2 IC CUSTOM CHIP VDP2 QFP YAMAHA
Parts No. : 315-5690 IC CUSTOM CHIP VDP2 QFP HH
Parts No. : 315-5690-02 Parts No. : 315-5890
I Top View Ml Block Diagram 120 81 SCU
(— >) VDP2
Bus control HNV counter & timing generator
160 Scroll picture block Video process Normal Rotation picture picture Color offset Output data coordinate coordinate ——y & shadow control calculation calculation
Pattern Color name Window computing Color RAM control control
Character Line picture Priority Color RAM control control control contro!
VRAM ff Dot data Sprite control contro! control
XN / VRAM Expanded - VDP1 picture circuit IC CUSTOM CP VDP2 S QFP YAMAHA
RGB encoder
No. vO *Pin Name Function 1 e) RBCS VRAM-B chip select 2 ie) RBRAS. VRAM-B row address strobe 3 {e) RBCAS VRAM-B column address strobe 4 (e) RBWE. VRAM-B write enable 5 = VSS GND 6 fe) RBLDM VRAM-B DQ low-order mask enable 7 fe) RBUDM VRAM-B DQ high-order mask enable 8 {e) RBAO VRAM-B address bit 0 9 {eo} RBAI VRAM-B address bit 1 10 = VDD. +5V power supply ll [e) RBA2 VRAM-B address bit 2 12 oO RBA3 VRAM-B address bit 3 13 fe) RBA4 VRAM-B address bit 4 14 fe) RBAS VRAM-B address bit 5 15 = VSS GND 16 ie) RBA6 VRAM-B address bit 6 17 [e) RBA7 VRAM-B address bit 7 18 {e) RBA VRAM-B address bit 8 19 {e) RBAQ VRAM-B address bit 9 20 ie) VDO SYSCON interface data bit O 21 ie) VDI SYSCON interface data bit 1 22 VO VD2 SYSCON interface data bit 2 23 10 VD3 SYSCON interface data bit 3 24 = VSS GND 25 ie) VD4 SYSCON interface data bit 4 26 ie) VD5 SYSCON interface data bit 5 27 ie) VD6 SYSCON interface data bit 6 28 yO VD7 SYSCON interface data bit 7 29 = VDD “+5V power supply
- ie) VD8 SYSCON interface data bit 8 31 ie) VD9 SYSCON interface data bit 9
- vO VD10 SYSCON interface data bit 10 33 We) VDI SYSCON interface data bit 1] 34 yO VD12 SYSCON interface data bit 12 35 Te) VD13 SYSCON interface data bit 13 36 = VSS GND 37 ie) VD14 SYSCON interface data bit 14 38 VO VDIS SYSCON interface data bit 15 39 I AD. SYSCON interface address/data selection 40 I DTEN SYSCON interface data enable 41 fe) READY. SYSCON interface data ready 42 I cs SYSCON interface chip select 3 = VDD +5V power supply 44 [e) VINT ~ SYSCON interface vertical interrupt 45 [e) HINT SYSCON interface horizontal interrupt 46 I EXLAT. Extemal latch strobe input 47 I EXSYN External sync signal input 48 ie) EXBGO External input data bit 0 / Test input/output (in test mode) 49 ie) EXBG1 Extemal input data bit 1 / Test input/output (in test mode) 50 ie) EXBG2 Extemal input data bit 2 / Test input/output (in test mode) 51 ie) EXBG3 External input data bit 3 / Test input/output (in test mode) 52 - VSS GND 53 VO EXBG4 External input data bit 4 / Test input/output (in test mode) 54 ie) EXBGS External input data bit 5 / Test input/output (in test mode) 55 VO EXBG6 External input data bit 6 / Test input/output (in test mode) 56 ie) EXBG7 External input data bit 7 / Test input/output (in test mode) 57 VO EXBG8 External input data bit 8 / Test input/output (in test mode) 58 ie) EXBG9 External input data bit 9 / Test input/output (in test mode) 59 1/0 EXBG10 Extemal input data bit 10 / Test input/output (in test mode) 60 1/0 EXBGI1 External input data bit 11 / Test input/output (in test mode) 61 ie) EXBG12 External input data bit 12 / Test input/output (in test mode) 62 ie) EXBG13 External input data bit 13 / Test input/output (in test mode) 63 ie) EXBG14 External input data bit 14 / Test input/output (in test mode)
No. vo _Pin Name Function 64 vO EXBGIS Extemal input data bit 15 / Test input/output (in test mode) 65 VO EXBG16 External input data bit 16 / Test input/output (in test mode) 66 1/0 EXBG17 External input data bit 17 / Test input/output (in test mode) 67 = VSS GND 68 ie) EXBGI8 Extemal input data bit 18 / Test input/output (in test mode) 69 1/0 EXBG19 Extemal input data bit 19 / Test input/output (in test mode) 70 vO EXBG20 External input data bit 20 / Test input/output (in test mode) 71 VO EXBG21 External input data bit 21 / Test input/output (in test mode) 72 VO EXBG22 External input data bit 22 / Test input/output (in test mode) 73 ie) EXBG23 External input data bit 23 / Test input/output (in test mode) 74 I EXON External input data display timing 5 = VDD +5V power supply 76 I CLK Main clock input 77 () EXSL External video select signal 7B 1 RESET. Initial reset input 79 1 NTSC NTSC/PAL selection 80 = VSS GND 81 = AVSS GND of linear RGB 82 (e) R Linear R output 83 fe} G Linear G output 84 {e) B Linear B output 85 = AVDD. +5V power supply of linear RGB 86 {e) CSYNC. Composite sync signal output 87 0 VSYNC. Vertical sync signal output 88 oO HSYNC Horizontal sync signal output 89 = VDD +5V power supply
- [e) DCLK Dot clock output 91 {e HTIM VDP! interface H timing 92 ( VTIM., VDPI interface V timing 93 ie) FBDO VDP1 interface data bit 0 94 ie) FBDI VDP1 interface data bit 1 95 [ie FBD2 VDP1 interface data bit 2 96 1/0 FBD3 VDP1 interface data bit 3 97 - VSS GND 98 vO FBD4 VDP} interface data bit 4 99 ie) FBDS VDP} interface data bit S 100 VO FBD6 VDP!1 interface data bit 6 101 VO FBD7 VDP! interface data bit 7 102 {3 RAAO VRAM-A address bit 0 103 [e) RAAI VRAM- A address bit 1 104 {e) RAAZ VRAM- A address bit 2 105 fe) RAA3 VRAM- A address bit 3 106 = VSS GND 107 {e) RAA4 VRAM- A address bit 4 108 {e) RAAS. VRAM- A address bit 5 109 {e) RAAG6 VRAM- A address bit 6 10 [e) RAA7 VRAM- A address bit 7 1 = VDD +5V power supply 112 {e) RAAS VRAM- A address bit 8 113 {e) RAAQ VRAM- A address bit 9 114 fe) RACS- VRAMS=A chip select Ls {e) RARAS. VRAM-A row address strobe 116 = VSS GND 117 o) RACAS ‘VRAM- A column address strobe Mg (0) RAWE, VRAM- A write enable 9 {e) RALDM VRAM- A DQ low-order mask enable 120 fe) RAUDM VRAM- A DQ high- order mask enable 121 yo RADO VRAM- A data bit 0 122 i) RADI VRAM- A data bit 1 123 ile) RAD2 VRAM- A data bit 2 124 1/0 RAD3 VRAM- A data bit 3 125 = VSS GND 126 1/0 RAD4 VRAM- A data bit 4
No. fe) Pin Name Function 127 vO RADS VRAM — A data bit 5 128 vO RAD6 VRAM ~ A data bit 6 129 ie) RAD? VRAM — A data bit 7 130 = VDD +5V power supply 131 ie) RAD8 VRAM —| A data bit 8 132 ie) RAD9 VRAM — A data bit 9 133 1/0 RADIO VRAM — A data bit 10 134 yO RADI VRAM — A data bit 1] 135 = VSS GND 136 ie) RADI2. VRAM — A data bit 12 137 (ie) RAD13 VRAM — A data bit 13 138 vO RAD14 VRAM — A data bit 14 139 vO RADIS VRAM — A data bit 15 140 fe) RCLK VRAM — AJB clock 141 I TEST Test mode selection (normally, connected to VDD) 142 1/0 RBDO VRAM — B data bit 0 143 vO RBDI VRAM — B data bit 1 144 ie) RBD2 VRAM —| B data bit 2 145 Oo RBD3. VRAM ~ B data bit 3 146 = VSS GND 147, 0 RBD4 VRAM —~ B data bit 4 148 iffe) RBDS VRAM — B data bit 5 149 ie) RBD6 VRAM — B data bit 6 150 ie] RBD7 VRAM — B data bit 7 151 = VDD. +5V power supply 152 ie) RBD8 VRAM — B data bit 8 153 VO RBD9 VRAM ~ B data bit 9 154 fe) RBD10 VRAM - B data bit 10 155 iffe) RBD11 VRAM — B data bit 11 156 = VSS GND 157 VO RBD12 VRAM — B data bit 12 158 ie) RBDI3 VRAM — B data bit 13 159 VO RBD14 VRAM — B data bit 14 160 VO RBDIS VRAM — B data bit 15
1C17 SCSP IC CUSTOM CHIP SCSP QFP YAMAHA Parts No. : 315-5687
Wi Top View
Fp s4 i ! I
I i i Fb ss
Wi Description No. vO Pin Name Function 1 MCD6 2 ire) oe MCPU data bus 4 MCD3 5 = VSS GND 6 MCD2 7 ie) MCDI MCPU data bus 8 MCDO 9 {e) MCRDYN_ Ready signal to MCPU. 10 [e} MCINTN. Interrupt request to MCPU. i = VDD. Power supply (Sv) 12 I RESEIN. SCSP reset input
- = VSS GND 14 1 MACK SCSP master clock: 512fs (22.58MHz) 15 INT2N 16 I INTIN. SCSP external interrupt request input 17 INTON, 18 = VDD Power supply (5¥) 19 I ESD Digital audio interface serial data input 20 I EBCK Digital audio interface BCK 21 I ELRCK Digital audio interface LRCK 22 I MIDIINP. MIDI input 23 = VSS GND 24 {e) MIDIOUT MIDI output 25 [e) MRASN. RAS signal 26 o) MWEUN Write signal corresponding to MD[15-8] 27 [e) MWELN Write signal corresponding to MD[7-0] 28 MCASON : 39 fe) MCASIN' CAS signal 30 [e) MOEN Sound memory data output enable 31 = VDD Power supply (Sv) 32 MAO 33 MAI 2 oO tas Sound memory address 36 MA4 37 MAS 38 = VSS GND 39 MA6 40 oO MA7 Sound memory address 41 MA8 42 VO MDO Sound memory data
~ 52 —
No. ie} + Pin Name Function, + Tie) Met Sound memory data 45 = VDD. Power supply (SV) 46 MD3 47 MD4
- v0 ws Sound memory data 50 MD? 51 MD8 52 = VSS GND 53 MD9 54 MD10 2 vO au Sound memory data 7 MD13 58 MD14 59 = VDD Power supply (SV) 60 vO MDIS Sound memory data 61 Oo DSD DAC interface serial data output 62 oO DBCK DAC interface BCK 63 {s) DLRCK DAC interface LRCK 64 0 DSCK DAC interface system clock [256fs clock] 65 SCA23 66 SCA22 67 I SCA21 SCPU address bus 68 SCA20. 69 SCA19 70 = VSS GND 71 SCA18 72 SCAI7 73 SCAI6 74 SCAIS 7S 1 SCAI4 SCPU address bus 76 SCA13 77 SCA12 78 SCAL] 79 SCA10 30 = VDD Power supply (5V) 81 SCA9 82 SCA8 83 SCA7 84 SCA6 85 1 SCAS. SCPU address bus 86 SCA4~ 87 SCA3 88 SCA2 89 SCAL 90 = VSS GND 91 SCFCO 92 1 SCFC1 SCPU status input 93 SCFC2 94 1 SCWIN SCPU write 95 I SCLDSN SCPU SCD [7-0] strobe 96 1 SCUDSN. SCPU SCD [15-8] strobe 97 i SCASN SCPU address strobe 98 = TESTN LSI test signal (Not connected) 99 = VDD Power supply (5V) 100 {e) SCDTAKN SCPU data acknowledge. 101 [e) SCAVECN SCPU auto vector interrupu specification 102 SCIPLON 103 re) SCIPLIN SCPU interrupt level specification 104 SCIPL2! 105 ie) SCDO SCPU data bus
No. vO Pirf Name Function 106 10 SCDI SCPU data bus 107 = VSS GND 108 SCD2 109 SCD3 110 ScD4 li yO SCDS SCPU data bus 2 SCD6 113, SCD7 114 SCD8 15 = VDD Power supply (5V) 6 SCD9 7 lO SCD1O SCPU data bus 18 SCD11 119 = VSS. GND 120 SCD12 121 SCD13, 122 ie) SCDI4 SCPU data bus 123 SCDIS 124 = VSS GND 125 I MCCSN. Select signal from MCPU 126 1 MCCK. 28 MHz clock from MCPU 127 = VDD Power supply (SV) _ 128 ie) MCD7 MCPU data bus
IE SCSP Chip Block Diagram
SCPUI (SOUND CPU) LFO (LOW FREQ OSCILLATOR) ‘ALFO PLFO —{|— | mecpur (main CPU) ——— 3
DMA PLFO PG(PITCH GENERATOR) l MIDI ADP (ADDRESS POINTER) L MEMCT EXT(AUDIO INPUT) 7 (MEMORY CONTROLLER) DRAM te fie tie EG (ENVELOPE GENERATOR) INTER EG (INTEPOLATOR) +10 ——* “IEG _ALFOL PCM DATA MULTI (MULTIPLIER)
—____ 16 DIRECT EFFECT OMIX (OUTPUT MIXER)
DAC
1C18 SOUND CPU (68000) IC MC68ECOO0FN12 PLCC MOTOROLA Parts No. : 3
i Top View 15-0941
i Description i Signal Description
: vee ADDRESS BUS ae" A23-A1 ak | ATA BUS —— 'D15-Do BS Foo RW PROCESSOR FC1 ODS ASYNCHRONOUS STATUS {= Foz TDS BUS CONTROL Mce8EC000 [__DTACK
BR BUS Ea ARBITRATION [J CONTROL
SYSTEM RES! CONTROL { HALT <1, INTERRUPT be PLZ__ P contRoL
No. | vO Name Function No. | 1/0 Name Function i = GND 35 | = GND __| Ground 2 D4 36 Ad 3 D3 37 AS 4 | v0 D2 Data bus 38 A6 5 Di 39 A7 6 DO 40 A8 7 AS Address strobe 41 Ad 8 0 UDS _| Upper data strobe 2 Al0 9 LDS. Lower data strobe 43 All 10 RWW __| Read/write 44 | 0 Al2 Address bus ui 1 DTACK | Data transfer acknowledge 45 Al3 12 {e) BG Bus grant 46 Al4 B iI BR Bus request 47 Als 14 48 Al6 i 7 VCC | Power rT) AIT 16 I CLK Clock 50 Als 17 31 Ald 18 - GND Ground 32 Az0 19 I MODE _| 8 bit/16 bit select 53 | — VCC__| Power 20 | VO | HALT | Halt 54 A2l 21_| VO | RESET | Reset 55_| O A22 Address bus 22 | = NC Not connected 56 A23 23 i AVEC 37 | = GND__| Ground 24 i BERR | Bus error 58 Dis 25 IPL2 59 Di4 26 I TPL Interrupt control 60 D13 27 TPLO 61 Di2 28 FC2 62 Dil 29 ie) FCI Processor status 63 | VO DIO Data bus 30 FCO 64 D9 31 AO 65 D8 32 Al 66 D7 3] (0 AD Address bus ro De 34 A3 68 DS
1C19 Sound DRAM IC HM514270AJ-8 SOJ HITACHI Parts No. : 315-0777-80
Parts No. : 315-0822-80
Wi Top View & Pin Layout IC UPD424270LE-70 SOJ NEC Parts No. : 315-0739-70 IC MN414270SJ-08 SOJ PANASONIC IC HM514270A3-7 SOJ HITACHI Parts No. : 315-0777-70
Veo Ef Vss Op [2] A VvOys, v0, [3] g}V0,, in put State utput vo. [a] WOi3 Outpu Operation Mode v0, [5] VO. RAS | CAS | UWE | [WE State Voc [8 Vss H H D D Open __| Standby vo, Z Wy, H L H H Valid __| Standby vos [8] WOy9 L L H H Valid _| Read cycle vo, AOy C L_| £2) [ L2) Open _| Early write cycle YO; fol Vos L L_| £2) [ L2) | Underlined | Delayed write cycle Ne fi Ne L L_[H>L/[H=>L]| Valid | Read modified write cycle TWE fra] NC L H D D Open RAS only refresh cycle UWE fig gears HSL] OL D D Open | CAS before /RAS refresh cycle RAS fi OE L_|H=>L| H H Valid _| High-speed page mode read cycle ne [15 As L_|H=>L}] L2) [ £2) Open _| High-speed page mode early write cycle Ao fg Ay L HL] L2) | L2) | Underlined | High-speed page mode delayed write cycle af As L_ [HSL THC PHL Valid [High-speed page mode read modified write cycle Ao As Note: H=High(inactive), L=Low(active), D=Don’t care. A; fig A, Voc Bi] Vss
1C20 PLL IC CUSTOM CHIP PLL HOFP Parts No. : 315-5746
i Top View
VCOINt Act APOL avoDt
[91071135] DWV.
- DoTcLK
4DIV. FSC | SCPCLK 4 DNV. 2 DV. ces
ar 2 @ snocix ( TEST) jie i
i Description No. Vo Name Function 1 NPSEL NTSC (S5V)/PAL (OV) mode switching control 2 I DOTSEL 320PIX (OV)/352PIX (SV) mode switching control 3 SYSRES Reset (OV reset) 4 TEST Test pin 5 {e} SCPCLK Clock signal output 6 EXTCLK External clock input / CMOS I with pull-down resistor incorporated 3 I oscsw Crystal oscillation/external clock signal input switching control (5V: Crystal oscillation, OV: External clock signal) / CMOS I with pull-up resistor incorporated 8 = DGND Ground of digital circuits 9 oO OSOUT2 Crystal oscillator output (OSC2) / Oscillation output O 10 1 OSIN2 Crystal oscillator input (OSC2) / Oscillation input I lM = OSVDD2 VDD of crystal oscillator (OSC2) 12 ie) PDOUT2 Phase detector (PD2) output
- 1 VCOIN2 VCO? input / Analog | 34 AC2 Phase compensator pin / Analog 15 oO APO2 VCO2 amp output / Analog O 16 = AVDD2 Analog VDD of VCO2 17 vO SNDCLK Clock signal output 18 DOTCLK Clock signal output 19 = AVDD1 Analog VDD of VCO1 20 [e) APO! VCO1 amp output / Analog O 21 = ACL Phase compensator pin / Analog
- 1 VCOIN} VCO1 input / Analog 23 fe) PDOUTI Phase detector (PD1) output 24 = OSVDD1 VDD of crystal oscillator (OSC1) _ 25 I OSINI Crystal oscillator input (OSC1) / Oscillation input 1 26 fe) OSOUTI Crystal oscillator output (OSC1) / Oscillation output O 27 = DVDD VDD of digital circuits 28 ie) FSC Clock output signal
1021 IC CXA1645M SOP SONY Parts No. : 315-5314 Wi Block Diagram GND2 ROUT GOUT BOUT VOUT vcc2 FO YTRAP YOUT COUT VREF = IREF A
75 75 [DRIVER] | [DRIVER| REGULATOR!
[DELAY HeL AMAL} Sop x DELAY HCL AMPLY “agp x L) BPF E = RY Modulator
BY Modulator
cLamP| [cLamP | [CLAMP fsmpuise} | GHASE Lf Puts 4__-4—o oo —O-—_®—_@—_©—_©®-_©—__0—_® )—O- GND1 RIN GIN BIN NC SCIN NPIN BFOUT YCLPC SYNCIN NC vect
@ Description No. vO Pin Name Function 1 _ GND1 Ground of circuits other than RGB, composite video and Y/C output circuits. 2 RIN . + . . . 3 1 GIN nace RGB signal inputs. The signals should be input with 100%=1 Vp-p ‘max.). 4 BIN 5 = NC Not connected. 6 I SCIN Subcarmier input 7 I NPIN NTSC/PAL mode switching pin 8 i) BFOUT BF pulse monitoring output 9 = YCLPC Time constant which determines the Y signal clamp is connected.
- 1 SYNC IN Composite sync signal input. Receives it at the TTL level. u = NC Not connected. 12 = VCC1 Power supply of circuit other than RGB, composite video and Y/C output 13 IREF Pin to determine the internal reference current level. 14 = VREF, Internal reference voltage pin. 15 {e) COUT Chroma signal output. Can drive a 75 Q load. 16 {e) YOUT Y (Juma) signal output. Can drive a 75 Q load. _ Reduces cross-color caused by subcarrier frequency components contained " YTRAP in the Y signal. 18 _ FO Adjusts fo of the internal filter. Connect the following resistor between this pin and ground depending on the NTSC or PAL mode. 19 ~ VCC2 Power supply of RGB, composite video and Y/C output circuits. 20 {e) CVOUT Composite video signal output. This can drive a 75 Q load. 21 BOUT 22 (o) GOUT Analog RGB signal outputs. These can drive a 75 Q load. 23 ROUT 24 = GND2 Ground of RGB, composite video and Y/C output circuits.
1C22 DAC
IC TDA1386T SOP PHILIPS Parts No. : 313-5313
@ Top View @ Description
Voos [7] A No. vO Pin Name Function Vss- [2| ve 1 = VDDA Analog supply voltage Test: [3| B ial 2 = VSSA Analog ground Bek [3] 21] VOR 3 ! TESTI Test input 1; pin should be connected to ground. ws [5] Bg Fitcrl 4 i BCK Bit clock input. para [6 ig Fito. 5 i WS Word select input. oxstt [7] figvo. [6 1 DATA __| Data input. cxstz [a] [td arro [77 i €EKSLI___| Format selection 1. Vss0 [8] sary | 8 1 CKSL2__| Format selection 2. Veen (fo fislapp2 [9 = VSSD Digital ground Test fi] frgarpL [10 = VDDD Digital supply voltage. SYSCLK fi apps [ii T TEST2 Test input 2 ; pin should be connected to ground. 12 = SYSCLK System clock 256 fs 13 I APP3 Application mode 3 input. 14 I APPL Application mode selection input. 15 1 APP2 Application mode 2 input. 16 1 APPI Application mode 1 input. 17 I APPO. Application mode 0 input. 18 {e] VOL Left channel output. _ Capacitor for left channel first-order filter function, should be 19 FILTCL | connected between pins 19 and 18. _ Capacitor for right channel first-order filter function, should be 20 FILTCR | connected between Pins 20 and 21. 21 [e) VOR Right channel output. 22 - VREF Internal reference voltage for output channels (0.5V 00 typ.). 23 = VSSO. Operational amplifier ground. 24 = VDDO Operational amplifier supply voltage.
Block Diagram
CKSL1 CKSL2
Timine 421—syscik
DATA ws——2_| Seat 4fs DIGITAL UP-SAMPLE reales FILTER AND FEATURES APPL Bck 1 APPO MODE 171 app CONTROLS ppe sat APPS
testi 14 NOISE NOISE TEST2—— SHAPER SHAPER For Yeo
a1 sso LEFT OUTPUT RIGHT OUTPUT ‘SWITCHES SWITCHES
FILTCL [19 FILTCR
RCONV1 = RCONV2 1nF 3kQ — A cc cc ako Tn vou oP DIVIDER DIVIDER we cP 18 '\ s 21] VOR
Vaer [22
LI REFERENCE
a SOURCE 10 uF] Vssa | | 24 Wo 2 Vsso Vooo Vooa Vssa
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
{C28 OCTAL BUS TRANSCEIVER IC 74ACT245 SOP 300MIL Parts No. : 314-0649
Top View
P29} Voc ge fa] Bo {i7] Bt {16} 82 {15} B3 114] B4 {13] BS 112] Be {ri] B7
1C31/32 DRAM IC HM514260AJ-7 SOJ Parts No. : 315-0947-70
IC KM416C256BJ-7 SOJ SUMSUNG Parts No. : 315-0983-70
Wi Top View Wi Logical Operation Circuit
al8) 1:
- 3€N1 (Ba) OR SENZIAB) d @ 18) AO id Bo Bz ms a OT |_W7),, a2 4 | (16)g5 ag DH |_(15) 53 ag OH }_(14) B4 as O—| |_(3)p5 Ae ey |_(2) 56 | | ONp7
IC UPD424260LE-70-E2 SOJ NEC Parts No. : 315-0985-70
IC MB814260-70PJ-G SQJ FUJITSU Parts No. : 315-0984-70 @ Truth Value Table
INPUT | FUNCTION [QUTEUT G |DIR} ABUS | BBUS L | L JOUTPUT! INPUT | A=B L | H | INPUT |OUTPUT| B=A H |X High impedance Z
X: Don’t care Z: High impedance
IC TC514260BJ-70 SOJ TOSHIBA Parts No. : 315-0986-70
IC HY514260BJC-70 SOJ HYUNDAI Parts No. : 315-1030-70
iCss IC 74HC157 SOP Parts No. : 314-0634 Top View
1034
IC UPC78LO5T CHIP Parts No. : 313-5323 @ Description No. [Name Function [2 [8 [5 j8 jit |t0 1 | SEL | Common data select input 2 Al _| Data inputs from source 0 1 |A2 [B2 |A3 [BS 7 Ar B B 3_| BI _|Data inputs from source 1 sel 4 | Y1_| Multiplexer outputs SELECTOR 5 A2_| Data inputs from source 0 6 B2_| Data inputs from source | | | L I | l 7 Y2__| Multiplexer outputs 1516 g 8_| GND [Ground OV) MUTIPLEXER OUTPUTS 9 | Y3__| Multiplexer outputs 10 B3_| Data inputs from source | v3 vi__W2 L1_|_A3_| Data inputs from source 0
4 7 9 12 Y4_| Multiplexer outputs
- B4__| Data inputs from source 1 14 | A4_| Data inputs from source 0 15 G_| Enable input (active LOW) 16 _| Vec_| Positive supply voltage
IC TA78LO5F CHIP Parts No. : 313-5323-01
@ outeut
@ common i Top View @ Input Lars | acne) J Qt At th Katz ’ Q13 Qi = ORT Ro:
rar 3 |
ais aio
- OUTPUT -
- COMMON R10 R6 (SHIELD PLATE)
- INPUT Rit
1C35 IC S-80723AN-DL CHIP Parts No. : 313-5328
Bijop View
>.
- OUT
- VDD
- VSS
SH1 BOARD IC101 SHi CPU IC CUSTOM CHIP SH1 QFP Parts No. : 315-5785
Top View iC CUSTOM CHIP SH1A QFP Parts No. : 315-5785A
112 85
1 a ! i i
28 Fb
29 56 @ Description
No, vO Pin Name Function 1 IRQL. Host command interrupt input (level detection) 2 IRQH CD-ROM sync detection, subcode sync detection interrupt input (level detection) 3 VSS Ground 4 ADO 5 ADI 6 AD2 7 AD3 . 3 VO ADS Data input/output 9 ADS 10 AD6 oe AD7 12 = VSS Ground
- AD8 . 14 ie) ADS Data input/output 15 = VCC +5V 16 ADIO 17, ADIL 18 ADI2 « 19 1/0 ADI3 Data input/output 20 ADI4 21 ADIS 22 = VSS Ground 23 AO 24 Al 25 . A2 26 A3 37 fe} Ad Address output 28 AS 29 AG 30 AZ 31 = VSS Ground 32 Ag 33 Ag 34 Al0 35 All 36 fe} AID Address output 37 Al3 38 Al4 39 Als 40 = VSS Ground 41 Al6 42 fe} Al? Address output 43 a VCC +5V 44 Al8 45 Alg 46 fe) 20 Address output 47 A2l 48 [e) NC Not connected. 49 9) CASH DRAM CASH output
No. vO Pin Name Function 50 (o) CS2 CS2 output (GA, MPEG, other area 2 access) 51 {e) CASL DRAM CASL output 52 VSS Ground 53 1 TIOCAO, MPEG A data transfer (DMA3) request input (edge detection) 34 ) RAS DRAM CASL output 55 VO CS6 CS6 output (area 6 access) 56 = NC Not connected. 57 [e) WRL WRL output 38 (e) WRH WRH output 59 [e} RD RD output 60 fe} RESET GA reset output. Lo: RESET, Hi: Release 61 ~ VSS Ground 62 {s) NC Not conncted, 63 [e) TROOUT Spare (Spare to output "Lo” during interrupt process) 64 I TIOCAL MPEG V data transfer (DMA2) request input (edge detection) 65 [e) NC Not conncted.
- ie) DACKO DMAO (for CD-ROM sector data input) ACK output (to GA) 67 I DREOQO. DMAO (for CD-ROM sector data input) REQ input (from GA) 68 fe) DACK] DMAI (for host data input/output) ACK output (to GA) 69 i DREQL DMAI (for host data input/output) REQ output (from GA) 70 = vec +5V 71 ie) CK SH—I system clock output (20MHz) (to GA) 72 = VSS Ground 73 ] EXTAL. A crystal oscillator is connected. 74 I XTAL A crystal oscillator is connected. 75 = VCC +5V. 76 I NMI +5V 77 = VSS Ground 78 = NC Not conncted. 79 RESET Reset input (reset at "Lo”) 80 MDO 81 1 MDI MCU operation mode setting pins. The built-in ROM is effective. 82 MD2 83 - VCC +5V 84 - VCC +5V 85 = vec +5V (power supply of analog circuits) 86 = VREF +5V (analog reference power supply) 87 NC = - Ne Ground (not used) 90, NC 91 = AVSS Ground (analog ground) 92 = NC Ground (not used) VCD i: . 93 ! yep LEG dive omens He VCDconneced. 94 = NC Ground (not used)
- NC Ground 96 = VSS Ground 97 1 MPEGA IRQ. MPEG A interrupt input (edge detection) 98 1 EGV IRQ. MPEG V interrupt input (edge detection) 99 = VCC +5V 100 1 COMSYNC. CD communications start signal input. Lo: Start, Hi: In the middie ications sync interrupt input (edge detection). wo | TOMRED | CD gemmuntcatns syne erupt input Ce decon 102 = NC Not conncted. 103 = NC Not conncted. 104 [e) DEMP. Deemphasis output. Lo: DEMP OFF, Hi: DEMP ON 105 = NC No conncted. 106 = VSS Ground 107 1 CDATA CD communications data input (SCKO used) 108 {e) HDATA CD communications data output (SCKO used) 109 1 TEST Test control input. Lo: Test mode, Hi: Normal mode Ho {e) TDATA Test data output li [e) COMCLK CD communications clock output (SCKO used) 112 {e) TCLK Clock output for test data
SH1 BOARD iCiG2 DRAM IC HM514260AJ-8 SOJ IC HM514260AJ-7 SOJ Parts No. : 315-0947-80 Parts No. : 315-0947-70
i Top View & Pin Layout @ Pin Name Pin Name Function A0-A8 address input AO-A8 Refresh address input V/O1-1/04 Data input/output RAS Row address strobe
CAS Column address strobe WE Write enable OE Output enable Vee Power suppply (+5V)
Vsg Ground
Block Diagram RAS CAS WE OE
JRAS CONTROL CAS CONTROL WE CONTROL OE CONTROL CIRCUIT CIRCUIT CIRCUIT CIRCUIT
vo1 VO2 WO3 04
VO BUFFER VO BUFFER TL
o ied og Q c o z| & lz z| § jz zg g| & [eg a|e e| gig gq FE 2} 2 [2 Paes 2) = |= : Z| ask 18) & 1@ 2sek =| 2/2] 256k 2) © |B] _ 256k z a} MEMORY /2/ G |S] MEMORY |/o |/o | MEMORY |=} O | 5] MEMORY | ao 2] cen [2] 8 |@] ceu {S/F} cen |2) 8 {2} cer |Z w]} ARRAY ja | @ ja] ARRAY Jwlw| ARRAY ja] B ja} ARRAY [wi 2 = = gig = = g < <| Zfi< g < zZi< z 8 w} = jw aes w} 2 lw 8 wo = oO nT} no > oO nO z1 3 |é a| 8 \s Oo] Oo la a Co lo
WORD WORD WORD WORD [V|_ DRIVER DRIVER DRIVER DRIVER ROW ROW ROW ROW DECODER DECODER DECODER DECODER
ROW ADDERSS BUFFER COLUMN ADDRESS BUFFER
AO-AB
SH1 BOARD 10103 IC CUSTOM CHIP OCU YGRO19A Parts No. : 315-5873
Top View
FP 126
i i i i i ! Eb as
Block Diagram CD SIGNAL ‘SH uP (- ) PROCESSOR DESCRAMBLE b+ SUBEODE CD-ROM Date / a) wes Ga] | pee Een iRa2 % 7 poowrany| Paeete HDs9232 ADR DATA COIROMSK oper) seats ‘SUBCODE
16 8
7 C va Date BU ~ b S| MPEG Part: t u J Audio co}
FO | Ow | [coronsk [CDI ROREO| COMMAND. H 8 ise (Loner) REG. 0-3 sz See SUBTRACT! | Px. é MPEG ge |g RESPONSE aT cy "| Video 22 168 REG. 0-3 : -Bus FIFO] Fo 188 © 125 COUNTER )
- ‘bus DATA ] SH DATA BUS 1 red UB) i if if J eesye) | at Lt x 25 {I IRQ 16 AUDI ci AGB
HOST SYSTEM D)
# Description No. vo Name ‘Function 1 1 MVPRT Video transparency control signal 2 MVR7 3 MVR6 4 i MVRS5 Video red color data 5 MVR4 6 MYR3 7 - vcc Power supply 8 = VSS Ground 9 MVG7 10 MVG6 ll 1 MVGS Video green color data 12 MVG4 13 MVG3 44 I MVB7 Video blue color data 15 = VSS Ground 16 MVB6 = 1 _— Video blue color data 19 MVB3 20 AAI 21 1 AA2 A-BUS address bus 22 AA3 23 = VSS Ground 24 AA4 = 1 oe A-BUS address bus 27 AAI8 28 I ACS2 Chip select signal from A-BUS 29 I WTRS Wait control signal used to transfer MPEG video frame data 30 = VSS Ground 31 [e} FDACK MPEG video frame data transfer control signal 32 le} MVCS MPEG video chip select signal 33 oO MACS MPEG audio chip select signal 34 fe) TPS Test pin 35 = VCC Power supply 36 = VSS Ground 37 I RESET Gate array system reset signal 38 I MABICK Sync clock used to transfer MPEG audio serial data 39 I MASDATAI MPEG audio serial data signal 40 i MALRCLK Clock used to detect MPEG audio serial data L/R 41 I TP2 Test pin 42 I SCS6 SH chip select 6 43 - vss Ground 44 SDLO 45 SDLI 46 1 SDL2 SH uP subdata bus 47 SDL3 48 SDLA 49 = vec Power supply 50 = vss Ground 51 SDLS 52 SDL6 2 I an SH uP subdata bus 55 SDL9 56 SDL10
No. vo Name Function 57 = VSS Ground 58 SDLI1 59 SDL12 60 1 SDL13 SH uP subdata bus 61 SDL14 62 SDLIS 63 - VCC Power supply 64 = VSS Ground 65 SA21 66 SA20 67 I SA4 ‘SH uP address bus 68 SA3 69 SA2 70 I SRD SH uP read enable signal 71 - VSS Ground 72 1 SHCK 20MHz clock 73 i SAI SH uP address bus 74 I IRQOUT SH uP interrupt factor generation signal 75 I SCS2 SH uP chip select 2 76 I DACK1 Channel 1 DMA transfer response I - vec 78 = VSS Ground 79 I DACKO Channel 0 DMA transfer response = i a DRAM control signal 82 I SWRH SH uP upper byte write enable signal 83 I SWRL SH uP lower byte write enable signal 84 1 SA19 SH uP address bus 85 1 TP3 Test pin 86 - vss Ground 87 io) DSWR Delayed write cycle control signal 88 fe} DREQI Channel 1 DMA transfer request 89 fe} DREQO Channel 0 DMA transfer request 90 I SDH15 SH uP main data bus 91 = VCC Power supply 92 = VSS Ground 93 SDH14 94 SDH13 95 I SDH12 ‘SH uP main data bus 96 SDH11 97 SDHI10 98 - VSS Ground 99 SDH9 Power supply 100 SDH8 mu] SDH? uP main dats 103 SDHS 104 - VCC Power supply 105 - VSS Ground 106 SDH4 107 SDH3 108 I SDH2 SH uP main data bus 109 SDH1 110 SDHO il [e} SIRQH SH uP upper byte (CD-ROM) interrupt signal 112 = VSS Ground
No. vO Name Functfon 113 0 SIRQL SH uP lower byte (A-BUS) interrupt signal 114 fe) BCK Audio serial data sync clock 11S oO LRCK Audio L/R channel switching signal 116 - VCC Power supply 7, 0 sD | Audio serial data 118 Oo SUBCK | Subcode input clock 119 = VCC Power supply 120 = VSS Ground 121 I CFCKO Frame sync signal 122 ij SUBOUT CD subcode data 123 1 Sl Subcode block sync signal 124 I DAS CD-DA audio serial data 125 1 CKX CD audio seria! data sync clock = 4 a CD audio L/R channel switching signal 128 1 C2F C2 error flag 129 1 SMPX CD-ROM data byte sync signal 130 if SDAS CD-ROM serial data 131 I SCKX CD-ROM serial data bit sync signal 132 = VSS Ground 133 = VCC Power supply 134 = VSS Ground = I ame. A-BUS timing control signal 137 I ARD A-BUS read signal 138 = VSS Ground 139 I AFCO. A-BUS timing control signal 140 1 AWRO ‘A-BUS lower byte write signal 141 I AWRI A-BUS upper byte write signal 142 i AFC1 A-BUS timing control signal 143 = VSS Ground 144 oO AWAIT A-BUS wait control signal 145 oO AIRQ A-BUS interrupt signal 146 - T Test signal for scan pass te I = A-BUS data bus 149 = VCC Power supply 150 - VSS Ground 151 AD2 = I ~ A-BUS data bus 154 ADS 155 - VSS Ground 156 AD6 187 AD7 158 I AD8 A-BUS data bus 159 AD9 160 AD10 161 = VCC Power supply 162 = VSS Ground 163 ADI 164 ADI2 165 I AD13 A-BUS data bus 166 ADI14 167 ADIS 168 - VSS Ground
- EXPLODED VIEW & PARTS LIST
- 11-1. Exploded View
11-2. Mechanical Parts List
Ref. No. Parts No. Description No. Parts No. Description
1 610-5862 ASSY TOP CASE SATURN EUR isp 54 601-7815 STAELE PROTECTION SHEET SAT 1 610-5927 ASSY TOP CASE SATURN AUS [2]
1-1 | 610-5864 ASSY LID CD SATURN EUR 1-2 | 253-7015 TOP CASE SATURN EUR 1-3 | 253-7013 LID _CRTG SATURN USA 1-4 | 253-6917-03 BUTTON OPEN SATURN USA 1-5 | 253-6919-03 BUTTON RESET SATURN USA 1-6 | 253-6920 BUTTON OPEN LEVER SATURN JPN 1-7 | 253-7012 MOUNT POWER UNIT PCB SAT USA 1-8 | 253-7010 PANEL DEC. FRONT SATURN USA 1-11 | 601-7774 OIL DUMPER SATURN 1-12. | 250-5404 BRACKET LEVER SATURN JPN 1-13 | 250-5423 BRACKET LID CD SPRING SAT USA 1-14 | 250-5424A BRACKET LID CD HOLDER SAT USA A 1-17 | 125-5125 SPRING LID CD SATURN JPN 1-18 | 125-5126 SPRING LID CRTG SATURN JPN 1-19 | 125-5127 SPRING ARM SATURN JPN 1-20 | 510-5068 DETECTOR SW SPPBI1 1-21 | 600-6536 WIRE HARN 2P FOR DETECTOR USA 1-22 | 601-7726 PLATE SEVER SMALL SATURN JPN 2 610-5863 ASSY BOTTOM CASE SATURN USA 2-1 253-7016 BOTTOM CASE SATURN EUR 2-2 | 601-7658 RUBBER FOOT SATURN JPN 3 837-11492 ASSY IC BD SATURN VAQ PAL 5 838-10834 1C BD SATURN SHT 6 610-5679-20 ASSY CD DRIVE UNIT SATURN 6 610-5679-21
7 400-5271 AC POWER UNIT SATURN EUR 7 400-5272 AC POWER UNIT SATURN EUR
Al-1 | 601-7672 INLET FOR UL/CSA SATURN AT-2 | §14-5066 FUSE 1. 6A 080026 10 253-6915-03
n 253-6918-03 n 253-6918A-03
12 253-6921 253-6932 5 169 15 601-7979 16 600-6416
7 600-6560
18 600-6431 18 600-6431 -01
2 270-5094 2 270-5095
38 250-5417 39 253-6922 40 029-000034 4 029-000034-0B 42 029-000035
43 029-000035-08 44 029-000036 45 029-000049 46 023-000061 4l 029-000063
48 029-000049 49 029-000049-08 50 029-000052 5 029-000067-0B 52 029-000064
53 401-0054 LID BATTERY SATURN EUR
BUTTON POWER SATURN USA BUTTON POWER SATURN USA A
MOUNT MECHA SATURN JPN SLIDE RAIL SATURN JPN POWER SW SDDLD PLATE SEVER LARGE SATURN USA WIRE HARN SP FOR ST CD
WIRE HARN 2P FOR P. SY NEW
FFC 20P L=180MM FFC 20P L=180MM
FERRITE CORE BP53RB120070060M FERRITE CORE L6 112. 5X5. 5X7
BRACKET 9P CONN HOLDER BAT HOLDER SATURN MATSUSHITA B-TITE SCR PH 3X8 B-TITE SCR PH BLK 3x8 B-TITE SCR PH 3X10
B-TITE SCR PH BLK 3x10 B-TITE SCR PH 3X12 B-TITE SCR BRH 2. 6X8 B-TITE SCR PH 3X14 S-TITE SCR BI H2X4
B-TITE SCR BRH 2. 6X8 B-TITE SCR BRH BLK 2. 6X8 B-TITE SCR PH 2x8 B-TITE SCR BRH BLK 2. 6X6 S-TITE SCR PH 2X8
BATTERY CR2032/1F
{Note] [1]----EUR [2] +7 AUSTRALIA
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
©1995 Sega Enterprises, Ltd. Printed in Japan (I) 50630