CATHODE RAY TOMES

Dunkmania

Dunk Mania (World, DM2/VER.C) (Namco, 1995) · Document · 4 pages · 7 sections · original scan

Page 1

Nnamco

DUNKMANIA

OPERATION MANUAL

A\ CAUTION In order to safely use this machine, be sur e to car efull y r ead this oper ation manual and the manual of the cabinet in which this machine to be instal! ed befor e installation and oper ation.

DISTRIBUTED BY: NAMCO LIMITED 2-8-5 TAMAGAWA, OHTA-KU, TOKYO, 146, JAPAN

©1995 NAMCOLTD., ALL RIGHTS RESERVED

Page 2
  • Cautions
  • Be sure to turn off the cabinet whenever installing or removing the PC board. Otherwise you may be hurt by an electric shock.
  • Be sure to use an edge connector which is applied to the JAMMA standard. Any modifications such as cutting the edges of PC boards will cause a failure and also will be out of our guarantee for repair.
  • Never test the PC boards for conductivity with a multimeter or similar device. The PCB contains sensitive chips which could be destroyed even by the internal voltage of such a device.
  • Foreign matters or dust on the PC boards will cause a failure. Tum off the power and clean the PC boards with a brush or similar thing.
  • When transporting the PC boards, wrap them with sponges or air caps and pack them in a card board box so that they can avoid a direct impact from outside during shipment.
  • For maintenance, contact your distributor.
2. Specifications1P,Start2P,Start3P,Start4P Start
(1) Control panel:One-side 4-P specifications1p, g-direction2P, 8-direction3p, 8-direction | 4P, 8-direction

+ 8-direction lever: 4(1P, 2P, 3P,4P, 1 each) + Button switch: 12( IP, 2P, 3P,4P, 3 each) ae:

Button 1 : (Shift)So=“Oond

Button 2 : (Shot& Block)

Button 3 : (Pass&Steal)1a ap)aoMs @
+ Start switch:4(1P, 2P, 3P,4P, 1 each),ALYIN AKKAA
(2) PC board size:230 x. 230 mmLE-Butontf2P, Button 1\3P, Button t4P, Button “|

. 1P, Button 2 2P, Button 2 3P, Button 2 4P, Buiton 2 a , : IP, Button 3

  • Direction of monitor: Horizontal en
2P, Button 33P, Button 34P, Button 3

Fig. 1

3.Connection

  • Connection of control panel See above to connect JAMMA hamess and extended hamess(accessory) to control panel through the cabinet (see P3 : PC board connector table) Connecting expanded harness to the right speaker allows you to enjoy a stereophonic effect.
  • Connection of PC board Set the PC board in the cabinet and connect JAMMA edge connector and 48P extended edge connector (DDK 225D-10024C2-2312) to the PC board. 48P extended edge S6P edge connector
4. Explanation of PC Boardsconnector(JAMMA)
  • Option switches No.1 to "ON" for Test Mode. No.2 to "ON" for Screen Freeze. Normally, all of the option switches are "OFF". Speaker volume
  • Speaker volumes To decrease the sound volume of the speaker, turn the speaker volume counterclockwise.
  • Test Mode
  • The PC Board enters the test mode by setting the test switch on the PC Board to "ON" on the game screen. And the test menu screen is displayed on the monitor. Use the test switch (For connection, see P3: PC Board Connector Table) on the cabinet or the option switch on the PC Board. (see P1: 4.(1) Option switches) When an item is selected by operating the IP control lever up and down and the IP button! switch is pushed, the selected test screen is displayed.
  • Game fees can be changed on the coin option screen, and the game difficulty can be changed on the game option screen Select an item by operating the 1P control lever up and down, and change its contents using the IP button! switch (see the option setting table). After that, push the 1P button2 switch to return to the test menu screen.
Page 3

SWITCH TEST }— (a) Switch test screen SOUND TEST: t~ (b) Sound test screen COIN OPTIONS + (c) Coin option screen (Setting of game fees) GAME OPTIONS +--(d) Game option screen (Setting of game difficulty) UARTS TEST ———— (e) Not used POLYGON TEST 1—(f) Polygon test screen ADS. +— (g)Not used COLOR TEST t— (h) Color test screen (for monitor adjustment) CONVERGENCE TSTE +— (i) Cross hatch pattern (for monitor adjustment) RS-232C TEST. (j) Not used (Test menu screen)

CO IN OPTIONS GAME OPT IONS, [DEFAULTS IN GREEN ] IDEFAULTS IN GREEN }

GAME COST : (1 or 3) COIN 1 CRED IT.}—1DIFFICULTY LEVEL : MIDIUMj—

DISCOUNT TO CONT INUE : NO———_—_———_+—2 ROUND TIM : 2 MIINUTES—————_}—— | CO IN | MECH VALUE : 1 COIN COUNT AS 1 COIN—+-——3, CABINET TYPE : 4 PLAYERS}!

CO IN 2 MECH VALUE : 1 COIN COUNT AS 1 COIN—+——4MUSIC IN ATTRACT : YES—!

COIN 3 MECH VALUE : 1 COIN COUNT AS 1 COIN—+——5 SPEAKER OUT = STEREO———————_}>—— CO IN 4 MECH VALUE : | COIN COUNT AS 1 COIN—+——6 UNIFORM COLOR : Usa} BONUS FOR QUANTITY BUY IN: NONE———————}——7 CRED IT MODE : COMMON — COIN COUNTER : TYPE A : 1 COUNTER- t——-9 FREE PLAY: NO 10

(Coin Option screen) (Game Option Screen)

(Option setting table) Item —_—W24 do OT Contents

1. Game feesone count required for one ame (one credit) | (1 or 3)<f1- 91
2. DISCOUNT50% discount when continuina a plavNO < YES

3.COIN1 MECH VALUE _| Count per coin 1<-9

  • COIN2 MECH VALUE __| Count per coin 1<f1-91
  • COIN 3 MECH VALUE __| Count per coin 1<-M
6. COIN 4 MECH VALUECount per coin__ji<t-91
  • BONUS COIN betneaienaial coin per the specified number | NONE < Scan ae oe COMMON (Credit is common to 1P, 2P,3P and 4P) <,
  • CREDIT MODE EACH ONE (Credit is set for 1P, 2P,3P and 4P each) EACH TWO (Credit is set for 1P and 2P,3P and 4P each)
  • COIN COUNTER a TYPE A:1COUNTER < TYPE B :2COUNTERS
10. FREE PLAYNO<_ YES7-
  • DIFFICULTY LEVEL __| MEDIUM <[ EASY. MEDIUM . HARD 1 ee
12. ROUND TIME2MINUTES < [1. 2.3.4.5]|
13.CABINETTYPE4 PLAYERS <_2PLAYERS

14,.MUSIC IN ATTRACT YES <_ NO

15.SPEAKER OUTSTEREO < MONOee_
16.UNIFORMCOLORUSA<JAPAN|
“|Game fees..el| Credit(Note) |]
Example1E@me_{Contines:_neyona Mech 20
| 100 yen | 100 yen1 COIN 1CREDIT | NO1COUNT 1COINNONE | CREDITO| use.

[100 yen | “50 yen | 2 COINS ICREDIT “ [ves | 1CouNT 2coINs [NONE | CREDIT 0/2 Dusen

Page 4
  • PC Board Connector Table

JAMMA edge connector (S6P 3.96 mm pitch) Solder side Terminal No. Parts side

GND A 1 GND

GND B 2 GND

+5.Cc3+5V
+5.D4+5V

E 5

+12VF6+12V
Insertion errorH7Insertion error

preventing preventing

Coin counter 28Coin counter 1

9 _|Coin lockout 1 J K

Speaker (-)L10| Speaker (+)
Audio (GND)M11[Audio +)
Video GREENN12|Video RED
Video SYNCP13|Video BLUE
Service switchR14 | Video GND
Ss15__|Test switch
Coin switch 2T16[Coin switch 1
2P start switchU17__|1Pstart swich
2P lever UPVv18|1Plever UP
2P lever DOWNWw19_|1P lever DOWN
2P lever LEFTx20|1P lever LEFT
2P lever RIGHTY211P lever RIGHT
2P button!Zz221P button!
2P button2a23{IP button2
2P button3b24{IP button3

€ 23 d 26

GND e 27 GND GND f 28 GND

+ Do not connect anything to the blank connectors. + Both lockout solenoid and coin counter operate on +12V. + Connect the switches to N.O. terminals such as a microswitch, and the GND to the COM terminal.

N.O. COM NC.

+ The supply voltage is available within +5%. For use in the best condition, get the supply voltage as close to the specified voltage as possible.

(Recommended power capacity)

+5V 5% 2.5A or more +12V 45% 2.0A or more Extended edge connector (48P 2.54 mm pitch) Solder side Terminal No. Parts side

Speaker R(-) [YEL] | ALBI[Speaker R (+) [ORG |

A? Bz _

4P start switchAgBS

Ad BS _ Insertion error | AS | BS | Insertion error preventing key preventing key

4P lever RIGHTA6Be|4P lever LEFT
4P lever DOWNATB7__[4P lever UP.
4P button!ARB8[4P button?
a9Bo|GND.

aw | Bio [GND au | Bu a2 | Biz Als | BIS |4P button ala | Bia

Coin switch 4AIS | BIS{Coin switch 3

al6 | BI6 ai? | B17 |GND ais | BI8 [GND

3P_button3AloB19|3P button2
3P button!20 | B20[3P lever RIGHT
3P lever LEFTAllB21|3P lever DOWN
3P lever UP.A22B22|3P start switch

a2 | B23 Az | B24

+ Do not connect anything to the blank connectors. + The colors indicated in [] in the extended edge connector table show these of color cords on the extended edge connector hamess in the accessories.

{Connection to stereo cabinet] (I)STEREO / MONO setting Select SPEAKER OUT in the game option screen at the test menu screen.

<Caution>Monophonic cabinets do output only the left-hand sound even if the stereophonic setting is selected.

  • Connection to speakers + Connect the (L) speaker to the speaker output of 56P edge connector (AMMA) on the PC board. + Connect the (R) speaker to Speaker R (+), (-) of 48P extended edge connector.
  • Use a DDK 225D-10024C2-2312 as a 48P extended edge connector.