Outrun 2 Std
OutRun 2 (Rev A) (GDX-0004A) (Sega, 2003) · Manual · 86 pages · 42 sections · original scan
1ST PRINTING JUNE ‘04 www.sauservice.com
SEGA
SEGA PRESENTS
Standard Version
Owner’s Manual
SEGA AMUSEMENTS USA, INC. MANUALNO. 999-2102 GAME CODE: ORT
eee @ SegaService.com
VISIT OUR WEBSITE!
sayoneg | é
\ A10rstH
qoueas
yoogdens
Jep|oH aed @ e ft ® & @ Back nward Stop _Refresh Home = AutoFill Print Mail Dio
@© macosx © wicrosoht MacToia @ Segaserice.com © SAU Parts ste @) MacOS xHints-Get the most from x! @ Microsoft Outlook Web Access - Logon
~
LEDs "Burnine! SERVICE
"Bulletins "Dari's Office
- Game Manuals "Seearen “What's New
If you have any questions or comments about this site please E-Mail to Darl.Davidson@seu.sega.com
[what's new] [manuals] [bulletins] [assemblies] [specials] [Search] [staff] [Dan's office] [Return/Parts Policy] [warranty] [corporate info] [plugins] [Non-framed page]
You will need the following items to view this page in its entirety.
All Platforms Windows — Macintosh
[Sega Amusements USA 45133 Industeial Dr Fromoat,CA 94538 (415) 701-6580
@ internet zone y
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOW To maintain the safety:
To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.
Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.
Indicates that mishandling the prod- Indicates that mishandling the product uct by disregarding this warning by disregarding this caution will cause will cause a potentially hazardous a slight hazardous situation which can
For the safe usage of the product, the following pictographs are used:
this display is attached to places where the Owner’s Manual and or Service Manual should
( Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment,
be referred to.
© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.
© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.
© Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.
© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.
© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.
© _ Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. © Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. fe) When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.
Descriptions herein contained may be subject to improvement changes without notice. The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?
TABLE OF CONTENTS
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL
- HANDLING PRECAUTIONS ....
- PRECAUTIONS CONCERNING INSTALLATION LOCATION
- OPERATION ....
- NAME OF PARTS.
- ACCESSORIES ...
- ASSEMBLING AND INSTALLATION ...
- PRECAUTIONS WHEN MOVING THE MACHINE
- GAME DESCRIPTION .
- GAME TEST MODE .
- EXPLANATION OF TEST AND DATA DISPLAY
- HANDLE MECHANISM
- SHIFT LEVER
- ACCEL & BRAKES(S) ..
- COIN SELECTOR
- MONITOR ....
- PERIODIC INSPECTION TABLE .
- GAME BOARD ...
- NETWORK PLAY
- DESIGN RELATED PARTS
- PARTS LIST
- WIRE COLOR CODE TABLE
- WIRING DIAGRAMS ... S 1-2
3-4
5-8
10-12
13-22
24-33
34-40
41-42
43-45 46 - 47 48 - 49 50-52
53-54
55-56
57-63 64 - 66
68 - 75
XXX
SPECIFICATIONS Installation Space : 75.5 inches wide X 38.75 inches deep Height : 70 inches Width : 30.25 inches Length : 67.5 inches Weight : ~680 Ibs Power, maximum current : 540 W 4.5 A(AC 120V 60 Hz AREA)
MONITOR : 29 inch supplied by Sanwa Monitor: 998-0612 Chassis: 998-0161
INTRODUCTION OF THE OWNERS MANUAL
This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, OUTRUN 2 STANDARD TYPE. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, non-technical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.
Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.
Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.
SEGA AMUSEMENTS USA, INC. / CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594
DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN
Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's main-
Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.
The location's maintenance man and serviceman are herein defined as follows:
"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.
Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.
Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.
Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.
LISTED
5K92 ®
AMUSEMENT MACHINE
Notes:
- HANDLING PRECAUTIONS
A\
WARNING!
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.
Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit. To avoid causing a fire or electric shock, do not put things on or damage Power Cords. When or after installing the product, do not unnecessarily pull the power cord. If damaged, the power cord can cause a fire or electric shock. In case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted. Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.
(10?) For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard.
@ PRODUCTION DATE @
This SEGA product was produced in the year of:
2004
This signifies that this work was disclosed in 2004.
- PRECAUTIONS CONCERNING INSTALLATION LOCATION
A\
WARNING!
This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, injury and or malfunctioning.
P
P the proximity of an indoor swimming pool and or shower, etc.
proximity of heating units, etc.
chemicals or hazardous matter. aces subject to rain or water leakage, or places subject to high humidity in
aces subject to direct sunlight, or places subject to high temperatures in the
aces filled with inflammable gas or vicinity of highly inflammable/volatile
lusty places. oped surfaces. aces subject to any type of violent impact. icinity of anti-disaster facilities such as fire exits and fire extinguishers. e operating (ambient) temperature range is from 5°C to 30°C.
LIMITATIONS OF USAGE REQUIREMENTS
A\
Bi E age and frequency requirements. A plate describing Electrical Specifications is attached to the product. Non-compliance with the Electrical Specifications can cause a fire and electric shock. T tion facilities. Using them in a manner not independent can cause a fire and electric shock. E (AC single phase 100 ~ 120 V area). Non-compliance with the Electrical Specifications can cause a fire and electric shock. B age Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Pi fire resulting from overload. When using an extension cord, ensure that the cord is rated at 10 A or higher (AC 100 ~ 120 V area). Using a cord rated lower than the specified rating can cause a fire and electric shock. e sure to check the Electrical Specifications. nsure that this product is compatible with the location's power supply, volt-
his product requires the Breaker and Earth Mechanisms as part of the loca-
nsure that the indoor wiring for the power supply is rated at 10 A or higher
e sure to independently use the power supply equipped with the Earth Leak-
utting many loads on one electrical outlet can cause generation of heat and a
Operation Area
nN For the operation of this machine, secure a minimum area of 38.75 in. (W)
- x 75.5 in. (D). In order to prevent injury resulting from the falling down
(0?) For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 32.75 in. (W) and
-— Electric current consumption — 275 75 in.
MAX. 4.5 A (AC 120 V 60 Hz)
j Fi
4 in. over
FIG. 2
- OPERATION
PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION
A\
WARNING!
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.
In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.
** Note: Image differs from actual product.
Ensure that all of the SUPPORT BRACKET are in contact with the floor.
Ensure that all of the Adjusters are in contact with the floor.
product can cause a falling down accident or parts damage.
mn Do not put any heavy item on this product. Placing any heavy item on the
tially crowded situation at the installation location. Insufficient installation
PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.
J To avoid injury and accidents, those who fall under the following categories
. - are not allowed to play the game.
A\
WARNING!
A
CAUTION
@ To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.
This product is intended for 1 Player only per seat. Playing the game by 2 or more Players riding on the seat together can cause falling down and collision accidents by striking head, hand, or elbow.
@Caution the player so as not to hold a child in her/his lap to play. Failure to observe this may cause the child to be caught between the Control Panel and the player and fall down. ** Note: Image differs from actual product.
** Note: Image differs from actual product.
Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down. Instruct the Player to adjust the seat before playing the game. Playing the game in a forcible posture can cause a contingent accident.
www. 2uservice.com
PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION (CARD SYSTEM)
(10?) When an unjust act is performed, no written data is backed up mechanically. The following acts may be judged to be unjust acts.
If the card reader/writer has not been set as being unused, you will be unable to select any game mode with use of cards while the game will be in progress. Thus, for the card reader/writer, deal with the player, paying attention to the following points:
Even if the player requests the system for use of cards when you have set the machine so that the card reader/writer is not used, the request is rejected.
RNING: HAZARD TO EPILEPTICS. A very small portion of the population has a condition which may cause them
- NAME OF PARTS
29” Monitor
Shift Lever
Coin and Cashbox Door
Accelerator & Brake
Main Base
TABLE 4 Dimensions and Weights
Width x Length x Height 30in x 67.5in x 70in Weight ~680 LBS
- ACCESSORIES
When transporting the machine, make sure that the following parts are supplied. Magnetic cards for the recording of play results, and cleaning kits for cleaning the head of the card reader/writer are sold separately. Subsequent purchases of these items can be made by contacting the office listed on this Owner's Manual or the dealer from whom the product was originally purchased. Be sure to provide the part number(s), name(s), and required number of items.
TABLE 5 a ACCESSORIES
KEY MASTER KEY DESCRIPTION OWNER'S MANUAL 9301A (2) (2) Part No. (Qty.) 999-2102 For the CASHBOX DOOR For opening/closing Notes the doors Figures Parts not labeled with part numbers are as yet The Keys are inside the Coin unregistered or cannot be registered. Be sure to Chute Door at the time of shiphandle all parts with care, as some parts are not ment from the factory. available for purchase separately.
TAMPERPROOF WRENCH 3/16 TMP SCR (1) T-27 Torx 1/4-20 (1) T-15 Torx 8/32 (1) T-10 Torx 6/32 (1) Tool
The following Table 5b lists the parts that are separately marketed but are necessary when booting this product's software. When having unpacked the shipping crate, make sure that all the parts in this Table 5b are in the crate. If not so, contact where you have obtained the product.
TABLE 5 b (XKT-0833 : GD-ROM DRIVE KIT)
GD-ROM DRIVE XKT-0833 Device that loads the software in a GD-ROM disc. see 5 of Section 6.
TABLE 5 c
GD ROM KIT ORT
CUSHION SPONGE 601-11137 (1) GD-ROM Disc Protector
KEY CHIP (1)
CHIHIRO GDROM ORT ENG a)
This carton box is a standard accessory of the GD-ROM drive.
HOW TO USE THE CARTON BOX (GD-ROM DRIVE)
When you want to order for replacing or repairing service of the GD-ROM drive that is used by the product, pack it in a carton box as instructed below, 1 and then deliver the carton box to a service agent. If you do not observe the
- ASSEMBLING AND INSTALLATION
Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard.
Handle molded parts with care. Undue weight or pressure may cause them to break and the broken pieces may cause injury.
When carrying out the assembling and installation, follow the following 4-item sequence. 1 | SECURING IN PLACE(ADJUSTER ADJUSTMENT) 2 | INSTALLING THE GD-ROM DRIVE(SETTING GD-ROM DISC) 3 | POWER SUPPLY, AND EARTH CONNECTION 4 | TURNING POWER ON
Tools such as a Phillips type screwdriver, wrench, socket wrench and Ratchet Handle are required for the assembly work.
P eee KO) WRENCH SOCKET WRENCH.RATCHET HANDLE ——r T] Phillips type screwdriver
1 SECURING IN PLACE (ADJUSTER ADJUSTMENT)
AN Make sure that all of the adjusters are in contact with the floor. If they are not, the WARY! cabinet can move and cause an accident.
This product has 8 casters and 8 Adjusters. (FIG. 6. 2 a) When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5 mm from the floor and make sure that the machine position is level.
@ Transport the product to the ADJUSTER installation position.
@ Have all of the Adjusters make contact with the floor. Adjust the Adjuster's height by using a wrench so that the machine position is kept level.
@ After making adjustment, fasten the Adjuster Nut upward and secure the height of Adjuster. CASTER
FIG. 6. 2a BOTTOM VIEW
- Note:Picture may differ from actual unit.
ADJUSTER
Sea;
FASTEN UPWARD. _ oO ~s a y Sg \ apruster t
FIG. 6. 2b ADJUSTER Approx. 5mm
38.75 in.
“ul g ‘xoidde yuo,
4 in. over
FIG. 6.2¢ Provide ventilation space for the ventilation opening. Allow more than 28 in. of space for customer traffic.
INSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)
Carefully handle the GD-ROM drive so as not to contaminate the disc and the readout lens with stains and dust particles. Do not continue to use the scratched GD-ROM disc. The scratched GD-ROM
@ Unpack the shipping crate, and take out the GD-ROM drive, GD-ROM drive bracket, and GD- ROM disc.
GD DRIVE BRACKET GD-ROM DRIVE
PHOTO 6. 3a
@ Use the 4 tapping screws to fix the GD-ROM drive bracket onto the GD-ROM drive. Be careful about a fixing direction.
TAPPING SCREW (4) Max8
GD DRIVE BRACKET
FIG. 6.3 b
@ Remove the | truss head screw that fixes the GD-ROM drive lid (DISC LID). And turn clockwise the lid to remove.
TRUSS SCREW (1)
PHOTO 6.3b
@ Set the GD-ROM disc onto the GD-ROM drive with its labeled side facing upward.
@ Return the lid to its original place, and fix it with 1 truss head screw. Be careful not to fasten the screw too tightly.
PHOTO 6. 3c [TRUSS SCREW (1)
@ Undo the lock on the side of the unit base and remove the Truss screws.
@ Turn the knob to open the lock, and lower the seat towards the backrest. Slowly lower the backrest until it touches the floor to prevent damage to the seat components. Put a drop cloth on the floor to prevent damaging the surface of the seat components.
DROP CLOTH TO PREVENT DAMAGE TO SURFACE OF PARTS.
TRUSS SCREW (2), black
- Note Figure may appear different then actual product. FIG. 6.3 b
@ Attach the GD-ROM drive with 3 screws.
SCREW (3) M4x16,
PHOTO 6. 3d
@ Connect the GD cable connector (for data communication) to the DIMM board.
GD CABLE CONNECTOR
PHOTO 6.3 e
@ Insert both the GD cable connector (for data communication) and the power cord connector into the GD-ROM drive. Be careful about an inserting direction in this instance. Make sure that the connectors are inserted firmly and completely. Secure the cable with the cord clamp.
GD-ROM DRIVE __~s.8)
Power Cord connector
Secure the cable.
PHOTO 6.3 f
Attach the accessory stickers to both the Game Board and the Media Board.
KEY CHIP
MEDIA BOARD
PROJECTION
FIG. 6.5¢
Return the ASSY MAIN BD (now installed with the GD-ROM drive) into the PTV cabinet. Following the above-described actions in a reverse order, fix the base, connect the connectors, and clamp the wires/cables.
POWER SUPPLY, AND EARTH CONNECTION
A\
WARNING!
Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.
The AC Unit is located on one side of Cabinet. The AC Unit has Main SW, Earth Terminal and the Inlet which connects the Power Cord.
@ Ensure that the Main SW is OFF. -— ———
\ Q
Main SW off MAIN SW | i
| INLET
fe) fe)
FIG. 6.4.a AC unit
- Note: Actual Power Supply connection may vary from photo
AC Cable (Power Cord)
4 TURNING POWER ON
Turn on the AC unit's main switch to supply power to the unit. Once power is turned on, the fluorescent lamp lights up. The Start System Screen displays after a lapse of several seconds. It is followed by the screen that indicates that the network is currently being checked if the communication mode has been set. If there is a bad or improper communication connection, each screen will not proceed to the next, remaining on the currently Network Check Screen. If this occurs, resolve the error according to the instructions in this document.
If the communication mode has not been set or the communication check ends normally, the Motor Check Screen returns. While the Motor Check Screen is on-screen, the steering wheel can move either clockwise or counterclockwise. If you touch the wheel, the motor check is hindered and the game will not operate normally. So, you must not touch it at this time. Failures are displayed, if found. Resolve the errors according to the instructions in this document.
Once all the above steps have been completed, the Advertise Screen displays and voices are output through the left and right loudspeakers, unless you have set the machine so that no voices are output during the Advertise mode.
This product retains the number of credits and the ranking data even after the power is turned off. It does not retain data about the fractional number of coins (i.e., the number of coins not reaching one credit) or the bonus adder count.
Fluorescent lamps are always lit.
On-screen images are outputted.
- Note: Picture may differ from actual unit.
FIG. 6.5
- PRECAUTIONS WHEN MOVING THE MACHINE
nN @ When moving the machine, be sure to unplug the power plug. Moving the
—— machine with the plug as is inserted can damage the power cord and cause fire
man Do not push on any parts made of glass (e.g. CRT screen) or plastic, as these parts may break and result in bodily injury.
CAUTION!
** Note: Image differs from actual product.
Do not push the cabinet from the left/right direction.
- Game Description
Basic Controls
Insert a coin and press the Start Button to begin a game. Choose your car, background music, and other options. View choices with the Steering Wheel, and enter you selection with the Gas pedal.
During game play, use the Gas pedal to accelerate your car, and the Brake pedal to stop. The Gear Shifter can be used to shift up and shift down when using Manual Transmission.
You can switch between three different view settings with the View Change Button.
Game Outline
This is a driving game. The player controls a car (Ferrari), listening to great music and enjoying roadside scenery in the company of a gorgeous female passenger, all while racing towards the goal before time is up. The time limit is extended at each checkpoint. The game ends when the player runs out of time or reaches the goal,
Each game stage ends with a fork in the road where the player must decide the route using the car during the race. There are a total of fifteen stages, and five separate goal areas.
The three single player game modes are OutRun Mode, HeartAttack Mode, and Time Attack Mode.
The games’ Versus Mode accommodates play for up to four players.
SA: Tulip Garden 4A: Cloudy Highland 3A: Castle Wall 5B: Metropolis 2A: Deep Lake 4B: Industrial Complex 1A: Palm Beach 3B: Coniferous Forest 5C: Ancient Ruins 2B: Alpine 4C: Snow Mountain 3C: Desert 5D: Imperial Avenue 4D: Ghost Forest SE: Cape Way
Game Flow
- Versus Mode Entry
After inserting coins and pressing the Start Button, Versus Mode Entry prompts will be displayed for potential players at other game cabinets. Pressing the Start Button within the Versus Mode Entry period will start Versus Mode.
Closing Versus Mode Entry
To close Versus Mode entry, press the View Change Button and the Brake pedal at the same time before other players join. (Press the Brake pedal while holding down the View Change Button.)
Versus Mode entry time can also be run down to “0” by holding the Start Button, thus closing Versus Mode entry.
By closing Versus Mode entry in either of the above ways, the Single Player mode will commence, provided no players have already joined.
- Car Selection
& Testorosat ForravyY
Neer Setection,
You can select the car model. In Single Player mode you can also change the car color. Press the Brake pedal and Shifter together to change the car color. (Press up or down on the shifter while holding down the Brake pedal.) These instructions will not be displayed on the screen.
Moving the Shifter up or down while holding down the Brake pedal will bring up a two-character car color code just above the “Gas Pedal: Enter Selection’ indicator in the lower right corner of the screen. The color codes are represented as follows: RE:red, YE:yellow, BK:black, WH:white, SL:silver, GR: green, LB: light blue, BU:blue.
Changing the car model in the middle of color selection will automatically return the color to the selected model’s default color, after which model and color selection will again be possible. The selected car will then be displayed in the chosen color at the start of the game.
The available colors vary from car to car. The colors available for each car are indicated by a ‘Yes’ in the chart below, and likewise, only these colors will be shown during selection.
Color Chart
| Car Type | Black Blue | Green Light Blue | Red | Silver White Yellow | ||||
| F50 | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| 360 Spider | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Dino 246 GTS | Yes | No | No | Yes | Yes | Yes | Yes | Yes |
| 365 GTS/4 Daytona | Yes | No | No | Yes | Yes | Yes | Yes | Yes |
| Testarossa | Yes | No | No | No | Yes | Yes | No | Yes |
| 288 GTO | Yes | No | No | Yes | Yes | No | Yes | Yes |
| Enzo Ferrari | Yes | No | No | No | Yes | Yes | No | Yes |
| F40 | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Player-selectable cars and their characteristics are shown below. The color shown in parenthesis is the default color.
+ F50 (RE), 360 Spider (RE) (For INTERMEDIATE Player) Acceleration — : ****** Handling | deed Top Speed | desea
~ Dino 246 GTS (YE), 365 GTS/4 Daytona (BK) (For NOVICE Player) Acceleration —: *****##* Handling sooo Top Speed ladle
~ Testarossa (RE), 288 GTO (RE) (For INTERMEDIATE Player) Acceleration —: **###*###4# Handling neta Top Speed Tea
~ Enzo Ferrari (RE), F40 (RE) (For PROFESSIONAL Player) Acceleration — : ****** Handling aii Top Speed | dboedobac de
- Transmission Selection
You can choose between Automatic transmission and Manual transmission.
When Manual transmission is selected, the number of gears varies with the car model. + 6-speed: F50, 360 Spider, Enzo Ferrari + 5-speed: Dino 246 GTS, 365 GTS/4 Daytona, Testarossa, 288 GTO, F40
- Mode Selection
In Single Player, you will choose a game mode.
- OutRun Mode
- Total Time
- Time Counter
- Score
- Route Map
- Tachometer
- Shift Up Indicator
- Speed Meter
- Shift Indicator
This is the pure driving mode, enjoyed with a young lady by your side. You select branching paths and try to reach the goal within the time limit. The game ending varies depending on which goal is reached.
- Heart Attack Mode
- Lady’s Heart Meter
This is the mode where you raise the Lady’s Heart Meter by fulfilling her requests. Collect as many of the hearts showing her feelings as possible. ‘You must pursue her request for the duration of the indicated track section.
©The Lady’s Requests
+ Drift more!” Try drifting continuously throughout the track section.
- Keep passing cars!” Pass as many cars as possible throughout the track section.
- Don’t crash!’ Avoid hitting any other cars, walls, or obstacles throughout the track section.
- Run through red/blue!’ Drive on the indicated color section of the roadway.
“Hit the blue cones!’ There are twenty blue cones placed on the roadway—try to hit as many as you can.
ot eer ey
+ Cut the line!’ Drive through the yellow heart lines between cars on the roadway. Lines cut once will not come back.
- Catch the Heart! There are Hearts floating around on the roadway. Try your best to drive through the Hearts. Hearts collected once will not come back.
© Special Requests Satisfying certain conditions will open up Special Requests.
© Ending The game ending will change depending on your performance assessment.
- Time Attack Mode
- Sector Time
- Position
This mode is a test of time in reaching the goal. Player driving data is recorded for goal time, route best time, and slowest time. The player can then compete against his own time in subsequent plays. When there is no player data recorded, a default data car will appear.
© Ending The game ending will change depending on your goal time.
© Internet Ranking Password If your time qualifies, you'll be given an Internet Ranking password. Using this password, you can participate in the Internet Ranking system.
© Goal Choice You can choose from five different destination goal points. (This option is only available in the Time Attack Mode.)
© Route Choice
After choosing a goal, you can decide on a specific route for that particular goal. (This option is only available in the Time Attack Mode.)
There is one exception, however—Goal A, ‘Tulip Garden’, and Goal E, ‘Cape Way’ each have only one route so the Route Choice option will not be available. Goal B, ‘Metropolis’, and Goal D, ‘Imperial Avenue’ each have four possible routes, while Goal C, ‘Ancient Ruins’ has six possible routes to choose from.
& BGM Selection
There are seven different in-game songs to select from. In Versus Mode, each player can listen to his or her own individual selection.
+ SPLASH WAVE(from original OutRun)
- MAGICAL SOUND SHOWER (from original OutRun) + PASSING BREEZE(from original OutRun)
- Risky Ride(new)
- Shiny World(new) + Night Flight(new, includes lyrics)
Versus Play
- Versus Mode Game Play
The car colors for versus mode are fixed for each player. 1P: Red, 2P: Yellow, 3P: White/Silver (depending on car model), 4P: Black
The position order on the starting grid is determined by the order of Versus Mode entry (decided by who presses the Start Button first).
The course is decided as the route taken by whoever first reaches a given course branch.
- Special Versus Mode Commands
The ‘No Handicap’ and ‘Player Only’ modes are selectable with special commands entered at the game’s selection screen.
- No Handicap Mode
In the usual Versus Mode, the player in second place during a race can catch up easier with computer assistance, but this assistance isn’t available in the No Handicap mode.
To activate No Handicap mode, all participants in the Versus Mode competition must press the Brake pedal together with the Shifter up. (Push the shifter up while holding down the Brake pedal.) An icon will be displayed on the right side of the selection screen when this mode is activated.
- Player Only Mode
In Player Only mode, no cars besides the player-controlled cars will appear in the race.
To activate Player Only mode, all participants in the Versus Mode competition must press the Brake pedal together with the Shifter down. (Push the shifter down while holding down the Brake pedal.) An icon will be displayed on the right side of the selection screen when this mode is activated
Gameplay Techniques and Secret Commands
- How to Drift
After letting go of the Gas pedal, immediately press the Brake pedal. Then, quickly steer sharply into the turn and press the Gas pedal.
In the case of Manual transmission, shift down one gear just before the turn, then immediately steer sharply into the turn.
- Mid-game Quit Command
reolly want to quit t! ve 1 « best b eid, vee Mises
You can quit in the middle of a game. This command is only possible in the Single Player mode.
To activate the mid-game quit command, stop the car and press the Brake pedal, View Change button, and Shifter up. (While holding down the Brake pedal, continue to hold down the View Change button, and finally press the Shifter up.)
After inputting the command, the player is prompted, ‘Do you really want to quit this game? Yes/No’. Choosing ‘Yes’ will finish the game, and ‘No’ will return the player to the game.
There are three conditions under which this command cannot be executed. +The player is near the starting grid. *The remaining time is under 8 seconds. *’No’ has already been chosen once.
Gameplay Techniques and Secret Commands
- Driver
Name: Alberto
Personal Info: Although easy-going on the outside, he’s a real go-getter. He has a very distinguished driving sense. He’s also quite rich.
- OutRun Mode Lady
Name: Jennifer
Personal Info: She’s a filthy rich ‘princess’, always selfishly seeking the next thrill. She’s involved with Alberto, his Ferrari a present from her. She has a sharp eye for driving techniques.
- Heart Attack Lady
Name: Clarissa
Personal Info: She’s peppy and unmistakably sexy. A driving fan, with a weakness for thrill rides. She’s very demanding, but her sweet character makes her hard to dislike.
- Game Test Mode
[IMPORTANT] When changing the game configuration, changes will not be enabled until the Game Test Mode has been completed. Be sure to exit the Game Test Mode properly after configuration changes.
Select GAME TEST MODE from the System Menu screen to display the Game Test Menu screen as follows. Use the SERVICE Button to move the cursor to the desired test item. Press the TEST Button to enter the selected
item.
GAME TEST MODE
INPUT TEST OUTPUT TEST DRIVE BOARD TEST GAME ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR
> EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
<GAME TEST Menu screen>
Afier selecting an item, read the explanations below regarding operation.
After the test is complete, move the cursor to EXIT and press the TEST Button to return to the System Menu screen.
A. INPUT TEST
Select INPUT TEST to display the following screen and check the status of input devices. This test should be used periodically to check that each input device is functioning correctly.
GAME TEST MODE
STEERING 70H GAS 22H
BRAKE 23H
GEAR POSITION N START OFF VIEW CHANGE OFF SERVICE OFF TEST OFF
PRESS TEST AND SERVICE BUTTON TO EXIT
<INPUT TEST screen>
Test the STEERING, GAS (ACCEL) and BRAKE controls to ensure that they are functioning properly and that the parameters change smoothly as each input device is operated.
Display N, UP and DOWN using the GEAR POSITION. N displays that there is no control input. Verify that both UP and DOWN display in sync with the position of the shift knob.
Press the START, CHANGE VIEW, SERVICE and TEST Buttons. If functioning correctly, each indicator will switch from OFF to ON.
Press the SERVICE and TEST Buttons simultaneously to return to the Game Test Menu screen.
B. OUTPUT TEST
Select OUTPUT TEST to display the following screen and check the status of each lamp. This test should be used periodically to check that the lamps are functioning correctly.
On this screen the cursor will switch automatically between items, lighting up the respective lamps.
OUTPUT TEST
START BUTTON > VIEW CHANGE BUTTON
PRESS TEST BUTTON TO EXIT
<OUTPUT TEST screen>
@ START BUTTON : Lights up the START button. @ VIEW CHANGE BUTTON: Lights up the View Change button.
Press the TEST Button to return to the Game Test Menu screen.
C. DRIVE BOARD TEST
Select DRIVE BOARD TEST to display the following screen and check the status of steering motor.
Use the SERVICE Button to select the desired test item. Press the TEST Button to activate the selected item.
DRIVE BOARD TEST
STOP MOTOR ROLL RIGHT ROLL LEFT CENTER OF STEER ‘28 RIGHT LEFT MOTOR POWER 80 > EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
<DRIVE BOARD TEST screen>
@ STOP MOTOR: Halts motor activity. @ ROLL RIGHT: Rotates steering wheel completely to the right. @ ROLL LEFT: Rotates steering wheel completely to the left. @ CENTER OF STEER: Steering wheel motor’s center of control is displayed. :RIGHT: Moves center of control position to the right. :LEFT: Moves center of control position to the left. @ MOTOR POWER: Sets the steering resistance. There are four levels to choose from, 100% (strong resistance), 90%, 80%, and 60%(weak resistance). (80% is the default setting)
Afier changing the settings, select EXIT and press the TEST Button to return to the Game Test Menu screen.
D. GAME ASSIGNMENTS
Select GAME ASSIGNMENTS to display the current game settings and make changes.
Changes to settings are not enabled until Test Mode is exited. After changing settings, be sure to exit Test Mode.
GAME ASSIGNMENTS
DIFFICULTY NORMAL, CABINET STANDARD ADVERTISE SOUND ON LANGUAGE JAPANESE SPEEDOMETER KILO QUICK START OFF LINK ID 1 TOTAL MACHINE 1 GROUP. 1 > EXIT
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
<GAME ASSIGNMENTS screen>
Perform the following settings for each item.
@ DIFFICULTY: The game difficulty setting. There are 5 difficulty levels with VERY EASY being the easiest setting and VERY HARD being the most difficult setting. (Default Setting: NORMAL)
@ CABINET TYPE: The game cabinet type setting. Choose from either STANDARD or UPRIGHT.
@ ADVERTISE SOUND: The setting to turn the advertising sound ON/OFF. (Default Setting: ON)
@ LANGUAGE: The game language setting. Choose from either JAPANESE or ENGLISH. (With JAPAN as the Country Setting, the default LANGUAGE setting is JAPANESE. ENGLISH is set as the default for a Country Setting of USA or EXPORT.)
@ SPEEDOMETER: The speed display setting. During game play, KILO will be displayed as “km/h”, and MILE as “mph”. Choose one of these options. (With JAPAN or EXPORT as the Country Setting, the default SPEEDOMETER setting is KILO (km/h). MILE (mph) is set as the default for a Country Setting of USA.)
@ QUICK START: Choose OFF or ON. The ON setting takes the player directly to the game selection screen after entering credits into the machine. (Default Setting: OFF)
@ LINK_ID: The setting which determines the Player Number of each cabinet. It assigns unique numbers for cabinets in a single group. Do not assign two or more cabinets the same number. For network play, it is necessary to complete the LINK_ID, TOTAL MACHINE, and GROUP settings for each cabinet. (Default Setting: 1, Maximum: 4)
@ TOTAL MACHINE : The number of network connected game cabinets. (Sets the number of competing cabinets in Versus Mode.) Setting this to “1” limits possible play modes to Single Player mode only. (Default Setting: 1, Maximum: 4)
@ GROUP: Used for dividing networked cabinets into groups. For example, to split up a group of four networked machines into two groups of two cabinets, set two cabinets to “1” and the other two cabinets to “2”. Generally, setting all cabinets to “1” is recommended.
After changing the settings, select EXIT and press the TEST Button to return to the Game Test Menu screen.
<Network Versus Mode Cabinet Settings>
Cases for four cabinets (A, B, C, and D) connected via network cable.
4-Cabinet Versus
| | CABINET | A | B | C | D |
| | LINK_ID | T | Z | 3 | |
| TOTAL MACHINE | 4 | 4 | 4 | 4 |
| GROUP | I | I | I | I |
Status our cabinets can compete.
3-Cabinet Versus
| | CABINET | A | B | Cc | D |
| [LINK_ID | T | T | z | 3 |
| | TOTAL MACHINE | | T | 3 | 3 | 3 |
| GROUP | I | 2 | 2 | 2. |
Status Single play Three cabinets can compete. only.
2-Cabinet Versus
| | CABINET | A | B | Cc | D |
| [LINK_ID | T | z | T | 2 |
| | TOTAL MACHINE ——‘[2 | Zz | z | 2 | |
| | GROUP | I | I | 2 | 2 |
| Status | Two cabinets can compete. | Two cabinets can compete. |
E. BOOKKEEPING
Selecting BOOKKEEPING will display the following screen. All up-to-date operation data will be displayed on two BOOKKEEPING screens.
Use the TEST Button to cycle between the first screen (BOOKKEEPING 1/2) and the second screen (BOOKKEEPING 2/2). BOOKKEEPING 1/2
[CREDIT INFO} COINL 0 COIN2 0 TOTAL COINS: 0
COIN CREDITS: 0 SERVICE CREDITS: 0 TOTAL CREDITS: 0
NUMBER OF GAMES: TOTAL TIME:
PLAY TIME:
AVERAGE PALY TIME:
PRESS TEST BUTTON TO CONTINUE SELECT WITH SERVICE B UTTON
< BOOKKEEPING 1/2 screen>
@ COIN CHUTE #1: The number of coins inserted into Coin Slot 1. @ COIN CHUTE #2: The number of coins inserted into Coin Slot 2. @ TOTAL COINS: The total number of coins inserted into the coin slots.
@COINCREDITS: The number of credits for the coins inserted.
@ SERVICE CREDITS: The number of credits input by the SERVICE Button. @TOTALCREDITS: Total credits from coins and the SERVICE Button.
@ NUMBER OF GAMES: The total number of games played. @ TOTAL TIME: The amount of time the unit has been in operation. @ PLAY TIME: Total playing time. @ AVERAGE PLAY TIME: Total play time divided by the total number of games played. Press the TEST Button to move to screen 2/2 of BOOKKEEPING.
BOOKKEEPING 2/2
[GAME MODE INFO}
OUTRUN MODE PLAYERS: 0 GOAL PLAYERS: 0 GOAL AVE TIME: 0°00°00 SELECT AVE TIME: 0°00°00
HEART ATTACK MODE PLAYERS: 0 GOAL PLAYERS: 0 GOALAVE TIME: 0°00°00 SELECT AVE TIME: 0°00°00
TIME ATTACK MODE PLAYERS: 0 GOAL PLAYERS: 0 GOAL AVE TIME: 0°00°00 SELECT AVE TIME: 0°00°00
VS MODE PLAYERS: 0 GOAL PLAYERS: 0 GOALAVE TIME: 0°00°00 SELECT AVE TIME: 0°00°00
PRESS TEST BUTTON TO CONTINUE SELECT WITH SERVICE B UTTON
< BOOKKEEPING 2/2 screen>
This shows the number of plays and the respective play times. This histogram should be referred to when setting the Game Difficulty.
Press the TEST Button to return to the Game Test Menu screen.
F. BACKUP DATA CLEAR
Select BACKUP DATA CLEAR to clear the contents of BOOKKEEPING, ranking data and coin/credit data.
BACKUP DATA CLEAR
YES (CLEAR) > NO (CANCEL)
SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON
< BACKUP DATA CLEAR screen>
To clear data, use the SERVICE Button to move the cursor to YES (CLEAR) and then press the TEST Button. When the data has been cleared, the message “COMPLETED” will be displayed.
Press the TEST Button again to return to the Game Test Menu screen.
Move the cursor to NO (CANCEL) and press the TEST Button to return to the Game Test Menu screen without clearing the data.
- EXPLANATION OF TEST AND DATA DISPLAY
By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable. This product's basic system consists of the Chihiro game board and the GD-ROM drive. The system enables you to play several games one after the other just by changing a GD-ROM disc that is to be set on the GD-ROM drive. The product supports, therefore, the following 2 test modes:
- System test mode for an automatic self-diagnostic test (generally used by every product that contains the basic system) and a coin assignment (specifically used by this product) and
- Game test mode for testing the input/output control devices and setting the difficulty level (specifically used by this product).
TABLE 10 EXPLANATION OF TEST MODE
ITEMS DESCRIPTION
INSTALLATION When the machine is installed, perform the following: OF MACHINE 1. Check to ensure each is the standard setting at shipment.
- Check each Input equipment in the INPUT TEST mode.
- Check each Output equipment in the OUTPUT TEST mode.
- Test on-IC-Board IC's in the self-test mode.
MEMORY TEST This test is automatically executed by selecting RAM TEST, or ROM BOARD TEST in the Menu mode.
PERIODIC Periodically perform the following: SERVICING 1. MEMORY TEST
- Ascertain each setting.
- To test each Input equipment in the INPUT TEST mode.
- To test each Output equipment in the OUTPUT TEST mode.
CONTROL . To check each Input equipment in the INPUT TEST mode. SYSTEM 2. Adjust or replace each Input equipment.
- If the problem still remains unsolved, check each equipment's mechanism movements.
MONITOR In the Monitor Adjustment mode, check to see if Monitor (Projector) adjustments are appropriate.
IC BOARD 1. MEMORY TEST
- In the SOUND TEST mode, check the sound related ROMs.
DATA CHECK Check such data as game play time and histogram to adjust the difficulty level, etc.
10-1 SWITCH UNIT AND COIN METER
A\ Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit accidents.
@ Adjust the sound to the optimum volume, taking into consideration the environmental requirements of the installation location. @ Removing the Coin Meter circuitry renders the game inoperable.
SWITCH UNIT ( \ fe) SPEAKER TEST SERVICE OEMAG. 0 Open the coin chute door, and the switch unit shown will appear.
The functioning of each SW is as follows: KK
A B Cc
FIG. 10. 1 a SWITCH UNIT
A SPEAKER VOLUME SWITCH: Adjusts sound volume for all of the machines' Speakers. (VOLUME)
B_ TEST BUTTON: For the handling of the test button, refer to the following pages. (TEST)
C SERVICE BUTTON: Gives credits without registering on the coin meter. (SERVICE)
D DEMAGNETIZER BUTTON: Eliminates the on-screen color unevenness due to magnetization of CRT. (DEMAG)
Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. First use this SW before performing the monitor's color adjustment.
NI
Coin Meter
i FIG. 10.Tb
- HANDLE MECHANISM
In order to prevent an electric shock and short circuit, be sure to turn power off before perform ing work by touching the interior parts of the product.
In the test mode, if the steering wheel’s VR variations are not within the allowable range, the VR installation position adjustments or VR replacement is needed. Also, be sure to apply grease to the VR gear portion once every 3 months.
11 - 1 REMOVING THE CONTROL PANEL
Turn the power switch off. Remove a total of 4 tamperproof screws from both sides of the control panel’s front. Remove the two tamperproof screws fromthe underside of the control panel. Wiring connectors are connected inside the control panel. Carefully draw the control panel in a mnner so as not to damage wiring. Disconnect the wiring connector. Q@ CECO
TAMPERPROOF SCREW (black) (6} U8 x 30
11 - 2 REPLACING AND ADJUSTING THE HANDLE’S VR
WARNING!
Never touch places other than those specified. Touching places not specified can cause electric shock and/or short circuit. After the replacement or adjustment of the VR, be sure to set the variable value of the VR in the test mode’s Volume Setting.
REPLACING THE VOLUME
oO) Turn off the power. @ Disconnect the connector. @ Take out the 2 screws which secure the volume Bracket and remove the Volume Bracket. ® Take out the 2 screws to remove the Volume Gear and replace the Volume. © After replacing the Volume, perform Volume setting in the Volume Setting Mode.
ADJUSTING THE VOLUME
CICRCICIC) In the Test Mode, have the Volume value indicating screen displayed. Loosen the 2 screws which secure the Volume Bracket to disengage Gear Mesh. With the Steering Wheel in the centering position, cause gears to be engaged in the manner so that the Volume Shaft is in the status shown below.
Fasten screws which secure the Volume Bracket.
Perform Volume setting as per the Volume Setting Mode.
220-5373 220-5484
MLX8, w/flat
VR_BRACKET "D"CUT FACE
11 -3 GREASING
Never touch places other than those specified. Touching places not specified can cause elec tric shock and/or short circuit.
Apply greasing to the Volume gear mesh portion every 3 months.
SPRING DYN-1269
O
SLIDING FACE OF CAM
- SHIFT LEVER
CAUTION!
In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product. Be careful not to damage wiring. Damaged wiring can cause electric shock or short circuit. Do not touch places other than those specified. Touching places other than those specified can cause an electric shock or short circuit accident.
If the Shift Lever operation is not satisfactory, remove the Shift Lever in the following procedure and replace the microswitch.
12-1 REMOVING THE SHIFT LEVER
ClO RCIC) Turn Power off.
Take out the 4 SPECIAL BOLTS and pull the SHIFT LEVER UNIT upward by paying careful attention so as not to damage the wiring. Disconnect the 2 connectors to allow the unit to be removed.
When reinstalling, follow the procedure oppisite as when removing. At this time, ensure that*DOWN” display
TAMPERPROOF SCREW (4) M5. X12, black appears on the upper part as shown.
12-2 SWITCH REPLACEMENT
Each microswitch is secured with 2 screws. Remove the 2 screws and replace the Microswitch.
TAPPING SCREW (2) M3 X 16
GREASING
509-5704
After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode.
- ACCEL & BRAKE(S)
In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. 7 = Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit!
If Accel and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every three months.
13 - 1 ADJUSTING AND REPLACING THE V.R.
When released: When stepped on:
ACCEL: Under 30 H Over COH
BRAKE: Under 30 H Over COH
Check Volume values in the Test Mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not specified can cause an electric shock or short circuit. TRUSS SCREW. MAX, chrome 2)
® Take out the 2 truss screws and remove the Front Cover from the Accel. & Brake unit.
Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base. Secure the Potentiobase. ee © Perform Volume setting in the Volume Setting Mode.
SCREW MSX 12, FRONT COVER
wiflat washer
POTENTIOBASE.
20-5373 220-5484
Check Volume values in the Test Mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not speci- TRUSS SCREW (2) {fied can cause an electric shock or short circuit. MEXS eoTENTTOCOVER,
Take out the 2 truss screws and remove the Front Cover
from the Accel. & Brake unit.
Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base. Secure the Potentiobase. G© © OC Perform Volume setting in the Volume Setting Mode.
POTENTIOBASE —E_ ee
13 -2 GREASING
Once every 3 months, apply greasing to the Spring and Gear Mesh portion.
- COIN SELECTOR
HANDLING THE COIN JAM
If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.
CLEANING THE COIN SELECTOR
(10?) @ Remove and clean smears by using a
soft cloth dipped in water or diluted
IMPORTANT! chemical detergent and then squeezed
dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.
The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below:
- Turn the power for the machine OFF. Open the coin chute door. (2)Remove the coin selector from the coin chute door.
- Open the gate and dust off by using a soft brush (made of wool, etc.).
- Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (5)Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. (6)Remove stain from the rotary shaft and shaft receiving portions by wiping off with a soft cloth, ete.
- After wiping off as per (6) above, further apply a dry cloth, etc. to cause the coin selector to dry completely. Insert a coin while keeping COIN INSERTION TEST the Reject Button pressed down and check if it is rejected. Once every month, when performing the Coin SW Test, simultaneously COIN METER check the following: —
@ Does the Coin Meter count satisfactorily? @ Does the coin drop into the Cashbox correctly? @ Is the coin rejected when inserted while keeping the Reject Button pressed down? FIG. 14
COIN DOOR
Tom Happ {om hap @beppcontols.com Happ Controls 106 Garlisch Drive Elk Grove, IL. 60007 Ph. 847-593-6161 ext, 107 Fx, 847-956-2091
Visit our website htip://www.happcontrols.com 42-0641-00 iL 42-0405-00 YELLOW 25¢ (FITTED AS STANDARD) 42-0231-00
42-0517-05
42-7201-00 EXCLUSIVE!
Custom "Guardian" Secu = tect your lars, LOWERDOOR — 42-3145-16- FRAME 42-3272.00 DOOR SCREWS 43-0183-00 DORE FRAME 42.3227-00
OPTIONAL DOLLAR BILL ACCEPTOR
@ THE COIN DOOR ASSEMBLY USED ON JAMBO SAFARI STD COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIR- ING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.
@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDA- TORS:
HOLE POSITION#1 Mars 2000 series (FORWARD-MOST POSITION)
HOLE POSITION#2 Mars 2000 series DBV45 (JCM)
HOLE POSITION #3 CURRENTLY NOT USED
HOLE POSITION #4 DSI01*
*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.
The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.
- MONITOR
15-1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS
Before handling the monitors, be sure to read the following explanations and comply with the
Indicates that access to a specific part of the Indicates the instruction to disconnect a power equipment is forbidden. connector or to unplug.
When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor interior and the monitor, be sure to disconnect the power connector (plug) before starting the work. Proceeding the work without following this instruction can cause electric shock or malfunctioning.
Primary side and Secondary side The monitor's circuit which is divided into the Primary side SECONDARY SIDE and Secondary side, is electrically isolated. Do not touch (Chassis, CRT) the primary side, or do not touch both the primary side
dangerous. When making monitor adjustments, use a non- WA
conductive driver and make adjustment without touching any part other than the Adjustment V. R. and knob. Also, be sure not to cause a short-circuit to the Primary side and Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous. High-tension Voltage Some of the parts inside monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor interior, turn the power off so as not to cause malfunctioning or fire hazard.
ANODE CAP PRIMARY SIDE DEMAGNETIZER COIL REAR PART ANODE LEAD | mamep ‘Approx. 29 kV
DEMAGNETIZER ® FOCUS LEAD
COIL 1 (black) Approx. 10 kV
SECONDARY SIDE FBT Approx. (Chassis, sheet metal work, CRT, ete.) & Difconnect ortunplig, 29kV
@ Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulatively charged as time elapses, generating high-tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as is assembled" condition. If these are disassembled, what's charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.
© Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. ‘This is because the CRT surfaces are subject to static and will not adversely affect the human body. © Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are
53 ww
For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points.
@ Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on the CRT surfaces.
@ Avoid applying stickers, seals, etc. on the CRT face. Aluminum Foil @ Do not remove aluminum foils from the CRT corners. Removing the aluminum foils can cause static prevention effects to be lowered.
15-2 CLEANING THE CRT SURFACES
Static preventive coating is applied to the CRT surfaces. When cleaning, pay attention to the following points. Peeling off of static preventive coat can cause
Remove smears by using a dry, soft cloth (flannels, etc.). Do not use a coarse gauze, etc. For smear removing solvent, alcohol (ethanol) is recommended. When using chemical detergent, be sure to follow instructions below: Dilute chemical detergent with water and dip a soft cloth in and then thoroughly wring it to wipe smears off. Do not use a chemical detergent containing an abradant, powder or bleaching agent. Do not use alkaline chemical detergents such as "glass cleaner" available on the market or solvents such as thinner, etc. Do not rub or scratch the CRT face with hard items such as brushes, scrub brush, etc.
Clean the CRT surfaces once a week. When cleaning, pay attention to the above caution so that the antistatic coating will not come off.
- PERIODIC INSPECTION TABLE
The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation. When handling the controller, the player will be in direct contact with it. In order to always allow the player to enjoy the game, be sure to clean it regularly. Also, it is advisable to provide wet tissue, etc. available for player use.
WARNING!
Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause fire and electric shock hazards. Never use a water jet, etc. to clean inside and outside the cabinet. If wetness occurs for any reason, do not use the product until it has completely dried. Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the internal cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident. Note that cleaning the interior parts can be performed on a pay-basis.
TABLE 16
TTEMS DESCRIPTION PERIOD CABINET Check Adjusters'contact with surface. CONTOROL PANEL Cleaning Inspection of VR Monthly Inspection of adjusting gear mesh Trimonthly
Greasing Trimonthly Greasing Trimonthly
| SHIFT LEVER | Inspection of SW | Monthly |
| ACCEL. & BRAKE | Inspection of VR | Monthly |
Gear and Spring portion greasing Trimonthly MONITOR
COIN CHUTE DOOR SCREEN cleaning. Weekly Check adjustments. Monthly or when moving. Inspection of COIN SW Monthly Coin insertion test Monthly Cleaning of COIN SELECTOR. Trimonthly
| SEAT | Greasing to the seat rail | Trimonthly |
| GAME BD | MEMORY TEST | Monthly |
Check settings. Monthly
| POWER SUPPLY PLUG | Inspection and cleaning | Annually |
INTERIOR Cleaning CABINET SURFACES, Cleaning
CLEANING THE CABINET SURFACES
When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.
SEAT (Greasing to Seat Rail Portion)
Move the Seat to the rearmost position and apply spray greasing to the portion shown at the right
once every 3 months . if and backward so as to allow the grease to be
After greasing, move the Seat a few times forward and backward so as to allow the grease to be — applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the Seat Rail, or any excess grease.
FIG. 16
- GAME BOARD
mn In order to prevent electric shock and short circuit hazards, be sure to turn power off : "a before performing work.
nN In this product, setting changes are made during the test mode. The Game BD need | not be operated. Use the Game BD, etc. as is with the same setting made at the time of
(0?) When having the game board replaced or repaired, use the included carton box to ship it. Do not disassemble it. If the board is not received in the proper condition, it may not be
17-1 REMOVING THE GD-ROM DRIVE
@ Tur the power off.
@ Open the game unit
@ Remove the GD cable connector and the power cord connector from the GD-ROM drive.
POWER CORD CONNECTOR, GD CABLE CONNECTOR
Release the cables.
PHOTO 19. la GD CABLE CONNECTOR
@ Remove the 4 screws to remove the GD-ROM drive.
SCREW (3) M4x16, wiflat & spring washers
PHOTO 19. 1b
17-2 COMPOSITION OF THE GAME BOARD
Game Board. Gror) Once the Chihiro Board has the Key Chip inserted, it is this product's specialized
ASSY CASE BOX ORT
KEY CHIP.
AVIP CABLE. 600-7274-150
FIG. 17.2a
Use this product with the DIP SW settings shown in the figure below.
‘beongecs
FIG. 17.26
17-3 REPLACING THE MAIN BOARD BATTERY
@ To prevent overheating, explosion, or fire: + Do not recharge, disassemble, heat, incinerate, or short the battery.
To avoid risk of malfunction and damage: @ Make sure the positive and negative ends are aligned correctly.
of use, it is usually an indication of a problem or abnormality with something other than the battery. Be sure to inspect the board that the battery is connected to. Gror) If an error appears indicating that the battery power is very low within the first year
BUTTON BATTERY CR2032 @ There is a Media Board Button Battery underneath the Media Board. 401-0054 4
\, SCREW (4), black M3 X65
[_STIGHT SCREW (6), black M3X6
MEDIA BOARD
HOLDER MAIN BOARD XS FIG. 16.3
@ Carefully remove the battery from its holder.
@ Insert a new battery into the holder with the "+" terminal facing up.
17-4 REPLACING THE MEDIA BOARD BATTERY PACK
Prohibitions and Cautions to Handle the Battery Pack
Do not disassemble the battery pack and the batteries. If you should fail to observe this instruction, the internal wires and/or protective devices may be damaged; as a result the safety system may not function when discharging and recharging, eventually causing an overheating, fire and explosion. If you should disassemble the batteries, the generated gases may harm your throat and the negative plate may overheat and make a fire. Do not make an external short circuit of the battery pack and the batteries. If you should fail to observe this instruction, the batteries may overheat, make a fire, and explode. Do not fire the battery pack and the batteries. If you should fail to observe this instruction, the batteries may make a fire and explode. Do not leave the battery pack and the batteries nearby the heat source (fire or heater) or under the intense direct sunlight and flaming sun. If you should fail to observe this instruction, the batteries may reduce the service life and in the worst case may overheat, make a fire, and explode. Do not leave the battery pack and the batteries in water or seawater. Also do not apply water or seawater onto the battery pack and the batteries. If you should fail to observe this instruction, the internal wires and/or protective devices may be damaged; as a result the safety system may not function when discharging and recharging, eventually causing an overheating, fire and explosion. Also water may be electrolyzed into oxygen and hydrogen, and eventually the battery's sealed section may be corroded and the internal liquid may leak. Do not solder on the battery pack's terminals. If you should fail to observe this instruction, the armor may be heated and melted or the internal wires may be damaged, eventually causing an overheating, fire and explosion. Also, when the battery's temperature reaches to 100° or more, the battery may leak its internal liquid due to destruction of its plastic parts (gasket, separator, etc.), or may overheat, make a fire, or explode due to internal short-circuit. Do not insert or connect the battery in a reversal polarity. If you should fail to observe this instruction, the battery may be externally short-circuited and eventually overheat, make a fire, or explode, depending on the device you connect with.
Do not tightly seal the battery pack when installing it onto an external device. Flammable gas is generated from the battery when its safety mechanism has
If the GD-ROM read time becomes excessively long, it is likely that the Media Board battery pack life if running low. No battery pack charger is available. Follow the procedure to replace the battery pack.
Remove 4 screws from the upper face of the board.
Remove the top cover.
Remove | tapping screw and remove the cover battery holder.
Disconnect the connector at the end of the wire coming out of the battery pack. Remove by pressing the projection on the connector and pulling.
Securely connect the new battery pack.
Attach the cover battery holder and top cover.
Submit the used battery packs to an industrial waste disposal plant. Thus they must be disposed according to the local laws and the regulations in your country.
SCREW (4), black / M3X65
Zl
‘\__TOP COVER
‘ — TAPPING SCREW (1), black
| H | SO | 3X8 |
LA
| ' | ; | COVER BATTERY HOLDER | |
| | | | | a | BATTERY PACK |
401-0081 CONNECTOR
MEDIA BOARD
FIG. 16.4
- NETWORK PLAY
Up to 4 machines can be linked for network play. Properly connected network cables and correct network play settings are required for network play.
18-1 PRECAUTIONS REGARDING NETWORK PLAY SETUP
nN Before starting to work, ensure that the Power SW is OFF. Failure to observe this WARN j can cause electric shock or short circuit. fs (! Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the site maintenance individual or other skilled professional. Performing work by non-technical personnel can cause electric shock hazard. When linking a number of machines, be sure to supply sufficient power for the corresponding number of machines. Be sure to secure per machine current as stated in this manual. Failure to observe this can cause a fire and an electric shock accident. Due to the length of the network cable, the distance in between the machines is limited. However, to avoid accidents, be sure to secure space in excess of 70 cm between the machines. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.
J @ To perform work safely, be sure to secure the space corresponding to number of machines to be linked. Failure to observe this can cause accident.
(10?) Network play is not possible between game machines with different cabinet types.
IMPORTANT!
When connecting several games machines together, make sure that a sufficient amount of electrical power is available for each machine. Plan on providing 7A for each machine in 100-120V locations, and 4A in 220-240V locations.
SPACING OF GAME MACHINES,
Be sure to secure space in excess of the described distance between machines.
706nm
200nm La
FIG. 18.1 700nm
18-2 CONNECTING NETWORK CABLES
To enable network play, the hubs inside each of the game machines involved must be connected with network (LAN) cables. Connect the hub inside one of the machines to the hubs in each of the other machines using LAN cables. There is no need to connect the other machines to each other.
Do not connect LAN cables to game machines when they are not used for network play.
@ Turn off the power and unplug the power cord from the outlet. Place the power cord so as not to damage it while working.
@ Move the machines so that they are lined up. Leave enough space on the back lid side of the machine to perform the rest of the operations in this procedure.
@ Pass the LAN cable through the edge holder (the rectangular frame-shaped plastic part.) Pressing down on the edge holder from above will cause it to stretch elastically and open up.
@ Plug the connector on the end of the LAN cable into port 2 or above on the hub. Port 1, located at the front closest to the front lid, is connected to the CHIRIHO in the base interior. Any of the ports 2 or above can be used to connect to any of the other game machines. Since the hub in one machine will be connected to the hubs in each of the other machines via LAN cables, only one machine needs to be fitted with enough LAN cables for all machines involved. The other machines will only have 2 cable connections each.
@ Once the machines have been linked for network play, line them up. Leave as much space as possible between the machines.
@ Connect the power cord and grounding wire for each machine.
- DESIGN RELATED PARTS
999-2109 Marquee Artwork ORTS 999-1430 Label Epilepsy Warning ORTS
999-2117 Decal Instruction CPanel ORTS
FRI-2002 Steering Emblem FRI
999-2104 Decal Monitor Side Right ORTS.
999-2103 Decal Monitor Side Left ORTS 999-2108 Decal Seat Back ORTS
999-2105 RPM Gauge 999-2115 Speed Gauge
999-2116 Decal Switches ORTS
999-2106 cal Base Rear ORTS
999-2107 Decal Base L&R X2 ORTS 999-1966 Decal Instruction ORTS
- PARTS LIST
ITEM NO. PART NO.
1 999-1961 2 Local Purchase 3 999-0167 4 999-0168 5 999-2081 6 999-2111 7 Local Purchase 8 999-2110 9 610-0408-91 10 INY-1204 11 DYN-1223X 12 999-1596 13 SPG-2200 14 999-2010 15 DYN-1209X, 16 999-2114 17 999-1604 18 ORTT-00242 19 999-2118 20 999-1861 21 SPG-2001 DESCRIPTION NOTE
Marquee Glass 3/16” x 28.969” x 9.813” Fluorescent bulb 24” F20T12CW “Coolwhite” Leg Leveler 1/2-13 3” Caster 160-2 1/2 Swivel Seat Speaker 4” 60z. 80hm 25W Monitor Glass 3/16” x 28.875” x 22.688” Monitor Bezel Shifter Up/Down Cover Shifter Indy 500 Cover Shift B Fan 110/120 VAC 17/15W Sinwan Accel and Brake Assy. Vent Air 4 Hole Handle Collar Steering Wheel Bezel Vent Air 8 Hole Slide Seat Assy w/ Modified Handle Pushbutton Rect. VLT Blue View PSH BTTN SM VLT YEL RND Start Steering Wheel
Parts Not Indicated List
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | 999-1899 | Meter Coin 6VDC (6)digit w/diode |
| 2 | 999-1860 | Knob 1/4” Shaft 450-2023 |
| 3 | 601-11351 | SW Hub Melco LSW10/100-8H |
| 4 | 998-1222 | Pot 5K Ohm |
| 5 | 998-0676 | Switch On/Off Rocker |
| 6 | 999-2114 | Steering Wheel Bezel |
| 7 | 999-1177 | Cash Box |
| 8 | 600-7141-100 | Cable JVS Type A-B 100CM |
| 9 | 600-7247-500 | Cable SCSI ST-L Type2 500MM |
| 10 | 600-7269-0200 | Assy Lan Cable 200CM |
| ll | 999-0574 | Plate Leg Leveler |
| 12 | 999-2119 | Monitor Glass Retainer Bracket |
| 13 | 999-2120 | Rubber Mat Cabinet |
| 14 | 999-2121 | Rubber Seat Base Mat |
| 15 | 999-2122 | Rubber Seat Step Mat |
ASSY ACCEL&BRAKE (SPG-2200)
ASSY ACCEL&BRAKE (SPG-2200)
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | SPG-2201 | BASE |
| 2 | SPG-2202 | ACCEL PEDAL |
| 3 | SPG-2203 | BRAKE PEDAL. |
| 4 | SPG-2204 | ACCEL SPRING |
| 5 | SPG-2205 | BRAKE SPRING |
| 6 | SPG-2206 | SHAFT |
| 7 | SPG-2207 | ACCEL GEAR |
| 8 | SPG-2208 | BRAKE GEAR |
| 9 | SPG-2209 | NEUTRAL STOPPER |
| 10 | SPG-2210 | VR PLATE ACCEL |
| ll | SPG-2211 | VR PLATE BRAKE |
| 12 | SPG-2212 | AMPL GEAR |
| 13 | SPG-2213 | GEAR SHAFT |
| 14 | SPG-2214 | STOPPER |
| 15 | SPG-2215 | RUBBER CUSHION |
| 16 | SPG-2216 | COVER |
| 17 | SPG-2217 | VR COVER |
| 19 | SPG-2219 | GEAR STAY |
| 20 | SPG-2220 | WSHR |
| 21 | SPG-2221 | NEUTRAL STOPPER D |
| 101 | 100-5263 | BEARING 12(OILES 80F-1212) |
| 102 | 220-5484 | VOL CONT B-SK OHM |
| 104 | 601-7944 | GEAR 15 |
| 105 | 310-5029-F15 | SUMITUBE F FISMM |
| 106 | 280-0419 | HARNESS LUG |
| 201 | 028-A00304-P | SET SCR HEX SKT CUP P M3x4. |
| 202 | 020-000520-0Z | HEX SKT H CAP SCR BLK MSx20 |
| 203 | 000-P00420 | M SCR PH M4x20 |
| 204 | 000-P00508-W | M SCR PH W/FS M5x8 |
| 205 | 000-T00408-0C | M SCR TH CRM M4x8 |
| 206 | FAS-450005 | SPR PIN BLK OZ 6x10 |
| 207 | 000-P00405 | M SCR PH M4x5 |
| 208 | FAS-000001 | M SCR TH CRM M3x6 |
| 209 | 050-H00500 | HEX NUT MS |
| 210 | 060-F00400 | FLT WSHR M4 |
ASSY HANDLE MECHA (SPG-2500) D-1/2
&) OO,
ASSY HANDLE MECHA (SPG-2500) D-2/2
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | SPG-2501 | HANDLE BASE |
| 2 | SPG-2502 | BASE LID |
| 3 | SPG-2503 | HANDLE SHAFT |
| 4 | SPG-2504 | PULLEY 20 SSM |
| 5 | SPG-2505 | PULLEY 60 SSM |
| 6 | SPG-2506 | MOTOR BRKT |
| 7 | SPG-2507 | VR BRKT |
| 8 | SPG-2108 | STOPPER BOLT |
| 9 | SPG-2109 | STOPPER RUBBER |
| 10 | SPG-2453 | KEY 4%4x40 |
| 1 | ASK-3502 | MOTOR SPACER |
| 12 | ASK-3503 | MOTOR COLLAR |
| 13 | DYN-1270 | STOPPER KEY |
| 14 | SLC-1130 | ADJUST RING |
| 15 | SPG-2454 | MOTOR SHAFT COLLAR |
| 101 | 350-5448-01 | SERVO MOTOR 500W NEW |
| 102 | 100-5112 | BEARING 17 |
| 103 | 601-8966 | GEAR HOLDER |
| 104 | 601-6172 | GEAR 48 |
| 105 | 601-6959 | GEAR 64 |
| 106 | 601-9173 | TIMING BELT |
| 107 | 220-5484 | VOL CONT B-SK OHM |
220-5373 VOL CONT B-SK
| 108 | 310-5029-F20 | SUMITUBE F F 20MM |
| 201 | 028-A00408-P | SET SCR HEX SKT CUP P M4x8 |
| 202 | 028-A00308-P | SET SCR HEX SKT CUP P M3x8 |
| 203 | 065-S012S0-Z | STP RING BLK OZ S12 |
| 204 | 065-S020S0-Z | STP RING BLK OZ S20 |
| 205 | 000-P00408-W | M SCR PH W/FS M4x8 |
| 206 | 000-P00412-W | M SCR PH W/FS M4x12 |
| 207 | 030-000612-S | HEX BLT W/S M6x 12 |
| 208 | 060-F00600 | FLT WSHR M6 |
| 209 | 050-U00600 | U NUT M6 |
| 210 | 030-000840-S | HEX BLT W/S M840 |
| 211 | 068-852216 | FLT WSHR 8.5-22 1.6 |
| 212 | 050-U00800 | U NUT M8 |
| 301 | 600-6866 | WIRE HARN ASSY HANDLE MECHA VR |
ELECTRONICS LOWER
ITEM NO. PART NO.
1 838-13578 2 Local Purchase 3 998-0138 4 998-0218 5 Local Purchase
DESCRIPTION NOTE
Audio Power Amp 2ch. and Mixer 3A Slow Blow Fuse Isolation Transformer ER-503 Line Filter 5A Slow Blow Fuse
ELECTRONICS UPPER
ITEM NO. PART NO. DESCRIPTION NOTE
| 1 | 843-0005D-01 | Assy Case Box ORT USA | |
| 2 | XKT-0833 | Kit GDRom drive w/ Label | |
| 3 | 400-5443 | Power Supply | |
| 4 | 838-14174 | Servo Motor Drive BD. | Only first 50 Units |
| 5 | 610-0674 | Power Protetor Unit for Chihiro | |
| 6 | 837-13551-92 | V/O Control BD for JVS |
- WIRE COLOR CODE TABLE
THE WIRE COLOR CODE is as follow:
moaw> PINK
SKY BLUE
BROWN
PURPLE
LIGHT GREEN
Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.
CaordUNrRwnNne RED
BLUE
YELLOW
GREEN
WHITE
ORANGE
BLACK
GRAY
If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).
<Example> 51 ......... WHITE/ RED
RED WHITE
The character following the wire color code indicates the size of the wire.
U: AWGI16
Ky AWGI18
L: AWG20
None: AWG22
Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.
SEGA AMUSEMENTS USA, INC.
45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax