CATHODE RAY TOMES

Star Wars TM-225 2nd Printing

Star Wars (set 1) (Atari, 1983) · Technical Manual · 96 pages · 100 sections · original scan

Page 1

TM-225 2nd printing

©1983 Lucasfilm Ltd. & Atari, Inc. All rights reserved. “Trademarks of Lucasfilm Ltd. used by Atari, Inc. under license.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska, or Hawaii (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Ine. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey Ss (201) 469-5993 s From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts and Service

Atari ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28-165 TIPPERARY TOWN. (Monday-Friday, 9:00-6:00 pm GMT) IRELAND BH 0062-52155

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4

Star Wars

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, of otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringets are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment Of up to five years. Auri will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 8M

Page 5

Star Wars

Notice Regarding Non-ATARI Parts

Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts of supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits fora Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in acommercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All green ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. © The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

Star Wars

Table of Contents

Set Up How to Use This Manual Game Overview .... : 13 Installation Specifications . 13 Inspecting the Game 13 Voltage-Plug Selection and Fuses . 1-4 Flight Control Calibration . . . . 15, Switch Locations 15 Selecting the Game Options 16 Game Play 1-8 Attract Mode... . 18 Selecting-a-Death Star Mo le 19 Play Mode 1-10 High-Score Mode Vl Self-Test Mode . 1-i

Self Test Self-Test Displays .. 6... eee eee asscen 22

Troubleshooting Troubleshooting Aids Troubleshooting Techniques . .

Maintenance Cleaning Requirements Opening the Control Panel . Flight Control Maintenance . Removing the CRT Assembly .. Wiring the Utility Panel Controls... 2.2... 6 eee s+. 4:10

Illustrated Parts Lists Cabinet-Mounted Assemblies, US-Built Cabinet 5-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . .. 56 Star Wars Decals, US-Built Cabinet .........-.....- . . 5-10 Flight Control Assembly ......... . 512 Fluorescent Tube and Speaker Assembiy . 5-15 Utility Panel Assembly . . . - 5-16 Vertically Mounted Coin- Door . 518 American-Made Coin-Door . - 5-21 Power Supply Assembly .. . . 5-24 PCB Mounting Hardware, US- Built ‘Cabinet - . 5-26 PCB Mounting Hardware, Ireland-Built Cabinet - 5-28 EMI Shield PCB Assembly ............--- 7 : - 5-30 Regulator/Audio II PCB Assembly ............- fue . 5-32 Main PCB Assembly .............0-.00000- . 5-35 Analog Vector-Generator (AVG) PCB Assembly . wecwad - 5-40 Sound PCB Assembly .......0..00000 0000 e eee eee - 5-45 Glossary

Page 7

List of Illustrations

Figure 1-1 Figure 1-2 Figure 1-3

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 5-1A Figure 5-IB Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9A Figure 5-9B Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13 Figure 5-14

Table 1-1 Table 1-2 Table 1-3 Table 1-4 Table 2-1 Game Overview 1-2 Voltage-Selection Plug and Fuse Locations . 1-4 Switch Locations ......... 1-5

Accounting and Game Times Display 2-2 Game Options Display . 23 Hardware Errors Display—Test Passes . 23 Hardware Errors Display—Test Fails 23 Switch Test Display . 2-5 Mathbox Tests Display—Test Passes 2-5 Mathbox ‘Tests Display—Test Fails 25 Crosshatch Pattern Display . . 2-6 Grid Pattern Display. ...... : 2-6 Intensity Test Display ......... 2-7 Bipolar Offset Test Display—Test Passes 2-7 Bipolar Offset Test Display—Test Fails . 27 Scale Test Linear Display ........ 2-8 Scale Test Linear and Binary Display : peso ee 2-8 Raster Screen Display ............- . 28

Handle Assembly . Steering Assembly . Removing the CRT Assembly Utility Panel Wire Colors .....

Illustrated Parts Lists

Cabinet-Mounted Assemblies, US-Built Cabinet .... 5-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . 5-6 Star Wars Decals ............... 5-10 Flight Control Assembly......... 5-12 Fluorescent Tube and Speaker Assembly veces : 5-15 Utility Panel Assembly 5-16 Vertically Mounted Coin-Door . . 5-18 American-Made Coin-Door 5-21 Power Supply Assembly 5-24 PCB Mounting Hardware, US-Built Cabinet . . 5-26 PCB Mounting Hardware, Ireland-Built Cabinet . - 5-28 EMI Shield PCB Assembly - 530 Regulator/Audio II PCB Assembly 5-32 Main PCB Assembly - 5-35 Analog Vector-Generator (AVG) PCB Assembly . Sound PCB Assembly

List of Tables

Installation Requirements Switch Settings for Play Options . : Switch Settings for Coin and Credit Options. : Switch-Settings for Special Options : Main and AVG PCB Faulty RAM & ROM Locations . . © 5-45 Star Wars

Page 8

Star Wars

vi

Safety Summary

The following safety precautions apply to all game Operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNINGS A

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is instalied on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end ofa large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the impiosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do notslip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators andservice technicians, describes your new Atari game. Wherever information is unique to the Ireland-built game, this symbol

appears: x

Wherever informati symbol appears: is unique to the US-built game, this

Chapter | contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains troubleshooting procedures. Chapter 4 contains maintenance and repair procedures, Chapter 5 contains illustrated parts lists, Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a supplement to this manual.

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area. Do not touch internal parts of the display with your hands or metal objects!

Chapter 1

Page 10

Setup

Fluorescent Tube & Speaker See Figure 5-4

Flight Control Assembly, See Figure 5-3

Control Panel

Utility Panel Assy. See Figure 5-5

High-Voltage PCB x Used with Atari Display See Display Manual Star Wars

Game Identification Label x

fs ™

Access Panel

Deftection PCB x Used with Atari Display ° See Display Manual

EM! Cage See Figure 5-94, PCB Housing See Figure 5.9B

Inside EMI Cage & PCB Housing Main PCB See Figure 5-12 AVG PCB x See Figure 5-13 SoundPCB* See Figure 5-14

‘EMI Shield PCB See Figures 5-9 & 5-11 Regulator/Audio Il PCB + See Figures 5-9 & 5-10

Power Supply * See Figure 5-8 enter ORION Swtchi

WARNING

Shock Hazard

Do not plug in the game until it has been inspected. This game should only be connected to a grounded S.wire outlet. Ifyou have onlya 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Coin Door Assy. See Figures 5-6 or 57

  • Item with a serial number label

Figure 1-1 Game Overview

1-2

Page 11

Star Wars

Game Overview

STAR WARS* is a spectacular video spectacle! STAR WARS is a one-player game, which uses a color XY video display. As the player, you'll enter the exciting world of LUKE SKY WALKER’ and pilot the RED 5 X-WING* spacecraft to victory over the Empire's evil forces!

New Features Voice-enhanced game play. The voices you will recognize belong to the actual characters of LUKE SKYWALKER, DARTH VADER’, BEN KENOBI", HAN SOLO*, and R2-D2*. They intensify the excitement of swift and dynamic game play. Flight control. The flight control for STAR WARS is a new Atari design. it allows a player to use real flying techniques on. a voyage that is out of this world!

‘Tamper-proof screws. Tamper-proof screws on the cover of the flight control assembly prevent abuse of the control or its handles. Flight-control wrench. special wrench for the tamperproof screws is included with your game. It is located in the coin box. Medium-speed, medium-resolution, cathode-ray tube. This new XY cathode-ray tube (CRT) produces exceptionally clear graphics for the world of LUKE SKYWALKER.

Options display. The Self-Test program of STAR WaRs includes an options display that enables you to select game options without having to set the option switches from the back of the cabinet. See Chapter 2 for more details.

All major parts of the sTAR wars cabinet are illustrated in Figure 1-1.

Installation Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Requirements

Characteristic Requirement

Power Consumption 250 W Nominal Temperature O° to +38° C(+32° to +100° F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC Width 64.1 cm (25.25 in.) Depth 83.2 cm (32.75 in.) Height 182.9cm (72 in.)

*© 1983 Lucasfilm Ltd. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. Set-Up

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCBare firmly plugged into their sockets. c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Inspect the power supply. Make sure the fuse block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, EMI cage, and each PCB. Make sure they are mounted securely and that the green ground wires are connected.
Page 12

Set-Up

Voltage-Plug Selection

and Fuses

The power supply in your game conuins six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire

FUSE F2: 4A, 250V

20A, 32V

FUSES F4-F6 4A, 250V Star Wars

colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voitage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

VOLTAGE-SELECTION PLUGS

7A, 250V

J3

Fuse cover is shown in Figure 5-8

Figure 1-2 Voltage-Selection Plug and Fuse Locations

Page 13

Star Wars

Flight Control Calibration

The STAR WARS game has a seif-calibrating flight control. The game circuitry monitors the position of the cursor on the display in relation to the flight control vertical and horizontal position. Calibration is quickly accomplished by moving the cursor to all four extreme edges of the display. Calibrating is also accomplished during normal game play, but may take a few seconds to optimize.

Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-2).

Utility Panel Switches The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel js located inside the upper coin door (see Figure 1-1). Set-Up

The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. Sce Figures 1-3 and 5-5 for details of these switches.

Option Switches STAR WARS has three option switches. These switches are dual-inline package (DIP) switches located on the Main PCB. The Main PCB is set in the electromagnetic interference (EMI) cage (see Figure 5-9.) Figure 1-3 shows the location of these switches on the Main PCB: © The option switch at 10D is for selecting play options. ® The option switch at 10E/F is for selecting coin and credit options.

  • The option switch at UL is for selecting special options.

Coin Volume

Counter Control

Auxiliary Coin Switch

vty ree om Sound Board Game PCB Switch

Interconnect q Board

L m O on { OFF C on C

10E/F CI I roo C1) ot

I

Figure 1-3 Switch Locations

Page 14

Set-Up

Selecting the Game Options

Settings for option switches are listed in Tables 1-2, 1-3, and 1-4. Options preset at the factory are shown by the < symbol; however, you may change the settings according to your needs,

To verify other option selections, check the self-test display that appears when you turn on the game. Then, verify the option-switch settings on the self-test display as described in Chapter 2.

Important: The Self-Test program of STAR wars includes an options display that enables you to select game options without having to set the option switches from the back of the cabinet. See Chapter 2 for more details. Star Wars

Table 1-2 lists settings for the DIP switch at 10D. This switch is used to select play options (such as the number of starting shields per game). Table 1-3 lists settings for the DiP switch at 10E/E. This switch is used to select coin and credit options available for the left and right coin mechanisms. Table 1-4 lists settings for the DIP switch at LIL. This switch is used to select a special option for the way coin outputs are handled by the game. The basic unit of measurement is a coin worth $.25 or 1 DM. Thus, if you have a2 DM/1 DM coin door with two coin counters, set switch | at location 11}. to OFF, Then, different denominations are counted on the two coin counters.

Table 1-2 Switch Settings for Play Options

Settings of 8Toggle Switch on Star Wars Game PCB (at 10D) 1 2 6 7 3 4 5 8 Option

On On Off on On Off

Off Off

On On Off = On On Off

On On

Off On

On Off off Off

On Off 6 Starting Shields-<4 7 Starting Shields 8 Starting Shields 9 Starting Shields

Easy game play Moderate game play Hard game play 4 Hardest game play

0 Bonus Shields for Destroying Death Star 1 Bonus Shield for Destroying Death Star<4 2 Bonus Shields for Destroying Death Star 3 Bonus Shields for Destroying Death Star

Music in the Attract Mode No Music in the Attract Mode

On Freeze Mode Off Normal Game Play Mode<4

4Manufacturer’s recommended settings

1-6

Page 15

Star Wars Set-Up

Table 1-3 Switch Settings for Coin and Credit Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10E/F)

12345678Option
OnOnFree Play

Off On 2 Credits Off Off Ye Credit

OnOff1 Credit<4

Left Coin Mechanism On 1 Coin Off 2 Coins Right Coin Mechanism On On 1 Coin

Off On 4 Coins

On Off 5 Coins

Off Off 6 Coins

Bonus Coin Adder

OnOnOn0 Bonus Coins Added<4
OffOnOn1 Bonus Coin Added for 2 Coins
OnOffOn1 Bonus Coin Added for 4 Coins
OffOffOn2 Bonus Coins Added for 4 Coins
OnOnOff1 Bonus Coin Added for 5 Coins
OffOnOff! Bonus Coin Added for 3 Coins
OnOffOff0 Bonus Coins Added
OffOffOff0 Bonus Coins Added

Table 1-4 Switch Settings for Special Options

Settings of 4-Toggle Switch on Star Wars Game PCB (at IIL) nN we Option

On z Fa ra Outputs of coin counter driver 1 and 2 tied together

e c (for 1 counter) <4

Offé88Outputs of coin counter driver 1 and 2 separate (for 2
SaScounters)

4 Manufacturer's recommended settings

Page 16

Set-Up

Game Play play. You command LUKESKY WALKER's RED 5-XWING space

STAR WARS is a One-player game with a color X¥ video display. You command LUKESKY WALKER's RED 5-XWING spacecraft with Atari's new flight control. Your main goal is to blow up the DEATH STAR*. To do this, you must reach the thermai exhaust port at the end of the DEATH STAR trench, and fire a proton torpedo into it. You must survive three phases of play to reach the exhaust pott. The first phase of play will engage you in a spectacular battle in space—a war in the stars! TWIN-ION ENGINE (TLE,) FIGHTERS* from the DEATH STAR attack you. DARTH VADER’s ship appears in this phase—menacing and powerful! Your goal in this phase is to shoot the T.LE. FIGHTERS and their shots.

The second phase of play takes the X.WING down to the surface of the DEATH STAR which is covered with laser bunkers and laser towers. You must avoid collision with these objects and their shots to keep the number of Deflector Shields above zero. Extra bonus points are earned for exploding all laser tower tops. The third phase of play takes RED 5 down into the DEATH STAR trench. The walls are lined with red Iaser-gun turrets that fire at you as you approach. You must counter these shots by avoiding them or by shooting them. Trench catwalks also appear, in varied shapes and altitudes. You must avoid hitting the catwalks, or else your number of deflector shields will decrease.

If you survive the flight down the trench, a message and voice will alert you that the exhaust portis straight ahead. You must shoot the exhaust port to explode the DEATH sTaR. If you miss the exhaust port, you will plough through the wall at the end of the trench and lose one deflector shield If you succeed in blowing up the DEATH STAR, RED 5 soars away from the DEATH STAR and then turns to view the tremendous explosion. Select-a-Death Star bonus and Remaining Shield Energy bonus are now scored. Depending, on the settings of the option switches (see Tables 1-2, 1-3, and 1-4), additional deflector shields will be awarded. A new DEATH STAR then comes into view. The EMPIRE* is really mad now, and the powers in the EMPIRE want to launch LUKE and the RED 5 into eternity! STAR WARS has five possible modes of operation: Attract, Select-a-Death Star, Play, High Score, and Self-Test

  • ©1983 Lucasfilm Lid. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. Star Wars

Attract Mode

The Attract Mode begins when power is applied to the game; or when the Play, High-Score, or Self‘Test Modes end, The Attract Mode ends either when a credit is entered and the game goes into Selecta-Death Star Mode, or when, the self-test switch is turned on. The first screen displayed in the Attract Mode is the Banner Screen. The SZAR WARS logo appears with a background of moving stars and then flies away to infinity. As it vanishes, the introductory story line moves into position from the bottom of the screen. The text pauses for about 20 seconds and then, one line at a time, quickly recedes into the distance.

Banner Screen Text:

OBI-WAN KENOBI IS GONE BUT HIS

PRESENCE IS FELT WITHIN THE FORCE. THE EMPIRE'S DEATH STAR UNDER THE COMMAND OF DARTH VADER NEARS THE REBEL PLANET, YOU MUST JOIN THE REBELLION TO STOP THE EMPIRE. THE FORCE WILL BE WITH YOU. ALWAYS. The next screen in the Attract Mode is the Flight Instruction Screen. It outlines RED 5’s weaponry, defense system, and mission. The text appears one line ata time, pauses for about 20 seconds, then fades away. Flight lastruction Screen FLIGHT INSTRUCTIONS TO RED FIVE 1, YOUR X-WING IS EQUIPPED WITH AN INVISIBLE DEFLECTOR SHIELD THAT WILL PROTECT YOU FOR x** COLLISIONS. 2, DEFLECTOR STRENGTH IS LOST WHEN A FIREBALL IMPACTS YOUR SHIELD OR WHEN YOU STRIKE A LASER TOWER OR TRENCH CATWALK.

  • AIM YOUR LASERS WITH CURSOR TO EXPLODE EM- PIRE TIE FIGHTERS, LASER TOWER TOPS AND TRENCH TURRETS.
  • SHOOT FIREBALLS BEFORE THEY IMPACT YOUR SHIELD. 5, THE REBEL FORCE IS DEPENDING ON YOU TO STOP THE EMPIRE BY BLOWING UP THE DEATH STAR. The top part of the Banner Screen should display the last score achieved and the wave number. The messages /N- SERT COINS) and X COINS PER PLAY should alternately flash if no credit is in the game. If the game has credits, then the message X CREDITS and PULL FIRE TRIGGER TO START will be displayed. These messages appear on all screens. The third screen in the Attract Mode is the Scoring Screen. It lists targets in the game and their point values. This screen scrolls up from the bottom of the screen then fades away. ** Replace x with 6, 7, 8, or 9, depending on option switch settings.
Page 17

Star Wars

Scoring Screen SCORING TIE FIGHTERS 1,000 DARTH VADER SHIP 2,000 LASER BUNKERS 200 LASER TOWERS 200 TRENCH TURRETS 100 FIREBALLS 33 EXHAUST PORT 25,000 DESTROYING ALL TOWER TOPS 50,000 The fourth screen in the Attract Mode is the High-Score Screen. It displays a table containing the ten highest scores. At the bottom of the screen the copyright message appears. (The High-Score Screen shown here contains the default entries that will appear if no high scores are in the game’s memory.) The game will retain and display the top three scores entered into its memory even if the power is turned off and then on again. SetUp

High-Score Screen PRINCESS LEIA’S REBEL FORCE

LOBI1285353
2,WAN1110936
3.HAN1024650
4,GR872551
5.MLH813553
6.JED704899
7.NLA518000
8.EJD492159
9.EAR384766
10.RIM380655

STAR WARS © 1983 LUCASFILM LTD, AND ATARI, INC. ALL RIGHTS RESERVED LUCASFILM TRADEMARKS USED UNDER LICENSE. You may bring the High-Score Screen or the Flight Instruction Screen into view at any time during the Attract Mode. Moving the flight control to the right displays the High- Score Screen and moving it to the left displays the Flight Intruction Screen.

Select-a-Death Star Mode

The Select-a-Death Star Mode begins when the correct credit(s) is entered anda fire trigger is pulled. You will hear the voice of LUKE saying, “RED 5 standing by,” and you'll have 8 seconds to select one of 3 starting DEATH STARS. A DEATH STAR is selected by first maneuvering the flight control until the cursor on the screen is positioned on the desired DEATH STAR and then by pulling the Laser Fire Trigger. The DEATH STARS are labeled easy, medium, and hard on the display. The Easy DEATH sTaR awards no bonus for completion of the starting level as indicated by NO BONUS. The Medium DEATH STAR awards 400,000 points and the Hard DEATH STAR awards 800,000 points. Failure to select a level within the countdown time automatically starts the Play Mode at the Easy level (wave one),

Page 18

Setup

Play Mode

STAR WARS game play is enhanced by 13 special sound effects and by actual character voices communicating with the player. Voices:

LUKE: RED 5 standing by. LUKE: R2, try and increase the power, LUKE: This is RED 5, I'm going in. LUKE: I'm hit but not bad, R2 see what you can do with it. LUKE: I've lost R2. LUKE. I can't shake him! DARTH I’m on the leader. DARTH: The FORCE is strong with this one. DARTH Thave you now! DARTH. Stay in attack formation. BEN: Use the FORCE, LUKE. BEN: Remember, the FORCE will be with you, always. BEN LUKE, trust me. BEN: Let go, LUKE. HAN Yahoo! You're all clear, kid. HAN: Great shot kid! That was one in a million. WEDGE* Look at the size of that thing! R2: Yes. R2: No. R2: agree. R2: Sequence completion. R2: Ouch! R2: That really hurt. The Play Mode begins in outer space with the DEATH STAR Off in the distance. The RED 5 X-WING aiming device (cursor) appears as a crosshair on the screen. As the flight control is moved in any direction, the four laser guns move accordingly. Firing the laser guns will cause alternating laser beams to fire from the guns toward the cursor. in this mode, k2-D2 is controlling the flight pattern of the XWING based on the flight of attacking TLE. FIGHTERS.

Your goal is to blast any and all 7.1.£. FIGHTERS and their oncoming shots. If youare hit, your deflector shield will automatically turn on and dissipate the energy from the shot, causing a very bright light to flash on the screen. You will experience a roll in space due to the impact. In a while, the T.LE. FIGHTERS will turn away from you and fly back to the DEATH STAR.

“© 1983 Lucasfilm Ltd. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license.

1:10 Star Wars

In the next phase of the Play Mode, the x-WING flies directly toward the DEATH STAR, engines roaring, to a surface covered with hostile laser bunkers and laser towers. Now you, Not R2-D2, control the x:wING. Your goal in this phase is to reach the trench. To do this you must avoid or eliminate (by shooting) the structures and the shots fired by them. The laser tower tops have a progressive scoring incentive that is displayed in a message in the top center of the screen, along with the number of remaining laser tower tops to be destroyed before the x-wING dips into the trench. Eliminating all laser tower tops awards you an added bonus. Getting hit by ashot or smashing into a laser tower top or laser bunker will roll the X-WiNG to the right or left as the deflector shield automatically turns on and absorbs impact, displaying a very bright screen. Each collision costs you one deflector shield.

Once you have traveled the required distance over the DEATH STAR Surface, the X.WING dips down into the long, deadly trench. In this phase, you can fly right, left, up, or down; but you remain within the trench. Your main goal while in the trench is to destroy the DEATH STAR by shooting the exhaust port at the end of the trench. You can survive the trench by flying around catwalks, which stretch across the trench at various altitudes, and by avoiding or shooting shots fired from the red laser-gun turrets on the walls, Deflector shield energy is lost ifa shot hits you or if you smash into a catwalk. If you successfully reach and shoot the exhaust port, the RED 5 X:WING will soar away from the DEATH STAR and then turn toward it to watch it blow up. If you miss the exhaust port, you will crash through the back wall and R2-p2 will show his displeasure with you. The X.wiNG will remain in the trench until the DEATH STAR is destroyed or you run out of deflector shields. Upon destroying the DEATH STAR, the X-WING returns to another war in the stars with smarter TE. FIGHTERS from a more advanced DEATH Star. Your ability as a JEDI WARRIOR* will be challenged even more with the destruction of each successive DEATH STAR.

Page 19

Star Wars

Hints for Game Play © Develop skill for controlling the XWING with the flight control. It’s like flying a plane. © Blastall the laser tower tops with your laser guns for additional bonus points. © STAR WARS is a pattern game, so learn the easy levels, and then select a more difficult level. © The game requires almost constant laser fire during higher levels. The game ends when you get hit and the deflector shield level is zero. The words GAME OVER appear in a very large size as your ship vanishes from the screen.

High-Score Mode

This mode begins with lively music if your score is one of the ten highest scores earned since the game was turned on. A screen appears with the message:

MESSAGE FROM REBEL COMMAND POST YOU ARE A TRUE REBEL PILOT THE FORCE IS WITH YOU SHOOT YOUR INITIALS

Initials surround the high-score table in the middle of the screen, You have 30 seconds to shoot (enter) your initials. The top 3 scores will be saved even with the power off, but the entire high-score table can be reset to its default scores when in the Self-Test Mode. SerUp

Self-Test Mode

SeifTest is divided into two sections. The first section shows game Statistics and allows the operator to reset certain statistics or change options with the use of the flight control. The second section is designed to allow checking of game switches, hardware failures, potentiometer adjustments, and video display adjustments. SelfTest may be entered any time during the Attract Mode. See Chapter 2 for details.

Vl

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 22

Self-Test

Self-Test Displays

Fourteen self-test displays provide a visual check of the game statistics, options, switch settings, mathbox circuitry, display circuitry, and the condition of the read-only memory (ROM) and random-access memory (RAM). The first self-test display (Size and Centering) is obtained while in the Attract Mode. When the self-test switch is turned on during the Attract Mode, the game enters the Self-Test Mode. Turning the self-test switch off at any time during the Self‘Test Mode causes the game to return to the Attract Mode.

NOTE Before selecting the Self-Test Mode, perform the following size and centering check with the game in the Attract Mode. The remaining self-test displays are obtained while the game is in the Self-Test Mode.

Size and Centering Display

While the game is in the Attract Mode, verify that a small blue dot is displayed within %-inch of the edge in each corner of the screen. If the blue dots are not in the proper position, refer to the X/Y size and centering adjustment procedures included on the Analog Vector-Generator schematic diagrams.

NOTE The following self-test displays are arranged in the sequence in which they occur after the selftest switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. If the self-test procedures are not performed in sequence, pressing the auxiliary coin switch will advance through the displays until the desired display is obtained. After the last display has ended, the sequence starts over with the Switch Test display. To start with the Accounting and Game Times display, the self-test switch must first be turned off and then on again.

Accounting and Game Times Display

Select the Self-Test Mode by pushing the self-test switch to the up position. The Accounting and Game Times display will appear as shown in Figure 2-1. The totals on this display are those accumulated since the accounting and game times information was last reset. (Refer to Game Options Display for the reset procedure.) The coin accounting information, which is the first four statistics in the Account. ing Information section of the display, cannot be reset. They are accumulated from the date the game was manufactured, or since the non-volatile random-access memory {NOVRAM) last failed or was replaced. Star Wars

@CCOUNTING INFORMATION

HISTORY OF GAME meee ou a n o (

a 2.

Figure 2-1 Accounting and Game

Times Display

AUXILIARY COINS displays the number of free credits selected by the auxiliary coin switch in the normal play mode. LEFT MECH COINS displays the number of coins inserted into the left coin mechanism. RIGHT MECH COINS displays the number of coins inserted into the right coin mechanism. TOTAL COINS PAID displays the total number of coins inserted into both game coin mechanisms.

NOTE The following accounting and time information is accumulated since the game was manufactured (or last reset). Refer to Game Options Display for the reset procedure.

GAMES PLAYED displays the total number of free and paid games played and highest wave achieved. TOTAL GAME TIME displays the total time, in seconds, of all the games played. AVERAGE GAME TIME displays the average time, in minutes and seconds, of all the games played. TOTAL TIME ON displays the total time, in seconds, the game has been on. PERCENTAGE OF PLAY displays the percentage of time the game has been in Play Mode (as opposed to Attract Mode). HISTORY OF GAME TIMES displays the number of games played that were within each of 18 game-time increments (0 to six minutes in 20- second increments).

Page 23

Star Wars

Game Options Display

Press the auxiliary coin switch to obtain the Game Options display as shown in Figure 2-2. Use this display to view or change game option settings; reset high scores; reset accounting and game time information; or test the NOVRAM.

mane OFT IONS vacue OF @ CEN

STARTING PLAY DIFF BONUS SHIELD MUSIC IN ATTRACT

RESET HIGH SCORES RESET TIMING INFO RESET DFTIONS TEST NOVRAM

FULL RIGHT FIRE TO PERFORM um, DOWN TO SELECT ITEM Pu LEFT FIRE TO CHANRE SETTING

PRESS QUX COIN FOR SELF TEST

Figure 2-2 Game Options Display The first section of the Game Options display shows the option settings that have been selected by either the option switches on the Main printed-circuit board (PCB) or by the flight control. The second section of the Game Options display shows the reset and NOVRAM test operations that are selectable with the flight control. Press the auxiliary coin switch to end this display. Changing the Game Options. Any of the options displayed in the first section of the Game Options display can be changed without setting the option switches on the Main PCB. Select the option to be changed by moving the flight control up or down. Press the left-hand fire trigger to cycle through the available options as indicated in the righthand column; stop on the desired option setting. The changed option is immediately stored in the NOVRAM and is unaffected by turning off the power or the self-test switch. The options can also be changed to those selected by the option switches located on the Main PCB (see Chapter 1). If the self-test circuitry malfunctions or the option settings cannot be maintained by the software, the game will default to the hardware switch settings on the Main PCB (refer to Resetting the Options for more details). Resetting the High Scores. The top ten scores and player initials are displayed in the high-score table during the Attract Mode. All high scores can be reset using the Game Options display. Select RESET HIGH SCORES by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Selflest

Resetting the Timing Information. The games played and the timing information in the Accounting and Game Times display (see Figure 2-1) can be reset using the Game Options display. Select RESET TIMING INFO by moving the flight control up or down. Press the left-hand fire trigger and

note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Resetting the Options. The option settings shown on the Game Options display (see Figure 2-1) can be reset (defaulted) to those selected by the option switches located on the Main PCB. Select RESET OPTIONS by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column. Then press the right-hand. fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Testing the NOVRAM. The NOVRAM can be tested using, the Game Options display. Select TEST NOVRAM by moving the flight control up or down. Press the left-hand trigger and check that VO ERRORS appears in the right-hand column. If the NOVRAM is defective, a message ERROR AT and a hexadecimal number will appear, which indicates that the NOVRAM should be replaced. Testing the NOVRAM should only be performed if a defective part is suspected because each test decreases the life of the NOVRAM.

23,

Page 24

Self-Test

Hardware Errors Display Press the auxiliary coin switch and wait about seven seconds to obtain the Hardware Errors display as shown in Figure 2-3. This display shows the condition of the game RAMand ROM. If no hardware errors exist, the message NO ERRORS DETECTED will be displayed. If there is a RAM or ROM failure, the display will identify the failed component and give its location. See Table 2-1 to determine on which PCB the failed component is located.

NO ERRORS DETECTED

PRESS 9ux COIN TO CONTINUE

Figure 2-3 Hardware Errors

Display—Test Passes

BROGREM ROMA AT PRogREM ROM) AT PROGRAM ROME aT PROGRAM ROMS aT PROGRAM ROMY AT ARESS AUX COIN TO CONTINUE

Figure 2-4 Hardwate Errors

Display—Test Fails

A series of 16 tones will be heard after the Hardware Errors display appears. These tones provide an audible indication of the condition of the program RAM and analog-vector generator that can also be used to locate a faulty RAM or ROM if the display is inoperative or not visible. The series of tones, separated by a short pause, will repeat indefinite-

2-4 Star Wars

ly. Ahigh upward-sweeping tone indicates a properly operating RAM or ROM while a downward-sweeping tone indicatesa faulty RAM or ROM. Count the tones to determine the location of the faulty RAM or ROM as shown in Table 24.

Table 2-1 Main and AVG PCB Faulty RAM and ROM Locations

Tone Location Description

12F/H(Main)Program RAM
2SF (Main)Matrix Processor RAMO
35H (Main)Matrix Processor RAM 1
43L (AVG)Vector RAM 0
53M (AVG)Vector RAM 1
63P (AVG)Vector RAM 2
74L (AVG)Vector RAM 3
84M(AVG)Vector RAM 4
94P (AVG)Vector RAM 5
10JE (Main)Non-Volatile RAM (RAM.

portion only)

nh1F (Main)Program ROM 0
21HJ (Main)Program ROM 1

B IK (Main) — Program ROM 2

141K/L (Main)Program ROM 3
151M(Main)Program ROM 4
161L (AVG)Vector ROM

Switch Test Display

Press the auxiliary coin switch to obtain the Switch Test display shown in Figure 2-5. Perform the following procedure to verify that game switches are operating properly:

  • Oneata time, press the fire triggers and thumb pushbuttons. Note that a message appears on the display that indicates which switch was pressed.
  • Actuate the right and left coin mechanisms and note that a message appears that indicates which coin mechanism was actuated.
NOTE

When a game switch is actuated, an upwardsweeping tone occurs which provides an audible indication that can also be used to verify switch operation if the display is inoperative or not visible. However, the tone test does not indicate which switch is actuated.

Page 25

Star Wars

  • Position the flight control to form a single dot in the center of the smallest box in the POT TEST portion of the display.
  • Carefully release the flight control and note that the dot remains centered within the smallest box. Ifa line forms that extends outside the frame of the smallest box, the flight control potentiometers may be misaligned. Refer to Aligning the Potentiometers in Chapter 4 for alignment procedures.
  • Tiltthe flight control handles forward and backward;
note that a line forms from the center of the smallest box and moves outand back in relation to the handle position. Tilt the handles to the extreme forward and backward position; note that the line extends past the frame of the box with open corners but not beyond the frame of the largest box.
  • Turn the flight control fully clockwise and counterclockwise with the handles at the extreme forward then backward positions. Note that the line travels over a full 360° while not extending outside the area between the largest box and the box with the open corners.
  • Verity that the option settings for the switches at location 10D and 10E/F shown at the bottom center of the display match those selected on the corresponding option switches (F=off, N=on).

Lerr N RIGHT COIN

}OD FEENENNE DEF NENNNNNN PRESS eux COIN TH CONTINUE

Figure 2-5 Switch Test Display

Mathbox Tests Display

Press the auxiliary coin switch to obtain the Mathbox Tests display shown in Figures 2-6 and 2-7. The first test verifies that the MATHBOX READY signal is operating normally. If itis not, the message BAD MATHBOX READY LINE appears and no further mathbox tests are performed. If the Self-Test

MATHBOX READY signal is correct, then the divider and matrix circuitry should be tested. If no problems exist in the divider or matrix circuitry, the messages NO DIVIDER ERRORS and NO MATRIX ERRORS are displayed. If divider errors exist, the message DIVIDER ERRORS will appear and each error will be indicated with an optionswitch setting for the corresponding diagnostic. Also, the numbers used on the test with the expected answer and the incorrect answer received will be displayed for each test in error.

NO DIVIDER ERRORS

Figure 2-6 Mathbox Test Display— Test Passes

BAD MATHBOX READY LINE

Figure 2-7 Mathbox Test Display— Test Fails

If matrix errors exist, the message MATRIX ERRORS will appear with the corresponding option switch settings for the diagnostic. Some matrix errors do not have a corresponding diagnostic. In this case, there will be no option switch setting.

Page 26

Self-Test

Crosshatch Pattern Display Press the auxiliary coin switch to obtain the Crosshatch Pattern display as shown in Figure 2-8. Verify the following display characteristics:

  • Corners are closed and the diagonal lines form symmetrical diamond-shaped squares.
  • All four corners of the border are completely visible and are within %-inch from the black edge of the screen.
  • Pattern is not tilted more than 44-inch between corners. ° Pattern is auniform green color.

Figure 2-8 Crosshatch Pattern Display

If any of the preceding characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector- Generator schematic diagrams. Star Wars

Grid Pattern Display Press the auxiliary coin switch to obtain a Grid Pattern display as shown in Figure 2-9, Verify that the following grid colors can be obtained, in order, by pressing either fire trigger: Red Green Blue Purple White Yellow Turquoise

Figure 2-9 Grid Pattern Display

Verify the following display characteristics: © Grid lines do not exhibit pincushioning or barreling and the lines are straight within %-inch.

  • Convergence shall not exceed 2.0 mm, as checked with the white grid. Ifany of the preceding display characteristics are not cortect, refer to the linearity adjustment procedure in the Analog Vector-Generator schematic diagrams and to the convergence adjustment procedure in the Display Manual.
Page 27

Star Wars

Intensity Test Display

Press the auxiliary coin switch to obtain the Intensity Test display as shown in Figure 2-10. Verify the following display characteristics: © Top row of color bars are red, blue, and green. e Allthree sets of color bars have six lines with the same intensity. © Bars underneath the top row of color bars are white. © — Bars underneath the white color are yellow, turquoise, and purple. ° DIM, LOW, and HIGH appear in the bottom center of the display. If the word OFF can be seen, the display is too bright. If the word LOW cannot be seen, the display is not bright enough.

INTENSITY TEST

Figure 2-10 Intensity Test Display

if the preceding display characteristics are not correct, refer to the Display Manual for the brightness adjustment procedure or to determine the possible cause of failure. Self-Test

Bipolar Offset Test Display Press the auxiliary coin switch to obtain the Bipolar Offset Test TEST display as shown in Figures 2-11 and 2-12 The line width should be 4-inch or less. If not, adjust the X/Y bipolar offset potentiometers located in the digital-toanalog converter and bipolar current sources circuit on the Analog Vector-Generator PCB.

BIP TEET

ALIGN THE Boxee

Figure 2-11 Bipolar Offset Test

Display—Test Passes

Figure 2-12 Bipolar Offset Test Display—Test Fails

Page 28

Self-Test

Scale Test Display

Press the auxiliary coin switch to obtain the Scale Test Linear display as shown in Figure 2-13. A large green square should appear in the center of the screen and then smoothly shrink to a point. Next, a large green SCALE TEST LINEAR AND BINARY square appears and shrinks smoothly, then pauses and continues to shrink. There should be eight pauses before the square shrinks toa point. After each pause and just when the square begins to shrink,

the size of the square should not change appreciably. If a

large change in the size of the square occurs, an error may exist. After the eighth pause, the sequence repeats with the Scale Test Linear and Binary display as shown in Figure 2-14

~— OO SCALE TEST LINEAR

Figure 2-13 Scale Test Linear Display

SCALE TEST LINEAR AND BINARY

L_]

Figure 2-14 Scale Test Linear and Binary Display Star Wars

Raster Screen Display Press the auxiliary coin switch to obtain the Raster Screen display as shown in Figure 2-14. This display is the last of the self-test displays and is used by the manufacturer to adjust the white tracking of the display circuitry.

Figure 2-15 Raster Screen Display

NOTE Pressing the auxiliary coin switch to end the preceding Raster Screen display will repeat the self-test sequence starting with the Switch Test display. If desired, turn the self-test switch off, then on again, to obtain the Accounting and Game Times display.
Page 29

Troubleshooting

This chapter contains a discussion of troubleshooting aids and techniques to assist the service technician when a trouble is suspected in this game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your nearest Atari Customer Service office listed on the inside front cover of this manual for assistance.

A thorough knowledge of game operation is desirable for effective troubleshooting. In addition to the operation and service information in the Schematic Package Supplement included with this manual, refer to The Book, A Guide To Electronic Game Operation and Servicing, available from Atari, Inc., for more information on coin-operated electronic games.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified electronic technician.

Chapter 3

Page 30

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the Schematic Package Supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information,

Assembly and Component Locations

The illustrated parts lists in Chapter 5 illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components contained on the corresponding schematic diagram(s).

Schematic Diagrams Complete schematic diagrams are provided in the Schematic Package Supplement. Component designationsand their electrical values are included on the schematic diagrams. Memory maps are also included in the Schematic Package Supplement. Block diagrams of the major Circuits on the game PCB (with sheet numbers to aid in locating the appropriate schematic diagrams) are included in the Schematic Package Supplement.

Troubleshooting Procedures

This game will test itself and provide data to aid in localizing troubles toa major circuit. Self-test procedures are provided in Chapter 2. Refer to the following section on Troubleshooting Techniques for a suggested troubleshooting sequence that uses the self-test procedures. Detailed troubleshooting procedures for locating defective components are provided in the Troubleshooting Guide included in the Schematic Package Supplement. These procedures use hardware diagnostic tests and the Atari CAT Box to troubleshoot the game PCB.

Troubleshooting Techniques

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the trouble to an assembly or major circuit, and then to a defective component.

Check Switch Settings Incorrect switch settings can sometimes indicate a problem that does not exist. Refer to Chapter 1 Set-Up, to verify that the game has been installed properly and that the switches are set to their correct positions. Check for proper operation in all game-play modes.

Check Fuses Check for open fuses. Refer to che Power Supply Assembly Parts List in Chapter 5, Illustrated Parts Lists, and to the

3-2 Star Wars

Display Manual, for the location and rating of each fuse

used in this game. Make sure that replacement fuses are the

proper type and rating.

Check Power-Supply Voltages

Improper operation of all circuits usually indicates a power supply problem. Check that the proper line voltage is available to the power supply.

Localize Trouble Determine the trouble symptom. Use the wiring diagrams in the Schematic Package Supplement to determine which assemblies or major Circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 and, if necessary, refer to the Troubleshooting Guide for detailed troubleshooting procedures.

Visual Check Visually check for obvious problems in the portion of the game where a trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, damaged printed-circuit boards or components.

Check Individual Components

To avoid electrical shock, turn the game off before removing or replacing components.

CAUTION Transistors and integrated circuits soldered in place are difficult to remove without damaging the printed circuit board or component. Be €xtremely careful when removing these components.

Check soldered-in components by disconnecting one end to isolate the measurement from the affects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if acomponent is faulty. However, eliminate the possibility of some other circuit problem existing which could damage the substitute component.

Repair the Assembly Repair or replace the defective part. Refer to Chapter 4, Maintenance and Repair for special repair and replacement procedures. Check for proper operation of any repaired circuit.

Page 31

Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use. ‘To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 4

Page 32

Maintenance Star Wars

Cleaning Requirements

This game cabinet and display shield may be cleaned with any non-abrasive household cleaner. The coin mechanism should be cleaned periodically with hot or boiling water anda mild detergent. A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, flush thoroughly with hot or boiling water and blow out all of the water with compressed ait. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

1, Unlock and remove the rear access panel.

  • Reach up through the rear of the cabinet to the top of the control panel to remove the two nuts and washers that secure the control panel using a %-inch combination wrench.
  • Lift the control panel at the top edge and tilt it toward you. The control panel has foam tape on it. Make sure the tape is in good condition.
Page 33

Star Wars

Flight Control Maintenance

Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. The flight control consists of a handle assembly and a steering assembly. The handle assembly controls the vertical motion, and the steering assembly controls the horizontal motion of the display. Routine maintenance can be performed without removing the flight-control assembly from the game. After any corrective maintenance is performed, the flight control should be recalibrated as described in Chapter 1. Refer to Figures 4-1 and 4-2 for the locations of the parts mentioned in the following procedures. Routine Maintenance Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. Lubrication. Perform periodic lubrication of the flight control assembly as follows (see Figures 4-1 and 4-2):

  • Open the control panel as previously described in this chapter.
NOTE The handle-assembly covers are attached with tamper-proof socket screws. A special 42-inch hex-key tool is supplied with each game (Atari part no. 178126-001).
  • Use the special %-inch hex-key tool to remove the four tamper-proof socket screws from the handle assembly cover.
  • _ Lift off the handle assembly cover and lubricate the following parts inside the flight control: (Refer to Figures 4-1 and 4-2 for an illustration of the lubrication points.)
  • Apply two drops of light machine oil lubricant (Atari part no. 107013-001) to the insides of the four shaft bearings. © Brush a light film of Nyogel 779 lubricant (Atari part no. 178027-001) on the teeth of the two small spur gears.
  • Apply a small amount of WD-40 or a light machine oil to the potentiometer shafts as needed for squeaking. Screw and Nut Tightness. Use the appropriate hex-head and combination wrenches to check the hex-head cap screws and mounting nuts for tightness. Refer to Figures 4-1 and 4-2 for an illustration of the cap screw and mounting nut locations. Maintenance

Removing the Handles Perform the following procedure to remove the handles from the handle assembly (see Figure 4-1):

  • Usea %,-inch hex driver to remove the four cap screws that hold the covers on the handles. Be careful when removing the covers because the trigger and pushbutton springs can fall free from the handles.
  • Unsolder the three harness wires from the trigger and pushbutton microswitches inside each handle.
  • Usea %,4-inch hex driver to remove the four cap screws that hold the handles to the shaft. 4, Usea ¥,-inch punch and gently drive the two roll pins from the shaft.
  • Gently slide the handles from the shaft.
  • Reassemble in reverse order.

Removing the Flight Control

NOTE Certain corrective maintenance procedures can be performed with the flight control attached to the control panel. However, for convenience and to avoid damaging the control panel, we recommend that the flight control be removed from the control panel before any maintenance is performed.

Perform the following procedure to remove the flight control from the control panel:

  • Open the control panel as previously described.
  • Unplug the flight-control harness assembly. Usea 7,-inch combination wrench to remove the four locknuts and washers that mount the flight control to. the control panel.
  • Carefully guide the flight control through the hole in the control panel.
Page 34

Maintenance

Disassembling the Handle Assembly Perform the following procedure to disassemble the handle assembly (see Figure 4-1):

NOTE Removing the handle assembly from the steering assembly is not necessary to perform the procedure below. However, if you wish to do so, refer to Disassembling the Steering Assembly in this chapter for the procedure that describes how to separate the two assemblies.

l. Use the special %,-inch hex-key too} to remove the four tamper-proof cap screws from the handleassembly covers.

  • Remove the handles as previously described.
  • Gently pull the harness wires out of the hollow shaft.
  • Usea %,-inch hex driver to remove the cap screw and washer that hold the spring handle pin to the handle assembly shaft. Slide the spring-handle pin out of the shaft. Use a %4-inch hex driver to loosen the cap screw that holds the large (60 tooth) spur gear to the shaft,
  • Slide the large (60 tooth) spur gear down the shaft to expose the shaft retainer on the right side.
WARNING Shield your face and eyes when prying out the retainers because they can fly loose at a high velocity. Cover the retainers with a rag or any material that will trap the retainer.
  • Use aright-angle slotted screwdriver, or equivalent, to pry the retainer from the shaft.
  • Repeat steps 7 and 8 to remove the retainer on the opposite side.
  • Gently slide the shaft from the housing. Be careful not to lose the torsion springs. ll. Usea %4-inch hex driver to loosen the cap screw that holds the small (i4 tooth) spur gear to the potentiometer shaft. 12, Usea %-inch combination wrench to remove the nut and washer that hold the potentiometer to the mounting bracket.
  • Slide the potentiometer from the bracket. Be careful not to lose the smail spur gear, nut, and washer.
  • Use a 45-inch nex-head wrench and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the handle assembly as described in the following procedure. Star Wars

Reassembling the Handle Assembly Follow the steps below to reassembie the handle assembly (see Figure 4-1):

  • Use a %-inch hex driver and %-inch combination wrench to install the two bumpers on the frame.
  • Insert the large (60 tooth) spur gear with the collar facing away from the bearing. Hoid the gear in line with the bearing hole. (The gear fits through the sloton the right front of the frame.)
  • Slide the shaft through the right-hand bearing and the spur gear. Do not insert the shaft past the outside edge of the spur-gear collar.
  • Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-00)) to the inside of the springs.
  • Hook the straight end of the first torsion spring through the hole closest to the right side of the frame.
  • Hold the first torsion spring in line with the shaft so that the looped end of the spring is facing away from the spur gear.
  • Slide the shaft just through the first torsion spsing.
  • Hook the straight end of the second torsion spring through the hole closest to the left-hand bearing.

9. Hold the second torsion spring in line with the shaft

so that the looped end of the springis facing the first torsion spring.

  • Slide the shaft through the second torsion spring and the left-hand bearing. ll. Position the shaft so that the retainer grooves are just inside the bearings.
  • Install the two retainers in the shaft grooves.
  • Turn the shaft so that the two large holes and the smaller centered hole are facing upward.
  • Locate the hole in the spring-handle pin. Insert the end of the spring handle pin that is closest to the hole through the slot in the frame and through the hole in the shaft. Make sure that both torsion spring looped ends are wrapped over the spring handle pin.
  • Position the spring-handle pin so that the hole in the pin is aligned with the hole in the shaft.
  • Usea %4-inch hex driver to tighten the cap screw and washer that secure the pin to the shaft.
  • Align the cap screw in the spur-gear collar with the threaded hole in the shaft, and use a %,-inch hex driver to tighten the cap screw.
  • Insert the potentiometer shaft through the hole in the mounting bracket. Place the washer, nut, and small (14 tooth) spur gear (with the collar facing inward) onto the shaft before fully inserting the shaft through the bracket.
Page 35

Star Wars Maintenance

  • Align the potentiometer so that the tab key is inserted 24, Use a %-inch combination wrench to tighten the into the keying slot. potentiometer to the mounting bracket.
  • Usea %-inch combination wrench to slightly tighten 25. Perform the procedure for installing the harness the nut on the potentiomeier shaft. assembly provided at the end of this chapter. 21, Turn the potentiometer shaft so that the flat side faces 26, Install the handles in the reverse order of the removal the center wire terminal.
  • Align the cap screw on the small (14 tooth) spur gear with the flat side of the shaft. Use a %4-inch hex driver to tighten the cap screw.
  • Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then pull the potentiometer and small (14 tooth) spur gear away from the large spur gear about 44-inch.

Wire & Cable Tie

Retainer Potentiometer

Red White Black

Bearing

Shaft

Second Torsion Spring

Labeled Spring Pin Sleeve (R) procedure previously described. Do not install the handle covers until the harness is installed and the proper wires are soldered to the trigger and pushbutton microswitches.

Check the vertical potentiometer alignment as described under Aligning the Potentiometers. . Install the handle assembly cover and use the special 42-inch hex-key tool to tighten the four tamper-proof socket screws that secure the cover to the handle assembly.

Tab Key

Harness Assembly

Handle Assembly ~~ Collar

Trigger Microswitch Black

)

Pushbutton First Torsion Microswitch

Spring Black Collar Red

Spur Gear (Common)

oe (Normally Open) Spur Gear Self-Locking

4 Lubrication Points Cap Screw

Cover

Figure 4-1 Handle Assembly

Page 36

Maintenance

Disassembling the Steering Assembly Perform the following procedure to disassemble the steering assembly (see Figure 4-2):

  • Remove the handle covers as described earlier in this chapter. Remember, be careful when opening the handles because the pushbutton and trigger springs may fall out.
  • Unsolder the three harness wires from the vertical potentiometer, handle pushbutton microswitch, and trigger microswitch.
  • Use a %,4-inch hex driver (or ball-end driver) to remove the three cap screws that hold the steering-assembly shaft to the handle-assembly frame. Genuy pull the two assemblies apart. Make sure the harness wires are free to slide out of the handleassembly shaft. Be
  • Usea ¥.-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut faces the open end of the frame.)
  • Slide the anchor pin out of the shaft.
  • Grasp the large (60 tooth) spur-gear and slide the shaft from the frame. The bearing spacer, torsion springs, and large flat washer will fall free.
  • Use a %4-inch hex driver to remove the cap screw holding the large spur gear to the steering shaft anda %a-inch hex driver to remove the set screw that holds the small spur gear to the potentiometer shaft.
  • Usea ¥%-inch combination wrench to remove the nut and washer that hold the potentiometer to the frame.
  • Unsolder the three harness wires from the potentiometer terminals.
WARNING Shield your face and eyes when prying the retainer from the shaft since the retainer can fly loose at a high velocity. Cover the retainer with a rag or any material that will trap the retainer.
  • Use aslotted screwdriver, or equivalent, to remove the retainer from the shaft.
  • Use a %2-inch hex driver and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the steering assembly as described in the following procedure.

Reassembling the Steering Assembly Perform the following procedure to reassemble the steering assembly (see Figure 4-2):

  • Use a %2-inch hex driver and %-inch combination wrench to install the two bumpers to the frame.

4-6 6.

Star Wars

Snap the retainer into the groove in the shaft and slide the large flat washer down the long end of the shaft and against the retainer. Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the springs. Hook the straight end of the first torsion spring through the hole closest to the rear of the frame. Slide the shaft through the outside bearing and the first torsion spring. Hook the second torsion spring through the hole on the opposite side and closest to the front of the frame. Slide the shaft through the second spring and the opposite bearing. Turn the shaft so that the threaded hole at the retainer end of the shaft faces up toward the open side of the frame. The hole through the center of the shaft will then be perpendicular to the open side of the frame. Use a $-inch combination wrench to install the anchor pin and nut through the hole in the center of the shaft. Make sure the torsion spring looped ends are wrapped under the anchor pin and nut.

Slide the large (60 tooth) spur gear onto the shaft with

the collar facing out. Align the cap screw in the spur-gear collar with the threaded hole in the shaft and use a %,-inch hex driver to tighten the cap screw. |. Insert the potentiometer shaft through the hole in the frame and align the potentiometer so that the tab key is inserted into the keying slot. . Install the washer and nut on the potentiometer shaft but do not tighten. Turn the potentiometer shaft so that the flat side faces the center wire terminal. . Align the cap screw on the small (28 tooth) spur gear with the flat side of the shaft and slide the small spur gear (with the collar facing inward) onto the potentiometer shaft.

. Position the spur gear so that its teeth mesh with those of the large spur gear and use a %,-inch hex driver to tighten the set screw. . Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the potentiometer and small spur gear away from the large spur gear about %,-inch. . Use a %-inch combination wrench to tighten the potentiometer to the frame. . Slide the bearing spacer over the shaft at the end opposite the spur gears. . If necessary, lubricate the steering assembly as previously described.

Page 37

Star Wars

NOTE The remaining steps describe the procedure for attaching the steering assembly to the handle assembly.

. Insert the steering-assembly shaft into the collar on the handle-assembly frame. . Align the three holes in the steering-assembly shaft with the three holes in the handle-assembly collar. Use a %,-inch hex driver (or ball-end driver) to tighten the three cap screws.

. Install the harness assembly as described in the following procedure. . Check the horizontal potentiometer alignment as described under Aligning the Potentiometers.

Retainer

First Torsion Spring

Second Torsion Spring

Anchor Pin

Shaft

Bumper

Bearing Spacer Spur Gear Maintenance

Installing the Harness Assembly Perform the following steps to install the harness assembly into the flight control (see Figures 4-1] and 4-2): If necessary, remove the handle cover as described under Removing the Handles. Guide the harness wires into the spur-gear end of the hollow steering-assembly shaft. Route and solder the wires to the potentiometers and microswitches. Note that the wire bundle that goes to the right handle lentified with a labeled sleeve (R). Install the wire ties and the ground clip.

Harness Assembly

A ry

Small Spur Gear

Large Flat Washer

Green

Keying Slot

Ground Clip

Black ‘Anchor Nut

Potentiometer

4 Lubrication Points

Figure 4-2 Steering Assembly

Page 38

Maintenance

Aligning the Potentiometers The following procedures describe the method for checking and aligning the vertical and horizontal flight control potentiometers to ensure that the target cursor on the display is centered when the flight control is released. Preliminary Procedure Perform the following procedure to determine if the vertical and/or horizontal potentiometers are misaligned:

  • Set the SelfTest switch to the on (up) position
  • Perform the Switch Test Display procedure for checking potentiometer alignment as described in Chapter
  • If the self-test display (POT TEST portion) indicates that the flight control vertical and/or horizontal alignment is out of tolerance, perform the appropriate procedure(s) as follows:

Vertical Potentiometer Alignment Perform the following procedure to align the flight control vertical potentiometer (see Figure 4-1):

  • If necessary, remove the flight control handle assembly cover with the special ¥.-inch hex-key tool to gain access to the vertical motion potentiometer. With the flight control centered (no tension on the return springs), check that the set screw on the potentioeter spur gear is facing the center (white) wire terminal. If not, use a %-inch combination wrench and loosen the potentiometer mounting nut. Slide the potentiometer sideways in the mounting bracket until the gears disengage. i)
  • Turn the small spur gear until the Switch Test Display obtained in the Preliminary Procedure indicates that the vertical potentiometer is within the allowable limits. Gently slide the potentiometer forward so that the spur gear teeth are tightly meshed (if necessary, move the large spur gear slightly to align the gear teeth—do

EN oy Star Wars

notturn the potentiometer shaft). Recheck the Switch Test Display to make certain the potentiometer alignment is still within allowable limits. Pull the potentiometer and small spur gear away from the large spur gear about 44-inch and use the %-inch combination wrench to tighten the potentiometer to the mounting bracket. Install the handle assembly cover by using the special %,-inch hex-key tool to tighten the tamper-proof socket screws.

Horizontal Potentiometer Alignment Perform the following procedure to align the horizontal potentiometer (see Figure 4-2): 1. Open the game control panel as described previously in this chapter. With the flight control centered (no tension on the springs), check that the set screw on the potentiometer spur gear is facing the center (white) wire terminal. If not, use a %4-inch hex drive and loosen the set screw on the potentiometer spur gear. Slide the spur gear off the potentiometer shaft. Turn the potentiometer shaft until the Switch Test Display obtained in the Preliminary Procedure indicates that the vertical potentiometer is within allowable limits. Slide the spur gear onto the potentiometer with the set screw centered over the flat side of the shaft while aligning the gear teeth so they mesh with the large spur gear (if necessary, the small spur gear can be turned slightly—do not turn the potentiometer shaft). Use the %,-inch hex driver and tighten the spur-gear set screw. Recheck the Switch Test Display to make certain the potentiometer alignment is still within allowable limits. If not, repeat parts 2 through 4.

Page 39

Star Wars

Removing the CRT Assembly

The cathode-ray tube (CRT) assembly may implode if struck or dropped. Shattered glass can cause personal injury within a 6-foot radius. To reduce the risks of injury to people or of damage to the game components, we recommend that two peopie perform the following removal procedures.

Perform the following procedure to remove the CRT assembly from the game (see Figure 4-3):

  • Remove the rear access panel from the cabinet.
  • Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attach one end ofa large, well insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.
  • Disconnect the CRT neck-pin connector, anode lead, yoke connector (J105 on the Deflection PCB), degaussing coil connector (J104 on the Deflection PCB), and the 1-pin DAG spring connector.

‘Lower Housing

Display Shield

Display Bezel Maintenance

Fad Qpen the control panel as previously described in this chapter.

  • Remove the hardware that secures the lower housing to the cabinet. Then remove the housing.
  • Carefully remove the display shield and the display bezel.
  • Remove the hardware that secures the lower housing retainer to the cabinet. Then remove the retainer.
WARNING Be extremely careful when removing the CRT mounting bolts because the CRT assembly can fall. We recommend that a second person carefully hold the CRT neck while the mounting bolts are being removed.
  • Usea %4-inch combination wrench to remove the four bolts and washers from the front of the display mounting bracket.
  • Carefully lift the CRT assembly from the front of the cabinet.
  • Reinstall the CRT in the reverse order.
NOTE Readjust the brightness, purity, and convergence as described in the Display Manual whenever the CRT is replaced.

CRT

Mounting Bracket

\ CRT Neck

Vj //

Figure 4-3 Removing the CRT Assembly

Page 40

Maintenance Star Wars

oe st:

Wiring the Utility Panel Controls

Refer to Figure 4-4 for the proper wire connections when replacing the controls that are mounted on the utility panel White/Yellow

‘Orange

Yellow Before removing or repairing the utlity panel, turn the game off. Players may receive an electrical shock if the utility panelisnot properly grounded! Atter servicing any parts on the panel, make sure that the ground wireis firmly attached to the back of the coin White/Red counter.

Brown

Red

Orange/Blue Orange/White/Violet First Coin Counter Second Coin Counter

Black (Common)

Gray (Normally Open) White

NOTE Only the Iretand-built cabinet hastwo coin counters.

Figure 4-4 Utility Panel Wire Colors

Page 41

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged al phanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99; then 000598through approximately 201000, When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 5

Page 42

Star Wars Mlustrated Parts Lists

Fluorescent Tube & Speaker See Figure 5-4 8040378-01 Attraction Panel with Decal

040369-01 Attraction Panel Retainer 78-6900402 Tape 040370-01 Speaker Grille

040371-01 040377-01 Display Shield Display Bezel

A040975-01 Lower Housing & Flight Control Decal Assy: See Figure 5-3

A040374.01 Control Panel Assy. ‘A040373-01 Contro! Panel with Decal 040233-01 Flight Control 178034-024 = 040372-01 TMolding a a: Control Panel (040380-03 Decal-not shown 78-6900402 Coin Door Assy. Tape See Figures 5-6 or 5-7

Utility Panel Assy. See Figure 5-5

038091-01 Molded Coin Box

Figure 5-1A Cabinet-Mounted Assemblies US-Built Cabinet A040344-01 J

5-2

Page 43

Star Wars Illustrated Parts Lists

A040345-01 Cabinet Assy.

037332-01 Ventilation Grille

A038881-01 Lock

A200009-01 Atari Display Kit Assy. Refer tothe Display Manual High-Voltage PCB Assy. Refer to the Display Manual 040129-01 Access Panel

Deflection PCB Assy. Refer to the Display Manual

040376-01 040376-02 Static Shield Static Shield EMI Cage 038870-01 7 See Figure 5-9 Coin Box Enclosure Regulator/Audio Il PCB See Figures 5-9 & 5-11 A040467-01 Power Harness Assy. A040466-01 171002-001 Main Harness Assy. Fan ¢€) 040546-01 Fan Bracket 178093-001 Fan Blade Guard A040547-01 Fan & Bracket Assy. EMI Shield PCB ~< See Figures 5-9 & 5-10 Power Supply Assy. See Figure 5-8 037243-01 Base Plate

A038600-01 Power On/Off Switch Assy, O 009992-01 A037453-03 Mt re In/Off Switch Cover 178048-001 Power Cord Caster

Figure 5-1A Cabinet-Mounted Assemblies, continued US-Built Cabinet A040344-01 J

Page 44

Mlustrated Parts Lists Star Wars:

Cabinet-Mounted Assemblies US-Built Cabinet Parts List

Part No. Description

A037453-03Strain-Relief Power Cord(U.S. and Canada)

A038600-01 Power On/Off Switch and Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A040345-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A040374-01 Control Panel Assembly—includes: A040233-01 Flight Control 040372-01 Control Panel 040380-03 Decal for Control Panel (not shown) A040375-01 Lower Housing and Decal Assembly A040378-01 Attraction Panel and Decal Assembly A040466-01 Main Harness Assembly 404046701 Power Harness Assembly 200009-01 Atari 19-Inch Color XY Display Kit Assembly— includes: A201106-01 Cathode-Ray Tube Assembly (not shown) A201014-01 Deflection PCB Assembly A201012-01 High-Voltage PCB Assembly The following four items are technical information supplements to this game.

SP-225 Star Wars Schematic Package ST-225 Star Wars Label with Self-Test Procedure and Option Switch Settings TM-225 Star Wars Operators Manual with Illustrated Parts Lists T™M-239 Auri 19-Inch and 25-Inch Color XY Display Manual 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4 -Inch Wide x %- Inch Thick (apply 36 inches to the surrounding edge of the control panel and 46 inches to the attraction panel.) 009992-01 OniOff Switch Cover

034536-01Foam Pad—1 4-Inch Thick(located between the Deflection PCB and the cabinet wall and the

High-Voltage PCB and the cabinet wall—not shown)

034536-02Foam Pad—'-Inch Thick(located between the Regulator/Audio PCB and the EMI Cage, and between the

EMI Cage and the cabinet wall—-not shown)

037243-01Base Plate for Power Supply(not shown)

037332-01 Ventilation Grille 038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 040129-01 Rear Access Panel (does not include lock) 040369-01 Attraction Panel Retainer 040370-01 Speaker Grille 040371-01 Video Display Shield 040376-01 Static Shield 040376-02 Static Shield 04037701 Video Display Bezel

5-4 (Continued on next page)

Page 45

Star Wars Illustrated Parts Lists

Cabinet-Mounted Assemblies US-Built Cabinet Parts List, continued

Part Description

A040547-01 Fan and Bracket Assembly—includes: 040546-01 Fan Bracket 171002-001 Fan 178093-001 Fan Blade Guard

178034-024 %-Inch Black Plastic TMolding 178048-001 2-Inch Rigid Caster 178126-001 Hex Wrench for Cabinet-Mounted Assys. (not shown—it is shipped in the coin box and required for the tamper-proof screws on the flight control)

Page 46

Ilhustrated Parts Lists Star Wars

Fluorescent Tube & Speaker 78-6900404 See Figure 5-4 Tape 040136-01 Attraction Pane! Shield

040379-03 Attraction Panel Decal

040369-01 Attraction Panel Retainer 040371-01 Display Shield

040370-01 040377-01 Speaker Grille Display Bezel

Flight Control See Figure 5-3 A040375-01 Lower Housing & Decal Assy.

A200009-01 Atari Display Kit Assy. Refer to the Display Manual

Coin Door Assy. See Figure 5-6

A040374-01 Control Panel Assy. A040373-01 Control Panel with Decal A040233-01 Flight Control 040372-01 Control Panel 040380-03 Decal-not shown 78-6900402 Tape 038091-01 Molded Coin Box

78-3201 Glide Utility Panel Assy. See Figure 5-5

Figure 5-1B Cabinet-Mounted Assemblies Ireland-Built Cabinet A040344-10 J

Page 47

Star Wars

A040345-01 Cabinet Assy.

High-Voltage PCB Assy. Refer to the Dispiay Manual

040376-02 Static Shield

0377496-01 Coin Box Enclosure

A040547-01 Fan & Bracket Assy. 171002-001 Fan 040546-01 Fan Bracket 178093-001 Fan Blade Guard

A040467-01 Power Harness Assy. ustrated Pacts Lists

178034-024 TMolding

. 037332-01 Ventilation Grille

A038881-01 Lock

040129-01 Access Panel

Deflection PCB Assy. Refer to the Display Manual

040376-01 Static Shield

Regulator/Audio tI PCB ‘See Figures 5-9B & 5-11

Printed-Circuit Board Assemblies See Figure 5-9B

The housing contains the Main PCB See Figure 5-12 Analog Vector- Generator PCB See Figure 5-13 Sound PCB See Figure 5-14

A040466-01 Main Harness Assy.

178048-001 Caster

A038600-01 a Supply Assy. Power On/Ott Switch Assy. ee Figure 5: oveaseo1 A037784-03

On/Off Switch Cover Power Cord

Figure 5-1B Cabinet-Mounted Assemblies Ireland-Built Cabinet A04040344-10 J, continued

Page 48

IMustrated Parts Lists Star Wars

Cabinet-Mounted Assemblies Ireland-Built Cabinet Parts List

Part No. Description

A038600-01 Power On/Off Switch and Mounting Plate Assembly A037784-03 Strain-Relief Power Cord (England and ireland) A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no, A038881-03 A040345-01 Cabinet Assembly _ (includes glides and PCB retainers, but not the rear access panel)

A040374-01 Control Panel Assembly—includes: A040233-01 Flight Control 040372-01 Controi Panel 040380-03 Decal for Conirol Pane}

A040375-01 Lower Housing and Decal Assembly. A040466-01 Main Harness Assembly A040467-01 Power Harness Assembly A040547-01 Fan and Bracket Assembly—includes: 040546-01 Fan Bracket 171002-001 Fan 178093-001 Fan Blade Guard

A040549-O1 19-Inch Atari Color XY Cathode-Ray Tube (CRT) and Bracket Assembly — includes: A200009-01 19-Inch Atari Color X-Y Display Kit Assembly-—inciudes: A201106-0) CRT Assembly (not shown) A201014-01 Deflection PCB Assembly A201012-01 HighVoltage PCB Assembly 201018-01 19-Inch CRT Bracket

The following four items are technical information supplements to tbis game.

SP-225 Star Wars Schematic Package S¥-225 Star Wars Label with Self‘lest Procedure and Option Switch Settings TM-225 Star Wars Operators Manual with Illustrated Parts Lists TM-239 19-Inch Ari Color XY Display Manual

78-3201 Adjustable Glide 78-6900402

78-6900404

009992.01

034536-01

034536-02

03733201

038091-01 038870-01 040129-01 640136-01

040369-01 040370-01 040371-01 040376-01 Vinyt Foam Single-Coated Adhesive Tape, 4-Inch Wide x %- Inch Thick (apply 36 inches to the surrounding edge of the control panei—not shown) Vinyl Foam Single-Coated Adhesive Tape, ¥s-Inch Wide x %- Inch Thick (apply 46 inches to the attraction panel—not shown) On/Off Switch Cover

Foam Pad—t %-Inch Thick {located between the Deflection PCB and the cabinet wall and the High-Voltage PCB and the cabinet wall—not shown) Foam Pad—%-Inch Thick (located between the Regulator/Audio PCB and the PCB housing, and between the PCB housing and the cabinet wall—not shown) Vemilation Grille

Molded Coin Box Coin Box Enclosure Rear Access Panel (does not include lock) Attraction Panel Shield

Attraction Panel Retainer Speaker Grille Video Display Shield Static Shield

(Continued on next page)

Page 49

ee Star Wars Mlustrated Parts Lists

Cabinet-Mounted Assemblies Ireland-Built Cabinet Parts List, continued

Part No. Description

040376-02 Static Shield 040377-01 Video Display Bezel 040379-03 Attraction Panel Decal 178034-024 \%4-Inch Black Plastic TMolding 178048-001 2-Inch Rigid Caster 178126-001 Hex Wrench for CabinetMounted Assys. (not shown—shipped in the coin box and used for the tamper-proof screws on the flight control)

5-9

Page 50

Mustrated Parts Lists

040379-04 Attraction Panel Decal

040382-04 Left Housing Decal

040381-04 Flight Control Decal

040380-03 Control Panel Decal

Figure 5-2 Star Wars Decals

5-10 Center Housing Decal

Star Wars

Page 51

Star Wars

Figure 5-2 Star Wars Decals lustrated Parts Lists

Parts Lists

Part No. Description

040379-04 Attraction Panel Decal 040380-03 Control Panel Decal 040381-04 Flight Control Decal 040382-04 Left Display-—Housing Decal 040382-05 Cemer Display—Housing Decal 040382-06 Right Display—-Housing Decal (not shown)

Page 52

Star Wars Illustrated Parts Lists

A040251-01 Steering Cover & Decal Assy, — 176025-3604 ; Tamper Proot Cap Screw

040093-02 Left Handle Cover

040091-01 Left Handle 72-8812 19-9026 178012-001 » Retaining Ring Cap Screw ‘otentiometer

040240-01 weener ‘040468-01 Hani Harness 176022-3606 ~~ Self Locking Screw 72-8010 Screw

73-20807 Roll Pin

040252-01 040303-01 Trigger 040243-01 Compression Spring Bearing 72-1206 Screw 040093-01 040244-01 Right Handle Cover Spring Pin

040246-01 A040247-01 Handle Spring Handle Assy. Frame

040242-01 040235-01 Handle Shaft eae 040473-01 17602-3604 = Wire Self-Locking Screw a60026-004

Switch 176022-3606 ae Selt-Locking Screw _73-21206 Roll Pin 040096-01 See Chapter 4 for lubrication information. 040091-02 Button Right Handle

Figure 5-3 Flight Control Assembly A040233-01 D

5-12

Page 53

Star Wars Illustrated Parts Lists

178012-001 Retaining Ring

040238-01 Pin 175002-001 Large Washer 040234-01 | Steering Shaft |

Pe A 040239-01 Spring SN \

177010-241 Nut . 175002-004 a) Flat Washer 040235-01 Gear A040236-01 Steering Assy. Frame

040237-01 72-8010 Nut

178101-003 Gear

19-9026 Potentiometer

040240-01 040241-01 Bumper Spacer Bearing

See Chapter 4 for lubrication information.

Figure 5-3 Flight Control Assembly, continued A040233-01 D

5-13

Page 54

Illustrated Parts Lists

Flight Control Assembly Parts List

Part No. Description

A040236-01 Steering Assembly Frame—includes: 040243-01 Modified Bearing 040555-01 Steering Frame Weldment 72-L28510 #%4-20 x %-Inch Long Self-Clinching Stud A040247-01 Handle Assembly Frame—includes: 040243-01 Modified Bearing 040556-01 Frame Handie Weldment A040251-01 Steering Cover and Decal Assembly: 040248-01 Cover 040382-07 Decal A040468-01 Flight Control Harness Assembly 19-9026 5 k® Potentiometer 72-1206F #2-56 x %-Inch Cross-Recessed Pan-Head Machine Screw 72-8010 #10-32 x %-Inch Socket-Head Cap Screw 72-8812 #832 x ¥%-Inch Socket-Head Cap Screw 73-21206 Roll Pin 73-20807 Inch Diameter x 7s-Inch Long Spring Roll Pin 75-0488 #8 SplitLock Washer 75-07020 0.390-Inch i. D. Flat Washer 040091-02 Right Handle 040091-01 Left Handle 040093-01 Right Handle Cover 040093-02 Left Handle Cover 040096-01 Button, 040234-01 Steering Shaft 040235-01 60-Tooth Spur Gear 040237-01 Anchor Nut 040238-01 Anchor Pin 040239-01 Steering Torsion Spring 040240-01 Stop Bumper 040241-01 Spacer Bearing 040242-01 Handle Shaft 040244-01 Spring Pin 04024601 Handie Torsion Spring, 040249-01 14-Tooth Spur Gear 040252-01 Compression Spring 040303-01 Trigger 040473-01 Jumper Wire 160026-001 SPDT Snap Switch 175002-001 0.750-Inch I, D, Large Washer 175002-004 #10 Flat Washer 176022-3604 #6-32 x Y-Inch Self-Locking Socket-Head Cap Screw 176022-3606 #6-32 x %-Inch Self-Locking Socket-Head Cap Screw 1760253604 #6-32 x ¥4-Inch Tamper-Proof Self-Locking Button-Head Cap Screw 176026-3610 #632 x ¥-Inch Tamper-Proof Socket-Head Cap Screw 177010-241 #10-32 Nylock Hex Nut 178012-001 Retaining Ring for .750-Inch Diameter Shaft 178101-003, 28-Tooth Spur Gear

Page 55

Star Wars illustrated Parts Lists

NOTE To ensure that the fluorescent tube ba dali starts, make sure the ground wireis peaker firmly attached to both the ballast transformer and the steel tube bracket.

99-11003 Starter ‘A040469-01 Harness 179035-001 Tube Holder

037469-01 99-11008 Bracket Socket

142028-001 Transtormer

79-561816P_ Wire Nut A037540-01 Ground Wire

Figure 5-4 Fluorescent Tube and Speaker Assembly A040383-01 A Parts List

Part No. Description

A037540-01 Ground Wire with Ring Lug A040469-01 ‘Tube and Speaker Harness Assembly 70-304 18-Inch, 15-Watt, Cool White Fluorescent Tube

79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

037469-01 Steel Tube Bracket 142028-001 60 Hz, 118 V, Ballast Transformer (used on A040378-01 assembly) 148001-013 6x 9-Inch Oval, 4 @, 6-Ounce, Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Tube Holder

5-15

Page 56

Tilustrated Parts Lists Star Wars

A039254-01 Harness Assembly

Betore removing or tepairing the utili typanel, turn the game off. Players may receive an electrical shock if the utility panel is not properly grounded! Aiter servicing any parts on the panel, make sure that the ground wire isfirmly attached to the bracket.

A002465-01 Coin Courier

176018-002 Screw

69-001 SelfTest Switch 75-9910W0 Stamped Nut 119006-103 040412-01 Volume Controt Bracket

62.041 Auxiliary Coin Switch

NOTE Only the Ireland-built cabinet has two coin counters.

Figure 5-5 Utility Panel Assembly US-Built Cabinet A040413-01 B Ireland-Built Cabinet A040413-02 B Parts List

Part No. Description

A002465-01 Coin Counter A039254-01 Volume Control Harness Assembly (includes grounding clip) 62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self‘Test Switch 040412-01 Component Bracket 75-9910W0, 74, Stamped Nut 119006-103 Volume Control 176018-002 #6-32 x %-Inch Machine Screw

5-16

Page 57

Star Wars Illustrated Parts Lists

5-17

Page 58

Ulustrated Parts Lists Star Wars,

170000-001 Lamp 179047-001 NN re < 99-15083

Lamp Base & PS Base Plate

99-15026 7 99-15040 (Coin Inlet) ~ Lever 99-15056 Screw tor Bezel

99-15025 z) Con inet OF

99-15055 Retaining Screw ) | 9915054 ~ Pivot for Lever

99-15027 Side Plate 7 Coin Return .

@. r ;

iS 99-15028 T5945 i

Hex Nut We Coin Return Box

Lock Wash.

99-15056 _ Screw tor Bezel

99-1504: Switch

7244148 Screw

Figure 5-6 Vertically Mounted Coin Door 171034-xxx A

5.18

Page 59

Star Wars,

A037542-01 Harness—not shown .

99-15063 Screw

99-15067 Lock Assy.

036091-01 Coin Box Illustrated Parts Lists

99-15067. Lock Assy. 99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

99-15052 Spring for Button

99-15071 Clamp

99-15039 Bezel for Cover

99-15066 Screw

tee > ie _ F o — o

1 ST 99-15072 " Door Frame 99-15073 99-15070 “ _ Upper Door |} Doors and Frame s) - 99-15074 2 Lower Door

171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/5 DM Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-015 — French 2 Frit Fr Coin Door

Figure 5-6 Vertically Mounted Coin Door, continued 171034-xxx A

5-19

Page 60

Mbustrated Parts Lists Star Wars

Vertically Mounted Coin Door Assembly Parts List

Part No. Description

A036597-01 Harness Assembly _(Ireland-Built cabinet only) A037542-01 Harness Assembly 72-1414 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal‘Tooth Zinc-Plated Steel Lock Washer 75-9148, #4-40 Steel Machine Hex Nut 75-3448 #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25-cent Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003, Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 9915005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008. Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20-cent Price Plate

99-15011 Coin Return Button with Italian 100 Lite Price Plate 99-15025 Left Half of Coin Inlet 9915026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029, Switch Bracket 99-15036 Metal Coin Return Cover 99-15038. Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Button, 99-15042 Coin Switch for U.S. 25 cents 99-15052 Spring for Coin Return Button 99-15055 Retaining Screw 99-15056 #4-40 x ¥{o-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063, Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99415071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 lower Door 99-15075 Switch Adjuster 99-15083 Base Plate—includes: 99-15040 Lever 99-15054 Pivot for Lever 038091-01 Coin Box—not included in assembly (Acceptable substitute is part no. A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 171050-001 Dual Entry Face Piate 179047-001 Lamp Base

Page 61

Star Wars Illustrated Parts Lists

171006-035 99-10140 Coin mechanism Panel assy.

99-10116

99-10152 Right coin inlet 99-10096 Fastener 75-9448 Locknut

99-10151 Left coin inlet

‘99-10080 Lamp socket _— 70-11-47 “\ 4 Lamp & Zr a / 99-10104 Bar retainer 72-9406S Screw 99-10147 Harness

99-10154 Bracket assy. |

99-1042 thru 99-10045 99-10153 Coin switch assy, a i

Coin return box . >] a i 65-441C Qo 7 Sp. Coin switch

99-10150 x os N Switch cover 99-10075 thru 99-10078 _— ‘Switch wire 9910008 75-1412S Retainer Screw

Figure 5-7 American-Made Coin-Door Assembly 171027-001 A

Page 62

Illustrated Parts Lists

99-10139 Cain door ——>| 72-HA1404C

Coin box 99-10148 Lock assy.

Screw

—S; 99-10119 Button assy Star Wars

99-10142 Button housing

99-10134 Cover

99-10118 Button

99-10115 Spring

99-10141 Com return cover

99-10117 Coin return door

99-1014 ge Channel cip SS

99-10149 Service door

99-10143 Frame

Figure 5-7 American-Made Coin-Door Assembly, continued 171027-001 A

Page 63

Alustrated Parts Lists Star Wars

American-Made Coin-Door Assembly Parts List

Part No. Description

171006035 Metal Coin Mechanism for US. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp. 72-9408 #4-40 x ¥-Inch Truss-Head Screw

72-HA1404C #4-40 x %4-Inch Pan-Head Screw J2JAL405B #4-40 x .31-Inch Pan-Head Screw 75-14128, #4-40 x 34-Inch Pan-Head Screw 75-9448 #4-40 Lock Nut

9910008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S, $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, ttalian 100 L, US. $1.00 9940045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-1007 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-1081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-1015 Spring

99-1016 Plastic Coin Return Lever 99-1017, Steel Coin Return Door 9910118 Amber Coin Return Button 99-1009 Amber Coin Button for US. $.25 99-1013 4 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99410143, Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam 99-10146 Coin inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10148. Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 9930153 Coin Return Box 99-10154 Bracket Assembly

5-23

Page 64

Mlustrated Parts Lists Star Wars

NOTE Power supply base plate is not shown. For part number, see Figure 5-1

Fuse block cover must be in place during game operation. ‘A037395-01 Transformer Assembly

A021084-02 Vottage Pug Rea

‘A037479-02 Voltage Plugs

Capacitor 034544-01 Fuse Cover

79-4411001 Fuse Post

46-2017002 fice Ral

46-2014002 v Fuse

034482-02 a Chassis, 78-70501SC Capacitor Bracket '

A035891-02 Fuse Harness

78-2708 Bushing

79-3206 A034630-01 Fuse Block Filter Assembly

46-2014002 Fuses

79-15021001 Terminal Biock A035890-01 Power Harness

SA-MDA35O1 © A034629-01 Rectifier AC Harness

Figure 5-8 Power Supply Assembly US-Built A037396-04 F Ireland-Built A037396-06 F

5-24

Page 65

Star Wars Illustrated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.

For -04 Version

FlLabel for Fuse Value037639-01
FI7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2017002
BVoltage Plug for 120 V_{yellow wire color)A021084-02

For -06 Version

FILabel for Fuse Value037639-02
FI4 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse46-2014002
JBVoltage Plugs for 220 V_(blue wire color) and 240 V_(brown wire color)A037479-02

For -04 & -06 Versions

cl27,000 uF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Brackei78-70501SC
CRIType-MDA 3501 Bridge Rectifier3A-MDA3501
FIPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-4411001
F24 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
F4-F64A, 250 V, 3AG Slow-Blow Glass Cartridge-‘Type Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

F2-F6,5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6.Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037641-01
F42-Circuit Single-Row Terminal Block(located under F4)79-15021001
FLIRFI Filter Assembly(designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
J4AAC Harness AssemblyA034629-01
TlTransformer Assembly(designation covered)A037395-01

Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x *%,-Inch Outside 78-2708 Diameter x %-Inch Thick Power Supply Chassis Basé 034482-02

Page 66

Illustrated Parts Lists

037873-01 Spacer A038463-21 Analog Vector-Generator PCB ‘See Figure 513

4040472-01 Interconnect Cable

178140-2612 PCB Spacer

72-1606S. Screw

178120-212 PCB Support

178120-206

Screw

A040255-01 interconnect PCB

A040260-21 Sound PCB See Figure 5-14 176021-004 Screw

A035435-02 Regulator/Aucio I! PCB See Figure 5-11

A040301-01 Tray and Guides Assembly 178047-022 040300-01 Guide Mounting Tray

A037701-03 178047-032 Mt hG Guid Grounding clip El cocci uides ide not shown. EMI Cage

Figure 5-9A PCB Mounting Hardware US-Built Cabinet

5-26 PCB Support Taser

A038461-21 Main PCB See Figure 5-12

176015-112

A040258-01 EMI Shield PCB See Figure 5-10 Star Wars

T2-1604F . Screw

NOTE The Federal Communications Commission requires that the gamePCBs be housed in the EMi cage with the EMI Shield PCB attached,

175009-221 Plastic Washer

178044-242 Grommet

178045-442 Fastener

Page 67

Star Wars Illustrated Parts Lists

PCB Mounting Hardware US-Built Cabinet Parts List

Part No. Description

A035435-02 Regulator/Audio Il PCB A037701-03 EMI Cage and Guides Assembly—includes: 178047-032 16-Inch Snap-In PCB Guide (four required) 037700-02 EMI Cage A038461-21 Star Wars Main PCB Assembly A038463-21 Stars Wars Analog Vector-Generator PCB Assembly A040255-01 Stars Wars Interconnect PCB Assembly A040258-01 EMI Shield PCB Assembly—includes: 72-1404F #4-40 x %-Inch Cross-Recessed Steel Screw 037873-01 Spacer 175009-221 Plastic Washer 178044-242 Grommet 178045-442 Snap-In Fastener A040260-21 Stars Wars Sound PCB Assembly A040301-01 Tray and Guides Assembly—includes: 040300-01 Mounting Tray for Regulator/Audio I] PCB 178047-022 1l-Inch Snap-In PCB Guide (two required) A040472-01 Interconnect Cable 72-1604F #6-32 x %4-Inch Cross-Recessed Pan-Head Screw 72-1606S #6-32 x %-Inch Pan-Head Screw 176015-112 #10 x 3%4-Inch Cross-Recessed Pan-Head Screw 176021-004 #8 x %-Inch Zinc Hex Washer-Head Screw (Acceptable substitute is part no. 176021-104) 178120-206 0.375-Inch PCB Support (located between the Main and Analog Vector-Generator PCB) 178120-212 %-Inch PCB Support 178140-2612 ¥4-Inch PCB Spacer

5-27

Page 68

Illustrated Parts Lists Star Wars

040722-01 Spacer A038463-21 Analog Vector-Generator PCB See Figure 5-13

A040472-01 Interconnect Cable

178140-2612 PCB Spacer

72-1606S

178120-206 Poo Supper TEIMOAF A038461-21 Main PCB See Figure 5-12

‘A040725-01 Housing & Tray Assembly

T21604F 040723-01 Screw Housing A040255-01 Interconnect PCB

A040260-21 Sound PCB See Figure 5-14 176015-112 Screw

176021-004 Screw

Regulator/Audio Il PCB See Figure 5-11 034536-02 Analog Vector-Generator PCB 3 7 Foam Pad See Figure 513, — ee

A040301-01 178047-032 Tray and Guides Assembly Guid 7

See Figure 5:12 \g Tray

Figure 5-9B PCB Mounting Hardware Ireland-Built Cabinet

5-28

Page 69

Star Wars, illustrated Parts Lists

PCB Mounting Hardware Ireland-Built Cabinet Parts List

Part No. Description

A035435-02 Regulator/Audio II PCB A038461-21 Star Wars Main PCB Assembly A038463-21 Stars Wars Analog Vector-Generator (AVG) PCB Assembly A040255-01 Stars Wars Interconnect PCB Assembly A040260-21 Stars Wars Sound PCB Assembly A040472-01 Interconnect Cable

A040725-01 Tray and Guides Assembly—includes: 4040301-01 Mounting Tray and Guides for Regulator/Audio II PCB—includes: 040300-01 Mounting Tray 178047-022 il-Inch Snap-In PCB Guide (two required) A040724-01 PCB Guide Assembly—includes: 040723-01 PCB Housing 178047-032 16-Inch Snap-In PCB Guide (four required) 176021-004 #8 x %-Inch Zinc Hex Washer-Head Screw (attaches the Regulator/Audio I! PCB to the mounting tray— acceptable substitute is part no. 176021-104) 72-1604F #6-32 x ‘4 -Inch Cross-Recessed Pan-Head Screw 7216068 #6-32 x %-Inch Pan-Head Screw 034536-02 Foam Pad {not shown) 040722-01 Spacer (not shown) 176015-112 #10 x %-Inch Cross-Recessed Pan-Head Screw 178120-206 0.375-Inch PCB Support (not shown—located between the Main and Analog Vector-Generator PCB) 178120-212 34-Inch PCB Support 178140-2612 %-Inch PCB Spacer

Page 70

Hlustrated Parts Lists Star Wars

NOTICE TO ALI. PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wrirten permissionof Atti, Inc., Sunnyvale, CA. This drawingis only conditionally issued, and neither receipt nor possession thereof confers or transfers anj right in, or license teuse, the subject matter of the drawing or any design or rechnical information shown thereon, nor any sight to reproduce this drawing or any. ‘part thereof. Except for manufacture by vendors of Ari, inc, and for manufactureundes the corporation's writen license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or writien permission from the corporation.

fo) HOU >| orce —_

cee+FY3

c23-f os CS i Cw ceo aoc? 1-c8 oc? cee 4m ECO OC! 12 oie C32 OC i3 C33 C14 c34-—r oci5 o-Cie c 36-0 C17 C37 C39} ta cao (Roca!

C50 -Go+ cs7 fo csear S| C594 C60} C45 F709¢ LO C46 470pF IO C47 47Ope =

Col oo1C48 41Op¢

C2 a> 449 420pr co3 LF C5O 4706 CO4 aT} Oo C52

—GOc55

ez] -CoKC54

cos-irLO}~rrcss

Figure 5-10 EMI Shield PCB Assembly A040258-01 A

5-30

Page 71

Star Wars Iustrated Parts Lists

EMI Shield PCB Assembly Parts List

Part No. Description

Capacitors

Cl-C160.1 #E, + 80% -20%, 50 V, Ceramic Capacitor122002-104
Cl70.01 pF, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103,
C21-C230.1 AE, +80% -20%, 50 V, Ceramic Capacitor122002-104
C260.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C290.1 nF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C31-C340.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C360.01 pF, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103.
C37-C400.1 AF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C45-C50470 pE, 100 V, Ceramic Axial-Lead Capacitor122016-471
C52-C640.1 wE, +80% -20%, 50 V, Ceramic Capacitor122002-104
C680.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104

Connectors

P1930-Pin Edge Connector (Acceptable substitute is part no. 179046-030)179073-030
P2044-Pin Edge Connector (Acceptable substitute is part no. 179046-044)179073-044

Miscellaneous Spacer 037873-02 #4-40 x %4 Cross-Recessed Pan-Head Screw 72-1404F ¥%-Inch Grommet 178044-242 %-Inch White Plunger 178045-442 Flat Nylon Washer 175009-221

5-31

Page 72

Illustrated Parts Lists Star Wars

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbxdden without the specific writ fen permission of Alari, Inc. Sunnyvale, CA. This drawing is only cconditionalty issued, and neither receipt nor possession thereof cone fers ortranslers any rightin, or lense to use, the subject matter of ‘the drawing or any design or technicalinformation shown thereon, 1oF any rightto reproduce this drawing or any part thereat. Except formanulacture by vendors of Alan, Ine, and for manufacture under the corporation's witten license, no rights granted to reproduce this, ‘drawing orthe subject matter thereof, uniess by writlen agreement with orwritten permission from the corporation.

CAUTION Minimum clearance between R31 and the PCB surface should be inch.

a Oo 33 5 24,10, 7 fo) a

TIP32_TOAZ002ATDAZ2002A
BaIQ2iNaOOz Q5 nTjlQr

cre op fle 4 + In a AL ee 2) 8 cecaanlS 33)R3 cis ea 2 0 ce R220BS A 4 gy 220] Rel, (/ew|

Boe©cleyb
0zk23Sra470_*
~«Eecen 2yTSIR20
Joa4b4qo
4zc470+EHRIS

Bil Z aera cio

0>3300uF+}—

{220 35V R30 RO 1/2W ce To Nace: 94 iz)

&™—4+3300uF-—
qy235V

Figure 5-11 Regulator/Audio II PCB Assembly A035435-02 H

Page 73

Star Wars Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

Cc470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 wF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 wF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 pF, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is partno.—_-100015-103

122005-103)

C60.22 uF, 25 V, Ceramic-Dise Axial-Lead Capacitor122004-224
C70.001 wF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 wF, 25 V, Ceramic-Dise Axial-Lead Capacitor122004-224
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cil0.1 wE, 50 V, Ceramic-Dise Axial-Lead Capacitor122002-104
cl2470 uF, 25 V, Auminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cla1000 gF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
cla0.01 wF, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.100015-103

122005-103)

cis0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
Cl70.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 wE, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C22, C231 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500)05
C2422 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350226
C3122 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350226

Diodes

CRIType-IN4002, | A, 100 V Silicon Rectifier Diode31-IN4002,
CR4Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002
CR5-CR8Type-1N5401, 3 A, 100 V Silicon Rectifier Diode31-IN5401

Resistors

RI2702, +5%, %& W Resistor110000-271
R333.2, +5%, % W Resistor110000-330
R41002, +5%, % W Resistor110000-101
RS2.79, 45%, 1 W Resistor110009-027
RO3.9kQ, 45%, 4 W Resistor110000-392
R775kQ, +5%, % W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer119002-102
RO2200, +5%, % W Resistor110001-221
RIO10, +5%, 4 W Resistor110000-010
RU102, +5%, % W Resistor110000-100
R121000, +5%, 4 W Resistor110000-101
R13, Rl410k, +5%, % W Resistor110000-103,
R20109, 45%, 4% W Resistor110000-100
R212200, +5%, % W Resistor110001-221
RID1, 45%, 4 W Resistor110000-010
R221002, +5%, % W Resistor110000-101

(Continued on next page)

Page 74

Illustrated Parts Lists Star Wars

Regulator/Audio Il PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R240.10, +3%, 7 W Wirewound Resistor19-100P1015
R2540, +5%, 5 W Wirewound Resistor116001-040
R27, R2B1k&, +5%, 4 W Resistor110000-102
R29, R30109, 45%, 4 W Resistor110000-100
R3122.0, 45%, 10 W Wirewound Resistor116000-220
R32, R33.5.6k0, +5%, 4 W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055

Miscellaneous

j66-Position Connector Receptacle79-58306
79-Position Connector Receptacle79-58308.
384-Position Connector Receptacle79-58354
Jo6-Position Connector Receptacle79-58306
jlo12-Position Connector Receptacle79-58346
Ql5 V Linear Voltage Regulator37-LM305
Q2, Q9Thermaliy Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-16008
QsAudio Amp TDA2002A137151-002
Q7Audio Amp TDA2002A137151-002
QsType-7812 +12 V Voltage Regulator37-7812
Q9Type-7905 ~5 V Voltage Regulator37-7905

Heat Sink 034531-01 Jest Point (Acceptable substitute is part no. 179051-001) 179051-002

5-34

Page 75

" 10 9 8 7 6 5 4 3 2 1

= wi

A038461-21 G Figure 5-12 Main Printed-Circuit Board Assembly m1 Sa ae} Sel fag Gay beer) ear ia SS faa

gees) ’ Aar52

ve) ae rere] herr} sos} ts) Sawa) fee) Sea ee ee Se) fers) te) Seal SSE] es] es} Sg

  • Ge) 8) fa Se Ss =

5-35

NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING with or writen permission fram the corporation,

Star Wars

oe i Iiustrated Parts Lists

Page 76

Illustrated Parts Lists

Main Printed-Circuit Board Assembly Star Wars.

Parts List

DesignatorDescriptionPart No.

Capacitors

cl0.1 pF, £5%, 50 V Ceramic Capacitor122002-104
C2100 pk, 100 V Mica Capacitor128002-101
C339 pE, 100 V Mica Capacitor128002-390
C4-€22O.1 E,+5%, 50 V Ceramic Capacitor122002-104
C45~-C480.1 uF, 45%, 50 V Ceramic Capacitor122002-104
C49-C510.100 uF, 35 V Electrolytic Capacitor(Acceptable substitute is part no.24-350107

124001-107)

C52-C920.1 pF, +5%, 50 V Ceramic Capacitor122002-104
C930.10 pF, 35 V Electrolytic Capacitor24-350106
C944.7 pF, 35 V Electrolytic Capacitor24-500475
C95, C960.1 pF, +5%, 50 V Ceramic Capacitor122002-104

Diodes

CRIType-INO14 Diode31-IN914
CR2Red Light-Emitting Diode38-MV5053
CR3Type-IN914 Diode3LIN914
CR4—-CR6Red Light-Emitting Diode38-MV5053

Integrated Circuits

VRI5 V Fixed Regulator Integrated Circuit37-7805
OBIC3-8 Line Decoder Integrated Circuit137177-001
OD/IETri-State Octal Bus Transceiver Integrated Circuit37-7418245
IBLine Driver/Receiver Integrated Circuit377418244
ICLine Driver/Receiver Integrated Circuit37-74L8244
1ENonVolatile RAM Integrated Circuit137288-001
IF300 ns EPROM Integrated Circuit136021-114
1H300 ns Tri-State EROM Integrated Circuit136021-102
WK300 ns Tri-State EROM Integrated Circuit136021-203
1K/L300 ns Tri-State EROM Integrated Circuit136021-104
IM.300 ns Tri-State EROM Integrated Circuit136021-206
INQuad 2-Input NOR Gate Integrated Circuit37-74804
2cMicroprocessor137249-120
2E/FLine Driver/Receiver Integrated Circuit37-74LS244
26/H150 ns Tri-State Static RAM Integrated Circuit137211-001
2Dual 2-4 Decoder/Multiplexer Integrated Circuit37-74LS139
2KHex Inverter Integrated Circuit37-74LS08
2L3-8 Line Decoder Integrated Circuit137177-001
2MDual D-lype Flip-Flop Integrated Circuit37-74LS74
2N4-Bit Counter Integrated Circuit37-7ALSIOL
2pDual 4-Bit Bin Counter Integrated Circuit37-74LS393
2RDual 4-Bit Bin Counter Integrated Circuit37-74L8393
3DUp-Down Counter Integrateduit37-74LS191
3EUp-Down Counter Integrated Circuit37-74LS191

(continued on next page)

Page 77

Star Wars Illustrated Parts Lists

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPartNo.
3FUp-Down Counter Integrated Circuit37-7ALSI91
3HQuad Data Selector/Multiplexer Integrated Circuit37-74LS8157
3)Data Selector/Multiplexer Integrated Circuit37-7ALSIS3
3KData Selector/Multiplexer Integrated Circuit37-74LS153
3LQuad Data Selector/Multiplexer Integrated Circuit37-7ALSIS7
3MType-74LS00 Integrated Circuit37-74LS00
3NShift/Storage Register Integrated Circuit137180-001
3PQuad 2-Input NOR Gate Integrated Circuit37-TALSO4
3R4-Bit Counter Integrated Circuit37-74LS161
4DShift/Storage Register Integrated Circuit137180-001
4E‘Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245
4FTri-State Octal Bus ‘Transceiver Integrated Circuit37-7ALS245
4H‘Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245
4Line Driver/Receiver Integrated Circuit37-74LS244
4KLine Driver/Receiver Integrated Circuit37-74LS244
4L, SLOctal D-lype Flip-Flop Integrated Circuit37-74LS374
4M, 5MOctal D-Type Flip-Flop Integrated Circuit37-74LS374
4N-ON4-Bit Counter Integrated Circuit37-74LS83
4P-6PQuad D-Type Flip-Flop Integrated Circuit37-7ALSI7S,
SBQuad Exclusive OR Integrated Circuit37-74LS86
5c8-Bit Register Counter Integrated Circuit37-74LSIG4
5D8-Bit Register Counter Integrated Circuit37-74LS104
5E, OEHex Inverter integrated Circuit37-74LS08
SF150 ns Tri-State Static RAM Integrated Circuit137211-001
SH150 ns Tri-State Static RAM Integrated Circuit137211-001
5)8-Bit Register Counter Integrated Circuit37-7ALS164
5K8-Bit Register Counter Integrated Circuit37-TALS164
SRDual l-of-4 Decoder/Multiplexer Integrated Circuit137221-001
6A8-Bit Register Counter Integrated Circuit37-7ALSIOS
6B8-Bit Register Counter Integrated Circuit37-74LS165
6C, 7CTwo's-Complement, Serial Multiplexer Integrated Circuit137182-001
6D, 7DShift/Storage Register Integrated Circuit137180-001
OFData Selector/Multiplexer Integrated Circuit37-7ALSIS3
OHUp-Down Counter Integrated Circuit37-7ALSI9L
OlUp-Down Counter Integrated Circuit37-74LS191
OKHex Inverter Integrated Circuit37-74LS08
OLQuad D-Type Flip-Flop Integrated Circuit3 7-74LS175
OM4-Bit Counter Integrated Circuit37-74LS83
ORDual D-Type Flip-Flop Integrated Circuit37-7ALS7A
7A8-Bit Register Counter Integrated Circuit37-74LS105
7B8-Bit Register Counter Integrated Circuit37-TALS1O5,
TEType-74LS00 Integrated Circuit37-7ALSOO
TFType-74LS00 Integrated Circuit37-74L800
7HROM Integrated Circuit136021110

(continued on next page)

5-37

Page 78

Illustrated Parts Lists Star Wars

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPartNo.
aROM Integrated Circuit136021-111
7KROM Integrated Circuit136021-112
7LROM Integrated Circuit136021-113,
7™MShift/Storage Register Integrated Circuit137180-001
7N3-8 Line Decoder Integrated Circuit137177-001
7Dual D-type Flip-Flop Integrated Circuit37-74LS74
8ADual D-Type Flip-Flop Integrated Circuit37-7ALS74
8BQuad Serial AdderSubtractor Integrated Circuit137181-001
8cHex Inverter Integrated Circuit37-74LS08
8D‘Type-74LS00 Integrated Circuit37-74LS00
8EQuad 2-Input NOR Gate Integrated Circuit37-7402
SF‘Triple 3-Input NAND Gate Integrated Circuiti37236-001
8HDual D:Type Flip-Flop Integrated Circuit37-TALS74
8KQuad 2-Input NOR Gate Integrated Circuit37-7AL804
8L.3-8 Line Decoder Integrated Circuit137177001
8M3-8 Line Decoder Integrated Circuit137177-001
8N‘Type-74LS00 Integrated Circuit37-74LS00
8PDual J-K Flip-Flop Integrated Circuit37-74LS109
8RUp-Down Counter Integrated Circuit37-74LS191
9A8-Bit Register Counter Integrated Circuit37-TALSIO4
9B8-Bit Register Counter Integrated Circuit37-74LS104
9C, 10C4-Bit Counter Integrated Circuit37-7A4LS161
9D4-Bit Counter Integrated Circuit37-7ALSIG1
oFLine Driver/Receiver Imegrated Circuit-TALS244
oFLine Driver/Receiver Integrated Circuit37-TALS244
9HLine Driver/Receiver Integrated Circuit37-T4LS244
oyLine Driver/Receiver Integrated Circuit37-74L8244
9KAnalog/Digital Converter Integrated Circuit137243-001
OL/M8-Bit Latch Integrated Circuit37-74L8259
10LHex Buffer/Driver Integrated Circuit37-7407
10RHex Inverter Schmitt Trigger Integrated Circuit377ALSI4
MNDual Operational Amplifier Integrated Circuit37TLO82CP

Resistors

Ri, R210kQ, 45%, % W Resistor110000-103
R32200, +5%, 4 W Resistor110000-221
R41kQ, +5%, 4 W Resistor110000-102
RSWOR, 45%, 4 W Resistor§10000-103
RO100 kQ, +5%, 4 W Resistor110000-104
R72202,5%, % W Resistor110000-221
RB15 kQ, +5%, % W Resistor110000-153
R9, RIO1kQ, +5%, 4 W Resistor110000-102
R11, R1210kQ, +5%, 4% W Resistor110000-103
Ri3, R142200, +5%, % W Resistor110000-221
RIS10 kQ, 5%, % W Resistor110000-103

(continued on next page)

5-38

Page 79

Star Wars Illustrated Parts Lists

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R16, RI71kQ, +5%, 4 W Resistor110000-102
RI8-R214700, +5%, 4 W Resistor410000-471
R22-R251kQ, +5%, 4 W Resistor110000-102
R26-R334700, +5%, 4 W Resistor410000-471
R34-R411kQ, 5%, % W Resistor110000-102
R42-R5710 kQ, 45%, 4 W Resistor110000-103
R582202, +5%, % W Resistor110000-221
R79-R811002, +5%, 4 W Resistor110000-101
R82-R864.7k®, +5%, %& W Resistor110000-472
ROL150.0, +5%, %4 W Resistor110000-151
R92-R971kQ, +5%, 4 W Resistor110000-102
RIOO22 kQ, 5%, % W Resistor110000-223,

Sockets

1E18 Contact, Medium, Insertion-Force IC Socket79-42C18
IF28 Contact, Medium-Insertion-Force IC Socket79-42C28
1Hh28 Contact, Medium-Insertion-Force IC Socket79-42C28
WK28 Contact, Medium-Insertion-Force IC Socket79-42C28
IK/L28 Contact, Medium-Insertion-Force IC Socket79-42C28
1M28 Conuct, Medium-Insertion-Force IC Socket79-42C28
2c40 Contact, Medium-Insertion-Force IC Socket79-42C40
2F/H24 Contact, Medium-Insertion-Force IC Socket79-42024
5E24 Contact, Medium-Insertion-Force IC Socket79-42C24
SH24 Contact, Medium-Insertion-Force IC Socket79-42C24
JH48 Contact, Medium-Insertion-Force IC Socket79-42C18
vA18 Contact, Medium-Insertion-Force IC Socket79-42C18
7K18 Contact, Medium-Insertion-Force IC Socket79-42C18
7L18 Contact, Medium-Insertion-Force IC Socket79-42C18
9K28 Contact, Medium-Insertion-Force IC Socket79-42C28

Switches

10D8Toggle DIP Switch66-118PIT
OE8-Toggle DIP Switch66118PIT
iL4Toggle DIP Switch6G-114PIT

Transistors

qu‘Type-2N3904 Transistor34-2N3904
3, Q4Type-2N6044 Transistor34-2N6044

Miscellaneous Test Point Acceptable substitute is part no. 020670-01 179051-002

Li100 #H, +5%, Fixed RF InductorAcceptable substitute is part no. 141002-00141-3003
JIGA2-Contact Header Connector79-58255
JOB4-Contact Header Connector79-58331
Q3Nylon Snap-in Fastener81-4302
QtNylon Snap-In Fastener81-4302
VRINylon Snap-in Fastener81-4302
Yl12.096-MHz Crystal144000-001

5-39

Page 80

Star Wars Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

I) Oe fies fice = ea aed] ' ei] user] see] re sn) Seq aa} [S42) cara hse] . 2 = ey Unser ese? Eres a a s ge re 4 cm cease Saal =e) za "ee og, Sz t= _ = __" fag a be vee at 9 ee ons Oz]

MW t Q Fens

1 1 = Gas Samed) asa] 2a Cara] been

Leo is ed pes] =] =] Ces [S20 =) eazaa

fe es] Le HOOPS.) tye ieee Ne) ETE) ghee N ey

Figure 5-13 Analog Vector-Generator (AVG) PCB Assembly A038463-21 D

5-40

Page 81

Star Wars. Illustrated Parts Lists

Analog Vector-Generator (AVG) PCB Assembly Parts List

DesignatorDescriptionPartNo.

Capacitors

CI-C30.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-164
C4, C50.01 wF, 100 V Mylar Capacitor21-101103
C6, C70.1 AF, +80% -20%, 50 V Ceramic Capacitor122002-104
c80.047 pF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-473
C9-C120.1 4F, +80% -20%, 50 V Ceramic Capacitor122002-104
Cl40.1 uF, +80% -20%, 50 V Ceramic Capacitor122002-104
C17-C200.1 AF, +80% -20%, 50 V Ceramic Capacitor122002-104
C210.01 pF, 100 V Mylar Capacitor21-101103
C250.047 pF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-473
C26-C28O.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C3O.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C35, C360.1 #F, +80% -20%, 50 V Ceramic Capacitor122002-104
C37150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C3839 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
39, C400.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
CAl0.01 pF, 25 V Ceramic Capacitor122005-103
4210 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-100
C43, C44100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C4522 wE, 25 V, Aluminum Electrolytic Axial-Lead Capacitor24-250226
C46100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
CAT150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C4822 pF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor24-250226
C50~C6S0.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C66150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C67-C800.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
c8l100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C820.1 pE, +80% -20%, 50 V Ceramic Capacitor122002-104
C8322 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-220

Coils

LI-L3830 mA, 0.29, +£10%, 1.0 wH, Peaking Coil Inductor141007-.001

Diodes

CRIType-IN914 Diode31-IN914
CR2Type-MV5053 Red Light-Emitting Diode38-MV5053
CR3, CR4Type-IN100 Diode3L-IN100

Integrated Circuits

1AQuad 2-Input AND Gate Integrated Circuit37-74LS08
1B4-Bit Counter Integrated Circuit37-7ALSI1O1
IC4-Bit Counter Integrated Circuit37-7ALSIOL
ID4-Bit Counter Integrated Circuit37-74LSI61
1EQuad 2-Input NOR Gate Integrated Circuit37-74LS02
IF‘Triple 3-Input NOR Gate Integrated Circuit37-74LS27
1HDual D-Type Flip-Flop Integrated Circuit37-TALS74
IK‘Tri-State Octal Bus Transceiver Integrated Circuit37-7418245,

(continued on next page)

Page 82

Illustrated Parts Lists Star Wars

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
ILRead-Only Memory Integrated Circuit136021-105
1MLine Driver/Receiver Integrated Circuit37-TALS244
INLine Driver/Receiver Integrated Circuit37-74LS244
IPLine Driver/Receiver Integrated Circuit37-74LS244
2ADual 4-Input NAND Gate Integrated Circuit37-74L826
2B4-Bit Counter Integrated Circuit37-74LSI61
2cTriple 3-Input Positive AND Gate Integrated Circuit137149-001
2DDual D-lype Flip-Flop Integrated Circuit37-74LS74
2EQuad 2-Input OR Gate Integrated Circuit37-74LS32
2FDual J-K Flip-Flop Integrated Circuit37-74109
2HQuad 2-Input AND Gate Integrated Circuit37-74LS08
2Vector-Generator Integrated Circuit137179-001
2K4 to 10 Decoder Integrated Circuit37-TALS42
2MLine Driver/Receiver Integrated Circuit37-7418244
2NLine Driver/Receiver Integrated Circuit37-74LS244
3AQuad 2-Input NAND Gate Integrated Circuit37-74LS00
3BHex D-Type Flip-Flop Integrated Circuit37-7ALS174
3CQuad D-Type Flip-Flop Integrated Circuit37-7ALSI7S
3D4 to 10 Decoder Integrated Circuit37-7ALS42
3EQuad 2-Inpat NOR Gate Integrated Circuit37-74802
3F745260 integrated Circuit37-745260
3HQuad 2-Input NOR Gate Integrated Circuit37-74L802
3L150 ns Tri-State Static RAM Integrated Circuit137211-001
3M150 ns Tri-State Static RAM Integrated Circuit137211-001
3P150 ns Tri-State Static RAM Integrated Circuit137211-001
4AQuad Data Selector/Multiplexer Integrated Circuit37-7ALSIS7
4BRead-Only Memory Integrated Circuit136021109
4cQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
4DHex, Schmitt/Trigger Integrated Circuit37-74LS14
4EQuad 2-Input NAND Gate Integrated Circuit37-74S00
4FQuad 2-Input Exclusive-OR Gate Integrated Circuit137002-001
4HQuad DType Flip-Flop Integrated Circuit37-74LS175,
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4M150 ns Tri-State Static RAM Integrated Circuit1372-001
4P150 ns Tri-State Static RAM Integrated Circuit137211-001
SAShift Register Integrated Circuit37-7ALS194
5BShift Register Integrated Circuit37-TALSI94
5CShift Register Integrated Circuit37-7ALS194
SEOctal D‘Type Flip-Flop Integrated Circuit37-74LS273,
SFShift Register Integrated Circuit37-TALSI94
SHShift Register Integrated Circuit37-7ALS194
syQuad 2-Input OR Gate Integrated Circuit37-7ALS32
5KDuai D-Type Flip-Flop Integrated Circuit37-TASTA

5-42 (continued on next page)

Page 83

Star Wars Illustrated Parts Lists

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
SLQuad D‘Type Flip-Flop Integrated Circuit37-74LS175,
5MQuad DType Flip-Flop Integrated Circuit37-74LS175
5PHex Inverter Integrated Circuit37-74804
GOAIB12-Bit D-A Converter, Integrated Circuit137158-002
6D8-Bit D-A Converter, Integrated Circuit137159-001
GE12-Bit D-A Converter, Integrated Circuit137158-002
OFOctal D‘Type Flip-Flop Integrated Circuit37-74L8273
GHShift Register Integrated Circuit37-74LS194
6‘Triple 3-Input NAND Gate Integrated Circuit137236-001
6KHex Inverter Integrated Circuit37-74LS04
6LQuad D-Iype Flip-Flop Integrated Circuit377418175
OMUp/Down Counter Integrated Circuit37-74LS191
7ADual Operational Amplifier Integrated Circuit37-TLO82CP.
7BLF13201 Quad Analog Switch, Integrated Circuit3713201
7DDual Operational Amplifier Integrated Circuit37TLO82CP
JELF13201 Quad Analog Switch, Integrated Circuit3713201
8BICDual Operational Amplifier integrated Circuit37TLOB2CP
8F8-Bit D-A Converter, Integrated Circuit137159-001
8LHex Buffer/Driver Inverter Integrated Circuit37-7407
8MQuad 2-Input NOR Gate Integrated Circuit37-74LS02
8N8-Bit Register Counter Integrated Circuit37-74LS164
9OBICDual Operational Ampiifier Integrated Circuit377L082CP
OFDual Operational Amplifier Integrated Circuit37-TLOB2CP
VRI1A, 15 V, Fixed Regulator Integrated Circuit37-7815
VR21A, -15 V, Fixed Regulator Integrated Circuit37-7915

Resistors

RERIO10kQ, +5%, % W Resistor110000-103
RU12 kQ, 45%, ‘4 W Resistor110000-123
RIZ24kQ, +5%, ‘4 W Resistor110000-243,
R1347kQ, £5%, 4 W Resistor110000-473
R148200, +5%, 4 W Resistor110000-821
R15100 kQ, +5%, 4 W Resistor110000-104
R1612 kQ, +5%, %& W Resistor110000-123
RI76.2 kQ, +5%, 4 W Resistor110000-622
R20-R224700, +5%, % W Resistor110000-471
R23-R254.7kQ, 5%, % W Resistor110000-472
R268200, +5%, % W Resistor110000-821
R278200, +5%, 4 W Resistor110000-821
R30, R3175kQ, 41%, % W Resistor110003-752
R4l10 kQ Potentiometer119002-103
R42150 kQ, +5%, 4 W Resistor110000-154
R43,2.7kQ, +5%, % W Resistor110000-272
R4410 k@ Potentiometer119002-103
R456.8 kO, 45%, 4 W Resistor110000-682
R4622kQ, +5%, % W Resistor110000-223
R472 kQ Potentiometer119002-202

(continued on next page)

Page 84

Alustrated Parts Lists

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued Star Wars

DesignatorDescriptionPart No.
RSI1002, +5%, % W Resistor110000-101
R548202, 45%, 4 W Resistor110000-821
RSS320 2, +5%, % W Resistor110000-821
R587.5 kQ, 41%, % W Resistor110003-752
ROS.10 k@ Potentiometer119002-103
R69150 kQ, 45%, % W Resistor110000-154
R702.7 kQ, +5%, % W Resistor110000-272
R7110 kQ Potentiometer119002103
R726.8 kN, +5%, % W Resistor110000-682
R7322 kQ, 25%, 4 W Resistor110000-223,
R74.2 kQ Potentiometer419002-202
R75, R701,3 kQ, +1%, % W Resistor110000-132
R78100 2, +5%, % W Resistor410000-101
R8i15 kQ, +5%, 4 W Resistor110000-153
R82A kQ, +1%, “ W Resistor110000-102
R8310K, £5%, 4 W Resistor110000-103
R84560 2, +5%, % W Resistor110000-561
R85, R86.7.5kQ, +1%. % W Resistor110003-752
R876.19 kQ, 41%, % W Resistor110003-622
R88200 @ Potentiometer119002-201
R8975k, +1%, % W Resistor110003-752
ROO1000, +5%, 4 W Resistor110000-101
ROL6.19kO, £1%, 4 W Resistor110003-622
R92200 © Potentiometer119002-201
R9325kQ, +1%, % W Resistor110003-752
RO4100.0, +5%, 14 W Resistor110000-101
ROS, ROG7.5kO, +1%, % W Resistor110003-752
RIT3.9kQ, +5%, % W Resistor110000-392
R98-R105100 kQ, 45%, 4 W Resistor110000-104
R10675 kM, +1%, & W Resistor0003-752
R1071500, +5%, 4 W Resistor110000-151
R1O9-RIIL1kQ, £1%, % W Resistor110000-102
R12, RU310 kQ, +5%, 4 W Resistor1100004103
Ril4-R11G,1000, +5%, % W Resistor110000-101
RU710 kQ, +5%, 4 W Resistor110000-103
RVI, RV28 V Variable Resistor110604-001
VRi, VR2Nylon Snap-In Fastener81-4302

Sockets IL 24 Contact, Medium-Insertion-Force IC Socket 2y 40 Conwact, Medium-Insertion-Force IC Socket

3L24 Contact, Medium-Insertion-Force IC Socket74
3M24 Contact, Medium-Insertion-Force IC Socket79-42C24
3P24 Contact, Medium-Insertion-Force IC Socket79-42024
4L24 Contact, Medium-Insertion-Force 1C Socket79-42C24
4M24 Contact, Medium-Insertion-Force IC Socket79-42C24
4P24 Conuct, Medium-Insertion-Force IC Socket79-42C24

Transistors

QlType-2N3904 Transistor34-2N3904
Q4-Q7‘Type-2N3904 Transistor34-2N3904
Q8‘Type-2N3906 Transistor34-2N3906

Miscellaneous ‘Test Point 179051-002

5-44

Page 85

Illustrated Parts Lists Star Wars

  • —_ L L_ 10) ie) “wSN Ni JaVW £861) 5 a [a] ,38 wvby = a “a8 GNNOS SYVM HV¥LS #2 0 . * aul 4 =

S88 w SSR SSE x we S et Fats

2p nl 8 9

} 20 O Ls & lla a of. ys cw per wu c f ibe

ee —™ LU oo a - 5 om

‘ ope: oy OL? an Few 8 fd ° ae — yy 40 U x Be » Ws} Ws |} 3 “

wo. t— wo wo 5D oft} d Ta ee alo

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

(@) CONFIDENTIAL: Reproduction forbidden without the spect wrt

ten permission of Alar, Inc, Sunnyvale, CA. This drawings only

formation shown thereon, jor any part thereat. Except

‘and for manufacture under

ight’S granted to repeaduce this

cf, unless by written agreement

the Corporation. with or written peri

5-45 Figure 5-14 Sound PCB Assembly A4040260-21 C

Page 86

Mlustrated Parts Lists Star Wars

Sound PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl-c12O.1 pF, 50 V, Ceramic Capacitor122002-104
Ci3-C15100 wF, 35 V, Aluminum Electrolytic Capacitor24-350107
C16-€200.4 aE 50 V, Ceramic Capacitor122002-104
€22-€280.1 pF, 50 V, Ceramic Capacitor122002-104
C291000 pF, 50 V, Monolithic Ceramic Capacitor122002-102
€30-C320.1 w¥, 50 V, Ceramic Capacitor122002-104
C331000 pE, 50 V, Monolothic Ceramic Capacitor122002-102
C340.1 wE, 50 V, Ceramic Capacitor122002-104
C351000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
C36-C380.1 pk, 50 V, Ceramic Capacitor122002-104
C391000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
€40-C43,0.1 pE, 50 V, Ceramic Capacitor122002-104
C440.01 pF, 25 V, Ceramic Capacitor122005-103,
cas0.1 #E, 56 V, Ceramic Capacitor122002-104
C460.0027 wE, 50 V, Ceramic Capacitor122015-272
C4?100 wF, 35 V, Aluminum Electrolytic Capacitor24-350107
C48-C500.0027 uF, 50 V, Ceramic Capacitor122015-272
CSI0.47 pF, 50 V, Aluminum Electrolytic Axial-Lead Capacitor124001-474
cs210 p25 V, Aluminum Electrolytic Capacitor24-250106
C53109 pF, 35 V, Aluminum Electrolytic Capacitor24-350107
C54, C55,0.1 pF, 50 V, Ceramic Capacitor122002-104
C56-C580.0027 wE, 50 V, Ceramic Capacitor122015-272
C59-C610.1 wk, 50 V, Ceramic Capacitor122002-104

Connectors

P24-Contact Headet-Connector479165-004
P32-Contact Header-Connector179165-002

Diodes

DSIType-MV5053 Red Light-Emitting Diode38-MV5053

Integrated Circuits

1c/DSpeech Synthesizer Integraied Circuit137308-001
IE1/Q and Internal Timer Memory Integrated Circuit90-6018
IH150 ns Tri-State Static RAM Integrated Circuit1372-001
14ROM Integrated Circuit136021-208
WKROM Integrated Circuit136021-107
2BQuad Operational Amplifier Integrated Circuit37-347
2Audio Integrated CircuitCO12294-01
2FType-74C04 Integrated Circuit137309-001

2H Type-74L804 Integrated Circuit

  • ‘Type-74LS139 Integrated Circuit 3A ‘Type-556 Integrated Circuit
3B512 Delay Line integrated Circuit137310-001

(continued on next page)

Page 87

Star Wars Mtustated Parts Lists

Sound PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
3CQuad Operational Amplifier integrated Circuit37347
3DAudio Integrated CircuitCO12294-01
3F‘Type-74LS16] Integrated Circuit37-741S161
3HType-741S00 Integrated Circuit37-7ALSOO
3‘Type-7415139 Integrated Circuit37-7ALS139
3KMicroprocessor137249-120
4cQuad Operational Amplifier Integrated Circuit37347
4DAudio Integrated Circuit€O12294-01
5DAudio Integrated CircuitCO12294-01
SE‘Type-74LSI6L Integrated Circuit37-74LS161
SFI‘Type-741S125 Integrated Circuit137317-001
SH‘Type-74LS74 Integrated Circuit37-TALST4
By‘Type- 7415374 Integrated Circuit37-74LS374
5K‘Type-74LS374 Integrated Circuit37-7ALS374

Resistors

RI1KQ, +5%, %& W Resistor110000-102
R2, R310 kO, +5%, % W Resistor110000-103,
R4LkQ, +5%, 4 W Resistor110000-102
RS, R610 kQ, +5%, % W Resistor110000-103
R71500, +5%, ‘4 W Resistor110000-151
R1010 kQ, +5%, 4 W Resistor110000-103
Ril3.3kQ, +5%, 4 W Resistor110000-332
Ri21kQ, +5%, & W Resistor110000-102
R1310kQ, +5%, %& W Resistor110000-103,
Rid3.3 kQ, +5%, 4 W Resistor0000-332
RIS1kQ, +5%, 4 W Resistor110000-102
RI63.3kQ, +5%, % W Resistor110000-332
RIT10k, +5%, % W Resistor110000-103,
RI81.8kQ, +5%, 4 W Resistor110000-182
R19100 k2, +5%, 4 W Resistor110000-104
R201kQ, +5%, 4 W Resistor110000-102
R2147 KO, +5%, % W Resistor110000-473
R221k®, +5%, 4 W Resistor110000-192
R2347kQ, +5%, 4 W Resistor110000-473,
R241kQ, +5%, 4 W Resistor110000-102
R25,82 kQ, +5%, 4 W Resistor110000-823
R261kQ, +5%, 4 W Resistor110000-102
R2782 kQ, +5%, ‘4 W Resistor116000-823,
R28100 Kk, 45%, 4 W Resistor110000-104
R2915kQ, 45%, & W Resistor110000-153
R3012kQ, 5%, % W Resistor110000-123
R31, R32560 kQ, +5%, 4 W Resistor110000-564
R33, R344.7 kQ, +5%, %& W Resistor110000-472

(continued on next page)

5-47

Page 88

Illustrated Parts Lists Star Wars

Sound PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R35,2.2kQ, +5%, 4 W Resistor110000-222
R36150, +5%, % W Resistor110000-150
R3710 kQ, +5%, 4 W Resistor110900-103,
R38470 0, +5%, % W Resistor110000-471
R39, R4012 kQ, +5%, 4 W Resistor110000-123
R4168 kQ, +5%, 4 W Resistor110000-683
R4212 kQ, +5%, 4 W Resistor110000-123
R431.5k@, +5%, % W Resistor110000-152
R44100 2, +5%, %& W Resistor110000-101
R45470 kQ, 5%, 4 W Resistor110000-474
R46, R4712 kQ, +5%, 4 W Resistor110000-123
R48, R4922 kQ, +5%, 4 W Resistor110000-223
R5047kQ, +5%, % W Resistor110000-473
R512.2, £5%, % W Resistor110000-222
R52, R5322 kQ, +5%, % W Resistor110000-223
R54, R5547kQ, +5%, % W Resistor110000-473
R562.2kM, +5%, 4 W Resistor110000-222

Sockets

1cD28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
1E40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
1E/H24-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C24
1H28-Conaact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
W/K28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
2D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3K40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
4D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
sD40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40

Transistors

QI, Q2‘Type-2N3906 Transistor33-2N3906
Q3,Q4Type-2N3904 Transistor34-2N3904

Miscellaneous

TPI-TPI2Z‘Test Point179051-002

5-48

Page 89

Star Wars

AC Alternating current; from zero it rises to amaximum positive level, then passes through zero again to a maximum negative level ACTIVE STATE The true state of a signal. For example: ‘The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mounta pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a micro- Processor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING

Turning off the beam on a cathode-ray

tube during retrace. Glossary

Glossary of Terms

BLOCK DIAGRAM ‘A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting, BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations, CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A G-digit electromechanicat device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, such as the out puts of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a sit gle signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. Dc Direct current, meaning current flowing in one direction and of a fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, Capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that by-

passes the microprocessor logic. DMA

is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used ina display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal.

gil

Page 90

Glossary

HARNESS Aprefabricated assembly of insulated wires and terminals ready to be attached toa piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may Or may not respond. LED ‘The abbreviation for a light-emitting diode.

LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of alogic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0VDC to +0.8VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +24 VDC to +5 VDC

MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultanous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannotignore this interrupt request PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data, These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board.

gl-2 PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • Aninstrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning. the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam,

RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR Adevice designed to have a definite amount of resistance, Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults atthe component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature tead by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues untila fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates ona cathode-ray tube. Star Wars

WATCHDOG A counter Circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-¥ DISPLAY A display system whereby images are displayed with veciors. ZENER DIODE A special diode used asa regulator. Its main characteristic is breaking down at a specified reverse bias (Zener) voltage.

Page 91

Star Wars 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person,

Page: Comments:

Fill in if you wish a reply

Name

Firm C1 Distributor

Address 2 Operator

City State zip 0 Other

Area Code Phone

Page 92

First Fold

No postage necessary if mailed in the United States

USINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086

wos

a8po spp dey,

Page 93

Star Wars 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm O Distributor

Address O Operator

City _. Country O Other

Phone: Country Cede Local Number _.

Page 94

First Fold

Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland

Second Fold

word

a8po spp adey,

Page 95

Warranty

Seller warrants that its printed- Me and parts thereon are free from defects in material and workmanship under normal usé-and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller’s plant; and (c)Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages, Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atati parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. Pek 2k Ba BE RS RN Re RES Pe Ze SS ES EE ES EIS

Page 96

ATARI ATARI, INC. 790 SYCAMORE DRIVE: . P.O. BOX 906 “MILPITAS, CALIFORNIA 95035 . 408/942-3300 ¢ TELEX 35-7488.