CATHODE RAY TOMES

Video Pool

U.S. Billiards Video Pool (U.S. Billiards, Inc.) · Manual · 10 pages · 8 sections · original scan

Page 1

_ Instruction Manual

& Parts Catalog

UWS. BiliRarcls |

VIDEO POOL

——_J.S. Billiards, Inc. = (516) 842-4242

Page 2

A.COMPONENT REMOVAL INSTRUCTIONS

  • TO REMOVE P.C. LOGIC BOARD

Open rear door (power will automatically go off by action of “California Switch”) and remove the 2 screws that hold the wooden bracket to the small logic board. Disconnect the edge connector at the far side of the large P.C. board and both logic boards will now slide out of the wooden receiver

2.TO REMOVE 5 VOLT POWER SUPPLY ASSEMBLY

Disconnect AC cord from outlet and open rear door, The power supply is located at the back right side. Unsolder the Red and Black wires at the top of the unit (left terminal is + Red wire, right terminal is — Black wire). Remove protective plastic cover under which the fuse block and barrier terminal strip are located. Disconnect the 6 wires on the right side of the barrier terminal strip. Remove the 6 screws that secure the complete board assembly to the cabinet. Unsolder the 2 wires going to the California door switch (common and N.O.). Unit can now be completely removed from cabinet.

3.TO REPLACE FUSES

There are a total of 5 fuses in this game. To insure extra reliability and protection of components, 3 fuses are on the Motorola monitor. Two of these are 1 amp Slow-Blow type located at the lower left side of the monitor. The other fuse is a 7 amp Slow-Blow type and is soldered to the terminal strip between the monitor power transformer and the circuit board. The remaining 2 fuses are located under the protective plastic cover on the power supply assembly (back right side of the cabinet). These are 2 amp and 5 amp Slow-Blow fuses, CAUTION — UPON REPLACING ANY FUSE, MAKE CERTAIN THE CORRECT FUSE VALUE IS USED OR DAMAGE TO COMPONENTS MAY OCCUR.

  • TO REMOVE TV MONITOR

Open rear door and disconnect harness connector at lower left corner of the monitor. Remove 2 screws on metal shipping bracket which is located ‘on the right hand side toward the rear and under the monitor mounting panel. TV mounting panel will now slide out

  • TO REMOVE FRONT SWITCH PANEL

Remove AC cord from power and open the front door. Reaching in from the door there is a single wing nut at each end of the switch panel Remove the nut and the panel will lift straight up and out of the groove. On

Page 3

the left side of the panel there is a connector to disconnect. On the right side, reach down approximately one foot to disconnect a connector on that side. The panel can now be removed from the game. To change lamps in the switches, grasp the black lens body portion of the switch on the back side of the panel and push forward firmly. The lamp will now be in view and can be removed by gently grasping with pliers and pulling forward. Should the engraved lens need to be removed, simply push it out from the rear of the black lens body. Re-insert from the front. To remove one of the sets of switches, remove the screws securing the switch assembly bracket to the panel, pull off the black lens body, remove the ‘‘C” clip, spring and black spacer on front of the switch. Bend back the bracket tabs upward and remove switch from rear of the bracket.

  • TO REMOVE PLASTIC PLAYFIELD FROM CABINET

Remove AC cord from power and open front door, Reaching in from the door there is a single wing nut at each end of the switch panel. Remove the nut and lift the panel straight up and out of the groove. From under the playfield panel, gently push up and pull toward you.

  • TO REMOVE HEADER LIGHT PANEL AND SHADOW BOX

To replace header lights, fluorescent and speaker, first unplug AC power, then remove the 4 slotted screws on the top of the cabinet. Remove the upper aluminum ‘‘L”’ bracket and lift the plastic header screen straight up. The game select lamps and fluorescent are now visible. To replace speaker, gently tilt top of shadow box forward and out, enabling access to the speaker.

B. ADJUSTMENTS

  • TO ADJUST TV MONITOR

From the rear of the cabinet, the various controls are facing down, From left to right they are: Contrast, Brightness, Vertical Hold, Horizontal Hold and Volume.

  • TO ADJUST EXTERNAL 5 VOLT POWER SUPPLY

The power supply, located in the lower right corner of the cabinet, as viewed from the rear, is the +5V source for the logic board. This supply is adjusted at the factory. However, if flickering of the balls or rolling of the playfield is experienced, then turn the potentiometer, on the top of the supply, slightly counterclockwise. Recheck and adjust in this manner.

  • RESETTING OF THE LOGIC BOARD

On initial power turn on, a hum will be heard for approximately

Page 4

3 seconds. Should this hum continue, then unplug power and re-insert. Continue until hum disappears after 3 seconds. This insures that the logic board has reset and is synchronized.

  • GAME ADJUSTMENT

Located on the large logic board toward the harness edge connector (far end as viewed from the rear of the cabinet) are 2 slide switches. The position of these switches determines the amount of time the game will play. See chart below for adjustments and time. (Switch 1 is on the right as viewed from the rear. UP designates toward the front of the cabinet)

TIME IN MINUTES

ONE COIN TWO COINS SWITCH POSITION 1PLAYER (40PERIOD) | 2PLAYERS (90 PERIOD)

; oa 14 Minutes 2% Minutes jown

; i 1% Minutes 3% Minutes ; ae 2 Minutes 4% Minutes 7 i 2h Minutes 5% Minutes

Time is set at the factory as follows:

1 Player - one coin - 40 units of time + 2 minutes 2 Players - two coins - 90 units of time + 4% minutes (Switch 1 = Down, Switch 2 = Up)

  • WARNINGS
CAUTION: The TV monitor in this game is a high voltage instrument. Extreme caution should be taken when any adjustment is performed while AC power is on. Such adjustments should be made only by qualified personnel.

Do not, under any circumstances, attempt to service the small logic board (CPU board), Any IC’s which are removed are automatically ruined and any tampering with the CPU board voids any and all warantees.

Page 5

tern f (68¢ 00/i28) ran 2a0v (0s604/)

MS 43% 0 “wees 31109 (7 Swerclt Pans) Connects To P4 (Pace 41) j 12] iil c i 54 E i $ K] 22 An EDGE ConnecroR.

> z r j a £ G g ‘a é xe vig isle] CaP | $3

a

qnalobs Barer) TIKES

Oed yale G Na ><! ly nawWeg | Zprwor

QO] ang 169 [ea] 1ohs Sev S} Ata AAS

Page 6

Swirett___fasel_ PLAYER | REAVER: 2 spore tye ' '

; ‘ Fine Fine | HARD SOFT ! GeneraL! Fine | Fine ‘agp | Soft |SHOT | SHOT | DDC isnot ‘shor » ConrRoL ' CONTROL. | corer CONTROL | CONTROL. ‘ ' 1

GE BG Grrvical)

  • LLL (came Select Sw ' CARe RetaTion | \-COUNT | 8-BALL Picea

PaMERTON Be ma

CONNECTS ym SK

ha face ).

Page 7

SUPPLY

Page 8

=

i] [atta

SE EDGE CONNECTOR

oy,

  • shel wr Taal Motorola Monitor. seienstic cin Model 501-10

Lye <a ett

Page 9

CABINET PARTS

7002 10128 10124 10100 10101 10102 10103 10104

METAL PARTS

10119 10112 10114 10113 10121 10120 10106

TRIM

10129

LOCKS

1486 1487

PARTS LISTING

Coin chute (2 x 25¢) Cash door, frame with cash box Cash box only for No. 308 door assembly Leg leveler - each Back service door Speaker screen TV screen mask - black plastic Header - plastic - screened Playing surface plastic - screened Playing surface plastic - grey Game rules - plastic - screened

California switch bracket Header retainer bracket - aluminum (each) Aluminum control panel Switch assembly mounting - Z bracket Playing surface support bar - front Front panel hold down bracket Monitor retainer bar

Black T-moulding for one side - 15 feet

Random lock with key and hardware No. 1150 lock with key and hardware

INSTRUCTIONS & LABELS

2920 2921 2919 2922 2909 Player 1 - TV screen label Player 2 - TV screen label 1 Player - 25¢, 2 Player - 50¢ - metal plate Time left - TV screen label Fuse below cover label

ELECTRICAL PARTS

10148 10116 9030 10105 10123 Complete smal! logic board (CPU board) Complete large logic board (game board) Complete Motorola 19" TV monitor Power supply - 110 volt Power supply - 220 volt

Page 10

ELECTRICAL PARTS (Continued)

10118 Fuse holder - dual 10130 Speaker - 16 ohm, 1.5 watts 10064 2 amp Slow-Blow fuse 1415 5 amp Slow-Blow fuse 2356 6 volt DC counter 10110 Fluorescent fixture, 18” 10111 Fluorescent bulb, 18’ - 110 volt 10146 6 volt bulb for control switches 10147 Header game light bulb - 220 voit 8028 Header game light bulb - 110 volt 8027 Header game light socket

SWITCHES

10131 California switch

AIM & SHOOT SWITCHES 10107 5 switch assembly - 3 aim, 2 shoot - complete with lights and engraved instruction lenses Individual aim and shoot switch components

10132 Switch mechanism 10133 Plastic body - black 10146 6 volt bulb Plastic lenses 10134 General control - orange counterclockwise 10135 Fine control - orange counterclockwise 10136 Fine control - orange clockwise 10137 Hard shot - green 10138 Soft shot - green GAME SELECTION SWITCHES 10108 4 switch assembly with lights and engraved instruction lenses Individual game selection switch components 10139 Switch mechanism 10133 Plastic body - black 10146 6 volt bulb Plastic lenses

10140 Rotation - red 10141 11-Count - yellow 10142 8-Ball - blue 10143 Carom Billiards - white 10109 START SWITCH 10144 Start switch mechanism only 10133 Start switch plastic body only 10145 Start switch plastic lens - start - red

roy