CATHODE RAY TOMES

Kick (General Instructions) (M051-009658-A010)

Kick (upright) (Midway, 1981) · Document · 20 pages · 4 sections · original scan

Page 1

©

. GENERAL INSTRUCTIONS

FOR

KICK

INSTALLATION

I. Unlock and open the coin box door.

II. Remove four (4) "CABINET LEVELING LEGS" from inside the coin box.

III. Tip the cabinet to the side and remove the shipping cleats from its bottom.

A. Locate the threaded holes - one in each corner - and install the "CABINET LEV- ELING LEGS" in them.

B. Level the cabinet.

C. When finished, the cabinet should be stable in the upright position.

IV. Plug the game into a standard A.C. wall outlet ONLY!

Game MUST be properly grounded.

A. The power ON/OFF switch is located:

  • UPRIGHT MODEL: On top of the cabinet toward the back.
  • MINI MODEL: In the center of the cabinet back just below the rear access door.’
  • COCKTAIL TABLE MODEL: Underneath the cabinet on Player No. 2's side.

LINE VOLTAGE SAFETY INTERLOCK SWITCHES

Line voltage SAFETY INTERLOCK SWITCHES have been provided for your protection. The locations of these SAFETY INTERLOCK SWITCHES are:

I. UPRIGHT MODEL: Inside the rear of the cabinet on the right side of the rear access door.

PART NO. M051-00968-A010

Page 2

IL. MINI MODEL: Inside the rear of the cabinet on the right side of the rear access door.

III. COCKTAIL TABEL MODEL: Inside the cabinet on the hinge side of the coin door.

When the cabinet access door(s) are secured in place, the SAFETY INTERLOCK SWITCH plunger(s) are in a fully depressed condition. The game circuit can function normally.

When any cabinet access door(s) are opened, the SAFETY INTERLOCK SWITCH plunger(s) are in a partially extended condition. This isolates the game circuit from the line voltage.

To restore power to the game circuit with the access door(s) open, gently pull the SAFETY INTERLOCK SWITCH plunger(s) out to the fully extended condition. THIS IS TO BE USED FOR SERVICING THE GAME ONLY!

SELF-TEST

A slide switch is provided to make the game run a "Self-Test" on itself. The SELF-TEST SWITCH is located on the mounting bracket for the left hand coin meter on the back side of the coin door.

To put the game into the Self-Test mode; turn the game ON and let it warm up for a few minutes. Then slide the SELF-TEST SWITCH to the ON position and actuate the "TILT" switch on the back side of the coin door just below the door lock to obtain the Self-Test-Menue display on the monitor screen.

When in the Self-Test mode, the monitor screen will display the results of certain test functions the game has run on itself. (These will be discussed in more detail later.)

TO SERVICE THE CONTROL PANEL(S)

I. UPRIGHT MODEL:

A. The control panel is held in place by two latches, one on the left side and one on the right side of the cabinet.

  • They are spring loaded to provide constant positive pressure on their latch plates.
  • They can be reached through the coin door AFTER turning power to the game off.
  • To release the latches, lift up and toward the center of the control panel.

a. Once they are released, unhook them from their latch plates.

B. To remove the control panel:

  • Raise it up and tilt it toward you until you can see the cable behind it.
Page 3

. 2.

3.

Cc. To Cradling the control panel between yourself and the cabinet, disconnect it from its cabling.

The control panel is now free and can be removed.

reinstall the control panel, reverse this procedure.

II. MINI MODEL:

A. The control panel is held in place by two latches, one on the left side and one on

1.

2. the right side of the cabinet.

They are spring loaded to provide constant positive pressure on their latch plates.

They can be reached through the coin door AFTER turning power to the game off.

To release the latches, Lift up and toward the center of the control panel.

a. Once they are released, unhook them from their latch plates.

remove the control panel:

Raise it up and tilt it toward you until you can see the cable behind it.

Cradling the control panel between yourself and the cabinet, disconnect it from its cabling.

The control panel is now free and can be removed.

reinstall the control panel, reverse this procedure.

III. COCKTAIL TABLE MODEL:

A. Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the control panel.

1.

2. Turn the power off to the game.

Open the coin box door and release the two latches on the inside of the cabinet up next to the table top.

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

a. Once they're released, unhook them from their latch plates.

Grasp the table top in the center above the coin door lifting up and to the side to tilt it open.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.
Page 4

-4&-

  • Remove the screws which secure the control panel in place.

B. To remove the control panel(s):

  • Disconnect it from its cabling.
  • The control panel is now free and can be removed.

C. To reinstall the control panel(s), reverse this procedure.

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY

I. UPRIGHT MODEL:

NOTE: In order to do this, the control panel MUST be removed first. See the "UP- RIGHT MODEL" procedure.

A. Turn the power to the game off and remove the control panel. Jhis frees the main-display-glass so it can be lifted up.

B. Grasp the main-display-glass in the bottom center, lift up slightly and pull it toward you about an inch, let it down just far enough so you can get hold of its top edge with your other hand and lift it out of the game.

C. Remove the rear access door.

D. Remove the screws which secure the T.V. bezel assembly in place (front and back).

E. The T.V. bezel assembly is now free and can be slid out of the cabinet.

F. To reinstall the T.V. bezel asssembly and the main-display-glass, reverse this procedure.

II. MINI MODEL:

NOTE: In order to do this, the control panel MUST be removed first. See the "MINI MODEL" procedure.

A. Turn the power to the game off and remove the control panel.

B. Remove the screws which secure the glass clamping plate.

C. Lift out the glass clamping plate. This frees the main-display-glass so in can be lifted up.

D. By putting your finger in the hole in the middle of the main-display-qlass support, you can lift it up and out.

E. Remove the screws which secure the T.V. bezel assembly and Lift it out.

Page 5

. -5-

NOTE: Use the hole in the center of the main-display-glass support to grasp it.

F. Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.

III. COCKTAIL TABLE MODEL:

NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST.

A. Remove the screws which secure the table top glass clamps in place.

B. Remove the table top glass.

C. Lift out the T.V. bezel assembly.

D. To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure.

VOLUME CONTROL POT

The volume control pot is located just inside the cabinet on the RIGHT side of the coin door frame. For adjustment, it may be reached through the coin door on ALL models.

To make the sounds louder, turn the pot clockwise (~~) as you face it.

To make the sounds less loud, turn the pot counterclockwise (4) as you face it.

VOLTAGE CONTROL POTS

The voltage control pots are located on the Linear Power Supply P. C. Board. They are preset at the factory and SHOULD NOT be tampered with at all unless the distributors service department is contacted first.

SELF-TEST

The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered.

You may begin a Self-Test at any time by sliding the Self-Test switch to the "ON" position after the power to the game is on (Self-Test switch located just inside cabinet on right side of coin door frame). When this is done, the game will react as follows:

1, If the game is in the Attract mode when the Self-Test switch is moved to the "ON"

Page 6

«6+

position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self-Test Mode Menue on the monitor screen.

If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the "ON" position, it WILL NOT go into the Self-Test mode until AFTER the players last Clown has fallen off his unicycle (the game MUST be over). At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self- Test Mode Menue on the monitor screen.

The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the "ON" position and then activate the "TILT" switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode.

The Self-Test mode has eight (8) major catagories as illustrated by the following Figure of the Self-Test Mode Menue as it should appear on the monitor screen.

1. It is easy to select what catagory you want to enter. By holding down the ONE or the TWO player button, the Balloon at the left of the screen can be moved UP and DOWN, (i=UP) and (ii=DOWN), until it is in front of the catagory you want to test. Release the button at this time.

After the Balloon has been positioned, depress either "KICK" button on the console and the monitor screen will display the test catagory you have selected.

NOTE: There is one exception to this. If you position the Balloon in fornt of the "PRE- SET" catagory on the Self-Test Mode Menue, when you press the "KICK" button on the console - - EVERYTHING, I repeat - EVERYTHING ; including ALL information in the "BOOKKEEPING" mode, and ALL operator selected options, will be set back to zero "0" and to the factory recommended settings - respectively.

° Once you are IN one of the Self-Test mode catagories, FOLLOW THE ON-SCREEN INSTRUCTIONS TO COMPLETE THE TEST.

The next group of Figures show the CORRECT screen presentation for EACH catagory of the Self-Test mode.

The first display of the Self-Test mode is the Self-Test-Mode-Menue. It should look like this: SELECT DESIRED TEST

1 SELF DIAGNOSTICS

2 SOUNDS

3 PLAYER INPUT

4 BOOKKEEPING

5 MACHINE SETUP

6 CHANNEL TEST

7 PRESET

8 GRID DISPLAY

Page 7

(MENUE - CONTINUED)

POSITION CURSOR BY USING 1 AND 2 PLAYER BUTTONS

HIT KICK BUTTON FOR TEST

During the SELF DIAGNOSTICS section of the Self-Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw "Second" are displayed again. And fifth, the different colored bars are replaced by this message: "HIT KICK BUTTON TO EXIT".

If the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad.

During the SOUNDS section of the Self-Test mode, the game will give a display which looks like the following:

SELECT A SOUND

1 ALL SOUNDS 2 EXIT 3 BALL BOUNCE 4 FALLING BALLOON 5 BALLOON EXPLOSION 6 WHISTLE 7 FALL DOWN 8 COIN 9 AMEN 10 BOMB FUSE 11 EXTRA CYCLE 12 BALLOON CAUGHT 13 MUSIC 1 14 MUSIC 2 15 MUSIC 3 16 MUSIC 4 7 MUSIC 5 18 MUSIC 6 19 MUSIC 7 20 POP TUNE 21 TILT 22 BALL GULP 23 PACMAN BONUS 24 PACMAN FALL 25 PEDAL CLICK 26 BALL POP

POSITION CURSOR BY USING 1 AND 2 PLAYER BUTTONS

Page 8

During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like the following:

As the Player Input Switches and Devices are activated, the Switch or Device activated is ( I spelled out in the blank space above "PLAY MUSIC". PLAY MUSIC This is a P.C.B. switch setting.

WHEEL VALUE

ACTIVATE ALL PLAYER INPUT SWITCHES AND DEVICES

HIT TILT TO EXIT

During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like the following:

SELECT A REPORT OR EXIT

CHUTE 1 COINS

CHUTE 2 COINS

LONGEST GAME

SHORTEST GAME

HIGHEST SCORE

TIME REPORT

SCORE REPORT

EXIT

POSITION SURSOR BY USING 1 AND 2 PLAYER BUTTONS

HIT KICK BUTTON FOR TEST

In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like the following:

TIME REPORT SCORE REPORT

0TO30 SEC0TO 3000 PTS
30TO60 SEC3000TO 7000 PTS
60TO90 SEC7000TO 10,000 PTS
Page 9

(TIME REPORT AND SCORE REPORT - CONTINUED)

90TO 120 SEC10,000TO 13,000 PTS
120TO 150 SEC13,000TO 17,000 PTS
150TO 180 SEC17,000TO 20,000 PTS
3TO4 MIN20,000TO 30,000 PTS
4TO5 MIN30,000TO 40,000 PTS
5106 MIN40,000TO 50,000 PTS
OVER6 MINOVER 50,000 PTS

HIT KICK BUTTON TO EXIT HIT KICK BUTTON TO EXIT

During the SETUP OPTIONS section of the Self-Test mode, the game will give a display which looks like the following:

SETUP OPTIONS

COIN CHUTE 1

  • = Factory recommended settings. *1 COINS FOR *1 CREDITS

COIN CHURE 2 *1 COINS FOR *1 CREDITS

*1 CREDITS FOR *3 BASES

1ST EXTRA BASE AT *10,000 PTS

ADDITIONAL BASES EVERY *10,000 PTS

*3 DIFFICULTY LEVEL

EXIT

USE KICK BUTTON TO POSITION CURSOR USE 1 AND 2 PLAYER BUTTONS TO ALTER OPTIONS

Page 10

The Difficulty Level setting has a range of 1 to 9. The following Figure shows what ef fect this option has on the game.

DIFFICULTY 1ST RACK IN WHICH YOU CAN ** NUMBER OF PAC-MEN THAT LEVEL HAVE 2 BALLOONS IN THE AIR CAN APPEAR IN RACK 2 SETTING AT THE SAME TIME AT EACH SETTING

worauelwn we nwwule ee nennwule ee

FACTORY RECOMMENDED SETTINGS

** THE NUMBER OF PAC-MEN IN EACH SUCCEEDING RACK IS REDUCED BY 1 UNTIL YOU ARE DOWN TO TWO PAC-MEN PER RACK. THESE WILL BE THERE FROM THAT POINT ON.

During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like the following:

CHANNEL TEST

CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 CHANNEL 6

HIT KICK BUTTON TO EXIT

Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until the Kick button is hit. It then goes back to the Self-Test Mode Menue.

During the GRID DISPLAY section of the Self-Test mode, the game shows a white cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until the Kick button is hit. The game will then go back to the Self-Test Mode Menue.

To leave the Self-Test mode, simply slide the Self-Test switch to the "OFF" position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will then return to the monitor screen.

Page 11

: -11-

KICK

OPTION SWITCH SETTINGS

TTTTTITTTTTTTITITISWItCH NO. 1 - AT B 3 - LOCATED ON SOUND 1/0 P.C. BOARD/TIT//ITITTITITIT

SwH1 SwH2 SWH3 SWiH4 SWHS SWHE *SWH7 SWHB SWHO SWH10 PLAY MUSIC ON NOT NOT NOT NOT NOT NOT = NOT DO NOT PLAY MUSIC OFF USED USED USED USED USED USED USED

MINI ON COCKTAIL TABLE OFF

FREEZE VIDEO ON NORMAL OPERATION OFF

SWITCH NO. 3 - AT D 14 - LOCATED ON SOUND I/0 P.C. BOARD

SWH1 **SWH2 **SWHB > *SWHE NORMAL OPERATION OFF SOUND I/0 DIAGNOSTIC MODE ON

NORMAL OPERATION OFF RAM/ROM TEST ON INDICATES TEST RESULTS VIA YELLOW LED ON SOUND I/O BOARD: FAST FLASH = BAD ROM

SLOW FLASH = BAD RAM

NORMAL OPERATION OFF OSCILLATOR TEST ON

NORMAL OPERATION OFF FILTER TEST aL

  • THIS SWITCH NOT USED ON UPRIGHT MODELS. ** NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF" POSITION.

THE REMAINDER OF KICK'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING THE MACHINE SETUP PORTION OF THE SELF-TEST MODE. SIMPLY FOLLOW THE ON-SCREEN INSTRUCTIONS TO MAKE ANY ADJUSTMENTS YOU FEEL ARE NECESSARY.

Page 12

EXTNAME: BF-GEN-INST (R)P: 12

MCR II SYSTEM

P. Cc. BOARD JUMPER OPTIONS

TITTTTTTTTTTTTTTTTTNIDEO GENERATOR P.c. BOARD/IIMTTTIZTT

MANUFACTUREREPROM NO.OW = =WH2 OWES = WHS =OWES =IWHG WHET) WHS.

MOTOROLA 68764 ‘

—— e766 *

INTEL 2764

T. I. 2564 %

TTT TH TITITTIT TTA TT TT TTT TT TIC. Pe Oe P. Cc. BOAR DIV TTT HT

MANUFACTUREREPROM NO.OWT = =SWH2 IWH3 SWE =SWHS = OWENOTE:

JUMPER OP-

NUMEROUR MFR'S2532*TION FOR

PROGRAM

NUMEROUS MFR'S2732*ROMs ONLY.

L 1 THT is OUND 170 P.c. BOAR OMNI

MANUFACTUREREPROM NO.OWT = OWH#2
NUMEROUS MFR'S2532*

NUMEROUS MFR'S 2732 *

  • = CUT JUMPER WIRES WHERE THIS SYMBOL '*" APPEARS.

The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the C.P.U. P.C. Board used in the MCR II System has 6 jumper wires, and the Sound I/0 P.C. Board used in the MCR II System has 2 jumper wires.

All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.

The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a "*" under that jumper wires number. If there is NO "*" under a jumper wires number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.

Page 13

KICK — ALL MODELS

SOUND1/0BOARDEPROMS

VERSION NO. 1

z Lore prs)

oafteu]
5re] ire)aco

e + GER

_ — 4 es fen ia \” " .

| [Ros] [Cro] & we sje] zt tors OF am |

alel (mesg |*' ee L2 +(crar ‘+ (cos) [R303] cay lee ene |oir| |aice| jars) +I ier moe

0968-00803 || 0968-008030968-008030968-00803
3800-A3900-B4000-C4100-0

\ KICK-- S-I/0 KICK-- S-I/6 |/KICK-- S-1/0 KICK-- S-1/0

\WHITEWHITEWHITEWHITE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C.BOARD to FUNCTION PROPERLY! !

Page 14

KICK -— ALL MODELS *

SOUND1/0BOARDEPROMS

VERSION NO. 2

t+ ces

[isa} ee ee GLH

Saal ;

B q ] esl : “le

fico

7 es] ez r q fr fave] [ei] | | Jez] low] | |e eis} [ewe | | siz] feta onl cor] |*| mio] fee z| [rey fees | ical fétoa cle] 24 foray

isosaa} dag
aZUW

ote *(ee +o] [e303] [306) frase) [raat 4001 +(e] Ese uno2 fori |}oie| lors) LEO wos EPIES ILC! coreg ‘eto! wa wloes

0968-00803 0968-00803 0968-00803 0968-00803 4200-A 4300-B 4400-C 4500-0 KICK-- S-1/0 |KICK-- S-1/0 ||KICK-- S-I/0 ||KICK-- S-I/0 GRAY GRAY GRAY GRAY

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C.BOARD to FUNCTION PROPERLY! !

Page 15

0968-00803 0600-4 KICK---UR-CPU BLUE

0968-00803 0700-8 KICK---UR-CPU BLUE KICK UPRIGHT

cPU EPROMS

VERSION NO. 1

war ro 1 [2] Gat a

KICK-~-UR-CPU

0968- oss

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that 0968-00803 0800-C gee 2 ggegegh & 8 a ; AAG A000 0_ iz} ts) sg] |o ae 3

Ss =o)

(Gz)

7° ev | Grp) cen P30 cre

1esoeCe]=

oe AD (crs) cr

assco[es
EERECzio)
| x0]10 *}5|10
oo SD) GH we) 02rsGi)
2] me]mo]fre
Gree) (rss)(zy)(rss) .- Gei2)
ea ro Cas oRore CESSS| (Ha
) GD GDCEEC)

as os +

  • RS] es] Ged bis LS*tsou) | 3
sCS)G2) EG jheGow) |*

Fas 215 |5

157 CD 38 Gala

will enable this P.C.BOARD to FUNCTION PROPERLY! ! KICK---UR-CPU BLUE

KICK---UR-CPU BLUE

Page 16

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

KICK MINI AND COCKTAIL

VID. GEN. EPROMS

VERSION NO. 1

20rm 4m 209m arm 207m a

[ enratTs

carocenp = er

ur [Ene tees) [et te a fe e a2 2 ©

= ast Ged ep Te" ED ED ED

  • Tana

oom coal = os | [e os «= ] feq

Dp ws |: Te— Es es a2 | or | oe |

Fe ZH De rs 7a] =e : ==

2= o0513-00803
=. one 16g :2100-D

ee” co oa es re ' KICK--M&C-VG sez Grad > wat) Pal fez ai YELLOW

=70513-00803

Te on Ds a ae oe a > 2000-¢ 1 KICK--M&C-VG ep BZ EQ, E> & em |e et = ots oes a. = ss | & 0513-00803

eptes) €» ED an .1900-8
= iad‘KICK--M&C-VG

Ee] ar oe = = oa = YELLOW = E> eS = & a Tes 7 0513-00803

; - : 7 :a1800-A

aT ae fe] vi as rei rch eda eeve ee ED eD cD eH Carp) tony YELLOW

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C.BOARD to FUNCTION PROPERLY! !