CATHODE RAY TOMES

Centipede Caberat TM-189 1st Printing

Centipede (revision 4) (Atari, 1980) · Technical Manual · 56 pages · 40 sections · original scan

Page 1

\ Operation, Maintenance

and Service Manual

<\ sD, ‘i

Page 2

GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a silver identification label. If your game is UL-listed, this label is located on the front of the game, underneath the speaker. Otherwise, the label is affixed to the rear panel of the game. The same serial number is also stamped on the chassis of the monitor, Regulator/Audio Il PCB, power supply, and Centipede™ Game PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL NUMBER IDENTIFICATION TAG

En

MONITOR Ny

REGULATORIAUDIO II PCB

g CENTIPEDE GAME PCB

POWER SUPPLY

Page 3

Ty

Operation, Maintenance

<A and Service Manual Complete with lilustrated Parts Lists

Page 4

Centipede ™/Cabaret™

Copyright © 1981 by Atari, Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval sysiem, transmitted, or otherwise copied for public or private use, without permission from the publisher.

Published by: ATARI, INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A. 6K

Page 5

Centipede ™/Cabaret™

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

Set-Up Procedures A. NewFeatures......... 0... ccc eee eee cette ene eeee B. Game Inspection . Cc. Game installation...

  • Voltage Plug Selection
  • Interlock and Power On/Off Switches . D. Self-Test Procedure ............... E. Option Switch Settings .
  • Bonus Play Feature. .
  • Coin Mechanism Multipliers .
  • Examples of Game Price Settings . F. GamePlay ...........-....2.
  • Attract Mode ....
  • Ready-to-Play Mode .
  • PlayMode ......... :
  • High Score Initial Mode ... 1.6.0.0... ccc cece eee neenee

Maintenance and Repair A. Cleaning...... B. Fuse Replacemen C. TheControl Panel ..........

  • LED Start-Switch Replacement .
  • Leaf-Switch Replacement........
  • Mini-Trak Ball™ Maintenance and Repair . D. Monitor Removal ...........0....05 E. Printed-Circuit Board Removal
  • Game PCB Removal ........
  • Regulator/Audio I! PCB Removal F. Game Operation. ...... 0000. c eee cece eens

Illustrated Parts Lists Illustrations and parts lists begin on page ......... 0.0.0.0 cece eee OOWDDR AWWA

Page 7

List of Illustrations

Figure 1 Overview of Game ..... 20.0.2. 2 Figure 2 Installation Requirements .. 3 Figure 3 International Voltage Plug Selection . 4 Figure 4 Interlock and Power On/Off Switches 5

Figure 5 Self-Test Procedure. ......... 2.0. e cece cece eee eee 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches ... 8 Figure 7 Game Option Settings .. Figure 8 Game Price Settings ........ 0.0... eect cence eee eee

Figure 9 Coin Counter Option Settings .... 2.6.6... c eee eee eee 12 Figure 10 Opening the Control Panel and Replacing Switches . 18 Figure 11. Control Panel Wiring ..................0005 19 Figure 12 Mini-Trak Ball™ Maintenance and Repair.............. 0.00. 0eee ee 20

Figure 13 Monitor Removal ........... 00.00 c cece cece een eet Figure 14 Printed-Circuit Board Removal Figure 15 Power Distribution ....................0085 “ Figure 16 Signal Distribution .......... 0... eee eee eee eens

Illustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies ..........-. 0.0 e cece renee eee 28 Figure 18 Control Panel Assembly Figure 19 = Mini-Trak Ball™ Assembly .... Figure 20 Regulator/Audio I! PCB Assembly ......... 0.0.00. e cece eee ences 34

Figure 21 Centipede™ Game PCB Assembly . Figure 22 PowerSupply Assembly...... Figure 23 Vertical-Mounted Coin Door........... 60sec cence cece eee ene 42

Page 8
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) exe From California, Alaska or Hawaii > (408) 745-2900

ae From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A. Game sales and service only

Atari, Inc New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)

@ 06252155

vi

Page 9

Set-Up Procedures

A. New Features

The Centipede™/Cabaret™ game has several new features. Even if your are familiar with Atari games, you should note these important differences. The new features are: @ = Mini-Trak Ball™ Assembly. The widely used Trak Ball assembly has been redesigned. The basis for this compact, simplified design is a two-part molded plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. @ The circuitry has non-volatile memory that automatically counts the number of games played and averages the game time. Also, the three highest scores in the high score table will permanently stay in memory. To erase this information, follow the instructions in Figure 6, Self- Test Procedure. @ This game introduces Atari's new verticalmounted coin door assembly. It allows full access for servicing the coin acceptors and other electrical parts, yet provides security for the cash. Therefore, the two doors in this assembly are separately keyed. @ The addition of a foam pad on the rear access panel insures that the safety interlock switch will be completely closed when you lock this panel. @ Additional Improvements: The wiring harness has been redesigned so that signal and power wiring are now separated to provide ease of maintenance and troubleshooting. Second, all monitors used are UL-Recognized and CSA-Certified, thus providing the most reliable and highest quality monitors available in the marketplace today. In addition, the power supply chassis has been fitted with a metal bottom plate, making it a totally self-contained unit. Fourth, the attraction panel and monitor shield are now made of tempered glass to facilitate cleaning and improve visibility. These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol:

Page 10

a

MONITOR SHIELD

COLOR MONITOR

a MINL-TRAK BALL™ CONTROL

START SWITCHES. *

REGULATOR! AUDIO II PCB

CONTROL PANEL

COIN DOOR

INTERLOCK SWITCH

POWER ON/OFF POWER SUPPLY

SWITCH

Figure 1 Overview of Game

Page 11
WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or-with metal objects held in your hands! outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if . , . this game is not properly grounded! @ Note the location of the game's serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Centipede™ game PCB, Regulator/Audio I! PCB, power supply, and monitor are all identical. A

B. Game drawing of the serial-numbered components

is on the inside front cover of this manual. s

Inspection Please mention this number whenever you

call your distributor for service. . . @ Check ail major subassemblies such as the This new game is ready to play upon removal from power supply, control panel and monitor for the shipping carton. However, your careful inspec- secure mounting. tion is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good

condition. Cc. Game

NOTE Installation

| Do not plug the game in yet!

Figure 2 Installation Requirements 1, Examine the exterior of the game cabinet for Power 130 watts dents, chips, or broken parts. Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative

  • Remove the screws that were used as extrase- | Space Required 52x 78% cm (20% x 31 in.) curity to seal the rear access panel. Unlock and Game Height 153% cm (60% in.) open this panel, as well as the coin door; inspect the interior of the game as follows:

@ Check that al! plug-in connectors (on the game harness) are firmly seated. Repiug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty.

@ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.

®@ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black metal strainrelief plate in the wood slot at the bottom of the rear panel opening.

Page 12
  • Voltage Selection If you live outside the United States, your Centipede™ game has the international or European power supply with two or three colored plugs. Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure
  • is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed (see Figure 4). One is located behind the rear access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a dooris opened. Check for proper operation of the interlock switches by periorming the following steps: @ Be sure the access panel and the coin door are closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the on position. Within approximately 30 seconds the monitor should display a picture. @ Slowly open the rear access panel. The monitor picture should disappear when the panel is opened approximately 2% cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ if the results of the preceding step are satisfactory, the interlock switches are operating properly. If the monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (225) Blue 220-260 VAC (240) Brown

NOTE: Your game will be supplied with only one, two or three of ‘the above plugs. If you need to replace any of them, refer to Figure 22 for part numbers of all four plugs.

Figure 3

WARNING

Fuse cover must be in place during game operation.

International Voltage Plug Selection

Page 13

On SAFETY INTERLOCK SWITCH

ON > POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

Centipede ™/Cabaret™

D. Self-Test Procedure

The Centipede/Cabaret game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor, the light-emitting diodes in the start switches, and the game speaker; no additional equipment is necessary. Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.

To run the self-test, follow the instructions outlined in Figure 5.

Figure 5 Self-Test Procedure

Instruction Results if Test Passes (if results are not as indicated, see list of failures that follows)

  • Begin: Set self-test switch to on position (see Figure 6).
  • Trak Ball Test: Roll the Trak Ball control in ali directions.
  • Switch Test: One after another, activate and release all 3 control-panel switches, the slam switch, and coin door switches.*

4, Audio /0 Chip Test: One after another, press and hold 2 of the control-panel switches and at least one of the coin-door switches.

  • Audio 0 Channel Test: Press ‘-player start button four times.
  • Background Color Test: Press 1-player start button at least eight more times.
  • Object Color Test: Press 2-player start button at least 16 times.
  • Moving Object Test: Watch the screen, and move the Trak Ball around. Place the moving object in an open area of the screen. Press fire button several times.
  • Erasing the High Score Table (optional) The current three highest scores are held in permanent memory, The monitor displays the picture below. The game produces no sound at all. The two LEDs will stay on throughout self-test.

The centipede head moves around on the screen in directions corresponding to Trak Ball control.

‘As long as you activate (close) each switch, you'll hear a high beep.

Volume increases and pitch decreases with each additional switch that is activated.

You'll hear a high beep for each press of the button.

Background color changes with each press of the 1-player start button.

Objects on playfield change color.

Each press of the fire button changes the moving object to another moving object. At certain points in the series, the object will disappear. This is not a failure indication.

even if the game is

start butions. The 4 FF message in the upper left corner of the screen will then be disunplugged. If you want to erase these scores, simultaneously press the fire and two § played. The average game time data will also be erased, but still displayed on the screen,

  • End: When satisfied with test, set self-test switch to off position.
  • Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you stay in self-test.
Page 15

Figure 5 Self-Test Procedure, continued

Results if Test Fails

  • Begin: RAM FAILURE is indicated by one to 10 beeps. Note the number of beeps and determine which RAM may be bad. To restart the tesi, press the reset pushbutton on the game PCB, or set the selftest switch to off, then again to the on position. Possible Bad Number of Beeps Given RAM Chip Location 1 H2 2 F2 3 K7 4 KS 5 L7 6 Ls 7 M7 8 MS 9 N7 10 N5

Any bad RAM must be replaced before the computer can check the other RAMs, as well as continue with the self-test.

ROMIPROM FAILURE is indicated by two groups of numbers in the upper left corner of the screen. The number at the far left indicates the location of the failing PROM/ROM(s). Identify the bad ROMIPROM with the table below. If the screen displays “garbage,” or the logic produces strange audio or randomly activates the coin counters, the chip at location J1 is probably bad. Ignore the hexadecimal numbers just to the right of the chiplocation number. Failing ROMIPROM Displayed Number Chip Location 0 Dt 1 1 2 FIH1 3 or “garbage” J 4* ES* 5 BICIDS “If you replace or erase this ROM, the number 4 FF will be displayed throughout the self-test. The next time you enter self-test, the 4 disappears after a game is played. Otherwise the self-test will continue to display the numbers 4 FF.

  • Trak Ball Test: The character doesn't move in same direction as ball, jumps rather than moves smoothly, or doesn’t move at all. One of the Coupler PCBs or Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.
  • Switch Test: Sound is constantly on, even though you are not activating any switch. Or, no beep is given for any switch, or LED is dark. Indicates a bad switch, loose harness wires, bad LED-driving circuitry, volume turned all the way down, or loose connector.

4, Audio VO Chip Test: No increase in volume or decrease in pitch indicates bad custom audio VO chip at location B/C/D3.

  • Audio /O Channel Test: On one out of the four activations, no audio is produced. Indicates one channel is bad in the custom I/O audio chip at location B/C/D3 (replace entire chip).
  • Background Color Test: Background doesn’t change color, or doesn't display all 16 colors. Indicates bad color RAM chip. (RAM failure would have been indicated earlier with from 3 through 10 beeps.)
  • Object Color Test: Objects don't change color, or don't display all 16 colors. RAM failure.
  • Moving Object Test: Object doesn’t change to another object. ROM/RAM failure.

NO. OF LIVES AT START OF GAME

ALL SWITCHES & goraet TRAK-BALL INPUTS STOOL OOLOY ny ROL TOLOOL LOLOO. BONUS COIN SETTING (means “for every 3 coins inserted, logic adds 1 more coin”). Blank if no bonus coins(s) given. See Fig. 8 for switch settings. 92 PLays: 1:59 GAME TIME

GAME DIFFICULTY SETTING ENTIRE CHARACTER SET

L, R COIN MECH MULTIPLIERS

TOTAL NO. OF CREDITS PLAYED

AVG. GAME TIME (accurate to +4 secs)

Page 16

Centipede ™/Cabaret™

E. Option Switch Settings

  • Bonus Play Feature The Centipede™ game offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

SWITCH ‘VOLUME CONTROL VOLUME INCREASE: TURN CLOCKWISE

ELF-TEST For example, with your game set at 25¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus coin. Therefore, players receive 5 plays for $1.00.

CENTIPEDE™ GAME PCB

Figure 6 Location of Self-Test Switch,

Volume Control and Option Switches

Page 17

This bonus feature encourages players to insert more money than just the minimum 25¢ you could require for one game. Various other bonuses are available (see Figure 8).

  • Coin Mechanism Multipliers This game has a new vertical-mounted coin door combined with coin-box entrance; it has two mechanisms. All recent Atari game PCBs identify the two mechanisms in a certain pattern.

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic.

The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/$1 coin door, you will probably want to set the left and right option-switch multipliers at x 1/ x 4.

You can set these multipliers with toggles 3 thru 5 on the Centipede™ Game PCB switch assembly at location N8. For exact settings of these toggles, refer to Figure 8.

  • Examples of Game

Price Settings

Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location N8; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7, 8, and 9 provide “$” signs indicating Atari’s recommendations.

Figure 7 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Centipede Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.

Toggle Settings of 8-Toggle Switch on Centipede Game PCB (CENTER switch assembly when PCB is in game) 8 7 6 5 4 3 2 {at N9)

1 Option

On On. Off Off On On On Off

Off On

Off Off

On On On Off

On Off On Off On English $

Off German

On French oft Spanish 2 lives per game 3 lives per game $ 4 lives per game 5 lives per game Bonus life granted at every: 10,000 points 12,000 poinis $ 15,000 points 20,000 points “»S Hard game difficulty* Easy game difficulty* $ t-credit minimum $ 2-credit minimum

$ Manufacturer's suggested settings “Refer to Section F. Game Play, for information on game difficulty. For pricing for “credits,” see Figure 8 Changing toggles 3-7 erases the high score table.

Page 18

Figure 8 Game Price Settings The white biock below contains Atari’s Suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation (labels are on the following page). Use the cation N8, on the Centipede™ Game PCB (the LEFT switch as- label no. 6 (indicated with ©) only if you set toggle 8 at PCB sembly) switch assembly NQ to off.

50¢ PER CREDIT

Bonus Bonus $.75 = 2 credits No bonus $1.00 = 3 credits $1.00 = 3 credits

Off a

‘Straight 25¢ Door

250/$1.00 Door

25¢ PER CREDIT

Bonus No bonus $.50 = 3 credits

8765
Straight@ofofofoff

25¢ Door

4321
OffOffOnOff

25¢/$1.00

Page 19

Centipede™Cabaret™

Figure8Game Price Settings, continued

The switch settings below relate to options for game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Centipede™ game on free play, or if you have German coin mechanisms in your door. To achieve bonus plays, all coins must be inserted before pressing the start button. The label no. 6 shown below should be used only if you set toggle 8 at PCB switch assembly N39 to off.

Toggle Settings of 8-Toggle Switch on Centipede PCB (at N8). LEFT switch when PCB is in game

876§4321Option
OnOnFree play
OnOff1 coin® for 2 credits
OffOn1 coin* for 1 credit$
OffOff2 coins* for 1 credit
OnOnRight coinmech x 1$
OnOffRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6
OnLeft coinmech x 1$

Off Left coin mech x 2

OnOnOnNo bonus coins$
OnOnOff

On Off On On Off Off Off On On Off On Off

For every 2 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins” inserted, game logic adds 2 more coins* For every 5 Coins* inserted, game logic adds 1 more coin*™ For every 3 coins” inserted, gare logic adds 1 more coin*

*in the U.S. a “coin” is defined as 25%. In Germany a “coin” is 1 DM.

$ Manufacturer's suggested settings To achieve bonus piays, all coins must be inserted before pressing start button.

Game Pricing Labels

e 2 @@ 2 coins =1 play

e :

JL@i coin=1 play

AO @@ 2 coins =1 play ATARI 6 ee @ 4 coins = 3 plays ne @@ 2 coins *8) Q@®@ 3 coins 00@@ 4 coins

© ee 2 coins = 1 play A @ $1 coin =3 plays (Susan B. Anthony coin)

oO. @ icoin = 1 play

ari 2 play minimum (2 coins = 2 plays)

(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)

n

Page 20

Centipede™Cabaret™

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle Switch on Game PCB (N11) 4 3 2 41 Two coin acceptors in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game: Three coin acceptors in the coin door:

OnOnBoth acceptors activate all coin

counters simultaneously.

OnOffBoth acceptors activate 2 count-

5 ers separately. BB 8 8 3.3

&$$OnOffBoth acceptors activate all coin

counters simultaneously.

OffOffBoth acceptors activate 2 count-

ers separately. $ Do not use this setting.

Do not use this setting.

Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate all coin counters simultaneously.

Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters separately. All 3 are same denomination and they activate all coin counters simultaneously.

Left and center acceptor activate ‘one coin counter; right acceptor activates another coin counter.

Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.

Left, center and right acceptors activate 3 coin counters separately. $

$ Manufacturer's suggested setting

F. Game Play

Atari’s Centipede™ game is a one- or two-player game with a color raster-scan monitor. The fast-moving action includes a variety of creatures dropping down from the top of the screen or flying in from its sides, most of them to attack the player. The player’s shooter is represented on the screen by asomewhat humanoid head.

The player's goal is to shoot at and destroy as many of these creatures and mushrooms as possible for a high point score, before the player's lives are used up. Players can maneuver their Trak Ball™ control anywhere within approximately the bottom fifth of the screen. However, they must move around mushrooms, since these are fixed, not “transparent”, objects. A fire button shoots individual shots upwards, or fires a hail of shots if pressed constantly. (Only one shot appears on the screen at a time.)

The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. Wait at least eight seconds after a game has been played before entering selftest or turning off the power. Otherwise, you may erase the high score table, the average game time and the number of plays.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the monitor displays two pictures simultaneously.

One of the pictures is operator-selectable for one of four languages. Placed in the center of the screen, the picture shows the high score table, game price, and the bonus-life achievement level. If the operator sets the Centipede game for free play, the game will not display a game price message.

The high score table shows the eight highest scores and their matching initials. If you erase the special “permanent” memory (see Figure 6, Self- Test Procedure), then this table will contain fictitious scores and initials. The table is redeveloped from subsequent games with scores of more than 12,102 points. Subsection 4, High Score Initial Mode, explains this table in more detail.

Page 21

Operators may choose one- or two-credit minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings).

If the game is set for a 2-credit minimum, that message will be displayed on the screen. (No special message appears if Centipede is set to the opposite setting, namely 1-credit minimum.)

The other picture surrounds the high score table, game price and bonus-life achievement level messages. That picture displays a typical game-play sequence, with a field of colorful mushrooms through which a centipede crawls. The spiders bounce in from the sides of the screen, and fleas occasionally drop down from the top. In addition, scorpions will cross the screen at almost any point.

In this mode, the action exactly duplicates a typical game played by a moderately skilled player: the player's shooter moves freely within the limits of motion, shooting at spiders, centipedes, fleas and scorpions. Periodically the player is “destroyed” when a flea, spider or centipede head or body collides with the player’s shooter.

All the colors on the screen change with each wave. A new wave occurs when the player shoots all centipede parts remaining on the screen. At this point, a new centipede starts snaking its way down from the top of the screen.

The attract mode differs from real game play in that no head figures are shown at the top of the screen to represent the number of lives remaining, no sounds are produced, no scores are incremented, and none of the four player controls work.

At any time when the game is powered up, if the slam switch is closed, you will hear a special alarm sound. This sound alerts location personnel that the game has been abused.

  • Ready-to-Play Mode This mode begins when sufficient coins are accepted for a one- or two-player game. It ends when the 1-player start or 2-player start pushbutton is pressed. When this mode begins, the message CRE- DITS __is displayed in the middle of the screen. The pictures are otherwise the same as those shown in the attract mode.

If you select the two-credit minimum and a player inserts enough money for only one credit, the message 2 CREDITS MINIMUM flashes on the screen until enough coins for the second credit are inserted.

In addition, CREDITS 0’ is displayed if you have selected the option of two coins per credit, and the player has inserted only one coin. A “credit” is defined as the cost for each player to play one game. In other words, two credits will pay for: @ one player playing two games, or @ two players playing one game.

  • Play Mode The play mode begins when any flashing start pushbutton is pressed. The mode ends when the piayer’s last life is lost.

A player's shooter is enabled at the beginning of the play mode, and the audio starts. The appropriate LED start switch will then stay lighted until the end of the game. At this point it will flash if any credit remains.

The game begins with a playfield of randomly placed mushrooms. A centipede start snaking its way across from the center top of the screen, The centipede changes direction when it runs into a mushroom or either the left or right boundaries of the playfield.

Page 22

When a centipede is shot, it breaks into two smaller ones, each with a head. Also the part of the centipede that was shot leaves a mushroom in its place on the screen. When any centipedes reach the bottom of the screen, they start back up, but remain within the area of the player's shooter (the bottom fifth of ihe screen).

When a large centipede (that hasn’t been shot yet) reaches the bottom, it releases its tail, and this part changes into a new head. Also to provide player challenge, if a centipede is still alive when it reaches the bottom, new heads will enter the screen almost at the bottom of the sides. More of these heads will appear as time progresses.

The randomly moving spiders also appear in the first wave. The spiders can destroy a player, as well as any mushrooms they move over. This eliminates many mushroom targets for a player.

The player's shooter is moved by rotating the Mini- Trak Bail™ control. The shooter can be moved in all directions, but only within the bottom fifth of the screen. Pressing the fire button causes the shooter to fire shots upwards, either singly or in rapid-fire mode, if held down constantly. Mushrooms count 1 point when shot, and a player must fire four shots into a mushroom before it is destroyed and disappears. Centipede body parts count 10 points each, and the elusive heads (represented with small eyes on them) are worth 100 points each. Spiders are worth 300, 600 or 900 points, depending on how close they are to the player when shot.

A bombardment of fleas starts in the second wave; as the fleas descend, they leave a trail of new mushrooms behind them.

In the second wave, the fleas appear when a certain number of mushrooms remains at the bottom of the screen. This number increases as the game progresses, meaning fleas appear more often later on in the game.

Fleas have a value of 200 points when shot, and players must hit them twice to destroy them (the first shot just speeds them up).

The scorpion enters from either side starting in the fourth wave; it moves at a relatively siow speed. Later it increases its speed. When shot, a scorpion counts 1000 points—the highest-value target of all.

Page 23

As it travels across the screen, it “poisons” the mushrooms that it moves over and changes their colors. These mushrooms cause any centipedes that would collide with them to head straight towards the bottom of the screen, rather than continue snaking around. Players can stop a poisoned centipede by shooting its head.

In addition, these poisoned mushrooms as well as any partially shot mushrooms add 5 points to the player’s score at the end of each life when the screen is resetting.

lf the players are very skilled and earn at least 60,000 points, two things happen to increase player challenge: the fleas descend at a faster speed and the spiders restrict their movement to a smaller area at the bottom of the screen.

An important new jeature of this game is the operator option for easy/hard game difficulty. In the easy game, the spider moves slowly up to a 5,000-point score, and then bounces at a higher speed. It also changes direction less often throughout the game than at the hard setting.

In the hard setting, the spider moves slowly only for the first 1,000 points, and then speeds up. It also changes direction more often throughout the game. In either setting, the spider always moves at a 45-degree angle or straight up and down.

Another operator option is the number of lives per game, ranging from 2 to 5 (see Figure 7 for switch settings). This number is displayed as small shooters at the top of the screen. The number is de- Centipede"™/Cabaret™

creased by one each time a player is destroyed. The number is increased by one each time the player scores multiples of 10, 12, 15 or 20 thousand points, depending on the operator selection.

  • High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. At the beginning of this mode, the characters A____ appear on the screen. The logic will also display the messages GREAT SCORE and ENTER YOUR INITIALS.

Players enter initials one character at a time, choosing from the characters A thru Z and a blank space. Pressing the first button selects the letter, and rolling the Trak Ball control changes the letters on the screen.

After the fire button is pressed the third time, the initials and score are transferred to the table. This table contains eight scores and appears during the attract and ready-to-play mode.

All but the highest three scores are erased whenever you enter the self-test, or press the RESET button on the game PCB, or turn off the power. The resetting replaces the lowest five scores with fictitious scores and initials.

If you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and initials. In other words, the table will always be displayed on the screen, possibly consisting of one or more realistic scores and players’ initials.

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

Maintenance and Kepair

t All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if Mini-Trak Ball™ control, leaf switch or light-emittingdiode (LED) switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the Mini-Trak Bali contro): for details see this chapter.

Page 26

To remove LED switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. ® Install a new switch using the reverse procedure. @ Reconnect the harness wires. COMMON CONTACT LIGHT-EMITTING-DIODE (L.E.D.) CONTACTS

NORMALLY OPEN “~~ (N.O.) CONTACT

NORMALLY CLOSED (N.C.) CONTACT

Figure 10 Opening the Control Panel and Replacing Switches

A. Cleaning

The exterior of the game cabinet and the metal and glass surfaces may be cleaned with any nonabrasive household cleaner. \f desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

Do not dry-wipe the attraction panels, because any dust can scratch the surface and result in fogging the plastic. The large monitor shieid is made of tempered glass and should be scratch-resistant: if cleaned without abrasive substances, you should hardly ever have to replace it.

B. Fuse Keplacement

This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 22 of this manual. See the color monitor manual for the monitor fuse data. Cc. The Control

Panel

Prior to repairing or replacing any switch or the Mini-Trak Ball™ on the control panel, unplug the game. Then open the coin door.

Reach through the coin-door opening and open the luggage-style latch, located at each end on the underside of the control panel (see Figure 10). Lift up on the control panel at the topmost edge and tilt it towards you.

The edge of the contro! panel next to the monitor shield has foam tape applied to it. This tape acts as a cushion for the glass and prevents spilled liquids from entering the cabinet interior. Always make sure this tape is in good condition.

When reinstalling the switches or Mini-Trak Ball control, reconnect the harness wires as shown in Figure 11. Make sure the right colors go to the tabs on the switches and the right connectors go to the PCBs on the Mini-Trak Ball.

Page 27

AURIZ-MOTION PCB: BLUE, RED, BLACK & VIOLET WIRES

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10. @ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
  • Leaf-Switch Replacement
NOTE Adjust switch for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

The leaf switch on this game operates on 5 volts at a very low current. Therefore, pitting of the switch would be extremely rare. Probably the only reason Centipede ™iCabaret™

that pitting would occur is that the game is in a very high-humidity location.

Don’t burnish the switch contacts. Burnishing them removes their piating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacis is to wipe them with a non-abrasive surface. A business card works very well.

To replace the switch, remove both of its screws with a Phillips-head screwdriver—see Figure 10.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the contro! panel. The white ring on the outside of the control panel should not spin, due to its design.

3. Mini-Trak Ball™ ew

Maintenance and Repair The Mini-Trak Ball™ control requires lubrication of its bearings approximately every 3 months or every 6,000 credits. To lubricate or repair the control, remove it from the contro! panel and disassemble as illustrated in Figure 12.

Use only 2 drops of 3-in-One® oil in each of the six bearings of the Mini-Trak Ball™ control.

For further instructions on how to replace the ball, either coupler PCB or either encoding wheel, see Figure 12.

VERT.-MOTION PCB: GREEN, RED, BLACK & YELLOW WIRES.

CAUTION Players may receive an electric shock if this contro! panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

Figure 11 BLACK

GREEN

WHITE

WHTIBLK. STRIPE

RED

Control Panel Wiring

Page 28

Disassemble in the order indicated. (Circled numbers match the steps described below.)

Ball Replacement

  • First remove the entire Mini-Trak Ball™ assembly from the control panel as shown in Figure 11. Now locate the six “twin-lead” thread-forming screws in the black frames or Plastic pieces; remove these six screws.
  • Liftoff the top frame; remove and replace the ball.

Coupler PCB and Encoding Whee! Replacement

  • Lift the PCB out of its slot. Caretully unplug the red connectoron the coupler PCB.
  • To replace either encoding wheel, remove the PCB from its slot. Remove the socket-head machine screw, flat washer, and split lock washer that secure the encoding wheel. Remove the wheel.
  • When replacing the coupler PCB, be certain that the black metal encoding wheel has not been bent or damaged. !t should turn freely between the two halves of the ted photosensor device.

LUBRICATE HERE (6 PLACES)

Figure 12 Mini-Trak Ball™ Maintenance and Repair a

Page 29

D. Monitor Removal

The following procedure should only be performed by a qualified service technician.

WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor.

To remove the color monitor, follow steps 1 thru 7. Refer to the accompanying Figure 13. Centipede ™/Cabaret™

Be sure the game is unplugged from its wall outlet! Unlock and open the rear access panel, coin door, and control panel. Remove the glass monitor shield. Carefully remove the two staples that secure the blue cardboard bezel. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. Standing at the rear opening of the game, locate the 2-pin and 6-pin harness connectors for the monitor. Unplug both of these. At the bottom rear of the monitor chassis are a self-locking hex nut, fiat washer, and carriage bolt that secure the rear part of the chassis toa large metal bracket. Remove this hardware. From the front of the cabinet, locate the flat washers and self-locking hex nuts (two Sets underneath, and two sets above the monitor screen). This hardware attaches the monitor to the cabinet. Remove this hardware. Carefully pull the monitor chassis out of the cabinet towards you. When reinstalling the monitor, be certain that you securely attach the ground wire to the bottom right machine screw.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 13 Monitor Removal

ai

Page 30

E.

Printed-Circuit Board Kemoval

You may wish to remove the Centipede™ game printed circuit board (PCB) or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 14 and proceed as follows:

1. ° Game PCB Removal Unlock and open the rear access panel. Remove the 24- and 44-pin edge connectors from the right side of the game PCB. Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove and save this screw, as well as the fiber spacers. Remove the PCB from the cabinet by carefully sliding it straight out of the plastic PCB retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as necessary. After servicing, reinstall the PCB, making sure that the two edge connectors are properly plugged in. Note that the connectors are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your PCB and will void the warranty. Check that the operation of the game is correct by performing the self-test. It is especially important to do the self-test with any game when you replace a PCB.

Regulator/Audio Il PCB Removal Unlock and open the rear access panel. Remove the five plug-in connectors on the Regulator/Audio || PCB. Note that all of these connectors are keyed for proper orientation. Locate the Phillips-head screw that extends through the PCB and into the wood behind the PCB. Remove and save this screw and the two fiber spacers. Remove the PCB from the interior wall of the cabinet by carefully sliding it straight out of the plastic PCB retainer. Again, be careful not to twist the board. Replace or repair as necessary.

REGULATOR! AUDIO Il PCB

CENTIPEDE™ GAME PCB

Figure 14 Printed-Circuit Board Removal

Page 31

F. Game Operation With this manual you received two large sheets that contain the wiring and schematic diagrams for the Centipede™/Cabaret™ game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They explain the functions of the circuits; the diagrams also define inputs and outputs.

Atari’s Centipede™ game is microprocessor-controlled. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio Il PCB, loudspeaker, and control panel. The Regulator/Audio || PCB performs two funciions: 1) it regulates the + 10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speaker and is controlled by the volume control, mounted on the bracket inside the coin door.

The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The Primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power-supply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals.

Page 32

CONTROL PANEL

MONITOR

+5 VDC REG.

REGULATOR/ AUDIO II PCB

INTERLOCK

INTERLOCK: ‘SWITCH

SWITCH

GAME PCB POWER ON/OFF SWITCH

POWER SUPPLY

Figure 15 Power Distribution

Page 33

‘CONTROL PANEL

COLOR MONITOR

REGULATOR! SPEAKER

AUDIO II PCB

z

¢

COIN DOOR VOLUME CONTROL ~ff TRAK BALLH DIR & CLK

TRAK BALL V DIR& CLK

‘START 1 LED

START 2 LED

GAME PCB

Figure 16 Signal Distribution

Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

Ihlustrated

Parts Lists

This chapter provides you with the necessary information for ordering replacement parts for your Centipede™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 36

037517-01 92-049 (Mon. Bezel) or 92-051 037515.01 fonion (Retainer) 71.2110 (Lock)

037522-01 (Mon. Shiela) 037511-02 (Rear Panel)

Controi Panel Assy.— see Figure 18

Mini-Trak Ball™— 178013-001 see Figure 19 (Latch) 037427-01 (Foam Pad)

037519-01 (Attract. Panel) 00246501 (Coin Cntr}

69-001 (SeltTest Sw.) 036891-01 (Spkr. Grille) 19-9032 (Vol, Ctrl.)

Coin Door— see Figure 23:

A037695-01 Anaranii (interi. Sw. & Brkt} ‘com Bo) 037696-01 (inter. Sw. Cyr.)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 78-320 CONFIDENTIAL: Reproduction forbidden without the spe- (Leg) Gific written permission of Atari, inc.. Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor session thereot confers or transfers any tight in, oF li cense to use, the subject ratter of the drawing or any de sign of technical information shown thereon, nor any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc,, and tor manufacture Under the corporation's wntten license, no right is granted to reproduce this drawing or the subject matter thereot, unless by written agreement with or written permission from the corporation.

Figure 17 Cabinet-Mounted Assemblies A037500-xx A

Page 37

Schematics, Self-Test Label & Manuals— 036686-01 see parts list on following page (Game Pricing Labels— not shown for clarity)

178034-024 (FMolding) 037501.01 (Cab't Assy.)

037528-01 (Mon. Brit.)

148001-001 (Speaker)

035745-03 (10-In. Retnr.) 037495-01 (Bracket) A037623-01 (Power Harness)

A037625-01 Reg/Audio 11 PCB— (Vol/Self-Test Hrns.) see Figure 20

A007638-01 037450-01 (Slam Sw) (Interl. Sw. & Brkt.) 007882.02 (Interl. Sw. Cvr.) 034536-03 (Vibra, Damper)

A037621-01 (Main Harness) Game PCB— see Figure 21

‘A037496-01 (Enclosure) 035745-02 (18:In. Retnr.)

Power Supply Assy. A037470-01 see Figure 22 (On/Off Sw. & Mntg. Plate) 009992-01 037243-01 (On/Oft Sw. Cvr.) (Plate)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc.. Sunnyvale, CA, This ‘drawing is only conditionally issued, and neither receipt nor possession thereot conters or translers any right in, oF li ense to use, the subject matter of the drawing or any de: sign or technical information shown thereon, nor any fight to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, Inc.. and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. A037453-03, A037454-03, or ———- | A037455-03 (Power Cord)

Figure 17 Cabinet-Mounted Assemblies A037500-xx A

Page 38

Figure 17 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A002465-01 Coin Counter A007638-01 Slam Switch Assembly A037450-01 Interlock Switch/Bracket Assembly (modified for safety—for rear access panel)

A037453-03Strain-Relief Power Cord(U.S.)
A037454-03Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly A037491-01 Coin Box A037496-01 Coin Box Enclosure A037621-01 Main Harness Assembly A037623-01 Power Harness Assembly A037625-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly A037695-01 Interlock Switch/Bracket Assembly (modified for safety—for coin door) The following six items are the technical information supplemenis to this game: DP-189-01 Centipede™/Cabaret™ Schematic Drawings (Sheet 1) DP-189-02 Centipede/Cabaret Schematic Drawings (Sheet 2) ST-189 Centipede/Cabaret Label with Self-Test Procedure and Option Switch Settings TM-160 Instruction and Service Manual for 19-Inch Electrohome Color Monitor, or TM-168 Instruction and Service Manual for 19-Inch Wells-Gardner Color Monitor TM-189 Centipede/Cabaret Operation, Maintenance and Service Manual 19-9032 Volume Control 69-001 DPDT Self-Test Slide Switch 71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-24012 5-Inch Beaded Nylon Tie Wrap (for game PCB edge connectors) 78-3201 Cabinet-Leveling Leg 92-049 19-Inch Electrohome Color Raster-Scan Monitor, or 92-051 19-Inch Wells-Gardner Color Raster-Scan Monitor 007882-02 Interlock Switch Cover 909992-01 On/Off Switch Cover 034536-03 Foam Vibration Damper (tor both PCBs) 035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer 036686-01 Card of Game Pricing Labels 036891-01 Speaker Grille 037243-01 Metal Base Plate (located underneath power supply) 037427-01 Rear Access Panel Foam Pad 03749501 Bracket for Volume Control, Self-Test Switch and Coin Counter(s) 037501-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) 037511-02 Rear Access Panel (does not include lock) 037515-01 Upper Monitor-Shield Retainer 037517-01 Blue Cardboard Monitor Bezel 037519-01 Attraction Panel with Graphics 03752201 Monitor Shield with Graphics 037529-01 Monitor Bracket (located above Regulator/Audio |! PCB) 037696-01 Interlock Switch Cover (for coin door) 148001-001 6x9Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker 178013-001 Spring Draw Latch 178034-024 %-\nch-Wide Black Plastic T-Molding

Page 39
NOTE: Graphics decal is not field-teplaceable.

Opp Centipede ™/Cabaret™

160013-001 75-9910NO (Leaf Sw/ ier 178030-001 (Stamped Nut) Batoneeet (Pushbtn. Assy) 78-6900402 160012-001 (Foam Tape) (Leat Sw. Only)

Mini-Trak Ball™ Assy.— see Figure 19

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- Giic written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof conters or transfers any right in, oli ‘cense 10 use, the subject matter of the drawing or any design of technical information shown thereon, nor any tight to reproduce this drawing of any part thereof. Except tor manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted 75-9910WO (Stamped Nut)

033127-01 (Sw. Bushing)

‘A037521.01 (Ctrl. Phi)

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the to reproduce this drawing or the subject matter thereof, un- 1 less by writen agreement with or written permission from rennet inside of the control panel. Only then the corporation, (Harness) should you lock up the game.

Figure 18 Control Panel Assembly A037505-01 A Parts List

Part No. Description

A037435-01 Control-Panel Harness A037521-01 Control Panel with Graphics Decal 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-9910NO #%-11 Steel Stamped Nut 75:9910W0 #'5,,-32 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, /-Inch wide x %-Inch thick (19 in. required) 033127-01 Black Molded Switch Bushing 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-001 Pushbutton Assembly

Page 40

Centipede ™/Cabaret™

176010-106 —F (6 PLACES) \ (Screw)

sN

036193-01 (Idler Shaft) le

75-014S (2 PLACES) ' (Washer)

(Washer)

72-8406, (2 PLACES) (Screw)

036192-01 (Lower Frame)

034168-01 (Label—not shown for clarity) 035938-01 (Wheel) LS NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atan, inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transiers any right in, or li ense to use, the subject matter of the drawing or any de: Sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof, Except for ‘manutacture by vendors of Atari, Inc,, and for manufacture under the corporation’s written license, no right 18 granted to reproduce this drawing or the subject matter thereof, un. less by written agreement with or written permission from the corporation.

+ 03619101 (Upper Frame)

035936-01 (Ball)

035937-01 ro) ee al Bearing) 035931-01 (Roller Shaft)

A036096-01 (Harness)

Figure 19 Mini-Trak Ball™ Assembly A036190-01

Page 41

Centipede ™/Cabaret™

Figure 19 Mini-Trak Ball"™ Assembly Parts List

Part No. Description A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 75-0148 #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-0448 #4 Zinc-Plated Steel Split Lock Washer 034168-01 Label with Lubrication Instructions

035931-01Roller Shaft(2 per assembly)

035936-01 Mini-Trak Ball™

035937-01Ball Bearing(6 per assembly)

035938-01 Etched Encoding Wheei 036191-01 Upper Black Plastic Frame 036192-01 Lower Black Plastic Frame

036193-01Idler Shaft(7 per assembly)

176010-106 #8 x %-Inch Cross-Recessed Pan-Head Thread-Forming Twin-Lead Zinc-Plated Steel Screw

Page 42

Centipede ™/Cabaret™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereo! confers or transfers any right in, oF license to use, the subject matter of the drawing or any de sign or technical information shown thereon, nor any sight to reproduce this drawing or any part thereof. Except tor manutacture by vendors of Atari, Inc., and for manufacture Under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereo! unless by written agreement with or written permission trom the corporation. ° 7 o_o g 5 =] 9 7 2 fu] Se C20 0 eo ay

C23 c3l fee} eee}

qriweh 22}

5.6K 308 Q9pe=s 7812 7905

o} —4R24,10,7WE oO

TIP 32 TOAZOO2A TDA2002A Q? BS crams cise R22 A cia 220 [R21 i/2w cle +h

COIR: enci(] RI

Figure 20 Regulator/Audio Il PCB Assembly A035435-02 E

Page 43

Figure 20 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P72.7 Ohm, +5%, 1W Resistor(R5)
16-54P04 Ohm, +5%, SW Wirewound Resistor(R25)
19-100P1015.10hm, +3%, 7W Wirewound Resistor(R24)
19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)
24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)

24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19)

245001051 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C22, 23)
29-088-1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C3, 11, 20, 21)
31-1N4002100V 1-Amp. Silicon Rectifier Type 1N4002 Diode(CR1, 4)
31-1N5401100V 3-Amp. Silicon Rectifier Type 1N5401 Diode(CR5-8)
33-TIP32PNP Power Transistor, Type TIP32(Q2)
34-2N3055,NPN Silicon Transistor, Type 2N3055(Q3)
37-LM305,5V Linear Voltage Regulator(Q1)
37-7812+12V Voltage Regulator, Type 7812(Q8)

37-7905 —5V Voltage Regulator, Type 7905 (Q9) 72-1608C #632 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6606S #6 x 9, Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screws (Q8) 75-F60405 #6-32 x %4-Inch Binder-Head Nylon Screw (Q85, 7) 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)
78-16014Thermally Conductive Silicon Insulator(Q2, 9)
79-583066-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)

79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink

100015-103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C5, C14)
110000-0101 Ohm, +5%, %4W Resistor(R10, 19)
110000-10010 Ohm, +5%, %W Resistor(R11, 20, 29, 30)
110000-101100 Ohm, +5%, %W Resistor(RA, 12, 22)
110000-1021K Ohm, + 5%, %W Resistor(R27, 28)

110000-103 10K Ohm, +5%, %W Resistor (R13, 14)

110000-271270 Ohm, +5%, Y4W Resistor(R1)
110000-33033 Ohm, +5%, VW Resistor(R3)
110000-3923.9K Ohm, +5%, YW Resistor(R6)
110000-5625.6K Ohm, +5%, ¥4W Resistor(R32, 33)
110000-75275K Ohm, +5%, ¥4W Resistor(R7)
110001-221220 Ohm, +5%, v2W Resistor(R9, 21)

116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17)

137151-002Type TDA2002A 8W Linear Audio Ampiifier Integrated Circuit(Q5, 7)
Page 44

+) oo] eles

A037241-01 Figure 21 Centipede™ Game PCB Assembly

Page 45

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) €012294-01 Audio /O N-Channel MOS/LS!I Custom Chip (C3)

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C83)

24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C52, 78)

24-5001051 mf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C79-82, 84, 86)
24-50010610 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C85)

29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 5-37, 40-51, 54-64, 66-77) 31-1NQ14 75V Type-1N914 Switching Diode (CRI, 2)

31-1N400175V Type-1N4001 Switching Diode(CR4, 5)

33-2N3906, Type-2N3906 PNP Switching and Amplifying Transistor (Q3)

34-2N3904Type-2N3904 NPN Silicon Transistor(Q1, 2, 4, 5)

34-2N6044 Type-2N6044 Darlington NPN Transistor (Q6-8)

37-LM324Type-LM324 Integrated Circuit(J10)
37-4584BType-4584B Integrated Circuit(F10, F11)
37-555,Type-555 Timer integrated Circuit(A11)
37-74LS00Type-74LS00 Integrated Circuit(L8)
37-74LS04Type-74LS04 Integrated Circuit(K3)
37-74LS08Type-74LS08 Integrated Circuit(B7, K4)
37-74LS10Type-74LS10 Integrated Circuit(L3, K2)
37-74LS20Type-74LS20 Integrated Circuit(A7)
37-74LS32Type-74LS32 Integrated Circuit(A4, C5, E3, F3, J3)
37-74LS42Type-74LS42 Integratéd Circuit(H3)
37-74LS74Type-74LS74 Integrated Circuit(D4, D11, M3)
37-74LS83Type-74LS83 Integrated Circuit(F6, H6)
37-74LS86Type-74LS86 Integrated Circuit(E7)
37-74LS90Type-74LS90 Integrated Circuit(L2)
37-74LS139Type-74LS139 Integrated Circuit(C4, J2)
37-74LS153Type-74LS153 Integrated Circuit(C7, E8, K6, L6, M6, N6, P6)

37-74LS157 Type-74LS157 Integrated Circuit (D7, D8, E11, F8, H8, J8, K8, P5)

37-74LS 163AType-74LS163A Integrated Circuit(A5, B5, M2, N2, N3, P2, P3)
37-74LS166Type-74LS166 Integrated Circuit(H9, J9)
37-74LS174Type-74LS174 Integrated Circuit(C6, D6, E6, J4)
37-74LS175Type-74LS175 Integrated Circuit(A8, E4, M4, N4)

37-74LS191 Type-74LS191 Integrated Circuit (B11, C11)

37-74LS244Type-74LS244 Intégrated Circuit(B1, C1, H5)
37-74LS245Type-74LS245 Integrated Circuit(E2)
37-74LS257Type-74LS257 Integrated Circuit(D9, E10, K9, L9, P7, M8, M9)
37-74LS259Type-74LS259 Integrated Circuit(M10)

37-74LS273 Type-74LS273 Integrated Circuit (B4, J6) 37-74LS373 Type-74LS373 Integrated Circuit (J5)

37-74LS374Type-74LS374 Integrated Circuit(H4)
37-74804Type-74S04 Integrated Circuit(N1)
37-74S74Type-74S74 Integrated Circuit(E9, F9)

37-7407 Type-7407 Integrated Circuit (A9, A/B10) 37-7815 + 15V Voltage Regulator (VR2) 37-7915 ~15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR3) [Continued on next page}

Page 46

Centipede ™/Cabaret™

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 41-3003 100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1-3)

62-001SPST Momentary Pushbutton Switch(Reset)
66-114P1T4-Station, Single-Throw, Dual-Inline-Package Bit Switch(N11)
66-118P1T8-Station, Single-Throw, Dual-Inline-Package Bit Switch(N8, N9)
79-42C1616-Contact Medium-Insertion-Force Integrated Circuit Socket(P4)
79-422222-Contact Medium-Insertion-Force Integrated Circuit Socket(E5)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(F7, H/J7, D1, £1, F/H1, J1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C2, C3)

81-4302 Nylon Snap-In Fastener

90-10212.096, + .005%, Crystal(¥1)

90-6013 Microprocessor (C2)

90-7005Random-Access Memory(C8)
90-7018Random-Access Memory(K5, K7, L5, L7, M5, M7, N5, N7)
90-7033Random-Access Memory(F2, H2)

020670-01 Test Point

110000-1021K Ohm, +5%, %4W Resistor(R9-11, 13-16, 23-28, 31-38, 55-60, 67, 68, 77, 79, 80, 87-89, 94,

95, 99, 104, 109, 114-123, 134, 136-141)

110000-10310K Ohm, +5%, YW Resistor(R1, 2, 6-8, 12, 17-22, 29, 30, 39-54, 70, 71)
110000-104110K Ohm, +5%, %W Resistor(R81, 82, 105, 106)
110000-105100 MegOhm, +5%, %4W Resistor(R5)

110000-152 1.5K Ohm, +5%, ¥4W Resistor (R108)

110000-221220 Ohm, +5%, %W Resistor(R3, 62, 64, 66, 72, 74-76, 78, 135)
110000-2222.2K Ohm, +5%, %W Resistor(R107)
110000-331330 Ohm, +5%, %4W Resistor(R61, 63, 65, 73)
110000-3323.3K Ohm, +5%, %4W Resistor(R69, 83-86, 103, 130-133)

110000-471 470 Ohm, +5%, %4W Resistor (R90-93, 96-98, 100, 110-113, 124-129, 142)

110000-56056 Ohm, +5%, %W Resistor(R101, 102)

119000-563 56K Ohm, +5%, %W Resistor (R4) 122002-102 .001 uf Ceramic-Disc 50V Radial-Lead Capacitor (C4) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C65) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C53)

128002-101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C1)
128002-221220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C38, 39)

128002-390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C2)

136001-201 or -211Read-Only Memory(F7)
136001-202 or -212Read-Only Memory(H/J7)
136001-203 or -207Read-Only Memory(D1)
136001-204 or -208Read-Only Memory(E1)
136001-205 or -209Read-Only Memory(F/H1)
136001-206 or -210Read-Only Memory(J1)
136001-213Programmable Read-Only Memory(P4)
137161-001Type-ER2055 Integrated Circuit(E5)Note: /f you replace this part, you must erase this ROM

before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions.

137169-001Type-74LS107 Integrated Circuit(LA)
137170-001Random-Access Memory(A6, B6) Acceptable substitute is part no. 90-7008 or 90-7035.
Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

Centipede ™/Cabaret™ 79-4411001 A037479-01 (Fuse Post) (Int'l. only) (Voltage Plugs) 03448202 037639-01 46-2017002

(Chassis)(Label)(Fuse)ee)men”

a» (Cover) (Fuses) rhein 79-3206 (Fuse Block)

A035891-01 (Fuse Harness)

78-2708 TOP VIEW (Hole Bushing)

46-301203 (Fuse)

NOTICE TO ALL PERSONS RECEIVING THIS, DRAWING: CONFIDENTIAL. Reproduction forbidden withaut the soe: 78-70501SC. cific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only Conditionally ssued, and neither feceipt nor (Capac. Bracket) 99.963 crag i ory on ta es oraters any ght ine ie Bense to use, the subject matter of the drawing or any de (Capacitor) Sign oF technical information shown thereon, nor any right torreproduce this. drawing or any part thereo!. Except for anulacture by vendors of Ata, Inc, and for manulacture tinder the corporation's written license, no right is granted A035888-01 or -02 to reproduce this drawing or the subject matter thereot un less by written agreement with of written permission from Cransformer) Jess by written 29 iG

BOTTOM VIEW

3A-MDA3501 (Rectifier)

A034630-01A035890-01A034629-0179-15021001
(RFI Fitter)(Pwr. Harness)(AC. Harness)(Term'| Block)

Figure 22 Power Supply Assembly A037671-01 (U.S.) A / A037671-02 (International) A

Page 49

Figure 22 Power Supply Assembly Parts List

Part No. Description (Reference Designations in Bold) A021084-01 Voltage Plug for 100V (violet) A021084-02 Voltage Plug for 120V_ (yellow) A021084-04 Voltage Plug for 220V (blue) A021084-05 Voltage Plug for 240V (brown) A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035888-01 or -02 Transformer Assembly (T1) A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, type MDA 3501 (CR1) 46-2014002 4-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %j,-Inch Outside Diameter x Y-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 037639-01 Label for Fuse Value (F1) 037641-01 Label for Fuse Values (F2-F6)

Page 50

99-1051 (Lamp Holder) Z

99-15026 (Coin Inlet) 99-15040 (Lever) 99-15056 (Screw for Bezel)

99-15054 99-15055 (Pivot for Lever) (Lockout Call) { 99-15053 (Lockt. Coil Spring)

99-15027 (Coin Ret. Box)

~—— 99-15028 (Coin Ret. Box)

99-15037 ° 7 (Sw. Adjuster) ia lo 99-15029 a (Bracket) < eo-1so4a-—~ 8 (Switch) 99-15056 (Screw for Bezel) 99-15060 a (Sw. Cover)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing 1s only conditionally issued. and neither receipt nor possession thereof confers or transfers any ‘ight in, of ficense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any pari thereof. Except for manutacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corporation.

Figure 23 Vertical-Mounted Coin Door A037619-xx B

Page 51

99-15067 (Lock Assy.)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe: Gific written permission of Atari, inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF li cense to use, the subject matter of the drawing or any de sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atani, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereo!, un less by written agreement with or written permission from ‘the corporation’

171004-001 — U.S. 25¢/25¢ Coin Door 171004-002 — U.S. 50¢/50¢ Coin Door 171004-003 — Canadian 25¢/25¢ Coin Door 171004.004 — British 10 P/10 P Coin Door 171004.005 — British 10 P/50 P Coin Door 171004-006 — British 20 P/50 P Coin Door 171004.007 — Australian 20/20¢ Coin Door 99-15067 (Lock Assy.)

99-15036 (Cover)

171004-008 — German 1 DM/1 DM Coin Door 171004.009 — German 2 DM/1 DM Coin Door 171004010 — German 2 DM/5 DM Coin Door 171004011 — German 1 DM/5 DM Coin Door 171004012 — 5 Fri5 Fr Coin Door 171004013 — Swiss 1 Fri1 Fr Coin Door 171004014 — French 1 Fri1 Fr Coin Door 99-15038 {Bezel for Button)

99-15001 thru 99-15012 (Ret. Button)

99-15052 (Spring for Button)

99-15065

99-15039 (Bezei for Cover)

i 99-15066 (Screw)

171004015 — French 2 Fri1 Fr Coin Door 171004016 — Swedish 1 Kr/1 Kr Coin Door 171004-017 — Spanish 25 Ptsi25 Pts Coin Door 171004-018 — Italian 100 L/100 L Coin Door 171004.019 — Hong Kong $1/$1 Coin Door 171004-020 — Japanese 100Y/100Y Coin Door

Figure 23 Vertical-Mounted Coin Door A037619-xx B

Page 52

Figure 23. Vertical-Mounted Coin Door, continued AS

Parts List

Part No. Description

A037542-01 Harness Assembly

99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover

99-15062 Hinge 99-15063 Screw for Hinge 99-15065 Clamp for Frame 99-15066 Screw for Clamp 99-15067 Lock Assembly

Page 53

YOUR COMMENTS, PLEASE! Contpteeabae

1st printing

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the USA.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name_.

Firm Oi Distributor

Address (3 Operator City _— State Zip U1 Other

Area Code Phone

Page 54

First fold

No Postage Necessary if mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 SE Second fold

i e a

Page 55

Buutruiieun & SUE PE TE GE TE ES

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted,

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

ES ES ES SS SS The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. ASAE ASABE AS

e

Page 56

A ATARI’ ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488 ©