CATHODE RAY TOMES

Atari System TM-286 1st Printing

Atari System I (Atari Games Corporation, 1984) · Technical Manual · 52 pages · 40 sections · original scan

Page 1

TM.286, Fst orinting w po J c £ § Bo) a Be ~~. @ 2 <= Qe O=

Page 2

Atari Games Corporation Customer Service

If reading through this manual does not lead to solving a maintenance or repair problem, call TELEHELP® at one of these Atari Games Customer Service offices:

UNITED STATES

Parts and Service

California Customer Service Office 737 Sycamore Drive P.O, Box 361110 Milpitas, CA 95035-1110 Telex 5101007850 (Monday-Friday, 7:30-4:00 pm Pacific Time) s (408) 434-3950

EUROPE

Parts and Service

European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) s 062-52155

Page 3

\ Operators Manual A With Illustrated Parts Lists

Page 4

© 1984, 1986 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A. 6Q System I

Page 5

Notice Regarding Non-ATARI® Parts

Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game. © Modify or alter any circuits in the game by using kits or parts zo¢ supplied by Atari Games Corporation. 7

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing, device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: ¢ All green ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet. ¢ The game printed-circuit boards (PCB) are properly installed with the Electromagnetic Interference (EMI) ground plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

system I

Table of Contents

Set-Up How to Use This Manual . Inspecting the Cabinet .. . Control and Switch Information Option Settings tee Power Supply Fuses .... 0... 00.6000 c eect eee eens

Maintenance Preventive Maintenance Preventive-Maintenance Intervals . Removing the Control Panel . . Cleaning ..

Corrective Maintenance Removing the Display Shield and Bezel . . Removing the Video Display . . Removing the Main PCB. ... . Removing the Fluorescent-Light Assembly .. Removing the Speakers

Troubleshooting Troubleshooting Aids Troubleshooting Techniques . Soldering Techniques ...... Troubleshooting Static-Sensitive Devices. . .

Illustrated Parts List See List of Illustrations that follows. 1-1 1-2 1-2 1-2 1-2

3-2 3-2 3-2

Page 7

List of Illustrations

Figure 1-1 Figure 1-2

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6

Table 1-1 Table 2-1 Control and Switch Locations Switching/Linear (SL) Power Supply Fuse Locations

Display Shield and Bezel Removal . Video Display Removal ..... LSI Main PCB Removal...... Fluorescent-Light Assembly Removal i Speaker Removal 0.0.0... 0c cece eect tee eee

Removing IC (Cut-Pin Method) ... Removing IC Pins Removing Solder from Plated-Through Holes . . Removing Solder from Lead Connection Pads. .

Cabinet-Mounted Assemblies .. 0... 60.66 cece eee eee ee Switching/Linear (SL) Power Supply mined eins Coin Acceptors, Inc. Coin Door or Assembly. PCB Mounting Hardware . tee LSI Main PCB Assembly . Audio II PCB Assembly

List of Tables

Installation Requirements Recommended Preventive-Maintenance Intervals . . 1-2 2-2 system I

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. A WARNING A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game’s power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, wellinsulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non-ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (i.e., United States) must not be operated in countries with 50 Hz line power (e., Europe). The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification label of your game for the line frequency required. System I
Page 9

‘WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you only have a two-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the cabinet is not properly grounded. Do not touch internal parts of the display with your hands or with metal objects.

Set-Up

How to Use This Manual

This manual is intended for game operators and service personnel. The information in this manual describes how to set up, maintain, and troubleshoot your Atari Games System I™ cabinet. Please refer to the game kit operators manual for information on the Cartridge Printed-Circuit Board (PCB) and the self-test of the game. Your System I cabinet is designed to accept the necessary hardware to easily convert the cabinet into a variety of games. Consequently, this manual contains information that applies to those parts of the System J cabinet that are common to all games. Information that applies to those parts that are replaced to convert the System I cabinet to a particular game are contained in a game kit operators manual that comes with each game kit. Where applicable, references are provided in this manual to the game kit Operators manual. This manual contains the following information on the System I cabinet: © Chapter 1 provides set-up information. © Chapter 2 provides preventive and corrective maintenance procedures. © Chapter 3 provides troubleshooting procedures.

  • Chapter 4 provides illustrated parts lists. Schematic diagrams of the System I cabinet circuitry are included as a supplement to this manual (SP-286). Refer to the Schematic Package Supplement included with the game kit operators manual for the game cartridge schematic, control-panel wiring diagrams, and any other diagrams pertaining exclusively to the game kit.

Chapter 1

Page 10

Set-Up

Inspecting the Cabinet

WARNING —A—— Do not plug in the cabinet until you have completed steps 1 through 3.

Please inspect your System I cabinet carefully to ensure that it has been delivered to you in good condition. Refer to Figure 4-1 for the location of the component parts of the cabinet. Table 1-1 lists space, power, and environmental requirements for the cabinet.

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Unlock and remove the front access panel. Unlock and open the coin door. From the top rear of the cabinet, remove the six attaching screws and lift off the rear access panel. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force conmectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void the warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets.

Table 1-1 Installation Requirements

Characteristic Requirement

Power Consumption 255 V-A, 210 W RMS typical with game components installed Temperature +5° to +38° C(+37° to + 100° F) Humidity Not to exceed 95% relative Line Voltage 105 to 132 VAC (or 200 to 264 VAC) Width 25.50 in. (64.6 cm) Depth 35 in, (89 cm) Height 70 in. (178 cm)

Weight 327 Ibs. (148 kg) maximum with

game components installed

1-2 System I

c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. (See Figure 1-2.) Check that the harness is plugged in correctly and that the fuse-block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the video display, printed-circuit boards (PCBs), speakers, and the fluorescent tube. Make sure they are mounted securely and that the green ground wires are connected.

Control and Switch

Information

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 4-1.) Volume Control The volume control is located on the Audio PCB. (See Figure 1-1.) The volume control adjusts the level of sound produced by the game. Coin Counters The coin counter(s) is located on the left wall of the cabinet behind the front access panel. (See Figure 4-1.) The coin counter(s) records the number of coins entered. Self-Test Switch The self-test switch is located on the Audio PCB. (See Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to the game kit operators manual for a complete description of self-test operation.

Option Settings

Refer to the self-test information in the game kit operators manual to set the options.

Power Supply Fuses

The power supply in your game contains three fuses. ‘When you replace a fuse, use the identical type fuse with the same electrical rating. (See Figure 1-2.) Also, be sure to put the replacement fuse in the correct location.

Page 11

system Set-Up

Volume Control

Figure 1-1 Control and Switch Locations

Page 12

Set-Up system I

Fuse Block Cover

WARNING —4—— Fuse block cover must be in place during game operation.

Figure 1-2 Switching/Linear (SL) Power Supply Fuse Locations

1-4

Page 13

Maintenance

This chapter includes preventive and corrective maintenance procedures for components that are common to all System I cabinets. References are provided, where applicable, to the Maintenance chapter in the game kit Operators manual for those components that are unique to a specific game. To assure maximum trouble-free operation from this game, we recommend that preventive maintenance be performed as described in this chapter and in the Maintenance chapter of the game kit operators manual. Removal, disassembly, reassembly, and replacement procedures are provided for System I cabinet components that may require corrective maintenance. Appropriate references are provided to Chapter 4, Illustrated Parts Lists, to aid in locating the parts of this cabinet that are mentioned, but not illustrated, in the maintenance procedures.

Page 14

Maintenance System I

Preventive Maintenance

Preventive maintenance includes cleaning the coin mechanism, interior components of the cabinet, and display shield. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 2-1 Recommended Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.

NOTE Refer to the Maintenance chapter in the game kit operators manual for preventive maintenance procedures for the player controls on the control panel.

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 2-1 are the recommended minimum requirements for the components listed.

To avoid possible electrical shock, turn off. and unplug the game before performing any maintenance procedures.

  • Re-seat the various connectors between the power supply and PCBs to ensure good electrical contact.
  • Verify correct video display adjustments using the selftest screens described in the game kit operators manual.

Removing the Control Panel

Refer to the Maintenance chapter in the game kit operators manual for control panel removal procedures.

Table 2-1 Recommended Preventive- Maintenance Intervals

Component Maintenance Interval

Coin Mechanism Clean at least every three months. Interior Components Clean at least every six months.

2-2

Cleaning

Cleaning the Coin Mechanism Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Display Shield The display shield can be cleaned with any non-abrasive household cleaner.

Cleaning the Interior Components Perform the following procedure to clean the electrical assemblies inside the cabinet.

Turn off the cabinet power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning tools.

  • Unlock and remove the front access panel from the cabinet.
  • Use a Phillips screwdriver to remove the six screws securing the display access panel to the top rear of the cabinet.
  • Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows.

a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

c. Wait two minutes and repeat part b.

Page 15

System I

CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paintbrush. Maintenance

4, Use a vacuum cleaner with a soft long-bristled brush attachment or a soft-bristled paintbrush to remove loose dirt and dust accumulation on the electrical assemblies inside the cabinet.

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, reassembly, and replacement of cabinet components. The following procedures are provided for components that may require corrective maintenance.

NOTE Refer to the Maintenance chapter in the game kit operators manual for the corrective maintenance procedures for the player controls.

Removing the Display Shield

and Bezel Perform the following procedure to remove/replace the display shield and bezel. (See Figure 2-1.)

  • Remove the control panel as described in the Maintenance chapter of the game kit operators manual.
  • Use a Phillips screwdriver to remove the two screws securing the speaker grille to the cabinet.
  • Grasp the display shield on the bottom edge and gently pull it out about one-half inch from the cabinet.
  • Gently lower the display shield to free it from the grooved molding under the attraction panel.
  • Use a flat-head screwdriver to remove the staples, if any, securing the bezel to the cabinet.
  • Remove the bezel.

Removing the Video Display

A WARNING —_A—_, High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on highvoltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube can implode if struck or dropped. Shattered glass can cause injury within a six-foot radius. Use care when handling the display.

Perform the following procedure to remove/replace the video display. (See Figure 2-2.)

  • Turn the game power off and wait two minutes. Unplug the power cord.
  • Use a Phillips screwdriver to remove the six screws securing the upper rear access panel to the cabinet.
  • Remove the display shield and bezel as previously described.
  • Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end ofa large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

c. Wait two minutes and repeat part b.

  • From the back of the cabinet, unplug the display-harness connectors and disconnect the ground wire.
Page 16

Maintenance

Speaker Grille System I

Figure 2-1 Display Shield and Bezel Removal

To avoid dropping the video display, use extreme care when removing the display from the cabinet. We recommend that a second person carefully hold the display chassis from the back of the cabinet while the other person lifts it from the front of the cabinet.

  • From the front of the cabinet, use a 3/8-inch wrench to remove the four nuts and washers securing the display to the cabinet.
  • Carefully slide the display out through the front of the cabinet.
  • Replace the display in the reverse order of removal.
NOTE Whenever the cathode-ray tube is replaced, readjust the brightness, purity, and convergence as described in the display manual.

Removing the Main PCB

Perform the following procedure to remove/replace the Main PCB. (See Figure 2-3.)

NOTE The procedure for removing the Cartridge PCB is included in the Maintenance chapter of the game kit operators manual.
  • Turn the cabinet power off.
  • Unlock and remove the front access panel from the cabinet.
  • Disconnect the harness connectors from the Main PCB. . 4, Use a Phillips screwdriver to remove the four screws securing the ground plane to the cabinet.
  • Carefully remove the ground plane, with the PCBs attached, and place on a clean surface.
  • Use a Phillips screwdriver to remove the four screws securing the Main PCB to the ground plane.
  • Gently disconnect the Main PCB from the Cartridge PCB.
Page 17

System I

Display Mounting Studs

Video Display Maintenance

Rear Access Panel

Figure 2-2 Video Display Removal

  • Replace the Main PCB in the reverse order of removal. Make sure that the Main PCB is fully inserted into the Cartridge PCB edge connectors and the ground strap is properly connected to the ground plane. Refer to Figure 2-3 for the ground strap and harness connector locations.

Removing the Fluorescent-

Removing the Fluorescent Light Assembly

Perform the following procedure to remove/replace the fluorescent-light assembly. (See Figure 2-4.) 1, Turn the game power off.

  • From the rear of the cabinet, use a Phillips screwdriver to remove the six screws securing the upper rear access panel to the cabinet.
  • Disconnect the fluorescent-light harness connector.
  • From the front of the cabinet, use a 1/8-inch hex driver to remove the three screws securing the attraction retainer to the top of the cabinet.
  • Grasp the top edge of the attraction shield and film and lift out of the cabinet.
  • Gently twist the fluorescent tube a quarter turn and remove from the sockets.
  • Use a Phillips screwdriver to remove the two screws securing the fluorescent-light bracket to the cabinet.
  • Lift the fluorescent-light assembly out of the front of the cabinet.
  • Replace the fluorescent-light assembly in the reverse order of removal.

Removing the Speakers

Perform the following procedure to remove/replace the speakers, (See Figure 2-5.)

  • Remove the control panel as described in the Maintenance chapter of the game kit operators manual.
  • Use a Phillips screwdriver to remove the two screws holding the speaker grille to the cabinet and the four screws securing each speaker to the cabinet.
CAUTION Do not touch the speaker cones when handling the speakers. The cone material is fragile and can be easily damaged.

2-5

Page 18

System I Maintenance

Ki

ee = Main PCB Assy Ground Strap

Ground Plane

bp + i

oe

Cartridge PCB Assy

Figure 2-3 Main PCB Removal

4, Replace the speaker in the reverse order of removal. 3, Lift the speaker out just far enough to disconnect the Ensure that the speakers are properly phased by plactwo speaker wires from the back of the speaker. ing the same color-coded connector on the same tab on each speaker.

Page 19

System I

Retainer

Attraction Shield

a Attraction Film

Figure 2-4 Fluorescent-Light Assembly Removal Maintenance

‘Speaker

‘Speaker Grille

Figure 2-5 Speaker Removal

2-7

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Troubleshooting

The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.

NOTE ‘We recommend that troubleshooting and repair procedures be performed by a qualified service technician.
Page 22

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the schematic package supplement, and also in the game kit operators manual and its schematic package supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The parts lists in Chapters 4 of this manual and in the game kit operators manual illustrate the locations of assemblies and components, Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).

Diagrams The schematic package supplement for this manual and for the game kit operators manual contain schematic diagrams with component locations, active component type numbers, and electrical values.

Troubleshooting Techniques

To avoid electrical shock, turn off the game power before attempting to troubleshoot this game.

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.

Check Fuses Check for open fuses. Refer to the power supply parts list in Chapter 4 and to the Display Manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Powet-Supply Voltages

Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.

Localize Trouble Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Per-

3-2 system I

form the self-test procedure provided in the game kit operators manual.

Visual Check Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.

Check Individual Components Check soldered-in passive components (e.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.

Repair the Assembly

CAUTION Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and transistors.

Repair or replace the defective part. Refer to Chapter 2 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.

Soldering Techniques

Observe the following recommendations when removing or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components. Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage- sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information. A15- to 27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controlled soldering station rated at

Page 23

system I

700°F with a fine cone or a very fine chisel tip can also be used.

CAUTION Solder guns are not recommended for removing or replacing soldered-in components on a printed-circuit board. The added possibility for overheating and the large transient voltage induced by the solder gun could cause damage to heat- or voltage-sensitive devices.

The following additional equipment is recommended for removing and replacing soldered-in components: © Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. © Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multilayer PCB with plated-through holes. Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropy] alcohol is recommended. ¢ Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits

The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 3-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each

Diagonal Cutter

Figure 3-1 Removing IC (Cut-Pin Method) ‘Troubleshooting

pin in a random order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown in Figure 3-2. Allow a moment for the PCB to cool before proceeding to the next pin. Apply just enough heat to remove any stubborn pins. For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 3-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 3-4.

CAUTION Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

Use an integrated-circuit (IC) pulling tool to remove socketed ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.

Troubleshooting Static-

Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, ¢.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.

Needle-Nose Pliers

Soldering Iron

Figure 3-2 Removing IC Pins

Page 24

Troubleshooting

Solder Sucker

Preferred Method Soldering Iron System I

Solder Sucker

Soldering Iron

Alternate Method

Figure 3-3 Removing Solder from Plated-Through Holes

Soldering Iron Solder Wick

Figure 3-4 Removing Solder from Lead Connection Pads

Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped

3-4 around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When.soldering on a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) Astatic-sensitive device can appear defective due to leakage on a PCB. Observe the precautions for grounding static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover or an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Page 25

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCBs) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator or location. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers appear first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help us fill your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 4

Page 26

Illustrated Parts Lists

042890-01 %, or 0043187-01 x, or 042890-51 % © 0043187-51 Shield 042892-01 *, or a 042892-51 ® 043196-01 *, or 043196-51 System I

043276-01 x, or Attraction Shield Retainer YY

042891-01 *, or 042891-51 Attraction Shield attraction Film Display Bezel 139017-002 ‘A043606-51 ADI (Disco) Display, or 139017-001 Wells-Gardner Display al 042896-01 x, or 042896-51 $ Speaker Grille See Game Kit Manual

78-6900402 N Foam Tape—not shown Z @

S

Control Panel Assy See Game Kit Manual

148004-002 Speaker

A038881-01 176013-001 Lock Assy Spring Draw Latch Q 042907-01 *, or “ 042907-51 #. Front Access Pane! a Coin Doors A043455-01 x, or See Figures 4.3 A043455-51 AC Harness Assy

Figure 4-1 Cabinet-Mounted Assemblies A043480-01 C and A043480-51 C

4-2 042910-01 x, or 042910-51 Rear Access Panel Y

|A042881-02 *, or ‘A042881-52 % Cabinet Assy

038091-01 Coin Box

78-3201 Adjustable Glide

Page 27

system I Mlustrated Parts Lists

+ Part used only in US-built cabinets 4% Part used only in Iretand-built cabinets

A043456-01 *, or A043456-51 woe Coin Harness Assy A043086-01 *, or ‘A043086-51 % Display Harness Assy Ground Strap Assy

A043457-01 *, or D A043457-51 Speaker Harness Assy

042914-01 x, or 042914-51 & Fan Grille

LSI Main PCB Assy ‘A043055-01 *, or ; ‘A043055-51 See Figure 45 On/Off Switch w/ Harness Assy ——ae|

Audio II PCB Assy 042931-01 *, or See Figure 4-6 042931-51 & PCB Ground Plane Plate

171078-002 Cartridge PCB Assy Coin Counter See Game Kit Manual

L_—= Power Supply Assy See Figure 4-2 A043454-01 *, or A043454-51 & Power Harness Assy

043513-01 Power Supply Ground Plane Plate

Figure 4-1 Cabinet-Mounted Assemblies, Continued A043480-01 C and A043480-51 C

Page 28

Illustrated Parts Lists System I

Cabinet-Mounted Assemblies Parts List

Part No. Description

A038881-01 * Lock Assembly A042881-02 * Cabinet Assembly (A042881-52 #)

US-Built Fluorescent Light Panel Assembly Only A042884-01 * Fluorescent Light Panel Assembly—consists of: A005493-01 Light Harness Assembly A037540-01 Ground Jumper Assembly 70-304 18-Inch, 15 W, Cool White Fluorescent Tube

72-64088 #4 x ¥s-Inch Pan-Head Cross-Recessed Tapping Screw 79-561816P *& Wire Nut 99-11003 * Starter 99-11006 Retaining Clip

99-11009 * Starter Socket 038151-01 * Jumper Wire 041981-01 * Lamp Bracket 042920-01 * Attraction Glass Panel

142028-001 * 60 Hz Ballast Transformer 176015-110 * #10 x 5/8-Inch Pan-Head Cross-Recessed Deep-Thread Screw 179035-001 * Medium Bi-Pin Lamp Holder

Ireland-Built Fluorescent Light Panel Assembly Only A043606-51 % Fluorescent Light Panel Assembly—consists of: A005493-02 Light Harness Assembly 70-303 @ 18-Inch, 15 W, Cool White Fluorescent Tube 72-6610S # #6 x 5/8-Inch Pan-Head Cross-Recessed Tapping Screw

79-561816P $ Wire Nut 99-11012 & LInch Clamp 035835-01 # 12-Inch Y-Lead Connector 042920-51 ® Attraction Glass Panel

142043-001 # 220 V Ballast Transformer 171079-001 # 220 V Starter 179220-001 # 220 V Starter Socket

A043035-01 Display Harness Assembly (A043035-51 #) A043055-01 * On/Off Switch with Harness Assembly (A043055-51 ) A043086-01 Ground Strap Assembly, 8% Inches Long, attached to Main LSI PCB ground plane plate (A043086-51 #) A043086-03 Ground Strap Assembly, 4% Inches Long, attached to control panel (A043086-53 #)

A043454-01 * Power Harness Assembly (A043454-51 @) A043455-01 & AC Harness Assembly (A043455-51 ) A043456-01 Coin Harness Assembly (A043456-5 1 #) A043457-01 * Speaker Harness Assembly (A043457-51 #)

78-3201 Adjustable Glide 78-6900402 1/4-Inch x 1/8-Inch Foam Tape (48 inches required; used on control panel and attraction glass) 99-15066 Screw Clamp 038091-01 Molded Coin Box

042890-01 * Display Shield (042890-51 #) 042891-01 * Attraction Shield (042891-51 #) 042896-01 * Speaker Grille (042896-51 #) 042907-01 * Front Access Panel (042907-51 #)

4-4

Page 29

System I Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, Continued

Part No. Description

042910-01 * Rear Access Panel (042910-51 #) 042914-01 * Fan Grille (042914-51 @) 043187-01 * Horizontal Display Bezel (043187-51 §); Acceptable substitute is part no. 042892-01 * (042892-51 #) 043196-01 Vertical Display Bezel (043196-51 #)

043276-01 * Attraction Shield Retainer (043276-51 #) 043513-01 Power Supply Ground Plane Plate 139017-002 ADI (formerly known as Disco) 19-Inch Color Raster Display (Model DMC 2090DT-2C) OR 139017-001 ‘Wells-Gardner 19-Inch Color Raster Display (Model 19K4914)

148004-002 4¥%-Inch Round, 8 Q, 10 W Speaker 171078-002 Non-Resettable Coin Counter, 12 VDC 176013-001 Spring Draw Latch 178093-001 Fan Guard

The following are technical information supplements to this game: TM-210 ADI (formerly known as Disco) 19-Inch Color Raster Display Manual TM-283 Wells-Gardner 19-Inch Color Raster Display Manual TM-286 Atari System I Operators Manual SP-286 Atari System I Schematic Package Supplement

CO-210-01 ADI 19-Inch Color Raster Display Service Manual Supplement CO-286-01 Atari System I Operators Manual and Schematic Package Supplement

  • Part used only in US-built cabinets Part used only in Ireland-built cabinets
Page 30

Illustrated Parts Lists system I

NOTE Part used only in US-built cabinets A043365-01 Some 5V switching power supply assem- 4$Part used only in Iretand-built cabinets DC Pack SV Switching Power bles can be placed on their side, or fatto Supply Assy, or the chassis base (not shown). ‘A043365-02 Toko America 5V Switching Power Supply Assy 72-1806S

179231-002 Terminal Block

aoasae7.01 2 — 142042-001 *, or Jumper Assy ue Be ua0Ht-001 or 142041-101 Transformer

043396-01 Power Supply Chassis Base

Line Filter Assy

ra!

46-2013002 Fuse

72-HA4606S Screw

037640-01 79-3206 Label Fuse Block 034544-01 Fuse Block Cover

46-2032002 Fuse

Figure 4-2 Switching/Linear (SL) Power Supply Assembly A043363-01 D

Page 31

system I Illustrated Parts Lists

Switching/Linear (SL) Power Supply Assembly Parts List

Part No. Description

A042384-01 Line Filter Assembly A043365-01 DC Pack Co. Ltd. 5V Switching Power Supply Assembly A043365-02 ‘Toko America, Inc. 5V Switching Power Supply Assembly A043367-01 Jumper Assembly

46-2013002 250 V Slow-Blow 3 A Fuse 46-2032002 250 V Normal-Blow 2 A Fuse 72-HA4606S #6-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-1806S #8-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 79-3206 5-Position Fuse Block 034544-01 Fuse Block Cover 043385-01 Power Supply Label (Fuses) 043396-01 Power Supply Chassis Base

142042-001 * Transformer (142042-101 ); Acceptable substitute is part no. 142041-001 * (142041-101 ) 179231-002 2-Position Terminal Block

The following items are technical information supplements to this game: CO-284-01 Schematic and Spare Parts List for DC Pack Co. Ltd. SV Power Supply CO-284-04 Schematic and Spare Parts List for Toko America, Inc. 5V Power Supply

  • Part used only in US-built cabinets # Part used only in Ireland-built cabinets
Page 32

Illustrated Parts Lists System I

99-10140 Panel Assembly 75-9488 Locknut

99-10152 Right Coin Inlet y

171006-035 99-10116 Lever

99-10147 Harness

99-10151 Left Coin Inlet

99-10080

99-10105 Bar

99-10104 Bar Retainer

99-10042 thru 99-10045 99-10154 Coin Switch Assembly

99-10150 Switch Cover

Coin Chute 65-4410 Coin Switch _~ 99-10075 thru 99-10078 Switch Wires 99-1008 Retainer 75-14128

Screw

Figure 4-3 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 33

Illustrated Parts Lists System I

99-10148 Lock Assembly

99-10142 Button Housing 72-HA1404C Screw

99-10134 99-1019 Cover 99-10139 ’ Coin Door : < Button Assembly | 9.10118 Button

7 ° 99-0115 99-10148, Spring Lock Assembly s

~ : SS : 99-10141 % : i Coin Return Cover gS - : 99-10117 Coin Return Door

72-JA1405B | : Screw . |——_99-10144 Channel Clip od 99-15066 Screw

P 99-10149 : Service Door 038091-01 F Coin Box q

, 99-10143 : Frame

NOTE Acceptable alternate or substi- if tute coin door assembly is part i] number 171034-001. |

Figure 4-3 Coin Acceptors, Inc. Coin Door Assembly, continued 171027-001 A

Page 34

Illustrated Parts Lists. system I

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description

65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406 #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x ¥4-Inch Pan-Head Screw

72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-1412S #4-40 x 34-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer

99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P

99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
99-10077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover

99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing

99-10143, Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly

99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet

99-10153 Coin Return Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. $.25

4-10

Page 35

System I Ulustrated Parts Lists

N O T E S

Page 36

Illustrated Parts Lists

72-1610S Screw

LSI Main PCB Assy See Figure 45

+s

034536-10 Foam Damper

034536-11 Cartridge PCB Assy Nf Foam Damper ‘See Game Kit Manual

176031-2616 Thumb Screw 042931-01 Ground Plane System I

175004-708 Fiber We #8 Fiber Washer 176015-112 #10 Screw ‘Audio Il PCB Assy See Figure 4-6

Figure 4-4 PCB Mounting Hardware A042932-01

4-12

Page 37

System I Illustrated Parts Lists

PCB Mounting Hardware Parts List

Part No. Description

A043096-21 Atari System I LSI Main PCB Assembly—see Figure 4-5 A043661-02 Audio II PCB Assembly—see Figure 4-6 72-16108 #6-32 x 5/8-Inch Cross-Recessed Pan-Head Machine Screw 75-0168 #6 Flat Washer

034536-10 3 x 6 x .62-Inch Foam Vibration Damper 034536-11 3 x 6x .81-Inch Foam Vibration Damper 042931-01 PCB Ground Plane 175004-708 #8 Fiber Washer

176015-112 #10 x 3/4-Inch Cross-Recessed Pan-Head Deep-Threaded Screw 176031-2616 #6-32 x 1/2-Inch Brass Knurled Thumb Screw

Page 38

Illustrated Parts Lists

‘or any design or technical informat vendors. System 1

ICE TO ALL PERSONS RECEIVING THIS DRAWING jon shown thereon, nor any right to part ‘of Atari Games Corporation, and for manufacture under the corporation's writen license, no right is granted to reproduce this, this drawing or ‘or the subject matter thereof, unless by writen agreement with or writen permission from the corporation.

Eom,¢ BeeSEES FmvenSFoumnEe
~s|Blaw=0003000Gist,oTmOrga)
«if“Eei—thud, a a™ae!
Breaker coe“2.785SSAea)
=aa,=
weUBa2toeoe& By“sa=
cE>Seeag—
=a,Areece A cscsosesee)
~fe"—FuessassSsware”
n=fp ams FfFra5fF]
oeneAsrsev-apesshiney aasresset
.Paar abeah“=||==
ies eee ll Boot"us&sscase-st2
tea RolFadi asa)ae
eiretsgots——
5oewosmase-i3a

or pel << smut te

a2afwoBYBb

BR wo

Peoe]weBe
i.=wsom
Lest18158harLexyio5men]
vueveea]
ss=ota

fe

jcltmetcansaarstanewytsrevase:
aaatsumemomanueme amuenon
a asoSa.

ee ee

"aroo=
a‘sinsomeascoBEusinsomane
1zz]TNE1

pd oe

Boweieancs
anaet
bobamOpFathfh+ i
DoOQOomamPscox

Figure 4-5 LSI Main PCB Assembly A043096-21 C

Page 39

System 1 Illustrated Parts Lists

LSI Main PCB Assembly Parts List

DesignatorDescriptionPart No.

Integrated Circuits

1/2AType-74LS74 Integrated Circuit37-74LS74
1/2BType-74LS194 Integrated Circuit37-74LS194
1BType-74LS194 Integrated Circuit37-74L8194
1cCustom Integrated Circuit137419-101
1FType-74LS86 Integrated Circuit37-74LS86
1HType-74S283 Integrated Circuit137204-001
WKCustom Integrated Circuit137419-104
ILType-74S02 Integrated Circuit37-74802
23BType-2364A, 300 ns PROM Integrated Circuit (Acceptable substitute is136032-104

part no. 136032-107)

2cType-74LS174 Integrated Circuit37-74LS174
2DType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
2EType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
2FType-74LS174 Integrated Circuit37-74LS174
2HType-748283 Integrated Circuit137204-001
2Type-74S374 Integrated Circuit137206-001
2KType-745374 Integrated Circuit137206-001
2LType-74LS244 Integrated Circuit37-T4LS244
3/4A1024 x 4, 55 ns MOS Static RAM Integrated Circuit137199-001
3/4B1024 x 4, 55 ns MOS Static RAM Integrated Circuit137199-001
3cType-74LS273 Integrated Circuit37-7ALS273,
3DType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
3EType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
3FType-74L$273 Integrated Circuit37-74LS273,
3HType-74S283 Integrated Circuit137204-001
3J1024 x 4, 45 ns MOS Static RAM Integrated Circuit137199-002
3K1024 x 4, 45 ns MOS Static RAM Integrated Circuit137199-002
3LType-74LS244 Integrated Circuit37-74LS244
4cType-74LS151 Integrated Circuit37-74L8151
4DType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
4EType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
4FType-74LS273 Integrated Circuit37-74LS273,
4HType-74S283 Integrated Circuit137204-001
4y1024 x 4, 45 ns MOS Static RAM Integrated Circuit137199-002
4K1024 x 4, 45 ns MOS Static RAM Integrated Circuit137199-002
4LType-74820 Integrated Circuit137423-001
SIGAType-74LS245 Integrated Circuit37-TA4LS245
5/6BType-74L5245 Integrated Circuit37-7ALS245
5A1024 x 4, 55ns MOS Static RAM Integrated Circuit137199-001
5B1024 x 4, 55ns MOS Static RAM Integrated Circuit137199-001
5CType-74LS244 Integrated Circuit37-74L8244
5DType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
SEType-1MS1420, 55 ns Static RAM Integrated Circuit137360-001
SFType-74LS273 Integrated Circuit37-74LS273,
SHType-74LS32 Integrated Circuit37-74L832
Page 40

Ilustrated Parts Lists system I

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart
5y/KCustom Integrated Circuit137419-102
SK/LType-74LS00 Integrated Circuit37-7ALS00
SLType-74S08 Integrated Circuit37-74S08
6AType-74LS273 Integrated Circuit37-74LS273
6BType-74L$273 Integrated Circuit37-74LS273,
6cType-74LS191 Integrated Circuit37-74LS191
6DType-74LS153 Integrated Circuit37-74LS153
6EType-74LS153 Integrated Circuit37-74LS153
OFType-74LS244 Integrated Circuit37-74LS244
oHType-74LS244 Integrated Circuit37-74L8244
9gType-74LS257 Integrated Circuit37-741$257
6KType-74LS257 Integrated Circuit37-74L8257
QIKCustom Integrated Circuit137419-102
6LType-74LS257 Integrated Circuit37-74LS257
7AType-7407 Integrated Circuit37-7407
7BType-7407 Integrated Circuit37-7407
7CType-74LS191 Integrated Circuit37-74L8191
7DType-74LS153 Integrated Circuit37-74LS153,
JEType-74LS153 Integrated Circuit37-74LS153
TFType-74L$373 Integrated Circuit37-74L8373
7HType-74LS373 Integrated Circuit37-7ALS373,
aType-74LS32 Integrated Circuit37-74L832
7KType-74LS 139 Integrated Circuit37-74LS139
7LType-74LS374 Integrated Circuit37-74LS374
8AType-748260 Integrated Circuit37-748260
8BType-7407 Integrated Circuit37-7407
8CType-74LS191 Integrated Circuit37-74LS191
8DType-74LS153 Integrated Circuit37-74LS153
8EType-74LS153 Integrated Circuit37-74LS153
8FType-74LS368A Integrated Circuit137168-001
8HType-74LS74 Integrated Circuit37-7ALS74
8)Type-74LS138 Integrated Circuit137177-001
8kType-74LS32 Integrated Circuit37-74LS32
8LType-741874 Integrated Circuit37-74LS74
9CType-74LS273 Integrated Circuit37-74LS273
9DType-74LS74 Integrated Circuit37-74LS74
9ECustom Integrated Circuit137419-103
9HType-74L$32 Integrated Circuit37-7ALS32
xyType-7407 Integrated Circuit37-7407
9KType-74LS08 Integrated Circuit37-74LS08
10CType-74LS02 Integrated Circuit37-74LS02
10DType-74874 Integrated Circuit37-74S74
10EType-74S240 Integrated Circuit137416-001
10FType-74LS245 Integrated Circuit37-74LS245

4-16

Page 41

System I Ilustrated Parts Lists

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
10)Type-23128A, 200 ns PROM Integrated Circuit (Acceptable substitute is136032-113

part no. 136032-115)

10KType-74LS14 Integrated Circuit37-74L814
10LType-74LS197 Integrated Circuit137240-001
11Type-74LS163A Integrated Circuit37-7ALS163A
11EType-74LS245 Integrated Circuit37-74LS245,
11FType-74LS245 Integrated Circuit37-74LS245,
1yType-23128A, 200 ns PROM Integrated Circuit (Acceptable substitute is136032-112

part no. 136032-114)

11KType-74LS245 Integrated Circuit37-7ALS245,
11LType-74L8245 Integrated Circuit37-74LS245
12CLETA Integrated Circuit137304-1001
12EType-74LS20 Integrated Circuit37-74LS20
12FType-74L5138 Integrated Circuit137177-001
12HType-68010-L8 Microprocessor137414-001
12)Type-74LS244 Integrated Circuit37-74LS244
12K2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
12L2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
13Type-ADC0809 Integrated Circuit137243-001
13DType-74LS368A Integrated Circuit137168-001
13EType-2804, 450 ns EPROM Integrated Circuit137329-450
13EType-74L832 Integrated Circuit37-74LS32
13)Type-74LS244 Integrated Circuit37-74LS8244
13K2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
13L2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
14CType-74L8244 Integrated Circuit37-7ALS244
14DType-74LS138 Integrated Circuit137177-001
14EType-74LS374 Integrated Circuit37-74LS374
14FType-74LS259 Integrated Circuit37-74LS259
14HType-74LS245 Integrated Circuit37-74LS245
14)Type-74L$139 Integrated Circuit37-74L$139
14KType-74LS244 Integrated Circuit37-74LS244
14L2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
15CType-74LS367A Integrated Circuit37-74LS367
15EType-74LS374 Integrated Circuit37-74LS374
15HType-74LS138 Integrated Circuit137177-001
15)Type-74LS00 Integrated Circuit37-74LS00
15KType-74LS244 Integrated Circuit37-74LS244
15L.2048 x 8, 150 ns Static RAM Integrated Circuit137211-001
16DType-LM324 Integrated Circuit37-LM324
16EType-LM324 Integrated Circuit37-LM324
16F‘Type-LM324 Integrated Circuit37-LM324
16)/KType-6502A Microprocessor90-6013
16HType-74LS74 Integrated Circuit37-74LS74
16L.Type-74LS245 Integrated Circuit37-74L8245
17FType-YM3012Integrated Circuit137402-001

4-17

Page 42

Ilustrated Parts Lists system I

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
17HType-YM2151 Integrated Circuit137401-001
ATKCustom Integrated CircuitCO12294
17LType-74LS148 Integrated Circuit137417-001

Capacitors

cl100 uF, 25 V Electrolytic Capacitor24-250107
C2.1 pF, 50 V Ceramic Capacitor122002-104
C3-C5,470 pE, 50 V Ceramic Capacitor122013-471
C6-C81000 pF, 100 V Ceramic Capacitor122016-102
co-1 wE, 50 V Ceramic Capacitor122002-104
C10-C17.O1 wF, 25 V Ceramic Capacitor122005-103
C18-C40.1 wE, 50 V Ceramic Capacitor122002-104
C410 uF, 25 V Electrolytic Capacitor24-250106
C42-C58.1 pF, 50 V Ceramic Capacitor122002-104
C59.01 pF, 25 V Ceramic Capacitor122005-103
C60.01 wE, 25 V Ceramic Capacitor122005-103
C6139 pE, 100 V Mica Capacitor128002-390
C62100 pF, 100 V Mica Capacitor128002-101
C63.1 pF, 50 V Ceramic Capacitor122002-104
C641000 pF, 100 V Ceramic Capacitor122016-102
C651000 pF, 100 V Ceramic Capacitor122016-102
C66-1 wE 50 V Ceramic Capacitor122002-104
C67-1 wE 50 V Ceramic Capacitor122002-104
C681000 pF, 100 V Ceramic Capacitor122016-102
coo1000 pF, 100 V Ceramic Capacitor122016-102
c70-1 gE, 50 V Ceramic Capacitor122002-104
C71.1 wE, 50 V Ceramic Capacitor122002-104
C72.001 wE, 50 V Ceramic Capacitor122002-102
C7310 uF, 25 V Electrolytic Capacitor24-250106
C741000 pF, 100 V Ceramic Capacitor122016-102
C751 pF, $0 V Electrolytic Capacitor24-500105
C761 wE, 50 V Electrolytic Capacitor24-500105
C770027, 50 V Ceramic Capacitor122015-272
C78.0027, 50 V Ceramic Capacitor122015-272
C791 wE, 50 V Electrolytic Capacitor24-500105
C80-1 wE, 50 V Ceramic Capacitor122002-104
C81-1 nF 50 V Ceramic Capacitor122002-104
C82-C8410 uF, 25 V Electrolytic Capacitor24-250106
C85-C154.1 pF, 50 V Ceramic Capacitor122002-104
C15510 uF, 25 V Electrolytic Capacitor24-250106
C15610 pk 25 V Electrolytic Capacitor24-250106
C158-C160.1 wE, 50 V Ceramic Capacitor122002-104

Diodes

CRI, CR2Type-IN4148 Diode131033-001
CR3Type-MV5053 Diode38-MV5053,
CR4Type-IN754A Diode131002-001
CRSType-MV5053 Diode38-MV5053,

4-18

Page 43

System I Illustrated Parts Lists

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.

Connectors

CP1, CP280-Position Card Edge Connector179221-180
Jio112-Position Header Connector179069-012
J102-J10411-Position Square Pin Header Connector179118-011
J1056-Position Square Pin Header Connector179118-006
J10611-Position Square Pin Header Connector179118-011
J1075-Position Square Pin Header Connector179118-005
J1088-Position Square Pin Header Connector179118-008

Inductors

Ll68 wH Inductor141016-008
L2-L41 pH Inductor141007-001
LS100 #H Inductor41-3003

Transistors

a‘Type-2N3906 Transistor33-2N3906
Q2Type-2N3643 Transistor34-2N3643
Q3-O5Type-2N3904 Transistor34-2N3904
Q6-Q8Type-2N3906 Transistor33-2N3906
Q9, Q10Type-2N6044 Transistor34-2N6044
Q11-Q13Type-2N3904 Transistor34-2N3904

Resistors

RL5100, +5%, 4 W Resistor110000-511
R2680, +5%, % W Resistor110000-680
R3-RO270, +5%, 4 W Resistor110000-270
R720kQ, +5%, % W Resistor110000-203
RS10kQ, +5%, % W Resistor110000-103
RO4.99kQ, +1%, % W Resistor110011-502
R102.49kQ, +1%, % W Resistor110011-252
R11-R141000, +5%, 4 W Resistor110000-101
RIS2.2kQ, +5%, % W Resistor110000-222
R16-R193300, +5%, % W Resistor110000-331
R202.2 kQ, +5%, 4 W Resistor110000-222
R214.7kQ, +5%, 4 W Resistor110000-472
R2210 kQ, +5%, % W Resistor110000-103,
R2320k, +5%, % W Resistor110000-203,
R24-R273300, +5%, % W Resistor110000-331
R282.2kQ, +5%, 4 W Resistor110000-222
R294.7kQ, +5%, %& W Resistor110000-472
R3010kQ, +5%, % W Resistor110000-103,
R3120kQ, +5%, % W Resistor110000-203,
R32-R35330, +5%, % W Resistor110000-331
R362.2kQ, +5%, 4 W Resistor110000-222
R374.7kQ, +5%, 4 W Resistor110000-472
R3810kQ, +5%, 4 W Resistor110000-103,
R3920kQ, +5%, % W Resistor110000-203
R40-R45680, +5%, % W Resistor110000-680
R46-R485109, +5%, %& W Resistor110000-511
R49-R6210kQ, +5%, % W Resistor110000-103,
R63-R703.3kQ, +5%, 4 W Resistor110000-332

4.19

Page 44

Illustrated Parts Lists System I

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
R71, R7210kQ, +5%, 4 W Resistor110000-103,
R73-R801000, +5%, 4 W Resistor110000-101
R81-R851kQ, +5%, % W Resistor110000-102
R86-R904700, +5%, % W Resistor110000-471
R91-R941kQ, +5%, % W Resistor110000-102
R951500, +5%, 4 W Resistor110000-151
R962200, +5%, % W Resistor110000-221
ROT1500, +5%, % W Resistor110000-151
R9B4.7kQ, +5%, 4 W Resistor110000-472
R991kQ, +5%, % W Resistor110000-102
R100220, 45%, 4 W Resistor110000-221
RIOL4.7kQ, +5%, 4 W Resistor110000-472
R1021kQ, +5%, % W Resistor110000-102
R1034700, +5%, % W Resistor110000-471
R1041kQ, +5%, 4 W Resistor110000-102
R105,4700, +5%, % W Resistor110000-471
R1061kQ, +5%, % W Resistor110000-102
R1074700, +5%, % W Resistor110000-471
R1081kQ, +5%, 4 W Resistor110000-102
R1094700, +5%, % W Resistor110000-471
R110, R1112200, +5%, 4% W Resistor110000-221
R1121kQ, 45%, % W Resistor110000-102
R1133902, +5%, % W Resistor110000-391
R114, R115,10kQ, +5%, 4 W Resistor110000-103,
R1164.7kQ, +5%, % W Resistor110000-472
R1715kQ, +5%, % W Resistor110000-153
R11822 kQ, +5%, % W Resistor110000-223
RIO1kQ, +5%, % W Resistor110000-102
R120, R12110kQ, +5%, 4 W Resistor110000-103
R1221kQ, +5%, % W Resistor110000-102
R12322kQ, +5%, % W Resistor110000-223,
R12415kQ, +5%, 4 W Resistor110000-153,
R125,10kQ, +5%, 4 W Resistor110000-103,
R12639kQ, +5%, % W Resistor110000-393
R127, R12827kQ, +5%, % W Resistor110000-273,
R12939kQ, +5%, % W Resistor110000-393,
R13010kQ, +5%, % W Resistor110000-103,
R13115 kQ, +5%, % W Resistor110000-153,
R132, R13310kQ, +5%, % W Resistor110000-103,
R1341kQ, +5%, 4 W Resistor110000-102
R1353900, +5%, 4 W Resistor110000-391
R1365609, +5%, 4 W Resistor110000-561
R137, R138.1kQ, +5%, % W Resistor110000-102
R139, R14010 kQ, +5%, 4 W Resistor110000-103,

4-20

Page 45

system I Illustrated Parts Lists

LSI Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
R1414.7kQ, +5%, % W Resistor110000-472
R1421kQ, +5%, % W Resistor110000-102
R143, R1444.7kQ, +5%, 4 W Resistor110000-472
R14510kQ, +5%, % W Resistor110000-103
R1461kQ, +5%, % W Resistor110000-102
R1474,.7kQ, +5%, 4 W Resistor110000-472
R1481kQ, +5%, % W Resistor110000-102
R1492209, Resistor, 2WQ, +5%,110001-221
R150, R1514.7kQ, +5%, 4 W Resistor110000-472
R152-R1671kQ, +5%, % W Resistor110000-102
R1682209, +5%, % W Resistor110000-221
R169, R1704.7kQ, +5%, 4 W Resistor110000-472
R171, R172479, +5%, 4 W Resistor110000-470
R1732200, +5%, % W Resistor110000-221
R174, R175,3300, +5%, % W Resistor110000-331
R1761kQ, +5%, % W Resistor110000-102

Sockets

1c40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
YK40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
23B28-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C28
S/G/IK.40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
Sy/K40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
9E40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
10)28-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C28
ly28-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C28
12H64-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C64
13E24-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C24
16)/K40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40
17F16-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C16
17H24-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42.C24
17K40-Pin, Medium-Insertion-Force, Integrated Circuit Socket79-42C40

Miscellaneous

Q9, Q10Nylon Snap-In Fastener81-4302
Yl14.381 MHZ Crystal90-101

Test Point (Acceptable substitute is part no. 020670-01) 179051-002

4-21

Page 46

Illustrated Parts Lists

4-22 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden wihout tne specific witlen permission of Alan Games Corporation, Miptas, CA. This drawing only conditionally issued, and neither receipt nor possession my ight nor Kens io use the subject mato the drawing SP ery Goals or tochnicatineriebon shown feteon, Nor any agro Two i Having oF ary part hated! Pop for manufacture oy ‘vendors of Atari Games Corporation, and for manufacture under the corporation's written license, no right is granted to reproduce this drawing ‘or the subject mater thereot, unless by written agreement with or written permission from the corporation.

TABLE A

OPTIONS CUSED/NOT USED)

vers | -04 02 -03 orstc

RiY¥
ci7Y¥

cis y |_¥

ci7-ANN

| Ci18-A N N

‘SHLYY
Q3Yeye
Q3 HEATSINK|YN
RitNN

Ris N N

© SEE P/L FOR VALUE

Figure 4-6 Audio II PCB Assembly A043661-02 B System I

Page 47

System I Mlustrated Parts Lists

Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

C1-C53300 pF, 25 V Radial Electrolytic Capacitor123003-338
C6-C12-1 wE, 50 V Ceramic Capacitor122002-104
C13-C1422 wE 35 V Electrolytic Capacitor24-350226
C15-C18.22 wR, 25 V Ceramic Capacitor122006-224
€19-C20.001 wF, 50 V Ceramic Capacitor122002-102
C21-C23-1 4K 50 V Ceramic Capacitor122002-104

Diodes

CR1-CR4Type-1N5401 Diode31-1N5401
CR5-CR10Type-1N4001 Diode31-1N4001
CRI13Type-1N4002 Diode31-1N4002

Connectors

JACDCKey 6, 9 Ckt., .156-Inch Ctr. Header Connector179213-009
JAUXKey 6, 9 Ckt., .156-Inch Ctr, Header Connector179213-009
JCDL2 Ckt., .156-Inch Ctr. Header Connector179213-002
JSPKKey 3, 6 Ckt., .156-Inch Cur. Header Connector179213-006

Integrated Circuits

Q1-Q2Type-TDA-2030 Amplifier137301-001
Q3Standup Type-7815Integrated Circuit37-7815

Resistors

RI10 k®, Dual Horizontal Pot Resistor119011-103
R3100, +5%, % W Resistor110000-100
R4-R722 kQ, +5%, % W Resistor110000-223
R8-R910kQ, +5%, 4 W Resistor110000-103
RIO-Ri11kQ, +5%, % W Resistor110000-102
R12-R1310, +5%, % W Resistor110000-010
R14OQ, +5%, % W Resistor110005-001

Miscellaneous

swSPDT Miniature Slide Self-Test Switch69-004

Type-TDA-2030 Heat Sink 178190-032 #6-32 x 3/8-Inch Cross-Recessed Pan-Head Screw 72-1606 #6-32 Nut/Washer Assembly 75-9516

Thermal Compound 78-16001 Hot Melt Adhesive 106006-001 Test Point 179051-001

4-23

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation, ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).

  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode.

CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

Glossary

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. Dc Direct current, meaning current flowing in one direction and of a fixed value, DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is nialfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.

Page 50

GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached toa piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. vO Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated. by external logic. This signal tells the microprocessor that external logic needs attention, Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode.

LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known, voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE Ina raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR: A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (eg., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault.

VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY ‘A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage. a

Page 51

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players.(in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor,

Page 52

ATARI GAMES CORPORATION 675 SYCAMORE DRIVE P.O. BOX 361110 MILPITAS, CALIFORNIA 95035 (408) 434-3950 © TELEX 5101007850