Kangaroo TM-204 3rd Printing
Kangaroo (Sun Electronics, 1982) · Technical Manual · 64 pages · 50 sections · original scan

This page is a drawing, shown as the original scan.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on a label on the outside back of the e@
game. The same number is also on the chassis of the video display, power supply, Regulator/Audio II Printed Circuit Board (PCB), and the Central Processing Unit (CPU) and Video PCBs. Please mention this number when calling your distributor for service.
GAME SERIAL NUMBER IDENTIFICATION TAG
DISPLAY
CENTRAL PROCESSING UNIT (CPU) PCB
VIDEO PCB
REGULATOR AUDIO li PCB
POWER SUPPLY
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Manufactured under license from Sun Electronics Corporation
Kangaroo™
© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
The Kangaroo™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles,
In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game
Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035
Lithographed in the USA. 6L
Kangaroo™
INTCRFER EL to licensed communications services is not permitted by the FCC (Federal Communications Commission) \f you suspect interference from an ATARI game at your location, check the following: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The game’s power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact:
ATARI Customer Service (800) 526-3849 or (800) 538-1611
Notice Regarding Non-ATARI Parts
Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
The warranty printed on the inside back cover of this manual may be voided, if you do any of the following:
®@ you substitute non-ATARI parts in your coin-operated game, or
@ you modify or alter any circuits in your ATARI game by using kits or parts not supplied by Atari.
Not only may the use of any non-ATARI parts void your warranty, but any such alteration may also adversely affect the safety of your game and may cause injury to you and your players.
Kangaroo™
Table of Contents
Set-Up Procedures A. New Features... 1-3 B. Game Inspection . 1-3 C. Game Installation........ 1-3
- Installation Requirements . 1-3
- Voltage Selection . 1-3 D. Switch Locations... 1-4
- On/Off Switch ... 1-4
- Utility Panel Switches 1-4
- Service Switch. . 1-4
- Option Switches .. 1-4 E. Option Switch Settings . 15 F. Self-Test Procedure . . 16 G. GamePlay .... 1-8
- Attract Mode .... 1-8
- Ready-to-Play Mode . 18
- PlayMode ....... 1-9
- High Score Mode . 1-10
- Hints for Game Play ... 0.0... cece cece eee eee ete 1-10
Troubleshooting A. Comments on Troubleshooting.... 0.2... 0.0.00 c eee eee ee eee 22 B. Self-Test Procedure ........... .. 22 C. Glossary of Schematic Signal Descriptions ...................0005 2-4
Maintenance, Repair and Parts A. Cabinet-Mounted Assemblies... ........ 60s cece cece cence eee 3-2 B. The Control Panel ........-. .. 37 C. Fluorescent Tube and Speaker 3-12 D. Video Display . . 3-14 E CoinDoor......... 3-18 F. Printed-Circuit Boards . . .. 321 G. Power Supply Assembly . 2.0.0.2... 00. c cece eee eee teen 3-30
Figure 1-1 Figure 1-2 Figure 1-3 Figure 2-1
Figure 2-2 Figure 2-3
Figure 3-1
Figure 3-2 Figure 3-3 Figure 3-4
Figure 3-5
Figure 3-6 Figure 3-7 Figure 3-8
Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12
Table 1-1 Table 1-2 Kangaroo™
List of Illustrations
Game Overview, Upright Cabinet 1-2 Game Switch Locations .. > . 14 Self-Test Procedure ........ - 16 Self-Test Screen 1—Test Passes... ........... 0.0 c ec ee eee eee 2-2
Self-Test Screen 1—Test Fails. ........ 0.0... e cece eee eee eee 2:3 Self-Test Screen 2 2.2... 6. ccc cece cence eee eens 2-3
Maintenance, Repair and Parts: Cabinet-Mounted Assemblies, Upright Cabinet.................. 3-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . . . The Control Panel Control Panel Assembly .. 8-Position Joystick Assembly
Fluorescent Tube and Speaker, Upright Cabinet ................. 3-12 Fluorescent Tube and Speaker, Ireland-Built Cabinet Video Display... . Vertically Mounted Coin Door... . 3-18 Printed-Circuit Board (PCB) Removal ................2 0 cece ee 3-21
Kangaroo Central Processing Unit PCB Assembly ............... 3-22 Kangaroo Video PCB Assembly ............. . 3-26 Regulator/Audio || PCB Assembly . 3-28 Power Supply Assembly ......... 0... c cece eee eee eae 3-30
List of Tables
Option Switch Settings ......- 0.0... cece ccc eee ee 1-5 Kangaroo SCOrINg «6... eee eee eee eee teen ene 1:10
Kangaroo™
If reading through this manua! does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.
WEST and CENTRAL U.S.A. Parts and Service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday—Friday, 7:30-4:00 pm Facific Time) s From California, Alaska, or Hawaii (408) 745-2900 Po Service from anywhere in the area shown in white toll-free (800) 538-1611
EAST U.S.A. Service only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Dtive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) age From New Jersey > (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849
EUROPE Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND @ 06252155
Set-Up Procedures
How to Use This Manual
This manual, written for game operators and service technicians, describes the Kangaroo™ game.
The manual contains information about al/ Kangaroo cabinets. Whenever information is unique
to the Upright cabinet, this symbol appears: i Built cabinet, this symbol appears: rl
Whenever information is unique to the Ireland-
Chapter One details new features, game set-up, option switch settings, self-test procedures, and game play.
Chapter Two includes troubleshooting procedures.
Chapter Three contains maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.
Chapter
Set-Up Procedures Kangaroo™
FLUORESCENT TUBE AND SPEAKER See Figure 35
COLOR VIDEO DISPLAY
Rhye See Figure 36
&POSITION JOYSTICK See Figure 3-4 ACCESS PANEL
CONTROL PANEL See Figures 3-2 & 3-3
CENTRAL PROCESSING UNIT (CPU) PCB See Figures 3-8 & 3-9 VIDEO PCB See Figures 3-8 & 3-10
COIN DOOR - See Figure 3-7 SERVICE SWITCH
REGULATOR/ AUDIO II PCB UTILITY PANEL See Figures 3-8 & 3-11
See Figure 1-2
POWER SUPPLY See Figure 3-12
SHOCK HAZARD Connect this game only to a grounded i x . POWER ONIOFF SWITCH 3-wire outlet. If you have only a 2-wire out: Goo Fisuie 1. let, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!
Figure 1-1 Game Overview
1-2
Kangaroo™
A. New Features
The Kangaroo™ game has two new features. Even if you are familiar with ATARI® games, you should
B. Game Inspection
Please inspect your game carefully to insure that it was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the PCBs are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the power cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. Set-Up Procedures
@ Note the game’s serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Kangaroo game PCBs, Regulator/Audio 1) PCB, power supply and video display. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check major subassemblies, such as the power supply, control panel and video dis- Play, for secure mounting.
C. Game Installation
- Installation Requirements
Power 150W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 64 x 79 cm (25% x 31 in.) 174 cm (68% in.) Ireland-Built Cabinet Space Required 64 x79 cm (25%, x 31 in.) Game Height 174 cm (68% in.) Space Required Game Height
- Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three different voltage selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).
Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for your location's line voltage (see Figure 3-12).
Set-Up Procedures
D. Switch Locations
- On/Off Switch The on/off switch is located on the back of the cabinet, lower left side (see Figure 1-2).
- Utility Panel Switches The utility panel includes the volume control, selftest, coin switch, and coin counter(s). The coin switch is used to credit the game and it activates the left coin counter. These switches are located inside the upper coin door (see Figure 1-2). Kangaroo™
- Service Switch The service switch is located on the CPU PCB. It is used to credit the game without activating the coin counter. It can also start self-test if it is pressed while powering on the game.
- Option Switches Option switches are located on the CPU PCB in the upper right corner, to the right of IC42.
UTILITY PANEL:
COIN COUNTER
SELF-TEST
VOLUME CONTROL COIN (TO increase, turn clockwise) GAME OPTION SWITCHES
POWER ON/OFF SWITCH
Figure 1-2 Game Switch Locations
Kangaroo™ Set-Up Procedures
E. Option Switch Settings
Table 1-1 details game option switch settings. Op- To verify option switch settings, power the game tions are preset at the factory and shown by the off and then on again. Set the self-test switch to on symbols. However, you may change the settings to and verify the settings on the self-test screen. Then suit your individual needs. set the self-test switch to off.
Table 1-1 Option Switch Settings The table below contains the switch settings for options re- The coin mechanism(s) is a device on the inside of the coin door lating to number of Kangaroo lives, game difficulty, bonus and that inspects the coin to determine if the correct coin has been inprice options. The switches are on the CPU PCB to the right of serted. After this inspection, the mechanism either accepts the C42 and are accessible when the PCB is mounted in place. coin or rejects it.
Settings of 8-Toggle Switch on Kangaroo CPU PCB
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Option |
Off 3 Kangaroo Lives << On 5 Kangaroo Lives Off Easy game difficulty On Hard game difficulty
| Off | Off | No Bonus Kangaroos |
| On | Off | Bonus Kangaroo at 10,000 |
| Off | On | Bonus Kangaroo at 10,000, 30,000 and every 30,000 thereafter |
| On | On | Bonus Kangaroo at 20,000, 40,000 and every 40,000 thereafter |
Left Coin Mechanism Right Coin Mechanism Games with one coin counter Games with two coin counters
| Off | Off | Off | Off | 1 coin for 1 credit | 1 coin for 1 credit | < |
| On | Off | Off | Off | 2 coins for 1 credit | 2 coins for 1 credit | |
| Off | On | Off | Off | 2 coins for 1 credit | 1 coin for 3 credits | |
| On | On | Off | Off | 1 coin for 1 credit | 1 coin for 2 credits | |
| Off | Off | On | Off | 1 coin for 1 credit | 1 coin for 3 credits | |
| On | Off | On | Off | 1 coin for 1 credit | 1 coin for 4 credits | |
| Off | On | On | Off | 1 coin for 1 credit | 1 coin for 5 credits | |
| On | On | On | Off | 1 coin for 1 credit | 1 coin for 6 credits | |
| Off | Off | Off | On | 1 coin for 2 credits | 1 coin for 2 credits | |
| On | Off | Off | On | 1 coin for 2 credits | 1 coin for 4 credits | |
| Otf | On | Off | On | 1 coin for 2 credits | 1 coin for 5 credits | |
| On | On | Off | On | 1 coin for 2 credits | 1 coin for 10 credits | |
| Off | Off | On | On | 1 coin for 2 credits | 1 coin for 11 credits | |
| On | Otf | On | On | 1 coin for 2 credits | 1 coin for 12 credits | |
| Off | On | On | On | 1 coin for 2 credits | 1 coin for 6 credits | |
| On | On | On | On | Free play | Free play |
“4 Manufacturer's recommended settings
When bonus life options are changed, make sure the proper sticker behind the shield is displayed.
Set-Up Procedures
F. Self-Test Procedure
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary.
We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure.
Figure 1-3 Instruction Kangaroo™
Refer to Figure 1-2 for the location of the self-test switch and option switches. To perform the self-test, set the self-test switch to on or simultaneously power the game on and press the service switch. To end the self-test, set the self-test switch to off.
The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. \f a part of the test described in Figure 1-3 fails, refer to Chapter 2.
Self-Test Procedure
Test Passes
1, Set the self-test switch to on (see Figure 1-2).
- Observe the seven colored squares.
- Activate all switches: control panel, coin and service.
- Simultaneously press Player 1 and Player 2 start switches. The screen shows the self-test display. The ROMs and RAMs. are tested. If the screen is different from the self-test display, refer to Chapter 2, Self-Test Procedure.
Colors are blue, green, light blue, red, violet, yellow and white. If colors are not as described, refer to the raster-scan video display manual.
The 0 changes to 7 as the switch is activated. If test fails, refer to Chapter 3, The Control Panel. Push the joystick diagonally up and to the left. For proper game operation, both the top and left switches must close at the same time, and the top and left Os should each become 7. Push the joystick diagonally up and to the right, repeating the same procedure. Both the top and right switches should close, changing the corresponding Os to 1s on the screen. If the test fails, refer to Chapter 3, 8-Position Joystick Assembly.
Game sounds are produced and increment automatically from SOUND 1 through SOUND J. If test fails, refer to Chapter 2, Self-Test Procedure.
Game sounds: SOUND 1 SOUND 2 SOUND 3 SOUND 4 SOUND 5 SOUND 6 SOUND 7 SOUND & SOUND 9 SOUND A SOUND B SOUND C SOUND D SOUND E SOUND F SOUND G SOUND H SOUND ! SOUND J Game melody Kangaroo jumping Kangaroo punching Kangaroo falling Kangaroo dying Apple falling Kangaroo punching apple or gorilla Bonus Kangaroo awarded Begin new level Monkey dying Kangaroo getting fruit End of level Bell ringing Monkey column decreasing by one monkey Gorilla taking Kangaroo’s gioves Kangaroo crouching Apples falling from broken branch Kangaroo climbing ladder Kangaroo hopping
Kangaroo™ Set-Up Procedures
COCKTAIL ONLY PLAYER-2 JOYSTICK CONTROL LT. BLUE
COCKTAIL ONLY RED
PLAYER-2 PUNCH
VIOLET
GREEN 00: 0 YELLOW BLUE 0
WHITE
COLOR ADJUSTMENT ———_______ | CHART
EDGE CONNECTOR SETTINGS* a i DIP 12345678 3A 3B 4A: OPTION SWITCHES —————" ——_ oO c=] {2 e o f=] o Oo ro xo > e
SERVICE SWITCH —————>- S 0 RIGHT COIN MECH
1 vert con MECH +PLAYER stakt ———> 1 0
2PLAYER START
SOUNDS
GAME PRICING/ NO. OF LIVES
GAME DIFFICUTLY CREDITS
JOYSTICK CONTROL BONUS LIVES PUNCH
- These represent harness connections on the CPU PCB. 1 means the pin is shorted to ground in the harness. 0 means there is no connection in the harness.
Screen Pin on CPU
Shows Harness Connector 3A Cc 3B 3 4A Do 8A J
Figure 1-3 Self-Test Procedure, continued Self-Test Display
Set-Up Procedures
G. Game Play
The Kangaroo™ game is a one- or two-player game with a color raster-scan video display. Game action takes place in the branches of a tree. The player controls a mother Kangaroo who must hop and leap from the bottom of the screen to the top to rescue her kidnapped baby. In her effort to get to her baby, the Kangaroo must punch out monkeys and avoid fruit that is thrown or dropped by the monkeys.
Kangaroo has five possible modes of operation: attract, ready-to-play, play, high-score and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (all credits will be cancelled and the high score table will be erased).
- Attract Mode
The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode is continuous and stops only when a credit is entered, or when in self-test. In the attract mode, the screen displays one of three possible pictures.
The first picture shows ways to score points during game play. A mother Kangaroo hops across a top branch of the tree. She leaps to touch hanging fruit with her head and to ring a bell. When she touches the fruit, it disappears and a point value appears in its place. When she rings the bell, a new fruit appears where the old fruit was hanging. A monkey pursues the mother Kangaroo and she punches him. The monkey disappears, and a point value appears in his place. Meanwhile, the baby Kangaroo climbs down a ladder and goes to the mother Kangaroo. When they touch, the word MOM appears on the screen above the baby.
In addition to the game play simulation, PLAYER-1, LEVEL=1, PLAYER-2 and KANGAROO appear at the top of the screen. The high score appears in the center of the screen. Credits and © 1982 ATARI, INC. appear at the bottom of the screen.
1-8 Kangaroo™
The second picture shows the high-score table. The top ten scores and their matching initials appear on the screen. The words KANGAROO and IN- SERT COINS also appear.
The third picture simulates game play. Mother Kangaroo enters at the bottom of the screen. She hops across a tree branch and avoids fruit thrown or dropped by monkeys and punches out monkeys. She leaps to touch fruit with her head. She climbs a ladder to get to the next branch of the tree. In this way she hops, leaps and climbs to the top of the tree to rescue her baby. She rescues her baby, or in another simulated game, is destroyed by an apple thrown by a monkey.
In addition to game play, PLAYER-1, LEVEL =1, PLAYER-2, number of Kangaroo lives and bonus information appear at the top of the screen. The attract mode ends when coins are entered and accepted for game play.
- Ready-To-Play Mode
During this mode the game level and score(s) for one or both players appear at the top of the screen. The words PUSH ONLY 1 PLAYER BUTTON appear when 1 credit is inserted. The words PUSH 1 OR 2 PLAYERS BUTTON appear when 2 or more credits are inserted. LET’S CHALLENGE also appears in the center of the screen. Credits appear in the bottom left corner of the screen. This mode ends when a player pushes the start button.
A picture appears briefly on the screen, showing three mother Kangaroos on three branches of the tree. The mother Kangaroo on the top branch falls through a gap to the bottom of the screen. The other Kangaroos join their babies, and the words MOM appear above their heads.
Kangaroo™
- Play Mode
In the Play Mode, the player controls the mother Kangaroo with an 8-position joystick. Thus, the player causes the Kangaroo to hop to the right or left, or to leap up to touch fruit, or to jump over apples thrown at her by monkeys. She may climb up ladders, or SUPER-LEAP diagonally to the left or right to climb up log-type stairs. The Kangaroo may also duck to avoid thrown apples, or hop down diagonally to the left or right to get down the log-type stairs.
Another player control is the PUNCH button. When pushed, it causes the Kangaroo to punch with her boxing glove. She may punch monkeys for 200 to 400 points. She may also punch fruit that is thrown or dropped by monkeys for 100 to 200 points. In addition, Big Ape may appear and try to take the Kangaroo’s gloves. Punching Big Ape is worth 800 points.
Game play progresses by levels. Each level has four rounds. Game play begins at Level 1. Bonus points appear at the top left of the screen. There are 2,000 bonus points at the beginning of each round, and the points decrease by 100 every five seconds. Remaining bonus points are awarded at the end of the round.
In Level 1, Round 1, mother Kangaroo is at the bottom of the screen on the branch of a tree. She must get to the top of the screen to rescue her kidnapped baby by hopping across tree branches and climbing up ladders to get to the next branch. The Kangaroo must avoid apples thrown or apple cores dropped by monkeys. She must punch out the monkeys that are in her way. For extra points, she touches strawberries by leaping to touch them with her head or by hopping on them. (If the Kangaroo tings the bell, new fruit appears in place of the strawberries.) ‘Set-Up Procedures
The Kangaroo may also punch thrown or falling fruit for extra points. But if she is hit by fruit or touched by a monkey, she dies and a halo appears over her head. If she hops, leaps and climbs to the top of the tree and gets to her baby, this round ends.
In Round 2 there are log stairs instead of ladders for the mother Kangaroo to climb. To get up the stairs, she must leap diagonally (GSUPER-LEAP). The Kangaroo must be careful not to fall through any gaps in the stairs or on the branches, or she will die. Also, Big Ape may appear in this round. He takes the Kangaroo’s glove away from her by coming close to her and extending his arm. For about 10 seconds, the Kangaroo has to defend herself with a white flag. Then her glove reappears.
in Round 3 the baby Kangaroo is in a cage at the top of a column of monkeys. Mother Kangaroo may either punch out the monkeys one by one (for 400 points each), or climb up ladders to a branch of the tree where she can hop into the cage. The column increases by one monkey every 10 seconds. In addition, monkeys climb up a vine to get toa stack of 11 apples on a branch at the top of the screen. If the mother Kangaroo takes too long to get to her baby and a monkey gets to the apples, the branch breaks, and all the apples fal\ at one time.
In Round 4 there are ladders with missing rungs, stairs to climb, and gaps in the branches, making the rescue more difficult. If a player completes this round, Level 2, Round 1 begins. The player may punch the thrown fruit to score points. Play becomes more difficult as garne play progresses. The game ends when all the Kangaroo’s lives are used up.
1-9
Set-Up Procedures
- High-Score Mode This mode begins when a player has one of the top ten scores. Letters of the alphabet are at the top of the screen, and the high score table is below the letters. A player enters his initials by using the joystick to guide a highlighted square to his initials. By pressing the PUNCH button, the initial is transferred onto a line between the alphabet and the high-score table. After the initials are entered, they are transferred into the table. To reset the high-score table, power the game off and then on, or enter and end the self-test mode.
- Hints for Game Play
@ Ring the bell for extra points. New fruit with higher point value will appear in place of the old fruit. @ Avoid walking into a monkey. Punch monkeys for 200-400 points each. @ Do not let Big Ape take mother Kangaroo’s glove (it reappears after 10 seconds). @ Mother Kangaroo must duck, leap or punch to avoid being killed by thrown or dropped fruit.
+10 Kangaroo™
Table 1-2 Kangaroo Scoring
Kangaroo Punching Points Thrown Apples 100 Monkey 200 Apple Cores 200 Monkey from Column 400 Big Ape 800
Kangaroo Jumping to Touch Fruit Points Strawberry 100 Tomato Cherries Pineapple Completing Round
- Decreases by 100 every 5 seconds
Troubleshooting
This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or isn’t working properly. The expanded self-test procedures in this chapter are included to help the qualified electronic technician determine why the game isn’t working properly.
Chapter
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio || PCB, or the video display?
The next step is to check all harness wires and connectors to the suspected failing assembly. !f you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.
When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair are relatively simple, as these assemblies are not too complicated. If a game PCB is failing, troubleshooting and repair will greatly depend on your understanding of the operation of the PCB.
To effectively troubleshoot problems of a game PCB, it is necessary for you, the technician, to become familiar with the PCB’s hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Kangaroo™
B. Self-Test Procedure
To enter Self-Test, set the self-test switch to the on position. The screen displays the picture below. See Chapter 1, Section F, Self-Test Procedure for a complete description of this picture.
DIP 12345578 3A 3B 4A ooorc000 td OO kb
0 0 SOUND
Figure 2-1 Self-Test Screen 1 Test Passes
Kangaroo™
OIP 12345678 3A 3B dA BH Ooo10000 4 O Ld f
Figure 2-2 Self-Test Screen 1 Test Fails
SCREEN 1: ROM FAILURE is indicated on the screen by the words ERROR ROM- and a number (for a ROM failure on the CPU PCB), or the words ERROR ROM V- and a number (for a failure on the Video PCB).
Bad ROM Chip Location CPU PCB Screen Display ROM-0* Ic7 ROM-1 1C8 ROM-2 Ico ROM-3 Ic10 ROM-4 IC16 ROM-5* IC17 ROM-8* 1C24 ROM-12* 1028 Video PCB ROM V-0 IC76 ROM V-1 1052 ROM V-2 1077 ROM V-3 1C53
*Does not display on the screen if defective.
RAM FAILURE is indicated by a blank screen or by garbage displayed on the screen for a defective RAM at IC5 or IC6 on the CPU PCB. Make sure that ROM-0 and ROM-5 are good on the CPU PCB. In addition, inspect the dynamic RAM on the Video PCB Troubleshooting
at locations 1C55-62, 66-73, 79-86 or 93-100. Troubleshoot using the game schematics and the CAT Box (using a 280 interface) or 8 bus Controter to locate the failing RAM.
SWITCH FAILURE is indicated by the proper 0 or 7 not changing on the screen when the switch is activated. Troubleshoot using the information in Chapter 3, Section B and game schematics.
SOUND FAILURE is indicated by no sound. Check the volume control levels on the utility panel and on the CPU PCB at VR2. Troubleshoot the following sound circuitry on the CPU PCB: G.I. sound chip at IC50, ROM 8 at 1C24, Z80 Microprocessor at 1C34, RAMs at IC32 or 33, or audio amplifier at IC61.
To go to screen 2, push the 1-player start and either PUNCH switch at the same time.
SCREEN 2:
A white crosshatch pattern with white dots centered in each square appears on the screen (see Figure 2-3). The center part of each side of the red rectangle should be %-inch behind the bezel, out of view. Use this pattern for convergence and white balance (see the raster-scan video display manual).
Figure 2-3 Self-Test Screen 2
Troubleshooting Kangaroo™
C. Glossary of Schematic Signal Descriptions
CPU PCB Signals
NMI
WAIT
INT
o
cs2
RDG)
RD(H)
WRI WR(H)
x X¥(H) | VPOS
HPOS
BSEL
VL EN PRI
INO
ini
iN2
iN3
ina
ouTo
ouTi
OuT2 Non-Maskable Interrupt
Wait
Interrupt Request (every 16 ms)
CPU Clock (2.5MHz)
Address Select (E8XX-EBXX)
Start Address of Data in Picture ROM for DMA Low Byte
High Byte
Start Address in Bit Map RAM (Where Picture is Written) During DMA Low Byte
High Byte
Picture Size for DMA and DMA Start Low Byte
High Byte
Vertical Start Address in Bit Map
Horizontal Start Address in Bit Map
Dynamic RAM Bank Select Latch Set
A and B Bit Map Control Latch Set
Input Address Select ECO0 (See Memory Map)
Input Address Select ED00 (See Memory Map)
Input Address Select EE00 (See Memory Map)
Input Address Select EF00 (See Memory Map)
Input Address Select E400 (See Memory Map)
Output Address Select ECOO (See Memory Map)
Output Address Select EDO0O (See Memory Map)
Output Address Select EEOO (Not Used) OUT3
HFEN
SDO0-SD7
BDIR
BC1
1S0-1S3
0S0-0S3 Output Address Select EFOO (See Memory Map)
Set Color-Shading Latch
Sound Microprocessor Data Bus
GI AY-3-8910 Sound Chip Input/Output Select
Gl AY-3-8910 Sound Chip Addres/Data Latch Select
MB8841 Custom Microcomputer Input Data Bus
MB8841 Custom Microcomputer Output Data Bus
Video PCB Signals KO
Kt
K2
KIS1
Kost
XG
LDISFT
WE
EXCT
EXCT
SEL Wil (A)
SEL Wii (B)
¢sco00
BSELO
BSEL 2
Ave’ Dynamic RAM Timing Signals (See Timing Diagram in Kangaroo Schematic Package)
DMA in Progress (Active High)
DMA in Progress (Active Low)
Flip Video Address (Dynamic RAM A)
Flip Video Address (Dynamic RAM B)
Character ROM Address Select
Bank Select Dynamic RAM A
Bank Select Dynamic RAM B
Horizontal Blanking (Active Low)
Kangaroo™ Troubleshooting
TRGA
VSYNC
ARASO
ARAS1
ACASO
ACAS1
AWEO
AWE1
BRASO
BRAS1 Horizontal Syne
Vertical Sync
Dynamic RAM A* Color Shading/Red RAS
Dynamic RAM A Blue/Green RAS.
Dynamic RAM A Color Shading/Red CAS
Dynamic RAM A Blue/Green CAS.
Dynamic RAM A Color Shading/Red Write Enable
Dynamic RAM A Blue/Green Write Enable
Dynamic RAM B Color Shading/Red RAS
Dynamic RAM B Blue/Green RAS
- NOTE: Dynamic RAM A refers to Playfield Bit Map; Dynamic RAM B refers to Motion Object Bit Map BCAS1
BWEO
BWE1
ANAX0-13
AVBX0-13
ABPO-11
ABXO0-13
DPZO-3
DPRO-3
DPGO-3
DPBO-3
DXZ0-3 Dynamic RAM B Color Shading/Red CAS
Dynamic RAM B Blue/Green CAS
Dynamic RAM B Color Shading/Red Write Enable
Dynamic RAM B Blue/Green Write Enable
Dynamic RAM A Video Address Dynamic RAM B Video Address
Picture ROM Address
Dynamic RAM Address from CPU and for DMA
DMA Color Shading Data from Picture ROM
DMA Red Data from Picture ROM
DMA Green Data from Picture ROM
DMA Blue Data from Picture ROM
Dynamic RAM Data Bus—Color Shading Data
Troubleshooting
DXRO-3
DXGO-3
DXBO-3
XXA0-6
XXB0-6
PRIA
PRIB
ENA
ENB Dynamic RAM Data Bus—Red Data
Dynamic RAM Data Bus—Green Data
Dynamic RAM Data Bus—Blue Data
Dynamic RAM A Address Bus
Dynamic RAM B Address Bus
Playfield Priority (Active Low)
Motion Object Priority (Active Low)
Playfield Video Output Enable (Active High)
Motion Object Video Output Enable (Active High)
Playfield Red Color Shading (Active Low)
Playfield Green Color Shading (Active Low)
Playfield Blue Color Shading (Active Low)
Motion Object Red Color Shading (Active Low)
Motion Object Green Color Shading (Active Low) BBHF
AR
AG
AB
AVR
AVG
AVB
BR
BG
BB
BVR
BVG
BVB Kangaroo™
Motion Object Blue Color Shading (Active Low)
Playfield Red Data
Playfield Green Data
Playfield Blue Data
Playfield Red Data AND Playfield Red Color Shading AND Playfield Priority
Playfield Green Data AND Playfield Green Color Shading AND Playfield Priority
Playfield Blue Data AND Playfield Blue Color Shading AND Playfield Priority
Motion Object Red Data
Motion Object Green Data
Motion Object Blue Data
Motion Object Red Data AND Motion Object Red Color Shading AND Motion Object Priority
Motion Object Green Data AND Motion Object Green Color Shading AND Motion Object Priority
Motion Object Blue Data AND Motion Object Blue Color Shading AND Motion Object Priority
Maintenance, Repair and Parts
This chapter details maintenance and repair information, and provides information for you to order parts for your Kangaroo game. Please note that common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598thru approximately 190000-.
When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Atari Customer Service numbers are listed in the front of this manual for your convenience.
Chapter
Maintenance, Repair and Parts Kangaroo™
A. Cabinet-Mounted Assemblies
Schematics, Self-Test Label & Manuals— see parts list on following page 03841101 binet A; (Cabinet Assy.) 037332-01
(Grille) Fluor. Light & Speaker— 178034-024 036498-01 See Figure 3-5 (TMolding) (Upper Retainer) 71-2110 (Lock) 038420-01 (Attract. Glass) 037419-02 (Access Panel)
(Lower Retainer)
Video Display— 036495-01
- KGalle) CPU PCB Assy.— See Figures 3-8 & 39 038419.01 78-6900402 nels (Tape) Video PCB Assy.— See Figures 38 & 3-10 178013-001 (Latch) Control Panel Assy.— See Figures 3-2 & 3-3 A038578-01 Reg./Audio Il PCB Assy.— (Main Harn. Assy.) See Figures 3-8 & 3-11
~ ‘A038004.01 Coin Door Assy.— (Util, Sw. Harn.) ‘See Figure 3-7 :
A038453-01 (Power Harn. Assy.)
A037491-01 Power Supply Assy.— (Coin Box) our , See Figure 312
038003-01 (Util. Panel)
A002465-01 (Coin Counter)
69-001 (Self-Test Sw.) 62-041 ‘Coin Sw.) 178048-001 A037470-01 A037453-03, (On/Off Sw. A037454-03 & (Casten , A037455-03 09282-01 (Power Cord) (On/Off Sw. Cover) ~~ 78-3201 19-9032 (Glide) (Vol. Control)
Figure 3-1 Cabinet-Mounted Assemblies Upright Cabinet A038410-01 A
Kangaroo™ Maintenance, Repair and Parts
Figure 3-1 Cabinet-Mounted Assemblies, continued Upright Cabinet Parts List
Part No. Description A002465-01 6V Coin Counter
| A037453-03 | Strain-Relief Power Cord | (U.S.) |
| A037454-03 | Strain-Relief Power Cord | (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, |
Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A037455-03 | Strain-Relief Power Cord | (Australia and New Zealand) |
A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Utility-Switch Panel Harness Assembly
| A038411-01 | Cabinet Assembly | includes legs and PCB retainers, but not the rear access panel) |
A038578-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-204 Kangaroo™ Schematic Package ST-204-01 Kangaroo Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display Substitute TM-201 when using part no. 92-055, Wells-Gardner 19-inch Display Substitute TM-205 when using part no. 139003-1005 or -1205, Sanyo 19-inch Display Substitute TM-197 when using part no. 139003-1004 or -1204, Matsushita 19-Inch Display TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPOT Self-Test Switch
| 71-2110 | Lock Mechanism | (for rear access panel) |
78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x \-Inch Thick (72 in. required) 003053-01 Lower Attraction Glass Retainer 009992-01 On/Off Switch Cover
| 034536-01 | Foam Vibration Damper | (for Kangaroo game PCBs) |
034536-02 Foam Vibration Damper (for Regulator/Audio 1! PCB) 036495-01 Speaker Grille 036498-01 Upper Attraction Glass Retainer 036686-01 Card of Game Pricing Labels (not shown in illustration)
| 037419-02 | Rear Access Panel | (does not include fock) |
| 037332-01 | Ventilation Grille | (located on cabinet top) |
038003-01 Utility Switch Panel for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038419-01 Video Display Shield with Graphics 038420-01 Attraction Glass with Graphics 178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 178070-001 Volume Control Knob
Maintenance, Repair and Parts Kangaroo™
Schematics, Self-Test Label & Manuals— see parts list on following page
03822601 (Grille) 178034-024 (FMolding) 037332.01 (Grille) Fluor. Light & Speaker— see Figure 3-5
038439-01 (Shield) , 03772102 Video Display— (Access Panel) see Figure 3-6 ; 2 & 7 4 71-2110 aN fiat &-Position : \ Joystick Assy.— See Figure 3-4 78-6900402 (Tape) 178013-001 (Latch) Contro! Panel Assy.— see Figures 3-2 & 3-3
CPU PCB Assy.— see Figures 3-8 & 3-9 A038004-01 (Util. Sw. Harn} Coin Door Assy.— see Figure 3-7 Video PCB Assy.— see Figures 38 & 3-10
Reg/Audio {| PCB Assy.— Figures 3-8 & 311 see Figures 3-8 & A038452.01 038003-01 (Main Harn. Assy.) (Util. Sw. Brkt.) A002465-01 (Coin Counter) 69-001 (Self-Test Sw.) 62-041 (Coin Sw.) 19-9032 (Vol. Ctrl.) A037491-01 (Coin Box) a 78-3201 (Glide) A038453-01 (Power Harn. Assy.)
A037454-03 (Power Cord) {/ aS Power Supply Assy.— 009992-01 see Figure 3-12 178048-001 On ort Sw. Cvr,) (Caster) 03747001 (OniOft Sw.)
Figure 3-1 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet A038430-01 B
Kangaroo™ Maintenance, Repair and Parts
Figure 3-1 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet Parts List
Part No. Description A002465-01 Coin Counter A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly
| A038431-01 | Cabinet Assembly | (includes glides and PCB retainers, but not the rear access panel) |
A038452-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-204 Kangaroo™ Schematic Package ST-204-01 Kangaroo Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (Substitute TM-201 when using part no. 92-055, 19-inch Wells Gardner Display) TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 OPODT Self-Test Switch
| 71-2110 | Lock Mechanism | (for rear access panel) |
78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, Y4-Inch Wide x }-Inch Thick 009992-01 On/Off Switch Cover 036686-01 Card of Game Pricing Labels (not shown in illustration)
| 037721-02 | Rear Access Panel | (does not include lock) |
| 037332-01 | Ventilation Grille | (located on cabinet top) |
038003-01 Utility Switch Bracket for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038226-01 Upper Cabinet Grille 038439-01 Video Display Shield with Graphics
| 038441-01 | Side Panel Decal | (not shown in illustration) |
178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Kangaroo™
B. The Control Panel
Ac— WARNING Prior to removing or repairing any switch on the control panel, unplug the game.
To Open the Control Panel:
- Open the coin door. Reach up through the opening and release the spring-draw latches. They are on the cabinet side walls at each end of the control panel.
- Lift up on the control panel at the top edge, and tilt it toward you. The contro! panel edge next to the display shield has foam tape applied to it. The tape cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.
Leaf Switch Repair: © Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner. © To replace a leaf switch, remove the screw with a Phillips-head screwdriver. ® To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design. Maintenance, Repair and Parts
© Reinstall the switch. Reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs ‘on the switch.
Start-Switch Replacement: These switches have a very iow failure rate. If a switch should ever be suspect, first test it using the directions that follow.
To Test Switch: @ Remove the wires from the suspected switch. @ Attach the leads of an ohmmeter to normally open and common contacts. @ Check contacts (push and release the switch button) for closed and open continuity. © If the contacts do not operate sharply or always remain closed or open, then replace the switch.
To Replace Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.
Figure 3-2 SWITCH CONTACTS. START 1
BROWN NORMALLY OPEN CONTACT
BLACK COMMON CONTACT
START 2
YELLOW =| L- NORMALLY OPEN = CONTACT LT ce =~COMMON CONTACT
The Control Panel
Maintenance, Repair and Parts Kangaroo™
! WARNING !
Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.
A038435-01 (Cont. Pni./Decal) 171021-001 038438-04 8-Position Joystick Assy.— (Decal) see Figure 3-4 038224-01 (Cont. Pri.) ry 78-6900402 (Tape) 62-041 (Start Sw.) 75-010S (Flat Washer)
75-040S (Split-Lock Washer)
7591s (Bezel) (Hex Nut)
178030-003, 75-9910NO (Pushbtn. Assy.) (Nut) 75-5112B (Carriage Bolt)
“uamess) eon (Cont PaneiDeca) 038418-04 (Decal)
038267-01 (Cont. Panel)
Figure 3-3 Control Panel Assembly Upright Cabinet A038414-01 A lreland-Built Cabinet A038434-01 A
3-8
Kangaroo™ Maintenance, Repair and Parts.
Figure 3-3 Control Panel Assembly, continued Parts List
Part No. Description Upright Cabinet A038415-01 Control Panel with Decal 038267-01 Coniro! Panel 038418-04 Control Panel Decal Ireland-Built Cabinet A038435-01 Control Panel with Decal 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, Y4-Inch Wide x }-Inch Thick (24 in. required) 038224-01 Control Panel 038438-04 Control Panel Decal For Upright and Ireland-Built Cabinets A038455-01 Control Panel Harness Assembly 62-041 SPDT Momentary Pushbutton Start Switch 75-010S #10 Flat Washer 75.040S #10 Split-Lock Washer 75-5112B #10-24 x %4-Inch Black Carriage Bolt 75-9118 #10-24 Hex Nut 75-9910NO #5,-11 Steel Stamped Nut 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (Leaf switch only is part no. 160012-001) 171021-001 8-Position Joystick Assembly 178030-003 Black Pushbutton Assembly
3-9
Maintenance, Repair and Parts
Prior to removing or repairing the joystick, unplug the game.
To Repair the Joystick:
- First remove the entire joystick assembly from the control panel (see Figure 3-3). Now locate the four screws in the plastic joystick frame and remove these screws.
- Next remove the retaining ring from the bottom of the shaft. The assembly will come apart.
- To replace the bellows, pry it up and out of the plastic frame. @ Reassemble in reverse order. @ Note that the inner raised ring on the bellows is longer on one side. This side goes on the top of the assembly (toward the control knob).
- To replace a leaf switch, you don't need to disassemble the joystick. @ Using your thumbs, pry apart the plastic flanges on the switch holder. With your index finger, lift the switch up So that it will clear the plastic tab located ‘on the outside end of the switch holder. © Slide the switch out of its holder. Replace the switch in reverse order. Adjust the switch for a narrow gap.
99-080031 (Bellows)
99-080032 ible in the order indi- Disassemi ind (Stee! Washer) cated. (Circled numbers match the numbered instructions.)
99-080030
(Spring) ee
I 99-080037 (Sw.Plate)
82-AL616 @ Kangaroo™
“aS
99-080028 oa oe 99-080026 a ween N
99-080036 (lop Plate)
99-080029 (Washer)
99-080025 (Switch)
99-080033 (Guard/Actuator)
(Sw. Actuator) (Screw) 73-3003 '=--3)+—$® “eing) Figure 3-4 8-Position Joysick Assembly 171021-001
3-10
Kangaroo™ Maintenance, Repair and Parts
To Adjust the Joystick: deh ie fi ai 4, Adjust each switch for narrow gap.
- Make sure that each feaf switch is firmly seated in its e ‘Push the joystick handle awa fram the switch for
holder. There is a smail gray piastic tab on the outside easier servicing. "
end of the switch holder. The black plastic part of each @ Use a pair of needlenose pliers or a switch adjustleaf switch must be in front.of this tab, ment tool to bend each double set of blades in to-
- Check that all four leaf switches can be activated by ward the center. Make the bend where the double set watching the switch blades as you move the joystick of blades comes out of the black plastic part of the handle up, down, left and right. switch.
- Test the four diagonal positions. In each diagonal posi- 5. Recheck the switch action. The switches must move intion, two leaf switches should close. Switches should dependently for right, left, up, down and diagonal mocontinue bending slightly after making contact. tion of the joystick.
LEFT: BLUE, BLACK JOYSTICK— TOP REAR VIEW
WHITEIBLACK, BLACK
DOWN: VIOLET, BLACK
RIGHT: GREY, BLACK
Figure 3-4 8-Position Joystick Assembly, continued Parts List
Part No. Description
73-3003 Retaining Ring 82-AL616 #6 x 1-Inch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 2.Inch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard/Actuator 99-080036 Top Plate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator 171021-001 Joystick Assembly
3-11
Maintenance, Repair and Parts Kangaroo™
C. Fluorescent Tube and Speaker
Upright Cabinet | To Replace Fluorescent Tube:
- At the top front of the game, remove the three screws that secure the upper attraction-panel retainer to the cabinet. Loosen the three screws that secure the lower retainer to the cabinet. Lift the attraction panel up and out of its lower retainer.
- Remove the cardboard locking tab at each end of the tube.
- Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the locking tabs.
- Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood board. If the tube is not grounded, it may not start.
To Replace Speaker:
- Remove the two Phillips-head screws that secure the light board to the cabinet. Slide the board out and unplug the 5-pin harness connector. Remove the board from the cabinet.
- Unplug the two plug-in connectors on the speaker. Remove the hardware that attaches the speaker to the board. Repiace the speaker, and reinstall in reverse order.
Disassemble in the order indicated. (Circled numbers match the numbered instructions.)
Figure 3-5 Fluorescent Tube and Speaker
Kangaroo™ Maintenance, Repair and Parts
037469-01 (Bracket) 148001-001 (Speaker)
179035-001 (Lampholder)
‘A037457-01 (Hamess) 79-561816P (Wire Nut)
70-304 (Tube) 142028-xxx 99.11003 (Transformer) (Starter) A037540-01 (Grd. Wire) 99-11009 (Socket) 99-1106
Figure 3-5 Fluorescent Tube and Speaker, continued Upright Cabinet Assembly A037417-01 and -02 G Parts List
Part No. Description
A037457-01 Fluorescent Tube and Speaker Harness A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15W Cool White Fluorescent Tube 79-561816P. Spring-Connector Wire Nut for 16- to 18-Gauge Wires
99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket 142028-001 60 Hz 118V Ballast Transformer (used on A037417-01 assembly) 142028-002 50 Hz 118V Ballast Transformer (used on A037417-02 assembly) 148001-001 6 x 9-Inch 4-Ohm 15W Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder
Maintenance, Repair and Parts
Ireland-Built Cabinet * To Remove the Tube and Speaker Board: 1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker’s 5-pin harness connector. Open the control panel (see Figure 3-2, The Control Panel). From the top front of the game, remove the five button-head screws that secure the upper cabinet grille to the cabinet. Lift the grille up and away from the cabinet. Be careful that the glass display shield doesn't fall forward. Lift the video display shield up and out of the cabinet. Slide the baffle board that is below the fluorescent tube out through the front of the cabinet. Kangaroo™
- Remove the screws that secure the tube and speaker board to the cabinet. Slide this board up and out of the cabinet.
To Replace Fluorescent Tube:
- Remove the Y-lead connectors at each end of the fluorescent tube.
- Slightly rotate the tube up or down, and carefully remove it from its clamps. Replace it with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the Y-lead connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the contro! panel and the rear access panel.
To Replace The Speaker:
- Unplug the two plug-in connectors on the back of the speaker,
- Remove the hardware that attaches the speaker to the board. Replace the speaker and reinstall the hardware and two plug-in connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.
Disassemble in the order indicated. (Circled numbers match the numbered instructions.)
Figure 3-5 \ 038226-01 (Grille)
038217-01 (Baffie Board)
038439.01 (Shield)
Fluorescent Tube and Speaker, continued
Kangaroo™ Maintenance, Repair and Parts
Disassemble in the order indica- 038151-01 ted. (Circled numbers match the (dmpr. Wire) numbered instructions.)
99-11012 (Clamp) 038219-03 ‘ (Light & Spkr. Bd.)
\ 99-11009 (Socket)
99-11003 (Starter)
142028-002 (Transformer)
(Connector)
(Speaker)
A038253-01 (Harness)
Figure 3-5 Fluorescent Tube and Speaker, continued Ireland-Built Cabinet Assembly A038228-01 A Parts List
Part No. Description
A038228-01 Fluorescent Tube and Speaker Assembly A038253-01 Light and Speaker Harness Assembly 70-303* 18-Inch, 1-Inch Diameter, 15W Cool White Fiuorescent Tube 99-11003 Fluorescent Lamp Starter
99-11009 Starter Socket 99-11012* 1% -Inch Fluorescent Tube Clamp 035835-01 12:Inch Y-Lead Connector 038151-01 Jumper Wire 038217-01 Baffle Board 038219-03 Light and Speaker Board 038226-01 Cabinet Grille 038439-01 Display Shield 142028-002 50 Hz 118V Ballast Transformer 148001-001 6x 9Inch 4-Ohm 15W Oval High-Fidelity Speaker
- Acceptable substitutes are part numbers 70-304 (tube) and 99-11011 (clamp). They must be used together.
3-15
Maintenance, Repair and Parts Kangaroo™
D. Video Display To Remove Video Display:
- Open the rear access panel. Unplug the three display
Disassemble in the order indicated. (Circled numbers match the numbered instructions.)
- 038226-01 (Grille)
ow (Shield) i 92.049 037443-01 03843901 (6) i (Video Display) ‘Ghield) (Bezel) : 037750-01 038232-01 @) “eracken (Bezel)
Figure 3-6 Video Display
3-16
Kangaroo™ Maintenance, Repair and Parts
Figure 3-6 Video Display, continued Parts List
Part No. Description
Upright Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display Acceptable substitutes are: 92-055, Wells-Gardner 19-Inch Display—use with TM-201 139003-1005 or -1205, Sanyo 19-Inch Display—use with TM-205 139003-1004 or -1204, Matsushita 19-Inch Display—use with TM-197 037443-01 Display Bezel 038419-01 Display Shield with Graphics
Ireland-Built Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display Acceptable substitute is part no. 92-055—use with TM-201 037750-01 Display Mounting Bracket 038439-01 Display Shield with Graphics 038226-01 Upper Cabinet Grille 038232-01 Display Bezel
Maintenance, Repair and Parts Kangaroo™
E. Coin Door
170000-001 99-15023 (Base Plate) 179047.001 L- (Lamp Base) } i \ |
an | 99-15040 ia se-1s026 | (Lever) 99-15056 (Coin intet) (Screw for Bezel)
(Com Inlet)
PART OF 99-15069
; 99-15054 99-15055 t - 99-15068 iS (Pivot for Lever} (Retng. Screw) ay (Lockout Coil) “en Yor 99-15069 (Lockt. Coil Spring)
99-5027 (Coin Ret. Box)
ae.
75.9145 (Hex Nut)
75-056 (Lock Wash.) 99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel) 99-15060 <a (Sw. Cover) 99-15029 (Bracket)
99-15042 (Switch)
7244148 (Screw)
Figure 3-7 Vertically Mounted Coin Door A037619-xx C
Kangaroo™
99-15073 (Upper Door),
99-15063 (Screw)
99-15067 (Lock Assy.)
A037491-01 (Coin Box)
A037542-01 (Harness—not shown)
A037619-01 — U.S. 25</25¢ Coin Door ‘A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door A037619-05 — British 10 P/50 P Coin Door ‘A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢/20¢ Coin Door 99-15067. (Lock ASI
‘A037619-08 — German 1 DM/1 DM Coin Door A037619-09 — German 2 DM/1 DM Coin Door ‘A037619-10 — an 2 DM/5 DM Coin Door A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — 5 Fr/5 Fr Coin Door A037619-13 — Swiss 1 Fr/1 Fr Coin Door A037619-14 — French 1 Fr/1 Fr Coin Door Maintenance, Repair and Parts
99-1503 (Bezel for Button)
99-1501 thru 99-15011 (Ret. Button)
99-15072 (Door Frame)
99-15071 (Clamp)
99-15039 (Bezel for Cover)
99-15036 (Cover) )
99-15066 (Screw)
9915074 (Lower Door)
‘03761915 — French 2 Frit Fr Coin Door A037619-16 — Swedish 1 Kr/1 Kr Coin Door A037619-17 — Spanish 25 Ptsi25 Pts Coin Door ‘A037619-18 — Itallan 100 L/100 L Coin Door A037619-19 — Hong Kong $1/$1 Coin Door ‘A037619-20 — Japanese 100Y100Y Coin Door
Figure 3-7 Vertically Mounted Coin Door, continued A037619-xx C
Maintenance, Repair and Parts Kangaroo™
Figure 3-7 Vertically Mounted Coin Door,continued Parts List
Part No. Description A037491-01 Coin Box (Not included in assembly) A037542-01 Harness Assembly 72-1405S #4-40 x %,-Inch Cross-Recessed Pan-Head Steel Machine Screw 7214148 #4-40 x %-\Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9145 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German i DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008. Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 1/904/-001 Lamp Base
3-20
Kangaroo™
F. Printed-Circuit Boards
Prior to removing or repairing any printed-circuit board, unplug the game.
To Remove Printed-Circuit Boards:
- Open the rear access panel.
- For the game PCBs, unplug the edge connectors. Remove the wood screws that attach the top cleat to the game cabinet, and remove this cleat. The sides of the video PCB are secured by plastic retainers. To release this PCB from the retainers, gently pry the retainers away from the PCB.
- Carefully remove the PCBs from the slots in the bottom cleat. Be careful not to twist the boards, as this may loosen connections or components. Repair as required. @ Reinstall the game PCBs, making sure they fit securely into the slots of the bottom cleat. Maintenance, Repair and Parts
Gently pry the plastic retainers back and secure the video PCB in these retainers. To insure that the game PCBs will not be damaged when you move the game, be sure to reinstall the top cleat. . For the Regulator/Audio |! PCB, disconnect the four ‘small harness connectors on this board. . Remove the screw and two spacers that secure this board to the cabinet and carefully remove the board from its slot. Be careful not to twist the board, as this may loosen connections or components. Repair as required and reinstall the board. Make sure that the connectors on the game or Regulator/Audio II PCBs are properly plugged in. Note that they are keyed to fit only one way, so if they don't slip on easily, don't force them. A reversed connector will probably damage your game and void the warranty. Close and lock the rear access panel. Check that the operation of the game is correct by performing the self-test. This is very important when you repair a PCB.
. 038423-03 (Cleat)
82-1820S (Screw)
171025-001 (Interconnector)
171023-001 (CPU PCB)
034536-02 (Vibra Damp.)
(Regulator! Audio |! PCB)
Remove in the order indicated. (Circled numbers match the numbered instructions.) 171024-001 (Video PCB)
035745-09 (Retainer)
034536-01 (Vibra. Damp.)
038423-03 (Cleat)
175004-708 (Spacer)
72-6810S. (Screw)
Figure 3-8 Printed-Circuit Board Removal
3-21
3-22 171023-001 Figure 3-9 en te! 7405139) 7aLs32] Paes]
ice pete
Tan 94a Les FAL $04] TRY 2,2, nae et toa od
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction forbidden without the speci
innyvale, CA, This drawing is only
f Atar writ
1 1e2o_ ascore ‘0, g x cee ome. 136 1649 Taesea] [fasaca] e355" ieae TAL Sod, fracs3ce] DIP sw
tes
Taisen cane] Tea Pacs3e7
[Parsee
fn) wars 123
Pravsse7. ap ioe 1c2a4 3 yy ree evecare fa) oa 7445906
in tc29
he as custom 145, SD Faus3e8 1o37 caw 74b 5367, rasoee] hac ee BES par
1c38 Pausi7s c4,a70C D> SD 39 1c47 tebe Pai ss aD TeS3
Pacsse7] [acs 1648
lego 1c40 [ausi7s
SERVICE
SwiTcH
1e54
eon ag eons
Lew, ROMS L532 [atsac7
13! Loar icao less
Passe Fatsse 748367 ep cre Maintenance, Repair and Parts
Kangaroo™ Central Processing Unit PCB Assembly ale 1e50 pr Avo19 APS B10 ® Reine
Q
o §:ad6 Se a Kangaroo™
Kangaroo™ Maintenance, Repair and Parts
Figure 3-9 Kangaroo™ Central Processing Unit PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) 34-2N6044 Type-2N6044 Darlington NPN Transistor (TR-3, TR-4)
| 37-74LS00 | Type-74LS00 Integrated Circuit | (1C13, 48) |
| 37-74LS04 | Type-74LS04 Integrated Circuit | (IC12, 35, 36) |
| 37-74LS32 | Type-74LS32 Integrated Circuit | (IC11, 21, 40, 41, 49) |
| 37-74LS42 | Type-74LS42 Integrated Circuit | (IC2, 31) |
| 37-74LS74 | Type-74LS74 Integrated Circuit | (IC30) |
| 37-74LS139 | Type-74LS139 Integrated Circuit | (IC1) |
37-74LS175 Type-74LS175 Integrated Circuit (IC38, 47, 52, 53, 58, 59)
| 37-74LS245 | Type-74LS245 Integrated Circuit | (1C23) |
| 37-74LS367 | Type-74LS367 Integrated Circuit | (IC3, 4, 14, 37, 39, 54, 55) |
| 62-001 | SPST Momentary Pushbutton Switch | (SERVICE SW) |
66-118P1T 8Station SPST, Dual-Inline-Package Switch (DIP SW) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (IC7-10, 16, 17, 24, 28) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (IC15, 34, 50)
| 82-1820S | #8 x 1%-Inch Flat-Head Wood Screw | (for mounting PCB to cabinet) |
90-7036 Random-Access Memory (IC5, 6, 32, 33) 034536-01 Foam Vibration Damper 035745-09 Plastic PCB Retainer (for mounting PCB to cabinet) 038423-03 Dual Slotted Wood Cleat (for mounting PCB to cabinet)
| 110000-101 | 100 Ohm, +5%, %W Resistor | (R27-49, 52, 53) |
| 410000-102 | 1K Ohm, +5%, %W Resistor | (R50, 51, 61) |
| 110000-103 | 10K Ohm, +5%, %W Resistor | (R2, 5, 64, RX) |
110000-122 1.2K Ohm, +5%, %4W Resistor (R7) 110000-203 20K Ohm, +5%, %4W Resistor (R4)
| 110000-221 | 220 Ohm, +5%, %4W Resistor | (R8) |
110000-331 330 Ohm, +5%, %W Resistor (R9, 10) 110000-332 3.3K Ohm, +5%, %W Resistor (R6) 110000-472 4.7K Ohm, +5%, %4W Resistor (R1) 110000-510 51 Ohm, +5%, %W Resistor (R3) 110000-512 5.1K Ohm, +5%, YW Resistor (R62)
| 118001472 | 4.7K Ohm, 4-Element, 5-Pin, Single-Inline-Package Resistor Network | (RA2) |
| 118002-222 | 2.2K Ohm, 8-Element, 9-Pin, Single-Inline-Package Resistor Network | (RA3-6) |
| 118002-472 | 4.7K Ohm, 8-Element, 9-Pin Single-Inline-Package Resistor Network | (RA1) |
| 119003-102 | 1K Ohm +20% Horizontal Trimpot | (VR2) |
121015-103 .01 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C7-30) 121015-104 1 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (Bypass, 26 places) 121020-101 100 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C2) 121020-102 1000 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C6) 121020-471 470 pF 50V Radial-Lead Ceramic-Disc Capacitor (C3-5, 34) 121021-105 1 pF, + 10%, 16V Tantalum Capacitor (C35) 121022-104 0.1 pF, + 10%, 50V Polyester Film Capacitor (C36) 123004-101 100 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C42) 123004-470 A7 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C39-41) 123004-471 470 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C37)
[Continued on next page]
3-23
Maintenance, Repair and Parts Kangaroo™
Figure 3-9 Kangaroo Central Processing Unit PCB, continued Parts List
Part No. Description
123005-225 2.2 uF, + 20%, 50V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C1) 123006-106 10 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C38) 133010-001 Type-2SC372 NPN 50V 400mW Transistor (TR1, 2) 136008-101 Programmable Read-Only Memory, #75 (IC7) 136008-102 Programmable Read-Only Memory, #76 (IC8) 136008-103 Programmable Read-Only Memory, #77 (IC9) 136008-104 Programmable Read-Only Memory, #78 (IC10) 136008-105 Programmable Read-Only Memory, #79 (1C16) 136008-106 Programmable Read-Only Memory, #80 (IC17) 136008-107 Programmable Read-Only Memory, #81 (1C24) 136008-112 Programmable Read-Only Memory, #82 (IC28) 137168-001 Type-74LS368 Integrated Circuit (IC42-46, 51) 137177-001 Type-74LS138 Integrated Circuit (IC22) 137194-001 280 Microprocessor (IC15, 34) 137221-001 Type-74LS155 Integrated Circuit (IC20) 137222-001 Type-G.|. AY3-8910 Sound Integrated Circuit (IC50) 137223-001 Audio Amplifier Integrated Circuit (IC61) 137224-001 Microcomputer Custom Integrated Circuit (IC29) 171022-001 CPU PCB, Video PCB and Interconnector Assembly 171023-001 Central Processing Unit PCB Assembly 171025-001 50-Pin Flat Cable PCB Interconnector, Fujitsu FCN-707B050-AU/B 179100-050 50-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M (CN1)
3-24
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
3-26
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction forbidden without the specific written
permission of Atari, Inc., Sunnyvale, CA. This drawing is only condi-
tionally issued, and neither receipt nor possession thereof confers or
translers any fight in, or license to use, the subject matter of the
drawing or any desigh or technical information shown thereon, nor
any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this ‘drawing or the subject matter thereof, unless by written agreement
with or written permission from the corporation
Figure 3-10 Kangaroo™ Video PCB Assembly 171024-001 veh ere, \e50_ tees icv tea tector tenis tesa vasa] [iausis7 Testes] feuscea] [ewes] [eens] fess] [ecsod] [rusia ee rea ics) icon ters teas ice _te130 [csi] [riss7] Tacsis7] fasie7] acsis?] fiacsies] [estes] [asics] [asia] ap
a> a> @Q &e_> fare) ap 1e3 rans ic25) 1638 ise 107 1689 GpPicios GDici rare [ass] Gases] [assez] [rse7] Facssa] Persie] [arses] [racsio mom vi nom vo — Bica 11s je2e 1639 1690 1etoa tone (e132 facsis] [asics] Praisis7] [acsscr css = Taces?] [recsaq] [facooo] [aus7a 1c27 tea Rom v3 pomve teas eros tetg e133 7acsoa] [rarsse7 7arso4] [74csoa] [Pareto] [ratsio | 1c28 tear tesa ices e768 Lege (clee_ e120 tei fais] [atsza] [musis7] [vasis7] fmusis?] [aesis? fatsoo] [arson]
4is0o 2 fara} —aj@a rary =) ary tee 1ce9 ‘can (css. ieee 1679 1c93 tc107 tei cis T5175] [acsr73] [e153] fooo-oa] focones) fovorroc] [oor] facsis7] [racsos] [Farsoo ics. (iz 1630 tc43 1cse 1ce7 1c60 toga rcros Graze cise [acst4 Tal Soe 74580 74153 fcoor7-00i] [iooe17-00] fiovei7-00f [iooerr-00] [racsts 7 Pans 9s racs3e e we te iy =
: Ae zo B20
th : cue
ent i loge, lev
lee tere 1e3t teae 1c57 ices eat as 6109 1er2zd 16137, Facs7a] [Tecsi75] [racsi93] [Gass] [eoorrco] [focorrca] [becca] [ooonee] fasis7] [ases] [rausio le? fray 1632 (eas 1658 teee coz ae ero fares e138 faisi75]| [7atsoo! 7atsee] [7ais3] [lecon-co} [focoir-co] [focorr-o«] [rocoircai] [rausis7] [raises] [racsse a> > aD ab ap aD Diese 159 170 1c63 1097 cance cise 74us08] [racsee] [74153] [lecoi7-0n] [fccorcol] [leooreei] [rococo] farsis7] [farses] [ratsoo
: Ff : y
ae. : az ei ice 1c20 aLsoa £4, 33 Pies (c2t 1e34 1e47 cco fez (cea fer reve tc1ze_ ciao Pasta] [paissea] [Facsec] [7#i53] [ocorrcn] [fecorsa] occirec] [ecorse] [asia] [riser] passe
= [asses] [ersec] [7=153] co Bicez teas cae cat tere. tas teas tens ee teat rasse] asic] [sec] [rasa] [ecovsa] [ooansa] [acorn] foooree] [ausis3] [aises] [ars
H i i \c2g tco@ eae cece eee eros, faisoa] fitss03] [asec] [paisa] [ooor-ca] [Georoe] [ooorrea] [ocevr-co] [ausisa] [acsos] [ese iow BS <> <p <—@ 100m, ©) 7BBO10O1E © foun Maintenance, Repair and Parts Kangaroo™
Kangaroo™ Maintenance, Repair and Parts
Figure 3-10 Kangaroo Video PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 37-74153 | Type-74153 Integrated Circuit | (IC42-49) |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (IC 19, 105, 106, 118, 120, 134, 135, 139) |
| 37-74LS04 | Type-74LS04 Integrated Circuit | (IC8, 11, 17, 91, 115, 117) |
| 37-74LS08 | Type-74LS08 Integrated Circuit | (IC20, 27) |
| 37-74LS10 | Type-74LS10 Integrated Circuit | (IC22, 119, 131, 133, 137, 141) |
| 37-74LS32 | Type-74LS32 Integrated Circuit | (IC10, 89, 90, 104, 136, 138, 140, 142) |
| 37-74LS74 | Type-74LS74 Integrated Circuit | (IC5, 6, 9, 28, 41, 132) |
37-74LS86 Type-74LS86 Integrated Circuit (IC30, 32-36)
| 37-74LS95 | Type-74LS95 Integrated Circuit | (1C121-128) |
| 37-74LS157 | Type-74LS157 Integrated Circuit | (IC 12, 13, 25, 26, 51, 54, 64, 65, 75, 78, 92, 107-114) |
| 37-74LS163 | Type-74LS163 Integrated Circuit | (IC1, 2, 14, 15, 50, 63, 74, 88, 102, 116) |
| 37-74LS174 | Type-74LS174 Integrated Circuit | (IC 129, 130) |
| 37-74LS175, | Type-74LS175 Integrated Circuit | (IC3, 4, 7, 16, 18, 87, 101, 103) |
| 37-74LS193 | Type-74LS193 Integrated Circuit | (1C29, 31) |
| 37-74LS367 | Type-74LS367 Integrated Circuit | (IC38-40) |
| 37-74LS393 | Type-74LS393 Integrated Circuit | (IC21, 23) |
78-801001F PCB Plastic Standoff 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (IC52, 53, 76, 77) 90-123 1OMHz Crystal (XTAL—Left of IC9) 100017-001 Random-Access Memory (IC55-62, 66-73, 79-86, 93-100)
| 110000-122 | 1.2K Ohm, +5%, YW Resistor | (R4) |
| 110000-221 | 220 Ohm, +5%, %W Resistor | (R1, 3, 9-12) |
| 110000-561 | 560 Ohm, +5%, YW Resistor | (R2) |
121015-104 -1 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (Bypass, 38 places) 121020-330 33 pF, + 10%, 10V Radial-Lead Ceramic-Disc Capacitor (C4) 123004-101 100 uF 16V Aluminum Electrolytic Radial-Lead Capacitor (C1, 3)
| 136008-108 | Programmable Read-Only Memory, #83 | (IC76) |
| 136008-109 | Programmable Read-Only Memory, #84 | (IC52) |
136008-110 Programmable Read-Only Memory, #85 (IC77)
| 136008-111 | Programmable Read-Only Memory, #86 | (IC53) |
179100-050 50-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M (CN1)
3-27
Maintenance, Repair and Parts Kangaroo™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING R33 CONFIDENTIAL: Reproduction forbidden without the spe- {exp cific written permission of Atari, Inc., Sunnyvale, CA. This o ‘drawing is only conditionally issued, and neither receipt nor qe possession thereo! confers or transters any right ny OF Tr
| = | 4 | | | Gense to use, the subject matter of the drawing or any de- | |
| ¢| | cea | Q | Sign or technical Information shown thereon, nor any right | |
| g | oN) | OS | to reproduce this drawing or any part thereat Except for | |
| ER? | 2] | 0 | manutacture by vendors of Atari, Inc,, and for manufacture | |
| = | oR | 25 | ° | Under the corporation's written license, no right to repro- |
= duce this drawing is granted or the subject matter thereot
| = | wg | ae | unless by wiitten agreement with or written permission | |
| c20 | ca! | 0 | ec | from the corporation. |
x C19 NX ce 3300 35V |
C18
| 2a | c23 | c3I |
| 0 | eA | +F22}+ |
einF} _
| A256 | ie | 4-22 | |
| p32 | = | cee | Zac |
| £3 | —-{405wl | i) |
5.6K = G8 Q9 pes} 7812 7905
a fe) 33 R24,10.7W oO z &
TIP 32
| S202 | indaooz | i |
CR} fi leo R542 7 wh + fs 20 Re
| 0 | x2 | 2S |
ceam@ j-\< [oS
ee 1
| 0 | zk] | 28 | one |
| <s | 44 | xan |
- & 4 clos
Figure 3-11 Regulator/Audio |! PCB Assembly A035435-06 B
3-28
Kangaroo™ Maintenance, Repair and Parts
Figure 3-11 Regulator/Audio Il PCB Assembly Parts List
| Part No. | Description | (Reference Designations and Locations in Bold) |
19-100P1015 .1 Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8)(Acceptable substitute is part no. 119002-102.) 24-250108 1000 pF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13) 24-250477, 470 uF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C1) 24-350226 22 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C24, 31) 24-350338 3300 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C18, 19) 24-500105 1 uF 50V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C22, 23) 29-088 -1 uF 50V Ceramic-Disc Axial-Lead Capacitor (C20, 21) 31-1N4002 Type-1N4002 100V 1-Amp. Siiicon Rectifier Diode (CRI, 4) 31-1N5401 Type-1N5401 100V 3-Amp. Silicon Rectifier Diode (CR5-8) 33-TIP32 Type-TIP32 PNP Power Transistor (Q2) 34-2N3055 Type-2N3055 NPN Silicon Transistor (Q3) 37-LM305 5V Linear Voltage Regulator (Q1) 37-7812 Type-7812 + 12V Voltage Regulator (Q8)
| 37-7905 | Type-7905 —5V Voltage Regulator | (Q9) |
72:-1608C #6-32 x ¥e-Inch Cross-Recessed Pan-Head Corrosion-Resistant Stee! Machine Screw 726812S #8 x 34-Inch Phillips-Head Wood Screw (for mounting PCB to cabinet) 75-F60405, #6-32 x 14-inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly 78-16014 Thermally Conductive Silicon Insulator (Q2, 9)
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346, | 12-Position Connector Receptacle | (J10) |
034531-01 Heat Sink 034536-02 Foam Vibration Damper (goes between PCB and cabinet wall) 410000-100 10 Ohm, +5%, %W Resistor (R29, 30) 110000-101 100 Ohm, +5%, %4W Resistor (R4) 110000-271 270 Ohm, +5%, ¥4W Resistor (R1) 110000-330 33 Ohm, +5%, %W Resistor (R3) 110000-392 3.9K Ohm, +5%, %4W Resistor (R6) 110000-562 5.6K Ohm, +5%, %W Resistor (R32, 33) 110006-752 7.5K Ohm, +5%, YW Resistor (R7) 110009-027 2.7 Ohm, +5%, 1W Resistor (R5) 116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 116001-040 4 Ohm, +5%, 5W Wirewound Resistor (R25) 122002-102 .001 uF 50V Ceramic-Disc Axial-Lead Capacitor (C2) 122004-224 .22 uF 25V (min.) Ceramic-Disc Axial-Lead Capacitor (C8)
| 175004-708 | Fiber Spacer | (for mounting PCB to cabinet) |
| 179051-001 | Test Point | (Acceptable substitute is part no. 020670-01) |
3-29
Maintenance, Repair and Parts Kangaroo™
G. Power Supply Assembly
A035888-01 (Transformer) 29-053 (Capacitor)
A021084-xx ! ! (Volt. Plugs) Fuse cover must be 9
in place during game operation. 034544.01 (Fuse Block Cvr.)
79-4411001 (Fuse Post)
46-2017002 (Fuse)
A035891-01 (Fuse Harness) 034482-02 (Chassis)
46-301203 (Fuse)
037639-01 (Label)
78-2708 (Bushing)
A034630-01 (Fase Bloc (titer Assy) 037641-01 46-2014002 Label _ (Fuses)
79-15021001 'A035890-01 (Term. Block) \ (Pwr. Harness) A034629-01 3A-MDA3501 (AC. Ham) (Rectifier)
Figure 3-12 Power Supply Assembly A037671-01 and -02 C
3-30
Kangaroo™ Maintenance, Repair and Parts
Figure 3-12 Power Supply Assembly, continued Parts List
Part No. Description (Reference Designations in Bold) A021084-01 Voltage Plug for 100V (violet)
| A021084-02 | Voltage Plug for 120V | (yellow) |
| A021084-04 | Voltage Plug for 220V | (blue) |
| A021084-05 | Voltage Plug for 240V | (brown) |
A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly (FL1)
| A035888-01 | Transformer Assembly | (T1) (Acceptable substitute is part no. A035888-02) |
A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053 27,000 pF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type-MDA 3501 (CR1) 46-2014002 4-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%.-Inch Outside Diameter x Y-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 03448202 Power Supply Chassis 034544-01 Fuse Block Cover 037243-01 Metal Base Plate (goes under the power supply—not shown in illustration)
| 037639-01 | Label for Fuse Value | (F1) |
| 037641-01 | Label for Fuse Values | (F2-F6) |
Line Voltage Range Voltage Selection Plug Wire Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow* 200-240 VAC (220) Blue 220-260 VAC (240) Brown *This is the only plug provided on the North American power supply.
A037671-01 power supply assembly has the 120V plug A037671-02 has the 100V, 220V and 240V plugs A037671-03 has the 220V and 240V plugs
NOTES:
NOTES:
NOTES:
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm QO Distributor
Address O Operator
City State Zip O Other. Kangaroo™ ‘3rd printing
Area Code Phone
First fold
No Postage Necessary if mailed in the United States
BUSINESS REPLY MAIL a FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA es
POSTAGE WILL BE PAID BY ADDRESSEE be Atari, Inc. Es Attn.: Field Service/Coin-Op Division ee P. O. Box 427 Sunnyvale, California 94086 Pe a a
Second told
WOl4 e6pe siyy adey =
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm U Distributor
Address. O Operator City Country U Other. Kangaroo 3rd printing
Phone City Code Country Code
First fold
Attach Necessary Postage
Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland
1WOl4 eBpe sy) ede,
9 EE REE ILE
> > ° > > >
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, al its option, to repair, replace. or credit Buyer's account for such products which are returned to Seller during said warranty period, provided
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
- Such products are returned prepaid to Sellers’ plant, and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident. misuse. neglect. alteration, improper repair. installation or improper testing
In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever. and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. : : : : : : :
ATARI INC 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488 a
ad 4.9."