War of the Bugs (Kit for Galaxian PCB)
War of the Bugs · Document · 3 pages · 1 sections · original scan
Instructions for War of the Bugs on single Galaxian board,
- Make sure the Galaxian board iy 100% functional before attempting the conversion.
- Cut the track going to pin 1 of IC 2B (74366).
- Cut the track on the bottom of the board going to pin 21 of I¢ 1K (2716 eprom).
4, Cut the truck on the bottom of the board going to pin 21 of IC 1H (2716 eprom).
- Join pins 21 of IC's (if and 1K together and connect both to pin 1 of IC 2N (7408),
- Remove IC's 1H and 1K and replace with new eproms supplied (2732), ensuring that they are inserted in the same direction as the originals,
- Remove program rom board and replace with new board supplied , ensuring that the eproms face the same way as before.
- Remove IC 6L and replace with new IC supplied .This IC may be soldered into the board = in which’ case it should be replaced with an IC socket and the new IC placed in the socket.
- Install new controls in the machine and wire up as per the connection diagram supplied. For an upright machine only the 1 player controls need to be connected.
- Double check all work done on the board, particularly the direction of all IC's replaced as an incorrectly inserted device will be destroyed.
CONVERSION INSTRUCTIONS
Installation:
- Conversion of Existing Board. Install board in machine. If new controls are required (i.e. 4 way joystick) connect to the edge connector according to the connection diagram supplied. Note that all controls are connected to a common ground - i.e. one side of every switch is grounded.
- Installation of New Board. Re-wire the edge connector according to the connection diagram supplied.
Common Problems and Solutions.
- Random character on screen/frozen display or game resets itself during play - usually caused by incorrect power supply voltage. Ensure voltage on the board is +5 volts + —0.25 volts. Voltage should be measured at the board because there could be as much as % volt drop on the leads from the power supply, which could stop the board from working correctly.
- Not accepting credits or control not functioning. Ensure one side of coin micro or control switch is connected to ground (0 volt). To check connection/operation of switches measure voltage across switch - should normally be about 4.5 volts dropping to zero when switch is operated.
- Wrong Credits - Check dip switch settings on the board, check lead from coin i/p is connected to correct pin on edge connector - there is often more than we credit i/p to the board but for different coins. Also, there may be a “credit board” or small printed circuit board with dip switches - connected between coin mechanism and main logic board - if so check switch settings.
- Game runs but picture unstable - check connection to monitor including, the ground connection. If picture is blue and unstable the sync and blue connections are reversed. If picture is steady but off set - i.e. moved up or down the screen then sync is wrong polarity. Most monitors have two sync inputs (+ ve and — ve) then change sync connection at monitor.
WAR_OF THE BUGS VIDEO GAME.
ALL SWITCHES RETURN TO O VOLTS,
ALL COUNTERS RETURN TO +12 VOLTS.
VIDEO LOGIC BOARD PIN OUT DETAILS.
| 0 VOLTS | A | 1 | 0 VOLTS. |
| 0 VOLTS | B | 2 | © VOLTS. |
| +5 VOLTS | c | 3 | +5 VOLTS. |
| +5 VOLTS | D | 4 | +5 VOLTS. |
| N/c | E | 5 | n/c. |
| N/c | F | 6 | n/c. |
| N/c | H | 7 | n/c, |
| 25 CENT CREDIT | J | 8 | TWO PLAYER UP (TABLE TOP) |
| ONE PLAYER DOWN | K | 9 | ONE PLAYER UP. |
| ONE PLAYER START. | L | 10 | TWO PLAYER START. |
| ONE PLAYER LEFT. | M | 11 | ONE PLAYER RIGHT. |
| ONE PLAYER FIRE. | N | 12 | TWO PLAYER FIRE(TABLE TOP). |
| TWO PLAYER LEFT(TABLE TOP) | P | 13 | TWP PLAYER RIGHT(TABLE TOP). |
| N/c | R | 14 | TWO PLAYER DOWN (TABLE TOP). |
| © VOLT SCREEN | s | 15 | © VOLT SCREEN. |
| GREEN VIDEO | T | 16 | RED VIDEO. |
| SYNCH | U | 17 | BLUE VIDEO. |
| N/c | Vv | 18 | AUDIO OUTPUT. |
| +12 VOLTS | Ww | 19 | +12 VOLTS. |
| +12 VOLTS | x | 20 +12 VOLTS. | |
| O VOLTS | Y | 21 | 0 VOLTS. |
| oO VOLTS | z | 22 | O VOLTS. |
FOR TABLE TOP GAME, SHORT SPECIAL LINK ADJACENT TO PIN S OF EDGE CONNECTER, ON THE COMPONENT SIDE OF THE BOARD.
DIP SWITCH SETTINGS.
| 1 OFF | 2 OFF | 1 COIN PER CREDIT. |
| 1 OFF | 2 ON | 2 COINS PER CREDIT. |
1 ON 2 OFF 2 COINS PER CREDIT.
| 1 ON | 2 ON | FREE PLAY. |
3 OFF 4 OFF 1 ROCKET.
| 3 OFF | 4 ON | 3 ROCKETS. |
3 ON 4 OFF 2 ROCKETS.
| 3 ON | 4 ON | 4 ROCKETS. |
POSITIONS 5 & 6 NOT IN USE,
CONTROLS REQUIRED. (UPRIGHT MACHINES).
1 OFF Joystick control, 4 way switch to O Volts. 3 OFF Push Button switches to O Volts.