Outrun Standard Sitdown
Out Run (sitdown/upright, Rev B) (Sega, 1986) · Manual · 62 pages · 33 sections · original scan
Rs So Xs Re Sy Xs Sr Xe Sy Ks Sry Xo Ro Ke Ny Ss Br Bs Ke Ks Mr So Ro Rnd Be Rohn PSB
SEGA
STANDARD TYPE
OWNER’S MANUAL — BMH BHM HHH HHH MHBHMHH MH HBM HHH HMMM MH Ho HMM HHH VHMHHBMHE
SEGA ENTERPRISES,LTD. ECP ECEC SREP CLEC CR ECRCCCRECCC EE ORE MANUAL NO. 420- 6315-01 BBW YP YP PW AP GO OP GP YP YP WWD HP BP BP YP YP APY WP BP BP AP YP AP AO YO P YO TP GP YP YP HP YP AP AP YP YP BPO GPP HPAP
a
es 2n fe
i.
12.
13.
15.
16.
17.
18.
19.
20.
21. INTRODUCTION OF THE OWNER’S MANUAL vereeeeeecttes 1
HANDLING PRECAUTIONS cvivvccssscsessscercteseeesetese tees seeereeeneetaeeteaseseseenraeeces 1
PREVENTION OF COUNTERFEITING AND CONVERSION 9 ------1------- 2
PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION +--+ 3
NAME OF PARTS cvvceseseseececeseseseceseeeseerseeeeeesenerceeeaeeeneaeeceseeeneaeseenteaes 4
BREAKER 5
DISASSEMBLING FOR THE PURPOSE OF TRANSPORTATION -------------- 6 REMOVING THE SHIPPING PLATES vevssesscscccesceescerteeeserenenteee eer tieeeeeeeees 8 OUTSIDE MONITOR cvvvescsseseeeeeesceeeeteeeeteeeseae cee eeecseeeseneeeeeeseectseeeneenee 9
PRECAUTIONS FOR INSTALLING AND MOVING THE MACHINE -------- 10
REMOVING THE GAME BOARD (vrveeeessecccersseceeeerrecerteereneenreteeeeeetereeeenen YW
MOVING THE SEAT POSITION veccccceesccccceeersteeeteeeeeereeeerrneeeeneereecenneneeees 12
OPENING THE MECHANISM BASE stecesccccescercrcccrerssreeeeetteeeeceteeeseetteeeteens 13
DISASSEMBLING AND ADJUSTING THE HANDLE UNIT veer 14
DISASSEMBLING AND ADJUSTING THE ACCELERATOR AND BRAKE -- 15
ADJUSTING THE ACCELERATOR/BRAKE POTENTIOMETER -----00--- 16
ADJUSTING THE ROLLING MOVEMENT ----vvriicreectrrcirrrerreceeees 17
REMOVING THE MECHANISM UNIT vvvvvecceereccecceceteccereeeseeetteteeeneerenentes 18 LUBRICATION -evvevesccceceeceeetecereee sense censor ceeeeeeeneeesersneaeesneanenseenseees A vacaees eng vas 19 - 20
ADJUSTMENT AND REPLACEMENT OF THE V BELT +000 ree reer a
ADJUSTING THE LIMIT SWITCH AND THE HOME POSITION SWITCH --: 22
REPLACING THE MOTOR BRUSH vvvestccecessecceeeteeeetreertteenestteeeeeeeeerereteneee 23
ADJUSTMENT OF THE SERVICE SWITCH vcs 24 DIP SWITCH SETTING (cccccceccecceeeseeeeteeiereeeneeee teen eenentereeeeees sag EMER Agenee 25 EPROM/ROM LOCATIONS vvvrcescscsceetrettissee tices seer ete tie ecerernensnreees 26. 27
GELEF—TESTING vvcvresvecsceceeseerseeceeneeneeeceeseneesenssseeeereercncaeteereeeserseeeeeereanes 28~34
PARTS | OF (sy eRe 35~58
WIRING DIAGRAM (cvecesceeccseseeseseseeseeeteseeeeeeeeeeeneeieneensenensseetereeiereneieees 59
SPECIFICATIONS ¢ INSTALLATION SPACE : |A TYPE) 1130 mm ( 44. simmax | 1840 mm (72,5 in. )D
IB TYPE} 1130 mm ( 44.5 in. ) W 1740 mm ( 68.5 in. ) D 1695 mm ( 66.7 in.) H (1600 mm W/O Billboard H ) ¢ POWER : 305 W © CR.T. : 20inch ¢ WEIGHT : 300kg.( 661 lbs.)
INTRODUCTION OF THE OWNER’S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic 4 technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER'S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the OUT RUN,
a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in
Ics, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there
be a malfunction, non-technical personnel should under no
circumstance touch the interior system.
- HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.
o Be sure to turn the power off before working on the machine. o To insert or pull out the plug quickly is dangerous. o Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner sO aS to be dangerous. Make sure that grounding connections are made safely at the position where so specified. oO Do not use any fuse that does not meet the specified rating. o Make complete connections for the IC board and other connecters. Insufficient insertion is very dangerous.
Also, for the Ic board circuit inspections, only the logic
tone is allowed. The use of a tester is not permitted, so be
careful in this regard. After confirming that there are no irregularities, turn the power ON.
2, PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING
To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.
ORIGINAL SEAL LICENSE SEAL
The following seal is put on The following seal is put on the the machines manufactured by kits, such as the printed SEGA. circuit boards, of SEGA products.
or PROGUET 15 sanvrACTUaeD. UNOER “The LICENSC'OF tet tte tee tt ete oe te
COPYRIGHT NOTICE
This SEGA product has the copyright notice as follows:
© SEGA 1986
This signifies that this work was disclosed in 1986 and is the property of SEGA ENTERPRISES, LTD. ,
- PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The OUT RUN is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in Places mentioned below so as to ensure proper usage:
o Places subject to rain or water leakage, or condensation due to humidity. o In the proximity of an indoor swimming pool and/or shower. o Places subject to direct sunlight. o Places subject to heat sources from heating units, etc., or hot air.
o Vicinity of highly inflammable/volatile chemicals or hazardous matter. o Sloped surfaces. o Vicinity of anti-disaster facilities such us fire exits and fire extinguishers. o Places subject to any type of violent impact. o Dusty places.
INSTALLATION OF THE “OUT RUN”
© Use an independent outlet for the power supply. (The breaker may break when the maximum current is consumed if the outlet is simultaneously used for the power source of other machines.)
© When using an extension cord, use one with a specified rating or higher.
RATED CURRENT
MAXIMUM
For installation, make doubly sure that attention be paid to the above points.
- NAME OF PARTS
20° MONITOR a KR-0021
SEAT UNIT KR~-1082 WOODEN CABINET KR-10003
~~] HANDLE UNIT
KR-1100 COIN CHUTE BOX mE ACCEL & BRAKE UNIT
KR-1200
sn MECHANISM BASE
KR-20003 SHIFT LEVER UNIT KR-13001
TOOLS
(TAMPERPROOF WRENCH) (TAMPERPROOF WRENCH)
M4 540- 0006-01 M5 540- 0007-01 M4 540-0018 M6 540- 0015-01 MS 540-0017 M8 540~- 0009-01
- BREAKER
When the machine is overloaded, the breaker functions and : the machine will stop. In such a case, check the breaker shown below, and if it is protruding, this signifies that the breaker has performed its function. After finishing checking, push it forward to restore the breaker to its original position.
MAIN FUSE (15 A)
EARTH TERMINAL
- DISASSEMBLING FOR THE PURPOSE OF TRANSPORTATION
When disassembling for the purpose of transportation, follow the procedure below: nett at ea dante ae
MOVING CABINET
LINK BALL El SERVICE DOOR oO in
PROCEDURE
@ Take off the 4 M8 bolts which secure the anti-roll bar and the moving cabinet.
@ Take off the link ball's M18 nut located inside the service door which can be opened by removing the 4 tamperproof
screws.
@ Take off the shoulder screw attached to
the rod end.
Anti-roll bar
The machine can be disassembled in accordance with the above procedure. However, be sure to disconnect the connectors and cord clamp. There are a total of 28 connectors of 7 kinds, and one earth wire. When installing the moving cabinet directly on the floor, pay particular attention so that no sudden pressure is applied to the link ball.
-§-
DISCONNECTION OF THE BASE AND CASHBOX
PROCEDURE
@ Disconnect the 4 CONNECTORS inside of the CASHBOX, the COIN
CHUTE DOOR's earth wire and the 2 CORD CLAMPS.
@ Next, disconnect the CASHBOX from the BASE by removing the 5
M8 BOLTS.
j . REMOVING THE SHIPPING PLATES !
Before using the game, be sure to remove the shipping plates. There are a total of 3 shipping plates, i.e., two (A) in the front and one (B) in the rear (see illustrations below).
To remove shipping plate A, take off the 2 M6 hexagon bolts and M5 screws.
To remove shipping plate B, take off the 3 M8 hexagon bolts and pull it upward. gS pie
- OUTSIDE MONITOR
o The outside monitor can be connected via the RGB output/SYNC GND output terminals to the machine. o For the outside monitor, be sure to make the connection from the secondary side via an appropriate transformer.
When using the outside speakers, use a power amplifier via the lineout terminals (sound output jacks).
CAUTION : The IC board will be damaged if the AC power is directly
applied without using the transformer.
o Make sure that the video cable is no more than 10 meters
long so as not to deteriorate the quality of the on-screen graphics.
SYNC GND OUTPUT RGB OUTPUT
LEFT SIDE SOUND RIGHT SIDE SOUND
OUTPUT JACK OUTPUT JACK
[ 7 OUTSIDE MONITOR
ROE % OUTLET
q SYNCGND AUDIO AMP, TRANSFORMER ge D JACK / QUTSIDE SPEAKER
- PRECAUTIONS FOR INSTALLING AND MOVING THE MACHINE
PRECAUTIONS FOR INSTALLATION
The machine is provided with 4 castors and 4 adjusters. When installing, make sure that the clearance between the floor and the castor is approximately 5 mm (if the clearance is insufficient, the machine will move and thus create a dangerous situation).
MOVING THE MACHINE The machine weighs approximately 300 kg. (661 lbs.) and as such, you should lift up the leg adjuster when moving it about on the floor.
CASTOR LEG ADJUSTOR
FLOOR: APPROXIMATELY 5 mn
- REMOVING THE GAME BOARD
By opening the cabinet's service door (KR-1078), the board which is located in the shield case as shown below, can be
seen.
As shown below, the board can be adjusted after removing the shield cover by taking off the 2.M4 screws. Bring the base forward and remove the board by taking off the 2 M4 screws which secure the spring.
- AMP 10P ~~ (Vee. GND)
. RGB SYNC. / MOLEX 6P GAME BOARD BASE ; SOUND (TO MONITOR) (KR—0044) / TO THE OUTSIDE \ SOUND TERMINAL i AMP 20P _26P FLAT AMP 50P MOLEX 4P TO DRIVE BD 1/0 GROUP SOUND
- MOVING THE SEAT POSITION
The machine's seat position can be adjusted in the following procedure:
PROCEDURE 1. Remove a total of 4 bolts, i.e., 2 in the front and 2 in the rear, which secure the seat.
- Carefully disconnect the connector from the bottom seat.
- Make forward or backward adjustments of the seat by removing the 4 hexagon nuts.
2 BOLTS (M8 x 30) ai 2 BOLTS (M8 x 30)
The seat can be adjusted forward/backward to 5 positions.
' : p—— BASE
ee HEXAGON NUT
530 55 80105 PAY o>
Forward/backward adjustments can be made to 5 positions.
- OPENING THE MECHANISM BASE
o The inside of the mechanism base contains the moving mechanism which is a special feature of the machine and the power Supply unit.
o Open COVER SC when servicing of the power supply is required. The cover can be removed by taking off the 3 M5 x 10 TAMPERPROOF SCREWS.
o When servicing the mechanism, open COVER SA and SB by taking off the 5 M5 x 10 TAMPERPROOF SCREWS for each cover.
COVER SC KR-2063
COVER SA KR-2061 COVER SB KR~2062
- DISASSEMBLING AND ADJUSTING THE HANDLE UNIT i To open the dashboard, take off the 2 M6 TAMPERPROOF screws. i After doing this, the lamp, spring replacements and steering adjustments can be made.
M6 TAMPERPROOF SCREW
STEERING ADJUSTMENTS
1.Release the 2 adjusting screws of the potentiometer bracket and perform the necessary adjustments by changing its gear position, making sure that the variable is within the allowable extent as shown below, and then retighten the adjusting screw.
aa POTENTIOMETER
__-- ADJUSTMENT SCREW
POTENTIOMETER BRACKET
Standard value v 3H 84H} —> Minimum (33) J7CH 7DH 7EH 7FH 80H 81H 82H 8 Maximum (CB) ~=— Allowable adjustment range —»
- DISASSEMBLING AND ADJUSTING THE ACCELERATOR
AND BRAKE
To remove the accelerator/brake unit, take off the 6 MS
TAMPERPROOF SCREWS.
TAMPERPROOF SCREW (M5)
~~~ACCELERATOR/ BRAKE UNIT
--ACCELERATOR PEDAL
TAMPERPROOF SCREW (M5)
BRAKE PEDAL
- ADJUSTING THE ACCELERATOR/BRAKE POTENTIOMETER
@ Display the SELF-TESTING MODE screen shown on page 30. @ Release the adjustment screws, move the bracket, and inake adjustments so that the variable becomes 20H when the accelerator/brake is released and returns to its original position. @ Even after the above procedure has been followed, if the variable is not within the allowable range, then slightly turn the gear to make an adjustment.
ACCELERATOR GEAR
ACCELERATOR POTENTIOMETER
ACCELERATOR BRACKET
ADJUSTMENT SCREW A BRAKE POTENTIOMETER.
ADJUSTMENT —~ SCREW B :
BRAKE GEAR / ACCELERATOR PEDAL BRAKE PEDAL
ACCELERATOR
Minimum = Maximum (fully open)
- (D5) [Brake | [ich 1DH 1EH 1FH 20H 21H 22H 23H 24n | >
- —=— Allowable adjustment range ——» (CB)
- ADJUSTING THE ROLLING MOVEMENT
Display the SELF-TESTING MODE screen (see page 31 ). A variable within the 80H (+ 8) allowable range is normal. In SELF-TESTING, when the test item is set for MOVING, the cabinet will move, so pay special attention to this point.
GEAR
ADJUSTMENT SCREW
BRACKET
ADJUSTMENT screw”
POTENTIOMETER
ADJOSTING PROCEDURE
- When the cabinet stops in the middle, release the 2 adjustment screws, move the bracket to the right and the left, and make the fine adjustments as well as the backlash adjustments to the gear.
- When the variable can not be made within the allowable range
by performing the fine adjustments, move the bracket in the direction of A and then turn the gear.
Standard value
B
Minimum <— 7CH 7DH 7EH 7FH 80H 81H 82H 83H 84H — Maximum (3C) (C1) ~—— Allowable adjustment range —— >
- REMOVING THE MECHANISM UNIT
The mechanism unit can be removed as follows:
REMOVING THE MECHANISM
4 M10 BOLTS Vv BELT 4 M10 NUTS
fi —— an ; rey ope Le] |e
oe ge
@ Remove the V BELT (see REPLACING THE BELT) @ Remove the limit switch connector. ‘@ Release the shoulder screw of the rod end. (Be sure only to release the screw and do not take it off.) @ Take off the 4 nuts and 4 bolts shown above. @© Take off the rod end shoulder screw and move the cabinet to the left. (When the shoulder screw is removed, the cabinet becomes free. Pay particular attention so as not to allow unauthorized persons access to it.)
The mechanism unit can be removed by following the above procedure as described in@~@®:
~18—
- LUBRICATION
Periodical greasing of the mobile parts are required. Apply grease in accordance with the following instructions:
Lubricate the 11 points as per the illustration.
@® ROD END i
Apply grease to the surfaces of the inner ring (diagonally lined portion as -4 per the illustration). D
A @® BALL SCREW
© Apply grease to the upper/lower white guides
as illustrated.
Apply grease to the screw surfaces by hand or a spatula.
@® THRUST BEARING
Apply grease in between the upper and lower collars (the diagonally lined portion as illustrated).
DETAILS of (8 and )
Apply grease thoroughly, particularly on the D) portion, to the
thrust bearing's steel balls, by using the nozzle container type of spray grease.
When lubricating, so as not to cause any malfunction, make sure that no foreign matter such as dust, etc. gets into the
grease.
- ADJUSTMENT AND REPLACEMENT OF THE V BELT
Power for this machine is transmitted by the V belt. If it slips or is torn, it will not work properly and also is | very dangerous. Reqularly check as to the tension, wear,
and deterioration of the belt and make the necessary
adjustments and replacements well in advance of the actual need to do so.
ADJUSTMENT OF THE BELT TENSION
- Before making adjustments of the belt tension, be sure that the power is off.
Incorrect belt tension may cause damage to the shaft and bearing, or result in an earlier than usual wearing out of the belt, so making correct adjustments is of the utmost importance. For belt tension adjustments, make sure that the belt has an approximate slack of 10 mm when applying a forefinger against the middle part in between the 2 pulleys.
- Adjusting the V_BELT
MOTOR BRACKET MOTOR
o Loosen the hexagon nut which secures the motor bracket
and the motor.
HEXAGON NUT
BELT REPLACEMENT
When belts whose surfaces come into contact with the pulleys become worn or damaged, they must be replaced.
- ADJUSTING THE LIMIT SWITCH AND THE HOME POSITION
SWITCH
Make adjustments to the limit switch and the home position switch by using the following procedure:
LIMIT SWITCH
HOME POSITION SWITCH
HOME POSITION SWITCH
ADJUSTMENT SCREW 55 7 EE ome POSITION SWITCH BRACKET
_===LIMIT SWITCH ADJUSTMENT SCREW
Releasing the adjustment screw causes the LIMIT SWITCH to slide and match the
specified position. Turn the pulley by hand and make adjustments in a manner so that as illustrated, the switch works at the 10 + 1 mm position in front of the rubber stopper.
Turn the adjustment screw so as to cause the switch together with the bracket to slide, and make adjustment so that the clearance between the magnet and the home position switch +0 becomes 3 _ 9 , mm.
- REPLACING THE MOTOR BRUSH
ref ig ~~ Motor
| ee
Replace the motor brush as shown below, (Normally, replacement once in six months is recommended.)
BRUSH 601-5478
@ To remove the cap, turn it by —_ using a screwdriver, etc. © @ Take the brush (601-5478) out
for replacement.
CAP
MOTOR DC 80V 3000RPM 350-5079
BRUSH (601-5478)
© Replace the brush when it is worn out up to this line. <—— © Make sure that both the 2 brushes are replaced.
- ADJUSTMENT OF THE SERVICE SWITCH
The layout as shown below can be viewed by opening the coin chute door.
COIN CHUTE BOX ———..
COIN CHUTE DOOR
COIN SW #2
COIN SW #1
@ VOLUME ADJUSTMENT
@ DEMAGNETIZING @ TEST SWITCH SWITCH @ SERVICE SWITCH
- DIP SWITCH SETTING
GAME PRICE SETTING DIP SWA
OPTION 1{2}3}4{s5f{[s6]7]e 1COIN 1 CREDIT | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF 1COIN 2CREOITS | ON | OFF | OFF |OFF | ON | OFF | OFF | OFF 1COIN 3 CREOITS | OFF | ON | OFF |OFF | OFF | ON | OFF | OFF 1 COIN” 4CREOITS | ON | ON |OFF }OFF | ON | ON | OFF | OFF COIN SW #1 1 COIN SCREDITS | OFF |OFF | ON | OFF |OFF |OFF | ON | OFF COIN SW #2
| 1COIN | 6 CREDITS | ON | OFF | ON | |OFF | ON | |OFF | ON | OFF |
| 2 COINS 1 CREDIT | |OFF | ON | ON | |OFF | OFF | ON | ON | OFF |
3 COINS 1 CREDIT | ON | ON | ON |OFF | ON | ON | ON | OFF 4 COINS 1 CREDIT | OFF |OFF | OFF, ON | OFF |OFF | OFF | ON
| 2 COINS 3CREDITS | ON | |OFF | OFF | ON . ON | |OFF | OFF) | ON |
2 COINS 1 CREDIT 3 COINS 2 CREDITS 5 COINS 3 CREDITS 6 COINS 4 CREDITS
2 COINS 1 CREDIT 4 COINS 3 CREDITS
1COIN 1 CREDIT 2 COINS 2CREDITS
| 3 COINS 3CREDITS | |OFF |OFF | ON | ON | |OFF| OFF) | ON | ON |
4 COINS 4 CREDITS 5 COINS 6 CREDITS
1COIN 1 CREDIT 2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS
1COIN 1 CREDIT 2 COINS 3 CREDITS
| OFF | on | |OFF | ON | |OFF | ON | |OFF | ON |
| ON | ON | |OFF | ON | ON | ON | |OFF} | ON |
| ON | |OFF | ON | ON | ON | |OFF | ON | ON |
OFF | ON | ON | ON |OFF | ON | ON | ON FREE PLAY ON | oN | ON | ON | ON | ON | ON | ON | COIN SW et COIN SW #2
| GAME OPTION | SETTING | . | DIP SW B | |||||
| OPTION | 1 | 2 | 3 | 4 | 5S | 6 | 7 | 8 |
| TYPE | MOVING | OFF| OFF |
up cockriT | on | oFF
| MINI UP | OFF) | ON |
NOT USED ON | ON ADVERTISE OFF OFF SOUND ON ON
NOT USED NORMAL. OFF| OFF DIP sw
| TIME | EASY | ON | OFF |
| ADJ. | HARD | OFF| ON |
| HARDEST | . | on | oN |
NORMAL. OFF | OFF
| NUMBER OF | EASY | ON | OFF |
| ENEMY | HARD | OFF] ON |
HARDEST ON | ON
24, EPROM/ROM LOCATIONS i
GAME BD OUT RUN { A 834—6065-01 Bn (3)
@® CPU BD OUT RUN 837-6063-01 (02)
wcirg} [rc 133l to117) [16139] bead boss
VIDEO BD OUT RUN 837-6064-01 (02) LI
DIP SW
AB Coc
=TsTelelelslelel | S278 8 /8)8] 2121 | G/]8/S/O/S]oja} | Ly =lelelalslslalal 7 slele/a/a/sigjal i | Q12/9/9)/9/9)/9/9) Spats elzlelsjelelaial W2iele Bleiejols/eis}s) ess elei=lslejalslal yoleio 9]5}o|8)3/5]3/8 ele}eisieieieyet |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
- SELF-TESTING
The main purposes of these tests are to check the operations of
the game boards, to find the defects if any, to adjust the monitor colors properly, and to make sure the sounds are produced satisfactorily. It is also performed to indicate the assignments of the dip switches, check bookkeeping functions, etc.
KIND OF TESTS
- Memory Test: To check the EPROM programs and the map area of the RAMs.
- Input Test: To test the operation of the coin switch, shift lever, handle/accelerator, brake, start switch, service switch, etc.
- Output Test: To test the operation of the lamps.
- Motor Test: To check the limit switches and to make
adjustments to the machine's rolling function.
- Sound Test: To check the quality of the sounds produced by the PCB and the video disc, and to adjust the balance of the speakers.
- CRT Test: To check if the colors on the monitor are
displayed correctly.
- Dip Switch Assignment: To indicate each dip switch assignment.
- Bookkeeping: To indicate information data on average score, average play time, etc.
- Backup RAM
Clear: When the power is turned off, a backup
battery system automatically takes over, thus allowing the continuous storage of all bookkeeping data. Using this item will enable you to clear said data.
- EXIT See page 34
- TEST OPERATION
- Push the test switch and Fig. 1 will be shown on the
screen.
- Select CONTINUE or INDIVIDUAL by using the START button.
DIAGNOSTIC (3) Move the steering to bring the MEMORY TEST arrow to the desired position
( CONTINUE } MEMORY TEST arrow to the desired position. INPUT TEST OUTPUT TEST MOTOR TEST SOUND TEST CRT TEST DIP SW. ASSIGN BOOKKEEPING BACKUP RAM CLEAR EXIT SELECT BY STEERING PUSH TEST BUTTON *
FIG. 1
[CONTINUE]: o Bring the arrow sign to CONTINUE — first, and move it to one of the tests to start. Push the TEST
button, and the tests will be performed in order, one by one, starting from the test where the arrow was originally set to EXIT.
o If the START button is pushed when the arrow is at CONTINUE, it will change to INDIVIDUAL. Pushing it again returns it to CONTINUE.
[INDIVIDUAL]:
o If the arrow is at INDIVIDUAL first
and brought to a certain test which you want to conduct, only that test is performed by pushing the TEST button.
2.
- When each test is finished, push the TEST button.
case of CONTINUE, push the TEST button, and it will
automatically go into the following test. If the TEST
button is pushed in the case of INDIVIDUAL, FIG. 1 is
shown. If you want to end the test mode at this time,
bring the arrow to EXIT and push the TEST button again,
and it will return to the ADVERTISEMENT mode.
TEST ITEMS
- Memory Test:
DIAGNOSTIC MEMORY TEST 2 ROMS TEST * *
118 IC 117 iC IC 133 IC 132 IC 76 IC 57
*%& RAMS TEST * *
Ic 114 IC 115 IC 63 IC 129 IC 130 IC 65 IC 64 IC 95 IC 52 IC 62 Ic 92 Ic 51 IC 55 IC 54 IC 73 IC 72
Indication of "GOOD" following the IC No. means the IC is
all right. Push the TEST button to proceed to the
following test item:
- Input Test
DIAGNOSTIC INPUT TEST
COIN #1 START COIN #2 SERVICE LOW GEAR HIGH GEAR
BRAKE 20H HANDLE RIGHT LEFT 80H (+ 4H) ACCEL 20H
= HANDLE > «<— ACCELERATOR
7H 7DH 7EH 7FH |80Hj 81H 82H 83H 84H 1CH 1DH 1EH 1FH [20H] 21H 22H 23H 24H Standard value Standard value In the
oO Operate the dip switches. When "ON" is indicated at the right side of the corresponding item on the screen, it is OK.
o If the data value increases when pressure is applied to the accelerator's or brake's pedal, it tests out satisfactorily.
o When the tests are ended, push the TEST button.
- Output Test
DIAGNOSTIC OUTPUT TEST
- START LAMP
- BRAKE LAMP
If the start LAMP lights up, it is functioning properly. Push the TEST button when the testing has been completed.
- Motor Test
Adjustment of each limit switch, and adjustment of the rolling movement.
DIAGNOSTIC MOTOR TEST
LEFT LIMIT DATA **H RIGHT LIMIT pe CENTER DATA **H
MOTOR POSITION 80H (+8H)
The value with an asterisk (*)
represents the one automatically checked during the warm-up time.
For adjustment, see page 17
The above screen display is for the moving cabinet.
_— MOTOR POSITION > 78H 79H 7AH 7BH 7CH 7DH 7EH 7FH | 80H| 81H 82H 83H 84H 85H 86H 87H 88H Standard value
- Sound test
DIAGNOSTIC SOUND TEST
COIN IN 10. VOICE1 CHECK POINT 11. VOICE 2 SIGNAL 1 12. VOICE 3 SIGNAL 2 13. VOICE 4 SLIP 14. WAVE SAFETY ZONE 15. CHEERS CRASH 1 16. MUSIC 1 CRASH 2 17. MUSIC 2
REBOUND 18. MUSIC 3
SELECT BY STEERING PUSH START BUTTON’ SRS Peete fr
When the test has been completed, push the TEST button.
- C.R.T. Test
DIAGNOSTIC yertow C-R.T. TEST GREEN \ COLOR BAR cigur ELUE r T BLACK | RED) us| PINK WHITE
WHITE GRAY
GRAY BLACK |
C.R.T. POSITION CHECK
When the test has been completed, push the TEST button.
- DIP SWITCH ASSIGNMENTS
DIAGNOSTIC
DIP SWITCH ASSIGNMENT 1 2 3 4 5 6 7 8 DIP SW.A OFF OFF OFF OFF OFF OFF OFF OFF DIP SW.B OFF OFF OFF OFF OFF OFF OFF OFF
1234 COIN SW#1 1 COIN 1 CREDIT ___. 5678 COIN SW#2 1 COIN 1 CREDIT B 1 Present Setting of the Dip Switches. A Coin Switch Setting.
12 TYPE MOVING OFF OFF MOVING TYPE
3 ADVERTISE SOUND ON ONY ON, SEF UP Coot 56 TIME ADJ. NORMAL ON ON NOT USED NORMAL. \. 78 NUMBER OF ENEMY
Adjustment of the game time.
The appearance frequency of the other cars
Sound is emitted at the time of GAME OVER.
(8) Bookkeeping ( No sound is emitted at the time
of GAME OVER.
DIAGNOSTIC
BOOKKEEPING
Usage frequency of coin chute 1 COIN CHUTE #1 COIN CHUTE #2 COIN CREDIT SERVICE CREDIT TOTAL CREDIT TOTAL TIME OH OM PUSH START BUTTON! Usage frequency of coin chute 2
Number of coin credits
Usage frequency of service switch eooo°o Number of credits
Operating time (hour-minute-seconé)
- Only the data that falls within the range of up to 999H 59M
59S can be memorized.
The above screen indication is for testing.
When the tests are finished, push the START button and the
following will be shown:
DIAGNOSTIC
BOOKKEEPING
NUMBER OF GAME
AVE. SCORE TOP-SCORE LOW-SCORE
** GAME TIME * * TOTAL OH AVERAGE CH LONGEST 1H PUSH START BUTTON !
Every time the START button is pressed, the bookkeeping test
display is repeated.
o When the tests are ended, push the TEST button.
- Backup RAM Clear:
To clear the data, bring the arrow to "YES" and push the
TEST button.
DIAGNOSTIC
BACKUP RAM CLEAR
=» NO YES
SELECT BY STEERING PUSH TEST BUTTON /
When the test is finished, push the TEST button to end the
test (in the case of “INDIVIDUAL," however, the test mode
returns to Fig. 1 first).
- EXIT
In the state as shown in Fig. 1, operate the steering to bring
the arrow to EXIT and push the TEST button. The self-
testing will then end and return to the ADVERTISEMENT mode. q
- PARTS LIST @ TOP ASSY OUT RUN MOVING STANDARD (KR-00003) (D-1/3)
J 6) G 2
@ TOP ASSY OUT RUN MOVING STANDARD (KR-00003) (D-2/3) ‘
ITEM No, PART No. DESCRIPTION
| 1 | KR~10003 | ASSY MOVING CABINET |
| 2 | KR~1100 | ASSY HANDLE |
| 3 | KR-1200 | ASSY ACCEL & BRAKE |
| 4 | KR~1301 | ASSY SHIFT LEVER S |
| 5 | KR-14003 | ASSY COIN CHUTE BOX |
| 6 | KR-20003 | ASSY BASE & MECHANISM |
| 7 | KR-40003 | ASSY POWER SUPPLY & AMP |
| 8 | KR~-41001 | ASSY SW RGLTR & DRIVE BD |
| 9 | KR-0044 | ASSY GAME BD BASE |
| 10 | KR-0021 | ASSY CLR DSPL 20 TYPE |
| u | KR-0009 | SHAFT ROD END |
| 12 | KR-0010 | ANTIROLL SHAFT |
| 13 | KR-0020X | SHIPPING PLATE S |
| uu | KR-0012 | SHIPPING PLATE B |
| 15 | 80738X | TAG FOR SHIPPING |
16 834~6065-01,02,03,04 GAME BD OUT RUN 932-03 SEGA OUT RUN MOVING
| 18 | 81979 | STICKER SERVICE INSTR |
| 19 | 80027XY | NAMEPLATE ELEC SPEC |
| 20 | 421-6412-01 | ADJUST INSTR SHEET OUT RUN |
| al | 421-6241 | STICKER DANGER |
| 22 | 421-5800-45, | ORIGNAL SEAL OUT RUN |
| 23 | 420-5315-01 | OWNER’S MANUAL OUT RUN STANDARD |
| 24 | 80207Y | STICKER SEGA INFORMATION |
| 25 | 83602 | STICKER SERIAL NO. INFORMATION |
| 28 | SGB-1035X | KEY BAG |
| 29 | SGB-2675 | POLYETHYLENE BAG 240x370 |
| 30 | SGM~3743 | POLYETHYLENE COVER 1400x2100x1700 |
| 34 | 421-6482-01 | STICKER CAUTION |
| 35 | KR-0033 | HOLE COVER |
| 36 | KR-0034 | BODY REAR |
| 37 | 82789 | STICKER DANGER HIGH VOLTAGE |
| 38 | KR-0036 | MUDGUARD |
| 39 | KR-0037 | HOLDER MUDGUARD |
| 40 | 422-0159-02 | PLAY INSTR PLATE OUT RUN |
| 41 | KR-0038 | ASSY HEADER |
| 42 | KR-0042 | BRACKET RIGHT |
| 43 | KR-0043 | BRACKET LEFT |
| 4 | KR-0045 | NUMBER PLATE (CALIFORNIA ) |
| 101 | 601-0769 | STAPLE MAX #3 |
| 201 | 000-0516 | M SCR PH W/FS M5x16 |
| 202 | 000-0525 | M SCR PH Msx25 |
| 203 | 008-0410 | TMP PRF SCR TH M4x10 |
| 204 | 0008-0516 | TMP PRF SCR TH Msx16 |
| 205 | 010-0306-F | S-TITE SCR PH W/F M3x6 |
| 206 | 000-0620 | M SCR PH M6x20 |
000-0514-FS M SCR PH W/FS Msx14
| 207 | 046-0001 | SCR NAIL THH STAINLESS 1.5x16 |
| 208 | 059-0017 | HEX NUT M12 |
| 209 | 059-0020 | HEX NUT P=1.5 M18 |
@ TOP ASSY OUT RUN MOVING STANDARD (KR-00003) (0-3/3)
ITEM No. PART No. DESCRIPTION
| 210 | 060 | FLT WSHR M5 |
| 211 | 061-0005 | SPR WSHR M5 |
| 212 | 061-0006 | SPR WSHR M6 |
| 213 | 069-0030 | SPR WSHR M12 |
| 214 | 061-0018 | SPR WSHR M18 |
| 216 | 000-0530 | M SCR PH M5x30 |
| 217 | 000-0414-FS | M SCR PH W/FS M4x14 |
| 218 | 029-0079 | TMP PRF SCR BH M6x35 |
| 219 | 030-0830-B | HEX BOLT BLK M8x30 |
| 220 | 061-0008 | SPR WSHR M8 |
| 221 | 030-0820 | HEX BOLT M8x20 |
| 222 | 0690-0020 | FLT WSHR M12 |
| 223 | 060-0008 | FLT WSHR M8 |
| 224 | 009-0825 | TMP PRF SCR BH M8x25 |
390-5139 LAMP 140V 10W KR-1111X EXT SPRING 509-5161 SW MICRO TYPE 220-5130 * VOL CONT B-5K OHM 244-115 GREASE W/SPATULA 244-118 GREASE SPRAY TYPE 300mf W/No, 22LE 350-5085 V BELT 390-0116 LAMP WEDGE BASE TYPE 14V 0,24 601-5478 BRUSH FOR MOTOR 540-0018 DRIVER FOR TMP PRF SCR M4 540-0006-01 WRENCH FOR TMP PRF SCR M5 540—0007-01 WRENCH FOR TMP PRF SCR DUAL TYPE M5 540-0015 WRENCH FOR TMP PRF SCR DUAL TYPE M6 540-0009-01 WRENCH FOR TMP PRF SCR M8
| 225 | 000-0414 | M SCR PH W/S M4x14 |
| 226 | 005-3820 | W SCR RH 3.8x20 |
- Note : VOL CONT refers to the Potentiometer. 1
Out Rui
i \\ ——————} @ ASSY HEADER (KR-0038) (0-1/2)
@ ASSY HEADER (KR-0038) (D-2/2)
ITEM No.
Anarene PART No.
KR-0039 423-0032 KR-0040 KR~-0041 834-5536 SGB-3760-38 211-0096 211-0095 211-0167 211-0041
390-5139 214-0105
031--0410 —B 051-0003 001-0308 008-0410
000-0420 051-0004 DESCRIPTION
HEAD COVER DESIGN PLATE OUT RUN L BRACKET LAMP HOLDER PLATE -ASSY SSR _BOARD WIRE HARN HEADER CONN PLUG AMP 2P YELLOW CONN PLUG AMP 2P ORANGE TERM LUG RND IDS CONN PIN AMP
LAMP 140V 10W BULB SKT T-19
CARRIAGE BOLT M4x10 FLG NUT M3 M SCR PH M3x8 TMP PRF SCR TH M4x10
M SCR PH M4x20 FLG NUT M4
@ ASSY MOVING CABINET (KR-10003) (D-1/3)
® ASSY MOVING CABINET (KR-10003) (D-2/3) :
PART No.
KR-1089X KR-1074 KR-1082 KR-1084 KR~1085 KR-1086 KR-1088 KR-1090 KR-1091 KR-1020 KR-1097 KR-1095 KR~-1053 KR-1057 KR-1058 KR-1096 280-0419 SGB-3760-43 212-5034 211-0044 211-0060 211-0005 SGB-3740-19 211-0046 601-0460 SGB-3740-59 211-0117 211-0096 SGB~3760-2 211-0117 211-0094 601-0460 SGB-3740-33 211-0085 211-0080 SGB-3760-3 211-0100 211-0121 601-0460 SGB-3760-5 211-0043 211-0044 601-0460 SGB-3760-4 211-5105 211-0072 211-0082 211-0121 211-0081 211-0102 211-0044 211-5047 211-0116 DESCRIPTION
MOVING FRAME ASSY SUB CABINET ASSY SEAT BODY LEFT BODY RIGHT FLOOR BOARD WINDOW GLASS FLOOR MAT HOLDER WINDOW GLASS BRACKET RETAINER PLATE FLOOR MAT WASHER PLATE MAT FITTING SHAFT ROLLER TV MASK 20 HARNESS LUG WIRE HARN RGB CONN FEN 6P CONN CAP AMP 2P WHITE CONN CAP AMP 3P WHITE CONN CLAMP LOCK WIRE HARN AC FAN CONN PLUG AMP 2P YELLOW PLASTIC TIE BELT 85mm WIRE HARN FAN EXT CONN CAP AMP 2P YELLOW ~ CONN PLUG AMP 2P YELLOW WIRE HARN DEM COIL EXT CONN CAP AMP 2P YELLOW CONN CAP AMP 2P RED PLASTIC TIE BELT 85mm WIRE HARN LAMP EXT CONN PLUG AMP 2P BROWN CONN CAP AMP 2P BROWN WIRE HARN START EXT CONN PLUG AMP 4P RED CONN CAP AMP 4P RED PLASTIC TIE BELT 85mm WIRE HARN SHIFT LEVER CONN PLUG AMP 2P WHITE CONN CAP AMP 2P WHITE PLASTIC TIE BELT 85mm WIRE HARN 50P EXT CONN FEM 50P CONN CAP AMP 4P WHITE CONN CAP AMP 4P BROWN CONN CAP AMP 4P RED CONN CAP AMP 3P BROWN CONN PLUG AMP 4P YELLOW CONN CAP AMP 2P WHITE CONTACT CONN CAP AMP 2P ORANGE
©) ASSY MOVING CABINET (KR-10003) (D-3/3) ITEM No. PART No,
SGB-3760-30 212-5076 211-0072 211-0005 SGB-3760-31 211-0167 SGB-3760-32 211-0094 SGB-3760-33 211-0095 SGB-3740-60 211-0046 211-0119 211-0120 211-5088 211-5047 SGB~3740-24 211-0096 600-5133 SGB-3740-32 211-0099 211-0120 211-0041 211-0042 KR-1099 SGB-3760-37 211-0096 211-0117
100-5034 260-0018 601-0769 601-5548 270-5016 280-0425 280-5008 280-5009 209-0023 601-0460
000-420-FS 005-3113-F 008-0416 008-0525 030-0610 030-0625 030-0820-B 030-0830-B 039-0023 046-0001 059-0017 060-0018 061-0006 061-0008 069-0036 069-0034 244-063 000-0425 061-0004 DESCRIPTION
WIRE HARN SOUND EXT CONN FEM 4P (MOLEX) CONN CAP AMP 4P WHITE CONN CLAMP LOCK WIRE HARN EARTH TERM LUG RND ID 5 WIRE HARN LEFT SP CONN PLUG AMP 2P RED WIRE HARN RIGHT SP CONN PLUG AMP 2P ORANGE WIRE HARN 20P EXT CONN CAP AMP 6P WHITE CONN CAP AMP 3P ORANGE CONN CAP AMP 3P YELLOW CONN FEM 20P CONTACT WIRE HARN CRT CONN PLUG AMP 2P YELLOW CABLE & CONN 300L WIRE HARN HANDLE VR EXT CONN PLUG AMP 3P YELLOW CONN CAP AMP 3P YELLOW CONN PIN AMP CONN SOCKET AMP MAT FITTING WIRE HARN HEADER EXT B CON PLUG AMP 2P YELLOW CONN CAP AMP 2P YELLOW
LINK BALL (THK RB118) FAN MOTOR AC 100V STAPLE MAX #3 WHEEL 265x48 FERRITE SLEEVE CORE CORD CLAMP 210 CORD CLAMP 215 CORD CLAMP #21 CONN CLOSED END PLASTIC TIE BELT 85mm M SCR PH W/F & M4x20 W SCR RH W/F 3,1*13 TMP PRF SCR TH M4x16 TMP PRF SCR TH M5x20 HEX BLT M6x10 HEX BLT M6x25 HEX BLT BLK M8x20 HEX BLT BLK M8x30 HEX BLT P=i.5 M18x40 SCR NAIL THH STNLS 1.5x16 HEX NUT M12 FLAT WSHR M18 SPR WSHR M6 SPR WSHR M8 SPR WSHR M12 SPR WSHR M18 DOUBLE FACE TAPE 20mmx50m/ROLL M SCR PH M4x25 SPR WSHR M4 rennet in
& POO® _DODOQOSWE
i 7 J SQOOOQQVO ) ~G8@R @ ASSY HANDLE (KR-1100) (0-1/3)
@) ASSY HANDLE (KR-1100) (0-2/3)
ITEM No. PART No.
KR~-1101 KR-1102 KR-1103 KR~-1104 KR~1105X KR-1106Y KR-1107 KR-1108 KR-1109X KR-1110X KR-1111X KR-1112 KR-1113 KR-1114 KR-1115 KR-1116 KR-1117 KR-1118 KR-119 KR-1120 KR-1121X KR-1122 KR-1123 KR-1124 KR-1125X KR-1126 KR-1127 KR-1128 KR-1129 KR-1140 TB-2007 117-5133 KR~1137 SGB-3740-4 211-0085 211-0099 211-0100 211-0041 280-0472 601-0460
100-5035 100-5015 220-5130 509-5053 390-0116 214-0081 280-0419 DESCRIPTION
FRONT PANEL METER PANEL UPPER DESIGN PLATE WOODEN BASE HANDLE BASE STEERING WHEEL SHAFT SHAFT ARM PLATE ARM BAR STEERING WHEEL STOPPER EXTENTION SPRING VOLUME BRACKET BUMPER BRACKET BUMPER STOPPER RUBBER STOPPER PLATE COLLAR A COLLAR B SPACER A STEERING HANDLE £270 KEY A KEY B BRACKET HANDLE EMBLEM GEAR A GEAR B GEAR C GEAR D BRACKET LAMP HOLDER BOARD START PLATE STOPPER WASHER WIRE HARN HANDLE CONN PLUG AMP 2P BROWN CONN PLUG AMP 3P YELLOW CONN PLUG AMP 4P RED CONN PIN AMP FASTON RCPT 110 PLASTIC TIE BELT 85mm
BEARING #20 BEARING 210 VOL CONT B-5K OHM PUSH BTN SWIT SWITCH GREEN W/LAMP LAMP WEDGE BASE TYPE 14V 0.24A WEDGE BASE SOCKET ASSY HARNESS LUG wis
@) ASSY HANDLE (KR-1100) (0-3/3) i
ITEM No, PART No. DESCRIPTION
| 201 | 030-0825 | HEX BLT M8x25 |
| 202 | 060-0008 | FLT WSHR M8 |
| 203 | 061-0008 | SPR WSHR M8 |
| 204 | 054-0005 | U NUT M5 |
| 205 | 050-0010 | HEX NUT_M10 |
| 206 | 069-0009 | FLT WSHR 10.5~28x2 |
| 207 | 061-0010 | SPR WSHR M10 |
| 208 | 000-516 | M SCR PH Msx16 |
| 209 | 000-525 | M SCR PH M5x25 |
| 210 | 060-0005 | FLT WSHR M5 |
| 2 | 069-0001 | FLT WSHR 5.5-20-1.6 |
| 212 | 000-0408-FS | M SCR PH W/FS M4x8 |
| 213 | 000-0510-FS | M SCR PH W/FS Msx10 |
| 214 | 028-0010 | SET SCR HEX SKT CP M5x8 |
| 215 | 028-0014 | SET SCR HEX SKT CP UNBR M4x4 |
| 216 | 005—-3113-F | W SCR RH W/F 3,1x13 |
| 217 | 000-0416 | M SCR PH Maxi6 |
| 218 | 000-0425 | M SCR PH M4x25 |
| 219 | 060-0004 | FLT WSHR M4 |
| 220 | 029-0078 | TMP PRF SCR BH Mé6x16 |
| 221 | 008-0416" | TMP PRF SCR TH M4x16 |
| 222 | 008-0410 | TMP PRF SCR TH M4x10 |
| 223 | 000—-0510-S | M SCR PH W/S Msx10 |
| 224 | 010-0416-F | S-TITE SCR PH W/F M4x16 |
| 225 | 061-0005 | SPR WSHR M5 |
| 226 | 061-0006 | SPR WSHR M6 |
| 227 | 069-0022 | FLT WSHR 5.5-14x1 |
| 228 | 028-0007 | SET SCR HEX SKT CP UNBR M4x10 |
| 229 | 005-3113-F | W SCR PH W/F 3.1x13 |
| 230 | 008-0425 | TMP PRF SCR TH M4x25 |
® ASSY ACCEL & BRAKE (KR-1200) (D-1/2)
a]
(2) oN dl lo- On —WOOPED ———] 5 Go a . 9 co) FT 8 a) 8 4 |@ ©
o— Oo
Or VO @ @:
@) ASSY ACCEL & BRAKE (KR~1200) (D-2/2)
ITEM No.
Conran eawne PART No,
KR~-1021X KR-1202X KR-1203 KR-1204 KR~1205 KR~1206 KR-1207 KR~1208 KR-1209 KR-1210 KR~1211 KR-1212 KR-1213 SGB-3740-6 211-0045 601-0459 211-0041
601-5564 220-5130 601-5423 601-5410 280-0425
050-0008 061-0008 060-0008 060-0006 065-0005 000-0514-S 000-0408-S 031-0514 081-0005 028-0002 000-0408-FS 0540-0005 DESCRIPTION
BRAKE PEDAL ACCELERATOR PEDAL ACCEL & BRAKE BRACKET STOPPER BRACKET VR BRACKET PEDAL BRACKET SPRING SHOULDER SHAFT BRAKE ACCEL COLLAR TORSION SPRING TORSION SPRING SHOULDER SCREW BUMPER WIRE HARN ACCEL & BRAKE CONN PLUG AMP 6P WHITE TIE BELT 85mm CONN PIN AMP
STOPPER VOL CONT B-SKOHM GEAR 1/6 GEAR 15 26 CORD CLAMP 210
HEX NUT M8 SPR WSHR M8 FLT WSHR M8 FLT WSHR M6 E RING 5mm M SCR W/S Msxi4 M SCR DH W/S M4x8 CRG BLT BLK M5x14 FLG NUT M5 SET SCR PH SPCL M3x6 M SCR PH W/FS M4x& L U-NUT Ms
® ASSY SHIFT LEVER S (KR-13001) (D-1/2)
© ASSY SHIFT LEVER S (KR-13001) (D-2/2)
ITEM No. PART No. DESCRIPTION
| 1 | KR-1312 | SHIFT BRACKET B |
| 2 | KR-1314 | COVER BRACKET B |
| 3 | KR~1303 | STOPPER |
| 4 | KR-1320 | COMPRESSION SPRING |
| 5 | KR-1304 | SHAFT |
| 6 | KR~1315 | SUB ASSY SHIFT LEVER |
| 7 | SGB-3740-5 | WIRE HARN SHIFT SW |
211-0043 CONN PLUG AMP 2P WHITE 280-5015 FASTON RCPT 187
| 8 | KR-1316 | SPACER |
| 9 | KR-1318 | MOUNT BRACKET |
| 101 | 211-0041 | CONN PIN AMP |
| 102 | 101-5004 | STEEL BALL 28.7312 |
| 108 | 509-5088 | SW MICRO TYPE |
| 104 | 310-0012 | PAPER INSULATOR |
| 105 | 117-0141 | LOCK PLATE |
| 201 | 069-0005 | FLT WSHR SPECIAL 8,3~14,3x0.5 |
| 202 | 000--0408-FS | M SCR PH W/FS M4x8 |
| 203 | 069-0049 | NYLON WASHER SPECIAL 8.5-14x1 |
| 204 | 000-0316 | M SCR PH M3x16 |
| 205 | 069-0007 | FLT WSHR |
| 206 | 065-0006 | E RING 6mm |
| 207 | 054-0004 | M4 U NUT |
| 208 | 010-0408-F | S-TITE SCR W/F M4x8 |
a
® ASSY COIN CHUTE BOX S (KR-14003) (D-1/2)
@ ASSY COIN CHUTE BOX S (KR-14003) (D-2/2) :
ITEM No. PART No. DESCRIPTION
| 1 | KR-1406 | COIN CHUTE BOX S |
| 2 | KR-1409 | COIN CHUTE BK S |
| 3 | KR-1403 | DENOMINATION PLATE |
| 4 | KR-1420 | Sw. UNIT A |
| 5 | KR-1407 | DOOR CASH BOX S |
| 6 | KR-1408 | CASHBOX S |
7 TNG LKG
| 8 | HN-1050 | SPACER |
| 9 | MX-~-1130—-02 | DENOMI SH 25¢ |
MX-1103-03 DENOMI SH 2x25¢
| 10 | 109-0045 | HOLDER KEY TURBO UPR |
| 17 | SGB-3740-16 | WIRE HARN COIN SW |
211-0073 CONN PLUG AMP 4P WHITE
| 18 | SGB-3740-17 | WIRE HARN COIN METER |
211-0087 CONN PLUG AMP 4P BROWN 211-0041 CONN PIN AMP FASTON PCRT 187
| 101 | 220-5044-01 | MAGNETIC LOCK MASTER W/O KEY |
| 102 | 220-5046 | MAGNETIC LOCK W/KEY |
| 103 | 220-5064 | MAG CNTR 6DIG DC 5V |
| 104 | 220-5174-02 | ASSY COIN CHUTE DOOR USA 25¢ TWIN |
| 105 | 280-5008 | CORD CLAMP #15 |
| 201 | 000-0306-FS | M SCR PH W/SF M3x6 |
| 202 | 010-0406-F | S-TITE SCR W/F M4x6 |
| 203 | 012-0410 | TMP PRF SCR TH M4xi0 |
ASSY BASE & MECHANISM (KR-20003) (D-1/4)
GGOQ SPOGOO SOOO OGHE / / \ qo _
ASSY BASE & MECHANISM (KR—20003) (D-2/4)
PART No,
KR-2060 KR-2061X KR-2062 KR-2063 KR-3000 KR-3011 KR-2008 KR-2064 KR-2065 KR-2013 KR-2014 KR-2015 KR-2072X KR-2017 KR-2018 KR-2019 KR-2020 KR-2021 KR-2022 KR-2023 KR-2024 KR~2026 KR~2027 KR-2068X KR-2067 KR-2068 KR-2030X KR-2044 KR-2050 RH-3018 KR-2010 KR-2066 KR-2069 KR-2070 KR-2071X KR-2073X KR-2074 SGB-3740-22 211-0095 SGB-3760-6 211-0085 211-0080 SGB-3760-7 211-0103 211-0124 SGB-3760-8 211-0094 211-0115 SGB-3760-9 211-0085 211-0080 211-0060 SGB-3760-12 211-0095 211-0116 DESCRIPTION
BASE S COVER SA COVER SB COVER SC ASSY MECHANISM GUIDE SLIDING BAR GUIDE A. B. BAR FLOOR MAT C FLOORMAT E CORNER BRACKET RUBBER SHEET MECHA SPACER PROTECTOR G PROTECTOR B PROTECTOR C PROTECTOR D PROTECTOR E PROTECTOR F PROTECTOR BRKT A PROTECTOR BRKT B PROTECTOR BRKT C PROTECTOR BRKT E PROTECTOR BRKT F. PROTECTOR BRKT G PROTECTOR BRKT 1 PROTECTOR BRKT J ASSY MOTOR AC UNIT ASSY BANK VR UNIT RUBBER SHEET FLOOR MAT B FAN MOTOR BRACKET PROTECTOR BRKT K PROTECTOR BRKT L PROTECTOR BRKT M PROTECTOR H PROTECTOR I WIRE HARN DC FAN CONN PLUG AMP 2P ORANGE WIRE HARN LAMP EXT B CONN PLUG AMP 2P BROWN CONN CAP AMP 2P BROWN WIRE HARN AC IN CONN PLUG AMP 6P RED CONN CAP AMP 6P RED WIRE HARN SW REGU CONN PLUG AMP 2P RED CONN CAP AMP 2P RED WIRE HARN DRIVE MOTOR EXT CONN PLUG AMP 2P BROWN CONN CAP AMP 2P BROWN CONN CAP AMP 3P WHITE WIRE HARN DC FAN EXT CONN PLUG AMP 2P ORANGE CONN CAP AMP 2P ORANGE
ASSY BASE & MECHANISM (KR-20003) (D-3/4) i
ITEM No. PART No,
SGB~-3760-13 211-0098 211-0119 SGB-3760-14 211-0102 211-0123 SGB-3760-15 211-0094 211-0115 SGB~3760-16 211-0095 211-0116 SGB-3760-17 211-0082 211-0087 SGB-3760-18 211-0086 211-0081 SGB-3740-27 211-0096 211-0115 211-0080 SGB-3760-20 211-0073 211-0072 SGB-3760-21 211-0087 211-0082 SGB-3760-22 211-0086 211-0081 211-0080 SGB-3760-23 211-0096 211-0117 SGB-3760-24 211-0096 211-0117 SGB-3760-25 211-0094 211-0115 SGB-3760-26 211-0044 211-0043 SGB-3760—-35 211-0043 211-0044 SGB-3760-19 211-0073 211-0072 SGB-3760-36 211-0096 211-0117 DESCRIPTION j
WIRE HARN BANK VR. EXT i CONN PLUG AMP 3P ORANGE i CONN CAP AMP 3P ORANGE WIRE HARN LIMIT SW EXT CONN CAP AMP 4P YELLOW CONN CAP AMP 4P YELLOW WIRE HARN LEFT SP EXT “B” CONN PLUG AMP 2P RED CONN CAP AMP 2P RED WIRE HARN RIGHT SP EXT “B” CONN PLUG AMP 2P ORANGE CONN CAP AMP 2P ORANGE WIRE HARN AUDIO VR EXT CONN CAP AMP 4P BROWN CONN PLUG AMP 4P BROWN WIRE HARN SW EXT CONN PLUG AMP 3P BROWN CONN CAP AMP 3P BROWN WIRE HARN DEM EXT CONN PLUG AMP 2P YELLOW CONN CAP AMP 2P RED CONN CAP AMP 2P BROWN WIRE HARN COIN EXT CONN PLUG AMP 4P WHITE CONN £AP AMP 4P WHITE WIRE HARN COIN METER EXT CONN PLUG AMP 4P BROWN - CONN CAP AMP 3!' RROWN WIRE HARN CLUTCH EXT CONN PLUG AMP 3P BROWN CONN CAP AMP 3P BROWN CONN CAP AMP 2P BROWN WIRE HARN AC FAN FXT CONN PLUG AMP 2P YELLOW CONN CAP AMP 2P YELLOW WIRE HARN CRT EXT CONN PLUG AMP 2P YELLOW CONN CAP AMP 2P YELLOW WIRE HARN 18V EXT CONN PLUG AMP 2P RED CONN CAP AMP 2P RED WIRE HARN DRIVE EXT CONN CAP AMP 2P WHITE CONN PLUG AMP 2P WHITE WIRE HARN MUTE EXT CONN PLUG AMP 2P WHITE CONN CAP AMP 2P WHITE WIRE HARN AUDIO EXT CONN PLUG AMP 4P WHITE CONN CAP AMP 4P WHITE WIRE HARN HEADER EXT A CONN PLUG AMP 2P YELLOW CONN CAP AMP 2P YELLOW
ASSY BASE & MECHANISM (KR-20003) (D-4/4)
ITEM No.
7” PART No,
SGB-3760-39 211-0096 211-0117 211-0041 211-0042 ‘SGB-3760-40 211-5086, 211-5087 SGB-3760-41 211-5107 211-5018 211-5054 211-5055
350-5085 260-0015 310-5008 310-5010 310-5018 601-0460 601-5526 601-0460 601-5526 280-5008 280-5009 000-0450 000-0510-FS 008-0510 029-0047 030-0830 039-0008 050-0010 060-0004 060--0008 061-0004 061-0008 061-0010 069-0009 069-0024 244-119 029-0088 DESCRIPTION
WIRE HARN CARD AC IN CONN PLUG AMP 2P YELLOW CONN CAP AMP 2P YELLOW CONN PIN AMP CONN SOCKET AMP WIRE HARN NETWORK EXT A CONN CAP AMP MINI 6P WHITE CONN PLUG AMP MINI 6P WHITE WIRE HARN NETWORK EXT B CONN CAP AMP MINI 6P RED CONN PLUG AMP MINI 6P RED CONN PIN AMP MINI (AMP 170360-1) CONN SOCKET AMP MINI (AMP 170362-1)
V-BELT DC FAN MOTOR INSL SPIRAL TUBE ID 26 INSL SPIRAL TUBE ID 212 INSL SPIRAL TUBE ID 225 TIE BELT 85mm BUSH 1.6t TIE BELT 85mm BUSH 1.6¢ CORD CLAMP 215
M SCR PH M4xs0 M SCR PH W/SF M5x10 TMP PRF SCR TH M5x10 M SCR PH BLK M4x10 HEX BLT M8x30 HEX BLT S=30 M10x30 HEX NUT M10 FLT WSHR M4 FLT WSHR M8 SPR WSHR M4 SPR WSHR M8 SPR WSHR M10 FLT WSHR 10.5-28-2 FLT WSHR BLK M4 DOUBLE-FACE TAPE CLOTH 20mmx15m/ROLL M. SCR P-H BLK M4x6
@ ASSY POWER SUPPLY & AMP (KR-—40003) (D-1/2)
z0> » dea | oe ee
OE)
@ ASSY POWER SUPPLY & AMP (KR—40003) (D-2/2)
ITEM No.
Nanak weNE
lll PART No.
KR-—4003 RH-4002 560-5091 560-5092 839-0035 421-6512 SGB-3760-1 211-0044 211-0080 211-0115 211-0116 211-0117 211-0081 211-0082 211-0073 211-0103 211-0043 212-5034 212-5067 211-0005 211-0041 211-0042 212-5076
150-0173 117-0184 514-0064 514-0032 514-0036 514-0040 514-0035 601-0769 601-0460 280-5008 280-0419 481-0157 150-0265 150-0173 000-0514 000-516-FS 005-3113 005-3520 061-0005 006-3113 DESCRIPTION
WOODEN BASE GRIP PWR XFMR 90~240V 100V 2A 11V 5A PWR XFMR 90~240V 60, 70. 80V. 5.5A 18V 1.5A 9.5V 1A PWR AMP BD STICKER FUSE INSTR WIRE HARN PWR SUPPLY & AMP CONN CAP AMP 2P WHITE CONN CAP AMP 2P BROWN CONN CAP AMP 2P RED CONN CAP AMP 2P ORANGE CONN CAP AMP 2P YELLOW CONN CAP AMP 3P BROWN CONN CAP AMP 4P BROWN CONN PLUG AMP 4P WHITE CONN PLUG AMP 6P RED CONN PLUG AMP 2P WHITE CONN FEM 6P MOLEX CONN FEM 8P MOLEX CONN CLALP LOCK (MOLEX 08-05-0105) CONN PIN AMP (AMP 350687~1) CONN SOCKET AMP (AMP 350536-1) CONN FEM 4P MOLEX
CAP E 4700#F 50V TERMINAL PLATE IL 4P FUSE HOLDER 2P W/COVER FUSE 2A 6.4x30mm FUSE 3A 6.4x30mm FUSE 4A 6.4x30mm FUSE 10A 6,.4x30mm STAPLE MAX #3 PLASTIC TIE BELT CORD CLAMP 215 HARN LUG DIODE BRIDGE S5VB20 CAP E 22000MF 25V C-TYPE CAP E 4700MF 50V M SCR PH M5x14 M SCR PH W/F & S M5x16 W SCR RH 3.1x13 W SCR RH 3,5x20 S WASHER M5 W SCR FH 3.1x13
ASSY SW RGLTR & DRIVE BD (KR—41001) (D-1/1)
ITEM No, PART No. DESCRIPTION
| 1 | KR-4101 | WOODEN. BASE |
| 2 | KR~4103 | BRACKET |
| 3 | 834-6035, | DRIVE BD OUT RUN |
| 4 | SGB-3760—28 | WIRE HARN SW RGLTR |
211-0043 CONN PLUG AMP 2P WHITE 211-0094 CONN PLUG AMP 2P RED 211-0086 CONN PLUG AMP 3P BROWN 211-0123 CONN CAP AMP 4P YELLOW 211-5101 CONN FEM 10P AMP 211-5046 CONN FEM 34P AMP 211-0041 CONN PIN AMP (AMP 350687-1) 211-0042 CONN SOCKET AMP (AMP 350536~1) 211-5047 CONTACT (AMP 170435-4)
| 5 | 600-5303 | ASSY FEM & FC 26P |
| 6 | 600-5304 | ASSY WIRE HARN MIC 5P |
| 101 | 400-5055 | SW RGLTR 90~240~ 5V 10A |
| 102 | 117-5131 | TERMINAL PLATE 5P |
| 103 | 280-0419 | HARN LUG |
| 104 | 601-0460 | PLASTIC TIE BELT 85mm |
| 105 | 280-5015 | FASTON RCPT 187 |
| 106 | 211-0167 | TERM LUG RND ID 5 |
| 107 | 270-5016 | FERRITE SLEEVE CORE |
| 201 | 005-3520 | W SCR RH 3.5x20 |
| 202 | 005--3513-F | W SCR RH W/F 3.5x13 |
| 203 | 010-0310-F | S-TITE SCR PH W/F M3x10 |
SEGA ENTERPRISES, LTD. No. 2-12, Haneda 1 —chome Ohta-ku, Tokyo 144, Japan Tel. : (03) 743 — 7438 OFAX: (03) 743 — 5539
OTLX : J22357 SEGASTAR
© SEGA 1986
Printed in Japan ce eR ete
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.