CATHODE RAY TOMES

Cyber Cycles Standard

Cyber Cycles (World, CB2 Ver.C) (Namco, 1995) · Document · 37 pages · 7 sections · original scan

Page 1

8€000S06 “ON Hed “X14SIO4SY¥d GAMOT1104 SHV TWANVW SIHL NI LNO LAS STIVLAG SHL LVHL SAILVYSdWI SI LI GNV ‘SAWIL TV iv ALBZAVS YAWOLSND NIVLNIVW OL HOLVHAdO SHL SO ALIMIGISNOdS3Y AHL SI L] jenueyy sioyesodCQ SA TOAD YAEAD

Page 2

SAFETY WARNING

In Order to Use This Machine Safely

In order to use this machine safely, be sure to read this Operators Manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Also, carefully read section 3, “Precautions”.

Warnings for Operation

( NOTE:

NOTE:
NOTE:
NOTE: Only operate this machine after checking that it has been installed correctly Y and in accordance with the manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There is a warning sticker that the player must be able to reach the grey matting of the cycle base with their feet, however if the operator feels that a customer playing the game is in any danger, he should warn the customer accordingly. The warning sticker must always be kept in good condition and replaced if worn so that the customer can read it clearly. If there is an error or problem with this machine, operation must be stopped immediately. )

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting

DANGER:
DANGER:
DANGER:
DANGER:
NOTE: Namco Ltd. bears absolutely no responsibility for accidents or injuries )

resulting from unauthorized changes to the machine. Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel carry out maintenance or turn the power ON to this machine. The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is a possibility of burns or electric shock. Be careful not to touch these areas. In order to avoid injuries due to mis-operation, be sure that the voltage of the power supply is within the prescribed limits. Also to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug. Do not turn the main power switch ON until the machine has been installed correctly. )

Page 3
  • SPECIFICATIONS

POWER SUPPLY :-

MONITOR :-

COIN ACCEPTOR

DIMENSIONS :-

Assembled Monitor Cabinet Tower Bike Assy Header

WEIGHT :-

Assembled Monitor Cabinet Tower Bike Assy Header

ACCESSORIES :- 220/240volts AC

Hantarex 28" Polo with Auto Degauss

Mars CashFlow - 4 Channel

1700(w) x 1970(d) x 2100(h) 800(w) x 750(d) x 1530(h) ea. 500(w) x 710(d) x 1800(h) 910(w) x 1370(d) x 930(h) ea. 1450(w) x 240(d) x 500(h)

425kg 95kg ea. 80kg 65kg ea 25kg

Keys: (Cash Door) .. (Coin Door) ... (Service Door) .

Number Decal Set 1-4 ........ccceeeeeeee 2

IEC Mains Lead ........ccsssseesesseseeeeee 1

LINK Cable cxcsscsesenesuransaatsnarensssonconaes 1

Operators Manual ...........ccccesesseeeeseeee 1

Monitor Manual ............:ccsesseseseseseeeeeee 1

Cashflow Datta co. ccccisssissanceisacssseecsssenssaave 1

M8x40 Security Screw - SUS .... M8x20 Security Screw - SUS M8x16 Security Screw - SUS M8 Flat Washer - SUS.... M8 Spring Washer - SUS

M5 Security Wrench M6 Security Wrench M8 Security wrench .....

Page 4
  • MAJOR COMPONENTS

Header Assy

Monitor Assy

Handlebar Assy System 22 CPU Bike Assy

Page 5
  • PRECAUTIONS

Be sure to read this section carefully.

3-1 Notes on Operation

(— >)

NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the manual.
NOTE: Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There is a warning sticker that the player must be able to reach the grey matting of the bike base with their feet, however if the operator feels that a customer playing the game is in any danger, he should warn the customer accordingly.
NOTE: The warning sticker must always be kept in good condition and replaced if worn so that the customer can read it clearly.
NOTE: Ensure customers do not get hurt by leaning or climbing on the cycles. Be especially careful in the case of young children.
NOTE: If there is an error or problem with this machine, operation must be LL stopped immediately. )

Parts of this machine lean to the left and right during game play. In order to maintain the customer's safety, the operator should strictly follow the appropriate precautions.

3-2 Cautions When Transporting.

a. Do not subject the game to physical shock when transporting or moving it.

b. Always return the levellers to the UP position before moving the machine, even for short distances.

c. The main cabinets, bike assemblies, coin assy and header assy must be separated before moving or shipping.

d. Take care not to rope any moulded (plastic) parts when transporting.

THIS MACHINE IS NOT DESIGNED TO BE MOVED BY FORK LIFT. DO NOT USE

Page 6

3-3 Cautions When Installing.

1. following places This machine is designed for indoor use only. Do Not install the machine in the

® Outdoors.

io) Direct sunlight, places with excessive humidity or

dust, places where there is water leakage, near airconditioning or heating equipment, places with excessively high or cold temperature.

[ @® Places where it would be in the way of emergency exits or fire extinguishing equipment.

®

If this machine is installed next plenty of space between them. 2. to walls or other machines, ensure that there is

Page 7
NOTE: So that customers are not injured by the movement of the bikes, ensure that the machines are separated from each other by 200mm and from walls or other machines by at least 300mm either side, and 600mm from the rear of the bikes.
NOTE: |n order to gain access to the mains-in connector, ON/OFF switch and link switches, make sure that the rear of the machine is separated from a wall or other machine by a distance of at least 500mm or more.

4m80cm a

30cm 20cm 30cm

3 m70cm

} Vy) iY) AFETY ZONE YZ “yp i } Were VT

Page 8

3-4 Cautions when Handling.

( DANGER The Mains Voltage to this machine must be within the range of *)

220v to 240v AC.

DANGER Be sure that the power is turned OFF when replacing parts and connecting/disconnecting connectors.
DANGER To prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug.
DANGER The monitor and power supply contain areas of very high voltage. Be extremely careful when inspecting or making adjustments.
DANGER When unplugging the game from an electrical outlet, always grasp the plug, not the mains lead. Ne /

NOTES:

. Always return PC Boards to your dealer for repair. Never test the PCB for continuity with a multimeter or similar device. The PCB contains sensitive devices which could be damaged or even destroyed by the internal voltage of such test equipment.

. Adjustments are required after replacing the game PCB, ROM or control pots. Adjustments should be performed as described in section 7-4, "Adjustments when Replacing Parts" (page 25).

. After initial installation or if the number of machines linked together changes, it may be necessary to use the test mode to change the settings and link switch settings. (Refer to section 6-4, "Linking Two Machines" (page 20).

Page 9
  • INSTALLATION
Note:- The monitor cabinets and tower are supplied already assembled. The following instructions are for information only.

4-1 Assembling the Monitor and Tower Assemblies

  • Connect the loom connectors between the tower assembly and the monitor assembly, and place the assemblies together, taking care not to trap any wires.
  • — Fit, finger tight, three M8x20 Security Screws, Spring and Flat washers to connect the tower and monitor base.
  • Fit, finger tight, four M8x20 Security Screws, Spring and Flat washers to connect the monitor cabinet connector cover to the tower.
  • Tighten fully all the Security Screws. (7off)
  • Repeat above for the other monitor cabinet.

Monitor Assy : ee .

+

Connector Cover

Page 10

4-2 Connecting the Bike Assemblies to the Cabinets

1.

6.

Ti Connect the connectors between the bike assembly and cabinet.

Place the bike assembly onto the support bracket and push the bike against the cabinet taking care not to trap any wires.

Fit, finger tight, the 4off M8x20 security screws, spring washers and flat washers, securing the Bike Assy to the Monitor Base.

Fit, finger tight, the 20ff M8x20 security screws, spring washers and flat washers, securing the Bike assy to the support bracket.

Tighten fully all the security screws. (6off) SUPPORT BRACKET « CONNECTOR

\ 8x40 SECURITY SCREW

\_M8x20 SECURITY SCREW.

Fit the bike number decal to the rear of either side of the bike.

Remove the shipping bolts (M8x75) from either side of the bike.

Note:- Retain the shipping bolts in a secure place for re-fitting if the machine is transported.

Shipping Bolt (x2)

Page 11

4-3 Fitting the Header Assembly

The Header Assembly is heavy (approx. 25kg), with a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)

  • Place the Header Assembly on to the tower and pass the connectors in to the tower, slide the header back ensuring that the rear bracket engages fully in to the retaining brackets.

Rear Bracket

Retaining Bracket

  • Fit the 80ff M8x16 Security Screws, Spring and Flat washers to retain the Header Assembly to the Tower.
  • | Connect the connectors inside the monitor cabinet.
NOTE:-

When the machine is fully assembled and in its final position, lower the 14 level adjusters, (4 on each monitor cabinet, 2 on the tower and 2 on each bike assy), with a spanner so that all castors are raised from the floor, and the machine is level.

Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Lock nut Level adjuster

Page 12

How to Play

This game is linkable so players can compete against each other on the same track, or compete against computer bikes when playing alone. Two machines can be linked together allowing up to four players to compete against each other.

The Header Assembly displays the position of each rider and also the leading rider.

Speed is controlled by use of the throttle and brake, and steering is controlled by leaning the bike left or right.

After the insertion of a coin/s, credit is established to a bike position with the use of the respective ‘Credit Available’ button. Pressing the flashing ‘View Change’ button, located on the handle bar assembly, will display the Course Select Screen. There are two courses available, “GREEN HILL” is a practise course for beginners and “NEO YOKOHAMA’ is an intermediate and advanced course. In a linked game the course is decided by the majority.

Next select a bike. Each player can select one of three bikes:-

“ANTHIAS”, for beginners. It corners easily, and its top speed is reduced a little.

“NVR750R’, for intermediate. This bike has good cornering balance, and its top speed is normal.

“WILD HOG” for advanced. By controlling the special drift, it can cover the course faster than any of the other bikes, but is more difficult to control.

The first player to enter “Bike Select” is also able to select, by using the throttle, the music during the game. The title is displayed in the lower left of the screen.

Players can join in a linked game during the link time countdown. This time can be adjusted in the ‘Game Options’ mode. If a linked game is in progress but a bike position is available, a player can use this position as a solo game.

When a player completes the specified number of laps in the given time, they complete the game. If the countdown timer reaches 00 before completing the specified number of laps the game is over. At the end of the game, the players ranking, fastest lap time and total time are displayed.

If a best time is beaten the end of the race will be shown and the player can enter their initials by leaning the bike to select the letters and pressing ‘View Change’ to enter them.

With this game it is possible to change the players viewpoint of the game. Each time the ‘View Change’ button is pressed the view changes between : “Pillion View”, “Rider’s View”, and “Behind View”.

Page 13
  • ADJUSTMENTS

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the right hand cabinet.

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" (page 12))

COIN COUNTER °

°

TEST LEFT PLAYER O O

SERVICE ce) RIGHT PLAYER O O

TEST SERVICE ‘e)

Service Bracket

Page 14

6-3 Test Mode

  • Open the coin door and slide the test switch "ON". The menu screen will be displayed on the monitor.
  • Select the test required by leaning the bike left or right. The selected test will ‘blink’.
  • Enter the selected test by pressing the 'View Change' push button. Select "EXIT" to return the "Menu Screen".
  • After testing is completed, ensure that the test switch is returned to the "OFF" position to return to normal game mode.

The Test Switch must always be in the "OFF" position for normal game mode.

X MENU

COIN OPTIONS

GAME OPTIONS

VO TEST

SOUND TEST

MONITOR TEST

ADS TEST

OTHERS

BANK : CHOOSE VIEW SW _ : ENTER Sets the price of play (See 6-3-1)

Sets the game options (See 6-3-2)

Used for testing switches and controls (See 6-3-3)

Used for testing sound and setting volumes (See 6-3-4)

Used for adjusting the monitor

Displays accumulated game data

Used for testing the PC Boards and for initializing all of the settings

Page 15

6-3-1 Coin Options

  • Select item (1) "COIN OPTIONS" on the menu screen to set the game cost and related settings.
  • Lean the bike left or right to select the required item then press View Change.
  • Use the Brake to adjust the settings UP or the Throttle to adjust the settings DOWN, press View Change to store the new settings.
  • Select "EXIT" to return to the menu screen. COIN OPTIONS [ DEFAULT IN GREEN ]

GAME COST 1 COIN 1 CREDIT

FREE PLAY OFF

EXIT

BANK :CHOOSE BRAKE VIEW SW :ENTER Ne THROTTLE :CHANGE- :CHANGE+

Note :- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

TEM CONTENTS FACTORY SET

  • Game Cost Coins required for 1 credit - - - - - - settable 1-9 1
  • Free Play Yes/No NO
Page 16

6-3-2 Game Options

  • Select item (2) "GAME OPTIONS" on the menu screen to set the game options and related settings.
  • Lean the bike left or right to select the required item then press 'View Change".
  • Use the Brake to adjust the settings UP or the Throttle to adjust the settings DOWN. Standard settings are displayed in green.
  • Select "EXIT" and press 'View Change' to return to the menu screen.

(— >) GAME OPTIONS [ DEFAULT IN GREEN ]

GAME DIFFICULTY B GAME LAPS GREEN HILL 3 NEO YOKOHAMA 2 ENTRY TIME B ID NUMBER SEAT COLOUR LANGUAGE SOUND IN ATTRACT HI SCORE INITIALIZE EXIT BANK :CHOOSE BRAKE :CHANGE+ VIEW SW :ENTER THROTTLE :CHANGE- LINK ON 1

a /

NOTES »

The game difficulty and number of laps and entry time must be set the same on all positions that are linked.

The ID number of the bike furthest left (when facing the front of the machine) should be set to 1, and the other bikes set to 2, 3, or 4in order from left to right. The ID number of the farthest right position should equal the number of bikes linked.

Settings other than those described will cause the machine to operate incorrectly. S

Page 17

Tem DESCRIPTION FACTORY

SET

  • Game Difficulty | A (easy) to C (hard) B
(b) Green HilNumber of laps for Green Hill course - - - set 2 - 53

(©) Neo Yokohama | Number of laps for Neo Yokohama course - - - set 1 - 5 2

(d) Entry TimeA (longest) to C (shortest)B
  • ID Number Sets bike identity for linked positions. Set so that no linked bikes have the same number

Machine Linked - Display will show - LINK ON + number of linked units

. Faulty Link Cable - Display will show - LINK OFF ( Displays Link pl Only one machine - Display will show - ON 4

Faulty Link PCB - Display will show - NG

  • Seat Colour Sets the bike colour. Set to match the colour of bike in use
(h) LanguageJapanese, English, NoneEnglish
() Sound in Attract| On/OffOn

() Hi Score tritialize | On/Off oft

6-3-3 I/O Test

  • Select item (3) "I/O Test" on the menu screen to test the switches or lamps.
  • Lean the bike left or right to select the required item then press View Change.
  • Select "EXIT" and press 'View Change' to return to the menu screen.

ye VO TEST )

DIP 4 12845678 vesesssssssseseseeeeefeece (a)

SWITCH TEST eccccccccctesssseceefhece (b) MOTOR TEST (c) LAMP TEST ) EXIT

BANK :CHOOSE VIEW SW :ENTER Ne S

  • Shows condition of DIP SW 4 on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)

Switch 1 if ON will force the PCB in to Test Mode.

Switch 8 if ON will freeze the picture on the monitor.

  • Shows if the game is linked.
Page 18

6-3-3-1

1.

6-3-3-2

6-3-3-3

1. Switch Test

Select Switch Test from the 'I/O Test' menu. The following screen will appear on the monitor.

( SWITCH TEST )

TEST SwON..(a)

COIN SW ON b)

SERVICE SWON...(c)
BANK00 CENTRE .(a)

THROTTLE 00 e)

BRAKE00...(f)
VIEW-SWONeeseseseefeee (g)

4, BRAKE STHEOTILE: EXIT The word 'ON' will appear next to items a, b, c, and g each time the respective switch is operated. When the bike is pushed left, 'CENTRE' will go off and 'OK' appear just before it reaches the extreme left, '00' will decrease. When the bike is pushed right, ‘CENTRE ' will go off and 'OK' appear just before it reaches the extreme right, '00' will increase. When the THROTTLE or BRAKE are operated, 'OK' will appear just before they are fully on, and '00' will increase.

Operate the brake and throttle together to exit and return to the 'I/O Test' menu screen.

Motor Test

This test is not used on this machine

Lamp Test

Select Lamp Test from the “I/O Test” menu. The following screen will appear on the monitor

( LAMP TEST )

ALL LAMPS RED YELLOW BLUE

GREEN VIEW-SW

VIEW-SW: EXIT Ne

Page 19
  • The lamps will automatically illuminate in turn as indicated on the screen.
  • Press ‘View Change’ to return to the “I/O Test” menu screen.

6-3-4 Sound Test

  • Select item (4) "Sound Test" on the menu screen to test the sound and speakers.
  • The following screen will appear on the monitor.

C >) SOUND TEST [ DEFAULT IN GREEN ]

VOLUME FRONT LEFT SP. 55 FRONT RIGHT SP. 55 TANK SP. 50 REQUEST SONG No. 000

MESSAGE ETC. wenseeenccccneponne (e) EXIT

BANK :CHOOSE BRAKE :CHANGE+ VIEW SW :ENT/ON,OFF THROTTLE :CHANGE-

Ne wy,

  • Select the required item by leaning the bike left or right. The selected item will ‘blink’.
  • Operating the brake will increase the value setting and operating the throttle will decrease the value setting. Standard values are displayed in green.
  • Press ‘View Change’ to start or stop a Reqest Song No. sound. (Request Song No. 3 will generate a stereo sound test.
  • Select “EXIT” and press ‘View Change’ to return to the menu screen.

Item Description Factory Set

aSet left speaker volume.00 Quietest - 63 Loudest32
bSet right speaker volume=- -- ---00 Quietest - 63 Loudest32
cSet bike tank speaker volume —- - - - - -00 Quietest - 63 Loudest32
dSelect sound for testing. Each number will produce a different sound. 000a

will generate a stereo test.

eDisplays song nameo--
Page 20

6-3-5 Monitor Test

  • Select item (5) “Monitor Test” on the menu screen to set up and adjust the monitor.
  • Onentering monitor test, the following screen will appear on the monitor.

(— >) MONITOR

GRADATION PATTERN CROSSHATCH GREEN CROSSHATCH WHITE WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJECTOR) FULL WHITE EXIT

BANK :CHOOSE VIEW-SW :ENTER S

  • Lean the bike to select a test and press ‘View Change’ to enter the test and to return to “Monitor Menu” from a test.

6-3-6 ADS Data

  • Select item (5) "ADS Data" on the menu screen to view machine history details.
  • The following screen will appear on the monitor.

4 ADS )

POWER ON 00'00"00 PLAY TIME 00'00"00 PLAY TIME AVE —_00'00"00 PLAY NUMBER 0000 ests

COURSE-VIEW —hacesessesedeeeeee COURSE-BIKE “ COURSE -LINK COURSE-C. P. COURSE-P.T. SSSSs

INITIALIZE eeesssedheceee (i) EXIT

BANK :CHOOSE i VIEW-SW :ENTER

Page 21

Item Description

  • Power On Total time in hours, minutes, seconds machine has been switched on.
  • Play Time Total time in hours, minutes, seconds that machine has been in play.
  • Play Time Ave Average time of game duration.
  • Play Number Total game plays.
  • Course-View Time for each view.
  • Course-Bike Number of times a bike has been selected.
  • Course-Link Number of linked games played.
  • Course-C.P. Position on the course at game over.
  • Course-P.T. Total time each course has been played.

() hritialize Reset all data.

6-3-7 Others

  • Select item (6) "Others" on the menu screen.
  • On entering 'Others' the following screen will appear on the monitor.

( OTHERS >)

AUTO SETTING heeds (a)

BACK UP MEMORY INITIALIZE ......J..... (b)

PCBTEST aececdeceecee (c)

EXIT

BANK :CHOOSE | VIEW-SW ‘ENTER )

  • Auto Setting Will adjust all inked units to match automatically.
  • Back Up Memory Initialize | Reset all ADS data
  • PCB Test For testing the Game PCB
  • _ If the game is linked, this option allows all linked positions to be set from position No. 1 bike. If all game and coin options shown on No. 1 screen are correct, select transmit, then push View Switch. All positions will automatically update to the displayed options and ID No. All screens will display the Auto Setting screen. Set each bike colour from each Auto Setting screen.
Note: Any game in play will be lost during Auto Setting transmit.
Page 22

6-4 Linking Two Machines.

Up to two machines (4 bikes) can be linked together. The machines should be linked as described below.

  • Ensure that the power is “OFF”.
  • Loosen the two screws (M5x12) on the back of the right monitor cabinet, and remove the connector cover.

Connector cover

screw (M5x12)

  • Set the link switches to “ON” , “EXT”, and “ON”. (See Diag.) Link switches
  • Use the supplied link cable and connect the machines between “IN” and “OUT” sockets (See Diag.)

[Examples of Linked Machines]

  • 2Machines © oO © oO (2 Seats) IN__OUT IN__OUT
  • Turn the power to each machine “ON”, and set the PCB ID using the test mode. (Refer to section 6-3-7, “Others” 'Auto Setting' (page 19))
Note: Settings other than those described will cause the machine to operate incorrectly.
Page 23

6-4-1 Setting the Link Switches

The link switches are used to set the connection between bikes and machines.

Link Cover

  • Slacken two screws (M5x12) and remove the link cover.

2). Setting only one machine. (2 Bikes) Q Q @ i" Set the link switches to “ON”, “INT”, and | S2Is @3

“ON”.te(@_Jis@

stai_]t ©# )

Note:Do not use a link cable.OoOo@

fe} fe) i)

  • Setting two or more machines. (4 Bikes) isa é 63
Set the link switches to “ON”, “EXT”, and— é®

ean eam 1 O=

‘ON’.5®@

fo} fe}

  • The link procedure is now complete.
  • Setting for faulty PCB.

If the game PCB of only one side is faulty, set the link switch on that side only to “OFF”

Page 24
  • MAINTENANCE
DANGER: In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.
DANGER: Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions.

7-1 Replacing the Fluorescent Tube, Position, and Leading Driver Lamps

  • Remove the three security screws (M5x12), and remove the plexi upper retaining bracket.
  • Remove the three security screws (M5x12), and remove the plexi lower retaining bracket.
  • Remove the header plexi.
  • Unscrew the defective position lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it.

7-2 Replacing the Signal Lamps

  • After removing the front Plexi as above remove five security screws (M5x12), and remove the signal plexi L or R.
  • Unscrew the defective lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it.

Sigal) t Upper Rettig at

Mbx12 Security Screw J

MSx12 Security Screw

a) im) - 'Signal Plexi (R) MSe12 Seturiy Screw Lower Retaining Brkt Leading Driver Lamp

Position Lamp

Page 25

7-3 Handle Bar Assembly

Remove four M5X12 security screws, and remove handle bar assembly cover to gain access to the throttle and brake controls.

NOTE:- The game must be re-initialized whenever the PCB, ROMS, Throttle, Brake or Steering controls are replaced. (See 7-4 "Adjustments when Replacing Parts")

7-3-4

1)

7-3-2

1) Replacing the Throttle Control Pot

Slacken the grub screw M3X5 securing the control pot shaft to the drive gear, and remove the gear.

Replace the control pot ensuring that the the pot is replaced in the same position, and the wires are replaced to the correct terminals.

Turn the control pot shaft until the flat is vertical and to the right, when looking at the shaft. Replace the drive gear ensuring that the control pot shaft does not turn and the grub screw in the drive gear is on the flat of the shaft

Re-tighten the grub screw M3x5

Replacing the Brake Control Pot

Slacken the grub screw M3X5 securing the control pot shaft to the brake assembly.

Replace the control pot ensuring that the pot is fitted in the same GRUB SCREW M3x5 BRAKE CONTROL POT

GRUB SCREW M3x5.

FLAT ON SHAFT

CONTROL POT SHAFT POT BRACKET

CONTROL POT

DRIVE GEAR

GRUB SCREW M3x5

position, and the wires are replaced to the correct terminals.

When replacing the control pot, ensure that tl line with the grub screw.

Re-tighten the grub screw M3x5. he flat on the control shaft is in

Page 26

7-3-3 Replacing the Steering Control Pot

  • Remove three security screws (M5X16) and four security screws (M5x12) from the right hand bike vac-form, and remove the vac-form.
  • Slacken the grub screw (M4x5) to release the control pot shaft.
  • Replace the control pot, ensuring that the pot is replaced in the same position and the wires are fitted to the correct terminals.
  • Re-tighten the grub screw (M4x5), ensuring that it engages the flat of the control pot shaft.
  • Refit the bike vac-form, and the security screws (M5x12) (M5x16).

SECURITY SCREW (M5x16) SECURITY SCREW (M5x12)

SECURITY SCREW (M5x16)

MOUNTING BRACKET

EARTH TAG O O

GRUB SCREW Maxé_/ A top view

GRUB SCREW Max5

CONTROL POT

A SIDE VIEW

Page 27

7-4 Adjustments When Replacing Parts (Initialization)

The following adjustments must always be carried out after replacing the Game PCB, ROMS, or Throttle, Brake, and Steering Control Pots. The game will not operate correctly if these adjustments are not made.

1.

4.

5. Ensure that the Throttle and Brake are fully released and the bike is in its central upright position.

Turn the Test switch on while pressing the Service switch.

Adjustment is complete when the screen displays ‘Initialize Completed’.

Operate the Brake and Throttle together to return to the “Menu Screen”.

Turn the Test switch OFF to return to normal game mode.

Note:- _ If the ‘View Change’ button is flashing during standby mode, there is a problem with one of the control pots (Throttle, Brake, or Bank) not being at zero. Enter ‘Switch Test’ (See 6-3-3-1 ‘Switch Test’ page 16) to determine which pot is not at zero and either replace if faulty or reinitialize.
Page 28
  • PARTS
Page 29

ITEM DESCRIPTION PART No.

1| MONITOR CABINET45000521
2| MONITOR SUPPORT PIPE AND BRACKET45000520
3| MONITOR PLINTH45000517
4| MONITOR CABINET BACK PANEL45000522
5| LOUDSPEAKER GRILLE45000528

LOUDSPEAKER CABINET - LHS 37100069

*TOUDSPEAKER CABINET. RHS37100070
7| 28" HANTAREX ‘POLO’ MONITOR with REMOTE84000012

8 | MONITOR PLINTH JOINT BRACKET - UPPER 45000519 9 | MONITOR PLINTH JOINT BRACKET - LOWER 45000518 MONITOR SIDE VAC-FORM RHS - RED 45000526

tg| MONITOR SIDE VAC-FORM RHS - YELLOW45000527

MONITOR SIDE VAC-FORM RHS - BLUE 45000528 MONITOR SIDE VAC-FORM RHS - BLACK 45000529 MONITOR SIDE VAC-FORM LHS - RED 45000530

11| MONITOR SIDE VAC-FORM LHS - YELLOW45000531

MONITOR SIDE VAC-FORM LHS - BLUE 45000532 MONITOR SIDE VAC-FORM LHS - BLACK 45000533

12| MONITOR VAC-FORM45000524
13| SWIVEL CASTOR 75mm59000005
14| ADJUSTABLE FOOT M16x7525000009
15DOME PLUG - 45mm39000809

18 | SHORTY BUSHING - 45mm 39000054 MONITOR VAC-FORM DECAL - BLACK 40000248

1g| MONITOR VAC-FORM DECAL - RED40000249

16 | MONITOR VAC-FORM DECAL - YELLOW 40000250 MONITOR VAC-FORM DECAL - BLUE 40000251

Page 30

ITEM DESCRIPTION PART No

1FRONT ACRYLIC RETAINING BRACKET45000535
2FRONT ACRYLIC30000039
3FLUORESCENT TUBE 18" 15w64500009
4CHOKE 240v 15w63300000
5STARTER63000000
6COIN TOWER SAFETY DECAL40000254
7‘CREDIT AVAILABLE WHEN LIT’ PUSHBUTTON ASSY60200215
8ADJUSTABLE FOOT M16x75mm25000009
9SWIVEL CASTOR 75mm59000005

Tem DESCRIPTION PART No.

1| PCB SERVICE DOOR45000547
2| PCB ASSY- CYBER CYCLE - VistXCYB-PCB

‘SMPSU 5vi30A 125A, ‘83000004

  • FUSE 2A SLO-BLO 63500506
  • FUSE 3A SLO-BLO 63500547

11 FUSE 2A QB 63500504

‘SCHAFFNER MAINS INPUT ASSY 66000016

4| 20mm FUSE 5A OB63500601

SCHAFFNER BOOT 66000017

LINK PCB ASSY XAD-LINKPCB

LINK COVER BRACKET 45000550

Page 31

ITEM DESCRIPTION PART No.

1RACE START VAC-FORM - LHS45000452
2TOP ACRYLIC RETAINING BRACKET45000537
33ft FLOURESCENT TUBE64500013
4RACE START VAC-FORM - RHS45000453
5£14 25watt GOLF BALL LAMP64000084
7TOP ACRYLIC30000040
8E14 25watt REAR SILVERWED LAMP64000083
9SHORTY BUSHING - 50mm39000051
BIM5x16 SUS SECURITY BUTTON HEAD SCREW26300032
Page 32

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 33

TreM DESCRIPTION PART No

1[evoue BASE FRAME4000888

2 _ | BEARNG MOUNTING ASSEMBLY 000882 @ | ROGKERPLATE 4000894

@_| ROTARY MOULDNG SUPPORT BRAGKET - LHS4000818

6 _ | ROTARY NOULDNG SUPPORT BRACKET - FHS 000816

6[ RosTa BRACKET4000897

7 _| CoNNEGTOR GovER 400881 @ | EVArLoonMaT- Grey 000889 @ _| PoreNnOMETER BRACKET 5000898 10 | space 45000898

11[spacer5000886
v2_|sPacen5000886

ROTARY NOULDNG - BLACK 4000501

ROTARY MOULDNG - RED aso00802

*ROTARY MOULDING - YELLOW45000503

ROTARY MOULDING BLUE 000808

LOWER VAC-FORM FHS - BLACK ‘000805

LOWER VAC-FORM FHS -RED ‘000806

*LOWER VAC-FORM RHS - YELLOW45000507

LOWER VAG-FORI FS - BLUE ~s000808

LOWER VAC-FORM LHS - BLACK 000809

LOWER VAC-FORM LHS - RED 4000610

*LOWER VAC-FORM LHS - YELLOW45000511

LOWER VAC-FORM LHS - BLUE asoo0612

14_|#2 2ow SPEAKERsan00006
te_|SEAT VacFonmaso00618
17_|END OF STROKE BUMPERses006s4
1e_|PLLOW BEARNG-FYH/UPG 207ees00688
10| ROSTA SPRING -DA-G27 x 100XxEn00.261~
20_|SWIVEL CASTOR ésmmse000002
at_|ADJUSTABLE FOOT tos8800078
22_|naMco Loco ROTARY MOULONG0000238
23_|nawco Loco vac-FoM0000236

TAR INTAKE DECAL FRONT LS ooo

“AIR INTAKE DECAL FRONT - RHS-40000242

AR INTAKE DECAL SDE - LHS 0000248

*AIR INTAKE DECAL SIDE - RHS40000244
26_|cvBeR GvCLES LOGO VAC FORM000237

REAR DECAL ROTARY MOULDING - LHS ‘40000238

”REAR DECAL ROTARY MOULDING - RHS40000240
28_|chRowE DECAL REAR UNDERSDE0000246

GHROME DEGAL SDE LS 000246

“‘CHROME DECAL SIDE - RHS40000247

co _| sus 400 FLOOR war COVER BRACKET 40000490

ot_|FILLER GAP vac-Fomu61700828
e4_|CYCLE BASE SAFETY COVER. REAR0000282

os _| VOLE BASE SAFETY COVER LHSIRS 0000288

e_|PoreNTioweTeRxo0e0002s
Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

ITEM DESCRIPTION

1 HANDLE BASE

2 GRIP SHAFT (A)

3 GRIP SHAFT (B)

4 THROTTLE STOPPER

5 THROTTLE SPRING

6 WASHER PLATE

7 THROTTLE GEAR

8 BRAKE PIN

9 BRAKE STOPPER

10 STOPPER ROD

an UPPER BRAKE PLATE

12 BRAKE SPRING

13 BRAKE CONTROL POT BRACKET

14 SLIDE PLATE

15 HANDLE COVER

16 DECAL SET

17 RUBBER GRIP

18 SPRING SPACER

19 GRIP SHAFT GEAR

20 FLANGE BUSHING - LFF 2010

val FLANGE BUSHING - LFF 0705

22 FLANGE BUSHING - LFF 1015,

23 FLANGE BUSHING - 80B 2025

24 THROTTLE SPACER

25 BRAKE LEVER

26 BRAKE BASE

27 BRAKE SPACER

28 THROTTLE PIN

29 BRAKE WASHER

30 PUSHBUTTON ASSY

31 POTENTIOMETER

32 ‘C’ CLIP

Page 36

9.SCHEMATIC

FLUORESCENT ASSY TH FLUORESCENT ASSY ae

oe r sevice Ue SERVICE BRKT | = \ oe 1 \

aa Ir SS ver oS tere ome cashriaw ZT METER SB coven

MARS CASHFLOW 1 i it cue H TELCO LAE [EADER LST. eau a0 TNEUT TEL

LEADER CAVEBREEN LAE12

POSTTDN 4 Lie] +

CONTFLUO LaTet
POST 3 LAE]postion 1 LaeTFL

POSITION 2 LAP] a POLL Las ELLE POSTToN = Lane POSTON 3 CaNeL HT PAST HOH ¢- AMELIE

: TT SREY GRY /BLKD a nae 2TH lena ee eDate Ponca eT eee BNC Ean sia pee eo SS eenvact ta a ee poe Dae te a : 313 ean oma — Pere caver ETS uC a ig rane Tay ta ae RSE ST ee SUPEREE Sy [te 8 GRRE. TL SERVICES TET eal FEI

PLAYER 1

WITCH MODE 17) TOWER SUPPLY

FILTER r

r

24dv AC MAINS. IN cREEN/YELLOW cen TeLe:

NERC BL ERE RED a

RING (D> INGE BLU ERS RED [ae

SCREEN.

CYBER CYCLE

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.