CATHODE RAY TOMES

Indy 500

INDY 500 Twin (Revision A, Newer) (Sega, 1995) · Manual · 84 pages · 58 sections · original scan

Page 1

2ND PRINTING ~ JANUARY ‘96

~ DELUXE

OWNER'S MANUAL

SEGA ENTERPRISES, INC. (USA)

MANUAL NO. 4201-6194-01

Page 2

—\

COPYRIGHT NOTICE

This SEGA product has a copyright notice as follows: © 1996 Sega Enterprises, Inc. (U.S.A.) All rights reserved.

This signifies that this work was disclosed in 1995 and is the property of SEGA ENTERPRISES, INC. (U.S.A.)

Every effort has been made to ensure that this manual is accurate. Sega Enterprises, Inc. (U.S.A.) is not liable for any printing or clerical errors.

Specifications noted herein are subject to change without notice.

Page 3

TABLE OF CONTENTS

ON MOOhwNho

10,

Te

12. 13.

14, 15. 16. 7.

18. 19,

  • PARTS LIST...
  • WIRING DIAG!
  • VIRTUA COP 2 DEI + PRODUCT SEALS AND SAFETY CERTIFICATION. + HANDLING PRECAUTIONS ............. ccc cee cere « INSTALLATION LOCATION PRECAUTIONS . « SPECIFICATIONS. .........0020.000%
  • INSTALLATION ITEMS . PRECAUTIONS TO BE HEEDED WHEN ASSEMBLING AND

« HOW TO PLAY .. 0... cece ee eseeneeaeeenes . EXPLANATION OF TEST AND DATA DISPLAY ..

}» CONTROL PANEL ...... eee s eee nee eee INTRODUCTION OF THE OWNER’S MANUAL.

MOVING THE MACHINE 20... cccccseeeteneesetneeeseenenenee

8-1 SWITCH UNIT... . secs ee eee ee eee 8-2 TEST MODE..... 8-3 MEMORY TEST. 8-4 1.G.P TEST.. 8-5 INPUT TEST.. 8-6 OUTPUT TEST. 8-7 SOUND TEST.... 8-8 C.R.T. TEST....... 8-9 GAME ASSIGNMENTS... 8-10 COIN ASSIGNMENT... 8-11 VOLUME SETTING. . 8-12 BOOKKFEPING......... 8-13 BACKUP DATA CLEAR

9-1 REMOVING THE CONTROL PANEL........ 9~2 ADJUSTING AND REPLACING THE VOLUME 9-3 GREASING SHIFT LEVER ......ccceee cece eeeee 10-1 REMOVING THE SHIFT LEVER... 10-2 SWITCH REPLACEMENT........ 10-3 GREASING............

Ti-1 ADJUSTING AND REPLACING THE VOLUME. . 11-2 GREASING........ 00.22 e eee eceeeee eee COIN SELECTOR ... PROJECTOR .....0sceeeeeeeeeeeeees 13-1 REMOVING THE MONITOR MASK. 13-2 CLEANING THE MONITOR MASK. 13-3 CLEANING THE SCREEN..... 13-4 ADJUSTING THE PROJECTOR. REPLACEMENT OF FLUORESCENT LAMP . PERIODIC CHECK .. TROUBLESHOOT ING GAME BOARD ...... 17-1 REMOVING THE BOARD. . 17~2 COMPOSITION OF GAME BOARD. 17=3 INPUT AND OUTPUT RELATIONS DESIGN RELATED PARTS... COMMUNICATION PLAY ...., 19-1 INSTALLATION PRECAUTIONS. 19-2 CONNECTING THE COMMUN ICATIO! 19-3 SETTING COMMUNICATION PLAY. 19-4 APPLICATION OF STICKER AoOnwos

Page 4

INTRODUCTION OF THE OWNER’S MANUAL

SEGA ENTERPRISES, LTD., supported by its high technology semiconductors, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This Owner’s Manual is intended to provide detailed descriptions together with all the necessary servicing control, spare parts, etc. related to the Indy 500 Deluxe, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, nontechnical personnel should under no circumstances touch the interior system. Should the need arise, contact our Main Office or the closest branch office listed.

SEGA ENTERPRISES, INC, (U.S.A.) Customer Service

41533 Industrial Drive

Fremont, CA 94538 USA Phone (415) 802-1750 FAX: (415) 802-1754

Page 5
  • PRODUCT SEALS AND SAFETY CERTIFICATION

PRODUCT LABELING

To prevent counterfeits and conversions. the following labels are put on all SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of merchandise or by converting, selling or using products or printed circuit boards.

ORIGINAL SEAL LICENSE SEAL

The following seal is put on all machines The following seal is put on all SEGA kits, manufactured by SEGA. such as printed circuit boards,

qi.;
:::3i
47FEa‘7s
ASF EEa(Bese¢
:ORIGINA: SEAI;4LICENSE SEAL
iiner rsoauerep

4 ‘ 4 j ’ 4 4 aro a

SAFETY CERTIFICATION

UL, Listed Amusement Machine: Model SUR-017D-001 FCC Part 15 Subpart J, class A

This equipment has been tested and found to comply with the limits for a Class A digital device in accordance with the specifications in Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 6
  • HANDLING PRECAUTIONS

When installing or inspecting the machine, be aware of the following safety items. Pay attention so that the players can enjoy the game safely.

° Turn the power off before working on the machine. + Do not insert or pull out the plug quickly.

  • Make sure that the power cord and ground wire are not exposed during transportation. Make sure that all ground connections are made safely at the installation position where specified.
  • Do not use any fuse that does not meet the specified rating. + Make complete connections for the IC board and other connections. Insufficient connections are very dangerous. + When cleaning the monitor glass, use a soft cloth. Do not apply chemicals such as benzine or thinner.
  • Sega Enterprises, Inc. (U.S.A.) is not iiable for any damages or injury resulting from use of this equipment in a manner for which it was not designed or intended.
Page 7
  • INSTALLATION LOCATION PRECAUTIONS

The Indy 500 Deluxe is an indoor game machine. Absolutely do not install it outside. Even indoors, to ensure proper usage, avoid installing in any of the places mentioned below. Follow all of the installation instructions and precautions when installing the machine.

LOCATION PRECAUTIONS:

  • Places subject to rain or water leakage, or condensation due to humidity.
  • In the proximity of an indoor swimming pool and/or shower. + Places subject to direct sunlight.
  • — Places subject to heat sources from heating units or hot air.
  • Inthe vicinity of highly inflammable/volatile chemicals or hazardous matter,
  • On sloped surfaces.
  • In the vicinity of anti-disaster facilities such as fire exits and fire extinguishers. + Places subject to any type of violent impact. + Dusty places.

INSTALLATION PRECAUTIONS:

+ Do not insert more than one electrical plug into the power plug socket, + The per unit standard voltage/amperage is 120V/10A. + Use of extension cords should be avoided. If you must use an extension cord, ensure the extension cord is rated at 15A or higher. « For transporting the machine into the iocation’s building, the minimum necessary dimensions of the opening (doors, etc.) are 30 in. (W) x 80 in. (H). + For operation of the machine, the minimum installation dimensions are 26 in. (W) x 40 in. (D). + Due to its size and weight, use at least four (4) peopie to uncrate this game.

Page 8
  • SPECIFICATIONS

71 inches

70 inches ae a

a ee 45 inches

Ficure |: INpy 500 DeLuxe InstaLLation Dimensions

Table 1: Indy 500 Deluxe Specifications TYPE SPECIFICATION

Dimensions, Crated 29 in. (W) x 42 in. (D) x 72 in. (HD 26 in. (W) x 39 in. (D) x 71 in. (H) 375 Ibs.

360 Watts, 3A (MAX.} 39 inch, Projection Monitor, Medium Resolution Dimensions, Installed Weight Power, Current

Monitor Type

Page 9
  • INSTALLATION

The items listed in Table 2 are supplied with the Indy 500 Deluxe and should be included with the machine whenever the machine is moved.

TABLE 2: INSTALLATION ITEMS PART NAME Owner’s Manual - indy 500 Deluxe | _1 Linking Cable (Fiber Optic) In Cash Box

Fuse1Tn Cash Box
Remote Control1In Cash Box
Seat Sticker Set (2- 8}1In Cash Box

Seat Mounting Hardware: In Cash Box Bolts 8 Lock Washers 8

Flat Washers 8 L-Brackets 2 Torx Anti-Tamper Wrenches: In Cash Box MS 1

M8

Keys: Coin Mech Door 2 Strapped to Controls Cash Box Behind Coin Mech Door

Rear Access Panel Behind Coin Mech Door

Page 10
  • PRECAUTIONS TO BE HEEDED WHEN ASSEMBLING AND MOVING THE MACHINE

A

WARNING! @ Perform the assembly work by following the procedure herein stated. Failing to comply with the instructions, for example, inserting the plug into an outlet at the stage not mentioned in this manual can cause an electric shock accident. Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling can cause damage to the machine or malfunctioning to occur. When assembling, be sure to perform the work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When performing the assembly work, follow the procedure sequentially in order-of the 5 items below:

ES CDS f

ASSEMBLING THE CABINET

SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT)

POWER SUPPLY

TURNING THE POWER ON

ASSEMBLY CHECK

Note that the Master Key (an accessory) in addition to the tools such as a plus driver, wrench for M16 Hexagon Bolt and socket wrench is required.
Page 11

ASSEMBLING THE CABINET

Since the Cabinet is moved during the assembly work, be sure to proceed the work in such a place where the floor is level and does not have step-like

CAUTION! differences, with each of the cabinet casters making contact with the

surface.

Hexagon Bolt (black) (4) M8X20, w/ flat & spring washer ® Secure the 2 L type Brackets to the Rear -

Cabinet with 2 Hexagon Bolts (black) for na

each (bracket).

@® Insert the Rear Cabinet's square pipe into the Front Cabinet's square hole. At this time ensure that the pipe is inserted up to the point approximately 10 cm. before the innermost end of the hole. FIG. 6.14

Connector Connect io

® Take out the wiring (3P white connector, 2P black connector) from the Rear Cabinet and connect the wiring to the Front Cabinet's Connector Panel, and then ensure that the Rear Cabinet and the Front Cabinet meet tightly without any clearance, by paying careful attention so that the wiring is not caught in berween.

@® Firmly secure the L type Bracket secured as per @ above by using the 4 Hexagon Bolts.

Hexagon Bolt (black) (4 a M8X20, w/flat & spring washer FIG. 6, 1 ¢

Page 12

SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT)

man Make sure that all of the leg adjusters are in contact with the floor. if they are

CAUTION not, the cabinet may move causing an accident.

This machine has 8 casters (four each for the front cabinet, the rear cabinet) and 6 leg adjusters (4 for the front cabinet, 2 for the rear cabinet) (Fig. 6.2a). When the installation position is determined, cause the leg adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately Smm. from the floor and make sure that the machine position is level.

@ Move the machine to the installation position. When installing the machine against or close to a wall, be sure to secure a pas- Sage space to enable the player to take a ride in the machine.

@® Cause all of the leg adjusters to make contact with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is level.

@ After making adjustments, fasten the leg adjuster nut upward and secure the height of the leg adjuster (Fig. 6.26).

Ca Approx. Sm

FIG. 6.2b LEG ADJUSTER

Page 13

POWER SUPPLY

Ay @ Be sure to ground the Earth Terminal. Unless it is appropriately

grounded, an electric shock accident can be caused to the customers.

@ Ensure that the power cord and Earth Wire are not exposed. If exposed,

they are susceptible to damage and if they are damaged, electric shock

CAUTION!

or a short circuit can be caused. @ Ensure that the power supply is equipped with a Circuit Protector. Using the power supply which is not equipped with the Circuit Protector can cause 4 fire resulting from a short circuit.

The AC Unit is positioned on the left-hand side rear of the Front Cabinet. Connect the AC Unit's Earth Terminal and the " accurately grounded indoor earth terminal" by using the Earth Wire.

Circuit Protector

To AC Receptacle

FIG. 6.3 TURNING ON POWER

Turning the AC unit's MAIN SW on will cause the machine to start the POWER ON check automatically, The steering wheel tums left and right, then retums to the centering position and stops. In this check, the values of V. R. inside the control panel are corrected. Until the check is finished (the steering wheel stops automatically), do not touch the steering wheel or play the game. Tf you do, the steering wheel reaction during the game (reaction at the time of a course-out or crashing) can not be obtained correctly. In a case of a strange reaction during the game, turn on power again from the beginning and complete the power-on check. For communication play, the network check is performed after the power is turned on and the screen display will show the check mode. For details, refer to Section 19.

FIG.6.4 POWER ON CHECK The steering wheel turns left/right automatically, ~10—

Page 14

ASSEMBLY CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 8). In the test mode, perform the following test:

  • MEMORY TEST

Selecting the MEMORY TEST on the test mode menu MEMORY TEST screen causes the on-board memory to be tested auto-

BE soontexe coomatically. The game board is satisfactory if the display
xeii goon3e12 ceedbeside each IC No. shows GOOD. ~

30> Goo feid coon xe) Goon Fed coe,

a

HEM coco1G3$ goedTes Goon1C17_ Good

Here cou cid coor 363 Goo 3150 coop 367 cou dete coop

Yeni coos343 Goonc82 coosC8 coon

xoes coos ie4s coon

3ep3 coop382 aoeze93 coop
3627 toc3C29 coop«EZR oooco coon

PRESS TEST BUTTON TO EXIT -

!

  • INPUT TEST

Selecting the INPUT TEST on the test mode menu ano? TEST screen causes the screen (on which each switch and V.

STEERING WHEEL80HR. are tested) to be displayed. Press each switch. For

ee peas aon the coin switch test, insert a coin from the coin inlet

we oF with the coin chute door being open. If the display be-

ee OF side each switch indicates ON," the switch and wiring SEER (200M Ont) ORE Ascertain the display of V. R. value for the steering oe ae not Satisfactory, refer to Sections 9 & 10

VIEWL {ZOOM IN)GFFconnections are satisfactory.

wheel and accelerator & brake. If the V. R. values are

oeaenot Satisfactory, refer to Sections 9 & 10.

TEST EF PRESS TEST BUTTON TO DaT

  • OUTPUT TEST

Aone In the output test mode, carry out lamp test to ascertain

that each lamp lights up satisfactorily.

CENTERING LEVEL oO

START LAMP OFF VIEW] LAMP (ZOOM IN) Orr VIEW2 LAMP (ZOOM OUT) cfr

SELECT WITH SERVICE BUTTON

AND PRESS TEST BOTION

—i—

Page 15
  • SOUND TEST

SOOND TEST

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

  • CRT. TEST

C.R.T. TEST 1/2

wane In the TEST mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) 10 be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnetism, the location building's steel frames and other game machines in the periphery. By watching the test mode screen, make judgment as to whether an adjustment is needed. If it is necessary, adjust the projector by referring to Section 13.

Perform the above inspections also at the time of monthly inspection.

Page 16
CAUTION TO BE HEEDED WHEN MOVING THE MACHINE

The weight of this machine is approximately 306 kg. When moving the machine on the floor, retract the Leg Adjusters to have the Casters make contact with the surface. When moving the machine in places where there are step-like differences, be sure to separate the Front Cabinet and the Rear Cabinet. Lifting the Cabinet in a status as is connected can damage the Cabinet. .

a o

go fom) t Where to hold aap Separate when moving _ SI [| ced =) FIG. 6.4

Page 17
  • HOW TO PLAY

@ First choose one from among the 3 Courses (the explanations of the 3 courses are given later). Turn the Steering Wheel to choose the desired course and make the selection effective by stepping on the Accelerator (Gas Pedal) or pressing the Start Button. @ When plural machines are interacting, wait for the other player's entry in this screen mode. After all of the players choose their desired courses, a course is determined by a majority decision. In case of a tie, the course will be determined sequentially in priority order of INDY 500, HIGHLAND RACEWAY, and BAY SIDE STREET. Next, select either of the 2 transmissions, AT (auto) or MT (6-shift manual) in the same manner as in Course selection (turn the steering wheel to choose and step on the Accelerator or press the Start Button to make the selection effective. . After the above 2 steps are determined, the game proceeds with a rolling‘start applicable for all the 3 courses. There are 1 ~ 3 checkpoints (varies depending on courses). Passing a checkpoint within the limited time gives the player a time extension. If the player fails to pass the checkpoint within the time limit or if he finishes running the specified number of laps of each course, the game is over. During the race, 4 types of perspectives can be shifted by using the View Button. Pressing the Start Button during the race allows the position of on-screen cars to be indicated above that particular car. Press the Start Buttori again to retum to the previous status. © If the player finishes up to the last and if the total time is satisfactory, name entry up to 10th position per course is allowed.

Features of each course

M@ INDY 500 Number of Laps .......... 4 Number of Checkpoints........ 1 This course reproduces the actual Indianapolis Motor Speedway. It's an oval course very close to a rectangular shape. @ HIGHLAND RACEWAY Number of Laps .......... 3 Number of Checkpoints........ 2 This is an imaginary course on which the machines run through the folds of hills. Sharp ups and downs are the features of this course. Mi BAY SIDE STREET Number of Laps .......... 3. Number of Checkpoints........ 3 Players run through an urban area on this imaginary course. Both sides of the road are concrete walls. This one is the most difficult of all three courses. *The number of Laps are initialized and can be changed in the test mode. Course Map ses Indicates the positions of Position Limited Speed the leading car and the player's car. | 383 3x6 / 7 @®0 8@e@6 6

Course Selection Screen SELECT A COURSE INDYS00

é

mae 7 FIG.7 During-the-game Screen Tachometer. Speed Meter

—{4~—

Page 18
  • EXPLANATION OF TEST AND DATA DISPLAY By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

In the case where multiple units are linked for communication play, exiting from the test mode causes the unit to perform the network check automatically. During this time, all of the linked units will not allow the game

IMPORTANT! io be played in normal status. Therefore, be sure not to enter the test mode if any one of the units is in play. On the other hand, if even one unit is in the test mode, make sUre that other machines are not in play.

TABLES EXPLANATION OF TEST MODE ITEMS DESCRIPTION SEctions INSTALLATION | When the machine is installed, perform the following: - OF MACHINE ‘

  • Check to see that each setting is as per standard setting made at | 8-9. 8-10 the time of shipment.
  • In the INPUT TEST mode, check each SW and VR. g=5
  • In the OUTPUT TEST mode, check each of lamps. 8-6
  • In the SELF-TEST mode, check ICs on the IC Board. 8re —|— MEMORY Choose MEMORY TEST in the MENU mode to allow the

DATA CHECK difficulty level, etc.. 8-2 MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following:

SERVICING 1, MEMORY TEST 8-3

  • Ascertain each setting. 8-9,8-10
  • In the INPUT TEST mode, test the CONTROL device 8-5 4, In the OUTPUT TEST mode, check each of lamps. 8-6
CONTROL1, In the INPUT TEST mode, check each SW and VR.8-5
SYSTEM2. Adjust or replace each SW and VR.9.20.14
  • If the problem can not be solved yet, check the CONTROL's | moves.
MONITORIn the MONITOR ADJUSTMENT mode, check to see if the8-8

PROJECTOR adjustment is appropriately made. 13 b

IC BOARD1. MEMORY TEST-
  • In the SOUND TEST mode, check the sound related ROMs. -

Check such data as game play time and histogram to adjust the 8-12

Page 19

8-1 SWITCH UNIT

Test Button

Service Button

FIG.8.1a SW UNIT Open the coin chute door, and the switch unit shown will appear. The functioning of each SW is as follows:

TEST BUTTON:For the handling of the test button, refer to the following pages.

TEST

SERVICE BUTTONiGives credits without registering on the coin meter.
SPEAKER VOL.:Can adjust the volume of all Speakers of the machine.

SPEAKER

SUPER WOOFER VOL.:Adjusts only the volume of the Rear Cabinet's Super Woofer.

SUPER WOOFER

The contro] panel switches are also used in the test mode. For each functioning, refer to the following page and onward.

Steering Wheel Shift Lever

=a View Change Button 1 (Red) : Brake Pedal

FIG. 8.1 S_Accel. Pedal

Page 20

8-2 TEST MODE

The Test Menu allows the functioning of each part of the Cabinet to be checked, the monitor to be adjusted, and the coins and game related various settings to be performed.

+ Press the TEST BUTTON to cause the following Test Menu to be displayed on the monitor. (FIG. 8.2) 7

+ Press the SERVICE BUTTON or VIEW CHANGE BUTTON (VR) until the pointer "=>" is moved to the desired item to make a selection.

+ Bring the pointer "->" to the desired item and press either the TEST BUTTON or START BUTTON to enter the selected item's test. oa

TEST MENU

MEMORY TEST T.G.P. TEST ' INPUT TEST OUTPUT TEST SOUND TEST C.R.T. TEST GAME ASSIGNMENTS COIN ASSIGNMENTS VOLUME SETTING BOOKKEEPING BACKUP DATA CLEAR ->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8.2 TESTMENU-

+ After the test is complete, move "->" to "EXIT" and press the TEST BUTTON or START BUTTON to retum to the Game Mode.

When changes are made in the settings of GAME ASSIGNMENTS, COIN ASSIGNMENTS and VOLUME SETTING, be sure to exit from the Test

Mode to return to the Game Mode. (if the power is turned OFF in the Test

Mode, the settings can not be rewritten.)

IMPORTANT!

—1i7—

Page 21

8-3 MEMORY TEST

The MEMORY TEST mode is for checking the on-BD memory IC functioning. "GOOD" is displayed for normal ICs and "BAD" is displayed for abnormal ICs.

( ) MEMORY TEST

ae 115 GooD Iclé Goo Icll Goop te1z Goop - Bie) G00 icl0 sGooD tc7 cen rcs oop

<RAMD

C14 GOOD1ci5 GOODici6 = GooDqcl?) Goop

Icig Goop Icigs GooD Tc98 GOOD IciS0 GooD IC7$ GOOD Ic80 GOOD

1c81 GooDIc83 GOODICB2 GOODaic84 Goop-

1C8B «GOOD Ices coop

Tesi GOODTes2. GOOD:re93 GOODé
Ic27 Goopicz9 «GoODIc2B GOODIc30 GooD

PRESS TEST BUTTON TO EXIT

FIG.8.3 MEMORY TEST

@ When the test is completed, if the results are shown as above, it is satisfactory.

@ it takes approximately seventy-five seconds to complete the test. If the TEST exceeds seventy-five seconds, the board may have malfunctioned.

@ After finishing the test, pressing the TEST BUTTON or START BUTTON to return to MENU mode.

Page 22

8-4 T.G.P. TEST

Selecting T.G.P. TEST causes the functioning of the on-IC-BD T.G.P. (screen display related IC's) to be checked automatically. If the IC is satisfactory, "GOOD" will be indicated and if the IC is not satisfactory, "BAD" will be displayed.

a |

T.G.P. TEST

Ic31 GOOD

Ic37 GOOD

PRESS TEST BUITON TO EXIT

ome

FIG.8.4 T.G.P. TEST

@ After the test is finished, if the above are indicated, it is satisfactory.

@ After finishing the test, press the Test button or Start button to retum to the Menu screen.

Page 23

INPUT TEST

‘When INPUT TEST is selected, the monitor will show the following, allowing you to watch the status of each switch and the value of each V. R. of the CONTROL PANEL. On this screen, periodically check the status of each switch & V.R.

By pressing each switch, if the display on the right-hand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory.

To check Coin Chute Coin SW, open the Coin Chute Door and insert a coin(s) in the slot.

To return to the Menu mode, press the Test Button or simultaneously press the Start Button & View Change Button 1 & View Change Button 2. o

INPUT TEST

STEERING WHEEL 80H 7 GAS PEDAL 30H 7 BRAKE PEDAL 308

SHIFT UP OFF SHIFT DOWN OFF VIEWI (ZOOM IN) OFF VIEW1 (ZOOM OUT) OFF

START OFF

COIN CHUTE #1 OFF COIN CHUTE #2 OFF

SERVICE OFF

TEST OFF

a

PRESS TEST BUTION TO EXIT QO FIG. 8.5 INPUT TEST

The appropriate values of each V. R. are as follows:

STEERING WHEEL:Under 2DH+-7D~83H-+Over D3H

left (Centering position) tight

GAS PEDAL:Under 30H_Over COH
BRAKE PEDAL:Under 30H—Over COH.

(the pedal released) (the pedal stepped) "

—~20—

Page 24

8-6 OUTPUT TEST

This test allows the Steering Wheel 's centering strength and the status of each lamp to be checked. .

OUTPUT TEST

CENTERING LEVEL 0

START LAMP OFF

VIEW1 LAMP (ZOOM IN) OFF

VIEW2 LAMP (ZOOM OUT) OFF

~PEXIT ,

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

X / HiG.8.6 OUTPUT TEST

TEST PROCEDURE

@® Press either of the Service Button or the View Change Button to move the arrow ~> to the desired test iter. @® To perform the test, press either the Test Button or the Start Button. Each time the Test Button is pressed, the CENTERING LEVEL varies from (0 ... Naught to 8 ... strongest) in 9 steps. Check the Steering Wheel’s centering strength by changing the centering level. To check each lamp, bring the arrow to the desired item and press the Test Button . The on-screen display will indicate “ON” and the corresponding lamp attached to the Cabinet lights up. Press the Test Button again to cause the on-screen display to indicate “OFF” and the lamp to go off. @® Move the arrow to EXIT and press either the Test Button or Start Button to return to the Menu screen.

Page 25

8-7 SOUND TEST

This test mode allows each sound related board and speaker to be checked.

SOUND TEST

No. 0

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

NX —_______/ FIG.8.7 SOUND TEST

@ Press either the Service Button or the View Change Button to change the sound.

@ Press either the Test Button or the Start Button to return to the Menu mode.

Page 26

8-8 C.R.T. TEST

Choose C. R. T. TEST to have the following screen for monitor adjustment appear.

C.R.T. TEST 1/2

. GREEN

BLUE

| WHITE

PRESS TEST BUTTON TO CONTINUE

FIG.8.8a C.R.T. TEST

The C.R.T. TEST as shown in FIG. 8.8a allows for monitor color checking. Each of the 4 colors, i. e., R (red), G (green), B (blue), and white is darkest at the left-hand end and becomes brighter towards the right-hand end. In the FIG. 8.8b, adjust the monitor to make sure that the crosshatch lines do not go beyond the screen size and crosshatch distortion does not occur. Press either the Test Button or the Start Button to have the following crosshatch screen appear.

SCOTT TTT my -R.T. TEST 2/2 Co

] ro T im a

H

i py bit ! i TEST BUTTON TO EXIT Lt TUTTI TTT Ti rTt coy

FIG.8.8b C.R.T. TEST

Press either the Test Button or the Start Button to return to the Menu mode.

~23—

Page 27

8-9 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the menu mode causes the present game seiting to be displayed and also the game setting changes can be made. Each 1 item displays the following content.

CO

GAME DIFFICULTY NORMAL RACE MODE NORMAL .

HANDICAP on COUNTRY USA

ADVERTISE SOUND ON

CABINET TYPE DELUXE NETWORK TYPE STAND ALONE CABINET ID 1

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON GAME ASSIGNMENTS

FIG. 8.9 GAME ASSIGNMENTS

@ GAME DIFFICULTY

@ RACE MODE The game difficulty can be varied by changing the time allowed at the time of race start and the additional time allowed when passing the checkpoints. Choose from among the following 5 categories. (Standard difficulty is NORMAL.)

  • VERY EASY
  • NORMAL
  • HARD
  • HARDEST

The Race Mode has 2 types, NORMAL and LONG. Number of Laps can be changed. (Standard setting is NORMAL.)

INDY 500 | HIGHLAND} BAY SIDE NORMAL | 4Llaps [| 3Laps | 3Laps LONG | 20Laps | 17Laps | 15Laps |

Page 28

HANDICAP

ADVERTISE SOUND

COUNTRY

CABINET TYPE

NETWORK TYPE

CABINET ID Set to ON when using this setting to make correction for speeding up the cars whose position is No. 2 or lower in the vs. interactive competition. If not using this feature, set to OFF. (Normally, this is set to ON.)

Set this to ON to have sound produced during Demo mode and to OFF for not producing sound.

Message Language (select USA for the U.S.A., and EXPORT for other countries.)

Set to DELUXE.

There are 3 types, i. e., STAND ALONE, MASTER and SLAVE. Choose STAND ALONE for a single player. For interactive play, choose MASTER for one unit and SLAVE for the remaining units.

When cabinets are linked for interactive play, use the ID number sequentially in order starting from the leftmost cabinet. Otherwise, on-screen display in the ADVERTISE mode will not be consistent in continuity between units.

For Communication play, refer to 19. COMMUNICATION PLAY.

SETTING CHANGE PROCEDURE

Press the SERVICE button or VIEW CHANGE button to move the arrow (>) to the desired setting change item.

Press the TEST button or START button to make a setting change selection.

Move the arrow to EXIT and press TEST button or START button to return to the MENU mode,

Page 29

8-10 COIN ASSIGNMENT

The "COIN ASSIGNMENTS" mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses "how many coins correspond to how many credits.”

™

COIN ASSIGNMENTS

COIN/CREDIT SETTING # 18 COIN CHUTE #1 1 COIN 1 CREDIT

COIN CHUTE #2 1 COIN 1 CREDIT

MANUAL SETTING ->EXIT ‘

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON », mm, FIG.8. 10a COIN ASSIGNMENTS

@ COIN/CREDIT SETTING "How many coins correspond to how many credits." In this machine, selection as per Table 8.10a is possible.

@ MANUAL SETTING Allows for finer settings. (Table 8.10b)

SETTING CHANGE PROCEDURE

@® Press the SERVICE button or VIEW CHANGE button to move the arrow (->) to the desired setting change item.

@ Press the TEST button or START button to make a setting change selection.

@® Move the arrow to EXIT and press TEST button or START button to retum to the MENU mode.

Page 30

TABLE 8.10a COIN/CREDIT SETTING [RaME OF SETTING | FUNCTIONING OF COIN CHUTE #1 FUNCTIONING OF COIN CHUTE #2

SETTING #11 COIN1_ CREDITJ COINL CREDIT
SETTING #2 1 COIN2_ CREDITS1 COIN1 CREDIT
SETTING #3 1 COIN3 CREDITS1 COIN1 CREDIT
SETTING #4 1 COIN4 CREDITS1 COIN) CREDIT|
SETTING #5 | 1 COIN3 CREDITS1 COINi CREDIT
SETTING #6 tL COIN2_ CREDITS1 COIN2_ CREDITS
SETTING #7 1 COIN5_CREDITS1 COIN2_CREDITS i
SETTING #8 1 COIN3 CREDITSL COIN3 CREDITS,
SETTING #9 | 1 COIN4 CREDITS1 COIN4 CREDITS
SETTING #10 1 COIN3_ CREDITS1 COIN5_ CREDITS
L SETTING #11 1 COIN6_CREDITS1 COIN6 CREDITS

SETTING #12) 2 COINS | CREDIT 2_ COINS 1 CREDIT

SETTING #13 1 COIN| CREDIT2 COINS i CREDIT
SETTING #14 1 COIN2_ CREDITS2_ COINS 1 CREDIT
SETTING #15 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 3 CREDITS 2 COINS 3_ CREDITS

| SETTING #16 1 COIN3 CREDITS1 COIN1 CREDITS. |

2 COINS 3 CREDITS | SETTING #17 3 COINS 1 CREDIT 3 COINS 1_ CREDIT SETTING #18 | 4 COINS 1 CREDIT 4 COINS 1 CREDIT

SETTING #19 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS 3 COINS 3 CREDITS 3. COINS 3. CREDITS 4 COINS 5 CREDITS 4 COINS 3 CREDITS

SETTING #20 1 COIN 5 CREDITS 1 COIN 1 CREDIT 1

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5_ CREDITS SETTING #21 5_COINS 1 CREDIT 5 COINS 1 CREDIT

SETTING #22 1 COIN2 CREDITS3 COINS 1 CREDIT

3_COINS 2 CREDITS SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT 4 COINS 2 CREDITS 4 COINS 2 CREDITS 5 COINS 3 CREDITS 35 COINS 3 CREDITS

SETTING #24 1 COIN3 CREDIT2 COINS 1 CREDIT

4 COINS 2 CREDITS 3 COINS 3 CREDITS

SETTING #25 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS 3 COINS 3. CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 4 COINS 4 CREDITS 5_COINS 6 CREDITS 5 COINS 6 CREDITS

SETTING #26 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5S COINS 6 CREDITS SETTING #27 FREE PLAY FREE PLAY

Page 31

MANUAL SETTING

MANUAL SETTING

COIN TO CREDIT 1 COIN ICREDIT BONUS ADDER NO BONUS ADDER

COIN CHUTE #1 MULTIPLIER i COIN COUNTS AS 1 COIN

COIN CHUTE #2 MULTIPLIER re

1 COIN COUNTS AS 1 COIN

->EXIT

SELECT WITH SERVICE BUTTON _ AND PRESS TEST BUTTON ;

FIG, 8.10b COIN ASSIGNMENTS

@ COIN TO CREDIT Determines conversion coins/credit.

@ BONUS ADDER This sets how many conversion coins should be inserted to . obtain one Service Coin.

@ COIN CHUTE #X MULTIPLIER This sets how many inserted tokens one conversion coin represents.

Page 32

TABLE 8. 10b MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT a

2 COINS 1 CREDIT

3 COINS 1 CREDIT

4 COINS 1 CREDIT

5 COINS 1 CREDIT 6 COINS 1 CREDIT

7 COINS 1 CREDIT

8 COINS 1 CREDIT

9 COINS 1 CREDIT

BONUS ADDER

a

[coIn CHUTE MULTIPLIER NO BONUS ADDER 2 COINS GIVE

EXTRA COIN

COINS GIVE

COINS GIVE

COINS GIVE COINS GIVE

COINS GIVE

COINS GIVE

WL PN Hp oy pd

COINS GIVE

1 EXTRA COIN

COIN COUNTS AS COIN. | COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS mt fap a] mf ee] ef me] a]

COIN COUNTS AS WD NW] OD) ON] |] wi) rj)

COINS

Page 33

8-11 VOLUME SETTING

This setting mode allows V.R. value for each of Steering Wheel and Pedal

VOLUME SETTING

SETTING WHEEL MAX 93 (DF) GAS PEDAL MAX 78 (CO} BRAKE PEDAL MAX 3H (C5) MIN 93(26) MIN 78(78) MIN 3E(3E)

-> CANCEL & EXIT SET & EXIT NEW 93(93)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 8.11 VOLUME SETTING

V.R. VALUE SETTING PROCEDURE

®

®

® Step on the GAS PEDAL fully and then release it. Step on the BRAKE PEDAL fully and then release it. . Tum the Steering Wheel fully to the left & right, and maintain the centering position by referring to the level line shown. ® Press either the Service Button or the View Change Button to bring the artow (~>) to SET & EXIT. While maintaining the Steering Wheel's centering position, press either the Test Button or Start Button to set V.R. value set, returning to the Menu mode. Bringing the arrow to CANCEL & EXIT and Pressing either the Test Button or Start Button causes the Menu mode to return on the screen without setting the V. R. value. ™ to be set.

Page 34

8-12 BOOKKEEPING

Selecting the BOOKKEEPING in the menu mode displays the bookkeeping data up to the present on the following 2 pages.

Press the TEST button again to proceed to the next page.

BOOKKEEPING 1/2

COIN CHUTE #1 COIN CHUTE #2 TOTAL COINS COIN CREDITS SERVICE CREDITS TOTAL CREDITS NUMBER OF GAMES TOTAL TIME OH OM OS PLAY TIME OH OM OS AVERAGE PLAY TIME OH OM OS LONGEST PLAY TIME OH OM 0S SHORTEST PLAY TIME OH OM 0S t weuvo000c000 oo

PRESS TEST BUTTON TO CONTINUE

FIG.8.12a BOOKKEEPING (1/2)

BOOKKEEPING 2/2

TIME HISTOGRAM OMCOS~OM29S OM30S~OM59S 1M00S~1M29S 1M30S~1M59S 2M00S~2M29S 2M30S~2M59S 3M00S~3M29S 3M30S~3M59S “4M00S~4M29S 4M30S~4M59S OVER 5SMO0S ogooc00000000

PRESS TEST BUTTON TO EXIT

FIG. 8.12b BOOKKEEPING (2/2)

@ COIN CHUTE#® Number of coins put in. As seen from the front of the cabinet, the righthand side is #1 and the left- hand side is #2.

@ TOTAL COINS Total number of coins inserted in each coin chute. @COIN CREDITS Number of credits registered by inserting coins @SERVICE CREDITS — Credits registered by the SERVICE button @ TOTAL CREDITS Total number of credits (COIN CREDITS + SERVICE CREDITS) @ TOTAL TIME The total energized time. @ TIME HISTOGRAM __ By-playtime play frequency.

Page 35

8-13 BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING. When clearing, use the Service Button or View Change Button to bring the arrow (~>) to "YES (CLEAR)" and press either the Test Button or the Start Button. When the data has been cleared, "COMPLETED" will be displayed. Press the Test Button or the Start Button to retum to the Menu mode. Bring the arrow to "NO (CANCEL)" and press either the Test Button or Start Button to return to the Menu mode without clearing the data. Also, note that the game setting contents are not affected by BACKUP DATA CLEAR operation.

( 5

BACKUP DATA CLEAR

YES (CLEAR) ->NO (CANCEL)

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

NL

FIG. 8.13 BACKUP DATA CLEAR

Page 36
  • CONTROL PANEL

A | @ This unit is a heavy item weighing approximately 21kg. and therefore, be very careful when performing the work.

CAUTION! @ Immediately after the game is finished, the motor may still be very hot. When performing the removal work, wait until the motor cools off. a)

On the Test mode, if the Steering Wheel's V. R. variations are not within the allowable range, the V. R. installation position adjustments or V. R. replacement are needed. Also, be sure to apply greasing to the V.R. Gear portion once every 3 months.“

9-1 REMOVING THE CONTROL PANEL

@ Remove a total of 6 Tamperproof Screws from the upper and lower parts of the Control Panel. At this time, be sure to firmly hold the Control Panel so as not to drop it.

@ Carefully draw the Control Panel from the Front Cabinet. At this time, pulling out the Control Panel completely may cause wiring breakage, therefore, be sure to draw it halfway and not completely.

@ Disconnect all of the Connectors connected to the Front Cabinet.

@® Pull out the Control Panel completely. When putting it down, be very careful so as not to damage the V. R. portion of the motor's rear end.

TAMPERPROOF SCREW (black) (6)

Page 37

9-2 ADJUSTING AND REPLACING THE V. R.

The V. R. on the right-hand side of the Steering Wheel Mechanism is for the Game BD & Drive Control, and the V. R. on the left-hand side is for the Motor Control BD. Check V. R. values in the Test mode. The appropriate values of each V.R. are as follows:

Left Centering position Right

For Game BD & Drive Control: 2DH orlower — 7DH~83H > D3H or higher For Motor Control: 2DHorlower — 7DH~83H -> D3H or higher

REPLACING THE V. R.

After disconnecting the V. R. to be replaced, take off the 2 screws which secure the VR. Bracket by using the Spanner, and then remove the V.R. with the gear as is attached. After replacement, check V-R. value variations in the Test mode.

V.R._for Motor Control BD (3P_vellow Connector) V.R. for Game BD & Drive Control 220-5373 or 220-5484 ; - (3P_red Connector) i WA 220-5373 or 220-5484

M4X12, w/flat and spring washers = BSS sory , M4x12, w/flat and spring washers

Page 38

ADJUSTING THE V. R.

@® By using the Spanner, loosen the 2 screws which secure the V.R. Bracket, move the V.R. Bracket and disengage the gear mesh.

@ Ensure that the V. R. value is within the range of the centering position.

@® Mesh the gears to secure the V. R. Bracket. At this time, ensure that an appropriate backlash is obtained.

S) When the Steering Wheel is in the centering position, if the V.R. value is not appropriate, make fine adjustments by loosening the 2 screws which secure the V. R. - gear, turing the gear holder and making sure that the V.R. value is appropriate.

® Turn the Steering Wheel to check V. R. value variations.

9-3 GREASING

Apply greasing to gear portions once every 3 months.

APPLY GREASING

Page 39
  • SHIFT LEVER

In the Test mode, if the SHIFT LEVER's $W can not be inputted satisfactorily, replace the Switch. Apply greasing to the Mechanism's sliding portion once every 3 months. When performing the above work, remove the Shift Lever Unit,

10-4 REMOVING THE SHIFT LEVER

@ Remove the 4 Tamperproof Screws to lift the Shift Lever Unit. @ Disconnect the Connector to temove the Shift Lever Unit. @ When reinstalling, follow the procedure opposite as when removing. At ‘this time, ensure that "DOWN" display appears on the upper part as shown.

TAMPERPROOF SCREW (black) (4)

FIG. 10.8

PIN 2

10-2 SWITCH REPLACEMENT

Method of replacement

® Disconnect the wiring Connector of the Switch to be replaced. @® Remove the 2 Tapping Screws (M3 X 16) to replace the Microswitch.

10-3 GREASING

Apply greasing once in 3 months to the L _ specified portions. \ ~ NICROSRITCH

FIG. 10.2

—~36—

Page 40
  • ACCELERATOR & BRAKE

In the test mode, if the ACCEL. & | BRAKE V.R. value is not within the allowable range, an adjustment of V.R. installation position, or a replacement of V. R. is needed. Also, grease the Mechanism's shafts and sliding portions once every 3 months. ‘When performing the above work, remove the 6 Hexagon Bolts and carefully draw the Unit (the weight of which is approximately 6kg.) in the manner not to damage the wiring.

HEEAGON BOLTS (black) (6) \| M8X30, w/flat & spring washers FIG.11

11-1 ADJUSTING AND REPLACING THE V.R.

Pull out the Unit, and ACCEL. & BRAKE Mechanism/appears. The V. R. on the lefthand side of the Mechanism is for the ACCEL., and the V. R. on the right-hand side of the Mechanism is for the BRAKE. Check the V.R. values in the test mode. The appropriate value of each V.R. is as follows:

When released: When stepped on: Under 30H Over COH Under 30 H Over COH

Method of V. R. replacement

To replace the V. R., after taking off the connector from the V. R. to be replaced, take out the 2 screws which secure the V. R. Bracket, and remove the V. R. together with the bracket and gear. After the replacement, check the V. R. value variations in the test mode.

SCRER (2. M4x8,using spring washer

SCREW(2) M4X8,using flat & spring washers

Page 41

| Method of V. R. adjustment

® Loosen the 2 screws which secure the V.R. Bracket and move the V. R. Bracket to disengage the gears,

@ Have the V.R. value match with the value obtained when the pedal is released.

@® Mesh the gears to secure the V.R. Bracket. At this time, be sure to obtain an appropriate backlash.

@® Step on the pedal and check V. R. value variations. If the value is not within the above

1-2 appropriate range, loosen the 2 screws which secure the ADJUST GEAR to make an adjustment.

GREASING

Apply greasing to the gear and shaft portions once every 3 months.

Apply greasing in the following procedure:

@® Remove the 4 Tamperproof Screws (black) which secure the Pedal Cover and remove the Pedal Cover by moving it forward.

® Remove the Pedal Shaft from the lower portions of ACCEL. pedal and BRAKE pedal. At this time, ensure that the ACCEL pedal and BRAKE pedal are firmly secured as they are subjected to torsion spring force.

® After applying greasing to each part, assemble in the procedure opposite as when disas-

EAS: sembling.

_GREASING Accel. side & / Brake side LGREASING Accel. side & PEDAL SHAFT TAVPERPROOF SCREW (black) Brake side

  • Maxs

GREASING Pedal Shaft removed as per @ above.

FIG. 11.2

Page 42
  • COIN SELECTOR

If the coin is not rejected even when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Tum the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). Remove stain by wiping with a soft cloth which contains water or chemical detergent. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the shaft. Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. ® ® 8 oO

©

® After wiping off as per 5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the Coin Selector. @ After cleaning the Coin Selector, insert a regular

IMPORTANT!

coin in the normal working status and ensure that the Selector correctly functions.

COIN INSERTION TEST Once every month, when performing f

the Coin SW Test, simultaneously Insert, @ coin

check the following: the Reject Button pressed down and check if it is (1 Does the Coin Meter count satisfactorily? [1] Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down? a

Page 43
  • PROJECTOR

A @ Since the Projector screen can be easily damaged, handie with carel. m1 When cleaning, do not use water or volatile chemicals.

CAUTION @ Since the Projector has been adjusted at the time of shipment, avoid

making further adjustments without good reason.

13-1 REMOVING THE MONITOR MASK

nN The Monitor Mask is of a very large size and has glass portions. Be sure

to perform the work by plural persons.

CAUTION!

@® Take out the 2 Truss Screws and open TRUSS SCREW (2 the Roof Lid attached to the Billboard W4x8, chromeplated by using the Master Key.

@® Lift the Billboard Case (the weight of which is approximately 8 kg.) and carefully remove it by moving it towards you. At this time, pay attention to the Fluorescent Lamp which is on the Front Cabinet side.

BILLBOARD CASE

Be careful of the Fluorescent Lamp.

TRUSS SCREW (4 N5X25, flat washer used

@® Remove the 4 Truss Screws from both sides of the Front Cabinet. At this time, slightly support the Monitor Mask so as not to allow it to fall down.

FIG. 13.16

Page 44

@ Slightly lift the Monitor Mask and carefully remove it forward. Be careful of At this time, pay careful atten- the Fluorescent tion to the Fluorescent Lamp above. .

. th

FIG. 13.1¢ a ae

© When reinstalling, use the procedure opposite as when removing. Be very careful of the Fluorescent Lamp. .

13-2 CLEANING THE MONITOR MASK

When cleaning the Monitor Mask, follow the instructions below so as not to damage the Front Glass.

@ Use alcohol based cleaner (liquid) agent. @ Use soft cloth. @ When removing adhered

IMPORTANT!

extraneous matter such as large particles (dust), etc., do not rub them with cloth.

13-3 CLEANING THE SCREEN

When the screen surface becomes dirty with dust, etc., clean it by using a soft cloth such as gauze. Water, and volatile chemicals such as benzine, thinner, etc., will damage the screen surface, and should not be used. Also, since the surfaces can be easily damaged, avoid rubbing them with any abrasive materials or using a duster.

Page 45

13-4 ADJUSTING THE PROJECTOR

Never touch places other than those specified. Otherwise, hazardous electric shock or short-circuit can be caused.

CAUTION! Take out the 6 Truss Screws from Front Panel L of the front portion of the Front Cabinet, and the Projector's Control Panel appears. O PROJECTOR CONTROL PANEL

Truss Screw (black)(3) M4 X30 V.HOLD

BRIGHT

CONTRAST

Hy POSITION Ven!

STATIC. COVER- GENCE DYNAMIC!

FIG, 13.4 @ v.HOLp @sricht @conrRast @H. POSITION @® Vv. PosITION

| STATIC CONVERGENCE ADJUSTMENT

Do not touch the Dynamic Convergence Adjustment SW. Dynamic Convergence adjustment work is quite troublesome and the visual effect is

CAUTION! expected to be negligible. As such, no explanation is given in this manual. Should the SW be pressed by mistake or otherwise, turn the power off and turn it back on again.

CROSS PATTERN

ie) Press the Static Convergence Adjustment SW which is on

the Control Panel to cause the cross pattern to appear.

@ Use the remote contro! to make static adjustment. For the operation of the Remote Controller, refer to the following pages.

® Press the Static Convergence SW. At this time, static adjustment results are written and the PTV screen will return to the original screen mode.

Page 46

The Remote Controller has 2 different types. Depending on the specific type, the adjustment procedure varies.

In the case of Remote Controller (Part No. 220-5297):

REMOTE CONTROL If the Convergence adjustment is incorrect, a red or blue line may appear to move when a Remote Control Numeral Key is pressed after the cross pattern _ 8s appears. If the line is superimposed on the green cross pattem, the cross pattem a. becomes white. NI~FLRT RS ICTs)

+o NANFA At he

SIOISIOISISS) STTTST) favszy)

a5 les 1 none] [amar

15] [ova = +

Make sure that the slide portion of the Remote Control is positioned as per @ above. Press BS]. Position the slide portion of the Remote Control to @ in the above Figure. Press VIDEO 1. Position the Remote Control's slide portion to the above ®. Press “ +” to have the cross patiern appear. Use the remote coroller to make static adjustment.

Remote control [ 2 ],{ 5 }.....Causes the red horizontal line to match with the green horizontal line. Remote control { 4 },{ 6 ].....Causes the red vertical line to match with the green vertical line. Remote control [ 8 ],{11].....Causes the blue horizontal line to match with the green horizontal line. Remote control [10], {12].....Causes the blue vertical line to match with the green vertical line. Position the Remote Conwrol's slide portion to @ in the above Figure and push "OFF" 5 times to retum to the normal mode.

Page 47

In the case of Remote Controlter (Part No. 220-5410):

If the Convergence adjustment is incorrect, a red or blue line may appear to move when a Remote Control Arrow Key is pressed after the cross pattern appears. If the line is superimposed on the green cross pattern, the cross pattem becomes white. '

@® Have the Remote Controller face the Projector screen and press Key 1, 2, and 3 (Portion @ shown) of the Static Convergence Adjustment sequentially in order, causing the cross pattem to be displayed. Press the following arrow keys (Portion @) shown) to make adjustments.

Causes the red horizontal line to match with the green horizontal line. Causes the red vertical line 10 match with the green vertical line.

Causes the Blue horizontal line to match with the green horizontal line. Causes the Blue vertical line to match with the green vertical line.

@® Press the CANCEL Key (Portion @ shown) 5 times. This operation allows for returning to the original screen and at the same time storing the adjustment data.

Page 48
  • REPLACEMENT OF FLUORESCENT LAMP

To replace the Fluorescent Lamp, remove the Billboard Case by referring to@ and @ of 13-1 REMOVING THE MONITOR MASK.

FIG. 14

Page 49
  • PERIODIC CHECK

‘The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation,

Tern * Interval Reference

CONTROL PANELCheck lamp.Monthly8

[~ Check VOLUME VALUE. Monthly 6. 8

Check ADJUST GEAR engagement.Trimonthly9-1
Greasing of GEAR.| Trimonthiy9-2,9-3
ACCEL. & BRAKECheck VOLUME VALUE.__| Monthly6, 8
Check ADJUST GEAR engagement._{ Trmonthly1li-l
LGreasing of GEAR and bearing.| Trimonthly11-2
SHIFT LEVERCheck SW.Monthly6, 8
GreasingTrimonthly10-3-_|
FRONT CABINETCheck COIN SW.‘Monthly8
Coin insertion test.Monthly12|
Cleaning of COIN SELECTOR.Trimonthly12
| PROJECTOR7Check adjustments._| Monthly6, 8,13
Cleaning of screen.Weekly13-3

L Cleaning of glass Appropriate time i= 3-2 iL Check settings. Monthly 8

GAME BDMEMORY TEST.Monthly8
LREAR CABINETGrease the Seat Rail portion.TrimonthlySee below

REAR CABINET (Greasing to Seat Rail Portion) _| Move the Seat to the rearmost portion and apply spray greasing a to the portion shown at the right once every 3 months fC.

After greasing, move the Seat a few times forward and backward so as to allow the grease to be applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the Seat Rail, or any excess grease. FIG. 15

Page 50
  • TROUBLESHOOTING

In case a problem occurs, first check wiring connector connections.

PROBLEMS CAUSE COUNTERMEASURES

When the main SW is tamed ON, the machine is not activated. | Filmy insert the plug into the outlet. ‘The power is not ON.

Incorrect power source/voltage. Make sure that the power supply/voliage are correct.

The CIRCUTI PROTECTOR functioned

duc 10 momentary overcurrent. Reset the AC Unit's Circuit Protector.

PTV screen color is not

correct Sereen adjustment is not appropriate. "| stake adjustments appropriately.

PTV screen has a color deviation. Affected by the periphery, such as other machines, location building's steel frames,

etc. Make convergence adjustments.

Change installation direction/ position.

Move the’other machines which causes the problem.

No image is projected on the PTY screen. Connector connection is incorrect, | check connector connection inside the Roof Lid and je Panel L.

Sound is not emitied. Sound volume adjustment is not correct. Adjust SW Unit's speaker volume.

Malfunctioning BD. and Amp. ae sound test to check it. Check the connector connection inside the Roof Lid.

‘Woofer sound is not emitted.

ae Connector connection is incorrect.

Sound volume adjustment is incorrect, Adjust SW Unit's woofer volume.

Connector connection is incorrect, Check connector connection inside the Roof Lid, and

Front & Rear cabinets.

Operation of Accel., Brake and Pedal are not Satisfactory. V.R_ position deviated. Adjust V.R. value in the test mode.

V.R. malfunctioning.

ADIUST GEAR's engagement is not

correct. Replace the V. R.

Adjust the engagement of ADJUST GEAR.

SHIFT LEVER doesn't operate satisfactorily. Switch malfunctioning. Replace the SW.

Steering Wheel reaction strength is incorrect. Deviation of Center. Power ON check not performed correctly. qn ‘um off power and then tum it back on again. Com-

plete the power on check.

V.R. position deviated. Adjust V. R. value in the test mode.

V.R. malfunctioning. —t Replace the V. R.

Page 51

PROBLEMS CAUSE COUNTERMEASURES

Steering Wheel reaction | Reaction Mecha's secular change. Change Drive Control BD DIP SW setting. strength is insufficient.

No Steering Wheel Connector Connection is incorrect. Check connector connection in the Roof Lid, Front Reaction. Pane] L, and Service Door.

The Motor Drive BD fuse is blown due to Replace the Motor Drive BD Fuse. momentary overcurrent.

Fluorescent lamp does Fluorescent Lamp needs replacement. Replace the fluorescent lamp. Pa not light up. | Connector connection is incorrect. ‘Check connector connection in the Roof Lid.

A Be sure to turn off power

before performing the work.

CAUTION! p i

To replace the Motor Drive BD Fuse, Be sure to use the specified fuse for open the Front Cabinet's right-hand the Motor Drive BD (838-11966). side Service Door.

Page 52
  • GAME BOARD

17-1 REMOVING THE BOARD

To replace or check the Game Board, remove it by using the following procedure:

® Turn off the Main SW.

@® Remove the 2 Truss Screws from the Roof Lid and open the Roof Lid with the Master Key.

@ Take out the 3 Screws and remove the Shield Case Lid from the Shield Case in the center. The Game Board can be viewed.

@) Take out the 5 screws to remove the Shield Case Lid which is beside the Case Lid in the center, and the Drive Control BD appears.

Truss Sereys_ (2 W4xX8 a

Screw {5. M4X8, w/flat and spring washers

Screw (3) N4x8, w/flat and spring washers

Page 53

17-2 COMPOSITION OF GAME BOARD GAME BD INDY 500 (833 - 11992)

ROM BD_TNDY 500 834~11993 M3X5, flat and spring washers used

i° oO

1C5S tsomn a MPR-18244 5 1034 somo 39 MPR-18243 1G33 tomo 2 MPR-18242 1032 ssouwn 93 MPR-18241 ora 834 -11993) 57 EPR-18249 VC30 (corre MPR-46232 EPR-19250 MPR~10234 1e22 War MPR-15236 MPR-18233 123 vor 1G 27 aextuee 3 10168 Wor 7 MPR-16235 1C+7 W0r oF IC 2O 1 1C24 ror VOz4 (ee, TC29 1e0rno oF 1C26 (vextune

i 1C3% sow oy EPR~1682S3 Bes TC}S Waaonau oF EPR-18251 EPR-18252 MPR-10236 MPR-18237 Tet? waa TE1G Weoamau v1 eta aes

17-3 INPUT AND OUTPUT RELATIONS INDY 500 “est Botton, Service Bu: ton, Coin SF, free, ‘Srart 2: “ch ar

Foofer VolumeSpeaker VolumeCoin kerSteering WheelSteering Reaction Kotor

| v

8386-11651838-11650-05833-11992838-119676838-11966
£0. PwR<—J Gave BODRIVEMOTOR
LOWPASS AMPAMP INYTROY S00 oxCONTROL 8DDRIVE 8D

Super Woofer Beoe Speakers? 200-5394 ASSY PTY 3¢° WIE CP

FIG. 17.3

Page 54

DRIVE CONTROL BOARD

The Steering Wheel reaction strength is set by the Drive Control Board DIP SW. To perform the setting, open the Billboard and remove the Lid of the Shield Case for the Drive Control BD. Be sure to turn off power before performing the work. Use Nos. 1~3 of DIP SW J of the Drive Control BD. Tum off all other DIP SWes.

oy

i |

| O ie e) 3! Ty) swe Cee a ARG Citoresw: a 8500 is

DRIVE CONTROL BD (838-11967)

DIP SW SETTING

NOTE: The shaded portion refers to the setting at the time of shipment.

—5i—

Page 55
  • DESIGN RELATED PARTS
Page 56
NO.PART NO.DESCRIPTION
IDYN-0010DENOMI PLATE
3422-0536-01PLAY INSTR SH INY ENG
64220-0537-01SUB INSTR SH INY ENG
84400-CS0011-EGSTICKER C GRIP HANDLE ENG
9INY-1201-BSHEET METER
10INY-1203-BSHEET EMBLEM
llINY-1251-BSHEET VR SW
124230-0249BILLBOARD PLATE INY
13INY0-1502-BSTICKER BASE LINE L
i4INY0-1502-CSTICKER BASE LINE R
15INYO-1502-DSTICKER BASE LINE B
16INYO-1604-BSTICKER BASE LINE CENTER
i7INY0-1604-CSTICKER SEAT L
18INYO0-1604-DSTICKER SEAT R
i9421-8890DESIGN PLT SHIFT UP
20421-8891DESIGN PLT SHIFT DOWN
21421-8901STICKER INY PTV L
22421-8902STICKER INY PTV R
23421-8930STICKER INY PTV LOWER L
24421-8931STICKER INY PTV LOWER R
254210-8935STICKER INDY CAR No. “2-8”

(for use with linked machines)

Page 57
  • COMMUNICATION PLAY

19-4

(fastened with 2 screws) INDY 500 allows 2~8 units to be linked for interactive play. For communication play, communication cable connection and Game Assignments are needed.

INSTALLATION PRECAUTIONS .

When linking a number of machines, be sure to supply sufficient power for the corresponding number of machines. The per unit standard voltage/amperage is 100~ 120V/ 10A and 200~240V/5A. Remove the Hole Lid which is beside the BILLBOARD (only for the Communication Cable passage side).

BILLBOARD

FIG. 19.1

Install the machines by referring to the following illustrations.

Ensure that the height and depth of the machines are consistent with each other so that the holes beside the Billboards also match.

—~54—

Page 58

19-2 CONNECTING THE COMMUNICATION CABLES

nN The Communication cables are made of Optic Fiber. Excessive bending

AUTON can damage it. Handle with care. + Open the Billboard's Roof Lid and connect the Communication Cable to the Shield Case for the Game BD (refer to FIG. 19.2 a).

FIG. 19.24

Depending on the number of machines to be linked, connect Communication cables as shown in FIG. 19.2 b.

CLT unitary To To ‘ r

CABINETCABINETCABINETCABINETCABINET
1D 4ID2if 11D 2i10 3

2P LINK SP LINK

IPL I) TT Ly

|gliorca |sg)|

: } \ } \ \ \ i CABINET CABINET | CABINET CABINET |

asID 1m2|fo 3[Oo 4i

a fF i 4P LINK

se

Page 59
CABINETCABINETCABINETCABINETCABINET
D710 2iD 3IDms

SP LINK

Jt— kej >ii |
CABINETCABINETCABINETCABINETCABINETCABINET
ID1D 212 3[oO 410 &10 6

BP LINK

+

Cag ineTCABINGTcaBIneTcagineycagineyCag ner
rasto 210310'S.

a S| fe {ff ia

CABINETCABINETcasingsCABINETcag pnetcapinercanineTcasiney
tosoe10 4:ty¢2

FIG. 19.2b

Page 60

TAPORTANT! SETTING COMMUNICATION PLAY

When communications are stopped during interactive play, due to some cause, the game will be interrupted and the Network Check mode will appear on the screen.

When performing communication play ,GAME ASSIGNMENTS in the Test mode need to be changed. First determine the Master unit and set the NETWORK TYPE to MAS- TER. Thereafter, the settings of Game Difficulty, Race mode, Handicap, Advertise Sound, and Country must follow the settings made by the Master Unit. Next, Cabinet ID is set sequentially in order of 1 » 2+ 3 ... starting from the leftmost unit.-

GAME ASSIGNMENTS

GAME DIFFICULTY NORMAL ; RACE MODE NORMAL

HANDICAP ON COUNTRY EXPORT

ADVERTISE SOUND ON

CABINET TYPE DELUXE NETWORK TYPE MASTER CABINET ID 1

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 19.3

Have all the machines exit from the Test Mode. The Network Check starts and after a while, the game mode appears on the screen.

Page 61

19-4 APPLICATION OF STICKER

Apply the Seat No. displaying Sticker Numbers 2~8 (421-8935) to the positions shown sequentially in order of 1, 2, 3, 4 starting from the leftmost linked unit (facing the screen).

Siam

i]

am a ion ica] 0 io Ni || Osh eed

FIG. 19.4

—5B—

Page 62
  • PARTS LIST INDY 5060 DELUXE ASSEMBLY

Marquee

Speaker, Tweeter (2) 130-5112 Speaker Box Dome 130-5113

Assy PTV 39" Monitor 200-5394

Over/Under Coin Door and Cash Box

Seat Assembly INYO-1600

Rear Base Assembly INY0-1501

SN Casters (8) Levelers (8) 999-0169 999-0167 Ficure 20-1: Inpy 500 DeLuxe CABINET ASSEMBLY Underseat Speaker, Woofer 130-5114

Page 63

GAS AND BRAKE PEDAL ASSEMBLY P/N: DYN1-1300

Figure 20-2: Gas AND BRAKE PEDAL ASSEMBLY

Page 64

GAS AND BRAKE PEDAL ASSEMBLY P/N: DYN1-1300

Table 20:-1 Gas and Brake Pedal Parts List

NO.PART NO.DESCRIPTION
1DYNO-1301PEDAL BASE
2DYNO-1306ACCEL PEDAL
3DYNO-1307BRAKE PEDAL
4BVG0-1404PEDAL COVER
5BVG0-1405SWING ARM A
6BVGO0-1406SWING ARM B
7BVGO-1407PUSH ROD
8BVG0-1408PUSH PLATE
9DYN-1302RUBBER BUMPER
10BVG0-1410PUSH ROD PIN
ilBVG0-1411LINK ROD
12DYNO-1303TORSION SPRING ACCEL
13BVGO0-1413TORSION SPRING B
14BVG0-1414RUBBER STOPPER
15BVG0-1415PEDAL SHAFT

Te BVG0-1416 SWING ARM STOPPER

7BVGO0-1417SPACER
18GLCO0-2122GEAR PLATE
i9RDM-1210VR BRACKET
101220-5373VOL CONT B - 5K OHM

220-5484 VOL CONT B - 5K OHM ALT

102601-6005ADJUST GEAR
103601-5943GEAR 20 @ 15
201000-P00408-WM SCREW PH WI/FS M4 X 8
202600-P00408-SM SCREW PH W/S M4 X 8
203000-P00416-0BM SCREW PH BLK M4 X 16
204000-T004080-0BTMP PRF SCREW TH BLK M4 X 8
205050-H00600NUT HEX M6
206060-F00800-0BFLT WASHERBLK M8
207060-S01200-0BSPR WASHER BLK M12
208060-S00600SPR WASHER M6
209060-S00400-0BSPR WASHER BLK M4
210065-E00600E RING 6MM
211028-A00308-PSET SCR HEX SKT CUP P M3 X8
212068-652016FLT WASHER 6.5-20 X 1.6
213DYN-1304FLT WASHER BLK 4.4-12 x 1.6
214DYN-1305FLT WASHER 12.2-22 X 0.5
Page 65

CONTROL PANEL ASSEMBLY P/N: INY-1200

TORQUE 200kgf + ca

Ficure 20-4: Controt PaNeL ASSEMBLY

Page 66

CONTROL PANEL ASSEMBLY P/N: INY-1200

Table 20-3: Control Panel Parts List

iB sauawnel? S8sssss B8RSsege PART NO. INY-1201 INY-1202 INY-1203 INY-1250 DYN-1201 DYN-1209 OUT-2026 610-0383 6100-0384 050-H00800 050-F00400 060-S00800 000-T00412-0C 008-T00512-0B DESCRIPTION CONTROL PANEL COVER CONTROL PANEL BRKT STEERING EMBLEM ASSY VIRTUAL BUTTON STEERING WHEEL HANDLE COLLAR SPACER ASSY HANDLE MECHANISM W/MOTOR UP/DOWN SHIFTER HEX NUT M8 FLG NUT M4 SPR WSHR M8 M SCR TH CRM M4 X 12 TMP PRF SCR TH BLK M5 X 12

Page 67

VIRTUA BUTTON ASSEMBLY P/N: INY-1250

(RED) (BLUE)

Figure 20-5: Virtua BUTTON ASSEMBLY

Table 20-4: Virtua Button Parts List

NO. PART NO. DESCRIPTION

i INY-1251 VR SW BRACKET

2 171-6478B PC BD LIGHTING SWX5

101212-5205-12CONN JST M 12P RTA
102509-5560-YPB SW WIL 6V ILY
103509-5561-RPB SW W/L 6V5LR
104509-5561-SPB SW W/L 6V SLS
Page 68

MASK ASSEMBLY P/N: INY0-1300

££

Details of PART A

A port ion o

Ficure 20-6: MASK ASSEMBLY

Table 20-5: Mask Parts List N iO. PART NO. DESCRIPTION

1INY0-1301MASK FRAME
2INY0-1302INNER MASK
3INY0-1303FRONT PLEX

INY0-1304 CORNER SASH

Page 69

BILLBOARD CASE ASSEMBLY P/N: INY0-1410

Oxy

Figure 20-7: BILLBOARD Case ASSEMBLY

Table 20-6: Billboard Case Parts List

NO. PART NO. DESCRIPTION

1INYO-1411BILLBOARD CASE
2INY0-1412CORNER EDGE
34230-0249BILLBOARD PLATE INY
Page 70

BILLBOARD BASE ASSEMBLY P/N: INY-1420

=.

a AR

; = 0 o

Ficure 20-8: BiLBoarp Base ASSEMBLY

Table 20-7: Billboard Base Parts List NO. PART NO. DESCRIPTION 101 2601-0011-02 AXIAL FLOW FAN AC120V50-60HZ 12VDC FL30W 36 INCH FLUORESCENT ASSY

Page 71

WOOFER ASSEMBLY P/N: INY0-1550

Ficure 20-12: WooFER ASSEMBLY

Table 20-11: Woofer Parts List .

NO. PART NO. DESCRIPTION

1 INY0-1551 WOOFER BRKT 101 130-5097 SPEAKER BOX SUPER WOOFER

Page 72

Figure 20-13: Sear Assempy

ASSBMBLY DBTAILS CASSY)

TORQUE MB i50kgf+cm SEAT ASSEMBLY P/N: INY0-1600

Page 73

SEAT ASSEMBLY P/N: INY0-1600

Table 20-12: Seat Parts List

NO.PART NO.DESCRIPTION
1INY0-1601UPPER SEAR
2INY0-1602LOWER SEAT
3INY0-1603SEAT BACK COVER F
4INY0-1604SEAT BACK COVER R
6INY0-1606SEAT FRAME BRKT
7RALO-2081SEAT FRAME TWIN
10INYO-1605SEAT BASE
101999-0443SEAT RAIL SET
201030-000845-SHEX BLT W/S M8X45
202030-000850-SBHEX BLT W/S BLK M8XS0
203050-H00800-0BHEX NUT BLK M8
204060-S00800-0BSPR WSHR BLK M&
205060-F00800-0BFLT WSHR BLK M8
206000-T00412-0C=MSCRTH CRM M4x12
207068-441616-0CFLT WSHR CRM 4.4-16X16
208000-P00412-WM SCR PH W/FS M4X12
Page 74

ELECTRICAL ASSEMBLY P/N: INY1-4000

Figure 20-14: ELECTRICAL ASSEMBLY

Page 75

ELECTRICAL ASSEMBLY P/N: INY1-4000

Table 20-13: Electrical Assembly Parts List NQ. PART NO. DESCRIPTION

2INY0-4300ASSY SHIELD CASE
3838-11650-05EQ. PWR AMP INY
4838-1165]LOWPASS AMP
6INY0-4600ASSY DRIVE CONTROL BD

101 999-0102 150W SWITCHING XT 5601-5260 PWR XFMR 12.5V 6A/100V 6.54

Page 76

MOTOR DRIVE BOARD ASSEMBLY P/N:

Ficure 20-16: Motor Drive Boarp AssemBLy

Table 20-15: Motor Drive Board Parts list NO. PAR’ DESCRIPTION 838-1 1966, MOTOR DRIVE BOARD

Page 77

SHIELD CASE ASSEMBLY P/N:

Figure 20-17: Supp CASE ASSEMBLY

Table 20-16: Shield Case Parts List NO. PART NO. DESCRIPTION

11050-5218SHIELD CASE
21050-5219SHIELD CASE LID
3833-11992GAME BD INDY 500

4 839-0818 ‘FLT BD B-CRX INY 102 2601-0055 FAN MOTOR DC5V

Page 78

DRIVE CONTROL ASSEMBLY P/N: INY0-4600

oe9000000000 90000000000 o0c00000000 00009000000 Q0000000000 ° 1@ iS} ° 2900000000000000000000000060000 099090000000000000000000000000000 9000000000000000000006000000050 009000009000000000000000000000000 0000900000000000000000000000000 podosetoselolelelelojejolelololejelelelejelerelelelejeleleleley 00900000000000000: lofeletoicloleiolelelele) 9900900000000000000000000000000 69099000600000090000000000000000 029900000000000000000000000000006 0900000006000000000000000000000

Figure 20-18: Drive ConTROL ASSEMBLY

Table 20-17 Drive Control Parts List NO. PART NO. DESCRIPTION

1INY0-4601SHIELD CASE
2INY0-4602SHIELD CASE LID
3838-11967DRIVE CONTROL BD
4839-0829FLT BD DRIVE CONTROL BD A
5839-0830FLT BD DRIVE CONTROL BD B
Page 79

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 80

“ASSY REAR BASE

ASSY COINCHUTE TOWER

TNY-1160 INy-1501

ASSY ACCEL & BRAKE fimum

OYN-1300

Iny-1200. ASSY CONTROL PANEL # ASSY_FRONT CABINET

Iny-1101 ASSY BASE

838-11966 MOTOR DRIVE 8D (INY=4299)

A 8

¥ VI ASSY CO

610-0383 c 2 eka nator INY-1200 r 7 - ASSY CONTROL PANEL

JRELEASE USA VERSIOR 7 bern tees

A B

Page 81

Saa-165

  • seorsnen INY-1420 LOwrass a wre tus ASSY BILLBOARD BASE

f; 330-5530-3750 200-5394 ASSY PTY 33° wide cp ** Stes Te. FL 32 > Iny-4000 ASSY ELEC

son INy-4300 r : é we re oer) - ASSY SHIELO CASE Be 32 Sa fg ee Py en 9834-11993 BS ROM BD INOY 500 nadia tit

yy ; 4888 RE

ra i

4888 be:

Es i

i INY-1160 Y COIN. SE Etter 8633-11992 GAME BD INDY 500 $8888 thet 839-0818

FLT 8D 8-CRX INY

Ft R

9837-11996 CO BD INDY SCO TO (272)

ASSY DRIVE CONTROL BD

NY~1200 4 CONTROL EL

HH

INY-1101 ASSY BASE INy-4000 ASSY ELEC USA VERSION

SO a Se eeBW SEGA SEGA ENTERPRISES, LTD. PeSSRAICAEL M10 wt 8 Conn. 9 77 RS PETS HoT OR tf & i SEGA INDY 500 DX 1173072)

  • To E F y G Oo
Page 82

INY-4600 ASSY DRIVE CONTROL BD 838-11967 DRIVE CONTROL BD 800-6603-64 30] 3a

  • 50 Famenere go000

o a 600-6609-56 1x 7] 80} Sb TO (172)

600-6609-65 FLT_BD DRIVE CONTROL BD B 833-0830

°

o STEERING Al 204 4

‘GND Fane asron 9000000 S24] 5095 JST NI UST NH 12P

TO] pon cena ca FLT BD DRIVE CONT 839-0829

Page 83

UST NH 18P

ayesre wanes & = EERE EE beeess BESBES >

USA VERSION

SEGA SECA ENTERPRISES, LTD. THIS DRAMING WILL IN RO MAY BE COPIED. FF IFT 7 MRS TO BE RETURED ON DEMO, aReeR SEGA INDY 500 DX 1173(272) ESET id

Page 84
  • INDY 500 DELUXE MANUAL COMMENTS

SEGA has made every effort to ensure that this manual is accurate. If you find any errors or omissions, or have other comments on the Indy 500 Deluxe manual, please write them below, detach, and deliver this page by FAX or mail to:

SEGA ENTERPRISES INC. (USA) ATTN: Engineering Dept. 45133 Industrial Drive Fremont, CA 94538 USA FAX: (415) 802-1754

Comments:

Optional Identification Information:

Name: Company: Address: City, State, Zip: Phone: FAX: