CATHODE RAY TOMES

Hippodrome Installation and Service Manual (780-0129-00)

Hippodrome (US) (Data East USA, 1989) · Installation · 55 pages · 9 sections · original scan

Page 1

INSTALLATION AND SERVICE MANUAL

for

UPRIGHT GAME

and

CONVERSION. KIT

DATA EAST USA, INC, 470 Needles Dr. San Jose, CA 95112

Page 2

‘|

FCS WARNING ‘equpment cenerates and uses race frequency enersu end if net Metaled and used broverty, je; in strict accordance: fistructons mantis, may couse harmful niterfereee to rodo commanscancns: Thes ecuoment has been tested fa ccercs whit) at ne 9 aes ome sees we ie oo eee 70 provide reasonable protection scainst such-mtertercnce when the equoment is operated in a commercial. this equoment in a residential environment is Rely to cause nierference fi which case the user, at hs own beremored te take whatever meamres sre necessary to correct ihe nierterence.

FEDWARRING

Federal law provides severe chad ond -crininat penalties forthe tncuthorted reoroduction, distribution, or exiybition of ee audio "sual works and video games, The fF ederai Bureau of Investigation mvestigates ategations o7 cranmal fe

COPYRIGHT NOHCS

HIPPODROME Tts Copuricht: 1988 Data fast Corporation, sold exélucwely in the United Staies of America and Canada by Data East USA, ne. Ad rights reserved.

ENVIRONMENTAL DATA = This product is intended for use indoor use only, power requirements ars SOS-25 volts AG SG-S0 ty, and requires ad: wire grounded outer.

SERVICE PROCEDURES

To obtain replacement parts and technical service; contact the authorired Data East Distributor in your area. Hf you require referral or turiher fechhical assistance, you mey contact Data Easi’s Customer Service department during the hours of. G00 am-to $-00.om Pacitic Time af 408) 286-7074,

AaMA WARNING DATA -EAST-_USA, INC. —“in_cooneratien with the—Amerncan Amusement Mactune Association, has installed an Se PROTECT" certification iabel on cach = “HIPPaDROME = PCE manufactured for legai salem the United States of América, Tf you are offered a—HIPPODROME — PCG that does net have the “RAMA PROTECT" certifcation label, vow shoud ee ee DATA EAST USA NC, af (408) 286-7074, oe bob Fad oF (EMA ahCroD) S48-

Page 3

HIPPODROME™

UPRIGHT GAME and CONVERSION KIT

Table of Contents

UPRIGHT GAME A. Installation and Setup. B. System Adjustments... C. Replacement Parts Lists.

CONVERSION KIT A. — Specific Requiremens. B. Replacement Parts List. C. Installation Instructions..

GAME INFORMATION A. Game Options. B. PCB Edge Connector Pin-outs..

SCHEMATIC DIAGRAMS A. DE 0318-3 Program Boar B. DE 0297-3 Main Board.....

CUSTOMER REPLY FORMeesssssensnetntnentd 49

WARRANTY INFORMATION. Inside Back Cover

© 1989 DATA EAST USA, INC. 470 Needles Dr. San Jose, CA 95112

Page 4

HIPPODROME™

UPRIGHT GAME

  • A. INSTALLATION AND SET UP

Thank you for buying a DATA EAST product. We are sure that you will enjoy many years of profitable and entertaining operation with your HIPPODROME™ game.

Your game was thoroughly tested, ’burned-in’ and inspected before it was shipped. However, it may have been subjected to some rough handling, or a rough ride in a truck, since it left our factory, so please follow the steps listed below before attempting to operate the game.

Locate the door keys supplied and remove the Rear Access Door.

Check the Main Harness for loose or unplugged connectors, and check for secure mounting of the monitor, power supply, and game pcb. Stabilize the cabinet using the leg levelers in the floor of the cabinet to prevent the game from rocking.

The selectable options have been pre-set at the factory for optimum player appeal. However, to set the game up for your specific requirements, refer to the operator selectable options on Page 10 in Chapter 3, Section A of this manual.

Remove the power cord from the inside of the cabinet and insert the strain relief plate into the slot at the bottom of the rear access door opening. Plug the AC cord into a grounded 117 VAC outlet and flip the power switch to the ON position. Allow 2 to 3 minutes for the monitor to warm up and check for proper demonstration mode video on the screen. Insert the proper coinage into a coin slot and start a game. Check for proper operation of all joystick controls and switches.

Page 5

HIPPODROME™ UPRIGHT GAME

I. B. SYSTEM ADJUSTMENTS

The Volume Control, Coin Counter, and Service Switch are located on the Service Panel. The Service Panel is located inside the Coin Door, mounted on the wall of the cabinet on the left side.

The Coin Counter increments once for every coin dropped through either coin entry slot.

HIPPODROME™ utilizes monophonic sound. A single Volume Control is used to adjust the overall loudness of the game sounds. NOTE: The volume control potentiometer on the Main PC Board is pre-set to mid-range at the factory and should not be adjusted.

The Service Switch can be used to add credits to the game without incrementing the Coin Counter.

The fuses for the AC power line and the 12 volt Supply are located on the Power Supply assembly. The fuse holders are labeled as to the proper fuse ratings. The line fuse should be 3 A slow blow, and the 12 volt fuse (used for coin door lamp circuit) should be 1 A fast blow.

The +5 vde adjustment level control on the Power Supply’s Switching Regulator is pre-set at the factory. In the event that an adjustment is required, measure the +5 volt level present at the game logic pcb with a Digital Multi-Meter while adjusting the output level of the Switching Regulator. The voltage must measure between +4,90 vde to 5.10 vde at the game logic pcb for proper operation.

WARNING: DANGEROUS VOLTAGE LEVELS ARE PRESENT IN AND AROUND THE MONITOR AND POWER SUPPLY ASSEMBLY. ADJUSTMENTS AND REPAIRS SHOULD BE ATTEMPTED ONLY BY QUALIFIED ELECTRONIC TECHNICIANS.
Page 6

HIPPODROME™ UPRIGHT GAME

I. C. REPLACEMENT PARTS LISTS

The following lists indicate the major replaceable parts for your HIPPODROME” Upright Game, Control Panel Assembly, Service Panel Assembly and Power Supply Assembly. When ordering replacement parts, please be sure to provide both the complete description and part number.

—_ 1 P/N 500-0039-00 Upright Game l 1

Part NumberDescriptionRemarks

031-0005-00 Speaker, 5" deluxe

365-0013-00Cabinet Assy, 1US34-stylegray (45 deg)

380-0002-00 Bezel, Monitor, black

510-0002-03Power Supply AssySv-11a, 12v-1a

510-0004-00 Coin Door Assy, 2 slot 510-0065-00 Monitor, Universal H/V 510-0151-00 PCB Set, Hippodrome 510-0155-00 | Control Panel Assy, Hippodrome 515-0029-02 Panel Assy, Service 535-0078-00 Retainer, Plex, Marquee 660-0001-01 Plex, Clear, 23.75 X 23.75

660-0001-07Plex, Clear, 26.06 X 7.6 X .125(for marquee)

780-0129-00 | Manual, Service & Operation, Hippodrome 810-0040-00 | Underlay, Monitor, Hippodrome

820-0040-00Decal, Side, Generic 5.13.87Blue
830-0045-00Overlay, Marquee, Hippodrome(for marquee plex)
Page 7

HIPPODROME™ UPRIGHT GAME

  • C. REPLACEMENT PARTS LISTS (continued)

l 1 P/N 510-0155-00 Control Panel Assembly

  • I Part Number Description 180-0024-00 Pushbutton Assy, w/microswitch, Black 180-0024-02 Pushbutton Assy, w/microswitch, Red 180-0024-04 Pushbutton Assy, w/microswitch, Yellow 406-0180-02 Tag, Pushbutton ID, "2 Players" 406-0180-05 Tag, Pushbutton ID "1 Player" (upside down) 406-0180-07 Tag, Pushbutton ID, "Jump" 406-0180-16 Tag, Pushbutton ID, "Attack" 450-0014-01 Joystick, Happ Ctrl, 8 way, w/Microswitches 535-0061-00 Control Panel, Bare 800-0030-00 Overlay, Control Panel, Generic, Blue

f 1 P/N 515-0029-02 SERVICE PANEL ASSEMBLY l | Part Number Description Comments 090-0002-00 Coin Counter, 12 volt w/internal diode 123-0008-11 Potentiometer, 100 n, 4 watt Volume Control 180-0024-xx Pushbutton Assy, w/Micro switch (any color will do) 535-0084-00 Bracket, Service Panel

r P/N 510-0002-03 POWER SUPPLY ASSEMBLY —_ 1 Part Number Description Comments 001-0012-00 Switching Regulator +5 V @ 11A, 12V @ 2A 010-0001-00 Transformer, Isolation 1 A (min) @ 115 VAC 150-0006-00 Filter, Noise Delta # 10DKAGS5 200-0002-00 Fuse, 1 A Fast Blow for Coin Door Lamps 200-0011-00 Fuse, 3 A Slo Blow 115 VAC Line Fuse 515-0002-01 Power Cord Assy wi/strain relief plate 660-0003-00 Fish Paper (safety cover)

Page 8

HIPPODROME™ CONVERSION KIT

  • A, SPECIFIC REQUIREMENTS

Thank you for purchasing a DATA EAST game. We hope that it will give you many years of productive enjoyment. Your HIPPODROME™ game conversion kit is intended to be installed into an existing video game cabinet, and comes with all the necessary components to make the converted unit look and play like a new, dedicated game.

THE GAME TO BE CONVERTED MUST MEET THE FOLLOWING REQUIREMENTS

MONITOR: Horizontal, RGB, Negative Composit Sync Input

POWER SUPPLY: + SVDC @ 10 amp, +12VDC @ 1 amp

  • B. REPLACEMENT PARTS LIST

The following items are provided with your HIPPODROME™ generic kit. When ordering replacement parts, please be sure to provide the complete description and part number.

Part Number Description Remarks

036-0158-02 Hrns, JAMMA - GENERIC KIT 180-0024-00 Pushbutton Assy, w/microsw, Black 180-0024-02 Pushbutton Assy, w/microsw, Red 180-0024-04 Pushbutton Assy, w/microsw, Yellow, 406-0003-00 Label, FCC Warning 406-0085-00 Label Set, Pushbutton ID 450-0014-01 Joystick, w/Microswitches Happ Contrls 510-0151-00 PCB set, Hippodrome 660-0001-00 Plex, Clear, 23.75 X 7.6 (for control panel) 660-0001-02 Plex, Clear, 24 XK 9 X .125 (for marquee) 780-0129-00 Manual, Inst., Hippodrome 800-0030-00 Overlay, Ctrl Pni, Generic blue DATA EAST 810-0040-00 Underlay, Mon. Hippodrome 820-0040-00 Decal, Side, Generic blue DATA EAST 830-0045-00 Overlay, Maquee, Hippodrome

Page 9

HIPPODROME™

CONVERSION KIT

  • C. INSTALLATION INSTRUCTIONS

When selecting a game to convert, make sure that the Power Supply, the Monitor, and the Coin Acceptors are functional. There is nothing more frustrating than installing a conversion kit and having it not operate due to a faulty monitor or power supply. You should not expect the new logic PCB to be defective. It has been thoroughly tested and "burned-in’ at the factory.

It is mandatory that the cabinet be wired to conform with all National and Local electric codes before the conversion is attempted. The primary power input section must have adequate noise filtering on the AC line to prevent undesirable conducted radio frequency interference (RFI). “Adequate" is defined as a filter with both common mode and differential mode filtering and a minimum current capacity of 2.5 Amp.

The Federal Communications Commission (FCC), and other regulatory agencies, require that every video game be clearly labeled with the Name and Address of the Original Manufacturer, Date of Manufacture (or Serial Number), Power requirements, Suitability for indoor or outdoor use, and the Model number of the unit. DO NOT DESTROY OR DEFACE THE ORIGINAL GAME ID TAG. In addition, the FCC requires that, after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable label is included with this kit.

IT IS THE RESPONSIBILITY OF THE PERSON INSTALLING THIS KIT TO COMPLY WITH ALL LABELING REQUIREMENTS!

2.C.,, TAKING IT APART

Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit.

Find the Wiring Diagram of the game to be converted. You will need to identify the required DC power supply output wires and the monitor video and sync wires. Note the color coding of these wires, or better yet, label them as to their function. This kit contains a new Main Harness, but you will need to splice it into the existing power supply and video wiring.

Remove the existing game harness parts that will not be used in this conversion. NOTE: You are modifying only the secondary (DC from power supply) and I/O (video, speaker, and controls) sections of the wiring. DO NOT MODIFY OR REMOVE THE PRIMARY AC WIRING. The original manufacturer should have designed and built it to comply with Local and National Electrical Codes and FCC regulations. It must not be altered.

Page 10

HIPPODROME™

CONVERSION KIT

2.C., TAKING IT APART (continued)

Remove the original game pcb from the cabinet. Remove all exterior decals, and repair any cabinet damage. Repaint the cabinet if necessary. Remove the monitor plex (or glass). If your plex has silkscreened art work on it, you will need to strip it off, or replace it with a new piece cut to the same size. Using the old Monitor Plex as a template, cut the Monitor Underlay card, supplied with this kit, to the same size as the old plex. NOTE: Be certain that the opening in the Underlay Card lines up with the monitor screen.

Remove the Marquee Plex from the game and use it as a template to cut the new Marquee Plex down to the correct size. Remove the control panel from the game and remove all controls and graphics from it. Drill and/or punch any required new holes for the control panel. HIPPODROME* is an interactive, two player game (player vs. player, or player vs. computer), and requires two joy sticks. Each player also requires a minimum of two "shoot" buttons, although four are recommended (to allow either player to ’shoot’ either left handed or right handed). See the diagram below for a suggested control panel layout. If you are going to cover the control panel with clear plex, you should carefully cut it to fit the control panel at this time. Thoroughly clean the control panel so that the new control panel overlay will adhere to it aggressively.

2.C., PUTTING IT TOGETHER

Install the Control Panel Overlay by peeling off the paper backing and carefully laying the overly down on the panel. Smooth it out starting in the center and working your way out to the edges, removing all of the trapped air pockets. If possible, cut the edges of the overlay oversize and fold the excess under the panel. Cut out the button and joy stick holes. Install the BUTTON {D labels supplied with the kit.

FIGURE 1 - Suggested Control Panel Layout

0 O@OO 0 OWO O JUMP ATTACK ATTACK JUMP JUMP ATTACK ATTACK JUMP

Page 11

HIPPODROME™

CONVERSION KIT

2.C., PUTTING IT TOGETHER (continued)

‘You may wish to cover the control panel overlay and button ID labels with clear plex at this time. Install the new buttons and joy stick at this time. Refer to Figure 1 on the previous page for recommended control layout.

GAME PCB: Mount the Game PCB in a convenient location in the cabinet, using the mounting feet and hardware supplied with the pcb.

MAIN HARNESS: The generic, main harness provided with this kit has a standard, 56 pin JAMMA connector. All required RFI filtering is incorporated on the PC Board. No external filtering is required. The Game pcb has a 56 pin, JAMMA connector. Refer to Figure 2, on page 11 for information pertaining to signals and functions as they are found on the game pcb edge connector.

POWER SUPPLY WIRING: Separate the DC power wires and route them through the cabinet to the Power Supply. Try to keep the length of these wires to a minimum for best results.

NOTE: USE A MINIMUM OF TWO (2) WIRES EACH FOR THE +5 VOLTS AND THE GROUND LINES BETWEEN THE POWER SUPPLY AND THE PCB. Terminate these wires at the power supply as required.
NOTE: IMPROPER WIRING WILL DAMAGE THE PCB SET AND VOID

THE WARRANTY!

PLAYER CONTROL WIRING: Route the push button and joy stick wires up to their proper destinations, cut to length, and terminate as required.

MONITOR WIRING: The game outputs are Positive for the Red, Green and Blue signals, and Negative Composite Sync. If your monitor has separate Horizontal and Vertical sync inputs, hook the Composite sync to the negative Horizontal] input. This method will work on most monitors. However, some Electrohome models require that the Composite sync signal be hooked up to both the negative Horizontal and Vertical inputs. Contact your distributor for more information if you are uncertain as to how to hook up the monitor wires.

COIN DOOR: The coin counter(s) may be the 12 volt or the 6 volt type, as the game pcb utilizes an open collector drive circuit. Hook one coin counter wire to the required, positive voltage and the other wire to the coin counter signal wire from the main harness edge connector. Refer to the standard connection diagrams on page 12.

Page 12

HIPPODROME™

CONVERSION KIT

2.C., PUTTING IT TOGETHER (continued)

GRAPHICS: The monitor underlay card is pre-printed with game instructions. Install the underlay card under a clean, clear plex or glass. Check any marquee lamps for proper operation. Replace any burned out lamps. The HIPPODROME™ marquee overlay must be installed on a piece of clear plex. Before you do that, use the old plex as a guide for cutting the 24 x 9" clear plex (provided with this kit) to the proper size. Next, remove the protective coverings from the clear plex, and carefully clean it with a good, anti-static cleaner to remove any and all specks of dust, etc, that may have been attracted to it. Then remove the paper backing from the marquee overlay, and affix it to the clear marquee plex. Make sure that the copyright notice will not be hidden by any plex retainers when installed. Smooth out any and all bubbles. Install the two DATA EAST side decals.

IMPORTANT! Install the "FCC Warning" label to the upper rear of the cabinet.

———, || THE BIG TEST! || ————EE—————

Remove the Main Harness connector from the game pcb. Apply power. Measure the +5 volts at the edge connector of Main Harness (at the point where it would connect to the game pcb). Adjust to +5.15 VDC using a Digital volt meter. Measure the +12 volts and the -5 volts (if any) to ensure that they are connected properly and are on the correct terminals. TURN THE POWER OFF! Now reconnect the Main Harness connector to the game pcb, and apply power once again. The attract mode video should appear on the screen. Adjust the picture size and colors on the monitor to get the optimum appearance. Adjust the Sync and Hold controls on the monitor for a stable picture. Coin it up and give it a try! Test all the controls and check the sound for proper operation.

CONGRATULATIONS! You have successfully installed your DATA EAST conversion kit. We hope that it gives you may years of successful operation.

Page 13

HIPPODROME™

UPRIGHT GAME & CONVERSION KIT

  • A. OPERATOR SELECTABLE OPTIONS

The HIPPODROME® game allows for operator adjustable pricing, number of lives, difficulty, etc. These are accessed by the two 8 position dipswitches located on the main logic pcb. Tables 1 and 2 outline the available options.

TABLE 1 - Dipswitch 1

Game Charge 1 coin = 1 credit] OFF OFF (Right) 1 coin = 2 credit] ON OFF COIN 1 2 coin = 1 credit| OFF ON 3 coin = 1 credit) ON ON

Game Charge1 coin = 1 credit]OFF OFF
(Left)1 coin = 2 creditON OFF
COIN 22 coincreditOFFON

3 coin = 1 credit ON ON

Attract Mode Yes: No:

Flip Screen? Normal:

TABLE 2 - Dipswitch 2

2 Lives: 3 Lives: 1 Lifes 5 Lives:

NORMAL > Game bifficuity EASY: HARD: HARDEST:

Power Level (player & enemy)

Enemies Power Decrease when game is continued

Page 14

HIPPODROME™

UPRIGHT GAME & CONVERSION KIT

TABLE 2 - JAMMA Connector

WIRE COLOR SOLDER SIDE PIN#

BK GROUND Al BK GROUND A2 RD +5 VOLTS A3 RD +5 VOLTS A4 BL -5 VOLTS AS OR +12 VOLTS A6 BLOCKING KEY A7 VI COIN COUNTER 2 A8 AQ WH/BK SPEAKER (-) A10 GN All GR VIDEO-GREEN A12 WH VIDEO-SYNC A13 YL SERVICE SW. Al14 A1S RD COIN SWITCH 2 A16 RD/WH 2P START A17 YL/WH 2P UP A18 GN/WH 2P DOWN A19 OR/WH 2P LEFT A20 RD/WH 2P RIGHT A21 BL/WH 2P SHOOT A22 VI/WH 2P JUMP A23 PK/WH NOT USED A24 A25 A26 BK GROUND A27 BK GROUND A28 PIN#

  • B. PCB EDGE CONNECTOR PIN-OUTS

PARTS SIDE WIRE COLOR

GROUND BK GROUND BK +5 VOLTS RD +5 VOLTS RD -5 VOLTS BL +12 VOLTS OR BLOCKING KEY COIN COUNTER 1 SL

SPEAKER (+) BK/WH

VIDEO-RED RD VIDEO-BLUE BL VIDEO GROUND BK TEST SW. * BK/GN COIN SWITCH 1 GN 1P START BN/WH 1P UP YL 1P DOWN GN 1P LEFT OR 1P RIGHT RD 1P SHOOT BL 1P JUMP VI NOT USED PK

GROUND BK GROUND ~* BK

Page 15

HIPPODROME™

UPRIGHT GAME & CONVERSION KIT

  • C. STANDARD CONNECTION DIAGRAMS

FIGURE 2 - Coin Counters & Coin Switches

COIN Swi on NO CoM Samer 1[__ Ye COIN SW 2 on Ch NO. fea] SWITCH 2

Page 16
Scan of page 16

This page is a drawing, shown as the original scan.

Page 17

u {> Meq (6-18),

nreeoe (6-SE) aor (6-16) MeGADL (6-26) 'P/sp (8-26),

6 Con,

wo Con Cae} boca [oe

enix pacetoLolen “> a8cGAd (7-1E)

Receapip (7- AE) *eacaserq (7-46) worcgual an poset (7-AE) waecnoei[e

cur Hosten we

DE 0318-3 PCB 1/1?

Page 18

9 | >

ianr,tii Pinv4tuare

> Bicaap (1-SE)

areca

3 }—) 4 i st s % «fo 1 (3-4 é ten} 1GxjJ— —_" et u(t p(s JY 3(ox | Cee] Gas] arets COs]

ene aieaanto [2S BICGAMLD (7-TE) aiceoce [AK] seiaseto (T-TE) sie oes [a3 4OIGSELI (7-BE) coun f

Corer) . avieap (ATT ¥viep (8-1)

ienudao Coa«HOO (8-1E)

tm veunt [at P— NC

a0an [oRnan(e-1e)

io

ee : ent a3 i ca Ky

DE 0318-3 PCB 1/17

TTT o

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

> SAB (1-28) a

le

sé [e S82. (16-56) sew [arf aod (16-SE)

[> sos (4 A)

scan [E35} {> wan (7-48)

tt

lc

ie DE 0318-3 PCB 1/17 ar ees

A

Page 21

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 24

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 25

(8-SE) BIMApAD

8-88) wranno (§-8B) mart wae (BRB) RAR WRIT 8-38) parapea [>

(8-68) B2col,

(8 -ADHCLE [ ppt 1304 {> coven (2-46) na

lov

Page 26

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 27

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 32

1 L 2 Ll 3 \ 4 Ll 5 L 6 L 2 1 8 [more s Tan, an

1/17 PCB DE 0318-3 cng ca-34) $08 |

UbM4A) SUR SA) SRD -SAy MSRA

34> xRST

tv

026) sown | (a-eysounnk |

a _ ___ == — [325 1334 SAB] &_ 1 ff Pi |S) ae, DES | & i ft ik,

Page 33

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

! + BK craw xb D>

mt @-%a) BUNKS [> cyr6ay

Cow).

aay i fa mas pikes

PCB DE 0297-3

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

HE

ue te

ne re

Chad Rew cpvaR [S>-—————__——_. pues

B6c. ai3ay COL

to-day “* UBS, iG-3A) Moser 8 UA) 209 G-3n) *PSEL} USA) wy uw) (asta) ore

HLWR, a-fA), #8 [ 82, DHSS

| eR | BE

HET-E1 Beak Evy

Lk-(0060 ~|

) erser S— a a PCR 1/17 DE 0297-3

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

a isk co vio |=

ik, BH G@I—~<+ev I<] 180

TIRTL-T FSiu Proaqnot t

GN DA

cs Th “we & Te

Ko id ' 4.Y tH d SBze33 O4 3 Uf . 2 2 For? 3 hee 4 2 3 #3 3 | _ wm | ik. ze

HFT-El 38a Lk-l0060-1

“p> y¥sutna (5-26) a7 PCB DE 0297-3

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 52

HIPPODROME™

UPRIGHT GAME & CONVERSION KIT

  • 0. CUSTOMER RESPONSE

This HIPPODROME™ Installation and Service Manual includes schematic diagrams, and should answer almost all of the technical questions that you may have. Should you require additional, or more detailed information, you should contact the DATA EAST distributor from whom you have purchased the game. His highly qualified staff will, most likely, be able to answer your questions, or give you the proper direction. If, after consulting with your distributor, you still require additional assistance, you may contact the DATA EAST service department at (408) 286-7080, between the hours of 8:00 AM and 5:00 PM Pacific time. When contacting your distributor, or when contacting DATA EAST, please be prepared to provide the serial numbers for the game pcb (printed on the original product seal), the "AAMA PROTECT" sticker, and the game cabinet.

DATA EAST welcomes all constructive feedback, both negative and positive. We would be pleased if you would write us directly with you comments concerning our products and services. Our address is:

Data East USA, Inc. 470 Needles Drive San Jose, CA 95112 Attn: Customer Service Dept.

Be sure to indicate whether you wish to have your name added to our mailing list for service bulletins and product updates. The form below is provided for your convenience

HIPPODROME™ CUSTOMER RESPONSE

COMPANY NAME:

ADDRESS:

CITY: STATE: ZIP:

TELEPHONE:

YOUR NAME: TITLE:

GAME CABINET SERIAL NUMBER

PCB SERIAL NUMBER AAMA # (from Original Product Seal) ADD YOUR COMPANY TO OUR DIRECT MAIL LIST? (circle one) YES NO COMMENTS:

Page 53

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 54

WARRANTY INFORMATION

Data East USA, Inc. (‘Seller’), warrants only to the original purchaser ("Buyer"), of its products that the items listed below are free from defects in material “and workmanship under normat-use and service for the period specified:

GAME LOGIC PRINTED CIRCUIT BOARD(S) 30 DAYS

No other parts of the Seller's products are warranted,

Warranty periods are effective from date Of initial shipment from Seller to Buyer, Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

1, Seller is notified promptly upon discovery by buyer that Stated products are detective.

  • Such products are properly packaged and then returned freight pre-paid, to a place specified by Seller.

This warranty does not apply to products damaged during shipment and/or due to improper handling, or due to improper installation orusage, of alteration. Iino event shall Seller be liable for any anticipated profits, loss of profits, loss of use, accidental or consequential damages, or any other losses incurred by the customer in Connection with the purchase of a Data East USA, Inc., product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER-AND BUYER. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.