World Class Bowling
World Class Bowling (v1.66) (Incredible Technologies, 1995) · Manual · 29 pages · 64 sections · original scan
INSTALLATION MANUAL
it inereviille
World Class Bowling Deluxe
World Class Bowling Deluxe offers players their choice of two exciting Bowling — games! The first is Regulation Bowling and the second is the exciting new Flash — Bowling! E
How to Play Flash Bowling
Bonus values appear at the top of the screen. The numbers light up in sequence.
The flashing numbers stop when the ball hits a pin.
On a strike, the value of the highlighted number is added to the player’s score.
On a strike, the value of the highlighted number is added to the player’s score On a spare, half the value of the highlighted number is added to the player's
score.
To view the bonus values from previous frames, press the start button.
Flash Bowling offers a new element of skill and timing to the game of Bowling, as players try to stop the moving number values as they go for strikes and spares. Try it today!
Table of Contents
1 GETTING STARTED. 5 MAIN SERVICE MENU... 10
GAME PACKAGE CONTENTS ......essscseeeesseeee 2 OPERATOR ADJUSTABLES RECOMMENDED TOOLS AND SUPPLIES......... 2 Game Mode Selection. Game Resets. Attract Mode Soun 2 2 INSTALLATION PREPARATION............ 2 Credit Settings...... 2 Timeout Settings For Each Ball 2 THE CABINET Ticket Dispenser Settings. 2 F Skill Level Adjustment 3 Power Requirements. 2 . Monitor Requirements. 3 Horizontal Screen Adjustments . 3 Cabinet Selection 3 VOLUME SETTINGS Preparing a used cabinet for WORLD CLASS BOWLING THE CONTROL PANEL. Trackball Preparation Button Preparation. THE GRAPHICS OVERLAY GAME AUDITS . Review Audits. SYSTEM TESTS Video Screen Test Sound Tests ..... Player Control Tesi GROM Checksum Tesi Video Ram Test....... Exciter Test....... Voltage Adjust Tesi
APPENDIX A. GENERAL TROUBLESHOOTING Control Panel Overlay Installation . Function Labels Overlay Installation Marquee Installation .........12+++ WIRING AND HARDWARE ASSEMBLY Control Panel Assembly... Printed Circuit Board (PCB) Wire Harnes. Power Wires VIDEO PROBLEMS ..........sccccsssccsesseeeeeneeeeteees 18 Monitor Wires . Speaker Wires SOUND PROBLEMS .......ccccseseeseeseesesseseeneeneenee 19 CONTROL PROBLEMG.........cccccccssesseeesesneeneeees 20 Coin Doors, Test Switch and Service Button POWER-UP PROBLEMG...... ooo BHDOMDANNN NOD OM HA WW
Wiring Ticket Dispenser Installati MISCELLANEOUS PROBLEMS... Final Check APPENDIX B 3 INITIAL START-UP 9 JAMMA HARNESS CONNECTION. JAMMA HARNESS CONNECTION.........-c:e0 24
TRACKBALL CABLE CONNECTION... 24 4 DIP SWITCH SETTINGS .....00.....::scc000 10 APPENDIX C 1/0 and JAMMA SCI
APPENDIX D WARRANTY INF‘
GETTING STARTED
GAME PACKAGE CONTENTS
- Printed Circuit Board (PCB) Assembly
- Trackball Assembly w/Metal Plate
- Trackball Cable Assembly
- Button Assemblies
- Marquee Styrene
- Marquee Plexiglas
- Control Panel Overlay
- Set of Function Labels
- Manual
RECOMMENDED TOOLS
AND SUPPLIES
Phillips and Slotted Screwdrivers Socket Set Wire Cutters and Strippers Pliers or Channel Locks Electric Drill with 3/32”, 4”, and 7/16” Bits 4-3/16” Chassis or Sheet Metal Punch Small File Razor Knife and Sharp Blades Straight Edge Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Heat Shrink Tubing (3/32”, 1/8”, and 3/16”) Masking Tape 3-1/2" or 4” Wire Ties
IF YOU DO YOUR OWN PAINTING, YOU'LL NEED THESE PAINT SUPPLIES: ¢ Air Brush or Paint Sprayer Paint Roller and Pan Paint Brush Paint (and Primer) Sandpaper Putty Knife and Wood Putty eee ee
2- WORLD CLASS BOWLING
INSTALLATION PREPARATION
eel
BEFORE YOU START.....
1. Check to see if all the needed parts have been included in your kit (See GAME PACKAGE CONTENTS.)
Do you have the necessary tools? (See RECOMMENDED TOOLS AND SUPPLIES.)
Do not work with any part of the system plugged in (lights, monitor, or power supply).
E CABINE
POWER REQUIREMENTS
Make sure the game you have chosen to convert is able to supply all the required voltages for WORLD CLASS BOWLING.
The output level of many “regulated” switching power supplies actually vary with load. For this reason, the power supply from an old game may not be correctly adjusted for WORLD CLASS BOWLING. This makes the existing power supply inappropriate and hazardous to your new game. Therefore, it is very
MONITOR REQUIREMENTS
WORLD CLASS BOWLING requires a low-res monitor in a horizontal mount raster scan with positive or negative composite SYNC. It can be difficult to change the monitor from vertical to a horizontal unit, therefore, installation will be easier if you choose a horizontal mount cabinet.
CABINET SELECTION
You can choose either a new cabinet or a used cabinet for your WORLD CLASS BOWLING game. Reusing a cabinet is by far the most cost-effective way to maximize the return of your initial investment. In either case, all you need to provide is the cabinet with a power supply and monitor. We provide the rest. The end result is a new game at a very low cost.
It is recommended that a large control panel with a 25” monitor, like those on a 4-player cabinet, be used for your WORLD CLASS BOWLING.
When selecting a cabinet, keep this in mind: A cabinet with a 25” monitor and a large control panel will allow you to mount the trackball farther from the monitor. This prevents players hands from hitting the monitor glass when rolling the trackball forward, and will earn better than a smaller control panel with a smaller monitor.
PREPARING A USED CABINET FOR WORLD CLASS BOWLING
- Remove the following from the cabinet:
- Main Logic Board(s)
- Control Panel
- Monitor Plexiglas
- Marquee
- Cabinet Graphics
- Thoroughly clean out your cabinet. Remove all the old buttons, joysticks and wires from the control panel. DO NOT remove monitor and speaker wires.
- Remove the old graphics and adhesive from the control panel, and the side of the cabinet. Remove adhesive with solvent.
- Fora fresh look, painting is highly recommended. Spray painting gives a better finish, but if an air brush or paint sprayer is unavailable, a roller is second best. Remember to cover all exposed surfaces not to be painted.
- Remember, spending time on the cabinet’s appearance (i.e., marquee, control panel, and cabinet graphics) will raise your profits with the introduction of a new game package, especially if the cabinet looks clean and new.
- The “new game look” should always apply to the inside of your game as well. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies, and a sweep with the vacuum cleaner will ensure that glitches do not occur.
THE CONTROL PANEL
Mounting the trackball correctly and securely is very
Installing the trackball and overlay as far away from the glass as possible will prevent players hands from hitting the monitor glass when rolling the trackball forward. Also the trackball should be centered on the control panel for best results.
TRACKBALL
START BUTTON
LEFT Ri BUTTON BUTTON
CONTROL PANEL LAYOUT (TRACKBALL MUST BE CENTERED ON THE CONTROL PANEL)
WORLD CLASS BOWLING - 3
TRACKBALL PREPARATION
When making the hole for the trackball, follow the instructions
starting on this page and the next, N g
for the type of control panel you ch . i |
- Fill any existing holes in the metal control panel. will be using.
- Place and secure TEMPLATE #1 to your control
- Carefully drill the holes for the ball and the 0 — - mounting bolts using the template as a guide. MONITOR 4, Remove template and file down any rough edges. 2.16" Meuning Holes ee
- See THE GRAPHICS OVERLAY section on page 6 on how to install the graphics. ° seacrban Assent) |
| 6. Mount trackball under the metal control panel using the four carriage bolts.
| NOTE: Be sure the trackball is mounted as shown in the diagram on page 4.
| | NOTE: The supplied metal plate is not needed with i metal control panels. Ee = PLAYER NOTE: Be sure to mount the trackball so as much of
- IMPORTANT: the ball is exposed as possible. Poston tne tractbal 38 fax away Hom the manor a8 poxseie fe cure too rebate mounted bragrt and wn he correct anetat0n
- Securely fasten the trackball grounding wires to TRACKBALL ORIENTATION Field Ground in your cabinet. This step is (NOT-DRAWN TO.SCALE) important in reducing static buildup and discharge caused by the trackball.
IMPORTANT!: 8. If using Plexiglas on your control panel, it is
‘The supplied trackball comes equipped with a highly recommended that a 3-1/2" hole be cut in grounding cable. This cable must be connected to the Plexiglas for the trackball. This allows for field ground to protect the trackball P.C. boards from players to use the full height of the trackball. becoming damaged by electro-static discharge. Carefully file and smooth the edges of the hole in the Plexiglas so players do not cut their hands when playing.
SE 4- WORLD CLASS BOWLING
To mount trackball to a wooden control panel with routing capability use TRACKBALL MOUNTING TEMPLATE #2
- Fill any existing holes in the wooden control panel.
- Place and secure TEMPLATE #2 to your control panel in the desired location.
- Carefully cut the hole for the trackball in the shape indicated on the template.
- Drill the mounting holes indicated.
- Next route out the shaded area indicated on TEMPLATE #2, 1/16” deep. Use a 1/2” Rabbiting Bit for best results. This is so the supplied metal plate will be flush with the control panel surface.
- Remove template and file down any rough edges.
- See THE GRAPHICS OVERLAY section on page 5 on how to install the graphics.
- Mount trackball to the metal plate using the four carriage bolts supplied. Then mount the metal plate to the wooden control panel.
- Securely fasten the trackball grounding wires to Field Ground in your cabinet. This step is
- If using Plexiglas on your control panel, it is highly recommended that a 3-1/2” hole be cut in the Plexiglas for the trackball. This allows for players to use the full height of the trackball. Carefully file and smooth the edges of the hole in the Plexiglas so players do not cut their hands when playing. To mount trackball to a wooden control panei without routing capability use TRACKBALL MOUNTING TEMPLATE #3
- Fill any existing holes in the wooden control panel.
- Place and secure TEMPLATE #3 to your control panel in the desired location.
- Carefully cut the hole for the trackball in the shape indicated on the template. The trackball should fit the hole shape exactly.
- Drill the mounting holes as indicated.
- Remove template and file down any rough edges.
- Using the TRACKBALL ORIENTATION TEMPLATE, cut a 3” hole in the Plexiglas overlay to fit over the trackball. Be sure to include holes for the buttons, and all of the mounting bolts.
- See THE GRAPHICS OVERLAY section on page 5 on how to install the graphics.
- Insert the trackball into the newly cut hole. Place Plexiglas overlay on top of the control panel. Place the supplied metal plate under the trackball and use the carriage bolts to secure it to the control panel. The metal plate below and the Plexiglas above will secure the trackball assembly into position.
- Securely fasten the trackball grounding wires to Field Ground in your cabinet. This step is
WORLD CLASS BOWLING - 5
BUTTON PREPARATION
- When making the holes for the buttons, use the labels as a guide to where you want to drill your new holes, and then cut a 1” hole in the center of where the labels are to be placed. DO NOT stick the labels to the panel at this time.
- Drill or punch the holes marked for buttons or bolts. Use a chassis or sheet metal punch for best results on button holes.
- Use a file to smooth any rough edges on the holes.
- Fill any old and unused holes with wood, resin, or a metal plate.
- It is recommended that you cover your control panel with Plexiglas. Now would be a good time to cut it to fit while the dimensions and tools are at hand.
THE GRAPHICS OVERLAY
WORLD CLASS BOWLING comes equipped with graphics that will accommodate a variety of existing game cabinets.
CONTROL PANEL OVERLAY
INSTALLATION
- Make sure the control panel is clean and free from dust, grease, metal filings, and sawdust. Your control panel should be painted white, with all holes filled for optimal results. The background overlay provided with the game is oversized to accommodate most control panel sizes. Be sure to leave enough excess material above and below the control panel in order to trim it evenly.
- Remove the protective backing from the overlay. Center the overlay over the control panel and place down gently, making sure to keep it square. Using your hands, press down firmly, starting from the center and smooth the overlay outward, making sure all bubbles have been pressed out for a clean, flat surface.
6 - WORLD CLASS BOWLING
- Using a sharp razor knife, trim any excess from the overlay. Carefully pierce through the overlay above each control panel hole that you have marked. Cut out material covering the pre-drilled holes with the razor knife. Be sure to cut the overlay above each hole and trim cleanly and evenly.
FUNCTION LABELS OVERLAY
INSTALLATION
Line up the supplied function labels with the corresponding control panel holes. Remove the backing and carefully press into place. Be sure they are straight. Refer to the diagram below.
FUNCTION LABELS LAYOUT
MARQUEE INSTALLATION
Using the marquee glass as a template, center the it on your new marquee graphics, making sure that all the printed images will be visible. Using a razor knife, score the new marquee deeply, following the edges of the old glass. Carefully break off the styrene. Be sure the light behind the marquee works and that the glass is clean on both sides. Now install the marquee graphics and glass securely.
POWER WIRES
Connect the wires that are designated for your power supply. You will need a supply of +5 vde, and +12 vdce. The +5 vde must be regulated to within 5% (+ or - 0.25. The +12 vde may be unregulated but should not stray too far or the sound may be affected. If the cabinet’s supply does not provide these voltages, it will have to be replaced. A switching-type supply is recommended.
Ly You will notice that you have more than one wire for each voltage. Use all wires supplied on the harness. This will ensure better power transmission and prevent overloading of the edge connector pads.
Tin all power supply wires before connecting them to the power supply. Loose strands may short out the supply. For best results, connect spade lugs to the ends of the power wires and attach to the screw terminals of the power supply.
MONITOR WIRES
You will be connecting the RED, GREEN, and BLUE video drives along with the composite SYNC and video GROUND wires.
SPEAKER WIRES
Connect the speaker wires paying attention to their polarity.
If your cabinet has two speakers, connect both. If they are 8 or 16 ohm speakers, connect them in parallel, if they are 4 ohm, connect them in series.
8 - WORLD CLASS BOWLING Position speakers as far from the monitor as possible. If placed too close, the speaker's magnet may deflect the monitor and cause strange coloration, which can usually be corrected by degaussing the monitor. Make sure everything else in the cabinet is attached securely for the same reason.
SYNC
This is the recommended approach for a Wells- Gardener monitor and should work with others as well.
If your monitor does not have a composite SYNC input but has separate horizontal and vertical SYNC inputs, try connecting the composite SYNC signal from the PCB to the negative horizontal SYNC signal on the monitor. This should produce a satisfactory result, although some adjustment of the monitor's SYNC controls may be necessary.
Coin Doors, TEST SWITCH AND
SERVICE BUTTON WIRING
- Wire the coin doors and the test / service switch(es) as per the JAMMA Harness Connection table on page 23.
- Connect the door lamps to the +12 vde supply. Some games have separate power supply outputs for the lamps.
- Install a test switch somewhere convenient inside the coin door area. This switch allows you to enter adjustables, run diagnostics, and see or clear audits. Make it readily accessible through the coin door. Wire it to the Test wire on the JAMMA Harness.
- Install a service switch (not included) somewhere convenient inside the coin door area. This switch allows you to give credits to players without affecting the game's credit audits or coin meters. Example: A player puts in a coin and gets no credit, the operator can then push the service button and a credit is given to the player without affecting the game's audits and coin meter.
- Clean and lubricate your coin mechs.
TICKET DISPENSER INSTALLATION
This game is capable of dispensing tickets through a Deltronics DL-1275 or similar ticket dispenser. Connection is through the 4-pin Molex plug at the right edge of the Main board marked “TICKET”. Itis pinned out as follows:
PIN FUNCTION 1 Ticket Sense 2 = Ground 3 Motor Enable 4 +12vde
This is the same pin out (with a different connector) as the Deltronics DL-1275. If you wish to connect a ticket dispenser to this game you will have to make a cable with the proper connectors. The DL-1275 mates with a Molex #03-09-1041 or #03-09-1042. The game board connector mates with a Molex #22- 01-2047 or #22-01-3047. Simply connect pins 1 through 4 on one end directly to pins 1 through 4 on the other end. If the ticket dispenser is not a DL- 1275 you may need a different cable. Other electromechanical devices can be connected through this connector provided they use the same signals. The Motor Enable output is TTL-compatible and is high when the motor is turned on. The Ticket Sense input expects an open-collector TTL signal where low indicates the sensor is not blocked. When a ticket is to be issued, the Motor Enable line goes high until either the Ticket Sense line goes high then low again (indicating a ticket has passed) or until about 1/3 of a second passes (meaning dispenser is empty or jammed).
FINAL CHECK
- Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.
- Make sure the coin door is tight and the coin mechs are well adjusted.
- Make sure all assemblies are firmly attached. Anything that is not mounted securely will rattle when the game is played. This game makes use of low-frequency sounds which can cause any loose joints to rattle.
INITIAL START-UP
Attach the JAMMA Harness. Plug in the game and turn it on.
Make sure the harness is plugged in correctly. Damage to PCB will occur if JAMMA connector is plugged in wrong.
Look and smell for smoke (TURN IT OFF IMMEDIATELY IF ANY IS NOTICED).
Use the Voltage Test screen to adjust your power ‘supply. When the screen says “Voltage OK”, your power supply is properly adjusted to 5.2 volts on the PCB. Adjust the +5 Volt supply so that you read 5.2 Volts across an |.C. on the circuit board. If measured at the power supply, the reading will be higher at the power supply outputs.
Make sure the green and yellow LED on the PCB is flashing. If not, something is wrong, turn off the game.
Listen for sound. Sounds should be heard in the attract mode.
If you do not hear any sounds and the yellow LED is flashing, try turning up the volume and check the speaker connections. Dropping a coin through a coin switch should cause a sound.
How is the picture? Is it centered or is it too bright or too Is it in focus? Adjust your monitor to get the best picture possible.
Check your monitor manual to make adjustments. Some test patterns are available through the game's system tests by pressing the Test switch. Use them when making any adjustments. (See SYSTEM TESTS information on page 14. Proper monitor adjustment is very important.)
WORLD CLASS BOWLING - 9
COLOR KEY NOTE:
For easy identification, all test screens have been color coded. Items displayed in GREEN are the Menu titles. This is the name of the menu that is currently displayed. Items appearing in YELLOW are the menu's instructions. The BLUE items are choices available in this menu. The WHITE item is the selection that is currently highlighted. If RED is ever displayed, there is a problem with that item and it should be corrected.
OPERATOR ADJUSTABLES
The OPERATOR ADJUSTABLES MENU is accessed through the MAIN SERVICE MENU. From the MAIN SERVICE MENU, move the trackball down to highlight the words OPERATOR ADJUSTABLES MENU which will then appear in white letters. Now press the START button, and the OPERATOR ADJUSTABLES MENU will appear on the screen.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE.
OPERATOR ADJUSTABLES MENU | EXIT ADJUSTABLES
GAME MODE SELECTION
GAME RESETS
ATTRACT MODE SOUNDS
CREDITS SETTINGS
TIMEOUT SETTINGS FOR EACH BALL
TICKET DISPENSER SETTINGS
SKILL LEVEL ADJUSTMENT
HORIZONTAL SCREEN ADJUSTMENT
OPERATOR ADJUSTABLES MENU
As you can see, there are many possible customizing procedures that you can control. Below is a brief description of each adjustable function and what the screen looks like when displayed. Remember, to select an item from any menu, using the trackball to highlight the item in white, and then press the START button. GAME MODE SELECTION
This menu allows you to place the game in standard COIN MODE, or choose FREE PLAY.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
GAME MODE SELECTION
COIN MODE
FREE PLAY
GAME MODE SELECTION SCREEN
In COIN MODE, the game will only work if coins are deposited into the game.
In FREE PLAY, coins are not needed for play, and the START button is always active.
The GAME RESETS menu will cancel or zero out any custom features or bookkeeping figures that are no longer wanted.
WORLD CLASS BOWLING V1.00
MOVE TI ALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
EXIT RESETS
RESET ALL TO FACTORY SETTINGS
RESET HIGH SCORES ONLY
RESET AUDITS ONLY
GAME RESETS MENU
RESET ALL TO FACTORY SETTINGS will change the game back to the way the game was preset when new. Any custom features such as Free Play and Skill Levels will be changed back to the original settings set at the factory.
RESET HIGH SCORES ONLY is used to erase all of the high scores stored in memory.
RESET AUDITS ONLY is used when all of your bookkeeping and statistics have been gathered from the Audits section, and are no longer needed. If you like to gather all of your accounting information each week, or after each collection, it is a good practice to reset all of the audits so your coin count will match the audit information.
WORLD CLASS BOWLING - 11
ATTRACT MODE SOUNDS
This menu is used to adjust the sounds that are heard while no one is playing the game.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
ATTRACT MODE SOUNDS:
ALL ATTRACT MODE SOUND:
OCCASIONAL ATTRACT MODE SOUNDS
ALL ATTRACT MODE SOUNDS ON
ATTRACT MODE SOUNDS MENU
ALL ATTRACT MODE SOUNDS OFF will not allow any sounds to be played during the attract mode.
OCCASIONAL ATTRACT MODE SOUNDS plays sounds about every ten to twelve times the attract mode is repeated.
ALL ATTRACT MODE SOUNDS ON will play sounds during every attract cycle.
CREDIT SETTINGS
This menu allows you to change the number of coins needed to play WORLD CLASS BOWLING.
WORLD CLASS BOWLING V1.00
M RACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE | CREDIT SETTINGS
EXIT CREDIT SETTINGS | DOOR 1 CREDITS PER COIN | Doon 2 CREDITS PER COIN | COINS NEEDED To START TO CHANGE VALUES. MOVE TRACKBALL LEFT TO DECREASE /E TRACKBALL RIGHT TO INCREASE
CREDIT SETTINGS SCREEN
You can set each door to different coins values by highlighting : DOOR 1 CREDIT PER COIN for coin door 4, DOOR 2 CREDITS PER COIN for coin door 2. Moving the trackball left or right will change the number of credits that each coin represents.
COINS NEEDED TO START.....To award a game credit, the player will need to insert an adjustable number of coins.
12 - WORLD CLASS BOWLING
TIMEOUT SETTINGS FOR EACH BALL
This option allows for changing the time a player has to throw his next ball before a foul is called.
WORLD CLASS BOWLING V1.00
KBALL UP AND DOWN TO SELECT,
‘SECOND TIMEOUT
SEC SECOND TIMEOUT NO TIMEOUT SNOMaeNS
TIMEOUT SETTINGS FOR EACH BALL SCREEN
Highlight the desired time and press the START button to choose and exit.
TICKET DISPENSER SETTINGS
WORLD CLASS BOWLING V1.00
|) TICKET DISPENSER SETTINGS
EXIT TICKET SETTINGS
TURN TICKETS ON OR OFF ON/OFF
Tc sPENSED FOR EVERY 60POINTS 4
TICKETS FOR BEER FRAME STRIKE a
TICKETS FOR PERFECT GAME
TO CHANGE VALUES ‘TRACKBALL LEFT TO DECREASE ‘TRACKBALL RIGHT TO INCREASE
WORLD CLASS BOWLING is capable of dispensing tickets through a standard ticket dispenser.
To turn this feature ON or OFF, highlight TURN TICKETS ON OR OFF by rolling the trackball up and down. Rolling the trackball left and right will change the ON and OFF settings.
To adjust the number of tickets dispensed, highlight TICKETS DISPENSED FOR EVERY 60 POINTS. Roll the trackball left or right to adjust the number of tickets appropriate for your location.
You can reward tickets for special events in the game. TICKETS FOR BEER FRAME STRIKE will dispense the desired number of tickets in frame 5 of each game if a player strikes.
TICKETS FOR PERFECT GAME dispense the desired number of tickets to a player who makes all strikes. To turn these features off, set the number to zero.
SKILL LEVEL ADJUSTMENT
WORLD CLASS BOWLING allows for changing the level of skill needed to play the game. This feature is good for locations with younger or novice players who are less skilled at the game, or expert or accomplished players who demand a greater challenge.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
SKILL LEVEL ADJUSTMENT
SKILL LEVEL 1
SKILL LEVEL 2 SKILL LEVEL 4
SKILL LEVEL 3
SKILL LEVEL 5
EASIEST
HARDEST
SKILL LEVEL ADJUSTMENT SCREEN
To set the game to an easy skill level, highlight...... SKILL LEVEL 1 - EASIEST.
To set the game to a difficult skill level, highlight...... SKILL LEVEL 5 - HARDEST.
SKILL LEVEL 2, SKILL LEVEL 3, SKILL LEVEL 4 are settings between the easiest and hardest levels. Sometimes it is best if the skill level is adjusted gradually over a period of time.
HORIZONTAL SCREEN
ADJUSTMENTS
If the picture on your cabinet is not centered properly, you may be able to adjust it from this menu.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SI PRESS START TO CHOOSE |
HORIZONTAL SCREEN ADJUSTMENT
‘SCREEN AD. a LEFT MOST
REEN ADJUST
REN ADJUST CENTER
-REEN ADJUST
SCREEN ADJUST RIGHT MOST
HORIZONTAL SCREEN ADJUSTMENT
SCREEN ADJUST -1 LEFT MOST will move the picture far to the left.
SCREEN ADJUST -3 CENTER will attempt to center the picture on the video monitor.
SCREEN ADJUST -5 RIGHT MOST will move the picture far to the right.
E SETTINGS
The VOLUME SETTINGS screen is used to adjust the sounds that are heard during game play.
TO EXIT PRESS START
/E TRACKBALL RIGHT TO INCREASE VOLUME MOVE TRACKBALL LEFT TO DECREASE VOLUME
VOLUME SETTINGS SCREEN
When this screen appears, music will play. Move the trackball to the right to increase the game’s sounds and music. Rolling the trackball to the left will make the game sounds softer. When you have adjusted the sounds to the appropriate volume, press the START button to exit back to the main menu.
GAME AUDITS
The GAME AUDITS MENU will supply you with a detailed accounting of helpful and informative bookkeeping and statistics. To enter THE GAME AUDITS MENU, first go to the MAIN SERVICE MENU by pressing the test switch located just inside the coin door of the cabinet or flip DIP switch 1 to the ‘OFF’ position on the Main PCB. From the MAIN SERVICE MENU, use the trackball to highlight the GAME AUDITS MENU. Now press the START button, and the GAME AUDITS MENU will appear on the screen.
WORLD CLASS BOWLING V1.00
BALL UP AND DOWN TO SELECT, RT TO CHOOSE
GAME AUDITS MENU
EXIT AUDITS,
REVIEW AUDITS
RESET AUDITS
GAME AUDITS SCREEN
WORLD CLASS BOWLING - 13
REVIEW AUDITS
When you choose to review the coin audits, the REVIEW AUDITS screen will appear.
WORLD CLASS BOWLING V1.00
PRESS START TO EXIT
REVIEW AUDITS SCREEN
COIN DOOR 1 COINS
COIN DOOR 2 COINS
TOTAL COINS
ONE PLAYER GAMES
‘TWO PLAYER GAMES | THREE PLAYER GAMES
FOUR PLAYER GAI | TOTAL GAMES STARTED
AVERAGE GAME SCORE XX
AVERAGE GAME TIME
REVIEW AUDITS SCREEN
COIN DOOR 1 CREDITS and COIN DOOR 2 CREDITS show the total coins that have passed through the individual coin mechs.
TOTAL COINS shows the total amount of coins entered into the game.
ONE PLAYER GAMES, TWO PLAYER GAMES, THREE PLAYER GAMES, and FOUR PLAYER GAMES display the number and type of games played. TOTAL GAMES STARTED shows the total number of games started.
AVERAGE GAME SCORE is calculated by totaling all of the final game scores and dividing by the number of games started.
AVERAGE GAME TIME shows the average time it takes to complete a single game.
AVERAGE TICKETS DISPENSED shows the average number of tickets given out during game play. TOTAL TICKETS DISPENSED displays the actual number of tickets given out.
14 - WORLD CLASS BOWLING RESET AUDITS
This menu will reset your audits.
WORLD CLASS BOWLING V1.00
TRACKBALL UP AND DOWN TO SELECT,
RESET AUDITS
NO RESET AUDITS
| RESET AUDITS L GAME RESETS SCREEN
If you wish to set all of the game audits (described above) back to zero, highlight RESET AUDITS from this menu and press the START button. The screen will briefly display AUDIT RESET.
If you change your mind and decide not to reset the audits to zero, highlight NO RESET AUDITS and you will exit this screen without making any changes.
SYSTEM TES
WORLD CLASS BOWLING has been inspected and tested at the factory, and most likely the game will be in perfect working order when you plug it in. If you are experiencing any problems with the game, the SYSTEM TESTS MENU is a good place to start when tracking down the problem. To enter the System Tests Menu, first go to the Main Service Menu by pressing the test switch located just inside the coin door of the cabinet, or set DIP Switch 1 on the Main PCB to the ‘OFF’ position. From the Main Service Menu, move the trackball until the word SYSTEM TESTS MENU appears in white letters. Now press the start button, and the System Tests Menu will appear on the screen.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
SYSTEM TESTS MENU
EXIT TESTS
VIDEO SCREEN TESTS
‘SOUND TESTS
PLAYER CONTROL TESTS
GROM CHECKSUM
VIDEO RAM TEST
EXCITER TES! VOLTA‘ M
SYSTEM TESTS MENU
VIDEO SCREEN TEST
You can test your monitor and adjust colors by choosing VIDEO SCREEN TEST and pressing the START button.
WORLD CLASS BOWLING V1.00
VIDEO SCREEN TEST
TO VIEW VIDEO TEST SCREENS
PRESS HOOK LEFT OR RIGHT BUTTONS PRESS START AT ANY SCREEN TO EXIT
FOLLOWING ENS ARE AVAILABLE
LOR ADJUSTMENT CREEN GRID PATTERN RED SCREEN
BLUE SCREEN WHITE SCREEN
VIDEO SCREEN TEST MENU
When the HOOK LEFT or HOOK RIGHT buttons are pressed, the screen changes to display a grid of colored rectangles. Use these colors as a guide and adjust your monitor so they look as good as possible. This test can be exited at any time by pressing the START button.
SOUND TESTS
Choose SOUND TEST from the SYSTEM TEST MENU to test the sounds and speakers in the game. The sound section also controls the coin meter, and you can test it from this section as well.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
EXIT SOUND TEST
| SROMO
SROM 1
ROMO —- DRUMS
MUSIC
COIN METER TEST
TEST ALL SOUND ROMS
1 TICKET
SOUND TESTS SCREEN
To test the coin meter, choose COIN METER TEST from this menu. If everything is working properly, the meter should increment each time the START button is pressed while this line is highlighted.
To test the ticket dispenser, highlight DISPENSE 1 TICKET from this menu. A ticket should be dispensed when the START button is pressed. PLAYER CONTROL TEST
When PLAYER CONTROL TEST is selected, the screen will display a diagram of a typical WORLD CLASS BOWLING control panel. The controls are highlighted on the diagram when the controls are active. Test all of the controls, including coin test and service switches. Press HOOK LEFT and HOOK RIGHT together to exit this test.
PLAYER CONTROL TEST SCREEN
GROM CHECKSUM TEST
Choose GROM CHECKSUM TEST from the SYSTEM TEST MENU to test the Graphics chips on the PCB. This test performs a complete test of the Graphics ROM’s. While the test is in progress the following message is displayed:
ECONDS TO FINISH |
GROM CHECKSUM TEST SCREEN (TEST IN PROGRESS) When the test is completed the GROM Test Screen is displayed.
WORLD CLASS BOWLING V1.00
GROM CHECKSUM TEST: (PASSED or FAILED)
PRESS START BUTTON TO EXIT
GROM CHECKSUM TEST SCREEN (TEST COMPLETED)
- If all checksums are shown in blue, the test passed and your game is in good working order.
- If any checksums are bad, they will be displayed in red text on this screen. This means that the GRON is defective and needs to be replaced.
- To exit this test, press the START button.
VIDEO RAM TEST
WORLD CLASS BOWLING - 15
This test performs a complete test of the Graphics Video RAM. When the test is completed the results will be displayed as follows.
WORLD CLASS BOWLING V1.00
VIDEO RAM TEST
VIDEO RAM FIRST PAGE STATUS = 0000
VIDEO RAMTEST ——_[PASSED or FAILED]
PRESS START TO EXIT ———_}
VIDEO RAM TEST SCREEN
- If the game passes this test, zeros will be displayed in white along with a “VIDEO RAM TEST PASSED” message..
- If the test fails, a non-zero status and “VIDEO RAM TEST FAILED” message will be displayed in red. Call your distributor or Incredible Technologies, Service Department for further help.
- To exit this test, press the START button.
EXCITER TEST
This test performs a video and audio test of all the exciters in the game.
WORLD CLASS BOWLING V1.00
MOVE TRACKBALL UP AND DOWN TO SELECT, PRESS START TO CHOOSE
| excrreR TEST
EXIT EXCITER TEST
SELECT EXCITER NUMBER(1-29) XX
TO CHANGE VALUES MOVE TRACKBALL LEFT TO DECREASE MOVE TRACKBALL RIGHT TO INCREASE
EXCITER TEST SCREEN
You can view and test all of the exciter graphics from this menu. Move the trackball left and right to change the exciter number and press START to play the exciter. Check for any graphics and sound problems as they are displayed.
VOLTAGE ADJUST TEST
16 - WORLD CLASS BOWLING When the VOLTAGE ADJUST TEST is selected, the screen will display the history of how the voltage has been and how the current voltage is now. Adjust your voltage until you read voltage is OK.
GOLDEN TEE 3-D GOLF V1.00
PRESS START TO EXIT VOLTAGE HISTORY IS SET TO OK ON EXIT
VOLTAGE ADJUST TEST
| HistoRY: VOLTAGE HAS BEEN OK
RIGHT NOW:
VOLTAGE ADJUST TEST SCREEN
VIDEO PROBLEMS
Symptom ae | (Co Probetie Cause Solution Gees —_]
No picture
Scrambled Picture
Missing colors or a washed out color
Bright, blurry, or rolling picture
Picture too large, too small, or off center
Video image is flipped
Bad images in picture
Diagonal white lines
18 - WORLD CLASS BOWLING Check Dip switches.
Bad connections
Monitor
JAMMA harness connected improperly
Missing sync connection or misadjusted monitor
Bad video connections
Misadjusted monitor
Misadjusted monitor
Misadjusted Monitor
Bad GROM
GND problem SW1-Dip switches 1 thru 4 must be
SW2-Dip switches 1 and 2 must be “ON”, and 3 and 4 must be ‘OFF’
Make sure there are good connections from the board's video outputs to the monitor's video inputs.
Make sure the monitor is operating correctly. (Check it with another compatible logic board.)
Identify Pin 1 on the JAMMA connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.
Check the sync connection - Adjust monitor
Check the video red, green, and blue connections.
Adjust the monitor, not the board. (Refer to your monitor manual.)
Adjust the monitor, not the board. (Refer to your monitor manual.)
Reverse the monitor's convergence wires or flip the monitor 180°. (Refer to your monitor manual.)
Do GROM test. Check IC pins to make sure none are bent over.
Earth and Logic GND's should be connected at the power supply.
SOUND PROBLEMS
Symptom [Probable Cause _—| [ Solution __| No Sound +12v power supply is bad Try another +12v power supply.
Bad connection to the board Check for +12v power on the board.
Check for +5v power on the board.
Check the volume setting in the OPERATORS ADJUSTABLE section of the Operators Mode.
Check the speaker connections.
JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.
Miscellaneous Make sure the sound status light is flashing on the board.
WORLD CLASS BOWLING - 19
[Frobabie Gauze | [Sottion Symptom
| Buttons do not work or are | Switches not properly | Make sure that the common post of |
| partly inoperable. Or the | connected | the switch is connected to ground. |
selections keep scrolling on Operator Mode menus. Make sure each individual switch is working by doing the Control Panel Test found in the SYSTEM TESTS section.
Make sure that the signal wire for that particular switch is connected to the normally open post of the switch.
JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.
| Coin counter not working | Miscellaneous | Make sure that the signal wire has |
aconnection from the switch to the board.
Make sure +12v is hooked up to the counter.
The signal wire is not connected to coin counter. (Check continuity).
Verify that the counter is good.
| Trackball does not work | No +5 voltage | Bad inductor(L7) or bad connection |
to trackball.
The supplied trackball comes equipped with a grounding cable. This cable must be connected to field ground to protect the trackball P.C. boards from becoming damaged by electro-static discharge.
20 - WORLD CLASS BOWLING
CO
POWER-UP PROBLEMS
Symptom [Probable Cause [Solution No reaction when game is Voltage to high Power supply is too high. Power turned on should be between +5v & 5.2v. (Measured on the circuit board).
Cabinet is not connected to earth ground. (All metal should be connected to the earth ground).
Short between power and ground. Check for foreign material.
Disconnect the harness and measure the resistance between power and ground. It should read around 600 ohms. (0 ohms is a dead short).
Make sure the harness is not shorting to anything, such as bare or frayed wires shorting out each other or hitting bare metal.
No power from the power Replace power supply. supply
Power supply too low. (Should ideally be between +5v & +5.2v). (Measured on the circuit board). Power supply
Check for loose or foreign material on the board. Short on the board
JAMMA harness connected Identify Pin 1 on the JAMMA improperly connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred.
Check for bent pins on socketed parts. Screen flashes repeatedly Open on socketed IC's
Make sure that all IC's are seated in their sockets properly.
Check voltage. (Measured on the circuit board). +5v setting too low
SW2 Dip switches near the Make sure SW2-Dip switch #1 and green LED may not be set # 2 are “ON”, and #3 and #4 are correctly. “OFF”.
WORLD CLASS BOWLING - 21
MISCELLANEOUS PROBLEMS
|| ee | | Green L.E.D. not blinking
Operator adjustables keep changing
Sounds bad
Game comes up in Test Mode
Screen is frozen with an image on the screen.
22 - WORLD CLASS BOWLING Program not running
Bad connections
Loose pin on ASIC (U1)
Low battery voltage
Bad static RAM (U50)
Miscellaneous
Dip Switch 1 is “OFF”
Dip Switch 2 is “OFF” Make sure all socketed I.C.'s are seated correctly. Look for bent pins.
Make sure you have continuity from PCB to power supply.
Call Incredible Technologies, Inc.
Battery should be 2 to 3 volts.
Replace.
Check the speaker connections.
Make sure SW1-Dip Switch 1, near the JAMMA, is in the “ON” position.
Make sure SW1-Dip Switch 2, near the JAMMA, is in the “ON” position.
APPENDIX B
WORLD CLASS BOWLING - 23
JAMMA HARNESS CONNECTION
WIRE COLOR _ _ SOLDER SIDE _ Black GND Black GND. Red +5 vde Red +5 vde
Orange | +12vde KEY
Yellow-Green [Lett Speaker (-)
Green-Black Video Green White Video Sync Orange-Black Service
Green-Blue Coin2
Black GND Black GND. Orange KEY Coin Counter [Red-Green
Left Speaker (+) _| Yellow-Red
Video Red Red-Black Video Blue Blue-Black | im Video GND White-Black
Test Blue
Coin 1 Red-Blue Start 1 Red-White
Player - Hook Left Brown-White Player - Hook Right _| Yellow-White
Coin 3 Gray-White
GND Black GND. Black
TRACKBALL LE CONNECTION
Memory Board Connector Trackball Connector
PIN WIRE #6 - PIN WIRE #1 - Black
PIN WIRE #1 - PIN WIRE #2 - Red |
PIN WIRE #2 - Yellow PIN WIRE #3 - Yellow
PIN WIRE #3 - Green PIN WIRE #4 - Green
PIN WIRE #5 - Blue PIN WIRE #5 - Blue
PIN WIRE #4 - Purple PIN WIRE #6 - Purple
24 - WORLD CLASS BOWLING
APPENDIX C
WORLD CLASS BOWLING - 25
,
me
NOWOS WNNVE ® 0/1
26 - WORLD CLASS BOWLING
APPENDIX D
WARRANTY INFORMATION
WARRANTY, REPAIR AND RETURN POLICY 90-day warranty on all electronic components. All warranty periods begin on the date of purchase from Incredible Technologies, Inc. There is a minimum $55.00 service charge for all non-warranty repairs or returns. For all servicing, return to Incredible Technologies, Inc. ANY non-factory repair or attempted repair voids warranty.
RETURN MERCHANDISE AUTHORIZATION
All returned merchandise must have a Return Merchandise Authorization (RMA) number marked clearly on the outside of the package.
- You must obtain all RMA numbers from your authorized Incredible Technologies distributor. Please have your Incredible Technologies serial number available when calling for an RMA number. + Merchandise returned without an RMA number will not be accepted + Advance replacement boards will be shipped to distributors or, at the distributor's request, will be shipped directly to the operator. + Advance replacement boards will be billed to the distributor until Incredible Technologies, Inc. receives the returned board, at which time a credit will be issued. + Allrepairs and/or replacements will ship as soon as possible after receipt or request (subject to availability)
If the original purchaser discovers any physical defect in the media (disk, EPROM, tape) on which the software is distributed or in the documentation, which in the opinion of Incredible Technologies, Inc. (IT) prevents the product from being used as reasonably intended, IT will replace the media or documentation at no charge. The purchaser must return the item to be replaced, with proof of purchase, to IT within 90 days after taking delivery of the software. IT warrants to the original purchaser that the hardware product is in good working condition for a period of 90 days from taking delivery of the product. Should this product, in IT's opinion, malfunction within the warranty period because of a defect in design, materials, or workmanship, IT will repair or replace this product without charge under the terms as follows. Replacement of either the hardware product or its component parts will be only on an exchange basis. Any replaced parts or components become the property of IT. This warranty does not apply to those products that have been damaged due to accident, abuse, improper installation, natural disaster, or unauthorized repairs or modifications. IT excludes any and all implied warranties, including warranties of merchantability and fitness for a particular purpose, and limits the purchaser's remedy to returning the software, hardware, or documentation to IT for replacement. IT makes no warranty or representation, either express or implied, with respect to this software, hardware, or documentation, their quality, performance, merchantability, or fitness for a particular purpose. This software, hardware, and documentation are licensed "as is," and the purchaser/licensee assumes the entire risk as to their quality and performance. In no event will IT be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the software, hardware, or documentation, even if advised of the possibility of such damages. The warranty and remedies set forth above are exclusive and in lieu of all others, oral or written, express or implied. No person, seller, dealer, agent, or employee is authorized to make any modification or addition to this limited warranty. Some states do not allow the exclusion of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
WORLD CLASS BOWLING - 27
INDUSTRY CANADA (IC) NOTICE
NOTICE: The industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local Telecommunications Company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions might not prevent degradation of service in some situations. A representative designated by the supplier should coordinate repairs to certified equipment. Any repairs or alterations made by a user to this equipment, or equipment malfunctions, may give the telephone communications company cause to request the user to disconnect the equipment. Users should ensure for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. NOTICE: The Ringer Equivalence Number (REN) assigned to teach terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices not exceed 5. REN: 1.0B WARRANTY AND REPAIR SERVICE: Incredible Technologies, Inc. 3333 N. Kennicott Ave. Arlington Heights, IL 60004 (847) 870-7027 + (847) 870-0120 Fax http://www. itsgames.com INCREDIBLE TECHNOLOGIES, INC 08/01
28 - WORLD CLASS BOWLING
a i __ A ee ll Incredible Technologies SALES AND SERVICE Contact the following for more information on ITNet and Golden Tee Fore! ITNet Sales Information: Check the IT web site at www.itsgames.com for an Authorized Distributor near you.
Sales Director Don Pesceone Incredible Technologies, Inc. (847) 870-7027 x189 (847) 870-0120 Fax dpesceone@itsgames.com Sales Coordinator Debi Bott Incredible Technologies, Inc. (847) 870-7027 x130 (847) 870-0120 Fax dbott@itsgames.com
_ITNet Service Information Technical Information: Incredible Technologies, Inc. 847-870-7027 x 121
Warranty and Repair: Incredible Technologies, Inc. 847-870-7027 x 177
Parts Orders: Incredible Technologies, Inc. 847-870-7027 x 190
VER. 08/01 Contents subject to change without notice. Mars Bill Acceptors: Mars Technical Service Phone: 800-345-8172
Wells-Gardner Monitors: Wells-Gardner Phone: 800-336-6630 Fax: 773-252-8299
Imperial Trackballs or Power Supplies Imperial Midwest: 800-386-7040 East Coast: 800-526-6261 West Coast: 800-423-2753
Happ Trackballs or Controls Happ Controls Phone: 800-BUY-HAPP
Hardware and Software ©Copyright 2001 Incredible Technologies, Inc. All rights reserved.
incredible
TECHNOLOGIES”
Incredible Technologies, Inc. 3333 N. Kennicott Ave.
Arlington Heights, IL 60004
(847) 870-7027 + (847) 870-0120 Fax http://www. itsgames.com
- ee
Ee ——