CATHODE RAY TOMES

Crystal Castles SP-241 1st Printing Troubleshooting Guide

Crystal Castles (version 4) (Atari, 1983) · Troubleshooting · 8 pages · 8 sections · original scan

Page 1

Crystal Castles" Troubleshooting Guide

‘A.Warner Communications Company

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Crystal Castles

A.

fy kw bw

il.

12. Troubleshooting Guide

Crystal Castles”

Troubleshooting with the CAT Box

Troubleshooting with the

Read/Write Controller

CAT Box Preliminary Set-Up Remove the electrical power from the game and the CAT Box.

Remove the wiring harness from the game PCB. Remove the game PCB from the game cabinet.

Remove Microprocessor 2C from the game PCB. Connect the harness from the game to the game PCB.

Connect together the 0 and ©2 test points on the game PCB with the shortest possible jumper. Connect the WDDIS test point to ground. Connect the CAT Box flex cable to the game PCB edge test connector. Apply power to the game and to the CAT Box. . Set CAT Box switches as indicated: a. TESTER SELF-TEST: OFF b. TESTER MODE: R/W

Press TESTER RESET.

Connect the DATA PROBE to the CAT Box. Connect the DATA PROBE ground clip toa game PCB ground test point.

Checking the Address Lines Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated:

a, BYTES: 1 b. PULSE MODE; UNLATCHED c. B/W MODE: (OFF) d. RAW: READ Key in the address pattern given in Table 1 (use AAAA to start) with the CAT Box keyboard. Set R/W MODE to STATIC.

Probe each IC-pin listed in Table 1 with the DATA PROBE and check that the CAT Box 1 or 0 LED for the corresponding address line lights up. Repeat parts 2-c through 5 using address 5555 in part 3. Table 1 Address Lines

Logic State for IC-Pin Logic State for Address AAAA Address 5555

BAIS11B30
BAl401B51
BAZ,11B70
BAI201B91
BAIL11B120
BAIO01B141
BAS11BI60
BAS01B181
BA711c90
BAG01C71
BAS11c50
BA40131
BAZ11C120
BA201C141
BAl11C160
BAO01C181

C. Checking the Data Lines

  • Perform the CAT Box preliminary set-up.
  • Set CAT Box switches as indicated:

a, BYTES:1 b. R/W MODE: (OFF) c. RAW: WRITE Key in address 0000 with the keyboard. Press DATA SET. Key in data AA with the keyboard. Set R/W MODE to STATIC. Probe each IC-pin listed in Table 2 with the DATA PROBE and check that the CAT Box 1 or 0 LED for the correspond: ing address line lights up. Set RAW MODE to (OFF). 8, Repeat parts 4 through 6 using data 55 in part 4. aad

~

Page 4

Troubleshooting Guide

Table 2 Data Lines

Logic State for IC-Pin Logic State for

Data AA Data 55

D712E-11oO
D6025-121
D512E-13,oO
D402E-141
D312E-15cv
D202E-161
DI12E-170
DO02E-181
BD712E-90
BD602E-81
BDS12E70
BD402E-61
BD312E-50
BD202E-41
BDI12E30
BDO02E-21

D. Checking the RAM Perform the CAT Box preliminary set-up.

  • Set CAT Box switches as indicated: a. DBUS SOURCE: ADDR b. BYTES:1024 c. RAW MODE: (OFF) d. R/W: WRITE
  • Enter address 0003 with the keyboard.
  • Set the CAT Box switches as indicated: a, _R/W MODE to PULSE and back to (OFF) b. RAW to READ ¢. RAW MODE to PULSE and back to (OFF)
  • Ifthe CAT Box reads an address that doesn’t compare with that written, the COMPARE ERROR LED will light up. The ADDRESS/SIGNATURE display of the CAT Box will show, the failing address location and the ERROR DATA DISPLAY switch is enabled. Using this switch, determine if the error is in the high-order or low-order RAM.
  • Repeat this test with DBUS SOURCE set to ADDR.
  • Set the CAT Box switches as indicated: a, BYTES: 256 b. DBUS SOURCE: ADDR c. B/W: (OFF) d. RAW: WRITE
  • Repeat parts 5 through 6 to check addresses from 1000 through 8FFF.
NOTE The two custom audio I/O chips must be tested separately by performing the self-test, substituting a known good part, or performing the following procedure. Crystal Castles

E. Checking the Custom Audio I/O Chips

1. Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated: a. BYTES: 1 b. RAW: WRITE c. R/W MODE: (OFF)

  • Enter the address from Table 3 with the keyboard.
  • Press DATA SET and enter the data from Table 3 with the keyboard.
  • Set R/W to PULSE and back to (OFF).
  • Repeat parts 3 through 5 for each address and data listedin Table 3, Check for the response indicated.

Table 3 Custom Audio i/O Chips

Address Data Test Results

9800Custom Audio I/O Chip 4D
9803channel 1 produces pure tone.

98 55 98 AF

9800Custom Audio I/O Chip 4D

channel | turns off.

9855Custom Audio I/O Chip 4D
98AFchannel 2 produces pure tone.
9800Custom Audio I/O Chip 4D

channel 2 turns off.

9A00Custom Audio I/O Chip 4B
OA03channel 1 produces pure tone.

9A 55 9A AF

9A00Custom Audio I/O Chip 4B

channel 1 turns off.

9A55Custom Audio I/O Chip 4B
9AAFchannel 2 produces pure tone.
9A00Custom Audio I/O Chip 4B

channel 2 turns off.

Page 5

Crystal Castles

EB

avaY Checking the Player Switch, Option Switch, and Trak-Ball™ Inputs Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated: a. BYTES: 1 b. RAW: WRITE c. RAV MODE: (OFF) Enter address 9600 with the keyboard. Press DATA SET and enter data FF with the keyboard. Set R/WE to PULSE and back to (OFF). For each entry listed in Table 4, do the following: Set R/W MODE to (OFF). Set R/WWRITE. Enter the first address with the keyboard. Press DATA SET and enter the data for that address with the keyboard, Set R/W MODE to PULSE and back to (OFF). Set R/W to READ. Enter the next address. Set RAW MODE to STATIC. Activate the input switch or signal indicated in Table 4and check the test result. Set RAW MODE to (OFF). Repeat parts g through j for each subsequent address given for the entry. aogPe

rire me

ae

Table 4 Player Switches, Option Switches, and Trak-Ball™ Inputs

Address Input

Test Results Switches/Signals Troubleshooting Guide

G. Checking the Coin Counter and Trak-Ball Light Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated:

a. DBUS SOURCE: DATA b. BYTES: 1 c. R/W: WRITE d. R/W MODE: (OFF) Enter the address in Table 5 with the keyboard.

CAUTION Ifyou write ON data to activate a solenoid, deactivate the solenoid immediately by writing the OFF data. If you leave a solenoid activated for more than 10 seconds, you may have to replace the solenoid and/or its driver, due to overheating.

For each address listed in Table 5, do the following: a. Toactivate the output: © Press DATA SET.

  • Enter the ON data with the keyboard.
  • Set R/W MODE to STATIC and back to (OFF). b. To deactivate the output: © Press DATA SET.
  • Enter the OFF data with the keyboard.
  • Set R/W MODE to STATIC and back to (OFF). Table 5 LED and Coin Counter Outputs

9400 Trak-Ball™ VERT 9401 ‘Trak-Ball™ HORIZ 9402 Trak-Ball™ VERT (Player 2) 9403 Trak-Ball™ HORIZ (Player 2) 9600 DO COINR DI COINL D2 COIN AUX D3 SLAM D4 SELF TEST DS SPARE D6 JMP1 D7 JMP2

Address On Off Output Device

Data Data

9E86FF00Left Coin Counter
SEBS.FF00Right Coin Counter
9E80FF00 = Trak-Ball™ Light

00-9A0B sw2 DO

sw3 Dt Sw4 D2 Read switches at address 9A08. DATA display changes when any of these switches or signals are activated.

Page 6

Troubleshooting Guide

Troubleshooting the Watchdog Circuit The Watchdog circuit will send continuous reset pulses to the microprocessor ifa problem exists within the microprocessor circuit. If the self-test fails to run, it is a good practice to check the RESET line. RESET is a microprocessor input (pin 40). In a properly operating game, reset should occur during power-upor when the RESET test pointis grounded, A pulsing RESET line indicates that something is causing the microprocessor to lose its place within the program. Typical causes are:

  • Open or shorted address or data bus lines. Crystal Castles
  • Bad microprocessor chip.
  • Bad bus buffers. 4, Bad ROM.
  • Bad RAM. 6. Any bad input or output that causes an address or data line to be held in a constant high or low state. A pulsing RESET signal indicates a problem exists somewhere within the microprocessor circuitry. To aid in troubleshooting, the WDDIS test point can be connected to a ground test point to prevent resets. This will sometimes allow the Self-Test to be used to diagnose the failure during a RESET condition.
Page 7

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.